BDP-150 BDP-150-K BDP-150-S

Add to my manuals
52 Pages

advertisement

BDP-150 BDP-150-K BDP-150-S | Manualzz

BDP-150_VXE8_IBD_EN.book 45 ページ 2012年3月12日 月曜日 午後4時10分

Troubleshooting

Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Inspect the other components and electrical appliances being used. If the trouble cannot be rectified even after checking the points below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.

Playback

Problem

• Disc does not play.

• Disc tray opens automatically.

Check

Is the disc one that is playable on this player?

Remedy

Check whether the disc is one that can be played on this player

(page 6).

Is the file one that is playable on this player?

• Check whether the file is one that can be played on this player

(page 9).

• Check whether or not the file is damaged.

Is the disc scratched?

Is the disc dirty?

It may not be possible to play scratched discs.

Clean the disc (page 44).

Is there a piece of paper or sticker attached to the disc?

The disc may be warped and unplayable.

Is the disc properly set in the disc tray?

• Set the disc with the printed side facing up.

• Set the disc properly in the depression in the disc tray.

Is the region number correct? See page 8 for the region numbers of discs that can be played on this player.

No picture is displayed or the picture is not displayed properly.

Is the video cable properly connected?

• Connect the cable properly according to the connected devices

(page 13).

• Disconnect the cable (video/audio cable or HDMI cable), then reinsert it firmly and all the way in.

Is the video cable damaged?

If the cable is damaged, replace it with a new one.

Is the input setting on the connected TV or AV receiver or amplifier right?

Read the operating instructions for the connected components and switch to the proper input.

Is the output video resolution properly set?

• Press HDMI to switch the video resolution output from the HDMI

OUT terminal (page 11).

• Is the player connected with an HDMI cable other than a High Speed HDMI

®

/

TM

cable (with a Standard

HDMI

®

/

TM

cable)?

• Are you using an HDMI cable with a built-in equalizer?

1080p or Deep Color video signals may not be output properly, depending on the HDMI cable being used or the player’s settings. If you wish to output the video signals with 1080p or Deep Color, connect the

TV using a High Speed HDMI

®

/

TM

cable without a built-in equalizer, then reset the player using the Setup Navigator (page 19).

Is a DVI device connected?

The picture may not be displayed properly if a DVI device is connected.

Playback stops.

Picture freezes and the front panel and remote control buttons stop working.

Is Color Space properly set?

Change the Color Space setting (page 35).

• Playback may stop if the unit is subject to shocks or set in an unstable place.

• Playback may stop when a USB device is connected or disconnected during playback. Do not connect or disconnect USB devices during playback.

• Press

 to stop playback, then restart playback.

• If the playback cannot be stopped, press

STANDBY/ON on the player’s front panel to turn off the power, then turn the power back on.

• If the power cannot be turned off (set to standby), use a thin rod to press the reset button on the main unit’s front panel. The unit restarts, at which point it is again operable.

No picture is displayed or picture is not output in high definition when playing BDs.

With some discs, it may not be possible to output the video signals from the VIDEO output terminal. In this case, connect using an HDMI cable

(page 13).

08

45

En

BDP-150_VXE8_IBD_EN.book 46 ページ 2012年3月12日 月曜日 午後4時10分

08

46

En

Problem

• Picture is disturbed during playback.

• Picture is dark.

• Picture is stretched.

• Picture is cropped.

• Aspect ratio cannot be switched.

Picture is interrupted.

The subtitles cannot be switched.

• No sound is output.

• Sound is not output properly.

Check

Is the TV’s aspect ratio properly set?

Is TV Screen properly set?

Remedy

• This player supports Rovi analog copy protection technology. With some TVs (such as with built-in video deck), the picture will not be displayed properly when the copy protected DVD title is played. This is not a malfunction.

• If the player and TV are connected via a DVD recorder/video deck, etc., the picture will not be displayed properly due to analog copy protection. Connect the player and TV directly.

Read the operating instructions for the TV and set the TV’s aspect ratio properly.

Set TV Screen properly (page 33).

When video signals with a resolution of 1080/50i, 1080/50p, 720/50p,

1080/24p, 1080/60i, 1080/60p or 720/60p are being output from the

HDMI OUT terminal, they may be output with an aspect ratio of 16:9 even if TV Screen is set to 4:3 Pan&Scan (page 33).

The picture may be interrupted when the resolution of the recorded video signal switches. Press HDMI to select a setting other than Auto

(page 35).

The subtitles cannot be switched for discs recorded on a DVD or BD recorder.

Is the disc played back in slow motion?

Is the disc played back in fast forward or fast reverse?

No sound is output during slow motion play and forward and reverse scanning.

Are the audio cables properly connected?

• Connect the cable properly according to the connected devices

(page 13).

• Insert the cable firmly and all the way in.

Is the audio cable damaged? If the cable is damaged, replace it with a new one.

Is Audio Output properly set?

Set Audio Output properly, according to the connected device

(page 34).

Are the connected components (AV receiver or amplifier, etc.) properly set?

Read the operating instructions for the connected components and check the volume, input, speaker settings, etc.

Are you trying to listen to the sound of the HDMI OUT terminal while watching the picture from the VIDEO output terminals?

Audio signals are not output from the HDMI OUT terminal when video signals are being output from the VIDEO output terminals. When watching the picture of the VIDEO output terminals, connect an coaxial digital audio cable or regular audio cables to listen to the sound

(page 16). Once connections are completed, use Setup Navigator to make the player’s settings (page 19).

Is HDMI Audio Out properly set?

Set HDMI Audio Out to Re-encode or PCM. (page 35).

Multi-channel sound is not output.

Is a DVI device connected?

The sound will not be output from the HDMI OUT terminal if a DVI device is connected. Connect the device to a DIGITAL OUT terminal or the AUDIO OUT terminals (page 16).

Is the audio output of the connected AV receiver or amplifier, etc., properly set?

Is multi-channel sound selected?

For some BDs, audio signals are only output from DIGITAL OUT terminal or the HDMI OUT terminal.

Read the operating instructions for the connected AV receiver or amplifier and check the audio output settings of the AV receiver or amplifier.

Use the menu screen or AUDIO to switch the disc’s sound to multichannel.

Noise can be heard when outputting DTS Digital Audio signals from the

DIGITAL

OUT terminal.

Is the connected AV receiver or amplifier compatible with

DTS Digital Surround?

If an AV receiver or amplifier that is not compatible with DTS Digital

Surround is connected to the DIGITAL OUT terminal, set Digital

Output to PCM (page 34).

192 kHz or 96 kHz digital audio signals cannot be output from the

DIGITAL

OUT terminal.

It is not possible to output 192 kHz or 96 kHz digital audio signals from this player’s DIGITAL OUT terminal. The signals are automatically converted to 48 kHz or less for output.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents