User Instructions. Mira Play
Add to my manuals
36 Pages
Mira Play is a 9.5 kW electric shower with separate controls for power selection and temperature adjustment. It features a flow regulator that stabilizes temperature changes caused by water pressure fluctuations. The shower comes complete with adjustable shower fittings, including a handset with three spray actions and a slide bar for easy height adjustment. Its compact design makes it suitable for small to medium-sized bathrooms. The Mira Play is easy to install and maintain, with a range of safety features for peace of mind, including overheat protection and an automatic shut-off function.
advertisement
User Instructions
1. Warning!
1.1. DO NOT operate this appliance if it appears to be frozen. Allow the appliance to thaw and then contact your installer before using again.
1.2. DO NOT operate this appliance if water leaks from the pressure relief valve; maintenance will be required before the appliance can be safely used.
1.3. There are no user serviceable components beneath the cover of this appliance.
Only a competent tradesperson should remove the Cover.
1.4. If any of the following conditions occur, isolate the electricity and water supplies.
Contact your installer or refer to “To contact us”, on the back page of this guide.
1.4.1.If water is leaking from inside the product.
1.4.2.If the case is damaged.
1.4.3.If the appliance begins to make an odd noise, smell or smoke.
1.4.4.If the appliance shows signs of a distinct change in performance, indicating a need for maintenance.
1.4.5.If the cover is not correctly fitted.
2. Caution!
2.1. Read all of these instructions and retain this guide for later use.
2.2. Pass on this guide in the event of change of ownership of the installation site.
2.3. Anyone who may have difficulty understanding or operating the controls of any shower should be attended whilst showering. Particular consideration should be given to the young, the elderly, the infirm, or anyone inexperienced in the correct operation of the controls.
2.4. When this appliance has reached the end of its serviceable life, it should be disposed of in a safe manner, in accordance with current local authority recycling or waste disposal policy.
18
How Your Electric Shower Works
Hot water is produced by passing cold water through a heating tank.
COLD
+
_
The shower has three heater settings.
+
_
+
_
The warmer the shower, the lower the flow rate and vice versa.
19
The Effect of Seasonal Changes
+
_
* **
For a cold shower select Low.
For a summer warm shower select Medium.
For a winter warm shower select High.
During extremes of mains water supply temperature, adjust heater setting to obtain a better showering temperature.
The Effect of Other Water Devices
Example of how shower temperature stabilizes due to sudden pressure changes.
Selected
Showering
Temperature
+
_
Showering temperature will stabilize to within 6 o C band if other outlets are opened whilst showering, providing the minimum pressure does not fall below 70 kPa (0.7 bar).
Water inlet pressure fluctuations due to other draw offs (e.g. flushing toilet) will cause the showering temperature to increase.
20
Using Your Shower
Read the section “Important Safety Information” first.
1.
2.
Switch on electrical supply.
PUSH
Press START button.
3.
4.
+
_
5.
Set to desired position.
Check water temperature before entering shower.
+
6.
_
Allow 10-15 seconds for any temperature adjustments to reach the handset.
7.
PUSH
Press STOP button.
Shower will continue to run for a few seconds before stopping.
21
A small amount of water may continue to drain over a few minutes.
Changing the Spray Setting
The handset has three different spray settings (Start, Soothe and Force).
1.
2.
3.
Start
Turn the Spray Plate anticlockwise until it “clicks”.
Water will flow from the outer set of holes.
Soothe
Turn the Spray Plate anticlockwise until it “clicks”.
Water will flow from the large diameter holes.
Force
Turn the Spray Plate anticlockwise until it “clicks”.
Water will flow from the inner set of holes.
Adjusting the Clamp Bracket
1.
2.
Depress the release button and slide the Clamp Bracket assembly to the required position.
22
Move the Handset to the required angle.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement