22
OWNER’S MANUAL
Shift Options
Several menus are available on the mixer to set preferences. Available menus are indicated with a gray up
SHIFT button and then press the desired menu key.
Note: the Shift button may be labeled as the Delete button on older Sixty-Two Mixers.
Ext. Insert Options Menu
This menu sets the sensitivity of the external analog insert to +4 dBu or -10 dBV. Use the
+4 dBu setting when a device operating at
4 Vrms or more is connected to the external
SHIFT
EXT. INSERT
EXTERNAL INSERT
… +4 dBu
-10 dBV
FlexFX Loop. Use the -10 dBV setting when connecting lower voltage devices with RCA connectors. The overall loop gain remains unchanged for both settings. Push the
BEAT joystick up/down to select the desired setting then press the joystick in to keep the selection. Press any effect button or the
SHIFT button to exit the menu.
Filter Effect Options Menu
The Filter menu allows choosing one of four filter types. Move the BEAT joystick up/down to select the desired filter type then press the joystick in to keep the selection. The Low-sync
SHIFT
FILTER
LP FILTER LO
… LP FILTER HI
HP FILTER LO
Filters sync to BPM at the low point of the sweep, and the High-sync Filters sync to BPM
HP FILTER LO
at the high point of the sweep. Press any effect button or the SHIFT button to exit the menu.
• Low-pass Filter Low-sync.
• Low-pass Filter High-sync.
• High-pass Filter Low-sync.
• High-pass Filter High-sync.
Flanger Effect Options Menu
The Flanger menu allows the choice of positive or negative feedback. Move the BEAT joystick up/down to highlight the desired feedback type then press the joystick in to keep the selection. Press any effect button or the SHIFT button to exit the menu.
SHIFT
FLANGER
FLANGER -Fb
… FLANGER +Fb
Echo Effect Options Menu
The Echo menu allows selection of four echo effects:
• Echo.
• Echo with high-pass filter.
SHIFT
ECHO
ECHO
… ECHO 81 Hz
DUCKECHO 75 Hz
• Duck Echo.
• Hold Echo with high-pass filter.
HD ECHO 120 Hz
Move the BEAT joystick up/down to highlight the desired echo type then press the joystick in to keep the selection. For the three high-pass Echo effects, the filter corner frequency is adjusted by highlighting the desired effect and rotating the TIME encoder. Press any effect button or the
SHIFT button to exit the menu.
SIXTY-TWO
23
OWNER’S MANUAL
Deck 1-2 Channel Options Menu
A menu is available for each deck input channel.
Press and hold the SHIFT button then press the
CUE button of an input channel. This menu allows
SHIFT
you to select 1 of 2 USB record sources and set the resonance of the Filter. Record options are:
• Pre-selector PH/CD 1 input source (required for DVS).
• Pre-selector PH/CD 2 input source.
CUE
… REC PH/CD-1
REC PH/CD-2
FILTER RESONANCE
Move the Beat joystick up/down to highlight the desired record source, then press the joystick in to keep the selection. The PH/CD input must be selected for DVS operation.
Resonance is shown on the bar graph, and adjusted with the TIME encoder.
High resonance results in a zippy whistle sound with high peaking of the signal at the corner frequency. High resonance is typically used as an effect. A low resonance settings has no peaking and is typically used for mixing. Press any effect button or the SHIFT button to exit the menu.
Mic Option Menu
Press and hold the SHIFT button then press the
HOLD button to view the Mic option menu.
• Record the Main Mix to USB.
SHIFT
CLEAN FEED
OVER
RECORD MAIN
RECORD MIC
CLEAN FEED
• Record only the Mic to USB.
• Clean Feed:
When Clean Feed is selected, the microphone signal is sent directly to the Main Out and is not present in the USB Main Record, Booth Out or Session Out. When set for Clean Feed, the Mic cannot be assigned to FlexFx. If the Mic FlexFx is pressed, the button will blink off to dim.
Mic Bypass Mode
All controls on the mixer are MIDI mappable, including the Mic sections. If you do not use the Mic sections, you can independently
SHIFT
BYPASS
ON
bypass the controls so they do not affect audio, and only output their MIDI changes. This allows you to map the Mic controls to functions in software, such as effects, and not have to worry about introducing noise in your mix from a floating
Mic input. To toggle Mic Bypass Mode, hold the SHIFT button and press the Mic ON button to bypass.
The button will start flashing lightly, indicating those audio controls are now bypassed and are only outputting MIDI changes. The Mic On and FlexFX buttons, as well as the Level, Pan, and Tone controls are affected by this mode. While bypassed, the FlexFX and Mic On buttons will flash with momentary button presses, but the LED state cannot be set from software like the side strip controls. Holding the
SHIFT button and pressing the Mic ON button again will exit Mic Bypass Mode, returning the Mic section to regular operation. The Mic ON button will return to the “off” state. Be sure to reset the Level, Pan, and Tone controls to appropriate values before switching the Mic back on.
Headphone Tone Control
Press and hold the SHIFT button then press the
SPLIT CUE button to call the headphone menu.
Turn the Time encoder up or down to adjust the
SHIFT
SPLIT CUE
HEADPHONE TONE
LOW HIGH
tone. For larger steps, you can press the joystick left/right. When the bar-graph is in the center, the response is flat. As the control is moved toward Low, low frequencies are boosted and high frequencies are cut. As the bar-graph moves toward High, high frequencies are boosted and low frequencies are cut.
SIXTY-TWO
OWNER’S MANUAL
Mixer Shift Functions
In addition to the menu selections, the Shift button also accesses alternate functions for other buttons.
MIDI Start/Stop
Hold the SHIFT button and press TAP to toggle
MIDI Start/Stop messages. MIDI Start is a system real time message instructing devices to start playing a sequence. MIDI Stop tells devices to stop playing the sequence.
Nudge
Hold the SHIFT button and use the BEAT joystick to “Nudge” the outgoing MIDI beat clock BPM up or down. MIDI beat clock is a system real time message sent 24 times per quarter note.
SHIFT
SHIFT
START / STOP
TAP
BPM Adjust
Hold the SHIFT button and turn the TIME encoder to adjust the BPM to a specific value.
SHIFT
Sync
Hold the SHIFT button and press SYNC to turn Sync on for a Deck. If Sync is already on, pressing Shift/Sync again re-syncs the Deck. Press SHIFT and SYNC OFF to turn Sync off. See Sync in the Serato DJ manual.
LOOP
SYNC
IN
ROLL
SYNC OFF
OUT
Slip
Hold the SHIFT button and press SLIP to toggle Slip On or Off. When Slip Mode is active you can manipulate the audio as normal (e.g., Scratch, Loop, Cues etc.).
However, once you have finished, playback is returned to where it would be if you had not manipulated the audio. See Slip in the
Serato DJ manual.
SAVE
SLIP
SHIFT
LOOP
24
SIXTY-TWO