EXPLANATIONS FOR EACH FUNCTION. ERNITEC DigiOpG2 EDNS3000 Series

Add to My manuals
51 Pages

advertisement

EXPLANATIONS FOR EACH FUNCTION. ERNITEC DigiOpG2 EDNS3000 Series | Manualzz

DigiOpG2 Digital Video Recorder

2.

Explanations for each function

2.1

Front Panel

The buttons on both the front panel of the EDNS-3000 and IR Remote Controller have the same functions. Each button can activate different functions. The buttons on the front panel of EDNS-3000 may be different in shape than the remote controller buttons, but the IR Remote Controller can also control the functions controlled by the front panel of the EDNS-

3000.

Page 6

No.

1

2

3

4

5

6

Buttons

Power Button

Power LED

HDD LED

Network LED

Sensor LED

Audio LED

7

SCR MODE

CH1-8/CH9-16

8

9

Multiple Screen Mode

Buttons (Arrow

Buttons)

PAN/TILT/

ZOOM/FOCUS/ IRIS

10 SETUP

11 SEARCH

12 Jog/Shuttle

13 USB Port

14 BACKUP Button

15 EVENT Button

16 RETURN Button

17 OSD Button

18 P/T/Z Button

19 SEQ Button

20 ENTER Button

21

Fast Playback

Backwards

22

Playback Backward

Frame by Frame

23 Playback

24

Playback Forward

Frame by Frame

25 Fast Playback Forward

Functions

Use to turn the Power On/Off.

Shows Power On/Off status of the system (GREEN: Working, RED: Stand-by).

Shows if the camera image is being stored into or retrieved from the HDD (Hard Disk

Drive).

LED is lit while the network client(s) (RemoteAgent) is connected to the system.

LED is lit when alarm sensor is activated.

LED is lit while audio data from audio input device is being recorded.

Button to select modes of the arrow buttons.

Whenever the button is pressed, the screen will change to

[1~8 channel mode], [9~16channel mode], or [multiple(split) screen mode].

The default mode is [multiple(split) screen mode].

Buttons to select the multiple screen mode as printed, or for use as cursor keys.

Button for Camera PAN/TILT/ZOOM/FOCUS/IRIS functions.

Menu to set user environment of the system.

Search recorded image.

Jog (inner dial): playback frame by frame.

Shuttle (outer dial): Speed up the playback speed of the image (1~32X).

USB interface port to connect external storage equipment.

Button to backup recorded image data.

Shows system’s event information in order of time and brings up event viewer to search image of the corresponding time.

Use to exit from the setting menu or to cancel setting value.

Button to control the OSD (On-Screen Display).

For using P/T/Z functions of the camera.

Automatic time sequencing for monitor images.

Use to enter detail menu, go into the next stage, select or set value.

Fast playback the recorded images backwards in the playback mode.

Playback the recorded images frame by frame backwards in the playback mode

(playback only I-Frame)

Playback recorded images from playback menu.

Playback the recorded images frame-by-frame forward in the playback mode.

Fast playback the recorded images forward in the playback mode.

3040-00052

DigiOpG2 Digital Video Recorder

2.1.1.

Power Button

When the power cable of the product is connected, press this button to turn power on or off.

2.1.2.

Power LED

LED to show the power input and status of the system. The LED is red when the system is in stand-by position, but is green when the system is working and power is being supplied.

2.1.3.

HDD LED

LED is blue when the camera image is being stored into or retrieved from the HDD. So, even though the system is continuously recording, the HDD LED is only lit when actual data is recorded in the HDD. Usually, the LED will be flickering, and this is normal.

2.1.4.

Network LED

LED is blue when the system is connected to any network client (RemoteAgent). Light is automatically out when all clients are disconnected.

2.1.5.

Sensor LED

LED is lit when the system has any activated sensor input.

2.1.6.

Audio LED

LED is lit when audio data from audio input device is being recorded. Even though the audio input device is properly connected, it will not light up when audio is not recorded.

2.1.7.

SCR MODE or CH1-8 / CH9-16

Use to see the images on the monitor as multiple screens. Whenever this button is pressed, [1-8] ( ) group icon, [9-16] group icon ( ), or no icon will be seen on the lower right end of the monitor. When ( arrow button will be used to select no. 1~8 images. Thus, when icon (

) is indicated on the screen, the

) appears on the screen, the arrow button will be used to select images from no. 9~16. If the icon is not indicated, the arrow button will be use to select multiple screens (

As a default mode, arrow button will be used to select multiple screens.

).

Note

In case of IR Remote Controller, direction (number) key will be used to input channel no. 1~16. If necessary, select split screen mode by pressing [SCR MODE] button on the IR Remote Controller.

2.1.8.

Select Multiple Screen (Arrow Button)

Select each arrow button and the corresponding multiple screens will appear. Up, down, left, right arrow buttons are used to move the cursor to “Setting” mode and are also used to increase/decrease the setting value. Furthermore, they are used to operate camera PAN/TILT Movement, ZOOM IN/OUT, FOCUS FAR/NEAR.

Page 7

3040-00052

DigiOpG2 Digital Video Recorder

2.1.9.

PAN/TILT/ZOOM/ FOCUS/IRIS

Press this button to control PAN/TILT/ZOOM/FOCUS/IRIS value in sequence. This is when PTZ driver has been installed in the camera.

2.1.10.

SETUP

Set the environment of the EDNS-3000 series according to the user requirement.

2.1.11.

SEARCH

Search the recorded image by date and time. Refer to “Recording Image Playback Mode” for detail image searching method.

2.1.12.

Jog / Shuttle

Jog / Shuttle dial is used to playback recording images. The inner dial is called Jog and the outer dial is called Shuttle. The

Jog/Shuttle dial has two kinds of functions. The Jog is used to find the recording image frame by frame. Turn the Jog dial clockwise or anti-clockwise (only I-Frame is playback during anti-clockwise) to see the image frame by frame during pause state. The Shuttle is used to speed up the playback speed of images by clockwise or anti-clockwise. Playback speed is indicated as x2, x4, x8, x16, x32 on the lower end of the screen.

2.1.13.

USB Port

Use to backup recorded images of the EDNS-3000 series by using USB storage device. System software upgrade is possible with USB storage device.

Note

Refer to “Image Backup” for detailed explanation of USB storage devices supported by EDNS-3000 series.

2.1.14.

BACKUP Button

Use to back up images recorded in the HDD to a supported storage device. When this button is pressed, the information from the backup device connected to EDNS-3000 series (ex. CD-RW drive) will be indicated on the screen.

Refer to “Image Backup” for detailed information about backup.

2.1.15.

EVENT Button

Shows system setting changes, alarms, etc., by the order of time and brings up event viewer to search image of the corresponding time. Refer to “Event Search” for further details.

.

2.1.16.

RETURN Button

Use to cancel the password just typed at the setting menu or to return to previous menu.

2.1.17.

OSD Button

OSD will initially be displayed on the screen. When the [OSD] button is clicked once, the OSD will disappear. Click [OSD] button again and the text will reappear.

2.1.18.

P/T/Z Button

Click [P/T/Z] button and an icon will appear on the lower right end of the screen image to show P/T/Z status. This is when

P/T/Z driver has been installed.

2.1.19.

SEQ Button

Press [SEQ] button and screen will automatically change. Refer to “Settings” for automatic sequencing interval (does not work on 16 split screen mode).

2.1.20.

ENTER Button

The [Enter] button is used to go into the next stage, select value, or setting.

Page 8

3040-00052

advertisement

Related manuals