Real time Live Mode. ERNITEC DigiOpG2 EDNS3000 Series

Add to My manuals
51 Pages

advertisement

Real time Live Mode. ERNITEC DigiOpG2 EDNS3000 Series | Manualzz

DigiOpG2 Digital Video Recorder

4.2

Real time Live Mode

Real time live image can be seen after power up.

Note

Both the IR Remote Controller and the front panel button can be used in EDNS-3000 series.

4.2.1.

Screen configuration

1

Page 17

2

Above is the typical real time mode screen. Press [OSD] button on the front panel or IR Remote Controller to control the display of OSD. Whenever the button is pressed, the display of OSD will toggle between appearance and disappearance.

The following is the explanation of each item displayed on the screen from single screen to 16 split screen.

1.

Channel Name: Shows camera title of the channel. Refer to “Setting-> Camera -Title” for how to set and change camera title.

2.

Date and Time: Indicates present date and time of the system. When the recorded data is playback, indicated date and time will be those of the recorded image currently displayed.

3040-00052

DigiOpG2 Digital Video Recorder

4.2.2.

Single screen mode

To see an individual screen, press the [SCR MODE] button on the front panel or IR Remote Controller. Single screen mode must be selected to hear sound from the audio device that is connected to the system, or to see the recorded image.

Press the arrow button on the front panel to change channels.

Note

If split screen mode is selected when an arrow key is pressed, press the [SCR MODE] button.

Press the number button in the IR Remote Controller and the corresponding channel image can be seen. For example, the following image is seen when number 2 is pressed.

Page 18

Note

Check connection status of the camera BNC cable or monitor output cable on the rear panel when image of the monitor cannot be seen.

3040-00052

DigiOpG2 Digital Video Recorder

4.2.3.

Split Screen Mode

In the EDNS-3000 series, the user can see several camera images in various multiple screen formats. Press each button and the corresponding images will be seen in split screen mode.

Note

To see split screens, press the [SCR Mode] on the front panel or IR Remote Controller.

To see the camera image in various split modes, press corresponding arrow buttons. The pictures below correspond to the buttons on the front panel and IR Remote Controller.

Page 19

Button

Front Panel Arrow Button

Multiple Screen Button

IR Remote Controller Number Button

Multiple Screen

1 Screen 4 Screens

6 Screens

9 Screens

13

Screens

8 Screens

10

Screens

16

Screens

3040-00052

DigiOpG2 Digital Video Recorder

4.2.4.

See Operating Status

In real time live mode, icons or messages will be indicated on the screen to notify the system mode or status.

Below are the icon categories, which are indicated on the monitor.

Fast Backward Playback

Playback Backward Frame by

Frame

Pause

Playback

Fast Forward Playback

Playback Forward Frame by

Frame

Alarm

Direction Key

Select Images from No. 1~8

Channels

Select Images from No. 9~16

Channels.

Split screens

Zoom (In/Out)

Focus

Iris

Automatic Screen

Sequence

P/T/Z Controller Activates

Note

When an alarm occurs in the connected channel, the [Alarm] icon will appear on the right bottom side of the screen and “Channel Name” will be indicated in red. The alarm icon will disappear, but the channel number will remain in red for a while when the user enters setup menu, or tries to backup during alarm.

The number buttons on the IR Remote Controller can be used as direction keys.

While [Direction Key] icon is being displayed, the number keys on IR Remote Controller can be used as arrow keys.

When IR Remote Controller is used for P/T/Z control, press [P/T/Z] button to display [P/T/Z] icon and, then, press

[SCR/CH] button to display [Direction Key] icon.

Page 20

3040-00052

advertisement

Related manuals