English. MSI MS-7877 v1.1, GP66 Leopard (Intel® 10th Gen) (GeForce 30 Series), J1900I


Add to my manuals
122 Pages

advertisement

English. MSI MS-7877 v1.1, GP66 Leopard (Intel® 10th Gen) (GeForce 30 Series), J1900I | Manualzz

English

Thank you for choosing the J900I Series (MS-7877 v.X) Mini-ITX motherboards.

The J900I Series motherboard is design based on Intel

®

Celeron J900 processor.

The J900I Series motherboards deliver a high performance and energy saving solution for BOX PC.

Layout

Top : mouse

Bottom: keyboard

Top: VGA Port

Bottom: DVI-D

JPWR2

CPUFAN

DIMM1

SYSFAN1

HDMI port

USB3.0 port

Top: LAN Jack

Bottom: USB 2.0 ports

T:

M:

Line-In

Line-Out

B: Mic

JAUD1

PCI_E1

JUSB1

JFP1 JCOM1

JTPM1

DIMM2

SATA1 SATA2

JPWR1

JBAT1 JCI1

Motherboard Specifications

CPU

Support

Memory

Support

■ Intel ® Celeron J900 processor

2x DDR3 SO-DIMM memory slots supporting up to 8GB

Supports DDR3 333/ 066 MHz

Dual channel memory architecture

■ x PCIe 2.0 x slot Expansion

Slots

Onboard

Graphics

Storage

USB

Audio

LAN

Back Panel

Connectors

■ x DVI-D port, supports the maximum resolution of 920x080

@ 60Hz, 24bpp x VGA port, supporting a maximum resolution of 2560x600

@ 60Hz, 24bpp

x HDMI port, supporting a maximum resolution of 920x200

@ 60Hz, 24bpp

■ 2x SATA 3Gb/s ports

■ x USB 3.0 port on the back panel

4x USB 2.0 ports (2 ports on the back panel, 2 ports available through an onboard USB 2.0 connector)

■ Realtek

®

ALC887 Codec

■ Realtek

®

RTL8G Gigabit LAN controller

■ x PS/2 keyboard port x PS/2 mouse port x VGA port x DVI-D port x HDMI port x USB 3.0 port x LAN (RJ45) port

2x USB 2.0 ports

3x audio jacks

2

Internal

Connectors

BIOS

Features

Form Factor

■ x 24-pin ATX main power connector x 4-pin ATX 2V power connector

2x SATA 3Gb/s connectors x USB 2.0 connector (supports additional 2 USB 2.0 ports) x 4-pin CPU fan connectors x 4-pin system fan connector x Front panel audio connector x Serial port connector x TPM connector x System panel connector x Chassis Intrusion connector x Clear CMOS jumper

■ x 64 Mb flash

UEFI AMI BIOS

Mini-ITX Form Factor

6.7 in. x 6.7 in. (7.0 cm x 7.0 cm)

For more information on compatible components, please visit http://www.msi.com/service/test-report/

3

Back Panel

PS/2 Mouse

VGA

PS/2 Keyboard

DVI-D

LAN

HDMI

USB 3.0

®

USB 2.0

Audio

LAN LED Indicator

LINK/ACT

LED

SPEED

LED

LED

Link/ Activity LED

Speed LED

LED Status

Off

Yellow

Blinking

Off

Green

Orange

Description

No link

Linked

Data activity

0 Mbps connection

00 Mbps connection

Gbps connection

Audio 2, 4, 6 or 8-channel configuration

Port

Blue

Green

Pink

Front audio

2-channel

Line in

Line out

-

Mic

4-channel

RS-Out

FS-Out

-

Mic

6-channel

RS-Out

FS-Out

-

CS-Out

8-channel

RS-Out

FS-Out

CS-Out

SS-Out

4

Memory Installation

The SO-DIMM slot is intended for memory modules.

.

Locate the SO-DIMM slot. Align the notch on the DIMM with the key on the slot and insert the DIMM into the slot.

2.

Push the DIMM gently downwards until the slot levers click and lock the DIMM in place.

2

Important

You can barely see the golden finger if the DIMM is properly inserted in the DIMM slot.

To uninstall the DIMM, flip the slot levers outwards and the DIMM will be released instantly.

5

Internal Connectors

JPWR~2: ATX Power Connectors

These connectors allow you to connect an ATX power supply. To connect the ATX power supply, align the power supply cable with the connector and firmly press the cable into the connector. If done correctly, the clip on the power cable should be hooked on the motherboard’s power connector.

Video Demonstration

Watch the video to learn how to install power supply connectors.

http://youtu.be/gkDYyR_83I4

1.+3

.3V

.3V

JPWR

9.5V

12.+

SB

12V

3.3V

13.+

16.P

3.3V

roun

19.G

d

20.R

roun

#

22.+ roun d

24.G

5V

5V roun d und und

JPWR2

4.+1

2V

2V

Important

Make sure that all the power cables are securely connected to a proper ATX power supply to ensure stable operation of the motherboard.

JCOM: Serial Port Connector

This connector is a 6550A high speed communication port that sends/receives 6 bytes FIFOs. You can attach a serial device.

6.DS

R

10.N

R

S o Pin

1.DC

D

UT

S

6

SATA~2: SATA Connectors

This connector is a high-speed SATA interface port. Each connector can connect to one SATA device. SATA devices include disk drives (HDD), solid state drives (SSD), and optical drives (CD/ DVD/ Blu-Ray).

Video Demonstration

Watch the video to learn how to Install SATA HDD.

http://youtu.be/RZsMpqxythc

Important

Many SATA devices also need a power cable from the power supply. Such devices include disk drives (HDD), solid state drives (SSD), and optical drives (CD / DVD /

Blu-Ray). Please refer to the device’s manual for further information.

Many computer cases also require that large SATA devices, such as HDDs, SSDs, and optical drives, be screwed down into the case. Refer to the manual that came with your computer case or your SATA device for further installation instructions.

Please do not fold the SATA cable at a 90-degree angle. Data loss may result during transmission otherwise.

SATA cables have identical plugs on either sides of the cable. However, it is recommended that the flat connector be connected to the motherboard for space saving purposes.

JCI: Chassis Intrusion Connector

This connector connects to the chassis intrusion switch cable. If the computer case is opened, the chassis intrusion mechanism will be activated. The system will record this intrusion and a warning message will flash on screen. To clear the warning, you must enter the BIOS utility and clear the record.

7

CPUFAN,SYSFAN: Fan Power Connectors

The fan power connectors support system cooling fans with +2V. If the motherboard has a System Hardware Monitor chipset on-board, you must use a specially designed fan with a speed sensor to take advantage of the CPU fan control. Remember to connect all system fans. Some system fans may not connect to the motherboard and will instead connect to the power supply directly. A system fan can be plugged into any available system fan connector.

4.Sp

1.Gro

nse und

Contr ol

CPUFAN

4.NC

1.Gro

Contr ol

SYSFAN

Important

Please refer to your processor’s official website or consult your vendor to find recommended CPU heatsink.

These connectors support Smart Fan Control with liner mode. The Command

Center utility can be installed to automatically control the fan speeds according to the CPU’s and system’s temperature.

If there are not enough ports on the motherboard to connect all system fans, adapters are available to connect a fan directly to a power supply.

Before first boot up, ensure that there are no cables impeding any fan blades.

JAUD: Front Panel Audio Connector

This connector allows you to connect the front audio panel located on your computer case. This connector is compliant with the Intel

®

Front Panel I/O Connectivity Design

Guide.

2.Gro

und

10.H

ead

Phon ction e De tectio n

5.He

L

9.He

R ad P ad P

_SEN

D

L

8

JFP: System Panel Connector

These connectors connect to the front panel switches and LEDs. The JFP connector is compliant with the Intel ® Front Panel I/O Connectivity Design Guide.

When installing the front panel connectors, please use the optional M-Connector to simplify installation. Plug all the wires from the computer case into the M-Connector and then plug the M-Connector into the motherboard.

Video Demonstration

Watch the video to learn how to Install front panel connectors.

http://youtu.be/DPELIdVNZUI

Pow

Pow er Sw er LE

D itch

2.+

10.N

4.-

6.+ o Pin

JFP

1.+

3.-

5.-

7.+

9.Re

HDD

Rese serve d

LED t Sw itch

Important

On the connectors coming from the case, pins marked by small triangles are positive wires. Please use the diagrams above and the writing on the optional M-Connectors to determine correct connector orientation and placement.

JUSB: USB 2.0 Expansion Connector

This connector is designed for connecting high-speed USB peripherals such as USB

HDDs, digital cameras, MP3 players, printers, modems, and many others.

6.US

C

10.N

B1-

B1+

C und

3.US

C

7.Gro

B0-

Pin

Important

Note that the VCC and GND pins must be connected correctly to avoid possible damage.

9

JTPM: TPM Module Connector

This connector connects to a TPM (Trusted Platform Module). Please refer to the

TPM security platform manual for more details and usages.

4.3.3

8.5V

V Po

12.G

Pow

Q roun er dby p ower d d

1.LP

5.LP

C C

9.LP

C a lock

C a set

C a ddre ss & ss & data p data p in0 in1 in3

JBAT: Clear CMOS Jumper

There is CMOS RAM onboard that is external powered from a battery located on the motherboard to save system configuration data. With the CMOS RAM, the system can automatically boot into the operating system (OS) every time it is turned on. If you want to clear the system configuration, set the jumpers to clear the CMOS RAM.

Keep Data Clear Data

Important

You can clear the CMOS RAM by shorting this jumper while the system is off.

Afterwards, open the jumper . Do not clear the CMOS RAM while the system is on because it will damage the motherboard.

20

PCI_E: PCIe Expansion Slots

The PCIe slot supports the PCIe interface expansion card.

PCIe x Slot

Important

When adding or removing expansion cards, always turn off the power supply and unplug the power supply power cable from the power outlet. Read the expansion card’s documentation to check for any necessary additional hardware or software changes.

2

BIOS Setup

The default settings offer the optimal performance for system stability in normal conditions. You may need to run the Setup program when:

An error message appears on the screen during the system booting up, and requests you to run SETUP.

You want to change the default settings for customized features.

Important

Please load the default settings to restore the optimal system performance and stability if the system becomes unstable after changing BIOS settings. Select the

"Restore Defaults" and press <Enter> in BIOS to load the default settings.

If you are unfamiliar with the BIOS settings, we recommend that you keep the default settings to avoid possible system damage or failure booting due to inappropriate BIOS configuration.

Entering BIOS Setup

Power on the computer and the system will start the Power On Self Test (POST) process. When the message below appears on the screen, please <DEL> key to enter BIOS:

Press DEL key to enter Setup Menu, F to enter Boot Menu

If the message disappears before you respond and you still need to enter BIOS, restart the system by turning the computer OFF then back ON or pressing the

RESET button. You may also restart the system by simultaneously pressing <Ctrl>,

<Alt>, and <Delete> keys.

MSI additionally provides a method to enter the BIOS setup. You can click the

“GO2BIOS” tab on “MSI Fast Boot” utility screen to enable the system going to BIOS setup directly at next boot.

Click "GO2BIOS" tab on "MSI Fast

Boot" utility screen.

Important

Please be sure to install the “MSI Fast Boot” utility before using it to enter the BIOS setup.

22

Overview

After entering BIOS, the following screen is displayed.

BIOS menu selection General Help information

Menu display

▶ BIOS menu selection

Main - Use this menu for basic system configurations, such as time, date etc.

Advanced - Use this menu to set up the items of special enhanced features.

M-Flash - This menu provides the way to update BIOS with a USB flash disk.

Boot - Use this menu to specify the priority of boot devices.

Security - Use this menu to set supervisor and user passwords.

Save & Exit - This menu allows you to load the BIOS default values or factory default settings into the BIOS and exit the BIOS setup utility with or without changes.

▶ Menu display

This area provides BIOS settings and information to be configured.

▶ General Help information

The General Help displays a brief description to assist you in understanding the selected item.

23

24

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Key Features

  • Intel NA (integrated CPU) J1900
  • PC mini ITX Realtek ALC887
  • DDR3-SDRAM 2 SO-DIMM Maximum internal memory: 8 GB
  • SATA
  • 2048
  • Clear CMOS jumper

Related manuals