advertisement
7458en.book 23 ページ 2004年5月14日 金曜日 午前10時47分
To record programmes from satellite receiver by RGB signals
Preparation
≥Change the settings in the SETUP menu as follows (
➡page 43).
–“AV2 Input”: “RGB (Not NTSC)”
–“AV2 Connection”: “Normal”
Follow the steps indicated for manually programming timer recordings
(
➡page 22).
≥Make sure you connect to the “TV Scart terminal” of a Sky Digital
STB with a 21-pin Scart lead.
≥Set your Sky Digital STB to output “RGB” signals.
≥After setting the Personal Planner programmes as required, Sky
Digital STB must be left on (not set to standby) to ensure continuous output of RGB signals.
Check, change or delete a programme
≥Even when the unit is turned off, you can display the timer recording list by pressing [PROG/CHECK].
Press [PROG/CHECK].
Icons
[ This programme is currently recording.
W The times overlap those in another programme.
Recording of the programme with the later start time starts when the earlier programme finishes recording.
F The disc was full so the programme failed to record.
The material was copy-protected so it was not recorded.
X The programme did not complete recording because the disc is dirty or some other reason.
Timer programmes set to Auto Renewal Recording.
Titles that have been rerouted to the HDD
(Displayed while recording.)
Recording drive: HDD
Recording drive: DVD
TIMER
RECORDING
No.
Name
Remain HDD 30:24 SP DVD 1:58 SP
Date Start Stop
New Timer Programme
12:56:00 15. 7. TUE
Mode
PDC
HDD
DVD
12:55:00 15. 7. TUE
SELECT
ENTER
RETURN
Press ENTER to store new programme.
Message displayed in the “Disc space” line
OK:
Displayed if the recording can fit in the remaining space.
> (Date): For recordings made daily or weekly, the display will show until when recordings can be made (up
! :
to a maximum of one month from the present time) based on the time remaining on the disc.
It may not be possible to record because:
≥there is not enough space left
≥the number of possible titles has reached its maximum.
Relief:
Timer programmes that will be relief recorded to the HDD.
∫ To change a programme
Press [
3, 4] to select the programme and press [ENTER].
(
➡page 22, step 3)
∫ To delete a programme
Press [
3, 4] to select the programme and press [¢ CANCEL].
∫ To exit the timer recording list
Press [PROG/CHECK].
∫ To put the unit on timer recording standby
Press [
F TIMER].
“
F” lights on the unit’s display to indicate timer recording standby has been activated.
≥Programmes that failed to record are displayed gray. They are automatically deleted from the timer recording list at 4 a.m. two days later.
Linked timer recordings with external equipment (EXT LINK)
[HDD] [RAM] [DVD-R]
If an external equipment (for example a satellite receiver) with a timer function is connected to the AV2 terminal of this unit by a
21-pin Scart lead (
➡page 7, 10), it is possible to control the recording of the unit with the equipment.
Preparation
≥Change the “Ext Link” in the SETUP menu to match the connected equipment (
➡page 43).
≥Timer programming has to be done on the external equipment and switch to the timer recording standby mode. Refer to the equipment’s operating instructions.
Press [EXT LINK].
The unit turns off and switches to the recording standby mode.
≥Recording begins when a signal is received from the connected equipment.
≥As long as a video picture is being transmitted by the external equipment, the unit will record it.
When the following message appears on the television screen, press
[
2, 1] to select “Yes” (continue recording the current programme) or “Cancel” (cancel recording) and press [ENTER].
DVD now recording this programme.
Yes Cancel
ENTER
RETURN
[Note]
It is not possible to use EXT LINK function for timer recording of
RGB signals from Sky Digital STB (
➡left, To record programmes from satellite receiver by RGB signals).
To record programmes from a satellite receiver using the “Sky Personal Planner” function
Change the settings in the SETUP menu as follows (
➡page 43).
–“AV2 Input”: “Video”
–“AV2 Connection”: “Normal”
–“Ext Link”: “Ext Link 1”
≥Make sure you connect to the “VCR Scart terminal” of a Sky Digital
STB with a 21-pin Scart lead.
To cancel the external control
Press [EXT LINK] to stop recording or to cancel linked timer recording standby.
≥You can also press and hold [∫] on the main unit for more than 3 seconds to stop recording.
≥In order to prevent accidental operation, press [EXT LINK] to cancel the setting after recording is finished.
For your reference
≥The video being recorded automatically appears on the television when connected to this unit’s AV1 terminal with the 21-pin Scart lead.
≥This function does not work with some equipment. Refer to the equipment’s operating instructions.
≥The beginnings of recordings may not be recorded correctly in some cases.
≥When “Ext Link” is set to “Ext Link 2”, this function does not work if the input signal is NTSC system.
RQT7458
23
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 2 Caution for AC Mains Lead
- 3 Useful features
- 4 Accessories
- 4 The remote control
- 5 Control reference guide
- 6 Connection
- 11 Channel reception settings
- 14 remote control
- 14 To enjoy progressive video
- 16 HDD and Disc information
- 18 Recording television programmes
- 19 Recording modes and approximate recording times
- 19 Direct TV Recording
- 19 Playing while you are recording
- 20 Flexible Recording
- 20 Recording from an external equipment
- 21 Timer recording
- 21 Using VIDEO Plus+ number to make timer recordings
- 22 Manually programming timer recordings
- 23 by RGB signals
- 23 Check, change or delete a programme
- 23 Linked timer recordings with external equipment (EXT LINK)
- 24 Playing discs
- 25 Operations during play
- 26 Editing operations during play
- 26 Changing audio
- 27 Using menus to play MP
- 28 On-screen menus
- 29 Status messages
- 30 Editing titles/chapters
- 30 Editing titles/chapters and playing chapters
- 31 Title operations
- 31 Chapter operations
- 32 Creating, editing and playing play lists
- 32 Creating play lists
- 33 Editing and playing play lists/chapters
- 33 Play list operations
- 33 Chapter operations
- 34 Entering text
- 35 Transferring (dubbing) titles or play lists
- 36 One Touch Transfer (dubbing)
- 36 Transferring (dubbing) using the transferring (dubbing) list
- 37 Transferring (dubbing) a finalized DVD-R
- 38 FUNCTIONS window
- 38 DISC MANAGEMENT
- 39 Disc Name
- 39 Disc Protection
- 39 Format Disc
- 39 Top Menu
- 39 Auto-Play Select
- 39 Finalize
- 40 Changing the unit’s settings
- 40 Common procedures
- 40 Summary of settings
- 44 Tuning
- 45 TV System
- 46 Clock settings
- 46 Child Lock
- 47 Specifications
- 47 Safety precautions
- 48 Glossary
- 50 Frequently asked questions
- 51 Error messages
- 52 Troubleshooting guide
- 55 Maintenance