Operator`s Manual for Basic Functions CX1145 MFP

Add to my manuals
341 Pages

advertisement

Operator`s Manual for Basic Functions CX1145 MFP | Manualzz

Configuration of options

10 11

1 2

7 8

3

9

4 5 6

1. Original Cover (KA-3511PC)

Holds an original.

2. Reversing Automatic Document Feeder (MR-3018)

Automatically feeds a placed stack of originals one by one to have them copied.

3. Bridge Unit (KN-3511A)

Acts as a relay for the finisher and this equipment.

4. Large Capacity Feeder (KD-1012)

This feeder enables you to feed up to 2500 sheets (20 lb. Bond) of LT paper.

5. Paper Feed Pedestal (KD-1011)

Adds one drawer to the equipment. This also enables you to install the Additional Drawer Module (MY-

1021) (optional).

6. Additional Drawer Module (MY-1021)

This drawer is for adding to the Paper Feed Pedestal (KD-1011). Combined with the 2 drawers in the equipment, paper can be fed from 4 drawers in total.

7. Finisher (MJ-1101)

This finisher enables sort/group finishing and stapling. The Hole Punch Unit (optional, MJ-6101) can be installed to this finisher. The Bridge Unit (optional, KN-3511A) is required for the installation of this finisher.

1

8

1.Description of Each Component (Cont.)

1

8. Saddle Stitch Finisher (MJ-1024)

This finisher enables saddle stitching, in addition to sort/group finishing and stapling. The Hole Punch

Unit (optional, MJ-6004) can be installed to this finisher. The Bridge Unit (optional, KN-3511A) is required for the installation of this finisher.

9. Multi Position Staple Finisher (MJ-1023)

This finisher enables sort/group finishing and stapling. The Hole Punch Unit (optional, MJ-6004) can be installed to this finisher. The Bridge Unit (optional, KN-3511A) is required for the installation of this finisher.

10. Hole Punch Unit (MJ-6101)

This unit enables you to punch holes on printouts. It can be used by installing it on the Finisher

(MJ-1101).

11. Hole Punch Unit (MJ-6004)

This unit enables you to punch holes on printouts. It can be used by installing it to the Saddle Stitch

Finisher (MJ-1024) and Multi Position Staple Finisher (MJ-1023).

Other options available are as follows. Contact your service technician or OKI product distributors for details.

Work Table (KK-3511)

This is a small table for placing originals while the equipment is operated.

• Cannot be installed with e-BRIDGE ID Gate at the same time.

FAX Unit (GD-1201)

This is a unit for using the equipment as a Fax.

2nd Line for Fax Unit (GD-1260)

This unit enables to add a line to the Fax to make it 2nd line.

• The Fax Unit (GD-1201) is necessary.

Desk (MH-1700)

This is a desk for the equipment.

Data Overwrite Kit (GP-1060)

This is a kit to erase the data stored temporarily when copying, printing, scanning, Fax, internet Fax or network Fax is performed. It overwrites temporarily stored data with random data.

Scrambler Board (GP-1040)

This board enhances the security of the equipment. Data are encrypted when they are written into the hard disk of the equipment and decrypted when they are read.

Parallel Board (GF-1140)

This kit is used when the equipment is connected in parallel with a computer.

• The PCI slot (GO-1060) is necessary.

Expansion Memory (GC-1181, GC-1230)

GC-1181 is a page memory for storing data temporarily when scanning or printing.

9

1.BEFORE USING EQUIPMENT

GC-1230 is a main memory used for the equipment programs or operations. Both of them are necessary for the memory expansion. High resolution scanning (Color/Auto color: 600/400 dpi, Image Smoothing:

600 dpi) and high resolution color printing (1201 dpi equiv. x 600 dpi) functions are enhanced.

Wireless LAN Module (GN-1041)

This module enables the equipment to be used in a wireless LAN environment.

• The Antenna (GN-3010) is necessary.

• The equipment cannot be connected to the wireless and wired LAN at the same time.

Bluetooth Module (GN-2010)

This module enables the Bluetooth printing.

• The Antenna (GN-3010) is necessary.

Antenna (GN-3010)

This is used when the Wireless LAN Module and Bluetooth Module are installed.

e-BRIDGE ID Gate (KP-2004, KP-2005)

Users can login and use the equipment simply by holding their IC card over the e-BRIDGE ID Gate.

• This cannot be installed with the Work Table at the same time.

1

10

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents