AMS AS5600
Manuals and User Guides for AMS AS5600. We found 8 manuals for free downloads User Guide, Data Sheet
AMS AS5600 is an angle and position sensor, which combines the latest advancements of ams’ magnetic sensor technology with excellent positioning performance. The AS5600 supports an automotive temperature range of -40°C to 150°C and, as such, can be used in harsh environments, making it a perfect fit for automotive and industrial applications. With its magnetic immunity, mechanical robustness, and overall cost-effectiveness, AS5600 is suited for use in many demanding applications, including: * Steering angle sensing and position detection * Rotary position feedback in motor control * Throttle position sensing * Angular position and speed measurement * Absolute rotary position encoding * Non-contact position feedback in power tools and home appliances
Key Features
Automotive temperature range (-40°C to 150°C)
Magnetic immunity
Mechanical robustness
Cost-effectiveness
Suitable for demanding applications
Pages: 12 AMS AS5600 User Guide
Brand: AMS Category: Measuring, testing & control Size: 613 KB
Languages: English
Table of contents
Open manualOther manuals and documents
Frequently Answers and Questions
What is the temperature range of AMS AS5600?
The temperature range of AMS AS5600 is -40°C to 150°C.
Is AMS AS5600 magnetically immune?
Yes, AMS AS5600 is magnetically immune.
Is AMS AS5600 suitable for automotive applications?
Yes, AMS AS5600 is suitable for automotive applications.
Questions & Answers
Z Z D
How to set the zero position on the device?
The zero position can be set via the Demo GUI Config page, where you can configure the current zero and maximum positions.
Z Z D
How to set the zero position?
Setting the zero position can be done through the Demo GUI Config page, where the current zero and maximum positions can be set.
A A A
How to interpret the AGC range to determine if the magnet is too far or too close, and how to address any deviations?
To determine if an AGC range is too far or too close, you need to know the operating voltage. For robust performance, the gain value (AGC) should be in the center of its range and deviations should be minimal.
- For 5V Operation: The ideal center would be around 127. An AGC range lower than 127 would suggest the magnet might be a bit too far. However, this deviation may be acceptable depending on your application's requirements.
- For 3.3V Operation: The ideal center would be around 64. An AGC range significantly higher than 64 means that the IC is running at 5V configuration.
It is recommended to adjust the air gap (distance between the magnet and the AS5600) to bring the AGC value closer to the center of the appropriate range for optimal performance.
How to correct inaccurate angle readings on an AS5600 that reaches the maximum value (4095) before completing a half turn?
The angular range of the AS5600 likely isn't configured correctly. Program the AS5600 to define the start and stop positions (zero angle and maximum angle) that correspond to the application's actual range of motion. Refer to the ZPOS/MPOS/MANG register descriptions and the angle programming section for configuration steps. Ensure the angular range is greater than 18 degrees. Configuring a smaller range improves accuracy. Verify magnet detection (MD = 1) for successful writing.
How should the STATUS register byte be interpreted to understand MH, ML, and MD statuses?
The STATUS register byte needs to be interpreted by looking at the individual bits:
- MD (Magnet Detected): If the MD bit is 1, the magnet is detected; if 0, the magnet is not detected.
- ML (AGC Maximum Gain Overflow): If the ML bit is 1, the magnet may be too weak.
- MH (AGC Minimum Gain Overflow): If the MH bit is 1, the magnet may be too strong.
For example, if the byte value is 103 (0x67 in hexadecimal, 01100111 in binary), then MH = 0, ML = 1, and MD = 1, indicating that the magnet is detected but may be too weak.
advertisement