USB Device. Sony MHC-V11


Add to my manuals
123 Pages

advertisement

USB Device. Sony MHC-V11 | Manualzz

18

GB

USB Device

Before using the USB device

For compatible USB devices, see

“Information about compatible devices” (page 33).

When using Apple devices with this system, connect them via a

BLUETOOTH connection (page 22).

Using Apple devices via a USB connection is not supported.

To use the system as a battery charger

You can use the system as a battery charger for USB devices that have a rechargeable function.

Connect the USB device to the

(USB) port.

The charging begins when the USB device is connected to the (USB) port. For details, refer to the operating instructions of your USB device.

Notes

• When USB cable connection is necessary, use the USB cable supplied with the USB device. See the operating instructions supplied with the USB device for details on the operation method.

• It may take a long time before “SEARCH” appears on the display depending on the type of USB device connected.

• Do not connect the system and the USB device through a USB hub.

• When the USB device is connected, the system reads all the files on the USB device. If there are many folders or files on the USB device, it may take a long time to finish reading the USB device.

• With some connected USB devices, there may be a delay before an operation is performed by this system.

• Compatibility with all encoding/writing software cannot be guaranteed. If audio files on the USB device were originally encoded with incompatible software, those files may produce noise or interrupted audio, or may not play at all.

• This system does not necessarily support all the functions provided in a connected

USB device.

• Do not remove the USB device during transfer or erase operations. Doing so may corrupt the data on the USB device or damage the USB device itself.

Transferring music from a disc

You can transfer music from a disc

(CD-DA disc or MP3 disc) to a USB device as follows:

CD SYNC transfer: Transfers all the

CD-DA tracks from the CD-DA disc.

MP3 folder transfer: Transfers MP3 files in a specific folder from the MP3 disc.

REC1 transfer: Transfers a currently playing track or MP3 file from the disc.

1

Press FUNCTION repeatedly until “CD” appears on the display.

2

Connect the USB device to the

(USB) port.

3

Load a disc you want to transfer.

4

Prepare for transfer.

Proceed to step 5 in case of CD

SYNC transfer.

For MP3 folder transfer

To transfer MP3 files in a specific folder, press +/– repeatedly to select the folder you want. Then start playback and press

 once.

Make sure the elapsed playing time has stopped on the display.

MHC-V11.4-582-493-72(1)

For REC1 transfer

Press

/ to select the track or MP3 file you want to transfer, then start playback.

To transfer an MP3 file in a specific folder, press +/– repeatedly to select the folder you want, then press

/ to select the MP3 file you want to transfer. Then start playback.

5

Press REC TO USB.

“READY” appears on the display.

6

Press .

The transfer starts, then “USB REC” appears on the display.

Do not remove the USB device until the transfer is complete.

When the transfer is complete,

“COMPLETE” appears on the display and audio files in MP3 format will be created.

To stop transfer

Press

.

REC1 transfer

Source

MP3

CD-DA

Folder name

File name

“MP3_REC1” Same as the source

“CD_REC1” “TRACK001”*

* Folder and file numbers are assigned serially thereafter.

Notes

• CD-TEXT information is not transferred in the created MP3 files. This system does not support the CD-TEXT standard.

• The transfer stops automatically if:

— the USB device runs out of space during transfer.

— the number of audio files and folders on the USB device reaches the limit for the number that the system can recognize.

• If a folder or file that you are trying to transfer already exists on the USB device with the same name, a sequential number is added after the name without overwriting the original folder or file.

• Do not use buttons on the remote control or unit during transfer to prevent transfer from stopping.

Note on copyright-protected content

The transferred music is limited to private use only. Use of the music beyond this limit requires permission of the copyright holders.

Folder and file generation rules

When transferring to a USB device, a “MUSIC” folder is created directly below “ROOT.” Folders and files are generated within this “MUSIC” folder according to the transfer method and source as follows:

CD SYNC transfer

Source

CD-DA

Folder name

File name

“CDDA001”* “TRACK001”*

MP3 folder transfer

Source

MP3

Folder name

File name

Same as the source

19

GB

MHC-V11.4-582-493-72(1)

20

GB

Playing a file

The following audio file formats are supported:

—MP3: file extension “.mp3”

—WMA: file extension “.wma”

1

Press FUNCTION repeatedly until “USB” appears on the display.

2

Connect the USB device to the

(USB) port.

3

Press

to start playback.

4

Press VOL +/– to adjust the volume.

Other operations

To

Pause playback

Stop playback

Select a folder

Press +/– repeatedly.

Select a file Press

/.

Find a point in a file

Hold down

/ during playback, and release the button at the desired point.

Select Repeat

Play

Do this

Press

. To resume play, press

.

Press

. To resume play, press

1)

. To cancel resume play, press

 twice.

Change the play mode

Press REPEAT/FM

MODE repeatedly until “REP ONE

“REP OFF 5)

2)

” appears on the display.

,” “REP

FLDR

3)

,” “REP ALL

4)

” or

Press PLAY MODE repeatedly while the

USB device is stopped.

You can select normal play (“FLDR” for all files in the folder on the USB device), shuffle play (“SHUF” or

“FLDRSHUF” for folder shuffle), or program play (“PROGRAM”).

1) When playing a VBR MP3/WMA file, the system may resume playback from a different point.

2) “REP ONE”: Repeats the current file.

3)

“REP FLDR”: Repeats the current folder.

4)

“REP ALL”: Repeats all files on a USB device.

5)

“REP OFF”: Turns off Repeat Play.

Notes

• This system cannot play audio files on the

USB device in the following cases;

— when the total number of audio files on a USB device exceeds 999.

— when the number of folders on a USB device exceeds 256 (including the

“ROOT” folder and empty folders).

These numbers may vary depending on the file and folder structure. Do not save other types of files or unnecessary folders on a USB device that has audio files.

• The system can play back to a depth of 8 folders only.

• Files and folders are displayed in the order of their creation on the USB device.

• Folders that have no audio files are skipped.

• Note that even when file name has the correct file extension, if the actual file differs, the system may produce noise or may malfunction.

To erase audio files or folders from the USB device

1

Press FUNCTION repeatedly until

“USB” appears on the display.

2

Connect the USB device to the

(USB) port.

3

Press

/ or +/– repeatedly to select the audio file or folder you want to erase, then start playback.

4

Press OPTIONS.

5

Press / repeatedly to select

“ERASE,” then press .

6

Press / to select “FOLDER” or

“FILE,” then press .

“ERASE??” flashes on the display.

7

Press .

When erasing is complete,

“COMPLETE” appears on the display.

MHC-V11.4-582-493-72(1)

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement

Table of contents