Harmar Mobility Pinnacle SL600
Manuals and User Guides for Harmar Mobility Pinnacle SL600. We found 3 manuals for free downloads Owner's manual, Installation And Service Manual
Harmar Mobility Pinnacle SL600 is a compact stair lift featuring a patented drive system, wireless remotes, user-friendly controls, and safety features like obstruction sensors, a retractable seat belt, and an interlock on the swivel seat. With a weight capacity of 350 lbs and a speed of 20 feet per minute, it can be used on stairs with angles between 32 and 52 degrees. It runs on a 24 VDC battery and has a manual override operation for emergencies. The folding rail model automatically deploys and retracts as the lift ascends or descends, ensuring safety and convenience.
Key Features
Step-by-step installation procedures for rail and chassis
Remote call/send control operation with reprogramming instructions
Adjustable upper and lower travel limits for customized fit
Comprehensive safety stop switches for obstruction detection
Optional folding rail installation and conversion procedures
LED indicator light for system status and safety alerts
Adjustable seat height for user comfort
Battery charger for continuous operation
Pages: 12 Harmar Mobility Pinnacle SL600 Owner's manual
Brand: Harmar Mobility Category: Stairlifts Size: 5 MB
Languages: English
Table of contents
Open manualOther manuals and documents
Frequently Answers and Questions
What tools are required for the installation of the stair lift?
A cordless drill, Allen wrenches (5/64”, 5/32”, 3/16”, 5/16”), Phillips screwdriver (#3), Nut driver (3/8” and 5/16”), 6-10” driver extension, T30 Torx bit (included), level, hacksaw or chop saw, SAE socket set, SAE wrenches, and tape measure are suggested.
How is the overall rail length determined for a standard stairway?
Measure the overall length of the stairs from the nose at the top landing to the floor at the bottom, then add 13” to this measurement. This ensures enough rail length for proper seat height adjustment at both ends.
What does a yellow LED indicator light on the armrest control signify?
A yellow LED indicator light means that one of the system controls or safety sensors is currently engaged.
How can the remote call/send controls be reprogrammed?
Start with the red 'ON/OFF' switch in the 'OFF' position, disconnect the 6-pin footrest and 8-pin chair wire harnesses, press and hold the install switch, turn the 'ON/OFF' switch to 'ON', release the install switch, then press 'UP' or 'DOWN' on each remote control.
What is the minimum clearance required between the underside of the rail and the stair tread nose?
The underside of the rail must be at least 2 inches above the stair tread nose to provide adequate clearance for the footrest.
Questions & Answers
X X A
What to do if the chair lift remote control is unresponsive?
If the chair lift fails to respond to the remote control, the batteries may be discharged and need replacement. Remove the back cover of the control and replace the batteries with commonly available AAA batteries, ensuring correct polarity.
X X A
What to do if the chair lift remote control is not working?
If the chair lift fails to respond to the remote control, the batteries may be discharged and need replacement. Remove the back cover of the control and replace the batteries with commonly available AAA batteries, ensuring correct polarity.
O O B
What to do if the stair lift doesn't respond to the remote control after replacing the batteries?
The remote call/send controls may need to be re-programmed. Remember to program both controls in one programming cycle. If the problem continues, further troubleshooting may be needed.
O O B
What should be done if the stair lift does not respond to the remote control, even after replacing the batteries?
The remote call/send controls may need to be re-programmed. The manual provides a detailed, step-by-step guide of how to re-program the remote call/send controls. It is essential to program BOTH controls in one programming cycle. If issues persist, further troubleshooting steps or professional assistance may be required.
X X A
What to do if the remote control of a chair lift is not working?
If the chair lift isn't responding to the remote control, the batteries might be low. Try replacing them with new AAA batteries, making sure to put them in with the correct polarity.
O O B
What to do if the stair lift doesn't respond to the remote control after replacing the batteries?
The remote call/send controls may need to be re-programmed. The manual provides a detailed, step-by-step guide of how to re-program the remote call/send controls. It is essential to program BOTH controls in one programming cycle. If issues persist, further troubleshooting steps or professional assistance may be required.
X X A
What to do if the remote control is not working?
If the chair lift fails to respond to the remote control, the manual indicates that the batteries may be discharged and need replacement. Remove the back cover of the control and replace the batteries with commonly available AAA batteries, ensuring correct polarity.
advertisement