SI Products

Service Center

1.888.856.6781

8:30a.m. – 7:00p.m. (EST)

M – F

Mail To:

SI Products

Consumer Relations

Service Center Dept. 168

3000 Pontiac Trail

Commerce Township, MI

48390 e-mail: [email protected]

ONE YEAR LIMITED WARRANTY

SI PRODUCTS sells its products with the intent that they are free of defects in manufacture and workmanship for the life of the original purchaser from the date of original purchase, except as noted below. SI PRODUCTS warrants that its products will be free of defects in material and workmanship under normal use and service. This warranty extends only to consumers and does not extend to

Retailers.

To obtain warranty service on your SI PRODUCTS product, mail the product and your dated sales receipt (as proof of purchase), postpaid, to the following address:

SI PRODUCTS Consumer Relations

Service Center Dept. 168

3000 Pontiac Trail

Commerce Township, MI 48390

No COD's will be accepted.

SI PRODUCTS does not authorize anyone, including, but not limited to, Retailers, the subsequent consumer purchaser of the product from a Retailer or remote purchasers, to obligate SI PRODUCTS in any way beyond the terms set forth herein. This warranty does not cover damage caused by misuse or abuse; accident; the attachment of any unauthorized accessory; alteration to the product; improper installation; unauthorized repairs or modifications; improper use of electrical/power supply; loss of power; dropped product; malfunction or damage of an operating part from failure to provide manufacturer’s recommended maintenance; transportation damage; theft; neglect; vandalism; or environmental conditions; loss of use during the period the product is at a repair facility or otherwise awaiting parts or repair; or any other conditions whatsoever that are beyond the control of SI

PRODUCTS.

This warranty is effective only if the product is purchased and operated in the country in which the product is purchased. A product that requires modifications or adoption to enable it to operate in any other country than the country for which it was designed, manufactured, approved and/or authorized, or repair of products damaged by these modifications is not covered under this warranty.

THE WARRANTY PROVIDED HEREIN SHALL BE THE SOLE AND EXCLUSIVE WARRANTY. THERE

SHALL BE NO OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTY OF

MERCHANTABILITY OR FITNESS OR ANY OTHER OBLIGATION ON THE PART OF THE COMPANY WITH

RESPECT TO PRODUCTS COVERED BY THIS WARRANTY. SI PRODUCTS SHALL HAVE NO LIABILITY FOR

ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES. IN NO EVENT SHALL THIS WARRANTY

REQUIRE MORE THAN THE REPAIR OR REPLACEMENT OF ANY PART OR PARTS WHICH ARE FOUND TO

BE DEFECTIVE WITHIN THE EFFECTIVE PERIOD OF THE WARRANTY.

NO REFUNDS WILL BE GIVEN. IF REPLACEMENT PARTS FOR DEFECTIVE MATERIALS ARE NOT

AVAILABLE, SI PRODUCTS RESERVES THE RIGHT TO MAKE PRODUCT SUBSTITUTIONS IN LIEU OF

REPAIR OR REPLACEMENT.

This warranty does not extend to the purchase of opened, used, repaired, repackaged and/or resealed products, including but not limited to sale of such products on Internet auction sites and/or sales of such products by surplus or bulk resellers. Any and all warranties or guarantees shall immediately cease and terminate as to any products or parts thereof which are repaired, replaced, altered, or modified, without the prior express and written consent of SI PRODUCTS.

This warranty provides you with specific legal rights. You may have additional rights which may vary from state to state. Because of individual regulations, some of the above limitations and exclusions may not apply to you.

For more information regarding our product line in the USA, please visit: www.siproducts.com

For service or repair - do not return this unit to the retailer.

Contact SI PRODUCTS Consumer Relations at 1-888-856-6781.

©The Sharper Image. All rights reserved. THE SHARPER IMAGE name and logo are registered trademarks.

©2009 THE SHARPER IMAGE and its affiliated companies, all rights reserved. THE SHARPER IMAGE is a registered trademark of THE SHARPER IMAGE and its affiliated companies.

EC-PJ10

Portable

Media Projector

Instruction Manual and

Warranty Information EC-PJ10

Super-size your fun.

Thank you for purchasing The Sharper Image® Portable Media Projector.

This product, along with the entire The Sharper Image collection, connects innovation with cutting-edge design to provide you with years of dependability and enjoyment. For those who want to pump up there TV and movie watching or video game playing, the portable media projector, from The Sharper Image, delivers a large, sharp image that will surely increase your viewing pleasure.

IMPORTANT SAFEGUARDS:

WHEN USING ELECTRICAL PRODUCTS, ESPECIALLY WHEN CHILDREN ARE PRESENT,

BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE

FOLLOWING:

READ ALL INSTRUCTIONS BEFORE USING

DANGER

- To reduce the risk of electric shock:

• Always unplug the appliance from the electrical outlet immediately after using

and before cleaning.

• DO NOT reach for an appliance that has fallen into water. Unplug it immediately.

• DO NOT use while bathing or in shower.

• DO NOT place or store appliance where it can fall or be pulled into a tub

or sink.

• DO NOT place in or drop into water or other liquid.

• NEVER use pins or other metallic fasteners with this appliance.

• Keep dry - DO NOT operate in a wet or moist condition

2

Caution: All servicing of this product must be performed by authorized

SI Products

Service

Personnel only.

WARNING

To reduce the risk of burns, fire, electric shock or injury to persons:

• An appliance should never be left unattended when plugged in.

Unplug from outlet

when not in use and before putting on or taking off parts or attachments.

• Close supervision is necessary when this appliance is used by, on or near children, invalids or disabled persons.

• Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended

by The Sharper Image; specifically any attachments not provided with the unit.

• NEVER operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or

damaged, or dropped into water. Return it to SI Products Service

Center for examination and repair.

• Keep cord away from heated surfaces.

• NEVER drop or insert any object into any opening.

• DO NOT operate where aerosol (spray) products are being used or where oxygen is being administered.

• DO NOT operate under a blanket or pillow. Excessive heating can occur and cause fire, electric shock or injury to persons.

• DO NOT carry this appliance by the power cord or use cord as handle.

• To disconnect, turn all controls to the “off” position, then remove plug from outlet.

• This appliance is designed for personal, non-professional use only.

• DO NOT use outdoors.

SAVE THESE INSTRUCTIONS

3

EC-PJ10_Media Projector.ai 7/6/09 11:28:50 PM

EC-PJ10_Jacks.ai 7/7/09 2:04:08 PM

EC-PJ10_Buttons.ai 7/6/09 11:04:42 PM

Projector side view

Input jacks

4

Control panel

Media Projector - Operation Instructions

1) Set up and Installation

Carefully remove the projector from the box. Make sure you have removed all the parts in the package. Be sure to read the instruction manual thoroughly before getting started with the projector set-up.

• Position the projector on a flat surface up to 6ft. (72”) from the surface on

which you want to project.

• The projector can be projected onto a screen, a light-colored wall or ceiling

using the provided stand.

• Plug the projector into an electric outlet and check to be sure plug is inserted

correctly. CAUTION: Loose connecting plugs may cause ELECTRIC SHOCK.

• Connect the projector to the source using the supplied cables. (red and

white for audio; yellow for video).

NOTE: For better sound quality, connect the audio cables (red and white)

to an external sound system.

• Once projector is powered on, the fan and the lamp will run. An introductory

screen will appear on the viewing surface.

WARNING: Do not place the projector on a carpeted or upholstered surface to avoid fire.

2) Operation

CAUTION: To reduce the risk of electric shock, this appliance is equipped with a polarized plug (one blade wider than the other). This pug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.

• Plug projector into main outlet.

• Press the “POWER” button located on top of the projector to turn on.

• Adjust the stand to make sure the image is projected evenly onto the viewing surface.

• Adjust the focus by turning the lens bezel housing clockwise or

counter-clockwise until you have a sharp viewing image.

• Adjust contrast with the contrast control button located on top of projector.

• Adjust color saturation with the color control button located on top of the projector.

• You can now enjoy your favorite DVD or video games.

• Control the volume with the volume control button located on top of the projector.

• You may also use remote to control volume, contrast and color.

WARNING – Switch off the main power button of the unit when not in use.

5

3) Maintenance

• To clean the lens, first blow away dust particles with clean and dry air to avoid

scratching the lens surface.

• Do not use any type of fluid or cleaner on the lens surface as they might

damage the lens coating.

• To replace the light bulb, follow all the steps completely below:

– Turn off the projector, DO NOT unplug, and allow it to cool for

30 minutes; red light will be blinking and fan will be running during this

time as it runs at an extremely high temperature! WARNING – RISK OF

DAMAGE. DO NOT UNPLUG WHILE THE RED LIGHT IS BLINKING AND THE FAN

IS RUNNING.

– Remove the screws and then remove the back cover of the projector to

access the light bulb.

– Make sure the bulb has cooled down. With a dry cloth, remove the

existing bulb.

– Put in the new bulb, using a clean dry cloth. DO NOT touch new bulb

with fingers as oil from your hands may damage bulb. Make sure it is well

connected to the socket.

– Use a standard 60Watt, 12V, MR-16 halogen light bulb.

– Make sure bulb is securely screwed in otherwise the projector will not

turn on or may cause electronic shock.

To Clean

Unplug the projector and allow it to cool before cleaning. Spot clean only with a soft dry cloth. Never allow water or any other liquids to come into contact with the unit.

Do not immerse in any liquid to clean

Never use abrasive cleaners, brushes, gasoline, kerosene, glass/furniture polish or paint thinner to clean.

Do not attempt to repair the Projector. There are no user serviceable parts. For service, send the projector to the Sharper Image address listed in the warranty section.

To Store

Place the projector in its box or in a safe, dry, cool place. To avoid breakage, do not wrap the power cord around the unit. Do not hang the projector by the power cord.

6

Note: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

4) Trouble Shooting

If there are no images or sound –

• Double check that the power and source connections are secured.

• Make sure the projector is turned on and volume is turned up.

• Try unplugging the power for 30 seconds, then reconnect and restart the

projector again.

• If there is still no image, check and replace the light bulb. (See maintenance)

If the image is not sharp –

• Adjust the manual lens focus. Do this with a still projected image.

• Make sure the projection distance and size and correct.

• Double check that the incoming signal from connector is good.

• Go to the set-up mode to adjust contrast and color if needed.

• Check and clean the lens if needed.

If the image is not in the correct shape (Rectangular) –

• Check that the video source is plugged in correctly.

• Make sure the projector is perpendicularly projecting to the wall or screen.

• Make sure the projector is placed on a rigid & flat surface, not a soft and (or)

sloped surface

7