DJI GS PRO User Manual
: Tap to delete the last point.
: Tap to finish after setting all the required points.
Aircraft (Record Altitude): This method can only be used for Waypoint Flight missions. The instructions are the same as “Aircraft” above. In addition, both position and altitude will be recorded. When performing the mission, the aircraft will fly the preset position and altitude.
The flight area will be generated according to the order the points were set.
The area generated according to the order that the points were set cannot intersect otherwise a flight area cannot be generated. DJI GS Pro will decide if points can be used to generate a flight area. If not, the “Finish” button will be grayed out and cannot be tapped.
4. Parameter Settings
Set each item in the parameter setting list and tap the “Save” button in the top left corner of the screen when complete. Refer to the Parameter Settings Introduction for more details.
Perform Mission
Safety Instructions
Please pay careful attention when flying and shooting in 3D Map POI. Vertical and Circle (below) are the two modes in Flight Course Mode settings.
1. In Circle and Vertical mode, the aircraft will fly in a straight path between waypoints, although the actual distance between the aircraft and the structure may sometimes be shorter than the preset flight radius. During Capture at Equal Distance/Time Interval mode, the aircraft will fly along a parabola and the distance to the shooting target may be longer than the preset radius, so please make sure the surrounding area is open and large enough to avoid collision risks. To ensure flight safety, operators on the ground should move along with the aircraft to maintain line of sight as the aircraft flies around the structure.
2. In Vertical mode, the aircraft will fly up and down many times at a relatively low speed (1~4 m/ s, although speed varies from different aircraft modes), which will lead to a longer shooting time and faster consumption of the battery level.
3. When resuming operations in Circle or Vertical mode, the aircraft will first ascend directly to a height equal to the previous waypoint, than fly towards it. To avoid collision risks, be sure there are no ceilings or buildings above the aircraft.
Pre-flight Checklist
Choose a mission in the mission list, tap “Edit” then tap “Prepare for Flight” in the top right corner of the screen. Check and adjust the aircraft according to the checklist that appears until all items are green, indicating that takeoff is permitted. Items in yellow require adjustment but the aircraft can take off without doing so. Only flying when all items are green is highly recommended.
©
2017 DJI All Rights Reserved.
9
DJI GS PRO User Manual
Start to Fly
Tap “Start to fly” at the bottom of the checklist when ready. An aircraft’s actions will vary depending on its mission. The Aircraft Status Bar will show the current aircraft status, mission progress, etc.
N
Please enter the fence
Speed
0.1M/S
LAT: 35.635709
LON: 139.788572
Height
54.9M
Virtual Fence
After starting, if the aircraft’s latitude, longitude or altitude is outside of the fence boundaries, there will be visual and audio prompts on the iPad. The Virtual Fence will be disabled at this time and the aircraft can be flown freely. The Virtual Fence will be automatically enabled when the aircraft enters fence boundaries. Once inside, if the aircraft approaches the boundaries of the fence, it will slow to a hover and audio prompts will sound from the iPad.
3D Map / Waypoint Flight
After starting, the aircraft will fly to the start point automatically. In 3D Map POI, the altitude of the start point will be the preset maximum altitude.
Pause Mission
During 3D Map or Waypoint Flight missions, tap the “Pause Mission” button on the top right corner of the screen to pause the mission. The aircraft will hover in place and record the last performed waypoint. The aircraft can then be flown freely and a menu will pop up with additional control options.
Resume from Last Stopped Point: The aircraft will continue the mission from the point where recording stopped.
Start Over: The aircraft will fly to the start point and restart the mission.
Cancel Current Mission: The aircraft will stop and exit from the current mission. The mission cannot be continued.
Back to Mission List: Back to the mission list. To check this menu again, select the required mission and tap edit then tap “Resume Mission”.
Special Cases
1. During a Virtual Fence mission, if the aircraft flies out of the fence due to external forces i.e. strong wind, a prompt will appear in the Aircraft Status Bar, an audio prompt will sound from the iPad, and the fence will be disabled. Users must stop the mission and restart it.
2. During a Virtual Fence mission if the flight mode switch on the remote controller is toggled, the fence will be disabled immediately. The aircraft will stop and exit from the current mission, a prompt will appear in the Aircraft Status Bar, and an audio prompt will sound from the iPad.
10
©
2017 DJI All Rights Reserved.
DJI GS PRO User Manual
3. During any mission, the aircraft will exit from its mission and enter a normal flight mode if positioning is not available due to a weak GNSS signal. Users can choose to continue the mission if the signal is strong. When continuing, the aircraft will continue from its last recorded point.
4. Low Battery Level Warning: When the battery level or voltage is lower than the value pre-set, an audio prompt will sound from the remote controller. After a few seconds, the aircraft will pause the mission and begin RTH. Users can cancel the RTH by pressing the Smart RTH button on the remote controller. The mission can be continued and the aircraft will continue the mission from the point where recording stopped after replacing battery.
5. Critically Low Battery Level Warning: When the battery level or voltage is lower than the value pre-set, an audio prompt will sound from the remote controller. The aircraft will pause the mission and land automatically. The mission can be continued and the aircraft will continue the mission from the point where recording stopped after replacing battery.
Mission Complete
After finishing a Virtual Fence mission, tap “End Mission” in the top right corner of the screen. After a 3D Map or Waypoint Flight mission is complete, the aircraft will perform the pre-set “End-Mission
Action”. After the action, the aircraft can be controlled freely.
©
2017 DJI All Rights Reserved.
11
