Operator`s Manual for Basic Functions CX1145 MFP

Add to my manuals
341 Pages

advertisement

Operator`s Manual for Basic Functions CX1145 MFP | Manualzz

2

3.Bypass Copying (Cont.)

Bypass copying on non-standard size paper

Non-standard size paper should be within the following ranges:

A (Length): 3.9" to 11.7", B (Width): 5.8" to 17"

B

A

1 Place some sheets of paper with their copy side down on the bypass tray. Align the side guides to the paper length while holding A.

• The message “Ready for bypass feeding” appears.

• Rear side of the side guides of the bypass tray has an indicator for paper height. The height of the sheets must not exceed this indicator.

• When you use more than one sheet, fan the sheets well before setting them on the tray.

• Do not push the sheets into the entrance of the bypass feeder; it may cause a paper jam.

A

When the paper size is larger, draw out the three-stage paper holder. Raise B when you use LD or a larger size of paper.

2 Place the original on the original glass.

B

63

2.HOW TO MAKE COPIES

3 Press the [NON STANDARD] button on the touch panel.

4 Set each dimension following the procedure below.

The [Length] and [Width] are indicated as follows:

A: [Length]

B: [Width]

A

B

Using the digital keys

Key in the value in [Length] and press the [SET] button on the touch panel. Set the width in the same way and press the [ENTER] button.

2

64

2

3.Bypass Copying (Cont.)

Recalling dimensions registered in the memory

Press the desired memory number button from [MEMORY 1] to [MEMORY 4] to recall the dimension data registered previously, and then press the [ENTER] button.

• Paper size that can be set is as follows:

Length: 100 mm (3.94") to 297 mm (11.69")

Width: 148 mm (5.83") to 432 mm (17.01")

• To register the dimension data in the memory, see

! P.65 “Registering non-standard size in the memory”.

• Set other copy modes as required.

5 Press the [START] button on the control panel.

Registering non-standard size in the memory

1 Follow steps 1 to 3 on “Bypass copying on non-standard size paper”

(

! P.63).

2 Press the memory number button (from [MEMORY 1] to [MEMORY 4]) you want to register the dimension.

65

2.HOW TO MAKE COPIES

3 Key in each dimension, and press the [MEMORY] button on the touch panel.

2

• Key in its length in [Length] and press the [SET] button on the touch panel. Set its width in the same manner.

• Paper size that can be set is as follows:

Length: 100 mm (3.94") to 297 mm (11.69")

Width: 148 mm (5.83") to 432 mm (17.01")

66

4. Proof Copy

This function allows you to check that the copy density, zoom and margin width, etc. are properly set by making only one set of copies.

You can prevent miscopying by using this function before committing yourself to mass-copying.

2

• The setting of the number of copy sets, page number, time stamp, sort/stapling (when the optional Finisher has been installed) and hole punch (when the optional Hole Punch Unit has been installed) can be changed after having made the proof copy.

• Press the [MEMORY CLEAR] button to clear the proof copy before changing the setting of the zoom or copy density, etc. When you make copies again after changing the settings, the data of the originals need to be scanned.

1

Place paper in the drawer(s).

2 Place the original(s).

3

Select the copy modes as required.

4 Press the [PROOF COPY] button.

• “PROOF COPY is set Press START button to copy” appears. (for approx. 2 sec.)

• If “NON-SORT/NON-STAPLE” or “GROUP” is set as the finishing mode, the setting will be changed to “SORT” automatically.

5 Press the [START] button.

• The data scanning of the originals is started and one set of copies is made.

67

2.HOW TO MAKE COPIES

6 Change the settings as required.

• The setting of the number of copy sets, page number, time stamp, sort/stapling (when the optional Finisher has been installed) and hole punch (when the optional Hole Punch Unit has been installed) can be changed.

• If you want to change the setting of the copy density, original mode, zoom or simplex/duplex, press the

[MEMORY CLEAR] button to clear the proof copy. After the change, perform the instructions from step 1 again.

7

Press the [START] button.

• If the number of copy sets is not changed in step 6, one less than the previously specified number is copied.

However, if “1” is specified for the number of copy sets, one set of copies is made.

2

68

2

4.Proof Copy (Cont.)

69

2.HOW TO MAKE COPIES

3. SETTING BASIC COPY MODES

1. Paper Selection.................................................................................................................... 71

• Automatic Paper Selection (APS) .....................................................................................................71

• Manual paper selection .....................................................................................................................73

• Copying mixed-size originals in one go (mixed original size)............................................................74

2. Switching Color Mode .......................................................................................................... 76

3. Enlargement and Reduction Copying ..................................................................................77

4. Selecting Finishing Modes ................................................................................................... 83

• Type of finishing mode ......................................................................................................................83

• Name of each part in the Finisher (optional) .....................................................................................84

• Sort/Group copying ...........................................................................................................................85

• Rotate sort mode...............................................................................................................................87

• Staple sort mode ...............................................................................................................................88

• Magazine sort & saddle stitch mode (booklet mode) ........................................................................90

• Hole punch mode (optional) ..............................................................................................................93

• Manual stapling (MJ-1101 only) ........................................................................................................95

5. Duplex Copying.................................................................................................................... 97

6. Original Mode..................................................................................................................... 106

7. Copy Density Adjustment...................................................................................................108

3

70

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents