Shure SCL3 User guide

SCL3

Sound Isolating Earphones

WEARING THE EARPHONES

Three popular methods for wearing the earphones are illustrated below.

With a sleek, low profile design, the SCL3 combines WideBand

MicroDriver technology and incredible sound isolation for detailed highs and enhanced bass across an extended frequency soundstage.

Originally designed for the demanding audio specifications of professional musicians, the SCL3 is an ideal choice for any home or portable audio device.

Printed in U.S.A.

©2007, Shure Incorporated

27EN3249 (Rev. 1)

CHOOSING AN EARPHONE SLEEVE

Your earphones come with a selection of sleeves. Make sure the sleeve you use is easy to insert into your ear, fits comfortably, and is easy to remove from your ear.

Soft Flex Sleeves

In small, medium, and large sizes. Made from pliable rubber.

�

Over the ear in back

Over the ear in front

Straight down

Tighten the cable and take up slack by raising the cable sleeve .

CLEANING THE EARPHONE NOZZLE

If the nozzle of your earphone is blocked, clean the nozzle using the supplied wax removal loop.

Wax Removal Loop

Nozzle

Yellow and Soft Black Foam Sleeves

When using the foam sleeves, compress the sleeve between your fingers before inserting it into the ear canal. Hold the earphone in place for about ten seconds while the foam expands and creates a tight seal. Black foams come in small, medium and large sizes.

When cleaning, do not force any object through the earphone nozzle! This will damage the earphone sound filter.

Warning: The wax removal loop is only to be used to clean earphones. Any other use, such as using the tool to clean ears, could result in injury.

Triple-Flange Sleeves (Optional Accessory)

If desired, the sleeve nozzle may be shortened. Use sharp scissors to carefully trim the nozzle to the desired length.

Note: slide sleeve over earphone nozzle barb for a secure grip.

INSERTING THE EARPHONES

If the earphone seems to be lacking in low frequency response (bass), check the tightness of the seal between the earphone and your ear, or try one of the other sleeve options.

Warning: Do not push the earphone sleeve beyond the ear canal opening.

Nozzle Barb Sleeve left ear right ear

To change earphone sleeve, twist and pull sleeve to remove it from the nozzle. Push new sleeve onto nozzle until you feel it slide completely over barb. If any part of the nozzle is exposed, sleeve is not properly installed. Replace sleeves if they do not grip the nozzle tightly.

Sleeve Over Barb

SHURE Incorporated http://www.shure.com

United States, Canada, Latin America, Caribbean:

5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.

Phone: 847-600-2000 U.S. Fax: 847-600-1212 Int’l Fax: 847-600-6446

Europe, Middle East, Africa:

Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414

Asia, Pacific:

Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055

MAINTENANCE

Careful maintenance ensures a tight seal between the sleeve and nozzle, improving sound quality and product safety.



Keep the earphones and sleeves as clean and dry as possible.



To clean sleeves, remove them from earphones, gently rinse in warm water and air dry. Foam sleeves require a longer drying time. Inspect for damage and replace if necessary.

Ear sleeves must be completely dry before reusing.

 Wipe the earphones and sleeves with mild antiseptic to avoid infections.

Do not use alcohol-based disinfectants.

 Do not expose earphones to extreme temperatures.

 Replace sleeves if they do not fit properly.

x

Do not attempt to modify this product. Doing so will void the warranty and could result in personal injury and/or product failure.

FURNISHED ACCESSORIES

• Deluxe Carrying Case

• Fit Kit: contains foam, soft flex and triple flange sleeves plus cleaning tool

ACCESSORIES

For information about earphone accessories (listed below) and other Shure products visit: www.shure.com

• Replacement Sleeves

• Carrying Cases

• Adapters

• Extension Cables

• Push To Hear (PTH)

• Volume Control

TECHNICAL SPECIFICATIONS

Transducer type

Sensitivity (at 1kHz)

Impedance (at 1kHz)

Output connector

Cable length

Net weight

Low mass/high energy

113.5 dB SPL/mW

29 W

Gold-plated 3.5 mm (1/8-inch) stereo plug

GR -157 cm (62”)

W -157 cm (62”)

K -141 cm (56”)

28 g (0.9 oz)

CUSTOM EARPHONE SLEEVES

Those who use earphones regularly for extended periods of time often find custom-fit molded sleeves offer the best comfort and sound isolation.

Ask a Hearing Health Care Professional about creating custom molded sleeves for your earphones. For more information, contact:

CERTIFICATION

Eligible to bear CE marking.

Conforms to European EMC Directive 89/336/EEC.

Meets applicable tests and performance criteria in European Standard

EN 55103 (1996) Parts 1 and 2, for residential (E1) and light industrial (E2) environments.

Sensaphonics Hearing Conservation Toll Free: (877) 848-1714

660 N. Milwaukee Avenue In Chicago: (312) 432-1714 (ph)

Chicago, IL 60622 e-mail:[email protected]

www.sensaphonics.com