Fluid. Exmark LAZER Z LZX940KC726, LAZER Z LZX980KC606, LAZER Z LZX801KA606SS, LAZER Z LZX980KC726, LAZER Z LZX680KC486, LAZER Z X-SERIES Operators, LAZER Z LZX801KA606, LAZER Z LZX740KC606CA, LAZER Z LZX740KC526, LAZER Z LZX749EKC606

Add to my manuals
64 Pages

advertisement

Fluid. Exmark LAZER Z LZX940KC726, LAZER Z LZX980KC606, LAZER Z LZX801KA606SS, LAZER Z LZX980KC726, LAZER Z LZX680KC486, LAZER Z X-SERIES Operators, LAZER Z LZX801KA606, LAZER Z LZX740KC606CA, LAZER Z LZX740KC526, LAZER Z LZX749EKC606 | Manualzz

Maintenance

For Kohler EFI Units:

WARNING

Fuel system components are under high pressure. The use of improper components can result in system failure, gasoline leakage and possible explosion.

Use only approved fuel lines and fuel filters for high pressure systems.

Replacement Filters

Kohler

Kawasaki

Kohler EFI

Kohler P/N 24 050 13

Kawasaki

P/N 49019-7005

Kohler P/N 25 050 42

Note: It is important to reinstall the fuel line hoses and secure with plastic ties the same as they were originally installed at the factory to keep the fuel line away from components that could cause fuel line damage.

Change Hydraulic System

Filter and Fluid

Service Interval: Every 500 hours

Note: Only use Exmark Hydro Filter–Part No.

116-0164 for summer or winter.

1. Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2. Raise the rear of machine up and support with jack stands (or equivalent support) just high enough to allow drive wheels to turn freely.

CAUTION

Raising the mower deck for service or maintenance relying solely on mechanical or hydraulic jacks could be dangerous. The mechanical or hydraulic jacks may not be enough support or may malfunction allowing the unit to fall, which could cause injury.

Do Not rely solely on mechanical or hydraulic jacks for support. Use adequate jack stands or equivalent support.

3. Remove the pump drive belt.

4. Place a catch pan under the hydro.

5. Carefully clean area around the filters. It is important that no dirt or contamination enter the hydraulic system.

6. Using a socket, unscrew filters to remove and allow oil to drain.

7. Before installing the new filters, apply a thin coat of Exmark Premium Hydro oil on the surface of the two rubber seals.

8. Install the new filters and torque to 14 ft-lb (19

N-m).

9. Fill the hydraulic system as stated in Check

Hydraulic Oil Level section.

Exmark Premium Hydro Oil is recommended.

Refer to the chart for an acceptable alternative:

Hydro Oil

Exmark Premium Hydro

Oil (Preferred)

Mobil 1 15W50

Change Interval

500 Hours

250 Hours

10. Remove the catch pan and properly dispose of hydro oil and filter according to local codes.

11. Re-install the pump drive belt.

12. Start engine and move throttle control ahead to full throttle position. Move the speed control levers to the full speed and run for one minute.

Shut down the machine, allow the hydros to cool and recheck oil level.

13. Remove the jack stands.

Note: Do Not change the hydraulic system oil

(except for what can be drained when changing filter), unless it is felt the oil has been contaminated or been extremely hot.

Changing oil unnecessarily could damage hydraulic system by introducing contaminants into the system.

Wheel Hub - Slotted Nut

Torque Specification

Service Interval: After the first 100 hours

Every 500 hours thereafter

See Figure 26 to determine which slotted nut has

been installed on the unit.

38

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals