Zojirushi CD-WCC40 Combination Water Boilers & Warmer Operating instructions

Sf ZÖNRUSH
MICOM WATER BOILER & WARMER OPERATING INSTRUCTIONS
CD-WCC30 / CD-WCC40
I
IMPORTANT SAFEGUARDS .....................m..eeeeenennnnee es 2
SPECIFICATIONS -................eeeeeeeeeenennenenneenenee anne nene. 5
PARTS NAMES AND FUNCTIONS mm... 6
BOIL MODE -...................meeeeeennnrenneenenenenneneneneeeenennenee—.. 8
DISPENSE HOT WATER -...................eeeeeeeeeeeen nee 10
DISPOSE WATER ..................e-m..0e0meecinneerenennea reee nne eee 10
REBOIL MODE -.................eeeemeeenneeneenenennenenene ene nenneneee. 11
AUTOMATIC SHUT-OFF FUNCTIÓN -..................————— 11
HOW TO SET THE KEEP WARM MODE ..................——.—..- 12
QUICK TEMP MODE -...............e.eemeeeeeeeneneenennennee eee. 14
ENERGY-SAVING TIMER FUNCTIÓN -...................—————... 14
CAFÉ DRIP DISPENSING MODE 15
HOW TO CHANGE THE INFORMATION SOUND ............ 15
CLEANING AND MAINTENANCE ..............e—... eme ..eeeee——.. 16
®HOW TO REPLACE THE INNER LID GASKET .......... 16
HOW TO PERFORM CITRIC ACID CLEANING ............... 17
REPLACEMENT PARTS -.................e.eeeeneineneneenenenneneee. 17
Q8A ON PRODUCT USE essen EEE 18
TROUBLESHOOTING GUIDE -................--. mmm. 18
ZOJIRUSHI CORPORATION
IMPORTANT SAFEGUARDS
BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED WHEN
USING ELECTRICAL APPLIANCES, INCLUDING THE FOLLOWING:
1.
2.
8
9.
10.
11.
12.
13.
14.
15.
Read all instructions thoroughly.
Avoid touching hot surfaces and do not close or clog the steam vent opening under
any circumstances. The handles and knobs are provided for your safety and
protection.
. To safeguard against fire, electric shock and possible injury, keep the power cord,
plugs and the appliance away from water or other liquids.
. Close supervision is recommended when any appliance is used by or near
children.
. Unplug from outlet when not in use and before cleaning. Allow the appliance to
cool before adding or removing parts, and before cleaning the appliance.
. Do not use or operate any appliance with a damaged cord or plug. If the appliance
malfunctions or has been damaged in any manner, unplug the appliance and return
it to the nearest authorized service facility or dealer for examination, repair or
adjustment.
. The use of accessories or attachments not recommended by the appliance
manufacturer may result in fire, electric shock or other injury to persons.
. Do not use outdoors.
Keep the power cord away from hot surfaces and do not let the cord hang over the
edge of tables or counters.
Do not place on or near a heated surface such as a gas or electric stove, or in a
heated oven.
Always use extreme caution when moving an appliance containing hot liquids.
The plug to the appliance should be attached first before plugging the cord into a
wall outlet.
Do not use the appliance for other than intended or specified purposes.
To protect against electrical hazard, unplug the cord before cleaning.
Scalding may occur if the lid is removed during boiling cycles.
NOTE: This appliance has a polarized plug (one blade is wider than the other). To
reduce the risk of electric shock, this plug was designed to fit into a polarized
outlet in only one direction. If the plug does not fit fully into the outlet, do not
attempt to force it or modify it in any way. Simply reverse the plug and insert. If
it still does not fit, contact a qualified electrician.
SAVE THESE INSTRUCTIONS
THIS APPLIANCE IS FOR HOUSEHOLD USE ONLY.
A.
B.
C.
A short detachable power-supply cord has been provided for your safety. To
reduce risks from entanglement or tripping, a longer cord is not recommended.
Extension cords should only be used if care is exercised.
If using an extension cord: (1) the marked electrical rating of the detachable
power-supply cord or extension cord should be at least as high as the electrical
rating of the appliance; (2) if the appliance is of the grounded type, the extension
cord should have a ground-type 3-pronged plug; and (3) the longer cord should not
drape over the countertop or tabletop where it can be pulled on by children or
tripped over.
IMPORTANT SAFEGUARDS
Before use
These WARNINGS and CAUTIONS are intended to protect you and others from personal injury and
household damage. To ensure safe operation, please follow carefully.
Do not modify the product. Only a repair technician
may disassemble or repair this unit.
* Attempting to do so may cause fire, electric shock or
injury. Make any repair inquiries to Zojirushi Customer
Service.
Do not immerse the product in water or splash it
with water, and do not put it on a wet surface such
as a sink.
* Doing so may cause short circuit or electric shock.
Do not allow liquid to come into contact with the
Receptacle or Power Cord.
* Doing so may cause short circuit or electric shock.
Do not plug or unplug the Power Cord if your
hands are wet.
* Doing so may cause electric shock or injury.
Do not touch the Steam Vent or bring your hands
or face near the Steam Vent.
* Doing so may cause burns or scalding. Take special
precautions with children and infants.
Do not cover the Steam Vent with anything such
as a dishcloth.
* Hot water may spill out, resulting in scalds. It may also
cause deformation or discoloration of the Upper Lid or
breakdown of the product.
Do not allow children to use the product
unsupervised. Keep it out of the reach of infants.
* Children are at risk of burns, electric shock or injury.
Do not fill over the Maximum Water Level Line.
* Overfilling may cause hot water to spill out, resulting in
scalds.
Always remove the Upper Lid before disposing
hot water.
* The Upper Lid may fall off and cause hot water to splash,
resulting in scalds.
Do not tilt or shake the product or carry in your
arms. Do not move it or drain hot water by holding
the Upper Lid.
* Doing so may result in scalding by hot water spilling out
from the Spout or Steam Vent, even if the Automatic
Dispense Lock is on. Always use the handle when
carrying.
Do not tilt the product or tip it over.
* Hot water may spill from the Spout or Steam Vent,
even if the Automatic Dispense Lock is on.
Do not slam the Upper Lid when closing.
* Hot water may dispense or spill out, resulting in scalds.
Do not use the product if the Power Plug or Power
Cord is damaged or if the Power Plug is loosely
inserted into the electrical outlet.
* Doing so may cause electric shock, short circuit or fire.
Close the Upper Lid securely.
* Hot water may spill out when the product is overturned,
resulting in scalds.
Do not remove the Upper Lid while boiling.
Do not damage the Power Cord. Do not bend, pull,
twist, fold, or attempt to modify the Power Cord.
Do not place it on or near high temperature
surfaces or appliances, under heavy items or
between objects.
* A damaged Power Cord can cause fire or electric
shock.
Do not use the product as a cooler or place ice
inside of it.
* Doing so may cause condensation, resulting in electric
shock or breakdown of the product.
Do not allow the end of the Appliance Plug to
become soiled with dust or come into contact with
any metal objects.
* Doing so may cause electric shock, short circuit or fire.
Do not allow infants or children to put the
Appliance Plug in their mouth.
* Doing so may cause electric shock or injury. Take
special precautions with children and infants.
Insert the Power Plug completely and securely
into the electrical outlet.
* A loosely inserted Power Plug may cause electric
shock, short circuit, smoke or fire.
Use only an electrical outlet rated at 15 amperes
minimum, and do not plug other devices into the
same outlet.
* Plugging other devices into the same outlet may cause
the electrical outlet to overheat, resulting in fire.
If the blades or surface of the Power Plug become
soiled, wipe them clean.
* A dirty Power Plug may cause fire.
Do not use a power source other than 120 V AC.
* Use of any other power supply voltage may cause fire
or electric shock.
Do not boil anything other than water.
* Attempting to boil, cook, or heat up the following items
may cause bubbling or boiling over, which may cause
scalding. Doing so may also cause clogging of the
water route or Electric Pump, corrosion of the Inner
Container, or peeling of the Nonstick Coating.
- Milk, sake, soup, charcoal, tea bags or tea leaves.
* Instant food.
* Food and sauce pouches or foods in plastic bags.
Replace the Inner Lid Gasket if it hardens, changes
Shape, turns white, or otherwise becomes worn out.
* Hot water may spill out when the productis tilted or
tipped over accidentally, and may cause scalding.
OThe illustrations used in these Operating Instructions may vary from the actual product you have purchased.
IMPORTANT SAFEGUARDS (cont)
This product is not intended for
use by persons (including
children) with reduced physical,
sensory or mental capabilities, or
lack of experience and
knowledge, unless they have
been given supervision or
instruction concerning use of the
product by a person responsible
for their safety. Children should
be supervised to ensure that they
do not play with the product.
Stop using immediately if you notice any of the following symptoms
indicating a malfunction or breakdown.
* Continued use of the product may cause smoke, fire, electric shocks or injury.
* The Power Plug or Power Cord has become very hot.
* The Power Cord is damaged or the electricity turns on and off when touched.
- The Body is deformed or unusually hot.
+ Smoke is arising from the product or there is a burning smell.
+ Some parts of the product is cracked, loose or unstable.
- The product emits steam for at least 10 minutes continuously and does not
turn to Keep Warm mode.
* Water leaks from the Body.
If any of the above occurs, unplug the product immediately and return to
Zojirushi Customer Service for check-ups and/or repairs.
CAUTIONS
Always use caution when opening the Upper Lid
and avoid skin contact with steam.
* Loose water or steam may escape upon opening the
Upper Lid and cause scalds.
Do not touch hot surfaces during or for a short
period of time after use.
Touching hot surfaces may cause burns. Be especially
careful with metal parts such as the Inner Lid and the
Inner Container.
Please allow the product to cool down before
cleaning.
* Touching hot surfaces may cause burns.
Do not use the product near walls or furniture.
Steam or heat may damage, discolor or deform walls or
furniture.
Do not swivel or move the product while
dispensing water.
* Hot water may splash out, resulting in scalds.
Do not place or use the product on unstable
surfaces or on surfaces that are vulnerable to heat.
* Doing so may cause fire.
Do not attempt to dispense hot water while it is boiling.
* Hot water can spurt out, resulting in scalds.
Do not use other Power Cords than the one provided.
Do not use the Power Cord for other appliances.
Do not use the Power Cord for overseas models.
* Doing so may cause malfunction or fire.
Do not place the product over direct flame (such
as a gas stove top), or on top of electric or
induction heating (IH) cookers.
* Doing so may cause fire, breakdown or damage of the
product.
Unplug the Power Plug from the outlet when the
product is not in use.
* Leaving the Power Plug in an outlet may cause the
insulation to become damaged, resulting in electric
shock, short circuit or fire, or result in injuries or scalds.
Do not touch the Lid Lock when carrying the product.
* Doing so may cause the Upper Lid to open, resulting in
injuries or scalds.
Always unplug the product by holding the Power
Plug, not by pulling the Power Cord.
* Pulling the Power Cord to unplug the product may
cause electric shock, short circuit or fire.
If the Power Cord is damaged, it must be replaced
by an appropriate cord or assembly made
available by the manufacturer or its service agent.
IMPORTANT
Do not operate the product when it is empty.
* Doing so may burn or damage the product.
Avoid rough handling, dropping or bumping the
product.
* Doing so may cause damage or cease operation of the
product.
Avoid letting steam make contact with cabinets and
Walls when using near or under a kitchen shelf.
* Doing so may cause discoloration or deformation.
Allow the product to dry completely when storing
the product in an area where it may freeze for a
long period of time.
* |f water left inside freeze, it may cause breakdown or
malfunction.
Avoid using the product near a radio, TV, computer, etc.
* The product may cause interference with certain electronics.
Do not drag the product over any surface while
attempting to move.
* Doing so may cause damage to surfaces such as
countertops.
Do not allow hot water to come into contact with
the Control Panel or the Water Level Gauge.
* Doing so may cause breakdown of the product.
Do not use the product where its steam may come
into contact with other electrical appliances.
* The steam may cause fire, malfunction, discoloration or
deformation to other electrical appliances.
This appliance is intended to be used in
household and similar applications such as;
* Staff kitchen areas in shops, offices and other working environments;
* Environments comparable to residential living rooms and kitchens;
* This appliance is not intended for use by many unspecified
people for a long period of time.
SPECIFICATIONS
Model No.
Capacity
CD-WCC30
101 oz. (3.0 liters)
CD-WCC40
135 oz. (4.0 liters)
Rating AC 120 V 60 Hz
Electric Consumption 700 W
Average Power 208°F (98°C) Approx. 41 W Approx. 48 W
Consumption | 195°F (90°C) Approx. 34 W Approx. 40 W
during Keep | 175°F (80°C) Approx. 28 W Approx. 31 W
160°F (70°C) Approx. 23 W Approx. 26 W
Length of the Power Cord 2'11" (0.9 m)
External (approx. inches) 8-14 (W) x 11-14 (D) x 11-15 (H) [ 8-14 (W) x 11-14 (D) x 13-15 (H)
Dimensions | (approx.cm) | 21 (W) x 28.5 (D) x 29 (H) 21 (W) x 28.5 (D) x 34 (H)
\ Weight (including the Power Cord) Approx. 5 Ibs. (2.3 kg) Approx. 6 Ibs. (2.4 kg) J
Oe The average Keep Warm electric power consumption is for one hour, provided that the Inner
Container is full and the room temperature is approximately 73°F (23°C).
Oe The height refers to the product when the handle is down.
@In high altitudes or severely cold areas, the product may not perform as specified. Avoid using the
product in such areas or in other extreme conditions.
e This product is not suitable for use in countries or regions with different power supply voltages or
frequencies.
PARTS NAMES AND FUNCTIONS
The light sound you may Lid Lock
Steam Vent
eExercise care during the
boiling process as steam
emitting from the Steam
Vent is very hot.
hear when opening and
closing the Upper Lid is
normal. (see pg. 19)
E
<<
=
Upper Lid
Inner Lid Gasket
Inner Lid \ (Consumable Part)
®|f the Inner Lid Gasket hardens,
changes shape, turns white, or
otherwise becomes worn out, please
Water Removal Area replace it with a new one. (Separate
charge required.) (see pg.16)
®Drain water here. Not doing so may allow the product
Я to leak hot water when tilted or
Inner Container tipped over resulting in scalding.
(Nonstick Coating)
Hinge
Maximum Water Level Line |
Control Panel o
. Handle
Spout S
eHot water dispenses from here. q
Water Level Gauge
REFILL Line
®Fill water above the line.
N. Receptacle
e Appliance Plug
inserts here.
Filter | Swivel Base
eFor care and use instructions, eDo not let the Power Cord
see pg. 16. wrap around the Main Body
when turning.
Power Cord AT:
E Twist Tie
ePlease remove the twist tie holding the Power Cord before use.
> eDo not use the Power Cord bundled up. Doing so may cause the
UN , Power Cord to become excessively hot, resulting in malfunction.
Power Plug
Appliance
Plug Cord
PARTS NAMES AND FUNCTIONS
CON TR OL PANEL eo Press buttons down firmly.
QUICK TEMP light
BOIL light
REBOIL/QUICK TEMP
button
DISPENSE button
Press to dispense hot water. (see pg.10, 15)
The raised dot ( e) in the center of the DISPENSE
button is provided for those with visual impairment.
CAFÉ DRIP light
Starts the Reboll - EE i
mode. (see pg.11) — — UNLOCK light
Sets the Quick 8 d
Temp mode.
(see pg.14)
Also used when
performing the Citric
Acid Cleaning (to
initiate cleaning, press
this button for more TEMP SET UNLOCK
than 3 seconds). button
(see pg.17) À This button must be
pressed to dispense hot
TEMP SET button water. (see pg.10) —
Sets the Keep Warm temperature. > ress 16 Dre Diode g
(see pg.12) mode. (see pg.15)
: Use this button when
KEEP WARM light changing the Information
. Sound. (see pg.15)
Display
LCD display shows the water temperature and Timer settings. ENERGY-SAVING
show all functions simultaneously during use.
NOTE: lllustration is for reference only. Actual display will not
Use when setting the Energy-Saving
Timer function. (see pg.14)
How to Open/Close the Upper Lid
To Open @ Press the indented area of the
Lid Lock with your thumb.
@ Pull the Lid Lock up with your
fingers to open the Upper Lid.
To Close Depress the Upper Lid until it
clicks shut.
Indented Area of
the Lid Lock
Lid Lock
How to Detach/Attach the Upper Lid
To Detach @ Open the Upper Lid to about
a 45-degree angle.
@ Push the Upper Lid Detach
button.
© Pull the Upper Lid forward
and up at an angle.
To Attach Push the Upper Lid back into
place at the same angle.
degrees
Upper Lid
Detach button
BOIL MODE
1 Open the Upper Lid and fill the
Inner Container with water using
a pitcher or other container.
To monitor the amount of Level Line
water you are filling, look at —
the thickness of the stripes on (MAX
Maximum Water
the Water Level Gauge.
Fr When the Inner
Container is empty.
Water
— Level ——
Gauge
The stripes on the
Water Level Gauge
appear thicker when
water is added.
Level
Present Water DS
eDo not fill the Inner
Container directly
from a water faucet
or place the product
on a wet surface
such as a sink.
(Exposing the
heating element
directly to water
may cause
malfunction.)
OAvoid splashing
water on the Body or
Control Panel. (May
cause malfunction.)
Close the Upper Lid
securely.
To ensure safe
operation while
boiling and to prevent
scalds if the product
is overturned.
[J
Be sure to insert the
Power Cord securely.
shock, may cause electric |
eDo not allow the
end of the
Appliance Plug to
get soiled with dust
or come into contact
with metal objects
such as pins.
shock, short circuit, smoke or
fire.
It automatically starts the boiling
process.
The BOIL light turns on and the Display
shows the water temperature.
Below 170*F: Display shows the water
temperature in 10°F increments.
Above 175°F: Display shows [175]- [180]
> [185] > 1190] > [195] > [200] > [205] > [212].
ест)
(EIN Ta CET
QUICK TEMP / TEMP
eHow to set the Quick
Temp mode: see pg. 14
E Temperature
Conversion Guide
The first time
zz | Fahrenheit (°F) | Celsius (°C)
212 100
208 98
195 90
175 80
160 70
73 23
eDo not fill over the Maximum Water
Level Line. (Hot water may overflow
from the Steam Vent.)
eDo not fill the Inner Container with hot
water. (The Automatic Shut-Off function
may be activated.) (see pg.11)
eDo not fill the Inner Container with any
liquid other than water.
eDo not use water additives such as
charcoal for water purification or
mineral additives. (Small particles may
get clogged inside of the product.)
@if you wish to shorten the time, add
less water to the Inner Container.
you use the product you
may notice the smell of
plastic. This is normal
and will gradually fade
@At your initial use or when
using the product after a long period of storage:
Attach the Filter, fill the Inner Container with water to
the MAX line and boil as directed. Once it reaches a
boil, dispense about 34 oz. (1 liter) of water to rinse
the water route and dispose the remaining water. Fill
with fresh water.
e When using mineral or Alkalized lonic water:
When mineral or Alkalized lonic water is used, a
floating residue may develop or a milky white
substance may form on the surface of the Inner
Container. This is due to the ingredients in the water
and is harmless to your health. Frequent cleaning is
recommended.
When boiling has completed, a melody
sounds and it automatically switches
to 195°F Keep Warm mode.
How to change the Information Sound
from a melody to a beep. (see pg.15)
The BOIL light turns off, the Keep Warm light
turns on and "212" appears on the Display.
Turns off
When the water
temperature drops to about
195°F, "195" appears on
the Display.
208°F Keep Warm Mode. (see pg.12)
175°F Keep Warm Mode. (see pg.12)
160°F Keep Warm Mode. (see pg.13)
ad
@Add water when the water level is
low during the Keep Warm mode.
(The product automatically begins
heating the water.) If the water level
is still not high enough, it will not
automatically switch to Boll. In this
Time required to boil water:
CD-WCC30
Approx. 31 minutes”
Length of time until the water
temperature reaches about 195°F:
CD-WCC30| Approx. 25 minutes
CD-WCC40
Approx. 39 minutes”
CD-WCC40 | Approx. 25 minutes
(At a room temperature of 73°F with the
Inner Container filled to the Maximum
Water Level Line with water temperature
at 73°F.)
% Includes approx. 4 minutes to
Dechlorinate.
(At a room temperature of 73°F with the
Inner Container filled to the Maximum
Water Level Line.)
@ The length of time for the water
temperature to reach 195°F will vary
depending on the amount of water and
room temperature.
case, press the REBOIL/QUICK
TEMP button to manually start the
process. (see pg.11)
@Please follow the instructions below
to reduce the risk of scalding:
- Do not cover the Steam Vent with a
cloth.
- Do not touch the Steam Vent or
bring your hands or face near the
Steam Vent.
- Do not open the Upper Lid while
the BOIL light is on.
- Do not dispense hot water while it
is boiling.
10
DISPENSE HOT WATER
2 Press the has) button to dispense hot water,
os
SLOW
The UNLOCK light turns on
and hot water can be
dispensed. Do not swivel the product while dispensing water.
®Initially upon boiling or if it has been a while after dispensing, the
water may not be very hot. Please discard the first cup (of the hot
water).
D @Do not attempt to dispense hot water while boiling.
@Do not unlock and press the ®Water may not dispense smoothly for a short period of time after
DISPENSE button if the Inner boiling.
Container is empty. ®Be careful as the Body heats up during the Boil and Keep Warm
modes.
D | S P OS E WAT E R Dispose the water when the product is not in use.
1 Unplug the Power Cord Hold the product with both hands and dispose water where indicated
and detach the Upper Lid. "EMPTY FROM HERE” on the wall of the Inner Container,
Hold the Handle
securely.
When disposing hot water: |
eTake precaution with the
hot water and steam.
You may scald yourself.
eTake precaution as hot
water may drip from the
( Spout, causing scalds. J
( When detaching the Upper Lid: |
®Take precaution with the steam.
You may scald yourself.
DISPENSE HOT WATER
Turns off He)
O
SLOW
10 seconds after dispensing,
the UNLOCK light turns off
and the Automatic Dispense
Lock is activated.
Automatic Dispense Lock
A safety function to prevent hot water
from dispensing if the DISPENSE
button is accidentally pressed.
®Even if no water is dispensed, the
Automatic Dispense Lock will be
activated after about 10 seconds.
f Do not tilt or shake the
product after dispensing.
Hot water may drip from the
This function is used when reboiling
water in the Keep Warm mode.
~ Reboil mode ~
REBOIL The BOIL light turns on when
Press the QUICK TEMP button. the boiling process begins.
Short beep
Time required to
finish reboiling
(At a room temperature of
73°F / 23°C with the Inner
Container filled to the
Maximum Water Level Line.)
208°F Keep Warm
160 Mode
Approx. 3—4 minutes
195°F Keep Warm
. . Mode
When the Reboil process is completed, )
the product switches to Keep Warm Approx. 5-8 minutes
mode.
ePressing the REBOIL/QUICK TEMP button twice activates
the Quick Temp mode. (see pg. 14)
eDo not attempt to dispense hot water while reboiling.
eWater may not dispense smoothly for a short period of time
after reboiling.
CD @Make sure the water level is above the REFILL Line
before pressing the REBOIL/QUICK TEMP button.
| Spout, causing scalds.
ad
eDo not plug or unplug the
Power Plug or Appliance
Plug with wet hands. (Doing
so may cause short circuit
or electric shock.)
eDo not dispose hot water
with the Upper Lid in place.
(The Upper Lid may come
off, spilling hot water and
causing scalds.)
eDo not allow water to splash
on the Control Panel, Hinge,
Handle or Receptacle.
(Could cause scalding or
breakdown.)
ePlease do not lose the Filter
while disposing water.
eDispose the water at least
once a day. (Leaving water
in the Inner Container can
cause unwanted odor or
scale build-up.)
No
~ Automatic Shut-Off function —
10 Short
beeps
eBe careful not to
repeat the boiling
process without
filling the Inner
Container with
INR water, as the
sound, the i i
lights will turn Nonstick Coating
on and "HH" will may discolor and
appear on the peel.
Display.
The Automatic Shut-Off function activates to shut down power to the
heater in order to prevent damage from overheating. The Display will
show "HH" and beeps will sound to alert you that the Automatic Shut-Off
has been activated. The following conditions may cause activation:
eWhen plugged in without filling the Inner Container with water.
eWhen the water level is lower than the REFILL Line and boiling
has been attempted.
eWhen the Inner Container is empty or the Upper Lid is left open for
adding water.
®When pouring in hot water immediately after plugging in the unit.
ww
Unplug the product. Allow the Inner Container
22) to cool. Fill the Inner Container with water and
\_ plug back in. J
11
12
HOW TO SET THE KEEP WARM MODE
Press the
button to
change the settings.
Each press of the button changes the position
of the " 4 " on the Display.
AEE] > IEE M2 > IE)
(Default) %
For making coffee, tea and instant noodles
208°F Keep Warm Mode
208°F is ideal for making coffee, tea and
instant noodles.
N
Select the "208" on the Display.
57 Я
QUICK
QUICK TEMP La
208
175
When the boiling process has completed, a
melody sounds, the BOIL light turns off and
the KEEP WARM light turns on.
SS
08
175
160
When the water
temperature reaches
208°F, "208" appears on
the Display.
eDepending on the altitude where the product
is used, the Keep Warm mode may be set at
205°F-207°F, in order to prevent continuous
boiling.
For making Japanese (green) tea
175°F Keep Warm Mode
175°F is ideal for making Japanese
(green) tea.
Select the "175" on the Display.
ma A
REBOIL
When the boiling process has completed, a
melody sounds, the BOIL light turns off, and
the KEEP WARM light begins to blink.
If initiated during Keep Warm mode, the light
will blink 2 seconds after the selection.
When the water 2 short beeps
temperature reaches
appears on the Display, CU
and the KEEP WARM 17514 ' LU
light stops blinking and 160
remains on.
a
about 175°F, "175"
208
В
O1
EM Length of time for the water temperature to
reach 175°F after boiling:
CD-WCC30
Approx. 1 hour and 10 minutes
CD-WCC40 | Approx. 1 hour and 10 minutes
(At a room temperature of 73* F with the Inner Container
filled to the Maximum Water Level Line.)
e The length of time for the water temperature
to reach 175°F will vary depending on the
amount of water and room temperature.
HOW TO SET THE KEEP WARM MODE
Short beep A «
You will hear 2 short beeps when 195°F
Keep Warm mode is selected.
e You can change the temperature setting
|
during Keep Warm mode.
It may start reboiling depending on the
water temperature and the selected
setting.
160°F is ideal for preparing baby formula.
Select the "160" on the Display.
When the boiling
process has
completed, a melody
sounds, the BOIL
light turns off, and
the KEEP WARM
light begins to blink.
Olf you wish to shorten
the time, add less water
to the Inner Container.
If initiated during For | For example )
Keep Warm mode,
the light will blink 2 Fill waterup to 1.0
seconds after the Gauge.
selection.
2 short beeps
x 2 times
When the water
temperature reaches
about 160°F, "160"
appears on the Display
and the KEEP WARM
light stops blinking and
remains on.
M Length of time for the water temperature to
reach 160°F after boiling:
1.0L
Approx. 1 hour
Max Capacity
CD-WCC30
CD-WCC40
Approx. 2 hours and 10 minutes
Approx. 1 hour |Approx. 2 hours and 10 minutes
(At a room temperature of 73°F.)
e The length of time for the water temperature
to reach 160°F will vary depending on the
amount of water and room temperature.
| When preparing baby formula: à
160°F is ideal for preparing formula. Dissolve the
formula and let cool to optimum temperature
(slightly higher than body temperature). If fed
without cooling, babies are at risk of scalding.
- Be sure to check that the Keep Warm light is on
and NOT blinking before dispensing.
| - Do not use the Quick Temp mode. (see pg.14)
7
@Reinsert the Power Cord if it is accidentally
detached.
elf the cord is detached for more than a few
minutes and reinserted, the product returns to
the 195*F Keep Warm mode and may start
reboiling automatically.
EB Temperature
Conversion Guide
Fahrenheit (*F) | Celsius (°C)
212 100
208 98
207 97
205 96
195 90
175 80
160 70
73 23
If the Power Cord is detached a
J
13
14
QUICK TEMP MODE
This function heats the water to the selected Keep Warm temperature without reaching a boil. The water will reach the
selected Keep Warm temperature quicker than the regular Boil mode. Other benefits include reduced steam and
reduced energy use. Use this mode when dechlorination is not necessary, such as when using bottled or purified water.
"While the water is heating,
press the button to
select the Quick Temp mode.
QUICK TEMP
You cannot activate Quick Temp mode
while the product is set at 208°F Keep
Warm mode.
After reaching the
selected temperature, it
will automatically switch
to Keep Warm.
A melody sounds, the QUICK TEMP
light turns off and the KEEP WARM
light turns on.
a
160°F Keep Warm mode:
@Once the water temperature
reaches about 175°F (80°C),
it will switch to Keep Warm
at 160°F (70°C).
Length of time for the water
temperature to reach 160°F
after heating up is approx.
G Turns off
REBOLLO
QUICK TEMP / TEMP
Short beep
use the regular Boil mode instead.
from that shown on the Display.
O
REBOIL Gm Turns 0
QUICK TEMP / TEMP
fr)
OYou cannot select 208°F Keep Warm mode while Quick Temp mode is activated.
®There may be a lingering chlorine smell if tap water is used while Quick Temp mode is activated. If this is an issue,
Regular Boil mode MES Quick Temp mode
(Default) + |
Holding the REBOIL/QUICK TEMP button for more than 3
« seconds activates Citric Acid Cleaning mode. (see pg. 17)
J
40 minutes. (At a room
temperature of 73°F / 23°C
with the Inner Container
filled to the Maximum Water
Level Line.)
O After the KEEP WARM light
stops blinking, it will switch
en
q to Keep Warm mode.
@Depending on the amount of water and room temperature the actual water temperature after heating may differ
@Depending on the amount of water, room temperature, and atmospheric pressure, some steam may be produced.
@The Quick Temp mode may be cancelled if the product is left unplugged for several minutes.
‘Each press of the REBOIL/QUICK TEMP button changes the boil mode.
NOTE
O Water does not reach a boil under Quick Temp mode,
and should not be used to prepare baby formula.
O Although the water will not reach a boil when
Quick Temp mode is activated, the Steam Vent
will become hot. Please do not touch it.
ENERGY-SAVING TIMER FUNCTION
N
The Boiling function will complete after the set time. (The Energy-Saving Timer Function helps save
energy by shutting off electricity to the heater until boiling begins.)
fes Short beep
| 3% You will hear 2 short beeps when 6H is selected. |
A melody sounds and the Energy-
Saving Timer function is activated.
ww
The Boiling function will complete
at the set time.
A melody sounds, the BOIL light turns off and
the KEEP WARM light turns on.
Boiling may stop earlier than set, depending on room
temperature, water temperature and amount of water.
sc
Press the button until the desired length of time is displayed.
Timer settings: (H for hours)
6H > 7H > 8H > 9H > 10H
y |
UP
O To cancel the Timer, press the TIMER button
several times or press the REBOIL/QUICK TEMP
button once.
@When using the Quick Temp mode with the
Energy-Saving Timer function, set the
Energy-Saving Timer function after selecting the
Quick Temp mode.
Olf the Power Cord is detached, the Energy-Saving
Timer function will be cancelled and must be
reset.
CAFE DRIP DISPENSING MODE
This mode decreases the amount of water dispensed to 60% of the normal setting, making it suitable for
brewing café drip coffee.
f A
(long bsp beep) @Pressing the UNLOCK button again during
1 Press the (moy (ког) button GI Café Drip Dispensing mode returns it to the
twice. O normal dispensing mode.
: . @When the light turns off, the Automatic
When the SAFE DRIP ght SLOW Dispense Lock will be activated.
mode le activated. p 9 Oelfihe water level is low, it may take longer
for water to begin dispensing after pressing
the DISPENSE button.
Olf the water level is low or boiling has just
completed, water may not dispense
smoothly.
Press the OBe careful not to burn yourself.
! Olf using a cone filter placed directly on a
button to dispense cup, be careful not to let it fall inside the
hot water, cup while brewing.
You can use the Са Опр ®When using a manual drip coffee cone,
Dispensing mode for about 60 dispense a cup of hot water before
seconds while the CAFE DRIP brewing, (The first cup may not be hot
light is on. enough.)
Na J
HOW TO CHANGE THE INFORMATION SOUND
e Information Sound:
The product informs you with a melody or beeps that it has finished
boiling or the timer has been set.
f в
Press the (us) button for more: Once your desired sound
than 3 seconds during the boiling : (melody or beep) is heard,
process or Keep Warm mode. : the setting is completed.
@Each button press changes the : @lf the Silent setting is selected, a beep will
Information Sound. : indicate the setting has completed.
" O The Information Sound will return to
(Default) : Melody if the product is unplugged.
Q "
Le) for more When and what types of
than 3 vo =
Information Sounds are heard:
ET. Type >
er When
than 3 seconds Boiling stops | Minuet | 5 long beeps X
Timer is set | Beautiful Dreamer X X J
Na J
16
Always unplug the Power Cord,
CLEANING AN D MAI NTENANCE dispose all water, and allow to cool
completely before cleaning.
Co dB @Do not attempt to dry the product by turning it upside down when the bottom is wet. (Water may get inside в
the body and cause it to break or rust.)
@Do not use the following:
- Thinner, benzene and bleach. (Doing so may cause discoloration, crack, degradation and corrosion.)
- Polishing powder, nylon brushes, anything made with metal, eraser pads, hard nylon sponges and abrasive cleaners. (Doing so
may cause corrosion.)
- Detergent. (Hot water may spill out, resulting in scalds or damage. Doing so may cause unwanted odor.)
@Do not use scrub brushes for any portions other than the Filter. (Doing so may cause corrosion.)
@®When using chemically treated cloths, do not rub too hard or leave them on the product for a long time as the surfaces of the
product may be damaged by chemical reactions.
ODo not use a dishwasher or dish dryer for cleaning or drying. (Doing so may cause the plastic parts to deform.)
\ @Before storing the product for a longer period of time, dry it completely and pack in a plastic bag to prevent odors from being absorbed. ›
: TE Wipe clean with a
Inner Lid Wipe with a soft wet sponge. } Body/Upper Lid damp well-wrung com.
Perform the Citric Acid Cleaning Y eDo not wash any part of the Body, Control |
LUE UCA (see pg.17) periodically. Panel or Water Level Gauge with water.
Especially when... (May cause malfunction or rust.)
®Red rust-like spotting is visible on the Inner Container.
®Milky white or gray discoloration and/or filmy objects
are found in the water.
@®Boiling is louder than usual.
®Hot water has an odor.
(The condition of the Inner Container will vary
\ depending on the water quality and frequency of use.)
Remove the Filter from the Inner \
Container and wash with a soft brush.
Pull the Filter up to release, and press
down firmly to attach.
If you find it difficult to clean the Filter, replace À
it with a new one. (see pg.17) J <=
ONever use the product without installing the Filter.
(The Filter prevents foreign objects from entering the water
\_ route or Electric Pump and obstructing the flow of hot water.) /
Power Cord Wipe clean with a dry cloth. )
he Inner Lid Gask d to be replaced d | d
HOW TO REPLACE THE INNER LID GASKET — near We recommend hat yu replace about nos a year.
Wipe new Inner Lid Gaskets with a wet soft sponge before attaching to the Inner Lid.
To remove the Inner Lid Gasket When the Inner Lid Gasket
Please purchase
(DRemove the three screws, and remove the Inner Lid. hardens, changes shape, YY and replace with
®Do not lose these screws. turns white, or otherwise a new one.
@Remove the Inner Lid Gasket which is installed on the =22222/ 0
Inner Lid. Hole onthe Screws (x3) — Rn
After removing the Inner Lid, check the plastic part of | Inner Lid Inner Lid omer Lid
the Upper Lid for abnormalities. |
—lf this part is discolored or if it feels rough to the touch, a
replace it (there will be a charge for this).
To attach the Inner Lid Gasket
(DFit the Inner Lid Gasket securely to the outer
circumference as shown in the figure.
(Line up the pin on the Upper Lid with the hole on the
Inner Lid correctly with the Upper Lid, and tighten the
three screws securely.
Inner Lid Gasket
Inner Lid
If the Inner Lid Gasket hardens, changes shape, turns white, or otherwise
becomes worn out, hot water may leak from the gap between the Upper Lid
and Body when tilted. This may result in scalds. If hot water spews from
the gap or there is steam even after replacing the Inner Lid Gasket, other
parts may be in need of repair. Please contact Zojirushi Customer Service.
Perform every 1-3 month(s) of usage
HOW TO PERFORM CITRIC ACID CLEANING
In order to prevent gas bubbles and bubbling-over, the Citric Acid Cleaner for
QP Electric Water Boilers (CD-KO3E-JU) is recommended for cleaning. To purchase
й я
Preparation:
this cleaner, please visit an authorized Zojirushi dealer or www.zojirushi.com
Check that the Filter is attached
to the Inner Container.
Do not drink
the water used
for citric acid
cleaning.
N
FOSS
CIA
UA Q © 0 СЖ
\
2 Olf the Filter is dirty, remove
ONCE
Q NAS)
it from the Inner Container,
wash with a soft brush and
reinstall.
Т Put 1 package of the Citric Acid Cleaner
CD-KO3E-JU in a cup and add warm water to CD
dissolve. Pour it into the Inner Container and
fill with water to the Maximum Water Level Line.
eDo not fill over the
Maximum Water Level
Line. (Hot water may spill
out, resulting in scalds.)
> Close the Upper Lid, insert the Power Plug and press the button for
more than 3 seconds. QUCKTEMP
| Beeps when the cleaning process begins. |
| Beeps when the cleaning process is completed.
hort beep
The square
shown on the
Display rotates. on.
2 lights will stop
blinking and stay
Unplug the Power Plug, detach the
Upper Lid and dispose water where
indicated "EMPTY FROM HERE."
(Please take precautions not to splash water
on the Hinge.)
4 To rinse, fill the Inner Container with
water. Boil and dispense about a cup of
hot water to rinse out the Spout, allow to
cool, then dispose the remaining water.
( When disposing hot water: — )
®Take precaution with the hot water and
steam. You may scald yourself.
®Take precaution as hot water may drip
from the Spout, causing scalds.
oJ
rm
o
>
г
6
H
20
rm
o
<
rm
:
=
>
„<
Cleaning time:
O 5 long beeps
A
Approx. 1.5 hours.
* Cleaning times may vary
depending on the amount
of water, water
temperature and room
temperature.
LCD display will
show a square as
illustrated.
®Repeated citric acid cleaning may
be necessary for hard-to-remove
residues or if water does not
dispense smoothly.
elf mineral or Alkalized lonic water is used,
calcium tends to build up on the surface
of the Inner Container. If scale
accumulates on the Inner Container or the
Filter, boiling may become louder than
usual and water may not dispense
smoothly. Frequent cleaning is
recommended when using mineral or
Alkalized lonic water.
To cancel the Citric Acid Cleaning at any
time, unplug the Power Plug for more
than 5 seconds.
REPLACEMENT PARTS
=
eReplacement parts may be available for an
additional charge. Please replace damaged
Parts Names Parts Number
parts only with new parts.
eWhen replacing parts, please record the model
number and part name beforehand. Then
contact Zojirushi Customer Service.
Zojirushi Customer Service
Inner Lid Gasket 625702-00
Filter 627402-00
Citric Acid Cleaner for
Electric Water Boilers CD-KO3E-JU
(1 oz. / 30 gX4 packets)
1-800-733-6270 Www.zojirushi.com
17
18
Q&A ON PRODUCT USE
Is it okay to use the product for >
heating liquids other than water?
Does the water need to be >
changed every day?
Is it okay to use mineral water >
or Alkalized lonic water?
| accidentally drank water while
performing the Citric Acid Cleaning. >
Is this harmful to my health?
Is it okay to go out while the >
product is turned on?
TROUBLESHOOTING GUIDE
Do not fill the product with any liquid other than water. It may cause
malfunction, or may overflow and cause scalding.
D pg.3
To prevent scale from building up, please change the water at least once a » pg.10
day.
Yes. However, when mineral or Alkalized lonic water is used, a floating
residue may develop or milky white substance may form on the surface of
the Inner Container. This is due to the ingredients in the water and is
> pg.9
pg.17
harmless to your health. Frequent cleaning is recommended.
Please follow the instructions shown on the package of the citric acid
cleaner CD-KO3E-JU.
ltis safe to use the product unattended as it has an Automatic Shut-Off function
(power to the heater will be automatically turned off), which will be activated once it
is empty of water. However be careful not to repeat the boiling process without filling
the Inner Container with water, as the Nonstick Coating may discolor and peel.
> pg.11
Please check the following
points before calling for service.
Condition Cause C
Power Plug is not connected to an electrical outlet. pl Connect the Power Plug. )
Water does not heat up.
Remedy )
The Quick Temp mode is selected. ( Press the REBOIL/QUICK TEMP |
Water does not boil. (Water does not reach a boil under Quick button, select the regular Boil mode.
Temp mode.) (see pg.14)
\ J
7 >
Scale or other residue has accumulated )
Hot water has a 365 ПН СЧ: Perform citric acid cleaning.
disagreeable odor. You have not performed citric acid › (see pg.17)
cleaning regularly. « J
e A mild plastic odor may be >
noticeable with a new product.
This odor will gradually fade
away.
@ You may smell chlorine (used
for sterilization of tap water)
after boiling.
The product has not been used for a long
time.
If tap water is used under Quick Temp
mode, it will take an additional 15 minutes
after boiling completes to remove up to
80% of the chlorine.
(Boil water, unlock and dispense
about 34 oz. (1 liter) of hot water.
| Discard the remaining. (see pg.9) —_,
4 в
If this is an issue, use the regular
Boil mode instead. (see pg.14)
N
Water pours out by itself from
the Spout or Steam Vent.
Check that the Inner Container is not filled
over the Maximum Water Level Line.
J
Pour out the excess water until it is
below the Maximum Water Level Line.
The Quick Temp mode cannot
be selected.
Is the 208°F Keep Warm mode selected? >
The 208°F Keep Warm mode
cannot be selected during the
Quick Temp mode.
You cannot select the 208°F Keep Warm
mode during the Quick Temp mode.
4 в
Select the 195, 175 or 160°F Keep
Warm mode, then select the Quick
› Temp mode. (see pg.14)
N J
Water does not dispense or
does not pour properly.
7
Hot water does not pour properly a few >
minutes after boiling.
\
Scale or other residue has accumulated
on the Inner Container and Filter.
The Automatic Dispense Lock is
engaged.
Scale may build up in the water route or
Electric Pump and prevent water from
dispensing smoothly.
Open the Upper Lid to release air
bubbles, then close. (Be careful of
steam when opening the Upper Lid.) )
> Clean the Inner Container and Filter.
(see pg.16)
> Press the UNLOCK button, then press
the DISPENSE button. (see pg.10)
Power Plug is not connected to an electrical outlet. > ( Connect the Power Plug.
> Perform citric acid cleaning.
(see pg.17)
Please check the following
points before calling for service.
TROUBLESHOOTING GUIDE
С
Remedy )
A filmy, floating residue is Residue is due to the mineral content in Г Perform citric acid cleaning. )
noticeable. (Could the Nonstick ETA e io ee fee o ie [e (see pg.17)
Coating be peeling off?) Container or peeling of the Nonstick Coating. S cale
Milky white and rough-surfaced | ama ea Over time and use, calcium
objects have built up on the OT amilation of scaieand and other minerals —
surface of the Inner Container. Container can cause boiling to become contained in water build up
нь ne on the surface of the Inner
Boiling is louder than usual. Container and the Filter. It is
Red rust-like spotting appears oo called "scale" and is
on the surface of the Inner Caused by iron т dhe wataf, nol й harmless to your health.
Container. J
. >
A white floating residue is Remove the Inner Lid and check the If this part is discolored or if it feels
noticeable plastic part of the Upper Lid for rough to the touch, replace it
- abnormalities. (see pg.16) J
" 77 7 >,
Initially upon boiling or if it has been a
while after dispensing, the water may not > Please discard the first cup (of the
be very hot due to water remaining in the hot water).
Water is not hot. Water Level Gauge. q
<
: Press the REBOIL/QUICK TEMP
ls the Timer set? p press (see pg.14) J
The Body becomes hot.
e When the water temperature and/or room temperature is high, the outer surface of
the Body may reach up to 140°F (60°C). This is not a malfunction.
The Power Cord becomes hot.
@ The Power Cord may become hot while the water is boiling. This is not a malfunction.
You hear a light sound when
opening and closing the Upper Lid.
water from flowing out when the product is overturned.
e This sound is normal and comes from the movement of the weight which prevents hot
Humidity builds in the Display
window.
e If water is filled from a faucet or the product is placed directly on a sink and the
bottom becomes wet, water may go inside of the Body and the Display may show
moisture. If this happens, stop using the product and allow it to dry as it may cause
short circuit or electric shock.
A beep sounds,
lights turn on and
"HH" appears on
the Display.
ir meaning
5
fend ty E
QUICK TEMP / TEMP
SS
В
160
The Inner Container is
low on water or hot water
was added to the Inner
Container, causing the
Automatic Shut-Off
function to engage.
Unplug the Power Plug and
wait until the Inner Container
cools down. Add water and
plug in the Power Cord. (see
pg.11)
2 lights blink at the + —EY
same time and the ES: mm
Display shows a N°1
rotating square.
To cancel the citric acid
cleaning cycle, unplug the
Power Plug and wait more
than 5 seconds before
plugging back in. (see pg.17)
The Inner Container is in
a citric acid cleaning >
cycle.
[2087 =
> is a
TEMPSET à 8
160
[£3 Jor] £4] is displayed. Indicates malfunction.
® The Inner Lid Gasket is replaceable, and we recommend that you replace it about
once a year. If steam leaks from the gap between the Upper Lid and the Body, or if
the Inner Lid Gasket hardens, changes shape, turns white, or otherwise becomes
worn out, please replace it. (see pg.16)
Error Displays and the
) Please contact Zojirushi Customer
Service.
Inner Lid Gasket
e The plastic part of the Upper Lid may deteriorate over use. When replacing the Inner
Lid Gasket, check the plastic part. If discoloration occurs or the surface becomes
coarse, replace the Upper Lid (must purchase separately). (We take care in only
using materials for the plastic parts that are safe and hygienic for food contact.)
Plastic Parts
Replacement for
CRY Ig Re
The Nonstick Coating of the Inner Container may become damaged over use. Contact or call Zojirushi
Customer Service at: 1-800-733-6270
19
7 ZÓJIRUSHI
www.Zojirushi.com
CD-WCC ©®