Mira Play User guide


Add to my manuals
36 Pages

advertisement

Mira Play User guide | Manualzz

9.5 kW

ELECTRIC SHOWER

Installation & User Guide

THESE INSTRUCTIONS ARE TO BE LEFT WITH THE USER

1

Contents

Section Page

Introduction..................................................................................... 3

Important Safety Information ............................................... 4

Pack Contents Checklist ........................................................ 6

Specifications ........................................................................... 7

Installer Instructions .................................................................. 8

Installation .....................................................................................12

Commissioning ........................................................................... 16

User Instructions........................................................................... 18

Fault Diagnosis ........................................................................... 23

Maintenance ........................................................................... 28

Dimensions .................................................................................... 30

Wiring Diagram .......................................................................... 31

Accessories - Mira DCV-H ....................................................... 32

Spare Parts ................................................................................... 32

Guarantee, Customer Care Policy, and How to contact us

................................................................. Back Cover

2

Introduction

Thank you for purchasing a quality Mira product. To enjoy the full potential of your new product, please take time to read this guide thoroughly. Having done so, keep it handy for future reference.

The Mira Play is an electric shower with separate controls for power selection and temperature/flow adjustment. A unique flow regulator stabilizes temperature changes caused by water pressure fluctuations. These can result from taps being turned on or off, or toilets being flushed. An individual light indicates “POWER ON”.

This shower comes complete with a set of Mira Response Adjustable Shower Fittings.

Mira Play models covered by this guide:

Mira Play 9.5 kW- A 9.5 kW 240 V AC (8.3 kW 230 V AC) heater. Available in white/ white panel, white/chrome panel and satin/chrome panel finishes.

Mira Shower Fittings covered by this guide:

Mira Response Adjustable Shower Fittings

An adjustable spray handset with three different spray actions (start, soothe and force), supplied complete with flexible hose, clamp bracket assembly, slide bar, supports, soap dish, and hose retaining ring. Available in white/chrome finish.

If you experience any difficulty with the installation or operation of your new shower control, then please refer to the Fault Diagnosis section before contacting Kohler Mira

Ltd. Our telephone and fax numbers can be found on the back cover of this guide.

3

Important Safety Information

1.Warning!

1.1. Products manufactured by us are safe and without risk provided they are installed, used and maintained in good working order in accordance with our instructions and recommendations.

1.2. THIS APPLIANCE MUST BE EARTHED. MAKE SURE SUPPLEMENTARY

BONDING COMPLIES WITH THE “REQUIREMENTS FOR ELECTRICAL

INSTALLATIONS”.

The installation must be in accordance with the current edition of BS 7671 “The

IEE Wiring Regulations” in force at the time of installation. This appliance is intended to be permanently connected to the fixed electrical wiring of the mains system with its own dedicated supply.

1.3. DO NOT twist the individual cable cores of the live and neutral conductors, as this will prevent them from entering the terminal block.

1.4. The shower unit must NOT be fitted where it may be exposed to freezing conditions.

Make sure that any pipework that could become frozen is properly insulated.

1.5. DO NOT fit any form of outlet flow control as the outlet acts as a vent for the tank body. Only Mira recommended outlet fittings should be used.

1.6. If the cover is removed, the following warnings must be observed:

1.6.1.Turn off the electrical and water supplies before removing the cover.

1.6.2.Mains connections are exposed when cover is removed.

1.6.3.Refer to the wiring diagram before making any electrical connections (see section “Wiring Diagram”).

1.6.4.Ensure all electrical connections are tight, to prevent them overheating.

4

2. Caution!

2.1. Follow all warnings, cautions and instructions contained in this guide, and on or inside the appliance.

2.2. The electrical installation must comply with the “Requirements for Electrical

Installations”, commonly referred to as BS 7671 the “IEE Wiring Regulations”. Or any particular regulations and practices, specified by the local electricity supply company in force at the time of the installation. The installation should be carried out by an electrician or contractor who is “Part P” (Building Regulations) registered, or is a member of an association such as:

2.2.1.National Inspection Council for Electrical Installation and Contracting

(NICEIC), throughout the UK.

2.2.2.The Electrical Contractors Association (ECA), England and Wales.

2.2.3.The Electrical Contractors Association of Scotland (ECAS).

2.3. The plumbing installation must comply with the requirements of UK Water

Regulations/Bye-laws (Scotland), Building Regulations or any particular regulations and practices, specified by the local water company. The installation should be carried out by a plumber or contractor who is registered, or is a member of, an association such as:

2.3.1.Institute of Plumbing (IOP), throughout the UK.

2.3.2.National Association of Plumbing, Heating and Mechanical Services

Contractors (NAPH & MSC), England and Wales.

2.3.3.Scottish and Northern Ireland Plumbing Employers’ Federation (SNIPEF),

Scotland and Northern Ireland.

5

Pack Contents Checklist

9

Tick the appropriate boxes to familiarize yourself with the part names and to confirm that the parts are included.

1. Mira Play 9.5 kW

1 x Mira Play 9.5 kW

3 x Fixing Screws

3 x Wall Plugs

2. Documentation

1 x Installation and User Guide

1 x Installation Template

1 x Guarantee Card

6

3. Mira Response Adjustable Shower Fittings

2 x Slide Bar

End Caps

2 x Wall Plugs 1 x Handset

2 x Hose Seals

1 x Slide Bar

1 x Clamp Bracket

Assembly

1 x 1.25 m

Flexible Hose

1 x Soap Dish

1 x Hose Retaining Ring

2 x Slide Bar

End Supports 2 x Fixing Screws

Specifications

1. Plumbing

1.1. Minimum maintained inlet pressure:

9.5 kW = 70 kPa (0.7 bar)

1.2. Maximum static inlet pressure of 1000 kPa (10 bar).

1.3. Minimum static inlet pressure of 50 kPa (0.5 bar) to keep the inlet valve closed.

2. Electrical

2.1. The Mira Play 9.5 kW requires a 40 Amp fuse.

2.2. The terminal block will accept cable sizes up to 16 mm 2 .

3. Standards and Approvals

3.1. The Mira Play complies with all relevant directives for CE marking.

7

Installer Instructions

Read the section “Important Safety Information” first.

Plumbing Checklist

1.

Minimum maintained inlet pressure = 70 kPa (0.7 bar).

Maximum static inlet pressure = 1000 kPa (10 bar).

2.

Water treatment device (if required).

3.

Free flowing isolating valve.

4.

Positioned over water catchment area.

5.

Fitted to finished wall surface.

6.

No sharp hose kinks.

7.

Fittings positioned with greater than 25 mm gap or outlet double checkvalve fitted.

8.

Supply pipework flushed clear.

9.

Watertight inlet connection and fittings.

10. Cover secured correctly.

Minimum

200 mm from ceiling.

Convenient height for all the family.

Fixed to finished wall surface.

Isolating Valve

Avoid sharp kinks

Bath

Hose Retaining Ring

25 mm Min

Shower Tray

8

Plumbing (checklist in detail)

1.

The appliance is designed to operate with a minimum maintained inlet pressure of

70 kPa (0.7 bar), up to a maximum static inlet pressure of 1000 kPa (10 bar).

2.

When installed in very hard water areas (above 200 ppm temporary hardness) your installer may advise the installation of a water treatment device, to reduce the effects of limescale formation. Your local water company will be able to advise the hardness of water in your area.

3.

It is recommended that a non-restrictive (free flowing) isolating valve is fitted as part of the cold water supply pipe to allow the complete maintenance of the appliance. Do not use a valve with a loose washer plate (jumper) as this can lead to the build up of static pressure.

4.

The appliance is only suitable for installation within the shower area. It is fitted with a pressure relief device and must be positioned over a water catchment area with the controls at a convenient height for all users.

5.

The appliance must be fitted onto a finished flat and even wall surface (this wall surface should be tiled or suitably waterproofed). Do not fit the appliance to the wall and tile up to the case. For safety requirements, an air gap must be left behind the appliance.

6.

Avoid layouts where the shower hose will be sharply kinked. This may reduce the life of the hose.

7.

A Hose Retaining Ring is supplied to prevent the handset from dropping below the spillover level of the bath or shower tray, which could lead to contamination from backsiphoning. The supplied Hose Retaining Ring should meet the greater majority of user requirements for shower installations with flexible outlet fittings. However, there will be occasions where it will not provide a suitable solution. In these instances an outlet double checkvalve, e.g. a Mira DCV-H, must be fitted. This will increase the required supply pressure typically by 10 kPa (0.1 bar). See section “Accessories”.

8.

Supply pipework must be flushed to clear any debris before connecting to the appliance.

9.

To avoid damage to the case when soldered fittings are used, pre-solder the pipework and fittings before connecting them to the inlet connector assembly. Refrain from applying excessive force when making any connections. Always provide mechanical support when making the plumbing connections.

10. The appliance is fitted with a plastic inlet compression assembly for connecting to a

15mm supply pipe from the top, bottom or back. Double checkvalves, fitted in the inlet supply to the appliance, cause a pressure build-up, which could exceed the maximum static inlet pressure and damage the appliance.

9

Read the section “Important Safety Information” first.

Electrical Checklist

1.

Electrical supply fuse and consumer unit are adequate for the product.

2.

Shower unit is earthed.

3.

The minimum required supply cable size must conform to BS 7671.

4.

Double pole isolating switch.

5.

DO NOT twist live or neutral cable cores.

6.

Electrical connections are tightly secured.

DO NOT strain the terminal block.

7.

Plumbing supply completed before electricity supply is turned on.

Consumer Unit

Double pole Isolating

Switch

10

Electrical (checklist in detail)

1.

In a domestic installation, the rating of the electricity supplier’s fuse and the consumer unit must be adequate for the additional demand. All Mira Play electric showers are high power units, therefore it is essential to contact your electricity supplier to ensure that the supply is adequate for the product. Voltage drop due to local heavy demand will reduce the shower’s performance.

2.

The appliance must be earthed by connecting the supply cable’s earth conductor to the earth terminal.

Supplementary bonding: Within the bathroom or shower room, all accessible conductive parts of electrical equipment and extraneous conductive parts (metal parts) that are likely to introduce earth potential, must be electrically bonded to earth. If the cable is not mechanically protected, the cable size must be a minimum of 4.0 mm 2 (2.5 mm 2 if mechanically protected). Use a suitable earth bonding strap to connect the earth terminal to 15mm copper pipe. The installation must comply with the “REQUIREMENTS

FOR ELECTRICAL INSTALLATIONS” in accordance with BS 7671.

3.

Supply cable - see opposite.

Important! The shower circuit should be separated from other circuits by at least twice the diameter of the cable or conduit, and it should not be run through thermally insulating material or in locations where the ambient temperature is likely to exceed 30 °C. If any of these conditions are unavoidable, it is necessary to determine the cable size which will prevent damage to the cable caused by overheating.

4.

As a guide only, and in accordance with BS 7671 we recommend close circuit protection:

i.e. 9.5 kW = 40 Amp.

It is strongly recommended that a 30 mA Residual Current Device (RCD) is included in the electrical circuit. This may be part of the consumer unit or a separate unit. A separate, permanently connected supply is taken from the consumer unit to the appliance through a double pole isolating switch, which has at least 3 mm of contact separation.

The switch can be a ceiling mounted pullcord type within the shower room, or a wall mounted switch in an adjacent room.

5.

DO NOT twist the individual cable cores of either the live or neutral conductors, as this will prevent them from entering the terminal block.

6.

DO NOT exert strain on the terminal block. Ensure that the electrical connections are tightly screwed down.

7.

DO NOT turn on the electrical supply until the plumbing has been completed.

11

Installation

Mira Play

Read the section “Important Safety Information” first.

1.

2.

200 mm

3.

4.

Electrical supply is turned off at the mains.

5.

200 mm minimum gap from ceiling.

Remove three screws.

6.

7.

Remove Cover and determine supply pipe position.

INSTALLATION TEMPLATE

L N

Mira Sport

Attention Installer

For back inlet use soldered elbow.

8.

CAUTION! Do not drill into buried cables or pipes.

9.

Drill and plug* the three holes using template.

Fix appliance to wall.

* Alternative fixings for some wall structures are not supplied.

12

Flush a minimum of

10 litres through pipework.

10.

11.

12.

Connect supply pipe.

Do not overtighten!

L = BROWN

= GREEN

N = BLUE

Feed cable into Case. Fit Earth sleeve (not supplied) and strip insulation.

Do not twist cable cores.

13.

14.

Firmly connect the conductors. Do not exert strain on the terminal block.

15.

Make sure wires are clear of all mounting holes.

Refit the Service Tunnel and Cover. Make sure they fit correctly.

Do not overtighten screws.

13

Do not use alternative screws to secure the Cover. This can cause internal damage to the appliance.

Do not seal around the back of appliance.

Mira Response Adjustable Shower Fittings

Read the section “Important Safety Information” first.

1.

2.

Release

Button

Clamp Bracket

3.

Soap Dish/Hose

Retaining Ring

25 mm Minimum

Spill-over level

Position as shown to prevent back siphoning.

Slide Bar

Depress release button

FULLY and assemble Clamp

Bracket. Release the button when in desired position.

4.

Slide the Soap Dish and the

Hose Retaining Ring onto the

Slide Bar below the Clamp

Bracket.

Fit both the top and bottom

Supports. Make sure the slots are aligned to fit fully home.

14

5.

6.

Mark the positions of the slots on both top and bottom Supports.

7.

8.

CAUTION! Do not drill into buried cables or pipes.

First fix bottom Slide Bar Support and fully tighten the screw*. Then fix the top Slide Bar Support whilst pressing it down, to keep the whole assembly together.

Fit the End Caps to the Slide Bar

Supports.

9.

Fit the Hose to both the Handset and the

Shower Outlet, remembering to pass it through the Hose Retaining Ring. Do not overtighten the Hose connections.

* Alternative fixings for some wall structures are not supplied.

15

Commissioning

If you are unsure how an electric shower works, please read through the section

“User Instructions” before continuing.

1.

2.

3.

4.

Electrical supply is turned off at the mains.

5.

Set control to LOW.

6.

Turn water supply fully on.

Check for water leaks.

Turn control to full cold.

Switch on electrical supply.

7.

8.

9.

PUSH

Push START button.

COLD

0-5 secs

Water will be flowing at a cool temperature.

Turn control slowly.

Temperature remains cool and flow is reduced.

10.

Turn control to full cold.

11.

Set control to MEDIUM.

12.

+

5-10 secs

The temperature will rise slightly.

_

16

13.

15.

Set control to HIGH.

14.

+

_

The temperature will rise further.

16.

Adjust temperatures as required.

Flow rate will adjust automatically.

PUSH

Press STOP and isolate power.

17.

18.

The shower will purge water from its tank for a few seconds.

Residual water may drain over a few minutes.

Note! A slight “hissing” sound may be heard from the appliance during operation. High mains water pressure and high shower temperature will affect the tone. This is quite normal in use.

17

User Instructions

1. Warning!

1.1. DO NOT operate this appliance if it appears to be frozen. Allow the appliance to thaw and then contact your installer before using again.

1.2. DO NOT operate this appliance if water leaks from the pressure relief valve; maintenance will be required before the appliance can be safely used.

1.3. There are no user serviceable components beneath the cover of this appliance.

Only a competent tradesperson should remove the Cover.

1.4. If any of the following conditions occur, isolate the electricity and water supplies.

Contact your installer or refer to “To contact us”, on the back page of this guide.

1.4.1.If water is leaking from inside the product.

1.4.2.If the case is damaged.

1.4.3.If the appliance begins to make an odd noise, smell or smoke.

1.4.4.If the appliance shows signs of a distinct change in performance, indicating a need for maintenance.

1.4.5.If the cover is not correctly fitted.

2. Caution!

2.1. Read all of these instructions and retain this guide for later use.

2.2. Pass on this guide in the event of change of ownership of the installation site.

2.3. Anyone who may have difficulty understanding or operating the controls of any shower should be attended whilst showering. Particular consideration should be given to the young, the elderly, the infirm, or anyone inexperienced in the correct operation of the controls.

2.4. When this appliance has reached the end of its serviceable life, it should be disposed of in a safe manner, in accordance with current local authority recycling or waste disposal policy.

18

How Your Electric Shower Works

Hot water is produced by passing cold water through a heating tank.

COLD

+

_

The shower has three heater settings.

+

_

+

_

The warmer the shower, the lower the flow rate and vice versa.

19

The Effect of Seasonal Changes

+

_

* **

For a cold shower select Low.

For a summer warm shower select Medium.

For a winter warm shower select High.

During extremes of mains water supply temperature, adjust heater setting to obtain a better showering temperature.

The Effect of Other Water Devices

Example of how shower temperature stabilizes due to sudden pressure changes.

Selected

Showering

Temperature

+

_

Showering temperature will stabilize to within 6 o C band if other outlets are opened whilst showering, providing the minimum pressure does not fall below 70 kPa (0.7 bar).

Water inlet pressure fluctuations due to other draw offs (e.g. flushing toilet) will cause the showering temperature to increase.

20

Using Your Shower

Read the section “Important Safety Information” first.

1.

2.

Switch on electrical supply.

PUSH

Press START button.

3.

4.

+

_

5.

Set to desired position.

Check water temperature before entering shower.

+

6.

_

Allow 10-15 seconds for any temperature adjustments to reach the handset.

7.

PUSH

Press STOP button.

Shower will continue to run for a few seconds before stopping.

21

A small amount of water may continue to drain over a few minutes.

Changing the Spray Setting

The handset has three different spray settings (Start, Soothe and Force).

1.

2.

3.

Start

Turn the Spray Plate anticlockwise until it “clicks”.

Water will flow from the outer set of holes.

Soothe

Turn the Spray Plate anticlockwise until it “clicks”.

Water will flow from the large diameter holes.

Force

Turn the Spray Plate anticlockwise until it “clicks”.

Water will flow from the inner set of holes.

Adjusting the Clamp Bracket

1.

2.

Depress the release button and slide the Clamp Bracket assembly to the required position.

22

Move the Handset to the required angle.

Fault Diagnosis

The trouble shooting information table below gives details on probable causes and remedies should difficulties be encountered whilst the shower is in operation.

Warning! There are no user serviceable components beneath the cover of the appliance.

ONLY A COMPETENT TRADESPERSON SHOULD REMOVE THE FRONT COVER!

Symptom Power

Light

Heater

Setting

Low/

Medium/

High

ON High Shower is too hot during the summer.

Probable Cause Possible Remedy

The incoming water is warmer in the summer, so the shower heater setting is too high.

Turn the Heater

Control to Medium and adjust the

Temperature

Control until the desired temperature is achieved.

Shower is too hot.

ON

Turning the temperature control does not affect the water temperature.

ON

Medium/

High

Handset blocked.

Remove and clean.

Medium/

High

Handset blocked.

Remove and clean. If fault persists, contact the shower installer.

The water continues to flow when the double pole switch is turned off.

OFF Any

No water or very low flow rate.

OFF Any

The diaphragm is damaged.

Contact shower installer to replace the flow valve assembly.

The power is off at the double pole switch.

23

Switch on the power at the double pole switch.

(Continued...)

Symptom Power

Light

Heater

Setting

Low/

Medium/

High

Probable Cause

ON

ON

OFF

Any

Any

Any

Possible Remedy

The incoming water supply stop valves, or the appliance isolating valve, is closed.

Open the stop/isolating valve fully.

Handset blocked.

Remove and clean.

For sprayplate cleaning, refer to the

Handset manual.

The fuse is blown or the MCB/RCD has been tripped, indicating a possible electrical fault.

Renew the fuse or reset the MCB/RCD. If the fault persists, contact the shower installer.

No hot water from shower, with the controls in any position.

ON

ON

Medium/

High

Medium/

High

Other water outlets are being used during showering, causing the water pressure to drop below the minimum requirement.

The water pressure is below the minimum required.

Ensure the other water outlets, such as a washing machine or dishwasher, are not in use during showering.

Make sure that the incoming water supply isolating valve(s) are completely open. If the fault persists, contact the shower installer.

Shower temperature cycles between hot and cold.

ON Medium/

High

The temperature is set too high. This is causing the

Thermal Switch to turn off the Heating

Element to reduce the water temperature.

Turn the Temperature

Control anticlockwise to reduce the water temperature.

(Continued...)

24

Symptom Power

Light

Heater

Setting

Low/

Medium/

High

Probable Cause

ON

Possible Remedy

Medium/

High

The temperature is set too high. This is causing the

Thermal Switch to turn off the Heating

Element to reduce the water temperature.

Turn the Temperature

Control anticlockwise to reduce the water temperature.

DO NOT TAMPER with the Thermal Switch.

ALL OF THE FOLLOWING REMEDIES MUST ONLY BE PERFORMED

BY A COMPETENT TRADESPERSON!

ON

No hot water from the shower, with controls in any position.

ON

ON

ON

ON

Medium/

High

Medium/

High

Medium/

High

Medium/

High

Medium/

High

Insufficient mains water pressure.

Failure of the pressure switch, microswitch or thermal switch.

Internal wiring connection failed.

One of the Heater

Tank elements has failed.

Contact local water company.

Check the continuity of the switches, using a suitable continuity measuring device.

Replace the switches as necessary.

Check the integrity of the internal wiring.

Replace the Heater

Tank.

Switch assembly diaphragm fault.

Water dripping from the unit.

Replace switch assembly.

Turning the

Temperature

Control does not affect the water temperature.

ON

ON

Medium/

High

Medium/

High

The Flow Regulator is faulty.

The Handset is blocked.

Replace the Flow

Regulator.

Remove and clean. If fault persists, contact

Customer Services.

25

Symptom Power

Light

Heater

Setting

Low/

Medium/

High

Probable Cause

No water, or very low flow rate.

ON

ON

ON

ON

ON

ON

OFF

OFF

Any

Any

Any

Any

Any

Any

Any

Any

Possible Remedy

Handset blocked.

The incoming water supply stop valves, or the appliance isolating valve, is closed.

Insufficient mains water pressure.

Remove and clean.

Open the stop/isolating valve fully.

Check the integrity of the internal wiring.

The Heater Tank is excessively scaled.

Replace the Heater

Tank.

The Pilot Valve is faulty.

Replace.

Inlet Filter blocked.

Clean or renew. See

“Maintenance” section.

The power is off at the double pole switch.

Switch on the power at the double pole switch.

The fuse is blown or the MCB/RCD has been tripped, indicating a possible electrical fault. For example,

Heater Tank element failure.

Renew the fuse or reset the MCB/RCD.

Replace the Heater

Tank.

Water leaks from the bottom of the case near the outlet.

There is no flow from the outlet.

ON Any The Pressure Relief

Valve in the Heater

Tank has been triggered (this works to reduce the damage to the appliance if the outlet is blocked or the unit is frozen.

Resolve the blocked outlet.

(Continued...)

26

Symptom Power

Light

Heater

Setting

Low/

Medium/

High

Probable Cause Possible Remedy

When the Relief

Valve operates, a small rubber ball is ejected.

Reset the Relief Valve assembly. See

“Maintenance” section.

The water cannot be turned off.

OFF

OFF

OFF

Any

Any

Any

The Pilot Valve is faulty.

The diaphragm is damaged.

The supply pressure is below the minimum requirement.

Replace.

Replace the Flow Valve assembly.

Contact local water company.

Check the static water pressure. Note that the static pressure may fall below minimum requirement when other appliances are drawing water. For example, a washing machine or garden hose.

27

Maintenance

Handset - Cleaning

Clean with mild washing up detergent or soap solution.

Wipe dry with soft cloth.

CLEAR

Poor shower performance can be avoided by cleaning the spray head. Use thumb or soft cloth to wipe rubber nozzles. The handset must also be descaled regularly.

Inlet Filter - Cleaning/Renewing

Read the section “Important Safety Information” first.

1.

2.

3.

Electrical supply is turned off at the mains.

Turn water supply fully off.

Remove three screws,

Cover and Service

Tunnel.

4.

5.

Hold a wrench across the flats of the plastic connector. Unscrew the Filter using another wrench as shown. Clean or renew the Filter as necessary.

Refit in reverse order, making sure the Filter is screwed fully home.

Do not overtighten. Make sure plumbing connections are sealed before restoring electricity supply.

28

Relief Valve Assembly - Resetting

Read the section “Important Safety Information” first.

1.

2.

3.

4.

Electrical supply is turned off at the mains.

Turn water supply fully off.

Switch Assembly

Remove three screws,

Cover and Service

Tunnel. Small rubber ball should be loose in the Case.

Screws

Heater

Tank

5.

Flow Regulator

Assembly

Ball

Remove the five screws and lift out the Switch, Heater Tank and Flow Regulator assemblies.

6.

Ball

Using your finger, push the ball back into the hole in the Heater Tank assembly. DO NOT remove the ‘O’ seal.

Refit the components in reverse order and replace the Cover. If the Cover does not fit easily, rotate the controls slightly so that they fit onto the Sindles beneath. DO NOT force the Cover to fit.

29

600 mm

Dimensions

225 mm 98 mm

335 mm

332 mm

52 mm

30

Wiring Diagram

31

Accessories

DCV-H: An outlet double checkvalve, designed to prevent the backflow or backsiphoning of potentially contaminated water, through shower controls which are fitted with a flexible hose as part of the outlet shower fitting. Available as an optional accessory from all Mira

Showers stockists.

Spare Parts

Mira Play Spare Parts List (see diagram on next page)

406.27

439.75

439.76

439.88

439.89

439.90

439.93

439.99

Inlet filter (with ‘O’ Seal fitted)

Inlet Connector Assembly

Clamp Bracket - components identified “A”

Seal Pack - components identified “B”

Screw Pack - components identified “C”

Thermal Switch

Heater Tank 9.5 kW

Outlet Connector and Ball

1539.339

Switch Assembly

1539.340

Neon Assembly (not shown)

1539.341

Cover Assembly - White/White Panel

1539.342

Cover Assembly - Satin/Chrome Panel

1539.343

Service Tunnel - White

1539.344

Service Tunnel - Satin

1539.349

Terminal Block Assembly

1539.350

Flow Regulator Assembly

1539.352

Start/Stop Switch Assembly

1539.355

Cover Assembly - White/Chrome Panel

32

Mira Play Spare Parts Diagram

C

1539.349

1539.339

1539.343

1539.344

406.27

439.75

A

C

B

C

A

B

C

1539.352

1539.350

C

B

C

439.99

B

C

439.90

439.93

4 mm MINIMUM

1539.341

1539.342

1539.355

Important Note!

Push-fit connectors must be assembled back to back onto terminals of micro-switches.

A minimum air gap of 4 mm must be maintained between the connectors after assembly.

33

Mira Response Adjustable Shower Fittings Spares List

150.58

411.05

411.23

411.30

411.37

411.53

411.58

411.91

411.92

411.94

411.96

632.73

Hose - chrome

Adjuster Ring

Clamp Bracket Assembly

Slide Bar Support Assembly

Service Pack 'O' Seals - components identified 'A'

Slide Bar - stainless steel

Hose Retaining Ring

Soap Dish Pack

Adjustable Handset

Screw Pack

Spray Plate Assembly - Low capacity

Hose Washer

34

Mira Response Adjustable Shower Fittings Spare Parts Diagram

411.94

411.53

411.30

411.96

411.92

411 94

A

632.73

411.05

411.23

411.91

632.73

150.58

411.58

411.94

411.94

411.30

35

Customer Service

1058045-W2-B 36

UKAS

© Kohler Mira Limited, May 2005

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement