Operator`s Manual for Basic Functions CX1145 MFP

Add to my manuals
341 Pages

advertisement

Operator`s Manual for Basic Functions CX1145 MFP | Manualzz

4.Selecting Finishing Modes (Cont.)

3

Manual stapling (MJ-1101 only)

The manual stapling function which enables you to use the staple function without making copies is available in the Finisher (MJ-1101, optional). This function is useful when copies are made without stapling being set or when you want to staple originals.

A: Stapling position lamps

B: [Stapling position] button

C: Manual-stapling lamp

D: [Manual-stapling] button

A B C D

1 Press the [Manual-stapling] button.

The shutter in the paper exit area is opened.

2

Press the [Stapling position] button to switch the stapling position.

Stapling positions are the front and the other end.

The stapling position lamp corresponding to the selected stapling position lights in green.

3

Place paper in the lower tray of the finisher.

Jog the paper well and place it with its face down.

Place the paper in front to have it stapled in the front, and in the other end to have it stapled in the other end.

Check that the manual-stapling lamp lights in green. If not, place the paper again.

4

Release the paper and press the [Manual-stapling] button.

The stapling position lamp blinks when the stapling is completed. Remove the paper.

Be sure to release the paper before the manual stapling.

95

3.SETTING BASIC COPY MODES

• Operation can be continued while the manual-stapling lamp lights. If no operation is performed for approx. 15 min., the manual stapling operation is stopped.

• If you want to stop the manual stapling operation during setting, remove paper and press the [Manual-stapling] button. The shutter in the paper exit area is closed and the operation of the manual stapling is finished.

Specification

Acceptable paper size

Maximum number of sheets for stapling

Stapling position

LD, LG, LT, LT-R, COMP, 13” LG, 8.5” SQ, 8K, 16K, A3, A4, A4-R, B4

50 sheets (LT, 8.5” SQ, 16K, A4: 17 - 20 lb. Bond)

30 sheets (LD, LG, LT-R, COMP, 13” LG, 8K, A3, A4-R, B4, FOLIO:

17 - 20 lb. Bond)

30 sheets (LT, 8.5” SQ, 16K, A4: 21 - 28 lb. Bond)

15 sheets (LD, LG, LT-R, COMP, 13” LG, 8K, A3, A4-R, B4, FOLIO:

21 - 28 lb. Bond)

Front, Rear

3

96

5. Duplex Copying

3

The following 5 combinations are available for duplex copying.

1. 1-sided original -> 1-sided copy (default setting at installation)

2. 1-sided original -> 2-sided copy

3. 2-sided original -> 2-sided copy

4. 2-sided original -> 1-sided copy

5. Book-type original -> 2-sided copy

• Duplex copying is available for plain paper (17 to 20 lb. Bond) and thick 1 paper (- 28 lb. Bond).

1

2

3

4

5

-12-15-12-15-

97

3.SETTING BASIC COPY MODES

1-sided original -> 1-sided copy (default setting at installation)

1 Place paper in the drawer(s).

2 Place the original(s).

3 Confirm that the simplex/duplex button on the basic menu is [1 -> 1

SIMPLEX].

3

• If [1 -> 1 SIMPLEX] is not shown, press the simplex/duplex button to display the next menu, and then press the

[1 -> 1 SIMPLEX] button on that menu.

• Set other copy modes as required.

4 Press the [START] button.

98

5.Duplex Copying (Cont.)

1-sided original -> 2-sided copy

3

When you copy 1-sided portrait originals to 2-sided copies placing them in a landscape direction, you can make a booklet-type copy in the direction of “open toward the left” opening, using the image direction

mode in the edit menu. (

! P.158 “14.IMAGE DIRECTION”)

1 Place paper in the drawer(s).

• When using this mode in bypass copying, specify the paper size in advance. (

! P.58 “3.Bypass Copying”)

2

Place the original(s).

3 Press the simplex/duplex button on the basic menu.

4 Press the [1 -> 2 DUPLEX] button.

• Set other copy modes as required.

5 Press the [START] button.

• When placing an original on the original glass, follow steps 5 to 6 of

! P.52 “Placing an original on the original glass” continuously.

99

3.SETTING BASIC COPY MODES

2-sided original -> 2-sided copy

1 Place paper in the drawer(s).

• When using this mode in bypass copying, specify the paper size in advance. (

! P.58 “3.Bypass Copying”)

2 Place the original(s).

3 Press the simplex/duplex button on the basic menu.

3

4 Press the [2 -> 2 DUPLEX] button.

• Set other copy modes as required.

5 Press the [START] button.

• When placing an original on the original glass, follow steps 5 to 6 of

! P.52 “Placing an original on the original glass” continuously.

100

5.Duplex Copying (Cont.)

2-sided original -> 1-sided copy

3

When a 2-sided ‘open to left’ (Book) portrait original is copied using the image direction mode in the edit menu with [2-Sided Originals to 1-Sided Copies], copies can be adjusted to the same direction. (

! P.158

“14.IMAGE DIRECTION”)

1 Place paper in the drawer(s).

2

Place the original(s).

3 Press the simplex/duplex button on the basic menu.

4 Press the [2 -> 1 SPLIT] button.

• Set other copy modes as required.

5 Press the [START] button.

101

3.SETTING BASIC COPY MODES

Book-type original -> 2-sided copy

You can make a booklet-type copy in the same page configuration in which the original is.

• The acceptable paper size for this function is LT only.

1 Place paper in the drawer(s).

• When using this mode in bypass copying, specify the paper size in advance. (

! P.58 “3.Bypass Copying”)

2 Press the simplex/duplex button on the basic menu.

3

3 Press the [BOOK -> 2] button.

102

5.Duplex Copying (Cont.)

4 Select the book copying type.

3

• Press the [RIGHT -> RIGHT] button (= default setting at the installation) if copying should start at a right-hand page and end at a right-hand page. Other copying types are selectable by pressing any of the [RIGHT ->

LEFT], [LEFT -> LEFT] and [LEFT -> RIGHT] buttons.

e.g.: If pages 2 to 6 of a book which opens to the left are to be copied, select [LEFT -> RIGHT].

A B E F

2 3 6 7

• The yellow indicator line for booklet copying moves to the center of the original glass.

103

3.SETTING BASIC COPY MODES

5 Select LT copy size.

• Only LT size is available. Press the drawer button on the touch panel, or use the paper source selection ( / ) buttons to select LT size.

3

• If you need a binding space, select the book margin mode. (

! P.121 “1.IMAGE SHIFT”)

• Set other copy modes as required.

6 Open and place the first page(s) on the original glass.

• Center the booklet on the yellow indicator line with its bottom toward you.

Do not place heavy objects (9 lb. or more) on the original glass and do not press on it with force. Breaking the glass could injure you.

7 Press the [START] button. When the data of the opened pages have been scanned, open the next page and set the booklet on the original glass again.

• Repeat the procedures above until all the desired pages have been scanned. If the last copy is only a single page, press the [COPY FINAL PAGE] button on the touch panel before the scanning of this page is started.

The scanned pages will be copied.

104

3

5.Duplex Copying (Cont.)

8 When all the pages have been scanned, press the [FINISHED] button on the touch panel.

• The scanned pages will be copied.

• For setting image shift, see

! P.125 “Creating a bookbinding margin”.

105

3.SETTING BASIC COPY MODES

6. Original Mode

You can make copies with optimal image quality by selecting the following modes for your original.

The selectable original mode differs depending on the color mode (

! P.76). Switch the color mode first,

and then select the original mode.

Full color

TEXT/PHOTO:

TEXT:

PHOTO:

PRINTED IMAGE:

MAP:

Originals with text and photographs mixed (Default setting)

Originals with text (or text and line art) only

Originals with general photographs on photographic printing paper

Originals with photogravure (e.g. Magazine, brochure)

Originals with fine illustrations or text

Black

TEXT/PHOTO:

TEXT:

PHOTO:

Originals with text and photographs mixed (Default setting)

Originals with text (or text and line art) only

Originals with photographs

IMAGE SMOOTHING: Originals with text and photographs mixed, especially originals requiring higher reproducibility on photos

Auto color

TEXT/PHOTO: Originals with text and photographs mixed

1

Place paper in the drawer(s).

2 Place the original(s).

3

Press the original mode button on the basic menu.

3

106

3

6.Original Mode (Cont.)

4 Select and press the button for the most appropriate original mode for your original.

The selectable original mode differs depending on the color mode as follows.

Full color

Black

Auto color

• Set other copy modes as required.

5 Press the [START] button.

107

3.SETTING BASIC COPY MODES

7. Copy Density Adjustment

There are 2 types of copy density adjustment: the automatic copy density mode and the manual copy density mode. In the automatic copy density mode, the equipment automatically selects the most appropriate copy density by detecting the density of the original. In the manual copy density mode, you can adjust the copy density manually according to the conditions of the original.

• Default setting: Manual density mode for “FULL COLOR” / “AUTO COLOR”, Automatic density mode for “BLACK”

Automatic copy density mode

1 Place paper in the drawer(s).

2

Place the original(s).

3 Confirm that the [AUTO] button on the basic menu is selected. If it is not, press the button.

3

• Set other copy modes as required.

4 Press the [START] button.

108

7.Copy Density Adjustment (Cont.)

3

Manual copy density mode

1 Place paper in the drawer(s).

2 Place the original(s).

3 Press either the or button to adjust the copy density to the desired level.

• The copied image becomes lighter as you press the button and darker as you press the button.

• Set other copy modes as required.

4

Press the [START] button.

109

3.SETTING BASIC COPY MODES

4. IMAGE ADJUSTMENT

1. Color Balance (YMCK Adjustment).................................................................................... 111

2. RGB Adjustment ................................................................................................................ 112

3. One-Touch Adjustment ...................................................................................................... 113

4. Background Adjustment ..................................................................................................... 114

5. Sharpness .......................................................................................................................... 115

6. Twin Color (2-Color) Copy ................................................................................................. 116

4

110

1. Color Balance (YMCK Adjustment)

4

This function allows you to adjust an overall color balance of the copied image by changing each toner amount of yellow (Y), magenta (M), cyan (C) and black (K).

• This function is available only in the full color mode.

1 Place paper in the drawer(s).

2

Place the original(s).

3 Press the [IMAGE] button to enter the image menu, and then press the

[COLOR BALANCE] button.

4 Press the or button of the color to obtain the desired color balance. Then press the [ENTER] button.

• “0” is the standard setting.

• Pressing the button strengthens the adjusted color, and pressing the button weakens it.

• Select other copy modes as required.

5 Press the [START] button.

Canceling the color balance adjustment

Move the indicator of the color whose adjustment you want to cancel its adjustment to 0 by your pressing the or button, and then press the [ENTER] button.

If you want to cancel the adjustment of all colors, press the [DEFAULT] button, and then press the

[ENTER] button.

111

4.IMAGE ADJUSTMENT

2. RGB Adjustment

This function allows you to adjust an overall color balance of the copied image by changing the strength of red (R), green (G) and blue (B) at the time of scanning.

• This function is available only in the full color mode.

1 Place paper in the drawer(s).

2

Place the original(s).

3 Press the [IMAGE] button to enter the image menu, and then press the

[RGB ADJUSTMENT] button.

4

4 Press the or button of the color to obtain the desired color balance. Then press the [ENTER] button.

• “0” is the standard setting.

• Pressing the button strengthens the adjusted color, and pressing the button weakens it.

• Select other copy modes as required.

5 Press the [START] button.

Canceling RGB adjustment

Move the indicator of the color whose adjustment you want to cancel its adjustment to 0 by your pressing the or button, and then press the [ENTER] button.

If you want to cancel the adjustment of all colors, press the [DEFAULT] button, and then press the

[ENTER] button.

112

3. One-Touch Adjustment

4

This function allows you to obtain the desired image quality. You can select among 4 modes; “WARM”,

“COOL”, “VIVID” or “CLEAR” in a one-touch operation.

• See Color Guide for the adjustment results.

• This function is available only in the full color mode.

1

Place paper in the drawer(s).

2 Place the original(s).

3

Press the [IMAGE] button to enter the image menu, and then press the

[ONE TOUCH ADJUSTMENT] button.

4

Press the [WARM], [COOL], [VIVID] or [CLEAR] button.

• Select other copy modes as required.

5

Press the [START] button.

113

4.IMAGE ADJUSTMENT

4. Background Adjustment

This function allows you to adjust the density of the original’s background. It avoids the back side of 2sided originals becoming visible on the front side of the original through the copy.

• This mode cannot be used with the automatic copy density mode. (

! P.108)

1 Place paper in the drawer(s).

2

Place the original(s).

3 Press the [IMAGE] button to enter the image menu, and then press the

[BACKGROUND ADJUSTMENT] button.

4

4 Press the [LIGHT] (or [DARK]) button to adjust the density, and then press the [ENTER] button.

• Select other copy modes as required.

5 Press the [START] button.

Canceling the background adjustment

• Press the [DEFAULT] button and then the [ENTER] button.

• Adjust the background level to “0”, and then press the [ENTER] button.

114

5. Sharpness

4

This function allows you to emphasize or blur the outline of the image. When the sharpness level is adjusted to the [SOFT] side, the moire fringes are suppressed. If it is adjusted to the [SHARP] side, the letters and fine lines become sharper.

1 Place paper in the drawer(s).

2

Place the original(s).

3 Press the [IMAGE] button to enter the image menu, and then press the

[SHARPNESS] button.

4 Press the [SOFT] (or [SHARP]) button to adjust the sharpness, and then press the [ENTER] button.

• When the sharpness level is adjusted to the [SOFT] side, the moire fringes are suppressed. If it is adjusted to the [SHARP] side, the letters and fine lines become sharper.

• Select other copy modes as required.

5 Press the [START] button.

Canceling the sharpness adjustment

• Press the [DEFAULT] button and then the [ENTER] button.

• Adjust the sharpness level to “0”, and then press the [ENTER] button.

115

4.IMAGE ADJUSTMENT

6. Twin Color (2-Color) Copy

This function allows you to copy a colored original in 2 specified colors. There are 2 types of twin color copy as follows:

TWIN COLOR SELECTABLE: The black part and the parts other than black in the original are copied separately in 2 colors which have been manually specified.

RED & BLACK: The red part in the original is copied in red and the parts other than red are copied in black and white.

• The color may not be correctly reproduced depending on the originals. In that case, copy them in the full color mode.

TWIN COLOR SELECTABLE

1

Place paper in the drawer(s).

2 Place the original(s).

3

Press the [IMAGE] button to enter the image menu, and then press the

[TWIN COLOR COPY] button.

4

4

Press the [TWIN COLOR SELECTABLE] button.

116

6.Twin Color (2-Color) Copy (Cont.)

5 Select a color for the black part in the original. Press the [CHANGE

BLACK TO] button, and then select the desired color.

4

6 Select a color for the parts other than black in the original. Press the

[SECOND COLOR] button, and then select the desired color.

7 Press the [ENTER] button.

• Select other copy modes as required.

8 Press the [START] button.

117

4.IMAGE ADJUSTMENT

RED & BLACK

1 Place paper in the drawer(s).

2 Place the original(s).

3 Press the [IMAGE] button to enter the image menu, and then press the

[TWIN COLOR COPY] button.

4

4 Press the [RED & BLACK] button.

5 To adjust the red color, press the [ADJUST] button. If you do not change the color balance, press the [ENTER] button and proceed to step 7.

118

6.Twin Color (2-Color) Copy (Cont.)

6 Press the or button of the color to obtain the desired color balance. Then press the [ENTER] button.

4

7 Select other copy modes as required, and then press the [START] button.

119

4.IMAGE ADJUSTMENT

5. USING THE EDITING FUNCTIONS

1. IMAGE SHIFT .................................................................................................................... 121

2. EDGE ERASE.................................................................................................................... 127

3. BOOK CENTER ERASE.................................................................................................... 129

4. DUAL PAGE....................................................................................................................... 131

5. 2IN1 / 4IN1 .........................................................................................................................133

6. MAGAZINE SORT .............................................................................................................136

7. EDITING ............................................................................................................................ 138

• Trimming / Masking .........................................................................................................................138

• Mirror image ....................................................................................................................................141

• Negative/Positive reversal...............................................................................................................142

8. XY ZOOM ..........................................................................................................................143

9. COVER SHEET ................................................................................................................. 145

10.SHEET INSERTION........................................................................................................... 148

11. TIME STAMP ..................................................................................................................... 151

12.PAGE NUMBER.................................................................................................................152

13.JOB BUILD ........................................................................................................................ 154

14.IMAGE DIRECTION........................................................................................................... 158

15.BOOK - TABLET ................................................................................................................160

16.ADF / SADF ....................................................................................................................... 161

5

120

5

1. IMAGE SHIFT

A margin for binding can be created. The following types are available.

1. Created by shifting the original image to either the right or left side (Right or Left margin)

2. Created by shifting the original image to either the upper or lower side (Top or Bottom margin)

3. Created binding margins in the center (inner margin) (Bookbinding margin)

Select this setting when using “Book-type original -> 2-sided copy” (

! P.102).

• The ‘Top or Bottom margin’ can be used in combination with the ‘Right or Left margin’ or the ‘Bookbinding margin’.

• The margin width can be adjusted in 1 mm increments.

1 2

Creating a right or left margin

1 Place paper in the drawer(s).

• When using this mode in bypass copying (

! P.58), be sure to specify the paper size.

2 Place the original(s).

3 Press the [EDIT] button to enter the edit menu, and then press the

[IMAGE SHIFT] button.

121

5.USING THE EDITING FUNCTIONS

4 Press the [LEFT] (or [RIGHT]) button.

5 Adjust the margin width by pressing the [2 mm] or [100 mm] button, and then press the [ENTER] button.

5

• The default width of the margin is 7 mm (0.276").

• In duplex copying, margins on the back are created on the other side of those in the front. (

! P.97 “5.Duplex

Copying”)

6 Press the [ENTER] button.

• Select other copy modes as required.

7 Press the [START] button.

122

1.IMAGE SHIFT (Cont.)

5

Creating a top or bottom margin

1 Place paper in the drawer(s).

• When using this mode in bypass copying (

! P.58), be sure to specify the paper size.

2 Place the original(s).

3 Press the [EDIT] button to enter the edit menu, and then press the

[IMAGE SHIFT] button.

4 Press the [TOP] (or [BOTTOM]) button.

123

5.USING THE EDITING FUNCTIONS

5 Adjust the margin width by pressing the [2 mm] or [100 mm] button, and then press the [ENTER] button.

• The default width of the margin is 7 mm (0.276").

6 Press the [ENTER] button.

• Select other copy modes as required.

7 Press the [START] button.

5

124

5

1.IMAGE SHIFT (Cont.)

Creating a bookbinding margin

This is used when setting “Book-type original -> 2-sided copy” (

! P.102) in duplex copying. The margin is

created in the center (inner margin).

• Acceptable paper sizes for this function is LT only.

1 Press the [EDIT] button to enter the edit menu, and then press the

[IMAGE SHIFT] button.

2 Press the [BOOK] button.

3 Adjust the margin width by pressing the [2 mm] or [30 mm] button, and then press the [ENTER] button.

• The default width of the margin is 14 mm (0.551").

125

5.USING THE EDITING FUNCTIONS

4 Press the [ENTER] button.

• Set “Book-type original -> 2-sided copy” (

! P.102) in duplex copying as well.

5

126

2. EDGE ERASE

If the original has a dirty or torn edge, it may be reproduced as a black stain on the copy. In that case, set the edge erase. A white border is created along the edges of the copy, eliminating those black stains.

• This function is available only in the case of standard-size originals.

• The width of the edge erase margin can be adjusted in 1 mm increments.

5

1 Place paper in the drawer(s).

• When using this mode in bypass copying (

! P.58), be sure to specify the paper size.

2 Place the original(s).

3 Press the [EDIT] button to enter the edit menu, and then press the

[EDGE ERASE] button.

127

5.USING THE EDITING FUNCTIONS

4 Adjust the width by pressing the [2 mm] or [50 mm] button, and then press the [ENTER] button.

• The default width of the white border is 5 mm (0.197").

• Select other copy modes as required.

5 Press the [START] button.

5

128

3. BOOK CENTER ERASE

This function allows you to erase the shadow in the center of a book original.

1. Before book center erase is set

2. After book center erase is set

The width of the book center erase margin can be adjusted in 1 mm increments.

1 2

5

1

Place paper in the drawer(s).

• When using this mode in bypass copying (

! P.58), be sure to specify the paper size.

2

Press the drawer button representing the desired paper size on the touch panel.

3 Press the [EDIT] button to enter the edit menu, and then press the

[BOOK CENTER ERASE] button.

129

5.USING THE EDITING FUNCTIONS

4 Adjust the width by pressing the [2 mm] or [50 mm] button, and then press the [ENTER] button.

• The default width of the erase margin is 10 mm (0.393").

• Select other copy modes as required.

5 Place a book original on the original glass.

• Align its center with the yellow guide line near the center of the original glass.

Do not place heavy objects (9 lb. or more) on the original glass and do not press on it with force. Breaking the glass could injure you.

6

Press the [START] button.

5

130

4. DUAL PAGE

This function allows the facing pages of a book or magazine to be copied page by page onto 2 separate sheets of paper or duplex-copied on one sheet. It is not necessary to move the original on the glass. You can also place a pair of LT sized originals side by side and copy them on separate sheets of paper.

• Acceptable paper sizes for this function is LT only.

5

-12-13-12-

-13-

1 Place paper in the drawer(s).

2 Press the [EDIT] button to enter the edit menu, and then the [DUAL

PAGE] button.

3 Press the [1 SIDE] (or [2 SIDE]) button.

1 SIDE: Making copies of the facing pages on 2 separate sheets of paper page by page

2 SIDE: Making duplex copies of them on one sheet

• The yellow indicator line for placing a book moves near the center of the original glass.

• If you need a binding margin, set the right or left margin. (

! P.121 “Creating a right or left margin”)

131

5.USING THE EDITING FUNCTIONS

4 Press the [BASIC] button to enter the basic menu, and then select the copy size (LT).

• When using this mode in bypass copying (

! P.58), be sure to specify the paper size.

• Select other copy modes as required.

5 Place the first page(s) to be copied on the glass, and then press the [START] button.

• Center the book on the yellow indicator line with the bottom

toward you. (

! P.46 “Book-type originals”)

Do not place heavy objects (9 lb. or more) on the original glass and do not press on it with force. Breaking the glass could injure you.

6 Turn to the next page, set the book again, and then press the [START] button.

• Repeat this step until all the originals have finished being scanned.

7 After all the originals have finished being scanned, press the [FIN-

ISHED] button.

5

• Press the [COPY FINAL PAGE] button if the last original is a 1-sided page.

132

5. 2IN1 / 4IN1

This feature allows multiple originals to be reduced and copied onto a single sheet of paper. There are 2 modes: 2IN1 copying, where 2 originals are copied onto a single sheet, and 4IN1 copying, where 4 originals are copied onto a single sheet. In addition, duplex 2IN1 / 4IN1 modes are available, where four/eight originals can be copied to 2 sides of a single sheet of paper.

2IN1

5

4IN1

2IN1 DUPLEX (a: Side 1, b: Side 2)

• When a copy is turned with the line as a pivot, originals are printed on Side 2 (back face) as shown.

a a b b

4IN1 DUPLEX (a: Side 1, b: Side 2)

• When a copy is turned with the line as a pivot, originals are printed on Side 2 (back face) as shown.

a b

133

5.USING THE EDITING FUNCTIONS

1 Place paper in the drawer(s).

• When using this mode in bypass copying (

! P.58), be sure to specify the paper size.

• If the paper size is not changed, paper of the same size as the original is selected.

• To make copies on paper which is not the same size as the original, press the [ZOOM] button on the basic menu to enter the following menu, select the desired paper size and press the [AMS] button.

2 Place the original(s).

3

Press the [EDIT] button to enter the edit menu, and then press the

[2IN1 / 4IN1] button.

5

4

Select the type of image combination.

134

5.2IN1 / 4IN1 (Cont.)

5 Press the [1 SIDE] (or [2 SIDE]) button.

5

• Select other copy modes as required.

6 Press the [START] button.

• When the Reversing Automatic Document Feeder (optional) is used, the original is scanned and copying starts.

• When the original is placed on the original glass, perform steps 7 and 8.

7 Place the next original, and press the [START] button.

• Data scanning of this original starts.

• The next original will also be scanned in the same manner when you press the [YES] button on the touch panel, and then press the [START] button on the control panel.

• Repeat this step until all the originals have finished being scanned.

8 After all the originals have finished being scanned, press the [FIN-

ISHED] button.

• Copying starts.

135

5.USING THE EDITING FUNCTIONS

6. MAGAZINE SORT

This function allows 1-sided originals to be copied and sorted so that they can be folded and bound along a center line like typical magazines or booklets.

Example of copying a 12-page document

1

2

3

6

4

2

7

9

11

12

When placing a portrait originals horizontal to you in the magazine sort mode, be sure to set the correct

direction of the originals. (

! P.158 “14.IMAGE DIRECTION”)

Using this function in combination with the Saddle Stitch Finisher (optional) makes copies automatically folded in half and stapled along their center line.

Example of copying with the Saddle Stitch Finisher (optional)

5

1

2

3

6 7

12

The Magazine sort function has 2 procedures; operating from the basic menu and operating from the edit menu. When operating from the edit menu, the margin width can be adjusted.

To operate from the basic menu, see

! P.90 “Magazine sort & saddle stitch mode (booklet mode)”.

1 Place paper in the drawer(s).

• When using the Saddle Stitch Finisher, LD, LG, LT-R, A3, A4-R and B4 are available.

2 Select the paper type.

• For drawer feeding, see

! P.73 “Manual paper selection”.

• For bypass feeding, see

! P.58 “3.Bypass Copying”.

3 Place the original(s).

136

6.MAGAZINE SORT (Cont.)

4 Press the [EDIT] button to enter the edit menu, and then press the

[MAGAZINE SORT] button.

5

5 Set the saddle-stitch and the binding margin and press the [ENTER] button.

• To staple the center line using the Saddle Stitch Finisher (optional), press the [STAPLE ON] button. For the

maximum number of sheets that can be stapled, see

! P.92 “Available conditions for saddle stitching”.

• To adjust the width, press the [2 mm] or [30 mm] button.

• The default width of the margin is 2 mm (0.08").

• The margin width can be adjusted in 1 mm increments.

• Select other copy modes as required.

6 Press the [START] button.

137

5.USING THE EDITING FUNCTIONS

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents