INSTALLATION INSTRUCTIONS

SLIDE-IN ELECTRIC RANGE

Table of Contents

RANGE SAFETY.......................................................................... 2

INSTALLATION REQUIREMENTS............................................. 3

Tools and Parts......................................................................... 3

Location Requirements ............................................................ 3

Electrical Requirements - U.S.A. Only ..................................... 4

Countertop Preparation............................................................ 5

INSTALLATION INSTRUCTIONS............................................... 5

Unpack Range .......................................................................... 5

Adjust Leveling Legs................................................................. 6

Install Anti-Tip Bracket ............................................................. 6

Electrical Connection - U.S.A. Only ......................................... 7

Verify Anti-Tip Bracket Is Installed and Engaged................... 12

Level Range ............................................................................ 13

Complete Installation.............................................................. 13

Moving the Range................................................................... 14

IMPORTANT:

Save for local electrical inspector's use.

W10430947A

2

RANGE SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

DANGER

You can be killed or seriously injured if you don't immediately follow instructions.

WARNING

You can be killed or seriously injured if you don't follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation instructions.

Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed and engaged.

Failure to follow these instructions can result in death or serious burns to children and adults.

Range Foot

Anti-Tip

Bracket

To verify the anti-tip bracket is installed and engaged:

• Slide range forward.

• Look for the anti-tip bracket securely attached to floor or wall.

• Slide range back so rear range foot is under anti-tip bracket.

• See installation instructions for details.

■

■

■

■

INSTALLATION REQUIREMENTS

■ Grounded electrical supply is required. See “Electrical

Requirements” section.

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed here.

Tools needed

Parts supplied

Check that all parts are included.

■ 3 - #10-32 hex nuts (attached to terminal block)

■

■

■

■

Tape measure

Level

Phillips screwdriver

Flat-blade screwdriver

3 - Terminal lugs

■

■

■

■

Wrench or pliers

³⁄₈" nut driver

Drill

¹⁄₈" (3.2 mm) drill bit

2 or 3 - Oven racks (depending on your model)

2 - #12 x 1

⁵⁄₈" screws (for mounting anti-tip bracket)

Anti-tip bracket

Anti-tip bracket must be securely mounted to back wall or floor. Thickness of floor may require longer screws to anchor bracket to subfloor. Longer screws are available from your local hardware store.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194°F (90°C).

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured

Home Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280). When such standard is not applicable, the Standard for Manufactured Home Installations,

ANSI A225.1/NFPA 501A or with local codes.

Mobile home installations require:

■ When this range is installed in a mobile home, it must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards listed above.

■ Four-wire power supply cord or cable must be used in a mobile home installation. The appliance wiring will need to be revised. See “Electrical Connection” section.

Product Dimensions

Parts needed

If using a power supply cord:

■ A UL listed power supply cord kit marked for use with ranges.

The cord should be rated at 250 volts minimum, 40 amps or

50 amps that is marked for use with nominal 1 ³⁄₈" (3.5 cm) diameter connection opening and must end in ring terminals or open-end spade terminals with upturned ends.

A

■ A UL listed strain relief.

Check local codes. Check existing electrical supply. See

“Electrical Requirements” section.

It is recommended that all electrical connections be made by a licensed, qualified electrical installer.

F

B*

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

■ It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located on the right-hand side of the oven frame behind the storage drawer panel.

■ The range should be located for convenient use in the kitchen.

■

■

■

To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided, the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

Cabinet opening dimensions that are shown must be used.

Given dimensions are minimum clearances.

The floor anti-tip bracket must be installed. To install the antitip bracket shipped with the range, see “Install Anti-Tip

Bracket” section.

E**

D

C

A.

30³⁄₄" (78.1 cm)

B. 35

³⁄₄" (90.8 cm) height to underside of cooktop edge with leveling legs screwed all the way in*

C. Model/serial number plate (located behind the storage drawer on the right-hand side of the oven frame

D. 29

⁷⁄₈" (75.9 cm)

E. 28

⁵⁄₁₆" (71.9 cm) from handle to standoff at back of range**

F. 23

³⁄₄" (60.3 cm) countertop notch to rear of cooktop

*Range can be raised approximately 1" (2.5 cm) by adjusting the leveling legs.

**When installed in a 24" (61 cm) base cabinet with 25" (63.5 cm) countertop; front of oven door protrudes 2

¹⁄₂" (6.4 cm) beyond

24" (61.0 cm) base cabinet.

3

Cabinet Dimensions

Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth and

36" (91.4 cm) countertop height.

IMPORTANT: If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood combination installation instructions for dimensional clearances above the cooktop surface.

H

F

B

A

I

G

E

C

D

I

A. 13" (33.0 cm) upper cabinet depth

B. 30" (76.2 cm) min. opening width

C. For minimum clearance to the top of the cooktop, see NOTE*.

D. 23

¹⁄₄" (59.1 cm) opening depth

E. 30" (76.2 cm) min. opening width

F. Junction box - 5.5" (14.0 cm) min. from either cabinet,

10" (25.4 cm) max. from floor

Outlet must be flush.

Nothing located in shaded area can extend more than

2" (5.1 cm) from wall or range will not slide all the way back.

G. Cabinet door or hinge should not extend into cutout.

NOTE: 24" (61.0 cm) minimum when bottom of wood or metal cabinet is covered by not less than ¹⁄₄" (0.64 cm) flame retardant millboard covered with not less than No. 28 MSG sheet steel,

0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or

0.020" (0.5 mm) copper.

30" (76.2 cm) minimum clearance between the top of the cooking platform and the bottom of an uncovered wood or metal cabinet.

Electrical Requirements - U.S.A. Only

If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path is adequate and wire gauge is in accordance with local codes.

Do not use an extension cord.

Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/

NFPA 70-latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

One Batterymarch Park

Quincy, MA 02269

WARNING: Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service technician if you are in doubt as to whether the appliance is properly grounded. Do not modify the power supply cord plug. If it will not fit the outlet, have a proper outlet installed by a qualified electrician.

This range is manufactured with the neutral terminal connected to the cabinet. Use a 3-wire, UL listed, 40-amp power supply cord (pigtail); or if local codes do not permit ground through the neutral, use a 4-wire power supply cord rated at 250 volts,

40 amps and investigated for use with ranges.

Electrical Connection

To properly install your range, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.

■ Range must be connected to the proper electrical voltage and frequency as specified on the model/serial number rating plate. (The model/serial number rating plate is located on the oven frame behind the storage drawer panel.)

■ When a 4-wire or 3-wire, single phase 120/240 volt, 60 Hz,

AC only electrical supply is available, a 50-amp maximum circuit protection is required (or, if specified on the model/ serial rating plate, when a 4-wire or 3-wire single phase

120/208 volt 60 Hz, AC only electrical supply is available, a

40- or 50-amp maximum circuit protection is required), fused on both sides of the line.

■

■

■

■

■

■

A time-delay fuse or circuit breaker is recommended.

The range can be connected directly to the fused disconnect

(or circuit breaker box) through flexible or nonmetallic sheathed, copper or aluminum cable. See “Electrical

Connection.”

Allow 2 to 3 ft (61.0 cm to 91.4 cm) of slack in the line so that the range can be moved if servicing is ever necessary.

A UL listed conduit connector must be provided at each end of the power supply cable (at the range and at the junction box).

Wire sizes and connections must conform with the rating of the range (40 amps).

The wiring diagram is located on the underside of the storage drawer or below the warming drawer in a clear plastic bag.

If using a power supply cord:

■ A UL listed power supply cord kit marked for use with ranges.

The cord should be rated at 250 volts minimum, 40 amps or

50 amps that is marked for use with nominal 1 ³⁄₈" (3.5 cm) diameter connection opening and must end in ring terminals or open-end spade terminals with upturned ends.

■ A UL listed strain relief.

4

If connecting to a 4-wire system:

This range is manufactured with the ground connected to the cabinet. The ground must be revised so the green ground wire of the 4-wire power supply cord is connected to the cabinet. See

“Electrical Connection.”

Grounding through the neutral conductor is prohibited for new branch-circuit installations (1996 NEC); mobile homes; and recreational vehicles, or an area where local codes prohibit grounding through the neutral conductor.

When a 4-wire receptacle of NEMA Type 14-50R is used, a matching UL listed, 4-wire, 250 volt, 40-amp, range power supply cord (pigtail) must be used. This cord contains 4 copper conductors with ring terminals or open-end spade terminals with upturned ends, terminating in a NEMA Type 14-50R plug on the supply end.

The fourth (grounding) conductor must be identified by a green or green/yellow cover and the neutral conductor by a white cover.

Cord should be Type SRD or SRDT with a UL listed strain relief and be at least 4 ft (1.22 m) long.

If connecting to a 3-wire system:

Local codes may permit the use of a UL listed, 3-wire,

250 volt, 40-amp range power supply cord (pigtail). This cord contains 3 copper conductors with ring terminals or open-end spade terminals with upturned ends, terminating in a NEMA Type

10-50P plug on the supply end. Connectors on the appliance end must be provided at the point the power supply cord enters the appliance. This uses a 3-wire receptacle of NEMA Type 10-50R.

3-wire receptacle (10-50R)

4-wire receptacle (14-50R)

The minimum conductor sized for the copper 4-wire power cord are:

40-amp circuit

2 No.-8 conductors

1 No.-10 white neutral

1 No.-8 green grounding

Countertop Preparation

(for Slide-in Ranges Only)

The cooktop sides of the slide-in range fit over the cutout edge of your countertop.

If you have a square finish (flat) countertop and the opening width is 30" (76.2 cm), no countertop preparation is required.

Formed front-edged countertops must have molded edge shaved flat

³⁄₈" (1.0 cm) from each front corner of opening.

Tile countertops may need trim cut back ³⁄₈" (1.0 cm) from each front corner and/or rounded edge flattened.

30"

(76.2 cm) ³⁄₈

"

(1.0 cm)

30 ¾"

(78.1 cm)

If countertop opening width is greater than 30" (76.2 cm), adjust the ³⁄₈" (1.0 cm) dimension.

Countertop must be level. Place level on countertop, first side to side, then front to back. If countertop is not level, range will not be level. Range must be level for satisfactory baking conditions.

INSTALLATION INSTRUCTIONS

WARNING

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

Unpack Range

4. Remove and discard cardboard cross support.

B

A

1. Remove shipping materials, tape and film from the range.

Keep cardboard bottom under range.

2. Remove oven racks and parts package from inside oven.

3. Pull storage drawer out completely.

A. Storage drawer

B. Cardboard cross support

5

5. To remove cardboard bottom, place range on its back, take

4 cardboard corners from the carton. Stack one cardboard corner on top of another. Repeat with the other 2 corners.

Place them lengthwise on the floor behind the range to support the range when it is laid on its back.

6. Using 2 or more people, firmly grasp the range and gently lay it on its back on the cardboard corners.

7. Pull cardboard bottom firmly to remove.

8. Use an adjustable wrench to loosen the leveling legs.

9. Place cardboard or hardboard in front of range. Using 2 or more people, stand range back up onto cardboard or hardboard.

Adjust Leveling Legs

1. If range height adjustment is necessary, use a wrench or pliers to loosen the 4 leveling legs.

This may be done with the range on its back or with the range supported on 2 legs after the range has been placed back to a standing position.

NOTE: To place range back up into a standing position, put a sheet of cardboard or hardboard in front of range. Using 2 or more people, stand range back up onto the cardboard or hardboard.

WARNING

Install Anti-Tip Bracket

1. Remove the anti-tip bracket that is taped in the storage drawer.

2. Determine which mounting method to use: floor or wall.

If you have a stone or masonry floor you can use the wall mounting method.

3. Determine and mark centerline of the cutout space. The mounting bracket can be installed on either the left side or right side of the cutout. Position mounting bracket in cutout so that right (or left) edge of the bracket is 14 ¹⁄₄" (36.2 cm) from centerline, as shown.

A

B

A. Centerline

B. 14 ¹⁄₄" (36.2 cm)

4. Drill two ¹⁄₈" (3 mm) holes that correspond to the bracket holes of the determined mounting method. See below.

Floor Mounting

A B

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation instructions.

Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed and engaged.

Failure to follow these instructions can result in death or serious burns to children and adults.

A. #12 x 1

⁵⁄₈" screws

B. Anti-tip bracket

Wall Mounting

2. Adjust the leveling legs to the correct height. Leveling legs can be loosened to add up to a maximum of 1" (2.5 cm). A minimum of ³⁄₁₆" (5 mm) is needed to engage the anti-tip bracket.

NOTE: If height adjustment is made when range is standing, tilt the range back to adjust the front legs, then tilt forward to adjust the rear legs.

3. When the range is at the correct height, check that there is adequate clearance under the range for the anti-tip bracket.

Before sliding range into its final location, check that the antitip bracket will slide under the range and onto the rear leveling leg prior to anti-tip bracket installation.

A

B

A. #12 x 1

⁵⁄₈" screws

B. Anti-tip bracket

5. Using the Phillips screwdriver, mount anti-tip bracket to the wall or floor with the two #12 x 1

⁵⁄₈" screws provided.

6

Power Supply Cord

Electrical Connection - U.S.A. Only

Direct Wire

WARNING WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Use a new 40 amp power supply cord.

Plug into a grounded outlet.

Failure to follow these instructions can result in death, fire, or electrical shock.

1. Disconnect power.

2. Use Phillips screwdriver to remove the terminal block cover screw located on the back of the range. Pull cover down and toward you to remove cover.

Electrical Shock Hazard

Disconnect power before servicing.

Use 8 gauge copper or 6 gauge aluminum wire.

Electrically ground range.

Failure to follow these instructions can result in death, fire, or electrical shock.

Style 1: Power supply cord strain relief

■ Assemble a UL listed strain relief in the opening.

A

3. Remove plastic tag holding three 10-32 hex nuts from the middle post of the terminal block.

A. UL listed strain relief

■

■

Feed the power supply cord through the opening in the cord/conduit plate on bottom of range. Allow enough slack to easily attach the wiring to the terminal block.

Tighten strain relief screw against the power supply cord.

4. Add strain relief.

7

8

Style 2: Direct wire strain relief

■ Use Phillips screwdriver to remove screws from panel on back of range.

■ Replace cord/conduit plate and insert screws.

G! TA US RD CO ER CO RD G! TA ER US RD CO ER

TS NU H P WIT TS NU RE MO LA ITE IQU ET H P WIT OW R E TS NU RE MO ER CA TU ETA LA ITE IQU ET H P OW WIT OW R E ETA

CO RA CTA NE ICO US QU AS E L ÉC EL ÓN CTA CO NE QU RA ÉC ICO ÓN EL

CO RD CO RD

■ Assemble a UL listed conduit connector in the opening.

■ Lift range back panel up and off.

AG E T IQU ETA RD H P OW CO ER CO RD OW ER REM H P AG E T IQU ETA CO RD REM H P OW ER

LA ITE NE ET QU WIT TS NU CTA NE ICO R E AS E L TU CA LA ET ICO QU ITE TS WIT NU WIT TS NU CTA R E

CO CO RA EL ÓN RD CO CO US RA EL ÓN RD

■ Use Phillips screwdriver to remove screws and slide cord/conduit plate down and out.

A

B

■

■

A. Removable retaining nut

B. Strain relief

Feed the flexible conduit through the strain relief, allowing enough slack to easily attach wiring to the terminal block.

Tighten strain relief screw against the flexible conduit.

■ Position cord/conduit plate as shown in the following illustration.

5. Replace back panel and screws on rear of range.

6. Complete installation following instructions for your type of electrical connection:

4-wire (recommended)

3-wire (if 4-wire is not available)

Electrical Connection Options

If your home has:

4-wire receptacle

(NEMA type 14-50R)

And you will be connecting to:

A UL listed,

250-volt minimum,

40-amp, range power supply cord

Go to Section:

4-wire connection:

Power supply cord

4-wire direct A fused disconnect or circuit breaker box

4-wire connection:

Direct wire

5"

(12.7 cm)

3-wire receptacle

(NEMA type 10-50R)

A UL listed,

250-volt minimum,

40-amp, range power supply cord

3-wire connection:

Power supply cord

3-wire direct

1"

(2.5 cm)

A fused disconnect or circuit breaker box

3-wire connection:

Direct wire

3"

(7.6 cm)

4-wire connection: Power Supply Cord

Use this method for:

■ New branch-circuit installations (1996 NEC)

■

■

Mobile homes

Recreational vehicles

■ In an area where local codes prohibit grounding through the neutral

1. Part of metal ground strap must be cut out and removed.

A

B

C

A. Metal ground strap

B. Discard

C. Ground-link screw

2. Use Phillips screwdriver to remove the ground-link screw from the back of the range. Save the ground-link screw and the end of the ground-link under the screw.

3. Feed the power supply cord through the opening in the cord/ conduit plate on bottom of range. Allow enough slack to easily attach the wiring to the terminal block.

A

C

D

B

A. Terminal block

B. Ground-link screw

C. Cord/conduit plate

D. Power supply cord wires

4. Use Phillips screwdriver to connect the green ground wire from the power supply cord to the range with the ground-link screw. The ground wire must be attached first.

5. Use ³⁄₈" nut driver to connect the neutral (white) wire to the center terminal block post with one of the 10–32 hex nuts.

A

F

B

E

C

A. 10–32 hex nut

B. Ground-link screw

C. Line 1 (black)

D

D. Green ground wire

E. Neutral (center) wire

F. Line 2 (red)

6. Connect line 1 (black) and line 2 (red) wires to the outer terminal block posts with 10-32 hex nuts.

7. Securely tighten hex nuts.

NOTE: For power supply cord replacement, only use a power cord rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1 ³⁄₈" (3.5 cm) diameter connection opening, with ring terminals and marked for use with ranges.

8. Replace terminal block access cover.

9

3-wire connection: Power Supply Cord

Use this method only if local codes permit connecting chassis ground conductor to neutral wire of power supply cord.

1. Feed the power supply cord through the opening in the cord/ conduit plate on bottom of range. Allow enough slack to easily attach the wiring to the terminal block.

Direct Wire Installation: Copper or Aluminum Wire

This range may be connected directly to the fuse disconnect or circuit breaker box. Depending on your electrical supply, make the required 3-wire or 4-wire connection.

1. Strip outer covering back 3" (7.6 cm) to expose wires. Strip the insulation back 1" (2.5 cm) from the end of each wire.

1"

(2.5 cm)

A

C

D

B

A. Terminal block

B. Ground-link screw

C. Cord/conduit plate

D. Power supply cord wires

2. Use

³⁄₈" nut driver to connect the neutral (white) wire to the center terminal block post with one of the 10–32 hex nuts.

3"

(7.6 cm)

2. Allow enough slack in the wire to easily attach the wiring terminal block.

3. Complete electrical connection according to your type of electrical supply (4-wire or 3-wire connection).

4-wire Connection: Direct Wire

Use this method for:

■ New branch-circuit installations (1996 NEC)

■ Mobile homes

■

■

Recreational vehicles

In an area where local codes prohibit grounding through the neutral

1. Part of metal ground strap must be cut out and removed.

A

E

A

B

C

D

B

C

A. 10–32 hex nut

B. Line 1 (black)

C. Ground-link screw

D. Neutral (white) wire

E. Line 2 (red)

3. Connect line 1 (black) and line 2 (red) wires to the outer terminal block posts with 10-32 hex nuts.

4. Securely tighten hex nuts.

NOTE: For power supply cord replacement, only use a power cord rated at 250 volts minimum, 40 amps or 50 amps that is marked for use with nominal 1 ³⁄₈" (3.5 cm) diameter connection opening, with ring terminals and marked for use with ranges.

5. Replace terminal block access cover.

A. Metal ground strap

B. Discard

C. Ground-link screw

2. Use Phillips screwdriver to remove the ground-link screw from the back of the range. Save the ground-link screw and the end of the ground-link under the screw.

10

3. Pull the conduit through the strain relief on cord/conduit plate on bottom of range. Allow enough slack to easily attach wiring to the terminal block.

5. Use Phillips screwdriver to connect the bare (green) ground wire to the range with the ground-link screw. The ground wire must be attached first and must not contact any other terminal.

6. Use ³⁄₈" nut driver to connect the neutral (white) wire to the center terminal block post with one of the 10–32 hex nuts.

A

G

A

B

C

G

D

F

E

A. Terminal block

B. Ground-link screw

C. Cord/conduit plate

D. Line 2 (red) wire

E. Neutral (white) wire

F. Line 1 (black) wire

G. Bare (green) ground wire

4. Attach terminal lugs to line 1 (black), neutral (white), and line 2

(red) wires. Loosen (do not remove) the setscrew on the front of the terminal lug and insert exposed wire end through bottom of terminal lugs. Securely tighten setscrew to torque as shown in the following Bare Wire Torque Specifications chart.

A

B

F

C

A. 10–32 hex nut

B. Line 1 (black)

C. Bare (green) ground wire

D. Ground-link screw

D

E

E. Neutral (white) wire

F. Line 2 (red)

G. Terminal lug

7. Connect line 1 (black) and line 2 (red) wires to the outer terminal block posts with 10-32 hex nuts.

8. Securely tighten hex nuts.

9. Replace terminal block access cover.

3-wire connection: Direct Wire

Use this method only if local codes permit connecting ground conductor to neutral supply wire.

1. Pull the conduit through the hole and conduit plate on bottom of range. Allow enough slack to easily attach the wiring to the terminal block.

B

A

C D E

B

A. Terminal lug

B. Setscrew

C. Line 1 (black) wire

D. Neutral (white) wire

E. Line 2 (red) wire

Bare Wire Torque Specifications

Attaching terminal lugs to the terminal block - 20 lbs-in. (2.3 N-m)

Wire Awg Torque

8 gauge copper

6 gauge aluminum

25 lbs-in. (2.8 N-m)

35 lbs-in. (4.0 N-m)

C

D

F

E

A. Terminal block

B. Ground-link screw

C. Cord/conduit plate

D. Line 2 (red) wire

E. Bare (green) ground wire

F. Line 1 (black) wire

11

2. Attach terminal lugs to line 1 (black), bare (green) ground, and line 2 (red) wires. Loosen (do not remove) the setscrew on the front of the terminal lug and insert exposed wire end through bottom of terminal lugs. Securely tighten setscrew to torque as shown in the following Bare Wire Torque Specifications chart.

A

B

Verify Anti-Tip Bracket Is Installed and

Engaged

On models with a storage drawer:

1. Remove the storage drawer. See the “Unpack Range” section.

2. Use a flashlight to look underneath the bottom of the range.

3. Visually check that the rear range foot is inserted into the slot of the anti-tip bracket.

On models with a warming drawer:

1. Place the outside of your foot against the bottom front of the warming drawer to keep the range from moving, and grasp the control panel with two hands as shown.

C D E

A. Terminal lug

B. Setscrew

C. Line 1 (black) wire

D. Bare (green) ground wire

E. Line 2 (red) wire

Bare Wire Torque Specifications

Attaching terminal lugs to the terminal block - 20 lbs-in. (2.3 N-m)

Wire Awg Torque

8 gauge copper

6 gauge aluminum

25 lbs-in. (2.8 N-m)

35 lbs-in. (4.0 N-m)

3. Use ³⁄₈" nut driver to connect the bare (green) ground wire to the center terminal block post with one of the 10–32 hex nuts.

B

A

F

E

D

C

A. 10–32 hex nut

B. Line 1 (black)

C. Ground-link screw

D. Bare (green) ground wire

E. Line 2 (red)

F. Terminal lug

4. Connect line 1 (black) and line 2 (red) wires to the outer terminal block posts with 10-32 hex nuts.

5. Securely tighten hex nuts.

6. Replace terminal block access cover.

2. Slowly attempt to tilt the range forward.

If you encounter immediate resistance, the range foot is engaged in the anti-tip bracket.

3. If the rear of the range lifts more than ½" (1.3 cm) off the floor without resistance, stop tilting the range and lower it gently back to the floor. The range foot is not engaged in the anti-tip bracket.

IMPORTANT: If there is a snapping or popping sound when lifting the range, the range may not be fully engaged in the bracket.

Check to see if there are obstructions keeping the range from sliding to the wall or keeping the range foot from sliding into the bracket. Verify that the bracket is held securely in place by the mounting screws.

4. Slide the range forward, and verify that the anti-tip bracket is securely attached to the floor or wall.

5. Slide range back so the rear range foot is inserted into the slot of the anti-tip bracket.

IMPORTANT: If the back of the range is more than 2" (5.1 cm) from the mounting wall, the rear range foot may not engage the bracket. Slide the range forward and determine if there is an obstruction between the range and the mounting wall. If you need assistance or service, refer to the “Assistance or Service” section of the Use and Care Guide, or the cover or “Warranty” section of the User Instructions, for contact information.

6. Repeat steps 1 and 2 to ensure that the range foot is engaged in the anti-tip bracket.

If the rear of the range lifts more than ½" (1.3 cm) off the floor without resistance, the anti-tip bracket may not be installed correctly. Do not operate the range without anti-tip bracket installed and engaged. Please reference the “Assistance or

Service” section of the Use and Care Guide, or the cover or

“Warranty” section of the User Instructions, to contact service.

12

1. Place rack in oven.

Level Range

2. Place level on rack and check levelness of range, first side to side; then front to back.

3. If range is not level, pull range forward until rear leveling leg is removed from the anti-tip bracket.

4. Use wrench to adjust leveling legs up or down until range is level. Push range back into position.

5. Check that rear leveling leg is engaged in anti-tip bracket.

NOTE: Range must be level for satisfactory baking performance.

Complete Installation

1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check that the range is level. See “Level Range.”

5. Use a mild solution of liquid household cleaner and warm water to remove waxy residue caused by shipping material.

Dry thoroughly with a soft cloth. or more information, read the

“Range Care” section of the Use and Care Guide or User

Instructions.

6. Read the “Range Use” section in the range Use and Care

Guide or User Instructions.

7. Plug power cord into appropriate outlet. Slide range into its final location.

8. Replace storage drawer (warming drawer on some models).

9. Turn on surface burners and oven. See the Use and Care

Guide or User Instructions for specific instruction on range operation.

If range does not operate, check the following:

■ Household fuse is intact and tight; or circuit breaker has not tripped.

■

■

■

Range is plugged into an outlet.

Electrical supply is connected.

See the “Troubleshooting” section in the Use and Care Guide or User Instructions.

When the range has been on for 5 minutes, check for heat. If range is cold, turn off the range and contact a qualified technician.

If you need Assistance or Service:

Please reference the “Assistance or Service” section of the Use and Care Guide, or the cover of the User Instructions, or contact the dealer from whom you purchased your range.

13

WARNING

Moving the Range

For direct-wired ranges:

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Install anti-tip bracket to floor or wall per installation instructions.

Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.

Re-engage anti-tip bracket if range is moved.

Do not operate range without anti-tip bracket installed and engaged.

Failure to follow these instructions can result in death or serious burns to children and adults.

When moving range, slide range onto cardboard or hardboard to avoid damaging the floor covering.

If removing the range is necessary for cleaning or maintenance:

For power supply cord-connected ranges:

1. Slide range forward.

2. Unplug the power supply cord.

3. Complete cleaning or maintenance.

4. Plug in power supply cord.

5. Slide range back so rear range foot is under anti-tip bracket.

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

1. Disconnect power.

2. Slide range forward.

3. Complete cleaning or maintenance.

4. Slide range back so rear range foot is under anti-tip bracket.

5. Refer to the “Verify Anti-Tip Bracket Is Installed and

Engaged” section to verify engagement.

6. Check that range is level.

7. Reconnect power.

6. Refer to the “Verify Anti-Tip Bracket Is Installed and

Engaged” section to verify engagement.

7. Check that range is level.

14

Notes

15

W10430947A

© 2011. Whirlpool Corporation.

All rights reserved.

10/11

Printed in U.S.A.