Operator`s Manual for Basic Functions CX1145 MFP

Add to my manuals
341 Pages

advertisement

Operator`s Manual for Basic Functions CX1145 MFP | Manualzz

2.Making Copies (Cont.)

2

Copying procedure

Placing originals on the Reversing Automatic Document Feeder (optional)

1 Place paper in the drawer(s).

• For the types and sizes of paper selectable, see

! P.30 “Acceptable copy paper”.

When the desired size or type of paper is not in any of the drawers or the Large Capacity Feeder, see the following pages.

-

! P.32 “Setting copy paper (size change)”

-

! P.37 “Placing paper in the Large Capacity Feeder (optional)”

-

! P.58 “3.Bypass Copying”

2 Place the original(s).

• See the following pages to set the originals.

-

! P.43 “Acceptable originals”

-

! P.47 “Using the Reversing Automatic Document Feeder

(optional)”

The originals are copied in the order of being scanned.

3 Select the copy modes as required. When you want to copy more than one set, key in the desired number of copies.

• Press the [CLEAR] button on the control panel to correct the number keyed in.

• Note that some combinations of copy modes are restricted. (

! P.338 “4.Copying Function Combination

Matrix”,

! P.340 “5.Image Quality Adjustment Combination Matrix” )

• Once the [START] button on the control panel has pressed, any change in copy modes (including setting of the previously divided sets of originals) cannot be applied afterward.

51

2.HOW TO MAKE COPIES

4 Press the [START] button.

• Copying starts. The paper exits with its copied side down.

• When the drawer runs out of paper during copying, a paper source of the same size and direction is automatically selected and copying continues.

• When the drawer runs out of paper during copying, the corresponding drawer on the touch panel and the [JOB STATUS] button on the control panel blink. Add paper to this drawer or select another one with the same paper size.

• Be careful because the paper exit area and paper just after exiting are hot.

Placing an original on the original glass

1 Place paper in the drawer(s).

• For the types and sizes of paper selectable, see

! P.30 “Acceptable copy paper”.

When the desired size or type of paper is not in any of the drawers or the Large Capacity Feeder, see the following pages.

-

! P.32 “Setting copy paper (size change)”

-

! P.37 “Placing paper in the Large Capacity Feeder (optional)”

-

! P.58 “3.Bypass Copying”

2 Place the original(s).

• See the following pages to set the originals.

-

! P.43 “Acceptable originals”

-

! P.45 “Placing originals on the glass”

The originals are copied in the order of being scanned.

3 Select the copy modes as required. When you want to copy more than one set, key in the desired number of copies.

2

• Press the [CLEAR] button on the control panel to correct the number keyed in.

• Note that some combinations of copy modes are restricted. (

! P.338 “4.Copying Function Combination

Matrix”,

! P.340 “5.Image Quality Adjustment Combination Matrix”)

• Once the [START] button on the control panel has pressed, any change in copy modes (including setting of the previously divided sets of originals) cannot be applied afterward.

52

2.Making Copies (Cont.)

2

4 Press the [START] button.

• Copying starts.

When you copy by placing originals on the original glass (e.g. using the sort mode, or making 1-sided original 2-sided copies), the data of these originals are scanned into the memory. In this case, proceed to steps 5 and 6.

5 Place the next original, and press the [START] button.

• Data scanning of this original starts.

• The next original will also be scanned in the same manner when you press the [YES] button on the touch panel and then press the [START] button on the control panel.

• Repeat the above procedure until the scanning of the last page of the original finishes.

6 When scanning of all pages has finished, press the [FINISHED] button on the touch panel.

• Copying starts. The paper exits with its copied side down.

• When the drawer runs out of paper during copying, the corresponding drawer on the touch panel and the [JOB

STATUS] button on the control panel blink. Add paper to this drawer or select another one with the same paper size.

• Be careful because the paper exit area and paper just after exiting are hot.

53

2.HOW TO MAKE COPIES

Stopping the copying operation

Press the [STOP] button on the control panel to stop scanning or continuous copying.

1 Press the [STOP] button on the control panel during scanning (or continuous copying).

2 When the following menu is displayed, press the [MEMORY CLEAR] button on the touch panel.

2

• During scanning: The data scanned up to then are deleted.

• During continuous copying: Copying stops and the data scanned up to then are deleted.

If there is any copy job waiting, this job will start.

54

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents