Operator`s Manual for Basic Functions CX1145 MFP

Add to my manuals
341 Pages

advertisement

Operator`s Manual for Basic Functions CX1145 MFP | Manualzz

Copying mixed-size originals in one go (mixed original size)

You can copy a set of originals whose sizes are individually different, using the Reversing Automatic Document Feeder (optional), by pressing the [MIXED ORIGINAL SIZE] button.

• This mixed original size setting is available only in the following combinations.

LD, LG, LT, LT-R, 8.5", SQ, COMP

• Note that the copied image may be dislocated depending on the combination.

1 Place paper in the drawer(s).

• Bypass copying is not available.

2 Adjust the side guides to the widest original, and then align the original against the guide at the front side.

• Place the originals face up.

3

3

Press the Enlargement/Reduction ([ZOOM...]) button to enter the setting menu of the original or paper size.

4

Press the [MIXED ORIGINAL SIZES] button.

74

3

1.Paper Selection (Cont.)

5 Select either automatic paper selection (APS) or automatic magnification selection (AMS).

Automatic paper selection: Copies on the same size of paper as that of originals (

! P.71).

Automatic magnification selection: Copies all in one size (

! P.77).

• Before you use automatic paper selection, be sure that all paper sizes corresponding to the original sizes have been set in the drawers.

• In automatic magnification selection, the copies cannot be enlarged from LT (portrait) to LD (landscape)/LG

(landscape).

• If “Change direction of original” appears when [AMS] is used with [MIXED ORIGINAL SIZES], change the direction according to the message.

• Set other copy modes as required.

6 Press the [START] button.

75

3.SETTING BASIC COPY MODES

2. Switching Color Mode

This function allows you to switch color modes. There are three types of color modes as follows:

FULL COLOR: All originals are copied in full color regardless of the type of each original.

BLACK: All originals are copied in black regardless of the type of each original. (Default setting)

AUTO COLOR: The equipment automatically judges the type of each original. Colored originals are copied in full color and black-and-white originals are copied in black.

1 Press the [FULL COLOR], [BLACK] or [AUTO COLOR] button.

3

When you use “AUTO COLOR”, note the following points:

When the colored area in an original is extremely small, when the colors of the original are close to black, or when the colors of an original are too light, these originals may be automatically copied in black even though they are colored. Also yellowed originals or originals with a colored background may be automatically copied in full color even though they are black-and-white. Select the full color mode or the black mode depending on the state of the original to reproduce exact colors.

76

3. Enlargement and Reduction Copying

You can enlarge or reduce the size of copies by means of the following procedures.

• Specifying the copy paper size in advance so that the equipment will detect the original size and automatically select the most appropriate reproduction ratio for the copy paper size (= automatic magnification selection)

• Specifying both original size and copy paper size separately

• Using the zoom buttons or the one-touch zoom buttons

3

The enlargement/reduction ratio available differs depending on whether the originals have been set on the original glass or on the Reversing Automatic Document Feeder (optional).

On the original glass: 25 to 400%

On the Reversing Automatic Document Feeder: 25 to 200%

Automatic Magnification Selection (AMS)

• The automatic magnification selection cannot be selected for the following originals. Set their reproduction ratios in other ways.

Highly transparent originals (e.g. OHP film, tracing paper)

Wholly dark originals or originals with dark borders

Non-standard size originals (e.g. newspapers, magazines)

• For the original sizes available for this automatic magnification selection, see

! P.43 “Acceptable originals”.

1 Place paper in the drawer(s).

2 Press the Enlargement/Reduction ([ZOOM...]) button.

77

3.SETTING BASIC COPY MODES

3 Press the button representing the desired copy paper size.

E.g.: When LT-size paper is selected

• The copy paper size can also be set by pressing the drawer button on the touch panel.

4 Press the [AMS] button.

5 Place the original(s).

• If “Change direction of original” appears, make the change accordingly.

• Set other copy modes as required.

6 Press the [START] button.

3

78

3.Enlargement and Reduction Copying (Cont.)

3

Specifying both original size and copy size separately

1 Place paper in the drawer(s).

2 Place the original(s).

3 Press the Enlargement/Reduction ([ZOOM...]) button.

4 Specify the original size and copy paper size.

Original size: Press the size button representing the same size as that of the set original.

Copy paper size: Press the size button representing the desired copy paper size.

E.g.: When LD for the original size and LT for the copy paper size are selected

• The copy paper size can also be set by pressing the drawer button on the touch panel.

• When the original size and copy paper size have been specified, the enlargement/reduction ratio is computed and displayed on the touch panel.

• Set other copy modes as required.

When the original or copy paper is a standard size other than LD, LG, LT or ST, you need to register this paper size in the selections of the [OTHER] button in advance. See “When a standard size paper other than LD, LG, LT and ST-R is set” below for the registration.

5 Press the [START] button.

79

3.SETTING BASIC COPY MODES

When a standard size paper other than LD, LG, LT and ST-R is set

Register the size of the placed paper to the [OTHER] button with the following procedure. The registered paper size is automatically selected when the [OTHER] button is pressed.

1 Press the [OTHER SIZE] button.

3

2 Press the paper size button corresponding to the paper that has been set.

E.g.: When COMP-size paper is set

3 Press the [OTHER] button.

80

3.Enlargement and Reduction Copying (Cont.)

3

Using the zoom buttons or the one-touch zoom buttons

1 Place paper in the drawer(s).

2 Place the original(s).

3 Press the Enlargement/Reduction ([ZOOM...]) button.

4 Press the following buttons to set the desired reproduction ratio.

A: Zoom ([

Up] and [ Down]) buttons

The reproduction ratio changes by 1% every time it is pressed. When you hold down either of them, the ratio goes up or down automatically.

B: One-touch zoom buttons

You can select the ratio from [400%], [200%], [100%], [50%] and [25%].

• The maximum ratio when the Reversing Automatic Document Feeder (optional) is used is 200%.

A

B

81

3.SETTING BASIC COPY MODES

5 Press the button representing the desired copy paper size.

E.g.: When LD-size paper is selected

• The copy paper size can also be set by pressing the drawer button on the touch panel.

• Set other copy modes as required.

6 Press the [START] button.

3

82

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents