Samsung SMARTCAM User manual

1. Smart phone requirements
Hardware / Operating System
SmartCam
Android
English
3. Tap <Start>.
Requirements
OS
- Android 2.3.3/4.0/4.1/4.2/4.3
CPU
- 1GHz or higher
RAM
- 128MB or more (recommended),
RAM : 50MB (Minimum)
Network
Video Codec
Recommended Smart Phones
Welcome to
- Wi-Fi or 3G/LTE wireless communicationenabled smart phone
Setup using 3 simple steps below.
Step 1. Sign up for an account
Step 2. Register your camera
- H.264
Step 3. Configure your camera
- Galaxy S3/S4
Start
Recommended Tablet PC
J

- Galaxy Note 10.1
If you use 3G or 4G(LTE) data communication, excessive amount of
fees can be billed and may cause data delays or loss. Wi-Fi is
recommended.
4. Enter requested information.
Create new account
ID
M

Email address is used to find the
account password.
8~14 alpha numeric characters
PW
8~14 alpha numeric characters
5. Check “Agree to the terms and
conditions”, and tap <Register>.
With SmartCam app, you can monitor what matters to you
directly from your smart phone.
Download the application from the Play Store and install it on
your smart phone.
Confirm Password
Name
Enter the user name.
e-Mail
2. Subscription
ex) [email protected]
I agree to the Samsung Techwin's terms and
conditions.
1. Run the downloaded application.
Terms of Services
Privacy Policy
™ Search keywords for the application: “Samsung SmartCam”,
“Smartcam”, “Samsung techwin”, “Techwin”.
Register
6. Tap <Next> when the menu on
the completion of a new member
registration pops up.
2. Tap <Create new account>.
Account
created. Tap <Next> to
.
setup the camera.
Cancel
Next
) [email protected]
|Enter User ID.
M
Enter Password.
Remember me
Auto Login

Tap <Add Camera> after logging
in if you are already a member.
Camera
Login
Forgot your ID?
Forgot your password?
Create new account
Setup
Add Camera
About
9. After selecting a camera to
connect, tap <Next>.
Wi-Fi Direct connection
M


You can only use it in a camera that has a Wi-Fi Direct sticker
attached to it.
M

Registration
Select a camera that has the last four digits of
the serial number displayed on the back of the
product.
Select a camera that has the last
four digits of the serial number on
the back of the product.
(Ex: smartcam_xxxx or DIRECTxxxx)
Press the button, "Is this camera already in use?" when you
register a camera being used in another account, in order to register
it immediately without setting it.
11. The LED of the camera will
turn into green if a camera is
connected to Wi-Fi.
Tap <Next>.
Registration
The camera LED color will change from
blue to green within 2 minutes. Tap <Next>
when it turns green.
7. Tap <Wireless Setup>.
DIR
iFi E
Next
CT
W
Is there a WiFi DIRECT sticker on
the camera lens?
10. Select a wireless hub connected
to your camera.
If yes, select Wireless Setup.
If not, select Wired Setup.
Wireless
Setup
Wired Setup
Is this camera already in use?
8. Tap <Next> after connecting
a camera according to the
instructions displayed on the
screen.
Registration
1
DCIN
CIN 5V
Connect the power adapter.
Camera will take about 2
minutes to boot-up.
REST
2
REST
When the LED flashes in red,
press the Wi-Fi button for 5
seconds.
3
The status LED will change to
light yellow. Tap next.
Next
SSW
: After entering the
password, connect to a
wireless hub.
: Without the password,
you will not be connected to
a wireless hub.
- Other Wi-Fi Networks (not
listed) : Enter the SSID name
and password to connect to
the network.
If selected, it shows guide
on SSID and networking
procedures.
- Network password :
If you select a wireless hub
with the password, then the
pop up window will prompt
you to enter the password.
Click <Show Password> to
check your password.
Next
12. Enter <Camera Name> and
<Camera password> and then
click <OK>.
Registration
Select the wireless network you
want the camera to connect to.
Apple Network 8dfdc7
M
design

Click <Show Password> to check
your password.
Registration
The camera LED color will change from
blue to g
green within 2 minutes. Tap
p <Next>
when
it turns
Create
a name
forgreen.
the camera and camera
password fo security.
Camera Name
ex: Living Room
Cisco_WPS_57090
Camera password
KT12580
1-8 alpha numeric characters
NETGEAR27
Confirm camera password
Show Password
Cancel
Next
Other Wi-Fi Networks (not listed)
13. The camera registration is
completed.
Select <Yes>
for a camera setting.
Select <No> to view a live
screen.
Registration
Select the wireless network you
want the camera to connect to.
Network password
Apple
Network
8dfdc7
Enter
the password
for the hub.
design
Show Password
Cisco_WPS_57090
Cancel
OK
OK
Camera registered
successfully.
The camera settings can be set
to your preference. Continue
with the camera setup?
KT12580
NETGEAR27
1 2 3 4 5 6 7 8 9 0
q w e
r
a s d
t
f
y u
g h
i
j
o p
k
l
No
z x c v b n m
123
Sym
···
?
English(US)
···
.
Done
Yes
3. Camera List
10. If the camera is not detected,
please enter the camera serial
number manually.
Cable connection
7. Tap <Wired Setup>.
M

For camera’s serial number
location, refer to [
].
No matching camera is found.
Check the serial number and enter it down below.
1. Move to the <Camera> item.
From the listed active cameras,
] on
tap the desired camera’s [
the right.
Serial number
Camera
Prev
M
Next

1 2 3 4 5 6 7 8 9 0
q w e
If yes, select Wireless Setup.
If not, select Wired Setup.
r
a s d
t
y u
f
g h
i
j
Setup
About
Add Camera
test
|Enter the 15-digit serial number.
DIR
iFi E
CT
W
Is there a WiFi DIRECT sticker on
the camera lens?
Camera Move
Registration
test2
You cannot monitor an inactive
camera.
o p
k
l
z x c v b n m
Wireless
Setup
Is this camera already in use?
8. Tap <Next> after connecting
a camera according to the
instructions displayed on the
screen.
Registration
1
DCIN 5V
?
English(US)
···
.
Sym
11. Enter <Camera Name> and
<Camera password> and then
click <OK>.
Installation & Registration Guide
Once setup is completed, you will no longer need the
network cable.
···
123
Wired Setup
M

Registration
Found Smartcams.
Select the camera listed below and tap <Next>. If the
cameras are not listed, enter the camera serial
number manually.
Create a C8BG6V2C801011T
name for the camera and camera
password for security.
Click <Show Password> to check
your password.
CameraC8AT6V2C400079A
Name
2. Live, Event, Playback and Setup
icons will be displayed.
J
ex: Living Room
KHNL6V2D70002KN
Connect the power adapter. Camera will
take about 2 minutes to boot-up.
Done
Camera password

test
Different functions are supported by
each model.
1-8 alpha numeric characters
2
Confirm camera password
Connect the camera to
the wireless router using
network cable.
Show Password
Cancel
Serial number
3
Tap <Next> when the camera LED
changes to green.
(For *SNH-1010N, the power LED turns to
white)
OK
test
|Enter the 15-digit serial number.
Prev
Next
Live
Prev
9. Select the camera found and tap
<Next>.
M

When your smartphone is
connected to the same Wi-Fi
network as the camera, it will
automatically search for the
camera.
Next
Registration
Found Smartcams.
Select the camera listed below and tap <Next>. If the
cameras are not listed, enter the camera serial
number manually.
C8BG6V2C801011T
C8AT6V2C400079A
12. The camera registration is
completed.
Select <Yes> for a camera
setting.
Select <No> to view a live
screen.
Playback
Setup
Delete Camera
Camera registered
successfully.
The camera settings can be set
to your preference. Continue
with the camera setup?
KHNL6V2D70002KN
Event
1. To delete an added camera, tap
and hold the desired one from the
camera list, and tap <Delete>.
Camera
Setup
About
Add Camera
test
Are you sure you want to remove this
camera?
Cancel
No
Serial number
|Enter the 15-digit serial number.
Prev
Next
Yes
Delete
4. Live Video
1. Tap the desired camera’s [
tap the <Live> icon.
Live Video
] or
Camera
Setup
No.
Add Camera
M

If there is the latest version of
firmware, when you make a live
video connection, a pop up will
appear so that you can update your
camera’s firmware.
Description
About
test
test
test
A user can record audio and play the recorded audio
through the camera speaker.
Audio playing
test2
test
IR Lighting
Live
2. Enter the <Camera password>
for the camera selected. This is
the same camera password you
created at the time you registered
the camera.
Check the <Save> option to save
the camera password.
Within 20 seconds, it will start
streaming.
Event
Playback
b
No.
J

Different functions are supported depending on the model.
Save
Cancel
t
f
y u
g h
i
Sym
···
Information
Current audio/video information is displayed.
b
Manual
Recording
A user can manually save the video in the SD card.
 If there is storage space of 10% while the SD card
overwrite function is not activated, you cannot perform
manual recording.
 SNH-P6410BN supported
j
c
Capture
You can capture and save a still image from the video.
Two-way
Audio
The mic will be activated for bidirectional audio between
your camera and a smart phone.
 Refer to the bidirectional audio function.
HQ

Melody
The selected melody will be heard through the camera
speaker.
 SNH-P6410BN supported
Brightness
control
Adjusts the screen brightness.
Flip control
Flips the video image.
o p
k
l
z x c v b n m
123
OK
1 2 3 4 5 6 7 8 9 0
r
?
English(US)
Description
test
|Enter the camera password.
a s d

SNH-1010N supported
Two-way Audio
Camera password
q w e
M
c
You can record a max of 10 audio files.
SNH-P6410BN supported
If you select <Night Vision> in general settings, IR lighting
will operate for two minutes.

Setup
test


···
.
According to the network service provider’s policy, or the network
connection status, it may take a while to load.
Enables high quality video.
Depending on the network service provider’s policy or
network conditions, video and audio may not be
smoothly played.
It detects motion within the area set by the user.
Motion zone


Refer to the motion zone functions.
SNH-P6410BN supported
1. Tap on the Two-way Audio icon.
2. The Mic icon will appear.
3. Talk while pressing down the mic icon. Voice will be
recorded from the camera mic. After finishing talking, press
down the icon for two seconds so that the audio information
will be transmitted through the network.
4. Even if you did not activate the two-way audio function,
you can receive the audio sound of the video. In addition,
the microphone setting should be at least 1 or higher if you
want to use the two-way audio function.
J


When there are multiple users logged on to the camera, first person
who tap the Talk icon will have the control.
While the bidirectional audio is on, you need to tap the bidirectional
audio icon again to cancel the function.
Condition
Audio Support
Wi-Fi
3G/LTE
Relay Mode
Support (it is not supported if the
bidirectional audio icon is inactive)
Support
Motion zone
Cancel
Reset
OK
Relay mode
General setting
If the router where your camera is connected to does not have
the UPnP function or if the camera is connected to a dual router,
your mobile device will be connected to the 3G or LTE network
in a relay mode and you will see the video for the first seven
] in your live
minutes only. In relay mode, you can check [
video. When setting your device to a Wi-Fi network,you can
make a connection in general mode.
1. Tap <General>.
J

1. Tap the motion zone icon.
2. Connect to the motion zone mode.
3. After touching the video, drag it to set the area.

You can set a max of three motion zones.



4. If you want to run the motion zone in the area set, tap
<OK>.

Motion is detected only in the set area.

5. To delete the set area, press <Reset> and <OK>.
If you want to exit the motion zone setting mode, tap
<Cancel>.
To control digital zooming
The relay mode is used to transmit the camera video to a user’s
device through the samsung server even if the network condition is
not optimal.
The audio is useable in relay mode but if the bidirectional icon is set
to deactivation due to network problems, the audio is not available.
The HQ mode live screen is not available in relay mode.
If the router’s UPnP is not set, then you might be connected in relay
mode. The settings may differ depending on the connected
Broadband Router model. For more information, refer to the user
manual of the applicable router.
If you have trouble connection to the camera, visit "http://www.
samsungsmartcam.com", go to support page, and refer to
"Troubleshooting" on it.
Camera Name
2. Configure the basic camera
settings.
• Speaker/Mic : Adjust the
volume for the camera’s built-in
mic or speaker.
• Voice REC : You can record
or delete the voice from the
camera's live video.

SNH-P6410BN supported
Voice REC
Night Vision
WDR
Display date
Save Camera password
Change Camera password
status LED
Firmware Version
v1.00
Cancel
Apply
Voice List
01. No Voice
• Night Vision : Set the IR lighting.
Check <Night Vision> to set
the camera to switch to the
night vision mode automatically.
M

5. Camera Setup
test
test
Speaker
Mic
• Camera Name : Camera name
is used to easily identify the
camera when you have more
than one.
Tap the <Setup> icon to configure a camera to be monitored.
You can also zoom in by pinch open using two
fingers on the screen. To zoom out, pinch close
on the screen.
Touch and hold to drag the screen in any
direction to reveal the hidden part of the image
if enlarged bigger than the screen.
General
Setup
In the case of SNH-1010N, you can
check <Night Vision> for a
camera to automatically operate the
IR lighting for two minutes
depending on the brightness of the
neighboring areas.
• WDR : You can compensate for
the backlight by making a dark
area brighter, and a bright area
darker.

SNH-P6410BN supported
02. No Voice
03. No Voice
04. No Voice
05. No Voice
06. No Voice
07. No Voice
08. No Voice
09. No Voice
10. No Voice
General
Camera Name
test
Speaker
Mic
M
M

test
Current digital zooming level is noted next to the digital zoom box,
and digital zooming supports zooming up to x4.
General
Network
test1
• Display date : Displays the date/
time on the live video.

Current Password
Voice REC
V
Night
N
NewVision
Password
SNH-P6410BN supported
1-8 alpha numeric characters
W
WDR
Time
Event
Live
Event
Playback
Setup
SD Card
• Save Camera password :
You will be connected to your
camera without having to enter
the password.
Confirm Password
date
D
Display
Show Password
Save Camera password
S
Cancel
Apply
Change Camera password
C
status LED
• Change Camera password :
Change the current camera
password.
Firmware Version
Cancel
v1.00
Apply
• status LED : You can turn on or off the LED on your camera.

SNH-P6410BN supported
1. Tap the <Event>.
• Firmware Version : You can check the current version and
the latest distributed version and even make updates.
If there is the latest version of firmware, when you make a live
video connection, a pop up will appear so that you can update
your camera’s firmware.
3. Tap <Apply>.
J

Network setting
Network
2. Set your event items.

If the Wi-Fi receiving sensitivity is
poor, receiving a video may not
work properly. Move the location of
the camera to adjust receiving
sensitivity.
• Event alert : You will be alerted
when motions/audio is detected
and video is saved in Youtube
or Picasa.
Apple Network 8dfdc7
J
Cisco_WPS_57090
For model SNH-P6410BN, video is
saved in the SD card, not Youtube.

If you want to send notifications to
YouTube/Picasa at the time of
occurring an event, register Google
account first.
3. Tap <Apply>.
Time
2014-01-20 02:04:38
Time zone
|
(GMT) Greenwich Mean Time
Sensitivity
Google account setting
YouTube
Picasa
test
General
Network
Cancel
Apply
Event
Event
Event alert
SD Card
You can send videos and images to YouTube or
Picasa via your Google account.
S
Sensitivity
2. Set the SD card item.
Google e-Mail
• Use SD card : When you set
motion/audio, the video will be
automatically saved in the SD
card.
Audio Detection
A
Sensitivity
S
Google Password
Google account setting
G
Show Password
YouTube
Y
Need to create a
Google account.
Picasa
P
Cancel
Cancel
Move
OK
Apply
• Continuous Recording : Video
is saved regardless of the event
that occurs.
SD Card
Use SD card
Continuous Recording
If you activate use of an SD card, the events will
be automatically saved.
SD card Overwrite
Status
Format
Size (Free/Total) : 3.18 / 3.66 GB
• SD card Overwrite : If the SD
card capacity is insufficient,
then it will automatically start
overwriting the oldest data.
• Status : Check the remaining
capacity of the SD card.
Cancel
• Format : Delete all the data in the SD card.
Daylight Saving Time
3. Tap <Apply>.
Cancel
Setup
Audio Detection
Motion Detection
• Picasa : Sends event images to
the user’s Picasa account.
NETGEAR27
Time
• Daylight Saving Time : Check
this option if you live in a country
or region where DST(Daylight
Saving Time) is applied.
You need to purchase an SD card if you want to use it.
1. Tap <SD Card>.
Sensitivity
|
Time setting
• Time zone : Select your region.

KT12580
Other Wi-Fi Networks (not listed)
2. Set the camera’s clock.
Applicable to SNH-P6410BN only.
Time
• YouTube : Creates 30 seconds
long footage and uploads onto
the user’s YouTube account.
Select a wireless network and enter the
password.
M
1. Tap <Time>.


Motion Detection
design
M
J
Event
Wi-Fi
2. Configure the wireless network.
• Wi-Fi : Display the list of wireless
hubs that you can use.
SD card setting
Event alert
• Motion/Audio Detection :
Specify whether to trigger the
alarm or not, and specify the
sensitivity.
The higher the sensitivity is, the
subtler motion/audio events will
be detected.
Different functions are supported depending on the model.
1. Tap the <Network>.
Event setting
Apply
Apply
6. Event List
1. Tap on the <Event> icon to see
the YouTube and Picasa event
links.
M

2. Detected events will be saved in the server and displayed in
the event list.
test
YouTube icon:
Tap on the YouTube
icon to play the YouTube
video.
Only when you set YouTube/Picassa
after registering a Google account,
it will be displayed in the event list.
Deleting Each Event
1. Tap and hold the desired event to
be deleted.
Event
Jan-20-2014
14:26:23
Jan-20-2014
14:25:30
Jan-20-2014
14:24:20
Event
Audio
Detection icon
Jan-20-2014
Jan-20-2014
Picasa icon:
Tap on the Picasa icon
to see picture.
14:26:23
Jan-20-2014
14:25:30
Jan-20-2014
Motion Detection
Icon
test
14:22:18
Jan-20-2014
14:21:18
Jan-20-2014
14:19:24
14:24:20
Jan-20-2014
Jan-20-2014
14:18:17
14:22:18
Jan-20-2014
Jan-20-2014
Live
Event
Playback
14:17:35
14:21:18
Setup
Jan-20-2014
Jan-20-2014
14:16:16
14:19:24
Jan-20-2014
14:15:56
Jan-20-2014
M


You will get a notification prompt
when event is detected by the
camera.
14:18:17
test
Jan-20-2014
14:17:35
2. Tap on <OK> to delete the event.
Jan-20-2014
14:16:16
Jan-20-2014
Jan-20-2014
14:15:56
While you are uploading a video to
YouTube or Picasa, events are not
detected.
Event
14:26:23
Jan-20-2014
14:25:30
Jan-20-2014
14:24:20
Motion Detection
M
- test Jan-20-2014 02:05:59
Live

Event
test
Live
Event
Pl
Playback
ayback

Setup
Jan-20-2014
For model SNH-P6410BN, video is saved in the SD card, not
Youtube. You can play it in the SD playing menu.
Phone does not allow you to play the private videos automatically.
To see the event videos on your phone, tap on the YouTube app and
sign into your account(same YouTube account used for the Camera).
While logged in to the YouTube, tap the YouTube icon to play the video
automatically.
14:22:18
Delete
alert?
Jan-20-2014
14:21:18
Jan-20-2014
Cancel
14:19:24
Jan-20-2014
14:18:17
Jan-20-2014
14:17:35
Jan-20-2014
14:16:16
Jan-20-2014
14:15:56
Deleting All Events
1. Tap the menu button to display
<Delete All> popup.
Event
Jan-20-2014
14:26:23
Jan-20-2014
2. Tap on the <Delete All> to clear
the event list.
14:25:30
Jan-20-2014
14:24:20
Jan-20-2014
14:22:18
Jan-20-2014
14:21:18
Jan-20-2014
14:19:24
Jan-20-2014
14:18:17
Jan-20-2014
14:17:35
Jan-20-2014
14:16:16
Jan-20-2014
Delete All
14:15:56
OK
7. SD playing
9. Alarm setting
SD Save
J




Continuous recording automatically saves video to SD memory every
five minutes.
Manual recording is started by pressing the manual recording button
in the live video. If you close the app without releasing the button, an
additional 30 seconds of video will be saved before termination.
Event recording saves motion or audio for thirty seconds and if
motion or audio is detected again in the meantime, the amount of
saving time is extended.
In the case of manual or event recording while continuous recording
is ongoing, video play time can vary depending on the interval of
continuous recording (five minutes).
1. Tap the <Playback> icon.
J

5. On the screen, a circular shaped
timeline (24 hours) will be
displayed. The time zone with
the search data is classified by
colors.
2014.01.01
Applicable to SNH-P6410BN only.
Camera
►
09:04:57
2. Set the alarm for an event.
• Sounds/Vibrate/Non-sounds :
When an event occurs, an alarm
will be displayed as it was set.
Setup
About
Auto Login
Setting Alert
Sounds
Vibrate
6. Check the timeline and drag it to
the desired playing time [
] to
set the video playing start time or
enter the time on your own.
• Alert Message Pop-up : When
an event occurs, a notification
pop up will appear.
Non-sounds
Alert Message Pop-up
Screen off mode Pop-up
• Previous/Next video : Move to
the time where the video exists.
Previous video
7. Tap the < ► > button.
Play the video data.
test
1. Move to the <Setup> item.
Playback
Next video
• Screen off mode Pop-up : When
an event occurs with the screen
turned off, a notification pop up
will appear.
test
10. Info.
Checking the S/W info
1. Move to the <About> item.
8. Auto Login Setup
test
Camera
2. You can check the information of
the currently installed software.
1. Move to the <Setup> item.
Camera
Live
2. Searchable dates are displayed
on the calendar.
Tap the left/right < ,
>
button to select between year/
month in the top of the calendar
to move to the previous or next
month.
3. Select the desired date of search.
Event
Playback
Playback
You can select a saved video type in
the playing list.
About
Created Date
v2.01
2013. 12. 26
About
Copyright
Auto Login
Samsung Techwin
This software uses FFmpeg under LGPL v2.1
Setting Alert
Help Guide
Sounds
Vibrate
January 2014
Sun
Mon
Tue
Non-sounds
Wed
Thu
Fri
Sat
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
1
Alert Message Pop-up
Screen off mode Pop-up
Help guides
1. Move to the <About> item.
4. Select an event type that you
want to search.

2. If you check <Auto Login> and
run the app when it is terminated,
you will be automatically logged
in.
Setup
Setup
Setup
Version
2. Tap the <Help Guide> menu to see help.
Type
Motion Detection
M

The language set in your UE will be automatically detected and the
help menu will be provided in that language. Help is available in
seven different languages.