Sharp FO-1530 Service manual

UX-510UA
FO-1470U
SERVICE MANUAL
No. 00ZUX510UASME
FACSIMILE
UX-510A
MODEL FO-1470
SELECTION CODE
U
Illustration: UX-510UA
open
DESTINATION
U.S.A.
LCR
www.OpenLCR.com
CONTENTS
CHAPTER 1. GENERAL DESCRIPTION
[1] Specifications ............................................
[2] Operation panel .........................................
[3] Transmittable documents ..........................
[4] Installation .................................................
[5] Quick reference guide ...............................
1-1
1-2
1-3
1-4
1-9
CHAPTER 2. ADJUSTMENTS
[1] Adjustments .............................................. 2-1
[2] Diagnostics and service soft switch .......... 2-2
[3] Troubleshooting ...................................... 2-19
[4] Error code table ....................................... 2-20
CHAPTER 3. MECHANISM BLOCKS
[1] General description ................................... 3-1
[2] Disassembly and assembly
procedures ....................................... 3-4
CHAPTER 4. DIAGRAMS
[1] Block diagram ............................................4-1
[2] Wiring diagram .......................................... 4-2
[3] Point-to-point diagram ............................... 4-3
CHAPTER 5. CIRCUIT DESCRIPTION
[1] Circuit description ..................................... 5-1
[2] Circuit description of control PWB ............ 5-2
[3] Circuit description of TEL/LIU PWB .......... 5-8
[4] Circuit description of
power supply PWB ............................5-11
[5] Circuit description of CCD PWB .............. 5-11
CHAPTER 6. CIRCUIT SCHEMATICS AND
PARTS LAYOUT
[1] Control PWB circuit ................................... 6-1
[2] TEL/LIU PWB circuit .................................. 6-9
[3] Power supply PWB circuit ...................... 6-13
[4] CCD PWB circuit ..................................... 6-15
[5] Operation panel PWB circuit ................... 6-16
CHAPTER 7. OPERATION FLOWCHART
[1] Protocol ..................................................... 7-1
[2] Power on sequence ................................... 7-2
CHAPTER 8. OTHERS
[1] Service tools ............................................. 8-1
[2] IC signal name .......................................... 8-4
[3] Changing the record paper size ................ 8-6
PARTS GUIDE
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for
maintaining the safety and performance of the set.
SHARP CORPORATION
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
UX-510UA
FO-1470U
CAUTION FOR BATTERY REPLACEMENT
(Danish)
ADVARSEL !
Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandoren.
(English)
Caution !
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the equipment manufacturer.
Discard used batteries according to manufacturer’s
instructions.
(Finnish)
VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu.
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan
tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden
mukaisesti.
(French)
ATTENTION
Il y a danger d’explosion s’ il y a remplacement incorrect
de la batterie. Remplacer uniquement avec une batterie du
même type ou d’un type recommandé par le constructeur.
Mettre au rébut les batteries usagées conformément aux
instructions du fabricant.
(Swedish)
VARNING
Explosionsfare vid felaktigt batteribyte.
Använd samma batterityp eller en ekvivalent
typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens
instruktion.
(German)
Achtung
Explosionsgefahr bei Verwendung inkorrekter Batterien.
Als Ersatzbatterien dürfen nur Batterien vom gleichen Typ oder
vom Hersteller empfohlene Batterien verwendet werden.
Entsorgung der gebrauchten Batterien nur nach den vom
Hersteller angegebenen Anweisungen.
UX-510UA
FO-1470U
CHAPTER 1. GENERAL DESCRIPTION
[1] Specifications
Automatic dialing:
Rapid Key Dialing: 36 numbers
Speed Dialing: 63 numbers
Imaging film:
Initial starter roll (included with
machine): Approx. 60 letter-size pages
Replacement roll:
UX-15CR/FO-15CR (One roll yields
approx. 500 letter-size pages)
Effective scanning width:
8.2" (208 mm) max.
Effective printing width:
8.1" (206 mm) max.
Contrast control:
Automatic/Dark selectable
Reception modes:
TEL/FAX/A.M. (Note: A.M. mode is for
connecting an answering machine)
Copy function:
Single/Multi/Sort (99 copies/page)
Memory size* :
512 KB (approx. 30 average pages with
ECM turned off)
Telephone function:
Yes
(cannot be used if power fails)
Modem speed:
14,400 bps with Automatic Fallback to
2400 bps.
Power requirements:
120 V AC, 60 Hz
Operating temperature:
41 to 95°F (5 to 35°C)
Humidity:
Maximum: 80 % RH
Power consumption:
Stand-by: 3.6 W
Transmission time* :
Approx. 6 seconds
Resolution:
Horizontal:
203 pels/inch (8 dots/mm)
Vertical:
Standard: 98 lines/inch
(3.85 lines/mm)
Fine/Halftone: 196 lines/inch
(7.7 lines/mm)
Super fine: 391 lines/inch
(15.4 lines/mm)
Maximum: 100 W
Dimensions:
Depth: 19.0" (482 mm)
(With attachments)
Height: 10.6" (270 mm)
(With attachments)
Automatic document feeder: 20 sheets max.
Recording system:
Thermal transfer recording
Halftone (grayscale):
64 levels
Display:
7 x 5 dots, 1 line by 16-digit display
Paper tray capacity:
(16-to 20-lb. paper)
Letter: 200 sheets
Legal: 200 sheets
Compression scheme:
MH, MR, MMR
Applicable telephone line:
Public switched telephone network
Compatibility:
ITU-T (CCITT) G3 mode
Input document size:
Automatic feeding:
Width  5.83 to 8.5"
(148 to 216 mm)
Length  5.04 to 11"
(128 to 279 mm)
Manual feeding:
Width  5.83 to 8.5"
(148 to 216 mm)
Length  5.04 to 39.4"
(128 to 1000 mm)
Width: 14.4" (365 mm)
Weight:
*
Approx. 10.6 lbs. (4.8 kg)
Based on ITU-T (CCITT) Test Chart #1 at standard resolution in Sharp
special mode, excluding time for protocol signals (i.e., ITU-T phase C
time only).
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product
improvement without prior notice. The performance specifications figures indicated are nominal values of production units. There may be some
deviation from these values in individual units.
1–1
UX-510UA
FO-1470U
[2] Operation panel
1 2 3
4 5
6 7
TEL FAX
ABC
1
GHI
2
JKL
4
PQRS
DEF
3
MNO
5
TUV
7
SPEED
DIAL
8
02
03
19
20
21
04
05
06
07
22
23
24
25
08
09
10
11
26
27
28
29
12
13
14/POLL
15/P1
30
31
32
33
16/P2
17/G1
18/G2
34
35
36
REDIAL
VOLUME
DOWN
UP
6
WXYZ
01
SHIFT
A.M.
8
HOLD/
SEARCH
9
RECEPTION
MODE
FUNCTION RESOLUTION
COPY/
HELP
START
MEMORY
STOP
SPEAKER
0
OpenLCR
OpenLCR
PANEL RELEASE
18
17 16 15 14 13 12
1. REDIAL key
Press this key to adjust the resolution for faxing or copying.
11. STOP key
Press this key to cancel an operations before they are
completed.
Press this key to dial a fax or voice number using an
abbreviated 2-digit Speed Dial number.
3. RECEPTION MODE key
12. Panel release
Grasp this finger hold and pull toward you to open the operation
panel.
Press this key to select the mode of reception.
4. Display
This displays messages and prompts during operation and
programming.
5. VOLUME keys
Press these keys to adjust the volume of the speaker when
the @SPEAKER key has been pressed, the volume of the
handset when the handset is lifted, or the volume of the
ringer at all other times.
6. MEMORY key
Press this key to scan a document into memory before
transmitting it.
7. SHIFT key
13. START key
Press this key to begin transmission when using Speed
Dialing, Direct Keypad Dialing, or Normal Dialing.
14. COPY/HELP key
When a document is in the feeder, press this key to make
a copy of a document. At any other time, press this key to
print out the Help List, a quick reference guide to the
opeation of your fax machine.
15. FUNCTION key
Press this key to select various special functions.
16. SPEAKER key
Press this key to listen to the line and fax tones through
the speaker when faxing a document.
Note: This is not a speakerphone. You must pick up the
handset to talk with the other party.
Press this key before pressing the Rapid key.
8. Rapid Dial keys
Press one of these keys to dial a fax number automatically.
9. Open LCR key
Press this key to register for Open LCR service and
receive carrier rate data to your fax.
9
10. RESOLUTION key
Press this key to automatically redial the last number dialed.
2. SPEED DIAL key
11 10
17. HOLD/SEARCH key
Press this key to search for an auto-dial number, or,
during a phone conversation, press this key to put the
other party on hold.
18. Number keys
Use these keys to dial numbers, and enter numbers and letters
when storing auto-dial numbers.
1–2
UX-510UA
FO-1470U
[3] Transmittable documents
5. Automatic Document Feeder Capacity
1. Document Sizes
Number of pages that can be placed into the feeder at anytime is as
follows:
Normal size
width
5.83" – 8.5"(148 – 216 mm)
Normal size: max. ADF 20 sheets
length
5.04" – 11"(128 – 279 mm)
Special size: single sheet only (manual feed)
NOTES:
(Max.)
(Min.)
128mm
148mm
(Max.)
Letter
size
•
1000mm
When you need to send or copy more pages than the feeder
limit, place additional pages in feeder when last page in
feeder is being scanned.
Place additional pages carefully and gently in feeder.
If force is used, double-feeding or a document jam may
result.
279mm
6. Readable Width & Length
216mm
[Normal size]
The readable width and length of a document are slightly smaller than
the actual document size.
216mm
[Special size]
Note that characters or graphics outside the effective document scanning range will not be read.
Use document carrier sheet for smaller documents.
*
•
•
With special sizes, only one sheet can be fed into the machine at a
time. Insert next page into feeder as current page is being scanned.
Readable width
8.1" (206mm), max.
2. Paper Thickness & Weight
4x6 series
(788mm x 1091mm x
1000 sheets)
Minimum
Feeder capacity
Paper weight
Maximum
Square
meter series
Minimum
Maximum
52g/m2
74.3g/m2
20 sheets, max.
45kg
64.3kg
Paper thickness (ref.) 0.06mm
0.09mm
0.06mm
0.09mm
Paper size
128mm x 148mm ~ (MIN. SIZE)
A4 (210mm x 297mm), Letter (216mm x 279mm)
Readable width
3. Document Types
•
Normal paper
•
Documents handwritten in pencil (No. 2 lead or softer), fountain
pen, ball-point pen, or felt-tipped pen can be transmitted.
This is the length of the document sent minus 0.2" (5mm) from the top
and bottom edges.
Readable length
Documents of normal contrast duplicated by a copying machine
can also be transmitted.
•
Diazo copy (blue print)
•
Carbon copy
0.2"(5mm)
Diazo copy documents of a normal contrast may be transmitted.
Readable length
A carbon copy may be transmitted if its contrast is normal.
0.2"(5mm)
4. Cautions on Transmitting Documents
•
Documents written in yellow, greenish yellow, or light blue ink cannot
be transmitted.
•
Ink, glue, and correcting fluid on documents must be dry before
the documents can be transmitted.
•
All clips, staples and pins must be removed from documents before transmission.
•
Patched (taped) documents should be copied first on a copier and
then the copies used for transmission.
•
All documents should be fanned before insertion into the feeder to
prevent possible double feeds.
1–3
UX-510UA
FO-1470U
7. Use of Document Carrier Sheet
TELEPHONE JACK
A document carrier sheet must be used for the following documents.
A standard RJ11C telephone jack must be located near the machine.
This is the telephone jack commonly used in most homes and offices.
•
Those with tears.
•
Those smaller than size 5.83" (W) x 5.04" (L) (148 mm (W) x 128 mm
(L)).
•
Carbon-backed documents
•
Plugging the fax machine into a jack which is not a RJ11C jack may
result in damage to the machine or your telephone system. If you do
not know what kind of jack you have, or needed to have one installed,
contact the telephone company.
2. Loading the imaging film (UX-15CR/FO-15CR)
Make print straight
across paper
E.G.
Place the document
carrier in the document
feeder with the clear film
side down
Your fax uses a roll of imaging film to create printed text and images.
The print head in the fax applies heat to the imaging film to transfer ink to
the paper. Follow the steps below to load or replace the film.
•
The initial starter roll of imaging film included with your fax can print
about 60 letter-size pages.
•
When replacing the film, use a roll of Sharp UX-15CR/FO-15CR
imaging film. One roll can print about 500 letter-size pages.
1 Press the release marked OPEN and open the print compartment
Direction of insertion
cover.
NOTE: To transmit a carbon-backed document, insert a white sheet of
paper between the carbon back of the document and the document carrier.
•
•
Those containing an easily separable writing substance (e.g., tracking paper written on with a soft, heavy lead pencil).
NOTES:
•
When using the document carrier, carefully read the instructions written on the back.
•
If the document carrier is dirty, clean it with a soft, moist
cloth, and then dry it before using for transmission.
•
Do not place more than one document in the carrier at a
time.
Caution! The printing head (the strip of metal on the underside of
the cover) applies heat to the printing film. It may be hot
if a document has just been printed.
[4] Installation
1. Site selection
Take the following points into consideration when selecting a site for this
model.
ENVIRONMENT
•
The machine must be installed on a level surface.
•
Keep the machine away from air conditioners, heaters, direct sunlight, and dust.
•
Provide easy access to the front, back, and sides of the machine. In
particular, keep the area in front of the machine clear, or the original
document may jam as it comes out after scanning.
•
The temperature should be between 5° and 35°C.
•
The humidity should be between 30% and 85% (without condensation).
2 If you are replacing the imaging film, take the old film out of the print-
ing compartment and remove the three (3) green gears and the green
flange from the ends of the spools.
DO NOT DISCARD THE GREEN GEARS AND THE GREEN
FLANGE!
ELECTRICITY
AC 120V, 60Hz, grounded (3-prong) AC outlet is required.
Caution!
•
Connection to a power source other than that specified will cause
damage to the equipment and is not covered under the warranty.
•
If your area experiences a high incidence of lightning or power surges,
we recommend that you install a surge protector for the power and
telephone lines. Surge protectors can be purchased at most telephone
speciality stores.
If the machine is moved from a cold to a warm place...
Condensation may form on the reading glass if machine is moved from
a cold to a warm place, this will prevent proper scanning of documents
for transmission. Turn on the power and wait approximately 2 hours before using machine.
1–4
UX-510UA
FO-1470U
3 Take the new film out of its package, and insert two of the gears
7 Insert the empty spool into the back of the compartment so that the
provided with the fax into the ends of the spool with film. Make sure
that the two tabs on the gears fit properly into the slots in the ends of
the spool.
•
gear and the flange fit into the slots on the sides of the compartment.
•
Make sure that the gear engages with the gear below it.
Do not yet remove the band which holds the spools together.
8 Wind the film slightly (rotate the gear on the right side of the empty
2 tabs
4 Hold the empty spool so that the end with only one slot is on the left,
spool) so that there is no slack in the film. Make sure that both edges
of the film wind onto the spool evenly.
and lower the spools into the front of the printing compartment. The
gears in the ends of the spool with film should fit into the slots on
each side of the printing compartment.
9 Close the print compartment cover, making sure it clicks into place.
5 Cut the band which holds the spools together with scissors, and re-
•
move it. Insert the remaining gear into the right end of the empty
spool and the flange into the left end of the empty spool. Make sure
the tabs on the gear and the flange fit into the slots in the ends of the
spool (the gear has two tabs and the flange has one tab).
Caution! Close the cover slowly to make sure it doesn’t pinch your
fingers.
1 tab
Flange
2 tabs
Gear
F Load paper in the paper tray and then press the following keys to
initialize the film.
6 Pull the empty spool toward the back of the compartment, unwind-
Note: Paper must be loaded before the film can be initialized. To load
paper, see Loading the Printing Paper.
ing the film as you pull.
FUNCTION
Display shows:
6
START
INITIALIZE FILM
When to replace the imaging film
Replace the imaging film when the display shows:
FILM END
Use the following imaging film, which is available from your dealer
or retailer: Sharp UX-15CR/FO-15CR Imaging Film
•
1–5
Caution! The text of documents printed with the imaging film is
visible on the used film. If confidential information has
been printed, dispose of the film appropriately.
UX-510UA
FO-1470U
4 Insert the paper tray into the back of the fax as shown.
3. Assembly and connections
1 Plug the power cord into a 120V, 60Hz, grounded(3-prong) outlet.
•
Caution: Do not plug the power cord into any other kind of outlet.
This will damage the machine and is not covered under the
warranty.
•
The machine does not have a power on/off switch, so the power
is turned on and off by simply plugging in or unplugging the power
cord.
Note: If your area experiences a high incidence of lightning or power
surges, we recommend that you install surge protectors for
the power and telephone lines. Surge protectors can be
purchased at most telephone specialty stores.
4. Loading printing paper
The paper tray holds the paper on which received documents and
copies are printed. Up to 200 sheets of letter or legal paper from
2
16 to 20 lbs. (60 to 75 g/m ) can be loaded in the tray. Less sheets can
be loaded when using heavier paper. The maximum allowed paper
2
weight is 24 lbs. (90 g/m ).
2 Connect the handset as shown and place it on the handset rest.
Note: When receiving or copying documents, do not allow more than
100 pages to collect in the received documents outlet. Otherwise,
the outlet may become obstructed, causing paper jams.
Make sure the handset cord
goes into the unmarked jack
on the side of the machine!
• Caution! Do not use the blank side of paper that has already been
printed on.
1 Remove the paper cover if it is on the paper tray.
Use the handset to make ordinary
phone calls, or to transmit and receive
faxes manually.
•
If you are going to load legal size paper, flip up the paper tray
extender.
3 Insert one end of the line cord into the jack on the back of the ma-
chine marked TEL.LINE. Insert the other end into a standard (RJ11C)
single-line wall telephone jack.
Be sure to insert the line into the TEL.LINE jack.
Do not insert into the TEL.SET jack.
TE
SEL. T
T EL
LI .
NE
Note: The fax machine is set for tone dialing. If you are on a pulse
dial line, you must set the fax machine for pulse dialing.
Press the keys on the operation panel as follows:
2 Fan the paper, and then tap the edge against a flat surface to even
the stack.
1. Press these keys:
The display will show:
FUNCTION
4
DIAL MODE
2. Press 1 to select tone dialing, or 2
to select pulse dialing.
3. Press the STOP key to return to the date
and time display.
TONE
1
PULSE
or
2
STOP
1–6
UX-510UA
FO-1470U
3 Pull the paper release plate toward you and insert the stack of paper
5 The fax has been set at the factory to scale the size of received faxes
into the tray, print side down.
•
to letter size paper. If you have loaded legal paper, you must change
the paper size setting to legal. Press these keys:
If paper remains in the tray, take it out and combine it into a single
stack with the new paper before adding the new paper.
FUNCTION
6
The display will show: PAPER SIZE SET
Press 1 to select LETTER, 2 to select LEAGAL.
LETTER
1
LEAGAL
2
or
The display will show: COPY CUT-OFF
STOP
Press the STOP key to return to the date and time display.
6 Your fax has been set at the factory to print at normal contrast.
Depending on the type of paper you have loaded, you may find that
you obtain better print quality by changing the setting to LIGHT.
Press these keys:
FUNCTION
The display will show: PRINT CONTRAST
4 Replace the paper cover on the paper tray.
•
Press 1 to select NORMAL or 2 to select LIGHT.
NORMAL
1
Important: Be sure to replace the paper cover before you put
back the paper release plate down.
6
LIGHT
or
2
The display will show: PAPER SIZE SET
STOP
Press the STOP key to return to the date and time display.
Note: If the display shows the following alternating messages when
making a copy or receiving a fax, check the paper tray. If the tray is
empty, add paper and then press the START key. If there is paper,
make sure it is inserted correctly and then press the START key.
5. Clearing paper jams
If a document doesn’t feed properly during transmission or copying, or
DOCUMENT JAMMED appears in the display, first try pressing the
START key. If the document doesn’t feed out, open the operation panel
(grasp the front edge at the "PANEL RELEASE" mark and pull up) and
pull it out gently.
SET PAPER &
↑
↑
PRESS START KEY
1 Press the release marked OPEN and open the print compartment
cover.
•
1–7
Caution! The printing head (the strip of metal on the underside of
the frame) applies heat to the imaging film. It may be hot
if a document has just been printed.
UX-510UA
FO-1470U
2 Remove the imaging film from the printing compartment and set it on
5 Wind the film slightly (rotate the gear on the right side of the rear
3 Gently pull the jammed paper out of the printing compartment.
6 Close the print compartment cover, making sure it clicks into place.
a sheet of paper.
spool) so that there is no slack in the film. Make sure that both edges
of the film wind onto the spool evenly.
•
4 Replace the imaging film, making sure that the flange goes into the
rear slot on the left side of the printing compartment. Also, make sure
that the right, rear gear engages with the gear below it.
1–8
Caution! Close the cover slowly to make sure it doesn’t pinch your
fingers.
UX-510UA
FO-1470U
SENDING FAXES
[5] Quick reference guide
ENTERING YOUR NAME AND NUMBER
1. Press:
FUNCTION
3
Display shows: OWN NUMBER SET
Place your document (up to 20 pages)
face down in the document feeder.
START
2. Press:
3. Enter your fax number (max. of 20 digits) by pressing the number keys.
♦ To insert a space between digits, press the # key.
♦ If you make a mistake, press the SPEED DIAL key to backspace and clear the
mistake.
START
4. Press:
5. Enter your name by pressing the appropriate number keys as shown below.
♦ To enter two letters in succession that require the same key, press the SPEAKER
key after entering the first letter.
Normal Dialing
SPEAKER
1. Lift the handset or press:
SPACE =
J=
T=
2. Dial the fax number.
A=
K=
U=
3. Wait for the reception tone (if a person answers, ask them to press their Start
key).
B=
L=
V=
C=
M=
W=
D=
START
4. Press:
Rapid Key Dialing
Press the appropriate Rapid Key (if the Rapid Key is from 19 to 36, press the
SHIFT key first).
Transmission will begin automatically.
N=
X=
E=
O=
Y=
F=
P=
Z=
G=
Q=
H=
R=
1. Press:
I=
S=
2. Enter 2-digit Speed Dial number.
Speed Dialing
SPEED
DIAL
START
•
3. Press:
To change case, press the REDIAL key.
Press # or to scroll through symbols and special characters.
START
RECEIVING FAXES
STOP
6. When finished, press:
Press the RECEPTION MODE key until the appears in the display points to the
desired reception mode.
TEL FAX
SETTING THE DATE AND TIME
1. Press:
FUNCTION
RECEPTION
MODE
3
NOV 05 10:30
A.M.
TEL FAX
NOV 05 10:30
Display shows: DATE & TIME SET
A.M.
START
2. Press:
TEL FAX
NOV 05 10:30
3. Enter two digits for the month (01 to 12).
A.M.
4. Enter two digits for the day (01 to 31).
FAX mode: The fax machine automatically answers on four rings and receives the
incoming document.
5. Enter four digits for the year (Ex: 2000).
TEL mode:
6. Enter two digits for the hour (01 to 12)
and two digits for the minute (00 to 59).
7. Press
START
Beep
for A.M. or # for P.M.
START
STOP
8. When finished, press:
STORING AND CLEARING AUTO DIAL NUMBERS
1. Press:
FUNCTION
RECEIVING
3
Display shows: FAX/TEL # MODE
A.M. mode: Select this mode when an answering machine is connected to the fax
and the answering machine is turned on.
2. Press 1 to store a number or 2 to clear a number.
3. Enter a 2-digit number (from "01" to "99") by pressing the number keys. This
will be the Speed Dial number. (If you are clearing a number, go to Step 7.)
4. Enter the full fax/telephone number.
START
5. Press:
6. Enter the name of the location by pressing number keys (Refer to the letter
entry table in ENTERING YOUR NAME AND NUMBER.)
START
STOP
7. Press:
1–9
UX-510UA
FO-1470U
MEMO
1 – 10
UX-510UA
FO-1470U
CHAPTER 2. ADJUSTMENTS
3. Settings
(1) Dial mode selector
[1] Adjustments
DIAL mode (Soft Switch No. SWB4 DATA No. 3)
(step 1) Select "OPTION SETTING".
General
KEY :
FUNCTION
Since the following adjustments and settings are provided for this model,
make adjustments and/or setup as necessary.
DISPLAY:
OPTION SETTING
4
PRESS
OR #
(step 2) Select "DIAL MODE".
1. Adjustments
KEY:
Push # until " DIAL MODE " is
indicated because the number of
# s changes by the model.
Adjustments of output voltage (FACTORY ONLY)
1. Install the power supply unit in the machine.
2. Set the recording paper and document.
DISPLAY:
3. When the document is loaded, power is supplied to the output lines.
Confirm that outputs are within the limits below.
TEL/LIU
PWB
POWER
SUPPLY
PWB
CNPW
CONTROL
PWB
KEY:
1
DISPLAY:
TONE SELECTED
KEY:
2
DISPLAY:
PULSE SELECTED
(step 4) End, using the "STOP" key.
KEY:
CNLIUA
1=TONE, 2=PULSE
(step 3) Select, using "1" or "2".
Output voltage settings
CNTH
DIAL MODE
Cursor
When initially registering,
the mode shows 1=TONE.
When registering again, the
mode which was registered
formerly is shown.
STOP
4. Volume adjustment
CNLIUA
You can adjust the volume of the speaker and ringer using the UP and
DOWN keys.
CNLED
CNMT
(1) Speaker
1Press the SPEAKER key.
2Press the UP or DOWN key.
CNSP
CNCSW
CNPN
CNCCD
Display:
Connector
No.
Pin No.
1
2
3
4
5
6
SPEAKER: HIGH
CNPW
↔
Voltage limits
4.75V ∼ 5.25V
23.3V ∼ 24.7V
SPEAKER: MIDDLE
+24V
+24V
MG
MG
+5V
DG
↔
Output
+5V
+24V
SPEAKER: LOW
3When the display shows the desired volume level, press the SPEAKER
key to turn off the speaker.
(2) Handset
1Lift the handset.
2Press the UP or DOWN key.
2. IC protectors replacement
Display:
RECEIVER: HIGH
The location of ICPs are shown below:
RECEIVER: MIDDLE
↔
↔
ICPs (IC Protectors) are installed to protect the motor driver circuit.
ICPs protect various ICs and electronic circuits from an overcurrent condition.
RECEIVER: LOW
3When the display shows the desired volume level, replace the hand-
CONTROL
PWB (TOP SIDE)
set.
(3) Ringer
been pressed and the handset is not lifted.)
Display:
,
FU100
↔
RINGER: HIGH
RINGER: MIDDLE
↔
CNLIUA
1Press the UP or DOWN key. (Make sure the SPEAKER key has not
The ringer will ring once
at the selected level, then
the date and time will reappear in the display.
RINGER: LOW
↔
(1) FU100 (KAB2402) is installed in order to protect IC’s from an overcurrent generated in the motor drive circuit. If FU100 is open, replace
it with a new one.
RINGER OFF: OK?
2If you selected RINGER OFF: OK?, press the START key.
2–1
UX-510UA
FO-1470U
[2] Diagnostics and service soft switch
1. Operating procedure
(1) Entering the diagnostic mode
Press FUNC → 9 →
ROM Ver. FPS0
→ 8 → # → 7 , and the following display will appear.
After 2 sec: DIAG MODE
FPS0
Then press the START key. Select the desired item with the
key or the # key or select with the rapid key. Enter the mode with the START key.
(Diag•specifications)
FUNC
9
8
FPS0
7
DIAG MODE
START
Soft switch mode
START
1
12
START
Entry data receive
ROM & RAM check
START
2
11
START
Entry data send
Aging mode
START
3
10
START
Auto feeder mode
Panel key test
START
4
9
START
All black mode
Check pattern
START
5
8
START
CCD adjust mode
Signal send mode
START
6
7
START
Memory clear
If the diag mode cannot be set, repeat the diag mode operation, performing the following operation.
After the power is turned on and "WAIT A MOMENT" is indicated, press
the STOP key.
STOP
KEY
START
KEY
In relation with the process response (request from Production
Engineering) "WAIT A MOMENT" clock indication may appear depending on STOP key timing. If the STOP key is held down,
"MEMORY CLEAR?" appears.
"Power ON" +
Memory clear
(Work + Backup)
2. Diagnostic items
ITEM
DIRECT
No.
key
1
1
SOFT SWITCH MODE
Soft switches are displayed and changed. List can be output.
2
2
ROM & RAM CHECK
ROM is sum-checked, and RAM is matched. Result list is output.
3
3
AGING MODE
10 sheets of check patterns are output every 5 minutes per sheet.
4
4
PANEL KEY TEST
Panel keys are tested. Result list is output.
5
5
CHECK PATTERN
Check pattern is output.
6
6
SIGNAL SEND MODE
Various signals of FAX communication are output.
7
7
MEMORY CLEAR
Back-up memory is cleared, and is set at delivery.
8
8
CCD ADJUST MODE
Optical system is adjusted.
9
9
ALL BLACK PRINT
To check the print head, whole dots are printed over the interval of 2 m.
10
10
AUTO FEEDER MODE
Insertion and discharge of document are tested.
11
11
ENTRY DATA SEND
Registered content is sent.
12
12
ENTRY DATA RECEIVE
Registered content is received, and its list is output.
Contents
Function
2–2
UX-510UA
FO-1470U
3. Diagnostic items description
3. 1. Soft switch mode
3. 6. Signal send mode
This mode is used to send various signals to the circuit during FAX communication. Every push of START key sends a signal in the following
sequence. Moreover, the signal sound is also output to the speaker when
the line monitor of the soft switch is on.
Used to change the soft switch settings.
The soft switch which is stored internally is set by using the keys.
The available soft switches are SW-A1 to SW-N3.
[1] No signals (CML ON)
The content of soft switches is shown in page 2-5 to 2-18.
[2] 14400BPS (V.33)
The contents are set to factory default settings.
[3] 12000BPS (V.33)
[4] 14400BPS (V.17)
3. 2. ROM & RAM check
[5] 12000BPS (V.17)
ROM executes the sum check, and RAM executes the matching test.
The result will be notified with the number of short sounds of the buzzer
as well as by printing the ROM & RAM check list.
Number of short sounds of buzzer 0 → No error
[6] 9600BPS (V.17)
[7] 7200BPS (V.17)
[8] 9600BPS (V.29)
1 → ROM error
[9] 7200BPS (V.29)
2 → RAM error (32Kbyte)
[10] 4800BPS (V27ter)
3. 3. Aging mode
[11] 2400BPS (V27ter)
If any document is first present, copying will be executed sheet by sheet.
If no document is present, the check pattern will be printed sheet by
sheet. This operation will be executed at a rate of one sheet per 5minutes, and will be ended at a total of 10 sheets.
[12] FLAG
[13] 2100Hz
[14] 1100Hz
3. 4. Panel key test
3. 7. Memory clear
This mode is used to check whether each key operates properly or not.
Press the key on the operation panel, and the key will be displayed on
the display. Therefore, press all keys. At this time, finally press the STOP
key.
This mode is used to clear the backup memory and reset to the default
settings.
When the STOP key is pressed, the keys which are not judged as
"pressed" will be printed on the result list.
This mode is used to adjust the optical system. Since the copy is function performed, set the original. To abort the copy operation, press the
STOP key. To restart press the START key. When the copy is completed
or when the STOP key is pressed in the interruption state, exit from this
mode occurs.
3. 8. CCD adjust mode
• LED part of the contact image sensor (CIS) is kept on during the term
from when "START" of the panel test mode to end with the STOP key.
3. 5. Check pattern
3. 9. All black print
This mode is used to check the state of the printing head. It is ended
with the following pattern printed on one printing sheet.
This mode is used to check the state of the printing head and intentionally overheat it. Whole dots are printed over the interval of 2 m. If it is
overheated or the printing sheet is jammed, press STOP key for the end.
1 Longitudinal stripe 2 Approx. 30 mm
2 black dots and 2 white dots are repeatedly progressed on one
line.
2 Full black
3. 10. Auto feeder mode
Approx. 30 mm
In this mode, a document is inserted and discharged to check the auto
feed function.
1
After this mode is started, set a document, and the document feed will
be automatically tested.
3. 11. Entry data send
2
This mode is used to send the registered data to the other machine and
make the other machine copy the registered content.
Before sending in this mode, it is necessary to set the other machine at
the entry data receive mode.
The following, information will be sent to the remote machine:
1. Telephone list data
2. Sender register data
3. Optional setting content
4. Soft switch content
5. Junk fax number list
6. Timer reservation data (only on the model which timer reservation is possible)
7. Recording setting list data
2–3
UX-510UA
FO-1470U
3. 12. Entry data receive
In this mode, the registered data sent from the other machine is received and the received data is registered in the machine. When this mode
is used for receiving, the other machine must be in the entry data send
mode.
After receiving is completed, the following lists are printed.
1. Telephone list data
2. Sender register data (The passcode No. is also printed if the polling
function is provided.)
3. Optional setting list
4. Soft switch content
5. Junk fax number list
6. Timer reservation list (only model which timer communication is
possible)
7. Recording setting list data
4. How to make soft switch setting
To enter the soft switch mode, press the following key entries in sequence.
Press FUNCTION
DATA No.
9
8
7
START
START
1 2 3 4 5 6 7 8
S F T SW-A1 = 0 0 0 0 0 0 0 0
Press FUNCTION key.
S F T SW-A1 = 1 0 0 0 0 0 0 0
Press
key.
Press
key.
S F T SW-A1 = 1 0 0 0 0 0 0 0
S F T SW-A1 = 1 0 0 0 0 0 0 0
Bit1 - 8 are set.
S F T SW-A1 = 1 0 0 0 0 0 0 0
Press START key during setting.
S F T SW-A2 = 0 0 0 0 0 0 0 0
Soft SW-A2 - SW-N3 are set.
S F T SW-N3 = 0 0 0 0 0 0 0 0
To finish the settings halfway between
SW-A1 and SW-N3, press the STOP
key. In this case, the setting being done
to the SW No. on display will be nullified
while settings done to the preceding
SW Nos. remain in effect.
When the COPY key is pressed, the
contents of soft switches are printed.
The soft switch mode is terminated.
2–4
UX-510UA
FO-1470U
5. Soft switch description
• Soft switch
SW
NO.
SW
l
A1
DATA
NO.
Switch setting and function
ITEM
1
Initial
setting
0
1
Protect from echo
No
Yes
2
Forced 4800 BPS reception
Yes
No
0
3
Footer print
Yes
No
0
4
Length limitation of copy/send/receive
No limit
Copy/send: 1m
0
Remarks
0
Receive: 1.5m
5
CSI transmission
No transmitted
Transmitted
0
6
DIS receive acknowledgement during G3
transmission
Twice
NSF: Once
DIS: Twice
0
7
Non-modulated carrier for V29 transmission
modem
Yes
No
0
8
EOL detect timer
25 s
13 s
0
Modem speed
V.33
V.17
V.29
V.27 ter
14400 12000 14400 12000 9600 7200 9600 7200 4800 2400
SW
l
A2
1
0
0
1
1
1
1
0
0
0
0
1
2
1
1
0
0
0
0
0
0
0
0
0
3
0
1
0
1
0
1
0
1
1
0
0
4
0
0
0
0
1
1
1
1
0
0
0
5
6
Sender’s information transmit
Reserved
No
Yes
0
0
7
Communication error treatment in RTN
sending mode (reception)
No communication error
Communication error
0
8
CNG transmission
CED tone signal interval
No
1
2
SW
l
A3
Yes
750ms
500ms
75ms
No. 1
1
1
0
0
0
No. 2
1
0
1
0
0
MR coding
No
Yes
0
4
ECM mode
No
Yes
0
5
ECM MMR mode
No
Yes
0
6
Reserved
0
7
Reserved
0
8
Reserved
1
Signal transmission level
No. =
0
16 8 4 2 1
1
3
4
1
0
2 3 4 5
1 0 1 0
0
1
5
0
6
Protocol monitor (error print)
Printed at com. error
Not printed
7
Protocol monitor
Yes
No
0
8
Line monitor
Yes
No
0
0
7.2km
3.6km
1.8km
0km
1
No. 1
1
1
0
0
0
2
No. 2
1
0
1
0
1
7.2km
3.6km
1.8km
0km
No. 3
1
1
0
0
0
No. 4
1
0
1
0
1
Digital line equalization setting
3
(Transmission)
4
Digital cable equalizer setting (Reception
5
OPTION
0
Binary input
Digital line equalization setting (Reception)
SW
l
A5
0
3
2
SW
l
A4
1000ms
7.2km
for Caller ID)
6
0km
No. 5
1
0
1
No. 6
1
0
1
7
Error criterion
10 ~ 20 %
5 ~ 10 %
0
8
Anti junk fax check
Yes
No
0
2–5
OPTION
UX-510UA
FO-1470U
SW
NO.
SW
l
A6
DATA
NO.
Switch setting and function
ITEM
1
Initial
setting
0
1
Auto gain control (MODEM)
Enable
Disable
1
2
End Buzzer
Yes
No
1
3
Disconnect the line when DIS is received in
RX mode
No
Yes
1
4
5
Equalizer freeze control (MODEM)
Equalizer freeze control 7200BPS only
On
No
Off
Yes
0
0
6
7
CNG transmission in manual TX mode
Reserved
Yes
No
1
0
8
Modem speed automatic fallback when RX
Yes
No
0
Remarks
level is under -40dBm
1
Recall interval
2
3
SW
l
B1
No. =
4
5
Recall times
6
SW
l
B2
SW
l
B3
No. =
0
2
3
1
4
1
0
0 1
0
1
1
Binary input
0
8
4
2
1
0
7
5
6
7
8
1
8
0
0
1
0
Dial pausing (sec/pause)
4 sec
2 sec
2
Dial tone detection (before outo dial)
No
Yes
3
Reserved
4
Busy tone detection (after auto dial)
0
1
No
Yes
0
45 seconds 55 seconds 90 seconds 140 seconds
5
No.5
0
0
1
1
6
No.6
0
1
0
1
0
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
6
Auto dial mode Delay timer of before line
connect
7
8
Hold key
1
Auto dial mode Delay timer of after line
connect
0
0 second
0
No.6
No.7
Enable
3
4
Dial mode
Pulse → Tone change function by
5
Dial pulse make/break ratio (%)
6
Reserved
7
Reserved
8
Recalling fixed only one time when dialing was
key
1.5 seconds 3.0 seconds 4.5 seconds
0
1
1
0
1
Disable
0
1
1.7 seconds 3.0 seconds 3.6 seconds 4.0 seconds
0
0
1
1
No.1
No.2
0
1
0
1
0
0
1
0
0
Tone
Enable
Pulse
Disable
1
1
40/60
33/67
1
0
0
Yes
No
1
unsuccessful without detecting busy tone signal
DTMF signal transmission level (Low)
2
SW
l
B5
OPTION
0
Waiting time after dialing
1
OPTION
0
1
2
SW
l
B4
Binary input
8 4
1 2
No. =
Binary input
0
16 8 4 2 1
1
3
4
1
0
5
2 3 4 5
1 0 1 1
0
1
1
6
Reserved
0
7
Reserved
0
8
Reserved
0
2–6
OPTION
UX-510UA
FO-1470U
SW
NO.
DATA
NO.
1
Switch setting and function
ITEM
1
DTMF signal transmission level (High)
2
SW
l
B6
No. =
Binary input
0
16 8 4 2 1
0
1 2 3 4 5
0 0 1 1 1
1
1
3
4
5
6
Dial tone detection (LCR center call)
7
8
Reserved
Reserved
No
Yes
0
0
0
Factory
Light
Dark
setting
No. 1
0
1
0
1
0
No. 2
0
Factory
0
Light
1
Dark
1
Darker in
0
setting
dark
3
No. 3
0
1
0
1
0
4
No. 4
0
0
1
1
0
5
6
Line density selection
Reserved
Fine
Standard
0
0
7
8
MTF correction in half tone mode
Reserved
No
Yes
0
0
1
Number of rings for auto receive
No. =
3
4
5
6
Automatic switching manual to auto receive
mode
Binary input
0
8
4
2
1
1
1
2
3
4
0
0
1
0
0
Reception after 5 rings
7
No.8
0
No. 1
Distinctive ringing setting
(PATTERN 4 and 5 are for CANADA only)
0
OFF
0
11.5Hz
0
13.0Hz
1
1
0
20.0Hz
1
No. 2
1
No. 3
0
0
STANDARD
0
0
1
PATTERN1
0
1
0
0
0
OPTION
PATTERN2
0
1
1
1
PATTERN3
1
0
0
0
2
PATTERN4
1
0
1
0
3
PATTERN5
1
1
0
4
Reserved
5
6
Caller ID function
Caller ID detect during CI off
7
8
Reserved
Reserved
1
Cl off detection timer (0-1550ms setting by
2
50ms step)
OPTION
0
As PTT
0
No.7
8
OPTION
0
No reception
Reserved
Cl detect frequency
SW
l
D3
dark
2
2
SW
l
D2
Darker in
1
Reading slice (Half tone)
SW
l
D1
Remarks
1
Reading slice (Binary)
SW
l
C1
Initial
setting
0
0
0
Yes
All times
No
Only first
0
0
0
0
Binary input
0
16 8 4 2 1
1
3
1 2 3 4 5
1
4
5
0 1 1 1 0
1
0
No. =
6
7
Reserved
Reserved
0
0
8
Reserved
0
2–7
OPTION
UX-510UA
FO-1470U
SW
NO.
SW
l
E1
SW
l
E2
SW
l
E3
DATA
NO.
Switch setting and function
ITEM
1
1
Reserved
0
2
3
Reserved
Reserved
0
0
4
Reserved
0
5
Reserved
0
6
7
Reserved
Reserved
0
0
8
Reserved
0
1
Reserved
0
2
3
Reserved
Reserved
0
0
4
Reserved
0
5
Reserved
0
6
7
Reserved
Reserved
0
0
8
Reserved
0
1
Reserved
0
2
3
Reserved
Reserved
0
0
4
Reserved
0
5
Reserved
0
6
7
Reserved
Reserved
0
0
8
Reserved
1
2
3
Protection of remote reception (5
4
Remote reception with GE telephone
5
6
Remote operation code figure by external
TEL (0~9)
) detect
50ms
80ms
100ms
120ms
No. 1
0
0
1
1
0
No. 2
0
1
0
1
0
Yes
No
0
Compatible
Not compatible
1
Binary input
8 4 2 1
0
1
7
5
6
7
8
0
8
0
1
0
1
1
CNG detection in STAND-BY mode
No. =
Yes
SW
l
G1
1
2
No. 2
1pulse
0
3
No. 3
0
1
0
1
1pulse
2pulses
3pulses
4pulses
Number of CNG detect (STAND-BY mode)
2pulses
0
3pulses
1
4pulses
1
0
1
4
No. 4
0
0
1
1
0
5
6
No. 5
0
1
0
1
Reserved
1
0
7
Reserved
0
8
Reserved
1
2
Quiet detect time
0
1
3
1
2
3
4
0
4
0
1
0
0
0
No. =
Binary input
0
8
4
2
1
1
7
5
6
7
8
0
8
0
1
0
1
1
6
OPTION
OPTION
0
Binary input
8 4 2 1
5
OPTION
1
No
Number of CNG detect (AM mode)
SW
l
F2
Remarks
0
DTMF detection time
SW
l
F1
Initial
setting
0
Quiet detect start timing
No. =
2–8
OPTION
UX-510UA
FO-1470U
SW
NO.
SW
l
G2
DATA
NO.
Switch setting and function
ITEM
1
1
2
Reserved
Reserved
0
0
3
4
Reserved
Reserved
0
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
1
2
3
4
No. 1
No. 2
100ms
200ms
300ms
0
0
0
1
1
0
1
1
0
1
0
Reserved
0
Selection time of quiet detection
30s
40s
50s
60s
5
No. 5
0
0
1
1
0
6
No. 6
0
1
0
1
1
Choice after quiet detect
8
Reserved
Busy tone detection ON/OFF time (Lower
1
Wait response for 3sec
duration)
duration)
4
5
6
Reserved
Busy tone detect continuation sound detect
7
(during ICM: for internal A.M.)
Reserved
8
Busy tone detect intermittent sound detect
1
150ms
200ms
250ms
350ms
No. 1
0
0
1
1
0
No. 2
0
1
0
1
1
650ms
900ms
1500ms
2700ms
No. 3
0
0
1
1
No. 4
0
1
0
1
Busy tone detection ON/OFF time (Upper
3
Normal FAX RX
0
2
SW
l
H1
Not work
Reserved
7
Remarks
0
OGM detect timer
SW
l
G3
Initial
setting
0
No
0
1
0
0
Yes
0
No
Yes
0
(during ICM: for internal A.M.)
Busy tone detection pulse number
1
SW
l
H2
SW
l
I1
SW
l
I2
2pulses
4pulses
6pulses
10pulses
No. 1
0
0
1
1
0
No. 2
0
1
No
0
1
1
0
2
3
Fax switching when A.M. full
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
8
Busy tone continuous sound detect time
1
Reserved
0
2
Reserved
0
3
4
Reserved
Reserved
0
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
3
Reserved
Reserved
0
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
Yes
0
5s
10s
1
0
2–9
OPTION
UX-510UA
FO-1470U
SW
NO.
SW
l
I3
SW
l
I4
SW
l
I5
SW
l
I6
SW
l
I7
SW
l
J1
DATA
NO.
Switch setting and function
ITEM
1
Initial
setting
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
8
Reserved
Reserved
0
0
1
2
Reserved
Reserved
0
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
1
Reserved
Reserved
0
0
2
3
Reserved
Reserved
0
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
2
Reserved
Reserved
0
0
3
Reserved
0
4
Reserved
0
5
6
Reserved
Reserved
0
0
7
Reserved
0
8
1
Reserved
Activity report print
Automatic printout
No printout when memory full
0
0
2
Total communication hours and pages print
No
Yes
0
3
Sender’s phone number setting
Cannot change
Change allowed
4
Reserved
5
Reserved
6
Summer time setting
Remarks
OPTION
0
0
0
No
Yes
Ringer volume
1
Off
Low
Middle
High
7
No. 7
0
0
1
1
1
8
No. 8
0
1
0
1
0
2 – 10
OPTION
OPTION
UX-510UA
FO-1470U
SW
NO.
DATA
NO.
Switch setting and function
ITEM
1
Speaker volume (3 stages)
1
2
3
SW
l
J2
Polling key
Low
Middle
High
0
0
1
1
1
No. 2
0
1
0
1
0
No
Handset receiver volume
5
SW
l
J3
Low
No. 1
Yes
4
Initial
setting
0
OPTION
0
Low
Low
Middle
High
No. 4
0
0
1
1
No. 5
0
1
0
1
OPTION
0
Reserved
0
7
Reserved
0
8
1
Reserved
Automatic cover sheet
2
Communication results printout
(Transaction report)
0
0
No
Send only Always No print Err only
0
0
0
1
OPTION
1
6
Yes
Remarks
No. 2
E/T/M
0
3
No. 3
0
0
1
1
0
0
4
No. 4
0
1
0
1
0
0
OPTION
OPTION
1
5
Reserved
0
6
7
Reserved
Reserved
0
0
8
Reserved
1
Entering DIAG mode by pressing SPEED
0
Yes
No
0
key
SW
l
K1
SW
l
L1
2
Reserved
0
3
Reserved
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
Reserved
0
2
Reserved
0
3
Reserved
0
4
Reserved
5
6
Cut off mode (COPY mode)
A4 paper enable
7
8
0
Yes
Enable
No
Disable
LEGAL & LETTER paper enable
Enable
Disable
1
2 IN 1 Mode
Yes
No
0
Paper set size
1
2
SW
l
L2
SW
l
M1
1
0
LETTER
LEGAL
A4
No. 1
0
0
1
No. 2
0
1
0
OPTION
OPTION
OPTION
0
0
3
Automatic reduce of receive
Auto
100 %
1
OPTION
4
Print contrast
Light
Normal
0
OPTION
5
6
Reception reduction ratio in case of memory full 100 %
Reserved
93 %
0
0
OPTION
7
8
Reserved
Reserved
0
0
1
2
Reserved
Reserved
0
0
3
Reserved
0
4
5
Reserved
Reserved
0
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
2 – 11
UX-510UA
FO-1470U
SW
NO.
SW
l
M2
DATA
NO.
Switch setting and function
ITEM
1
1
Reserved
0
2
3
Reserved
Reserved
0
0
4
Reserved
0
5
Reserved
0
6
Reserved
0
7
Reserved
0
8
Reserved
0
1
LCR short time
2
SW
l
N1
Initial
setting
0
No. =
3
4
Binary input
0
32 16 8 4 2 1
0
1
0
2 3 4 5
0 0 0 1
6
0
5
1
0
7
Reserved
0
8
Reserved
0
1
LCR long time
2
No. =
3
4
Binary input
0
32 16 8 4 2 1
0
1
0
2 3 4 5
0 0 1 0
6
0
5
0
0
7
Reserved
0
8
Reserved
0
1
2
LCR Time Select
Temporary release of caller ID withhold
Long
Yes
Short
No
3
Connect Japanese center
Connect Japanese center
Connect USA center
0
4
Open LCR debug mode
Open LCR debug mode ON
Open LCR debug mode OFF
0
Digital equalization setting (Reception for
5
OPTION
0
1
6
SW
l
N3
OPTION
0
0
6
SW
l
N2
Remarks
LCR V23 mode)
6
0
1
0km
0km
7.2km
7.2km
No. 5
0
0
1
1
0
No. 6
0
1
0
1
0
7
Reserved
0
8
Reserved
0
2 – 12
OPTION
UX-510UA
FO-1470U
SW-A2 No. 8 CNG transmission
• Soft switch function description
When set to "0" , this model allows CNG transmission by pressing the
Start key in the key pad dialing mode. When set to "1", CNG transmission in the key pad dialing mode cannot be performed. In either case.
CNG transmission can be performed in the auto dial mode.
SW-A1 No. 1 Protect from echo
Used to protect from echo in reception.
SW-A1 No. 2 Forced 4800BPS reception
SW-A3 No. 1, No. 2 CED tone signal interval
When line conditions warrant that receptions take place at 4800BPS
repeatedly.
For international communication, the 2100Hz CED tone may act as an
echo suppression switch, causing a communication problem.
It may improve the success of receptions by setting at 4800BPS.
Though SW-A3 No. 1 and No. 2 are normally set to 0, this selfing is used
to change the time between the CED tone signal to eliminate the communication caused by echo.
This improves the receiving document quality and reduces handshake
time due to fallback during training.
SW-A1 No. 3 Footer print
TX
When set to "1", the date of reception, the sender machine No., and the
page No. are automatically recorded at the end of reception.
RX
CED
T
SW-A1 No. 4 Length limitation of copy/send/receive
Used to set the maximum page length.
DIS
To avoid possible paper jam, the page length is normally limited to 1
meter for copy or transmit, and 1.5 meters for receive.
SW-A3 No. 3 MR Coding
It is possible to set it to "No limit" to transmit a long document, such as a
computer print form, etc. (In this case, the receiver must also be set to
no limit.)
MR Coding is enable.
SW-A3 No. 4 ECM mode
Used to determine ECM mode function. Refer to following table.
SW-A1 No. 5 CSI transmission
(CSI TRANSMISSION) is a switch to set whether the machine sends or
does not send the signal (CSI signal) informing its own telephone No. to
the remote fax machine when information is received. When "nonsending"
is set, the telephone No. is not output on the remote transmitting machine if the remote transmitting machine has the function to display or
print the telephone No. of receiving machine, using this CSI signal.
SW-A3 No.4 ECM MODE
0
1
1
SW-A3 No.5 ECM MMR MODE
0
1
0
1
Compression ECM MMR mode
ECM MH mode
method
Yes
No
No
No
Yes
Yes
No
No
Yes
Yes
Yes
Yes
MR Mode
SW-A1 No. 6 DIS receive acknowledgment during G3 transmission
0
(Depending on remote machine)
Used to make a choice of whether reception of DIS (NSF) is acknowledged after receiving two DISs (NSFs) or receiving one DIS (two NSFs).
It may be useful for overseas communication to avoid an echo suppression problem, if set to 1.
SW-A3 No. 5 ECM MMR mode
See SW-A3 No. 4.
SW-A3 No. 6 ~ No. 8 Reserved
SW-A1 No. 7 Non-modulated carrier for V29 transmission modem
Set to "0".
Though transmission of a non-modulated carrier is not required for transmission by the V29 modem according to the CCITT recommendation, it
may be permitted to a send non-modulated carrier before the image
signal to avoid an echo suppression problem. It may be useful for overseas communication to avoid an echo suppression problem, if set to 1.
SW-A4 No. 1 ~ No. 5 Signal transmission level
Used to control the signal transmission level in the range of-0dB to31dB.
SW-A4 No. 6 Protocol monitor (Error print)
SW-A1 No. 8 EOL (End Of Line) detect timer
If set to "1", protocol is printed at communication error.
Used to make a choice of whether to use the 25-second or 13-second
timer for detection of EOL.
This is effective to override communication failures with some facsimile
models that have longer EOL detection.
SW-A4 No. 7 Protocol monitor
Normally set to "0". If set to "1", communication can be checked, in case
of trouble, without using a G3 tester or other tools.
When communication FSK data transmission or reception is made, the
data is taken into the buffer. When communication is finished, the data is
analysed and printed out. When data is received with the line monitor
(SW-A4 No. 8) set to "1" the reception level is also printed out.
SW-A2 No. 1 ~ No. 4 Modem speed
Used to set the initial modem speed. The default is 9600BPS.
It may be necessary to program it to a slower speed when frequent line
fallback is encountered, in order to save the time required for fallback
procedure.
SW-A4 No. 8 Line monitor
Normally set to "0". If set to "1", the transmission speed and the reception level are displayed on the LCD. Used for line tests.
SW-A2 No. 5 Sender’s information transmit
(SENDER’S INFORMATION TRANSMISSION) is a switch to set the
function to print the content of HEADER PRINT described in the passcode
list at the front end of receiver’s original when original is sent to the
remote machine.
SW-A5 No. 1, No. 2 Digital line equalization setting (Reception)
Line equalization when reception is to be set according to the line characteristics.
If this switch is set to "NO", the HEADER PRINT is not output at the
receiving machine.
Setting should be made according to distance between the telephone
and the telephone company central switching station.
SW-A2 No. 6 Reserved
SW-A5 No. 3, No. 4 Digital line equalization setting (Transmission)
Set to "0".
Line equalization when transmitter is to be set according to the line
characteristics.
Setting should be made according to distance between the telephone
and the telephone company central switching station.
SW-A2 No. 7 Communication error treatment in RTN sending mode
(Reception)
Used to determine communication error treatment when RTN is sent by
occurrence of a received image error in G3 reception. When it is set to
"1", communication error is judged as no error.
2 – 13
UX-510UA
FO-1470U
SW-A5 No. 5, No. 6 Digital cable equalizer setting
(Reception for Caller ID)
SW-B2 No. 7, No. 8 Reserved
Set to "0".
Line equalization when reception for CALLER ID is to be set according
to the line characteristics.
Setting should be made according to distance between the telephone
and the telephone company central switching station.
SW-B3 No. 1 ~ No. 5 Reserved
Set to "0".
SW-A5 No. 7 Error criterion
SW-B3 No. 6, No. 7 Auto dial mode Delay timer of before line connect
Used to select error criterion for sending back RTN when receiving image data.
Delay time between the dial key input and line connection under the
auto dial mode.
RAPID01
SW-A5 No. 8 Anti junk fax check
CML RELAY ON
When using the Anti junk fax function, set to "1".
DIALLING
SW-A6 No. 1 Auto gain control (MODEM)
When this mode is enabled, if the reception signal level is under 31dBm,
the modem itself controls the signal gain automatically.
SW-A6 No. 2 End buzzer
Setting this bit to 0 will disable the end buzzer (including the error buzzer/
on-hook buzzer).
No.6
No.7
0
0
1
1
0
1
0
1
0sec
1.5sec
3.0sec
4.5sec
SW-B3 No. 8 Hold key
Used to set YES/NO of holding function by the HOLD key.
SW-A6 No. 3 Disconnect the line when DIS is received in RX mode
SW-B4 No. 1, No. 2 Auto dial mode Delay timer of after line connect
Bit1= 0: When DIS signal is received during RX mode, the line is disconnected immediately.
Delay time between the line connection and dial data output under the
auto dial mode.
Bit1= 1: When DIS signal is received during RX mode, the line is disconnected on the next tone.
DIAL DATA
RAPID01
CML RELAY ON
SW-A6 No. 4 Equalizer freeze control (MODEM)
This switch is used to perform reception operation by fixing the equalizer control of modem for the line which is always in an unfavorable state
and picture cannot be received.
* Usually, the control is executed according to the state of line where
the equalizer setting is changed always.
No.1
No.2
0
0
1
1
0
1
0
1
1.7sec
3.0sec
3.6sec
4.0sec
SW-A6 No. 5 Equalizer freeze control 7200BPS only
Setting which specifies SW-A3 No. 6 control only in the condition of
7200BPS modem speed.
SW-B4 No. 3 Dial mode
SW-A6 No. 6 CNG transmission in manual TX mode
SW-B4 No. 4 Pulse → Tone change function by
When set to "1", fax transmit the CNG signal in case of manual transmission mode (User press the START key after waiting for the fax answering signal from handset or speaker).
When setting to 1, the mode is changed by pressing the
pulse dial mode to the tone dial mode.
SW-A6 No. 7 Reserved
When using the 33% make ratio pulse dial, set to "0".
When using the 40% make ratio pulse dial, set to "1".
When using the pulse dial, set to 1. When using the tone dial, set to 0.
key
key from the
SW-B4 No. 5 Dial pulse make/break ratio (%)
Set to "0".
SW-B4 No. 6, No. 7 Reserved
SW-A6 No. 8 Modem speed automatic fallback when RX level is
under -40dBm
Set to "0".
When set to "1", if fax signal level is under -40dBm during reception,
machine selects the slower modem speed automatically.
It is effective when noises occur on the received document due to the
long distance communications.
SW-B4 No. 8 Recalling fixed only one time when dialing was unsuccessful without detecting busy tone signal
When dialing results in failure since the busy tone cannot be detected,
recalling is fixed to one time.
SW-B1 No. 1 ~ No. 4 Recall interval
Choice is made for a redial interval for speed and rapid dial calls.
Use a binary number to program this. If set to 0 accidentally, 1 will be
assumed.
Supplementary explanation
If time-out termination is made when dialing, only single recall is possible even if the setting time of recalls (SW-B1 No. 5 - No. 8) has been set
to some times. This soft switch is added in order to meet FCC.
SW-B1 No. 5 ~ No. 8 Recall times
SW-B5 No. 1 ~ No. 5 DTMF signal transmission level (Low)
Choice is made as to how many redials there should be.
The transmission level of DTMF signal is adjusted. (lower frequency)
SW-B2 No. 1 Dialing pause (sec/pause)
00000: 0dBm
Pauses can be inserted between telephone numbers of direct dial connection. Selection of 4 sec or 2 sec pause is available.
↓
11111: -15.5dBm (-0.5dBm x 31)
SW-B2 No. 2 Dial tone detection (before auto dial)
SW-B5 No. 6 ~ No. 8 Reserved
Used to set YES/NO of dial tone detection in auto dialing.
Set to "0".
SW-B2 No. 3 Reserved
SW-B6 No. 1 ~ No. 5 DTMF signal transmission level (High)
Set to "0".
The transmission level of DTMF signal is adjusted. (higher frequency)
SW-B2 No. 4 Busy tone detection (after auto dial)
00000: 0dBm
Used to set busy tone detection in auto dialing.
↓
SW-B2 No. 5, No. 6 Waiting time after dialing
11111: -15.5 dBm (-0.5dBm x 31)
This is time waiting for the opponent’s signals after dialing.
2 – 14
UX-510UA
FO-1470U
SW-B6 No. 6 Dial tone detection (LCR center call)
<Example of use>
Used to set YES/NO of dial tone detection (calling LCR center).
Phone Number
Intended
Purpose
SW-B6 No. 7, No. 8 Reserved
Ring Pattern
Set to "0".
SW-C1 No. 1, No. 2 Reading slice (Binary)
Used to determine the set value of reading density in standard/fine mode.
The standard setting is "00" (Factory setting is "00")
SW-C1 No. 3, No. 4 Reading slice (Half tone)
Ring Pattern
555-1234
Voice Calls
Standard
555-1235
Facsimile Calls
Pattern 1
555-1236
Answering
Machine
Pattern 2
555-1237
PC Modem
Pattern 3
<Distinctive Ringing Timing Specifications>
1) USA
Used to determine the set value of reading density in half tone mode.
The standard setting is "00" (Factory setting is "00")
DISTINCTIVE RING → 1:RING PATTERN 1 → 2:RING PATTERN 2
↑
↓
5:OFF SETTING
← 4:STANDARD RING ← 3:RING PATTERN 3
SW-C1 No. 5 Line density selection
Used to set the transmission mode which is automatically selected when
the Resolution key is not pressed. In the copy mode, however, the fine
mode is automatically selected unless the Resolution key is manually
set to another mode.
2) Canada
DISTINCTIVE RING → 1:RING PATTERN 1 → 2:RING PATTERN 2
↑
↓
7:OFF SETTING
3:RING PATTERN 3
↑
↓
6:STANDARD RING ← 5:RING PATTERN 5 ← 4:RING PATTERN 4
SW-C1 No. 6 Reserved
Set to "0".
SW-C1 No. 7 MTF correction in half tone mode
•
This allows selection of MTF correction (dimness correction) in the half
tone mode.
When "NO" (=1) is selected, the whole image becomes soft and mild.
Clearness of characters will be reduced. Normally set to "YES" (=0).
Ring Pattern
STANDARD has 5 ring patterns, and DISTINCTIVE has 9 patterns.
Ring patterns ~ for USA, and ~ for Canada.
However, to make the setting procedure as easy as possible for the
user to understand these patterns are grouped as follows:
<Optional Setting>
1) RING PATTERN 1
RING PATTERN
for USA
RING PATTERN
for USA
RING PATTERN
for Canada
2) RING PATTERN 2
RING PATTERN
for USA
RING PATTERN
for Canada
3) RING PATTERN 3
RING PATTERN
for USA
RING PATTERN
for Canada
4) RING PATTERN 4
RING PATTERN
for Canada
5) RING PATTERN 5
RING PATTERN
for Canada
6) STANDARD RING
7) OFF SETTING
14
SW-C1 No. 8 Reserved
59
1
4
5
2
6
3
7
8
9
Set to "0".
SW-D1 No. 1 ~ No. 4 Number of rings for auto receive
When the machine is set in the auto receive mode, the number of rings
before answering can be selected. It may be set from one to four rings
using a binary number. Since the facsimile telephone could be used as
an ordinary telephone if the handset is taken off the hook, it should be
programmed to the user’s choice. If the soft switch was set to 1, direct
connection is made to the facsimile. If a facsimile calling beep was heard
when the handset is taken off the hook, press the START key and put
the handset on the hook to have the facsimile start receiving. If it was set
to 0 accidentally, receive ring is set to 1.
NOTE: If the machine is set to answer after a large number of rings, it
may not be able to receive faxes successfully. If you have difficulty receiving faxes, reduce the number of rings to a maximum
of 6.
2S ring
STANDARD
SW-D1 No. 5 Automatic switching manual to auto receive mode
4S ring
2S ring
2S ring
This soft switch is used to select whether the machine should switch to
the auto receive mode after 5 rings in the manual receive mode or remain in the same way as SW-D1 No. 1, No. 2, No. 3 and No. 4 "0"1"0"1"(5
rings).
1.5S ring
3S ring
1S ring
4S ring
SW-D1 No. 6 Reserved
0.5S
1.5S ring
Set to "0".
0.5S
RING
PATTERN 1
for USA
SW-D1 No. 7, No. 8 CI detect frequency
Detection frequency of ring signal for auto reception is set.
When set to No. 6=0, No. 7=0, frequency is set to PTT recommendation.
When set to No. 6=0, No. 7=1, frequency is set to 11.5Hz or more.
When set to No. 6=1, No. 7=0, frequency is set to 13.0Hz or more.
When set to No. 6=1, No. 7=1, frequency is set to 20.0Hz or more.
RING
PATTERN 2
for USA
RING
PATTERN 3
for USA
RING
PATTERN 4
for USA
SW-D2 No. 1 ~ No. 3 Distinctive ringing setting (PATTERN 4 and 5
are for CANADA only)
RING
PATTERN 5
for CANADA
This function allows reception of services offered by USA and Canada
telephone companies in which the customer contracts with the telephone
company to have up to 4 telephone numbers (USA) or 6 telephone numbers (Canada) established for one line.
Each telephone number is signalled by a different ringing pattern, and
the customer can allocate each number to a specific use.
RING
PATTERN 6
for CANADA
RING
PATTERN 7
for CANADA
RING
PATTERN 8
for CANADA
RING
PATTERN 9
for CANADA
4S ring
0.8S
0.8S
0.4S
1S
0.3S
0.2S
4S ring
0.3S
0.2S
4S ring
0.4S 0.4S 0.8S
0.2S 0.2S
1S
4S ring
1S
4S ring
1S
1S
1S
0.5S
0.5S
1S
0.5S
0.5S
0.5S
0.5S
0.5S
0.5S
1S
0.5S
0.25S 0.25S 0.25S
0.2S 0.2S
0.25S 0.25S
0.2S
6S
2 – 15
UX-510UA
FO-1470U
SW-D2 No. 4 Reserved
SW-F1 No. 5 ~ No. 8 Remote operation code figure by external TEL
(0 ~ 9)
Set to "0".
Used for Caller ID function.
Remote operation codes can be changed from 0 through 9. If set to
greater than 9, it defaults to 9. The "5
" is not changed.
Ex-7
(Default: 5
)
SW-D2 No. 6 Caller ID detect during CI off
SW-F2 No. 1 CNG detection in STAND-BY mode
Detection of caller ID signal is performed as follows:
0:First CI OFF only
1:All of CI OFF
When setting to "1", the CNG signal detection function during standby
stops.
SW-D2 No. 7, No. 8 Reserved
Used for detection of CNG in 1 to 4 pulses.
SW-D2 No. 5 Caller ID function
SW-F2 No. 2, No. 3 Number of CNG detect (AM mode)
Set to "0".
SW-F2 No. 4, No. 5 Number of CNG detect (STAND-BY mode)
SW-D3 No. 1 ~ No. 5 CI off detection timer (0-1550ms setting by
50ms step)
Used for detection of CNG in 1 to 4 pulses.
Set the minimum time period of CI signal interruption which affords to be
judged as a CI OFF section with 50ms steps.
(Example)
SW-F2 No. 6 ~ No. 8 Reserved
A
Set to "0".
SW-G1 No. 1 ~ No. 4 Quiet detect time
B
400msec
1
When an answering machine is connected, if a no sound state is detected for a certain period of time, the machine judges it as a transmission from a facsimile machine and automatically switches to the FAX
mode.
2000msec
2
SW-G1 No. 5 ~ No. 8 Quiet detect start timing
01110 (50ms ~ 14):
700ms (CI interruption>700ms:Judged as a CI OFF section)
The section 1 is not judged as a CI OFF section, the CI signal A
is counted as one signal.
The section 2 is judged as a CI OFF section, the CI signal B is
considered as the second signal.
00111 (50ms ~ 7):
350ms (CI interruption>350ms:Judged as a CI OFF section)
The section 1 is judged as a CI OFF section, and the CI signal A
is counted as two signals.
The section 2 is judged as a CI OFF section, and the CI signal B
is considered as the third signal.
Inserts a pause before commencing quiet detection.
SW-D3 No. 6 ~ No. 8 Reserved
The switch which sets the time from the start of detection function to the
end of the function.
SW-G2 No. 1 ~ No. 8 Reserved
Set to "0".
SW-G3 No. 1, No. 2 OGM detect timer
This is used to change the OGM detection time for answering machine
hook up detection.
SW-G3 No. 3, No. 4 Reserved
Set to "0".
SW-G3 No. 5, No. 6 Selection time of quiet detection
Set to "0".
SW-G3 No. 7 Choice after quiet detect
SW-E1 No. 1 ~ No. 8 Reserved
Set to "0".
"0": The reception begins when no sound is detected in A.M. mode.
SW-E2 No. 1 ~ No. 8 Reserved
"1": The DIS signal is transmitted only once when no sound is detected
in A.M. mode.
Set to "0".
SW-G3 No. 8 Reserved
SW-E3 No. 1 ~ No. 8 Reserved
Set to "0".
Set to "0".
SW-F1 No. 1, No. 2 DTMF detect time
SW-H1 No. 1, No. 2 Busy tone detection ON/OFF time (Lower duration)
Used to set detect time of DTMF (Dual Tone Multi Frequency) used in
remote reception (5
).
The initial value of detection is set according to electric condition.
The set value is changed according to the local switch board. (Erroneous detection of sound is reduced.)
The longer the detect time is, the less the error detection is caused by
noises.
Normally the upper limit is set to 900msec, and the lower limit to 200msec.
SW-F1 No. 3 Protection of remote reception (5
Used to set the function of remote reception (5
the remote reception function is disabled.
) detect
If erroneous detection is caused by sound, etc., adjust the detection
range.
). When set to "1",
The lower limit can be set in the range of 350msec to 150msec.
SW-F1 No. 4 Remote reception with GE telephone
(Corresponding to TEL made by GE) P. B. X.
"1": Compatible with TEL mode by GE
"0": Not compatible
•
When sending (5
) for remote reception with a GE manufactured
telephone remote reception may not take place because of special
specifications in their DTMF.
To overcome this, a soft SW is provided to change the modem setting to allow for remote reception.
•
If this soft SW is set to "1", other telephone sets may be adversely
affected.
2 – 16
UX-510UA
FO-1470U
SW-H1 No. 3, No. 4 Busy tone detection ON/OFF time (Upper duration)
SW-I7 No. 1 ~ No. 8 Reserved
Set to "0".
Similarly to SW-H1 No. 1, the set value can be varied.
SW-J1 No. 1 Activity report print
The upper limit can be set in the range of 650msec to 2700msec.
This soft switch is used to select: whether or not to print out the activity
report when the memory is full. An activity report can be printed when
the following key entry command is made.
SW-H1
SW-H1
SW-H1
SW-H1
No. 1
No. 2
No. 3
No. 4
0
0
0
0
150msec ~ 650msec
0
0
0
1
150msec ~ 900msec
0
0
1
0
150msec ~ 1500msec
0
0
1
1
150msec ~ 2700msec
When the switch function is set to "0" (no), the data in the memory will
be deleted from the oldest as it reaches the maximum memory capacity.
0
1
0
0
200msec ~ 650msec
SW-J1 No. 2 Total communication hours and pages print
0
1
0
1
200msec ~ 900msec
0
1
1
0
200msec ~ 1500msec
Used to make a choice of whether the total communication time and
pages are recorded in the activity report.
0
1
1
1
200msec ~ 2700msec
1
0
0
0
250msec ~ 650msec
1
0
0
1
250msec ~ 900msec
Used to make a choice of whether the registered sender’s phone number
can be changed or not. If the switch is set to "1", new registration of the
sender’s phone number is disabled to prevent accidental wrong input.
1
0
1
0
250msec ~ 1500msec
SW-J1 No. 4, No. 5 Reserved
1
0
1
1
250msec ~ 2700msec
Set to "0".
1
1
0
0
350msec ~ 650msec
SW-J1 No. 6 Summer time setting
1
1
0
1
350msec ~ 900msec
1
1
1
0
350msec ~ 1500msec
This is used to set YES/NO of automatic clock adjustment for European
Summer time.
1
1
1
1
350msec ~ 2700msec
Detection range
"FUNCTION", "2", "#", "START"
After producing the activity report, all the data in the memory will be
cleared.
SW-J1 No. 3 Sender’s phone number setting
SW-J1 No. 7, No. 8 Ringer volume
Used to adjust ringing volume.
SW-H1 No. 5 Reserved
SW-J2 No. 1, No. 2 Speaker volume (3 stages)
Set to "0".
Used to adjust sound volume from a speaker.
SW-H1 No. 6 Busy tone detect continuation sound detect
(during ICM: for internal A.M.)
SW-J2 No. 3 Polling key
If this switch is set to 1, the last of Rapid key works as polling key.
Used to select detection of the continuous sound of certain frequency.
SW-J2 No. 4, No. 5 Handset receiver volume
SW-H1 No. 7 Reserved
Used to adjust sound volume from a handset receiver volume.
Set to "0".
SW-J2 No. 6 ~ No. 8 Reserved
SW-H1 No. 8 Busy tone detect intermittent sound detect
(during ICM: for internal A.M.)
Set to "0".
Used to select detection of the intermittent sound of certain frequency.
SW-J3 No. 1 Automatic cover sheet
SW-H2 No. 1, No. 2 Busy tone detection pulse number
The machine automatically generates a cover sheet and sends it as the
last page of each transmission.
Used to set detection of Busy tone intermittent sounds.
SW-J3 No. 2 ~ No. 4 Communication result printout (Transaction
report)
SW-H2 No. 3 Fax switching when A.M. full
If the answering machine’s memory (tape) is full and there is no response, the machine automatically switches to Fax reception.
Every communication, the result can be output. As usual, it is set to print
the timer sending communication error alone. If No. 2: 0 No. 3: 1 No. 4: 0
are set, printing is always on (printed even if it is normally ended).
SW-H2 No. 4 ~ No. 7 Reserved
Set to "0".
000: Error, timer and memory sending/receiving
SW-H2 No. 8 Busy tone continuous sound detect time
001: Sending
Set detecting time busy tone continuous sound for 5 or 10 seconds.
010: Continuous printing
SW-I1 No. 1 ~ No. 8 Reserved
011: Not printed
Set to "0".
100: Communication error
SW-I2 No. 1 ~ No. 8 Reserved
SW-J3 No. 5 ~ No. 8 Reserved
Set to "0".
Set to "0".
SW-I3 No. 1 ~ No. 8 Reserved
SW-K1 No. 1 Entering DIAG mode by pressing SPEED key
Set to "0".
A bit which is used in the production process only. When the SPEED key
is pressed, the switch is changed from the stand-by state to the DIAG
mode.
SW-I4 No. 1 ~ No. 8 Reserved
Set to "0".
SW-K1 No. 2 ~ No. 8 Reserved
SW-I5 No. 1 ~ No. 8 Reserved
Set to "0".
Set to "0".
SW-L1 No. 1 ~ No. 4 Reserved
SW-I6 No. 1 ~ No. 8 Reserved
Set to "0".
Set to "0".
2 – 17
UX-510UA
FO-1470U
SW-N3 No. 5, No. 6 Digital egualization setting (Recept for LCR V23
mode)
SW-L1 No. 5 Cut off mode (COPY mode)
Whether the excessive part is printed on the next recording paper or
discarded is selected to copy a document which is longer than the recording paper.
Line egualization when Open LCR table download is to be set according
to the line characteristics.
Setting should be made according to distance between the telephone
and the telephone company central switching station.
SW-L1 No. 6 A4 Paper enable
The use of recording paper of A4 is enabled.
SW-N3 No. 7, No. 8 Reserved
SW-L1 No. 7 LEGAL and LETTER paper enable
Set to "0".
The use of recording paper of LEGAL and LETTER is enabled.
SW-L1 No. 8 2 IN 1 mode
A function to print transmitted data of two pages on one sheet.
SW-L2 No. 1, No. 2 Paper set size
At present size of the recording paper.
SW-L2 No. 3 Automatic reduce of receive
If set to 1, it is reduced automatically when receiving.
SW-L2 No. 4 Print contrast
0: Normal
1: Light
SW-L2 No. 5 Reception reduction ratio in case of memory full
This model is designed so that the print is started according to the setting of SW-L2 No.3 when reception of one page is completed. However,
if the memory is filled with data before completion of reception of one
page, the print is started with the reduction ratio which is set with this
switch.
SW-L2 No. 6 ~ No. 8 Reserved
Set to "0".
SW-M1 No. 1 ~ No. 8 Reserved
Set to "0".
SW-M2 No. 1 ~ No. 8 Reserved
Set to "0".
SW-N1 No. 1 ~ No. 6 LCR short time
First time setting transmitting to the Open LCR center.
SW-N1 No. 7, No. 8 Reserved
Set to "0".
SW-N2 No. 1 ~ No. 6 LCR long time
Second time setting transmitting to the Open LCR center.
SW-N2 No. 7, No. 8 Reserved
Set to "0".
SW-N3 No. 1 LCR Time Select
Used to select LCR short time or LCR long time.
0:LCR short time is selected.
1:LCR long time is selected.
SW-N3 No. 2 Temporary release of caller ID withhold
Used to do temporary release of caller ID withhold.
0:Normal dialing.
1:Release of caller ID withhold before dialing.
SW-N3 No. 3 Connect Japanese center
Used to connect Japanese open LCR center.
0:Connect USA open LCR center.
1:Connect Japanese open LCR center.
SW-N3 No. 4 Open LCR debug mode
Used to debug open LCR function.
0:Normal mode.
1:debug mode.
2 – 18
UX-510UA
FO-1470U
[3] Troubleshooting
Refer to the following actions to troubleshoot any of the problems mentioned in 1-4.
[1]
A communication error occurs.
[2]
Image distortion produced.
[3]
Unable to do overseas communication.
[4]
Communication speed slow due to FALLBACK.
•
Increase the transmission level SOFT SWITCH A4-1, 2, 3, 4, 5.
May be used in case [1] [2] [3].
•
Decrease the transmission level SOFT SWITCH A4-1, 2, 3, 4,
5. May be used in case [3].
•
Apply line equalization SOFT SWITCH A5-1, 2.
May be used in case [1] [2] [3] [4].
•
Slow down the transmission speed SOFT SWITCH A2-1, 2, 3,
4. May be used in case [2] [3].
•
Replace the TEL/LIU PWB.
May be used in all cases.
•
Replace the control PWB.
May be used in all cases.
* If transmission problems still exist on the machine, use the following
format and check the related matters.
TO:
ATT:
Ref.No. :
CC:
ATT:
Date
:
Dept
:
Sign
:
FM:
From: Mr.
Our customer
Other party
Problem mode
Name
Address
Contact person
Name
Address
Contact person
Line: Domestic / international
Reception / Transmission
Frequency:
Confirmation
item
Ref.No.:
***** Facsimile communication problem *****
Fax Tel No.:
Our customer
Date:
Model:
G3
Automatic reception / Manual reception
Automatic dialing / Manual dialing / Others
% ROM version:
Other party
B1
B2
Tel No.
Fax No.
Model name
Tel No.
Fax No.
Model name
Phase: A, B, C, D.
Please mark problem with an X.
No problem is: 0.
A1 A2 B1 B2 C1 C2
A1
A2
C1
D2
C2
E1
E2
Our service
D1
Other party's service
Comment
Countermeasure
**** Please attach the G3 data and activity report on problem. ****
* Please complete this report before calling the “TAC” hotline if problem still occurs.
2 – 19
D1 D2 E1 E2
Transmission level setting is (
customer
Transmission level (
) dBm
Reception level (
) dBm
By level meter at B1 and B2
) dB at our
UX-510UA
FO-1470U
[4] Error code table
1. Communication error code table
G3 Transmission
Code
Final received signal
Error Condition (Receiver side)
0
Incomplete signal frame
Cannot recognize bit stream after flag
1
NSF, DIS
Cannot recognize DCS signal by echo etc.
2
CFR
Disconnects line during reception (carrier missing etc)
3
FTT
Disconnects line by fall back
4
MCF
Cannot recognize NSS signal (FIF code etc)
Disconnects line during reception of multi page
Cannot recognize NSS, DCS signal in the case of mode change
5
PIP or PIN
The line is hung up without replying to telephone request from the receiving party.
6
RTN or RTP
Cannot recognize NSS, DCS signal after transmit RTN or RTP signal.
7
8
No signal or DCN
−
No response in receiver side or DCN signal received* (transmitter side)
Owing to error in some page the error could not be corrected although the specified number of
error retransmissions were attempted.
−
11
Error occurred after or while reception by the remote (receiving) machine was revealed to be
impossible.
12
−
Error occurred just after fallback.
13
−
Error occurred after a response to retransmission end command was received.
G3 Reception
Code
0
1
Final received signal
Incomplete signal frame
NSS, DCS
Error Condition (Receiver side)
Cannot recognize bit stream after flag
Cannot recognize CFR or FTT signal
Disconnects line during transmission (line error)
2
NSC, DTC
Cannot recognize NSS signal (FIF code etc)
3
EOP
Cannot recognize MCF, PIP, PIN, RTN, RTP signal
4
5
EOM
MPS
Cannot recognize MCF, PIP, PIN, RTN, RTP signal in the case of mode change
The line is hung up without replying to communication request.
6
7
PR1-Q
No signal or DCN
Cannot recognize PIP, PIN signal in the case of TALK request
No response in transmitter (cannot recognize DIS signal) or DCN signal received* (receiver side)
8
−
Error occurred upon completion of reception of all pages.
9
−
Error occurred when mode was changed or Transmission/Reception switching was performed.
10
−
Error occurred during partial page or physical page reception.
11
−
Error occurred after or during inquiry from the remote (transmitting) machine as to whether
12
−
Error occurred during or just after fallback.
13
−
Error occurred after the retransmission end command was received.
reception is possible or not.
2 – 20
UX-510UA
FO-1470U
3-2. Automatic document feed
CHAPTER 3. MECHANISM BLOCKS
1) Use of the paper feed roller and separation rubber plate ensures
error-free transport and separation of documents. The plate spring
presses the document to the paper feed roller to assure smooth feeding of the document.
,,,
,
[1] General description
2) Document separation method: Separation rubber plate
1. Document feed block and diagram
Separation rubber
Document
guide upper
Separation
Original
rubber
sensor
Separate
Pinch roller
plate
spring
Front
sensor
Hopper guide
Separate
spring
Paper feed
spring
Paper feed arm
Feed roller 2
Paper feed spring
Paper feed arm
Paper feed roller
Document guide
lower
Fig. 3
3-3. Documents applicable for automatic feed
Paper feed roller
Pinch roller
4x6 series
(788mm x 1091mm x
1000 sheets)
Feed roller
Pinch roller2
Pinch roller spring 2
Minimum
Fig. 1
Feeder capacity
Paper weight
2. Document feed operation
Maximum
Square
meter series
Minimum
Maximum
20 sheets, max.
45kg
64.3kg
52g/m2
74.3g/m2
Paper thickness (ref.) 0.06mm
0.09mm
0.06mm
0.09mm
Paper size
128mm x 148mm ~ (MIN. SIZE)
A4 (210mm x 297mm), Letter (216mm x 279mm)
1) The original, which is set in the document hopper, feeds automatically when the front sensor is activated. This in turn activates the
pulse motor which drives the document supply roller. The document
stops when the lead edge is detected by the document sensor.
NOTE: Double-side coated documents and documents on facsimile recording paper should be inserted manually. The document feed
quantity may be changed according to the document thickness.
2) The lead edge of the original is fed a specified number of pulses after
the lead edge of the document is detected for the reading process to
begin.
Documents corresponding to a paper weight heavier than 64.3kg (74.3g/
m2 ) and lighter than 135kg (157g/m2 ) are acceptable for manual feed.
3) The trailing edge of the original is fed a specific number of pulses
after the trailing edge of the document deactivates the original sensor. The read process then stops and the original is discharged.
Documents heavier than 135kg in terms of the paper weight must be
duplicated on a copier to make it operative in the facsimile.
4) When the front sensor is in the OFF state (any document is not set
up in the hopper guide), the drive will be stopped when the document is discharged.
3-4. Loading the documents
3. Hopper mechanism
2) Place documents face down in the hopper.
1) Make sure that the documents are of suitable size and thickness,
and free from creases, folds, curls, wet glue, wet ink, clips, staples
and pins.
i) Adjust the document guides to the document size.
3-1. General view
ii) Align the top edge of documents and gently place them into the
hopper. The first page under the stack will be taken up by the
feed roller to get ready for transmission.
NOTES: 1) Curled edge of documents, if any, must be straighten
out.
2) Do not load the documents of different sizes and/or
thicknesses together.
Fig. 2
The hopper section contains document guides that are used to adjust
the hopper to the width of the original document. This ensures that the
original feeds straight into the fax machine for scanning.
Document width: 148 mm to 216 mm (A5 longitudinal size to Letter
longitudinal size)
NOTE: Adjust the document guide after setting up the document.
3–1
,,
,
,
UX-510UA
FO-1470U
5. Optical system
Paper feed spring
Separation
rubber
Last page of document
(1) General view
Rear sheet
CCD PWB
Document
Red mark
LED lamp
First page of
document
Paper feed arm
Reader
glass
Mirror 2
Paper feed roller
Fig. 4
Mirror 3
CCD
Lens
Mirror 1
Fig. 5
3-5. Documents requiring use of copy
1) Documents smaller than 128mm x 148mm.
(2) Composition
2) Documents thinner than the thickness of 0.06mm.
3) Documents containing creases, folds, or curls, especially those whose
surface is curled (maximum allowable curl is 5mm).
The optical system is composed of the document feed mechanism, the
LED lamp, the reflecting mirrors, the focusing lens, the CCD sensor, and
the read process circuit.
4) Documents containing tears.
5-1. LED Lamp/Lens
5) Carbon-backed documents. (Insert a white sheet of paper between
the carbon back and the document carrier to avoid transfer of carbon
to the carrier.)
The LED lamp is used to project light to the document.
NOTE: Take care for the position of the red mark on the lens. (Top of
the light-projected side)
6) Documents containing an easily separable writing material (e.g., those
written with a lead pencil).
5-2. CCD
The CCD (charge coupled device) image sensor consists of a photodiode
array which converts the intensity of light reflected from the document
surface into series of analog voltages which are then stored in an ana
log shift register. The series of analog voltages are then converted into a
digital equivalent by a black/white binary logic circuit.
7) Transparent documents.
8) Folded or glued documents.
(Example) Scan signal output waveform
4. Document release
Peak
4-1. General
To correct a jammed document or to clean the document running surface, pull the operation panel lock lever under the front center of the
operation panel. To open the upper document guide, the operation panel
must be opened first.
100%
50%
minimum
Maximum document width, 216mm
Scan line
length
Fig. 6
1) The minimum output from the CCD at the maximum scan width of
document (216mm) must be more than 50% of the peak value.
2) The peak output must be about 0.2 ~ 0.6 under room temperature to
avoid CCD saturation.
3–2
UX-510UA
FO-1470U
6. Recording block
(1) General view
Take-up
side
Imaging film
Platen
roller
Pinch
roller
Guide shaft
Thermal
head
Paper guide
PO roller
U turn guide
Supply
side
RP hopper
Rotation plate
Main frame
PU roller
Separate plate
Film sensor
lever
P-IN sensor lever
Fig. 7
6-1. Driving
3) Recording paper transfer sequence
In the drive mechanism, the rotating force of the pulse motor for both
transmission and reception is transmitted to the paper supply roller, the
recording paper feed roller and imaging film drive gear through the pulse
motor axle gear, reduction gear and planetary gear.
a) The recording paper stored in the RP hopper is fed with the PU roller,
and the recording paper is stopped when the P-IN sensor is turned
on by sensing its lead edge.
b) Hereafter, the imaging film and recording paper are transferred with
the recording paper feed roller, and thermal transcription is done on
the recording paper.
6-2. Recording
This equipment employs the thermal transcription system which used
the thermal head imaging film.
c) After thermal transcription, the imaging film is taken up by the roller
on the take-up side, and the recording paper is discharged by the PO
roller.
1) Thermal head
The thermal head is composed of 2,016 heating elements in traverse
line, and the resolution power is 8 dots/mm. The maximum speed is 10
ms/line.
As basic, the density unevenness mainly results from the longitudinal misalignment of the thermal head to the heater line. Other-wise,
the head is in uneven contact with the recording paper feed roller, or
the imaging film is wrinkled.
2) Structure of recording mechanism
1 Are the power and signal cables of the thermal head suitably treated?
2 Does the same symptom appear even if the thermal head pres-sure
The following items are described as the simplified checking method.
Recording is achieved by applying a suitable pressure to the thermal
head through the imaging film of the recording paper feed roller and the
recording paper.
The main scanning is electronically done, and the sub-scanning is me
chanically done (by sending the recording paper with the recording paper feed roller).
spring is replaced?
3 Is the feed roller of the recording paper concentric? (Density is uneven at intervals.)
4 Does the same symptom appear even if the thermal head is replaced?
5 Is the imaging film stained or wrinkled?
3–3
UX-510UA
FO-1470U
[2] Disassembly and assembly procedures
•
This chapter mainly describes the disassembly procedures. For the assembly procedures, reverse the disassembly procedures.
•
Easy and simple disassembly/assembly procedures of some parts and units are omitted. For disassembly and assembly of such parts and units,
refer to the Parts List.
•
The numbers in the illustration, the parts list and the flowchart in a same section are common to each other.
•
To assure reliability of the product, the disassembly and the assembly procedures should be performed carefully and deliberately.
1
Parts list (Fig. 1)
Operation panel unit, document guide
lower and rear cover
No.
1
2
9
3
10
4
11
5
12
6
13
7
14
8
15
16
Q’ty
No.
1
Mechanism unit
Part name
1
9
Hook switch lever
Part name
Q’ty
1
2
Operation panel unit
1
10
Document guide lower unit
1
3
Screw (3×12)
2
11
Transfer gear
1
4
Side cover
1
12
Transfer bearing
3
5
Screw (3×12)
1
13
Transfer roller
1
6
Screw (3×10)
2
14
Feed gear ass’y
1
7
Rear cabinet
1
15
Paper feed roller
1
8
Screw (3×10)
4
16
Document guide lower
1
2
9
8
3
3
8
4
10
5
8
6
6
10
7
Hook the three lock nail
to LOWER CABINET.
1
15
14
12
12
15
13
16
Rib
14
11
12
Fig. 1
3–4
An attachment rib is attached
in accordance with hole.
UX-510UA
FO-1470U
2
Parts list (Fig. 2)
Document guide upper
No.
Q’ty
No.
1
Operation panel unit
Part name
1
10
Transfer bearing
2
2
Screw (3×10)
2
11
Transfer roller
1
3
Document guide upper
1
12
Separate spring
1
13
Separate plate
1
unit
1
12
3
13
4
14
5
15
6
4
17
8
18
9
19
10
20
1
14
Paper feed arm
2
Panel lock lever
1
15
Paper feed spring
1
6
Idler gear (28Z)
1
16
Separation rubber
1
7
Idler gear (20Z)
1
17
Pinch roller spring
2
8
Transfer gear 2
1
18
Pinch roller shaft
1
9
Rear sheet
1
19
Pinch roller
2
20
Document guide upper
1
13
17
13
18
12
19
16
7
Panel lock lever spring
5
17
5
16
14
15 14
4
20
11
6
5
8
7
10
11
9
10
2
2
3
Positioning rib
3
Hook
1
A hook of a document
guide upper is fit to
positioning rib of panel
unit .
1
Fig. 2
3–5
Q’ty
4
After mounting to the
12
fulcrum and push down
to the direction of arrow
mark.
20
20
2
Part name
UX-510UA
FO-1470U
3
Parts list (Fig. 3)
Operation panel
No.
rib
Panel PWB
Part name
Q’ty
1
Operation panel unit
1
2
Screw (2.6×6)
5
3
Insulation sheet
1
4
Operation panel PWB unit
1
5
12 key
1
6
Start key
1
7
Stop key
1
8
Mode key
1
9
Direct key
1
10
Panel cable
1
11
Operation panel
1
2
3
Note) Keep the panel PWB
to under the rib like a
picture.
1
2
2
2
7
3
8
4
9
5
10
6
11
4
10
1
5
8
Ass'y process
a
b
b
Rib
7
a
6
9
LCD PWB
Note) The LCD PWB should be securely
locked by the click of the panel
case.
11
Fig. 3
3–6
UX-510UA
FO-1470U
4
Parts list (Fig. 4)
Top cover and head frame unit
No.
1
Part name
Q’ty
1
Mechanism unit
1
2
Top cover unit
1
3
Screw (3×10)
5
4
Head frame unit
1
5
Hopper guide, right
1
6
Hopper guide, left
1
7
Screw (3×6)
1
8
Pinion gear
1
9
Hopper spring
1
10
Top cover
1
Confirm of HOPPER GUIDE position.
2
6
3
7
4
8
5
9
GAP 0
Rib
HOPPER GUIDE,
LEFT
6
HOPPER GUIDE,
RIGHT
Rib
GAP 0
10
8
9
5
7
10
3
HEAD CABLE
HEAD
EARTH
CABLE
TEL/LIU
PWB
2
3
3
4
CONTROL
PWB
POWER
SUPPLY
PWB
1
Fig. 4
3–7
UX-510UA
FO-1470U
5
Parts list (Fig. 5)
Head frame and thermal head
No.
1
4
6
15
2
5
7
16
8
17
9
18
10
19
11
20
3
Part name
Q’ty
No.
Part name
Release knob
1
11
Head spring 2
2
Lock spring
1
12
Head spring 1
1
3
Lock lever
1
13
Head frame
1
4
Screw (3×10)
1
14
Head cable
1
5
Pop up spring
1
15
Screw (3×6)
1
6
Cut washer
2
16
Head earth cable
1
7
Film guide shaft
2
17
Head guide, right
1
8
Head guide sheet
1
18
Screw (3×6)
1
9
Thermal head unit
1
19
Head guide, left
1
10
Head spring B
2
20
Thermal head
1
1
13
3
6
2
12
11
13
10
14
12
11
5
10
9
4
8
7
7
18
15
19
16
20
Fix position of
EARTH CABLE.
16
17
17
14
Fig. 5
3–8
Q’ty
1
2
UX-510UA
FO-1470U
6
Parts list (Fig. 6)
Paper out guide
No.
Part name
Q’ty
1
Mechanism unit
1
2
Screw (3×10)
2
3
Paper out guide unit
1
4
Idler gear A
1
5
Take-up gear
1
6
Slip gear ass’y
1
7
Cut washer
1
8
Film shaft C
1
9
PO pinch roller spring
2
10
PO pinch roller
2
11
Paper out guide
1
1
2
9
3
10
4
5
9
10
6
7
8
2
9
10
7
11
3
9
4
10
11
8
5
6
1
Fig. 6
3–9
2
UX-510UA
FO-1470U
Parts list (Fig. 7)
Recording paper hopper, speaker and
pinch roller
7
No.
1
2
14
18
3
15
19
4
16
20
5
17
21
6
Q’ty
No.
1
Mechanism unit
Part name
1
12
Cassette spring
Part name
Q’ty
2
2
Screw (3×12)
2
13
RP hopper
1
3
RP hopper unit
1
14
Screw
2
4
Paper guide
1
15
Screw (3×10)
1
5
Screw
2
16
Speaker holder spring
1
6
RP release spring
1
17
Speaker
1
7
RP release gear, right
1
18
Pinch roller spring
2
8
RP release gear, left
1
19
Pinch roller
2
9
RP release plate
1
20
Document kick plate
1
10
Paper up plate
1
21
Document kick roller
1
11
RP pad
1
22
Pinch roller shaft
1
10
4
9
11
22
7
12
2
8
5
9
3
10
9
11
8
5
12
13
2
7
13
7 , 8
6
14
15
17
16
18
19
20
1
22
18
21
20
19
OK
OK
Position of pinch
shaft,roller,spring
Fig. 7
3 – 10
18
UX-510UA
FO-1470U
Parts list (Fig. 8)
Main frame unit, ROM cover, memory
cover, drive unit and optical unit
8
No.
Q’ty
1
Mechanism unit
1
2
Screw (3×10)
1
3
ROM cover
1
4
Memory cover
1
5
Screw (3×10)
1
6
Drive unit
1
7
Screw (3×10)
3
8
Main frame unit
1
9
Optical unit
1
2
1
2
Part name
4
3
4
3
7
8
5
9
6
7
7
8
5
6
9
1
Fig. 8
3 – 11
UX-510UA
FO-1470U
9
Main frame, U turn guide and transfer roller etc.
Parts list (Fig. 9)
No.
Q’ty
No.
Q’ty
No.
1
Reduction gear A
Part name
1
11
PU roller ass’y
Part name
1
22
Slip spring
Part name
2
PU gear
1
12
PO roller ass’y
1
23
Hold down plate B
1
3
Platen bearing
1
13
U turn guide
1
24
Back tension stopper
1
4
Platen gear
1
14
Sensor lever spring
1
25
Separate plate spring
1
5
Platen bearing
1
15
Film sensor lever
1
26
Separate sheet
1
6
Platen roller
1
16
Sensor lever spring
1
27
Separate plate sheet
1
7
PO gear
1
17
P-IN sensor lever
1
28
Separate plate
1
8
Screw (3×10)
4
18
Pop up spring
1
29
Guide sheet, left
1
9
Film guide shaft B
1
19
Cover switch lever
1
30
Guide sheet, right
1
10
PU roller shaft
1
20
Back tension gear
1
31
PO gear cushion
1
21
Back tension felt
1
32
Main frame
1
1
5
6
8
4
3
12
8
7
31
8
26
13
27
11
19
28
10
21
25
20
29
9
18
30
24
1
10 12 14 18 20 29
2
11 13 15 19 21 30
23
32
22
3
25 16
22 32
4
26 17
23
5
27
24
6
28
OK
7
16
NG
1
17
15
2
14
Position of SENSOR LEVER and SPRING.
31
17
8
15
9
16
Fig. 9
3 – 12
14
Q’ty
UX-510UA
FO-1470U
10
Parts list (Fig. 10)
Drive unit frame
No.
Q’ty
No.
1
Drive unit
Part name
1
10
Planet lever A ass’y
Part name
Q’ty
2
Reduction gear B
1
11
Reduction gear C
2
3
Planet lever B ass’y
1
12
Cam switch ass’y
1
4
Idler gear A
1
13
Screw (3×10)
2
5
Idler gear C
1
14
Motor
1
6
Reduction gear A
1
15
Motor heat sink
1
7
Planet lever C ass’y
1
16
Cushion
1
8
Cam hold spring
1
17
Band
2
9
Cam A
1
18
Drive unit frame
1
1
1
13
2
9
3
10
4
11
5
12
6
13
7
14
8
15
14
15
2
16
7
12
5
18
4
8
16
3
6
17
10
18
11
11
9
5
17
9
Cut after insert must be
touch to the bottom.
8
1
Fig. 10
3 – 13
UX-510UA
FO-1470U
11
Parts list (Fig. 11)
Optical frame
No.
1
4
7
10
3
5
8
11
6
9
12
No.
Optical unit
Part name
1
7
Reader glass
1
2
Screw
2
8
LED
1
3
CCD PWB unit
1
9
Shading sheet 3
2
4
Shading sheet
1
10
Mirror 3
1
5
Lens holding spring
1
11
Mirror 1
1
6
Lens
1
12
Mirror 2
1
13
Optical frame
1
7
9
2
Q’ty
1
Part name
Q’ty
4
5
8
Red( )
9
6
2
Blue
( )
13
3
10
13
11
12
Face of reflect
1
Fig. 11
3 – 14
UX-510UA
FO-1470U
12
Parts list (Fig. 12)
PWB section
No.
Q’ty
No.
1
Mechanism unit
Part name
1
7
Connector
2
Screw (3×6)
1
8
Control PWB unit
1
3
TEL/LIU ARG cable
1
9
TEL/LIU PWB unit
1
4
Screw (4×6)
1
10
Power supply PWB unit
1
5
AC cord
1
11
Earth plate
1
6
Screw (3×10)
6
12
Jack sheet
1
1
2
3
2
6
8
9
5
10
6
11
7
5
6
8
9
3
6
6
7
12
Hook
6
PWB
11
12
Note) The PWB hook to
cabinet.
1
Fig. 12
3 – 15
10
Q’ty
2
4
6
7
4
Part name
UX-510UA
FO-1470U
13
Parts list (Fig. 13)
Wire treatment
No.
Part name
1
Band (Black)
CCD cable
LED cable
Q’ty
1
No.
Part name
4
Screw (4×6)
2
Core (F2125)
2
5
Screw (3×10)
2
3
Screw (3×6)
1
6
Band (100mm)
5
2
Rib
LED
cable
Cam switch
,
Rib
Panel cable
Document guide lower
Cam switch
cable
1
Motor cable
Speaker
LED
cable
cable
Cam switch
cable
Control PWB
Document guide upper rib
Panel cable
Panel PWB
Motor
cable
Key
Panel rib
Rib
Panel cable
Panel cable
Head earth
cable
Earth plate
5
CCD
cable
3
4
AC cord
earth cable
AC cord
Lower
cabinet
Rib
2
The CCD and LED cables
pass to the core 3 times.
ARG cable
TEL/LIU
PWB
Head cable
Power supply PWB
Control
PWB
6
Head unit
6
6
Head
earth
cable
Head earth
cable
within 5mm
Head cable
Position of
BINDING
BAND head.
Head cable
6
Top cover
PO guide
6
Head earth cable
Head unit
Wiring position of
head and head earth cable.
Head and Head eart cable
6
2
The head and head
earth cables pass to
the core 3 times.
Fig. 13
3 – 16
Q’ty
1
4–1
EXT.TEL
LINE
HANDSET
SPEAKER
DRAM
4Mbit
SURGE
PROTECT/
FILTER
AMPLIFIER
AMPLIFIER
CML
AMPLIFIER
INTEGRATED ANALOG DEVICE
(20415)
CONTROL PWB UNIT
[1] Block diagram
CI
TRANSFORMER
AMPLIFIER
CLOCK
32.256MHz
BZ
TEL/LIU
PWB UNIT
CLOCK
32.768kHz
VBT
+3.3V
ROM
2Mbit
VOLTAGE
REGULATOR
SRAM
256kbit
+5V
PIO
FILTER
RECTIFIER
DIODE
TRANSFORMER
RECTIFIER
+24V
DRIVER
CCD
LED
PM
SURGE
ABSORBER
POWER SUPPLY
PWB UNIT
LCD
THERMAL
HEAD
IMAGING
FILM
P-IN
SENSOR
FILM
SENSOR
RECORDING PAPER
OPERATION
PANEL
PANEL
RELAY
STABILIZER
REGULATOR
+5V
PANEL I/F
SIO
SENSOR I/F
RTC
RESET
MOTOR I/F
WATCHDOG
TIMER
THERMAL
HEAD I/F
CCD I/F
TIMER
CPU
INTERRUPT
CONTROLLER
CPU I/F
1CHIP FAX ENGINE (SCE114)
UX-510UA
FO-1470U
CHAPTER 4. DIAGRAMS
SPEAKER
HANDSET
TEL LINE
EXTERNAL LINE
[2] Wiring diagram
CNLIUA
2
TEL/LIU PWB
UNIT
CNHJ
CNLNJ
14
4–2
LED ARRAY
2
CNLED
CNSP
CNLIUA
CCD PWB
7
CNCCD
THERMAL HEAD
16
CNTH
CONTROL PWB UNIT
CNPN
15
TX/RX
MOTOR
2
POWER
SUPPLY
PWB
OPERATION
PANEL PWB
6
CN2
CNPN
CNMT
CNCS
CNPW
6
CNLCD
14
LCD UNIT
CAM SW.
AC CORD
UX-510UA
FO-1470U
UX-510UA
FO-1470U
[3] Point-to-point diagram
CNMT
TX/RX
MOTOR
THERMAL
HEAD
OPERATION
PANEL
PWB
CCD PWB
TPBD
TPAD
TPBD
TPAD
VMT
VMT
VTH
VTH
STRB1
STRB2
THI
N.C.
THG
THG
THG
THVDD
STRB3
STRB4
LATCH
PCLK
DATA
VTH
1
2
3
4
5
6
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
CNPN
1
KEN4A
2
KEN3A
3
KEN2A
4
KEN1A
5
DG
6
DG
7
+5V
ORGSNS 8
9
FRSNS
10
E
11
SEN4
12
SEN3
13
SEN2
14
SEN1
15
SEN0
VO
VCCD
VG
øT
ø2
ø1
øR
1
2
3
4
5
6
7
1
2
3
4
5
6
CNLIUA
1
PE1
TEL OUT 2
3
TEL IN
TEL MUTE 4
5
CI
6
HS
7
CML
8
TXOUT
9
RXIN
10
RHS
DOOR SW 11
12
+5V
13
DG
14
+24VA
TPBD
TPAD
TPBD
TPAD
VMT
VMT
CNTH
1
VTH
2
VTH
3
STRB1
4
STRB2
5
THI
6
N.C.
7
THG
8
THG
9
THG
10 THVDD
11
STRB3
12
STRB4
13
LATCH
14
PCLK
15
DATA
16
VTH
CNPN
1
KEN4A
2
KEN3A
3
KEN2A
4
KEN1A
5
DG
6
DG
7
+5V
8 ORGSNS
9
FRSNS
10
E
11
SEN4
12
SEN3
13
SEN2
14
SEN1
15
SEN0
CNCCD
1
VO
2
VCCD
3
VG
4
øT
5
ø2
6
ø1
7
øR
CNLIUA
1
N.C.
2 TEL OUT
3
TEL IN
4 TEL MUTE
5
CI
6
N.C.
7
CML
8
TXOUT
9
RXIN
10
RHS
11 DOOR SW
12
+5V
13
DG
14
+24V
TEL/LIU
PWB
CNPW
1
+24V
2
+24V
3
MG
4
MG
5
+5V
6
DG
CN2
1
2
3
4
5
6
+24V
+24V
MG
MG
+5V
DG
POWER
SUPPLY
PWB
CNCSW
1
CSW
2
DG
1
2
CSW
DG
CAM
SWITCH
CNSP
1
2
1
2
SP+
SP-
SPEAKER
1
2
+24V
LEDON
LED
SP+
SPCONTROL
PWB
CNLED
1
+24V
2
LEDON
4–3
UX-510UA
FO-1470U
3. Operational description
CHAPTER 5. CIRCUIT DESCRIPTION
Operational descriptions are given below:
•
[1] Circuit description
When a document is loaded in standby mode, the state of the document sensor is sensed via the 1 chip fax engine (SCE114). If the
sensor signal was on, the motor is started to bring the document into
the standby position. With depression of the START key in the offhook state, transmission takes place.
Then, the procedure is sent out from the modem and the motor is
rotated to move the document down to the scan line. In the scan
processor, the signal scanned by the CCD is sent to the internal image processor and the AD converter to convert the analog signal into
binary data. This binary data is transferred from the scan processor
to the image buffer within the RAM and encoded and stored in the
transmit buffer of the RAM. The data is then converted from parallel
to serial form by the modem where the serial data is modulated and
sent onto the line.
1. General description
The compact design of the control PWB is obtained by using CONEXANT
fax engine in the main control section and high density printing of surface mounting parts. Each PWB is independent according to its function
as shown in Fig. 1.
2. PWB configuration
TEL/LIU
PWB
CIS
LCD
PWB
•
CONTROL
PWB
Receive operation
There are two ways of starting reception, manual and automatic.
Depression of the START key in the off-hook mode in the case of
manual receive mode, or CI signal detection by the LIU in the automatic receive mode.
POWER
SUPPLY
PWB
PANEL
PWB
Transmission operation
First, the SCE114 controls the procedure signals from the modem to
be ready to receive data. When the program goes into phase C, the
serial data from the modem is converted to parallel form in the modem interface of the 1 chip fax engine (SCE114) which is stored in
the receive buffer of the RAM. The data in the receive buffer is decoded software-wise to reproduce it as binary image data in the image buffer. The data is DMA transferred to the recording processor
within the SCE114 which is then converted from parallel to serial
form to be sent to the thermal head. The data is printed line by line by
the SCE114 which is assigned to control the motor rotation and strobe
signal.
AC CORD
MOTOR
Fig. 1
1) Control PWB
The control PWB controls peripheral PWBs, mechanical parts, transmission, and performs overall control of the unit.
This machine employs a 1-chip modem (SCE114) which is in-stalled on
the control PWB.
•
Copy operation
To make a copy on this facsimile, the COPY key is pressed when the
machine is in stand-by with a document on the document table and
the telephone set is in the on-hook state.
2) TEL/LIU PWB
First, depression of the COPY key advances the document to the
scan line. Similar to the transmitting operation, the image signal from
the CCD is converted to a binary signal in the DMA mode via the 1
chip fax engine (SCE114) which is then sent to the image buffer of
the RAM. Next, the data is transferred to the recording processor in
the DMA mode to send the image data to the thermal head which is
printed line by line. The copying takes place as the operation is repeated.
This PWB controls connection of the telephone line to the unit.
3) Power supply PWB
This PWB provides voltages of +5V and +24V to the other PWBs.
4) Panel PWB
The panel PWB allows input of the operation keys.
5) LCD PWB
This PWB controls the LCD display.
6) CCD PWB
This PWB controls the pickup optical device.
5–1
UX-510UA
FO-1470U
3) 27L2000 (IC4): pin-32 DIP (ROM)
[2] Circuit description of control PWB
ROM of 2Mbit equipped with software for the main CPU.
1. General description
4) W24258S-70LE (IC8): pin-28 SOP (SRAM)
Fig. 2 shows the functional blocks of the control PWB, which is composed of 5 blocks.
Line memory for the main CPU system RAM area and coding/decoding
process. Used as the transmission buffer.
MAIN CONTROL BLOCK
Memory of recorded data such as daily report and auto dials. When the
power is turned off, this memory is backed up by the lithium battery.
MODEM BLOCK
5) MSM51V4800E (IC5): pin-28 SOJ (DRAM)
(3) ROM
Image memory for recording process.
• Memory for recording pixel data without paper.
(2) INTEGRATED
ANALOG (20415)
(1) SCE114
(4) SRAM (5) DRAM
Fig. 2 Control PWB functional block diagram
2. Description of each block
(1) Main control block
The main control block is composed of CONEXANT 1 chip fax engine
(SCE114), ROM (2Mbit), SRAM (256kbit), DRAM (4Mbit) and Integrated
Analog (20415).
Devices are connected to the bus to control the whole unit.
1) SCE114 (IC9) : pin-176 QFP (FAX CONTROLLER)
2) 20415 (IC13) : pin-32 QFP (INTEGRATED ANALOG)
The FAX ENGINE Integrated Facsimile Controllers.
SCE114, contains an internal 8 bit microprocessor with an external 2
Mbyte address space and dedicated circuitry optimized for facsimile
image processing and facsimile machine control and monitoring.
A[23:0]
D[7:0]
RDN
WRN
CSN[1]/GPO[21]
ROMCSN
CSN[0]
SYNC/GPO[20]
CLKCONFIG[0]/REGDMA/GPO[18]
CLKCONFIG[1]/WAITN/GPO[19]
RASN
CASN[1:0]
DWRN
GPIO[0]/SR4IN
GPO[31]/SR3OUT
IARESET
IACLK/DSPCSN
IA1CLK
SA3IN/DSP1RQN
SR4OUT
SR1IO
SA1CLK
MC24 CPU CONTROL IF
MC24 MEGACALL(8-BIT DATA,24-BIT ADDRESS)
WATCHDOG TIMER
REAL TIME CLOCK
CRYSTAL OSCILLATOR
BATTERY BACK-UP CIRCUIT
INTERRUPT CONTROLLER
BUS INTERFACE
EXTERNAL CPU BUS
GPIO[1]/SASTXD
GPIO[2]/SASRXD
GPIO[3]/SASCLK
GPIO[4]/CPCIN
GPIO[5]/SSCLK2
GPIO[6]/SSTXD2
GPIO[7]/SSRXD2
GPIO[8]/FWRN
GPIO[9]/FRDN
GPIO[10]/SSSTAT2
GPIO[11]/BE/SERINP
GPIO[12]/CS2N
GPIO[13]/CS3N
GPIO[14]/CS4N
GPIO[15]/CS5N
GPIO[16]/IRQ8
GPIO[17]
GPIO[18]/IRQ9N
GPIO[19]/RDY/SEROUT
GPIO[20]/ALTTONE
SM[3:0/GPO[7:4]
PM[3:0/GPO[3:0]
GPIO[37]/IRQ15N
GPIO[36:25]
GPIO[30:26]
CPU BUS
DRAM CONTROL
INTERNAL & EXTERNAL BUS CONTROL
INTERNAL & EXTERNAL DECODE
DMA CONTROLLER
FAX MODEM DSP
CORE (ML 94)
TONE
OPERATOR PANEL IF
32 KEYS
8 LEDS
LCD MODULE
MOTOR POWER
CONTROL
RINGER
SSIF 1
TONE GENERATOR
GENERAL I/O
ALTTONE
GPIO
CALLING PARTY
CONTROL
AUTOBAUD
SYNC-ASYNC SASIF
SSIF 2
FLASH MEMORY IF
SEE
"OPIF
OUTPUTS"
BELOW
INTERNAL CPU BUS
SEE
"OPIF
INPUTS"
BELOW
SCANNER CONTROL & VIDEO PROCESSING
8-BIT PADC
CCD/CIS SCANNER
5 ms,A4/B4 LINES
SHADING CORRECTION(1:1,1:8)
DITHERING
MULTILEVEL B4-A4 REDUCTION
ERROR DIFFUSION
MTF....ETC.
THERMAL PRINTER IF
BI-LEVEL RESOLUTION
CONVERSION
T.4/T.6 CODEC
PROGRAMMABLE
REDUCTION &
EXPANSION
MH,MR,MMR
HARDWARE,ALTEMATE
COMPRESSION &
DECOMPRESSION
5 ms LINE TIME
A4/B4 LINES
TPH ADC
4 STROBE TPH
LATCHLESS TPH
EXTERNAL DMA I/F
4.4 KB VIDEO RAM
DMA BUS
OPIF INPUTS
START
CLK1
CLK1N/GPO[25]
CLK2/GPO[24]
FCSN[2]/VIDCTL[1]/GPO[22]
FCSN[1]/VIDCTL[0]/GPO[26]
WRPROTN
SXIN
SXOUT
TSTCLK
DEBUGN
RESETN
XIN
XOUT
PWRDWNN
BATRSTN
INTPWRDWNEN
PWR/GND
TEST
OPI[0]/GPIO[21]/SSRXD1
OPI[1]/GPIO[22]/SSSTAT1
OPI[2]/GPIO[23]/SSCLK1
OPI[3]/GPIO[24]
VIN
VREFN/CLREF
VREFP
IVREFN
IVREFP
Fig. 3
5–2
OPIF OUTPUTS
LEDCTL/GPO[16]
LCDCS/GPO[17]
OPO[0]/GPO[8]/SMPWRCTRL
OPO[1]/GPO[9]/PMPWRCTRL
OPO[2]/GPO[10]/RINGER
OPO[3]/GPO[11]
OPO[4]/GPO[12]/SSTXD1
OPO[5]/GPO[13]
OPO[6]/GPO[14]
OPO[7]/GPO[15]
THADIN
PCLK/DMAACK
PDAT
PLAT
STRB[3:0]
STRBPOL/
DMAREQ
UX-510UA
FO-1470U
SCE114 (IC9) Terminal descriptions
Pin
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Pin List
VSS
D[3]
D[2]
D[1]
D[0]
A[23]/EYEXY
A[22]/EYESYNC
A[21]/EYECLK
A[20]
A[19]
A[18]
VDD
A[17]
A[16]
A[15]
A[14]
VSS
A[13]
A[12]
A[11]
A[10]
A[9]
A[8]
A[7]
A[6]
A[5]
A[4]
VDD
A[3]
A[2]
A[1]
A[0]
GPIO[20]/ALTTONE
NC
NC
NC
NC
NC
GPIO[19]/RDY/SEROUT
GPIO[11]/BE/SERINP
VSS
PCLK/DMAACK
PDAT
PLAT
STRB[3]
STRB[2]
STRB[1]
STRB[0]
STRBPOL/DMAREQ
VDD
GPIO[17]
GPIO[16]/IRQ[8]
GPIO[15]/CS[5]n
GPIO[14]/CS[4]n
GPIO[13]/CS[3]n
GPIO[12]/CS[2]n
GPIO[4]/CPCIN
VSS
LEDCTL/GPO[16]
NC
LEDCS/GPO[17]
GPIO[7]/SSRXD2
GPIO[6]/SSTXD2
I/O
−
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
−
I/O
I/O
I/O
I/O
−
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
−
I/O
I/O
I/O
I/O
I/O
−
−
−
−
−
I/O
I/O
−
O
O
O
O
O
O
O
I
−
I/O
I/O
I/O
I/O
I/O
I/O
I/O
−
O
−
O
I/O
I/O
Input
Output
Type
Type
−
Tu
Tu
Tu
Tu
Tu
Tu
Tu
Tu
Tu
Tu
−
Tu
Tu
Tu
Tu
−
Tu
Tu
Tu
Tu
Tu
Tu
Tu
Tu
Tu
Tu
−
Tu
Tu
Tu
Tu
Hu
−
−
−
−
−
Hu
Hu
−
−
−
−
−
−
−
−
H
−
Hu
Hu
Hu
Hu
Hu
Hu
Hu
−
−
−
−
Hu
Hu
−
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
−
13Xs
13Xs
13Xs
13Xs
−
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
−
13Xs
13Xs
13Xs
13Xs
13Xs
−
−
−
−
−
13Xs
13Xs
−
3XC
2XC
3XC
1XC
1XC
1XC
1XC
−
−
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
13Xs
−
4XC
−
1XC
13Xs
13Xs
Pin Description
Digital ground.
CPU data bus.
CPU data bus.
CPU data bus.
CPU data bus.
CPU address bus.
CPU address bus.
CPU address bus.
CPU address bus.
CPU address bus.
CPU address bus.
Digital power.
CPU address bus.
CPU address bus.
CPU address bus.
CPU address bus.
Digital ground.
CPU address bus.
CPU address bus.
CPU address bus.
CPU address bus.
CPU address bus.
CPU address bus.
CPU address bus.
CPU address bus.
CPU address bus.
CPU address bus.
Digital power.
CPU address bus.
CPU address bus.
CPU address bus.
CPU address bus.
GPIO[20] or ALTTONE.
No connection.
No connection.
No connection.
No connection.
No connection.
GPIO[19], bus ready or serial port data output for autobaud detection.
GPIO[11], bus enable or serial port data input for autobaud detection.
Digital ground.
Thermal Print Head (TPH) clock or ext. DMA acknowledge.
Serial printing data (to TPH).
TPH data latch.
Strobe signal for TPH.
Strobe signal for TPH.
Strobe signal for TPH.
Strobe signal for TPH.
Sets strobe polarity active high/low or ext. DMA request.
Digital power.
GPIO[17].
GPIO[16] or ext. interrupt with priority 8.
GPIO[15] or I/O chip select 5.
GPIO[14] or I/O chip select 4.
GPIO[13] or I/O chip select 3.
GPIO[12] or I/O chip select 2.
GPIO[4] or Call Party Control input.
Digital ground.
Indicates the OPO[7:0] outputs are for LEDs or GPO[16].
No connection.
LCD Chip select or GP0[17].
GPIO[7] or SSIF2 receive data.
GPIO[6] or SSIF2 transmit data.
5–3
UX-510UA
FO-1470U
SCE114 (IC9) Terminal descriptions
Pin
No.
Pin List
I/O
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
GPIO[5]/SSCLK2
GPIO[10]/SSSTAT2
VDRAM
RASn
CAS[1]n
CAS[0]n
DWRn
VBAT
XIN
XOUT
WRPROTn
CS0n
TEST[1]
TEST[0]
BATRSTn
INTPWRDWNEn
PWRDWNn
I/O
I/O
−
O
O
O
O
−
I
O
O
O
I
I
I
I
I/O
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
NC
ADGA
VREFn/CLREF
VIN
ADGA
ADVA
ADXG
VREFp
IVREFn
IVREFp
VDD
THADI
OPO[7]/GPO[15]
OPO[6]/GPO[14]
OPO[5]/GPO[13]
OPO[4]/GPO[12]/SSTXD1
OPO[3]/GPO[11]
OPO[2]/GPO[10]/RINGER
OPO[1]/GPO[9]/PMPWRCTRL
OPO[0]/GPO[8]SMPWRCTRL
OPI[3]/GPIO[24]
OPI[2]/GPIO[23]/SSCLK1
OPI[1]/GPIO[22]/SSSTAT1
OPI[0]/GPIO[21]/SSRXD1
RESETn
VSS
GPIO[18]/IRQ[9]n
GPIO[3]/SASCLK
GPIO[2]/SASRXD
GPIO[1]/SASTXD
GPIO[9]/FRDn
GPIO[8]/FWRn
FCSn[2]/VIDCTL[1]/GPO[22]
FCSn[1]/VIDCTL[0]/GPO[23]
CLK2/GPO[24]
CLK1n/GPO[25]
CLK1
START
VDD
TONE
VSS
GPIO[25]/STROBEN
GPIO[26]/AUTOFDN
GPIO[27]/INITN
GPIO[28]/SLCTINN
GPIO[26]/ACKN
I
−
I
I
−
−
−
I
I
I
−
I
O
O
O
O
O
OZ
O
O
I/O
I/O
I/O
I/O
I/O
−
I/O
I/O
I/O
I/O
I/O
I/O
O
O
O
O
O
O
−
O
−
I/O
I/O
I/O
I/O
O
Input
Type
Output
Type
Hu
Hu
−
−
−
−
−
−
Osc1
−
−
−
Hd
Hd
H
H
H
13Xs
13Xs
−
13Xs
13Xs
13Xs
13Xs
−
−
Osc1
1XC
13Xs
−
−
−
−
13Xs
Analog
−
VADG
−
VR−
VA
−
VADG
−
VADV
−
VXG
−
VR
−
VR−
VR+
−
−
−
Analog
−
−
13Xs
−
13Xs
−
13Xs
−
13Xs
−
13Xs
−
13Xs
−
13Xs
−
13Xs
Hu
13Xs
Hu
13Xs
Hu
13Xs
Hu
13Xs
Hu
2XC
−
−
Hu
13Xs
Hu
13Xs
Hu
13Xs
Hu
13Xs
Hu
13Xs
Hu
13Xs
−
13Xs
−
13Xs
−
13Xs
−
13Xs
−
2XC
−
2XC
−
−
−
Analog
−
−
Hu
13Xs
Hu
13Xs
Hu
13Xs
Hu
13Xs
−
13Xs
Pin Description
GPIO[5] or SSIF2 clock.
GPIO[10] or SSIF2 status.
DRAM battery power.
(Batt. Pwr.) DRAM row address select.
(Batt. Pwr.) DRAM column address select.
(Batt. Pwr.) DRAM column address select.
(Batt. Pwr.) DRAM write.
Battery power.
(Batt. Pwr.) 32.768kHz Crystal Oscillator input.
(Batt. Pwr.) 32.768kHz Crystal Oscillator output.
(Batt. Pwr.) Write protect during loss of VDD power.
(Battery Powered) SRAM Chip select.
(Batt. Pwr.) Test mode.
(Batt. Pwr.) Test mode.
(Batt. Pwr.) Battery power reset input.
(Batt. Pwr.) Internal power down select signal.
(Batt. Pwr.) Indicates a prime power loss from ext./internal source
(mode dependent).
No Connection.
A/D analog ground.
Negative reference voltage for Video A/D.
Analog Video A/D input.
A/D analog ground.
A/D analog power.
A/D internal ground.
Positive reference voltage for Video A/D.
Internal negative reference voltage for A/D.
Internal positive reference voltage for A/D.
Digital power.
Analog Thermal A/D input.
Keyboard LED strobe 7 or GPO[15].
Keyboard LED strobe 6 or GPO[14].
Keyboard LED strobe 5 or GPO[13].
Keyboard LED strobe 4 or GPO[12] or transmit data for SSIF1.
Keyboard LED strobe 3 or GPO[11].
Keyboard LED strobe 2 or GPO[10] or ringer.
Keyboard LED strobe 1 or GPO[9] or Printer motor power control.
Keyboard LED strobe 0 or GPO[8] or Stepper motor power control.
Keyboard return 3 or GPIO[24].
Keyboard return 2 or GPIO[23] or SSIF1 clock.
Keyboard return 1 or GPIO[22] or SSIF1 status.
Keyboard return 0 or GPIO[21] or SSIF1 receive data.
Chip reset.
Digital ground.
GPIO[18] or ext. interrupt priority 9.
GPIO[3] or SASIF clock.
GPIO[2] or SASIF receive data.
GPIO[1] or SASIF transmit data.
GPIO[9] or flash read enable signal for NAND-type flash memory.
GPIO[8] or flash write enable signal for NAND-type flash memory.
Flash memory chip select 2 or video control signal 1 or GPO[22].
Flash memory chip select 1 or video control signal 1 or GPO[23].
Scanner reset gate control (or clock for CIS scanner) or GPO[24].
Scanner clock-inverted or GPO[25].
Scanner clock.
Scanner shift gate control.
Digital power.
Analog tone output.
Digitai ground.
GPIO[25] or P1284 input from host.
GPIO[26] or P1284 input from host.
GPIO[27] or P1284 input from host.
GPIO[28] or P1284 input from host.
GPIO[26] or P1284 returned status to host.
5–4
UX-510UA
FO-1470U
SCE114 (IC9) Terminal descriptions
Pin
Pin List
No.
I/O
Input
Output
Type
Type
127
128
129
130
131
GPO[27]/BUSY
GPO[28]/PERROR
GPO[29]/SLCTOUT
GPO[30]/FAULTN
GPIO[29]/PIOD[0]
O
O
O
O
I/O
−
−
−
−
Hu
13Xs
13Xs
13Xs
13Xs
13Xs
132
GPIO[30]/PIOD[1]
I/O
Hu
13Xs
133
GPIO[31]/PIOD[2]
I/O
Hu
13Xs
134
GPIO[32]/PIOD[3]
I/O
Hu
13Xs
135
GPIO[33]/PIOD[4]
I/O
Hu
13Xs
136
GPIO[34]/PIOD[5]
I/O
Hu
13Xs
137
GPIO[35]/PIOD[6]
I/O
Hu
13Xs
138
GPIO[36]/PIOD[7]
I/O
Hu
13Xs
139
140
141
142
143
144
VDD
GPIO[0]/SR4IN
GPO[31]/SR3OUT
GPIO[37]/IRQ15n
IARESET
IACLK/DSPCSn
−
I/O
O
I/O
O
O
−
Hu
−
Hu
−
−
−
13Xs
13Xs
13Xs
13Xs
13Xs
145
146
IA1CLK
SR3IN/DSPIRGn
I/O
I
H
H
13Xs
13Xs
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
SR4OUT
SR1IO
SA1CLK
VSSPLL
TSTCLK
DEBUGn
RDn
WRn
SYNC/GPO[20]
ROMCSn
CS1n/GPO[21]
VSS
SXIN
SXOUT
VDD
PM[3]/GPO[3]
PM[2]/GPO[2]
PM[1]/GPO[1]
PM[0]/GPO[0]
SM[3]/GPO[7]
SM[2]/GPO[6]
SM[1]/GPO[5]
SM[0]/GPO[4]
REGDMA/GPO[18]/CLKConfig[0]
O
I/O
I/O
−
O
I
O
O
I/O
O
O
−
I
O
−
O
O
O
O
O
O
O
O
O
171
WAITn/GPO[19]/CLKConfig[1]
I/O
Hu
13Xs
172
173
174
175
176
VDDPLL
D[7]
D[6]
D[5]
D[4]
−
I/O
I/O
I/O
I/O
−
Tu
Tu
Tu
Tu
−
13Xs
13Xs
13Xs
13Xs
−
13Xs
H
13Xs
H
13Xs
−
−
−
13Xs
Hu
−
−
13Xs
−
13Xs
Hu
13Xs
−
13Xs
−
13Xs
−
−
OSC0
−
−
OSC0
−
−
−
13Xs
−
13Xs
−
13Xs
−
13Xs
−
13Xs
−
13Xs
−
13Xs
−
13Xs
−
13Xs
Pin Description
GPO[27] or P1284 returned status to host.
GPO[28] or P1284 returned status to host.
GPO[29] or P1284 returned status to host.
GPO[30] or P1284 returned status to host.
GPO[29] or P1284 data or address driven by asic or host
(mode dependent).
GPO[30] or P1284 data or address driven by asic or host
(mode dependent).
GPO[31] or P1284 data or address driven by asic or host
(mode dependent).
GPO[32] or P1284 data or address driven by asic or host
(mode dependent).
GPO[33] or P1284 data or address driven by asic or host
(mode dependent).
GPO[34] or P1284 data or address driven by asic or host
(mode dependent).
GPO[35] or P1284 data or address driven by asic or host
(mode dependent).
GPO[36] or P1284 data or address driven by asic or host
(mode dependent).
Digitai power.
GPIO[0] or from secondary EXTIA SOUT to DSP.
GPO[31] or a signal to the secondary ext. IA (SIN pin) from the DSP.
GPIO[37] or a signal from the ext. IA to a DSP status register.
A reset from the DSP to the ext. IA (POR pin).
A signal from the DSP to the ext. IA (MCLK pin) or ext. modem chip
select.
A signal from the ext. IA (ICLK pin) to the DSP.
A signal from the primary ext. IA (SOUT pin) to the DSP or ext.
modem interrupt input.
A signal to the primary ext. IA (SIN pin) from the DSP.
A signal to the ext. IA (CTRL1 pin) from the DSP.
A signal from the ext. IA (FSYNC pin) to the DSP.
Ground for PLL.
Test clock, used to synchronize ext. logic.
External non-maskable input (NMI).
Read strobe.
Write strobe.
Indicates a CPU op code fetch cycle or GPO[20].
ROM chip select.
I/O chip select or GPO[21].
Digital ground.
32.256MHz crystal oscillator input.
32.256MHz crystal oscillator output.
Digital power.
Programmable print motor control pin or GPO[3].
Programmable print motor control pin or GPO[2].
Programmable print motor control pin or GPO[1].
Programmable print motor control pin or GPO[0].
Programmable scan motor control pin or GPO[7].
Programmable scan motor control pin or GPO[6].
Programmable scan motor control pin or GPO[5].
Programmable scan motor control pin or GPO[4].
Register select cycle/dma cycle or GPO[18] and sxin clock divider
config. during reset.
Wait state/halt state indication or GPO[19] and sxin lock divider config.
during reset.
Power for PLL.
CPU data bus.
CPU data bus.
CPU data bus.
CPU data bus.
5–5
UX-510UA
FO-1470U
(2) Panel control block
The following controls are performed by the SCE114.
•
Operation panel key scanning
•
Operation panel LCD display
(3) Mechanism/recording control block
•
Recording control block diagram (1)
OPERATOR
PANEL,
KEYPAD,
LEDS & LCD
PRINTER DATA
CONTROI &
SENSORS
OPO[7:0]*
OPI[3:0]*
LEDCTL*
LCDCS*
STRB[3:0]
STRBPOL
THADI
PDAT
PCLK
PLAT
SASCLK*
SASTXD*
SASRXD*
LINE
INTERFACE
IA
RIN
TXOUT
SCE114
1-CHIP
FAX ENGINE
SECONDARY
IA
SPEAKER
MICROPHONE
CIRCUIT
MIC
SYNC/ASYNC
SERIAL PORT
SASIF
GPIO
RXIN
TXOUT
SPKR
GENERAL
PURPOSE I/O
SSCLK[2:1]*
SSTXD[2:1]*
SSRXD[2:1]*
SSSTAT[2:1]*
TELEPHONE
LINE
TXA
SERIAL SYNC
PORTS
(2)
(SSIF)
SYSCLK
CRYSTAL
ANALOG
SWITCH
SPKRH
SPKRL
RIN
SR4IN*
SR3OUT*
A[23:0]
D[7:0]
RDN
WRN
ROMCSN
EXTERNAL BUS
SCANNER
VIDEO
PREPROCESSING
VIDCTL[1:0]
VIN
VREFP
VREFN
IVREFP
IVREFN
SXIN
SXOUT
RXA
SCANNER
CONTROLS &
SENSORS
SM[3:0]*
START
CLK2
CLK1
CLK1N
RTC
CRYSTAL
SR3IN
SR4OUT
IA1CLK
SA1CLK
IACLK
SR1IO
IARESET
PM[3:0]*
PRINTER &
SCANNER
MOTOR DRIVERS
TEST[1:0]
BATRSTN
RESETN
TONE
ALTTONE
TSTCLK
REGDMA
WAITN
SYNC
PWRDWNN
INTPWRDWNEN
XIN
XOUT
CAS[0,1]N, RASN, DWRN
CS[5:0]N*
CS3N,
CS4N**
WRPROTN
FRDN*
FRWN*
FCLE*
FCSN[2:0]
DEBUGN
VDD
VDRAM
VBAT
VSS
ADVA
ADGA
D7[7:0]
DRAM
(OPTION)
FLASH MEMORY
NOTES: * ALTERNATIVE GPO, GPI OR GPIO LINES
**FOR SAMSUNG NAND-TYPE FLASH
SPEAKERPHONE ONLY
VOICE OR SPEAKERPHONE
Fig. 4
5–6
UX-510UA
FO-1470U
(4) Modem (SCE114/20415) block
FEATURES
INTRODUCTION
•
The CONEXANT SCE114 modem is a synchronous 14400 bits per second (bps) half-duplex modem with error detection and DTMF reception.
It has low power consumption and requires +5V and +3.3V DC power
supply.
The modem can operate over the public switched telephone network
(PSTN) through line terminations provided by a data access arrangement (DAA).
The SCE114 is designed for use in Group 3 facsimile machines.
The modem satisfies the requirements specified in ITU-T recommendations V.17, V.29, V.27 ter, V.21 Channel 2 and T.4, and meets the binary
signaling requirements of T.30.
The modem can operate at 14400, 12000, 9600, 7200, 4800, 2400, or
300 bps, and also includes the V.27 ter short training sequence option.
The modem can also perform HDLC framing according to T.30 at 9600,
7200, 4800, 2400, or 300 bps.
The modem features a programmable DTMF receiver and three programmable tone detectors which operate concurrently with the V.21
channel 2 receiver.
The voice mode allows the host computer to efficiently transmit and
receive audio signals and messages.
•
Group 3 facsimile transmission/reception
-
ITU-T V.17, V.33, V.29, V.27 ter, T.30, V.21 Channel 2, T.4
-
ITU-T V.17 and V.27 ter short train
-
HDLC framing at all speeds
-
Receive dynamic range: 0 dBm to -43 dBm
-
Automatic adaptive equalization
-
Fixed and programmable digital compromise equalization
-
DTMF detect and tone detect
-
ITU-T V.21 Channel 2 FSK 7E Flag Detect
-
Ring detector
-
Programmable transmits level
-
Programmable single/dual tone transmission
V.23 and Type I Caller ID
-
Full-duplex modes:
TX = 75 bps. RX = 1200 bps
TX = 1200 bps. RX = 75 bps
-
Half-duplex mode:
TX = RX = 1200 bps
DSP
SA1CLK
FSYNC
IA1CLK
ICLK
IACLK
MCLK
IA
MODE 0
SR1IO
CTRLSIN
MODE1
SR4OUT
SIN
SR3IN
SOUT
GPO0
POR
SCE114
TYPICAL EXTERNAL HYBRID
TYPICAL MICROPHONE
CIRCUIT
TYPICAL SPEAKER CIRCUIT
LINEIN
LINEO
Connections for MODE 0
and MODE 1 pins are
shown for a Line IA.
Fig. 5
5–7
Programmable parallel data mode
-
5, 6, 7 or 8 data bits
-
1 or 2 Stop bits
-
Mark, Space, Even, or Odd Parity
-
Break function
-
Transmitter squelch
-
Compromise equalizer
Programmable interface memory interrupt
•
DTE interface: two alternate ports
•
•
•
SPKRO+
SPKRO–
Serial and parallel data modes
-
•
•
GND
MICIN+
MICIN–
-
Eight General Purpose Input (GPI) and eight General Purpose Output (GPO) pins for host assignment
-
Selectable microprocessor bus (6500 or 8085)
-
ITU-T V.24 (EIA/TIA-232-E compatible) interface
TTL and CMOS compatible
3.3V/5V operation
Power consumption
-
Operating Mode: 200 mW (Basic), 275 mW (-V option). 300 mW
(-VS option)
-
Sleep Mode: 1 ma (Basic. -V option and -VS option)
UX-510UA
FO-1470U
[3] Circuit description of TEL/LIU PWB
(1) TEL/LIU block operational description
INTEGRATED ANALOG
20415
1) Block diagram
TEL/LIU PWB
SP OUT
ENABLE
CONTROL PWB
TXOUT
RTLOOP
SPKRP-P
L1
C
CML
M
(0:1)
(1:0)
(0:0)
(1:1)
MIC ENABLE
SIN
DAC
SP
DRIVER
L2
DAC GAIN
0,6dB
B
CI
RXIN
MIC
GAIN
MICP
MIC IN
LPF
MIC
1 ENABLE
0
0,20,25,30dB
ADC
SOUT
LINE IN
TELIN
LINEIN
LINE IN
LPF
1 ENABLE
0
ADC GAIN
0,–4dB
HANDSET
RX
TELMUTE
TX
RCV VOL
DTMFMUTE
LINE
DRIVER
TELOUT
LNINSEL
(0:0)
(1:1)
(1:0)
LINEOUT
LINEOUT
ENABLE
MUTE,0,
–6,–12dB
SPEAKER
IACR1
IACR2
BIT7
DAC
GAIN
TXRX
LOOP
BIT6
BIT5
MIC GAIN
BIT4
L/O E
BIT3
SPKR E
LINEOUT
ATTENUATION
IACR3
BIT2
BIT1
ADC
L/I E
GAIN
RXTXLOOP
BZOUT
CML
SPMUTE
BIT0
MIC E
MICBIAS
SEL
LINE SEL
HS
CI
SPMUTE
DTMFMUTE
FAX
ENGINE
SCE114
CSWI
PESNS
FRSNS
ORGSNS
PSNS
RCVOL
LEDON
VTHON
RHS
DRSNS
TXMUTE
TELMUTE
IA-RESET
Fig. 6
2) Circuit description
3) Block description
The TEL/LIU PWB is composed of the following 7 blocks.
1. Speech circuit section
1. Speech circuit section
•
2. Dial transmission section
3. Speaker amplifier section
The receiver volume is an electronic volume type, this model is
switched in 3 steps.
2. Dial transmission section
4. Ringer circuit section
•
D.P. transmission: The CML relay is turned on and off for control in
the DP calling system. (Refer to the attached sheet.)
•
DTM transmission: It is formed in the modem, and is output.
5. Externally connected TEL OFF HOOK detection circuit
6. CI detection circuit
7. Signal/DTMF transmission level & receiving level
3. Speaker amplifier section
•
Ringer volume
•
Speaker volume :It is controlled by the attenuator value of the
LINE DRIVER in the modem.
:It is controlled by the combination of the
attenuator value of the LINE DRIVER in the
modem and the ringer sending level sent from
the modem.
4. Ringer circuit section
•
5–8
The ringer sound is formed in the tone of modem when CI signal is
detected. The amplifier circuit drives the speaker of the main body.
UX-510UA
FO-1470U
5. Externally connected TEL OFF HOOK detection circuit section
•
4) Signal selection
The following signals are used to control the transmission line of TEL/
FAX signal. For details, refer to the signal selector matrix table.
The circuit current detection is turned on together with OFF HOOK
of main body or OFF HOOK of externally connected TEL. ON of
CML OFF (HS=L) is judged as OFF HOOK of externally connected
TEL.
[Control signals from output port]
Signal Name
6. CI detection circuit
•
CI is detected by the photo coupler which is integrated in series in
the primary side TEL circuit well proven in the existing unit.
SP MUTE
7. Signal/DTMF transmission level & receiving level
•
Signal transmission level setting: ATT -10 dB Circuit output: -12 dBm.
•
DTMF transmission level setting: HF -3.5 dBm
Thus, set the level.
Description
Line connecting relay and DP generating relay
(The circuit is located H: Line make
in the TEL/LIU PWB.) L: Line break
CML
(The circuit is located
in the TEL/LIU PWB.)
LF -5.0 dBm
TEL MUTE
Speaker tone mute control signal
H: Muting (Power down mode)
L: Muting cancel (Normal operation)
Handset reception mute control signal
H: Muting
L: Muting cancel
Handset receiver volume control signal
RCVOL
DTMFMUTE
(The circuit is located
in the control PWB.)
Volume
RCVOL
DTMFMUTE
High Middle
L
L
H
L
Low DTMF sending
L
H
L
H
Note: The DTMF sending listed above is DTMF signal
sending in the handset OFF-HOOK mode.
LINEOUT A
VOLUME SETTING
Receiver volume setting
Low
High
Middle
Fixed
DTMF Transmission
volume setting (Receiver)
Key buzzer volume setting Fixed
Speaker volume setting
Low
Middle
High
Ringer volume setting
Low
Middle
High
DTMF speaker volume
Low
setting
Middle
High
5–9
RCVOL DTME
(HIGH) (LOW)
MUTE
0
0
1
0
1
1
0
1
1
0
1
1
0
1
0
1
1
0
1
1
0
1
1
0
0
1
UX-510UA
FO-1470U
[Signals for status recognition according to input signals]
No.
Signal Name (CNLIUA)
No.
Signal Name (CNLIUA)
1
PE1
8
TXOUT
H:The handset is in the on-hook state.
2
TEL OUT
9
RXIN
L: The handset is in the off-hook state.
3
TEL IN
10
RHS
Incoming call (CI) detection signal
H: Door open.
4
5
TEL MUTE
11
DOOR SW
CI
12
+5V
L: Door close.
6
7
HS
CML
13
DG
+24V
Signal Name
RHS
CI
DRSNS
Function
14
[Other signals]
Signal Name
TEL IN
Function
Receiving signal from line or modem
TEL OUT
Transfer signal to line
SPOUT
Speaker output signal
Transmission (DTMF) analog signal output
TXOUT
from modem
Reception (DTMF, others) analog signal input
RXIN
into modem
(Example: TEL speaking)
INTEGRATED ANALOG
20415
TEL/LIU PWB
SP OUT
ENABLE
CONTROL PWB
TXOUT
RTLOOP
SPKRP-P
L1
C
CML
M
(0:1)
(1:0)
(0:0)
(1:1)
MIC ENABLE
DAC
SP
DRIVER
L2
SIN
DAC GAIN
0,6dB
B
CI
RXIN
MIC
GAIN
MICP
MIC IN
LPF
MIC
1 ENABLE
0
0,20,25,30dB
ADC
TELIN
LINEIN
LINE IN
LPF
LINE IN
1 ENABLE
0
ADC GAIN
0,–4dB
HANDSET
RX
TELMUTE
TX
RCV VOL
DTMFMUTE
LINE
DRIVER
TELOUT
LINEOUT
ENABLE
LNINSEL
(0:0)
(1:1)
(1:0)
LINEOUT
MUTE,0,
–6,–12dB
SPEAKER
IACR1
IACR2
IACR3
BIT7
DAC
GAIN
TXRX
LOOP
BIT6
BIT5
MIC GAIN
BIT4
BIT3
BIT2
BIT1
BIT0
L/O E SPKR E ADC
L/I E
MIC E
GAIN
LINEOUT
RXTXLOOP MICBIAS
ATTENUATION
SEL
LINE SEL
BZOUT
CML
SPMUTE
SPMUTE
HS
CI
TEL SPEAKING:
FAX SENDING/RECEIVING:
DTMFMUTE
RCVOL
VTHON
FAX
ENGINE
SCE114
CSWI
PESNS
FRSNS
ORGSNS
PSNS
LEDON
RHS
DRSNS
TXMUTE
TELMUTE
IA-RESET
Fig. 7
5 – 10
SOUT
UX-510UA
FO-1470U
[4] Circuit description of power supply PWB
1. Block diagram
2.5A/125V
Noise
Filter
Circuit
AC IN
Rectifying
Smoothing
Circuit
Switching
Circuit
(RCC system)
Regulator
Circuit
+5V
+24V
FUSE
4A/72V
Control
Circuit
Photo Coupler
Fig. 8
2-1. Noise filter circuit
2-4. Control circuit
The input noise filter section is composed of L1 and C1, C15, which
reduces normal mode noise from the AC line and common mode noise
to the AC line.
This circuit controls output voltage of +24V by adjusting ON period of
Q1, looking at signal from photo coupler PC1.
2-2. Rectifying/smoothing circuit
The over current protection is performed by bringing Q1 to OFF state
through detection of voltage of T1 subwiding.
In this operation IC1 takes charge of important part.
The AC input voltage is rectified by diode stack DS1 and smoothed by
capacitor C2 to supply DC voltage to the switching circuit section.
The over voltage protection is performed by operating the over current
protection circuit through detection of zener diode ZD4 and short-circuiting
of load.
2-3. Switching circuit
This circuit includes MOS FET Q1 and the gate drive circuit, and components around Q1.
2-5. +5V circuit
DC voltage supplied by rectifying the output of transformer T1 with diode
D8 is stabilized by 3-terminal regulator IC1.
In this circuit, the DC voltage supplied from the rectifying/smoothing
section is converted into high frequency pulses by ON/OFF repetition of
Q1.
[5] Circuit description of CCD PWB
The CCD board picks up optical information from the document, converts it into an electrical (analog) signal and transfers it to the control
board.
(2) Description of blocks
1. CCD
The TCD1208AP is a highly sensitive charged coupled image sensor
that consists of 2160 picture elements.
(1) Block diagram
Receiving four drive signal (øT, ø2, ø1, øR) from the control board, the
transferred photoelectric analog signal OS is impedance converted, and
the signal VO, is supplied to the control board.
ΦT
Φ1
2. Waveforms
Φ2
1. ø1, ø2 (=ø1) signals within the control board.
ΦR
Approx. 5V
øT
CCD
TCD1208AP
0V
+5V
Approx. 5V
ø1 (=ø2)
0V
GND
VO
OUTPUT CIRCUIT
(emitter follower)
2. OS ø
OS
1.74µ SEC
Approx. 5V
Fig. 9
øR
0V
Approx. 100mV
OS
Fig. 10
5 – 11
6–1
CNPN-4
CNPN-3
A
KEN1A
KEN2A
KEN3A
R189
R198
0
0
DG
B
2Y1
2Y2
2Y3
2Y4
1 1OE
19 2OE
9
7
5
3
1Y1
1Y2
1Y3
1Y4
11
13
15
17
2
4
6
8
GND 10
VCC 20
2A1
2A2
2A3
2A4
1A1
1A2
1A3
1A4
IC2 HCT244
C
R130
270
1
4
10
13
12
9
5
2
1OE
2OE
3OE
4OE
1A4
1A3
1A2
1A1
GND
VCC
1Y4
1Y3
1Y2
1Y1
7
14
11
8
6
3
IC3 LV125A
DG
VIDCNT1
(3-1A)
RA 5 470
4
3
2
1
+5V
DG
DG
C128
1
5
6
7
8
49
R125
10K
RA 6
470
D
+3.3V
DG
C127
1
R128
270
DG
E
2.2
C159
N.M.
RA 11
1K
DG
DG
DGA
F
+3.3V
DGA
C160
SCE114(1/2)
IC9
DGA
TONE 120
CNPN-2
R188
0
18
16
14
12
STRB3
STRB2
STRB1
STRB0
PCLK
PDAT
PLAT
45
46
47
48
42
43
44
C158
DGA
C141
DGA
C134
DGA
DGA
DG
C146
DG
C137
1
G
G
DG
C115
18P
X1
10M
R113
DGA
+3.3V
88
83
84
92
CNPN-1
KEN4A
DG
N.M.
R165
0
START
118
91 VDD
VIDCNT1-A
(5-4B)
E
R117
0
DGA
CLK2
115
STRBPOL
CLK1N/GPO25
116
DGA
C142
1
VDRAM 66
CNPN-10
CNPN-15
SEN0
SEN1
SEN2
SEN3
R116
C177
C179
C178
C144
C152
C163
C164
0
1000P X 7
CLK1
117
+3.3V
DGA
C140
1
F
XIN 72
1
2
CNPN-14
CNPN-13
CNPN-12
270
R133
DGA
C174
15P
R170
220
160 SXOUT
159 SXIN
C139
1
87 ADXG
DG
270
100P X7
270
R136
4
3
2
1
4
3
2
1
R134
5
6
7
8
RA1
470
RA14
470
X2
1M
R171
76 TEST1
77 TEST0
C118
1
82,85 ADGA
SEN4
LATCH
DATA
PCLK
STRB1
STRB2
STRB3
STRB4
CLK1
CLK1
CLK2
START
5
6
7
8
C175
15P
32.256MHz
DGA
+3.3V
89 IVREFN
CNPN-11
CNTH-13
CNTH-15
CNTH-14
CNTH-3
CNTH-4
CNTH-11
CNTH-12
(5-3A)
(5-2A)
(5-2A)
(5-2A)
DG
DGA
86 ADVA
3
4
5
6
+3.3V
90 IVREFP
L107
+ C6
220/6.3
119 VDD
104
103
102
101
59
61
100
99
98
97
96
95
94
93
0
C114
2.2
E
139 VDD
OPI0
OPI1
OPI2
OPI3
LEDCTL
LCDCS
OPO0
OPO1
OPO2
OPO3
OPO4
OPO5
OPO6
OPO7
4
3
2
1
+3.3V
50 VDD
5
6
7
8
[1] Control PWB circuit Main control block
D
12 VDD
C120
C145
C124
C123
C122
C121
28 VDD
4
3
2
1
2.2
C161
C
161 VDD
169
168
167
166
5
6
7
8
DGA
C148
<L>
<M>
B
172 VDDPLL
SM0
SM1
SM2
SM3
TPB
TPA
TPB
TPA
C131
C133
C132
C112
C113
C109
C110
C157
2.2
1 VSS
1000P
1000P
1000P
1000P
2.2
150 VSS
C135
2.2
121 VSS
(6-3I) BZOUT1
158 VSS
0.1
2.2
ALTTONE/GPIO20 33
C151
C150
C149
C143
C116
33P
DG
+3.3V
H
DG
<J>
<H>
<I>
155
170
171
67
69
68
70
74
SYNC
REGDMA/CLKCONFIG0
WAIT/CLKCONFIG1
RAS
CAS0
CAS1
DWR
WRPROT
C130
1
DG
270
<G> 270
270
153
154
156
157
75
RD
WR
ROMCS
CS1
CS0
H
C117 1
DG
4
3
2
1
5
6
7
8
29
30
31
32
A3
A2
A1
A0
C136
1
4
3
2
1
5
6
7
8
24
25
26
27
A7
A6
A5
A4
R129
220K
4
3
2
1
5
6
7
8
20
21
22
23
A11
A10
A9
A8
D[7:0]
A3
A2
A1
A0
A7
A6
A5
A4
A11
A10
A9
A8
A15
A14
A13
A12
A18
A17
A16
R124
0
DGA
DG
I
<BATRST>
R123
R127
R140
0
0
RA 2
270
RA 3
270
RA 4
270
RA 8
270
4
5
6
DWR
(2-4G)
1
2
RAS (2-4G) 3
CAS0 (2-4G)
CE1 (2-4D)
RD (2-3G)
WR (2-4D,1E)
ROMCS (2-4A)
A[18:0]
(2-6A)
1/6
RA 7
270
I
(2-5A)
R143
R141
R142
10K
4
3
2
1
5
6
7
8
15
16
18
19
A15
A14
A13
A12
<A>
<B>
<C>
<D>
<E>
<F>
4
3
2
1
6
7
8
9
10
11
13
14
A23
A22
A21
A20
A19
A18
A17
A16
RA 9
270
5
6
7
8
BATREST 78
(5-5F)
(5-5F)
(5-4F)
(5-4F)
XOUT 73
C173
C172
C156
C155
2.2
106 VSS
(6-3I) BZOUT2
C147
58 VSS
+VREF
-VREF/CLREF
VIN
THADI
C138
2.2
41 VSS
1
1000P
INTPWRDOWNE 79
(6-3F) THADI
(6-3F)
VIN
2.2
17 VSS
32.768kHz
<K>
R131
152 DEBUGN
PWRDWN 80
PWRDWN
151 TETCLK
VBAT 71
VBAT
RESET0 (4-1B)
105 RESET
10K
D4
D5
D6
D7
N.M.
176
175
174
173
D0
D1
D2
D3
R114
5
4
3
2
(4-2D)
D7
D6
D5
D4
RA 10 270
1
2
3
4
8
7
6
5
D3
D2
D1
D0
1
2
3
4
8
7
6
5
A
UX-510UA
FO-1470U
CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS LAYOUT
6–2
D[7:0]
A[18:0]
B
27L020
OE 24
GND 16
C
DG
C100
0.1
+3.3V
D0
D1
D2
D3
D4
D5
D6
D7
(1-4D) CE2
(1-3I) WR
(1-3I) CE1
D
R115
22K
VBT
N.M.
R118
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
E
R119
0
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
11
12
13
15
16
17
18
19
VSS 14
VCC 28
IO1
IO2
IO3
IO4
IO5
IO6
IO7
IO8
W24258
22 CS2/OE
27 WE
20 CS1
10
9
8
7
6
5
4
3
25
24
21
23
2
26
1
F
C129
0.1
DG
VBT
D0
D1
D2
D3
D4
D5
D6
D7
(1-3I) DWR
(1-3I) CAS0
(1-3I) RAS
+3.3V
G
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
10K
10K
10K
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
IC 5
H
2
3
4
5
24
25
26
27
GND 28
GND 15
NC 21
VCC 1
VCC 14
DQ0
DQ1
DQ2
DQ3
DQ4
DQ5
DQ6
DQ7
MSM51V4800E
22 OE
7 WE
23 CAS
8 RAS
6 NC
10
11
12
13
16
17
18
19
20
9
H
DG
C126
0.1
I
I
+3.3V
D0
D1
D2
D3
D4
D5
D6
D7
2/6
4
5
6
1
22 CE
13
14
15
17
18
19
20
21
VCC 32
VPP 1
D0
D1
D2
D3
D4
D5
D6
D7
G
1
A
R105 N.M.
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
IC 8
F
2
R104
10K
12
11
10
9
8
7
6
5
27
26
23
25
4
28
29
3
2
30
31
E
2
+3.3V
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
IC 4
D
R221
3
(1-3I) RD
(1-3I) ROMCS
(1-6I)
(1-5I)
C
R220
3
4
5
6
Memory block
B
R222
A
UX-510UA
FO-1470U
6–3
1
2
3
4
5
(6-2F) VOL-A
(6-2F) VOL-B
(6-2F) VOL-C
(5-3E) VTHON
(1-2A) VIDCNT1
CNLIUB-1
CNLIUB-3
(5-4F) LEDON
(6-2E) CML
CNLIUA-7
CNLIUA-4
(5-1A) PNLON
(4-5D) RBNSNS
CNPW-7
(4-3D) FRSNS
(4-3D) ORGSNS
CSWI
DRSNS
(4-6D)
(4-5D)
CNLIUB-4
CNLIUB-2
CNLIUB-5
(6-1E,5E) RCVOL
(5-6A) GCONT
SPMUTE
(6-4F)
CNLIUA-10
(4-4D) PINSNS
CNLIUA-1
CNLIUA-6
CNLIUA-5
A
C208
N.M.
R149
DG
C199
B
R132 0
162
163
164
165
GPO3
GPO2
GPO1
GPO0
C
114 GPO23/FCS/VIDCOTL0
113 GPO22/VIDCNT1
126 GPO26
127 GPO27
R150
DPON
N.M.
GPIO1
GPIO0
GPO31
GPO30
129 GPO29
110
140
141
130
109 GPIO2
108 GPIO3
128 GPO28
N.M.
N.M.
C
GPIO9/FRD
GPIO8/FWR
GPIO7
GPIO6
GPIO5
GPIO19
GPIO18
GPIO17
GPIO16
GPIO15
GPIO14
GPIO13
GPIO12
GPIO11
GPIO10
57 GPIO4
111
112
62
63
64
39
107
51
52
53
54
55
56
40
65
122 GPIO25
123 GPIO26
R145
DG
R146 470
R137 0
R172 270
N.M.
124 GPIO27
125 GPIO28
131 GPIO29
132 GPIO30
133 GPIO31
134 GPIO32
135 GPIO33
136 GPIO34
137 GPIO35
R144 1K
DG
C201
C205
R135 270
R138
DG
3
2
1
4
3
2
1
142 GPIO37
138 GPIO36
RLYCONT
CML
TELMUTE
DG
C103
R147
PSAVE
270
RA 13
RA 12
270
C217
6
7
8
5
6
7
8
R148
C215
DG
ERLY
N.M.
C212
C203
DPMUTE
DG
TXMUTE
RCVOL
GCONT
SPMUTE
RHS
PIN
PE1
HS
CI
SIGMUTE
DTMFMUTE
C200
(6-4D) SIGMUTE
(6-1E) DTMFMUTE
C167
6
C204
Modem block
B
IC 9
SCE114(2/2)
D
D
149
145
144
148
147
146
NC
NC
NC
NC
NC
NC
NC
34
35
36
37
38
60
81
IARESET 143
SA1CLK
IA1CLK
IACLK
SR1IO
SR4OUT
SR3IN
E
E
R213
0
DG
C222
R203 270
R204 270
R101 270
DG
R202
0
N.M.
F
F
FSYNC
ICLK
MCLK
CTRLSIN
SIN
SOUT
25
27
28
29
30
32
NC
NC
NC
NC
NC
NC
2 RESERVED
3 RESERVED
22 RESERVED
24 MODE0
23 MODE1
7 POR
6
26
31
1
5
4
IC 13
20415
MICIN- 11
MICIN+ 10
AGND 14
VREF 13
AVSS 8
AVSS 16
AVDD 15
DVSS 20
DVDD 21
G
C220
0.1
MAG
C14 MAG
10/50
C12
10/50
SIGTX
SIGRX
DG
(6-2E)
3/6
I
(6-4F)
(6-5E)
(6-4D)
SPOUT
1K
+
I
+5.0V
LINEO 17
R200
2.2K
H
C198 0.1
C15
10/50
R201
+
C197
0.1
+3.3V
TELOUTI
C221
0.1
DG
C176
0.1
H
LINEIN 9
SPKRO- 19
SPKRO+ 18
MICBAIS 12
G
+
A
1
2
3
4
5
6
UX-510UA
FO-1470U
6–4
A
CNPN-8
C108
+3.3V
1K (1W)
R1
DG
DG
2
1
2
1
DG
B
N.M.
R206
270
N.M.
R173
270
N.M.
N.M.
DGA
270
R108
XC61AN
OUT 1
IC 100
R120
51K
C106
C119
270
R109
SG206S
PI 1(P-IN)
SG206S
PI 2 (INK)
C202
R122
3 VCC
DG
<DRSNS>
DG
C181
2
RESETO
ORGSNS
FRSNS
<+24V>
DOOR SW
CSW
GND
1
2
3
CNPN-9
+24V
CNLIUA-11
CNCSW-1
4
3
4
3
B
DG
DG
R121
DG
DG
DG
C
DG
Q 103
R112
E
C
C105
100P
C107
100P
<PINSNS>
<RBNSNS>
<DRSNS>
C180
100P
N.M.
ORGSNSi
FRSNSi
PINSNS
CE2 (2-4D)
D
PWRDWNI (1-1H)
(3-3A)
(3-3A)
(3-5A)
RBNSNS (3-2A)
DRSNS (4-3A)
CSWi (3-4A)
D
E
CNPW-4
CNPW-3
CNPW-2
CNPW-1
CNPW-8
CNPW-6
CNPW-5
E
MG
MG
+24V
+24V
DG
DG
+5V
R103
DG
+
4
C
F
CR2032
BAT1
F
C102
1
N.M.
MG
R100
R215
+5V
5.6K
R107
C104
0.1
FG
R216
G
D 101
1SS355
DG
+24V
DG
2
G
REG1
XC62FP3302P
3 IN
OUT 1
K
+ C2
22/50
N.M.
HRW0202
+ C1
47/25
A2
D 102
+3.3V
G
A1
5
6
B
Sensor/Reset/Power supply block
A
N.M.
R174
0
R205
<DG>
<VBT>
DG
H
+24VA
+24VA
+5V
DG
DG
DG
VREF
+ C5
220/6.3
+3.3V
VBAT
+ C 13
100/50
C111
1
H
4/6
I
CNLIUA-14
CNCSW-2
CNPN-5
CNLIUA-13
(5-5B)
CNLIUA-12
I
1
2
3
4
5
6
UX-510UA
FO-1470U
6–5
1
2
3
4
5
R177
VO
R176
33K
IC10
HCT04
6Y 12
13 6A
(3-2A) PNLON
5Y 10
DG
E
Q102
C
B
+5V
R110
DG
B
4Y 8
9 4A
11 5A
(1-4A) START
B
470
R155
3Y 6
5 3A
(1-4A) CLK2
DG
0
L112
2Y 4
3 2A
(1-4A) CLK1
1
C223
270
GND 7
C184
N.M
C
N.M.
Q101
C166
C
470
C154
0.1
DG
C185
0.1
0
L116
N.M.
+24V
R154
E
DG
VG
+ C7
100/50
R152
R111
DG
VIDCNT1-A
(1-1A)
DG
BC3
NJM318
5
4 V–
(1-4A) CLK1
14 VCC
C182
0.1
6
–
8
V+ 7
BC2
IC 11
+
3
2
1 BC1
15P
R178
4.7K
270
22/50
R175
1K
C183
R218
1
C225
2
DG
3
R153
A
C8
DG
4
IC12
1Y 2
+5V
DG
VREF
E
<VO>
B
5
C226
1 1A
(4-5I)
+5V N.M.
CNCCD-1
GCONT
(3-5B)
R217
C
+
Q114
+5V
DG
ΦT
B
R106
0
N.M.
C165
ΦR
<VG>
DG
E
Q113
(CLK1)
Φ2
ΦT
ΦR
(CLK1)
Φ1
VG
VCCD
+5V
R167
+3.3V
+5V
R160
100
+5VPN
C
N.M.
C9
C224
1000P
+
6
C
D
D
DG
3
2
1
CNCCD-3
CNCCD-2
C194
IC7
DG
N.M
R187
CNPN-7
CNCCD-4
CNCCD-7
CNCCD-5
CNCCD-6
5
4
D104
1SS355
D103
1SS355
Video processing/Motor drive / Thermal block
B
DG
<VIN>
B
N.M.
THADI
(1-1F)
DG
E
C
E
R219
Q108
VTHON
(3-1A)
VIN
(1-1G)
E
DG
C193
+5V
(3-2A) LEDON
(1-1F) TPA
(1-1F) TPB
(1-1E) TPA
(1-1E) TPB
2
4
5
DG
GND
V+
IC6
MG
–
F
1
+ 3
B
DG
E
C
Q100
DTC143ZK
F
DG
R199
4
2
+3.3V
N.M.
MG
1SS355
1
3
MG
G
THG
R102
470K
R151
20K
OJE-SH-124M
RY1
7C 10
6C 11
5C 12
R139
22K
DG
MG
C125
0.1
0
L101
DG
+ C3
10/50
THG
C101
1
H
C4
100/50
DG
DG
C227
0.1
C153
C162
N.M.
THI
N.M.
THVDD
MG
MG
MG
VTH
VTH
VTH
+24V
LEDON
TPAD
TPAD
TPBD
VMT
VMT
4C 13
D100
KAB2402
TPBD
+24V
1N4748
D1
FU100
H
3C 14
2C 15
1C 16
COM 9
TD62001
+24V
E
7B
6B
5B
4B
3B
2B
1B
+3.3V
R197
8
7
6
5
4
3
2
1
IC 1
+24V
G
+
A
5/6
CNTH-5
CNTH-10
CNTH-9
CNTH-8
CNTH-7
I
CNTH-16
CNTH-2
CNTH-1
CNLED-1
CNLED-2
CNMT-4
CNMT-3
CNMT-2
CNMT-1
CNMT-6
CNMT-5
I
1
2
3
4
5
6
UX-510UA
FO-1470U
6–6
1
2
3
4
CNLIUA-3
N.M.
ZD101
CNLIUA-9
A
TELIN
DG
RXIN
TXOUT
TELOUT
N.M.
39K
R179
1
0.1
C189
R161
0
0.1
C188
R180
C171
R162
B
DG
184
100K
8
7
C
R185
220P
C
E
0
DG
C
Q104
RNC1402
0
0
L118
1
N.M.
C168
Q105
RNC1402
B
DG
B
0
R208
IC14
3
2
N.M.
R163
E
Q109
N.M.
C
0
C196
R182
4.7K
DG
+5VA
DG
C211
N.M.
4 DG
C206
R181
0
DG
C187
C10
C209
R183
11K
DG
IC 14
5
6
DG
+24VA
C210
0
0
+5VA
C186
0
ZD100
+5V
R207
C207
2
CNLIUA-8
CNLIUA-2
1
5
6
C213
E
DG
DG
B
R186
C190
1
R209
220P
D
C
DG
E
Q106
B
+5V
0
R210
SIGMUTE
(3-6A)
SIGTX
(3-3I)
0
C214
D
D105
1SS355
N.M.
DG
E
B
(3-4A)
RCVOL
E
DTMFMUTE
N.M.
CML
(3-2A)
SIGRX (3-4I)
C
Q107
(3-6A)
R211
1
C216
+5V
E
D106
1SS355
(3-1A)
VOLA
(3-1A)
VOLB
VOLC
(3-1A)
BZOUT1
(1-1F)
BZOUT2
(1-1F)
(3-3I)
SPOUT
(3-5A)
SPMUTE
RCVOL
(3-4A)
TELOUT1
(3-3I)
N.M.
F
F
B
C170
4700P
R168
20K
R169
0
L119
E
Q112
DG
C
B
E
C
DG
0.01
C169
1
Q111
R166
1K
DG
N.M.
3K
0
C219
R195
C191
B
G
E
Q110
100K
R164
43K
R196
DG
C
DG
IC 15
NJM2113
R190
100K
G
+
–
DG
R193
R192
R191
R194
C192
1
3
2
4
1
220K
R212
C218
220P
7
8
5
H
N.M.
DG
6
+5V
H
DG
2
–
Analog signal block
C
1
+
B
–
+
A
SP–
SP+
C11
47/25
I
CNSP-2
CNSP-1
I
6/6
1
2
3
4
5
6
UX-510UA
FO-1470U
UX-510UA
FO-1470U
Control PWB parts layout (Top side)
6–7
UX-510UA
FO-1470U
Control PWB parts layout (Bottom side)
6–8
6–9
1
CNHJ-3
CNHJ-2
CNHJ-1
CNHJ-4
TLJ-1
CNLNJ-5
CNLNJ-4
RX–
A
RX+
TX–
TX+
JP2
AR1
RA-391P
JP10
R137
0
N.M.
JP4
JP8
N.M.
L2A
L3
R-5C
JP9
JP11
JP12
N.M.
JP1
L7 R-5C
JP15
ARG
B
D4
DG
C9
22/50
DG
N.M.
C123
0.1
B
M
L8
JP16
C8
0.82
DG
+5V
C
R134
1K
ZD1
JUMPER
N.M.
R127
150
Q105
2SC2412K
N.M.
C122
R141
0
CML1
C13
22/50
N.M.
R142
D3
C
N.M.
VREF
N.M.
N.M.
L1
R-5C
C128
C129
DG
L5 R-5C
JP14
N.M.
DG
R128
1K
AR2
N.M.
VA2
ERZV5D471
C117
2200P
+5VA
R130
1.5K
R143
L6
C127
2200P
L4
R-5C
JP13
JP3
L2B
R-5C
N.M.
N.M.
JP17
L9 R-5C
C
R5
22K(1/2W)
R111
22K
JUMPER
R9
R8
ZD10
C119
1000P
D2
1SS133
2
3
4
5
CNLNJ-3
CNLNJ-2
TLJ-2
VA3
ERZV5D471
C116
R129
6
B
[2] TEL/LIU PWB circuit
A
DG
R126
C125
220P
C12
DG
N.M.
DG
–
~
IC102
2904
–
DG
5
6
R125 220K
+
DG
R136
3.3K
N.M.
C11
D101
DA204K
R135
10K
1
N.M.
ZD2
PC3
N.M.
C7
VA1
ZD8
N.M.
C115 220P
IC102
2904
7
C126
1000P
2 –
3
+
C124
0.01
ZD9
+
~
REC1
R119
C14
R7
JUMPER
C15
R6
D
R124
3.3K
N.M.
DG
ZD6
HZ27C
PC4
TLP521
N.M.
PC5
ZD11
D
R123
0
R131
8.2K
R132
39K
R104
3
4
E
C3
TELIN
DG
G
ZD3
TELMUTE
VREF
Q104
DTC143ZK
DG
F
PC1
S
Q1
CNLIUA-4
CNLIUA-3
CNLIUA-2
R2
D
R4
ZD5
HZ2C1
ZD4
HZ2C1
F
N.M.
R1
C6
22/50
VREF
DG
JP6
N.M.
C5
22/50
JP7
DG
C10
10/50
R140
0
+5VA
N.M.
R118
100
G
R138
20K
G
DG
R114
300
R116
620
R139
20K
+5V
R120
20K
C113
1
+5V
THESE MARKS ARE ALL SAFETY - CRITICAL PARTS.
TELOUT
N.M.
C111
NOTE:
ZD7
MTZJ5R1B
R103
PC2
T1
I2164
R133
0
1
2
E
C110
0.1
C112
820P
R115
47K
R112
20K
C106
1
C108
0.039
C4
4.7/50
N.M.
JP5
DG
4
+
–
5
6
8
R117
4.7K
H
DG
4
R108
3.3K
DG
C118
0.1
1
R110
R109
IC101
2904
IC101
2904
+
–
R113
15K
C109
33P
C104
IC101
2904
3
2
R107
N.M.
C107
DG
R121
1K
7
R122
86.6K
C114
33P
H
IC102
2904
8
CNLIUA-8
I
CNLIUA-9
+5VA
+5VA
+24VA
RXIN
N.M.
C105
TXOUT
1/2
I
1
2
3
4
5
6
UX-510UA
FO-1470U
6 – 10
1
2
3
4
5
6
B
A
+5V
K
A
+5V
R102
R101
DG
R3
E
PE1
C
B
SW1
HOOK SW
SW2
HOOK SW
TP1
DG
DG
N.M.
DPON
DOOR SW
RHS
PE1
HS
CI
DPMUTE
TP2
N.M.
N.M.
C103
DG
PC1
DG
C121
DG
PC5
C120
DG
DG
DG
Q101
Q103
PC4
TLP521
PC2
PC3
TEL/LIU PWB circuit
A
C
CNLIUA-11
CNLIUA-10
CNLIUA-1
CNLIUA-6
CNLIUA-5
N.M.
CNLIUB-2
CNLIUB-1
C
D
D
E
CNLIUA-14
CNLIUA-13
CNLIUA-12
E
+24V
DG
+5V
F
C2
22/50
C1
22/25
D1
1SS133
CML1
R106
100
R105
1K
F
DG
Q102
DTC143ZK
C102
0.1
C101
0.1
DG
CML
G
CNLIUA-7
+24VA
+5VA
G
H
H
I
2/2
I
1
2
3
4
5
6
UX-510UA
FO-1470U
UX-510UA
FO-1470U
TEL/LIU PWB parts layout (Top side)
6 – 11
UX-510UA
FO-1470U
TEL/LIU PWB parts layout (Bottom side)
6 – 12
6 – 13
1
2
3
4
5
6
B
A
N.M.
C1
0.1
L1
ELF15N005
C25
0.1
C15
1
CN1
3
V1
S07K150GA
R1
2.2M(1/2W)
F1
2.5A/125V
DS1
S1WB60
B
R9
470
Q3
2SC1741
C3
680P
C2
150/220
R10
0.15(1W)
R8
47K
N.M.
ZD1
Q1
FS5KM-14
R3
470K
R2
470K
[3] Power supply PWB circuit
A
C5
4700P
Q2
2SC4115
C4
R4
1500P 560
R24
100K
N.M.
C7
C26
3300P
D5
1SS355
D6
PC1
PC2501-1L
R7
180
R6
47K
R5
6.8K
C24
270P
C23
4700P
D
3
2
6
4
D
N.M.
C6
0Ω
D9
ERA22-06-V3
ZD6
JUMPER
C17
1000P
ZD2
RD4.3SB2
C
C
T1
PTTN117
12
11
10
9
D8
AK04-V0
C13
1500P
FB1
C10
330/16
OPTION
R18
3.3K
E
C8
330/35
PC1
PC2501-1L
D7
S3L20U
E
R15
330K
R14
1K
ZD5
RD6.2SB
Q4
2SC1740
R13
4.7K
F
C12
0.1
F
R17
8.2K
VR1
1K
R16
22K
IC1
UPC78M05
ZD4
RD30FB3
G
C16
0.1
FB2
JUMPER
FB1
BL02RN1
G
F3
CCP2E100
N.M.
ZD8
H
H
+5V
GND
6
GND
5
4
+24V
GND
3
+24V
CN2
2
1
I
I
1
2
3
4
5
6
UX-510UA
FO-1470U
UX-510UA
FO-1470U
Power supply PWB parts layout (Top side)
Power supply PWB parts layout (Bottom side)
C12
R16
R13
ZD5
R17
R18
R4
C24
R5
R6
ZD2
R15 R14
D5
R7
C6
C4
C17
ZD1
R9
ZD8
J14
D51
6 – 14
C
SH
DOS
SS
OS
3
2
6 – 15
D
OD
B
NS
4
A
RS
F2802XH-Z8
Φ2
1
E
NC
1
NC
Φ1
5V
NC
V0
F
NC
CCD PWB parts layout
F
NC
AG
22
NC
CN1-3
21
NC
2
20
NC
R1
2.2K
19
NC
C2
0.022
18
NC
VO
Q1
C1815
17
NC
CN1-1
C1
22/50
16
NC
IC1
TCD1208AP
E
15
NC
3
R2
39
D
14
+5V
ΦR
ΦT
Φ2
Φ1
C
13
CN1-2
CN1-7
CN1-4
CN1-5
CN1-6
[4] CCD PWB circuit
B
12
4
5
6
A
G
G
H
H
I
I
1
2
3
4
5
6
UX-510UA
FO-1470U
11
10
9
8
7
6
5
1
NC
6 – 16
C1
0.022
11
12
13
1
2
3
4
5
10
R4
100K
R11
1K
R10
6.2K
VO
R7
100K
R6
100K
R3
100K
R2
100K
R1
100K
7
4
1
COPY
D
CNLCD-6
CNLCD-5
CNLCD-3
CNLCD-2
CNLCD-1
A
B
C
D
NOTE: Since the parts of PWB cannot be supplied, change it as a unit.
C2
22/50
GND
8
16
VCC
A0
D1
A1
D2
A2
D3
A3
D4
D5
N.C
D6
D7
D8
D9
+5V
D5
1SS133
D4
1SS133
D3
1SS133
D2
1SS133
D1
1SS133
R5
100K
+5V
GND
GND
E
9
7
6
14
15
C5
0.022
IC1
74HC147
C3
0.022
KEN 1A
KEN 2A
KEN 3A
KEN 4A
C4
0.022
SEN4
RS
SEN3
LD7
SEN2
LD6
SEN1
LD5
SEN0
LD4
C
R8
100K
CNPN-7
CNPN-6
CNPN-5
CNPN-10
CNPN-4
CNPN-3
CNPN-2
CNPN-1
CNPN-11
CNLCD-4
CNPN-12
CNLCD-14
CNPN-13
CNLCD-13
CNPN-14
CNLCD-12
CNPN-15
CNLCD-11
[5] Operation panel PWB circuit
B
R9
100K
1
2
3
4
5
6
A
UP
2
5
8
0
DOWN
3
6
9
#
E
ORGSNS
SW-169-65AU
FRSNS
FRSNS
SW-169-62AU
ORGSNS
E
F
SHIFT
19
18
17
CNPN-9
CNPN-8
16
12
11
HOLD
SPEAKER
15
14
13
07
08
G
1
2
3
4
5
6
7
8
9
10
11
12
13
14
H
GND
+5V
VO
RS
R/W
E
N.C
N.C
N.C
N.C
LD4
LD5
LD6
LD7
CNLCD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
10
CNPN
KEN 4A
KEN 3A
KEN 2A
KEN 1A
GND
GND
+5V
ORGSNS
FRSNS
E
SEN4
SEN3
SEN2
SEN1
SEN0
09
05
06
04
REDIAL
03
02
01
START
SPEED
RESO
H
FUNCTION
STOP
G
MODE
MEMORY
F
I
I
1
2
3
4
5
6
UX-510UA
FO-1470U
UX-510UA
FO-1470U
CHAPTER 7. OPERATION FLOWCHART
[1] Protocol
Transmitter side
(Document inserted into
document sensor during
standby)
Receive side
G3 communication
CED
To recording
position
CED
NSF
NSF
CSI
CSI
DIS
DIS
TSI
Document inserted to
the reading position
TSI
(DCS)
NSS
NSS
(DCS)
TCF
TCF
CFR
IMAGE
SIGNAL
IMAGE
SIGNAL
CFR
1st page
RTC
RTC
Next page insert
command
Cut line printed
MPS
MPS
MCF
IMAGE
SIGNAL
IMAGE
SIGNAL
MCF
RTC
RTC
EOP
EOP
Cut line printed
MCF
MCF
DCN
DCN
Recording paper ejected
7–1
Document ejected
UX-510UA
FO-1470U
[2] Power on sequence
START
CPU initialized
MODEM initialized
“WAIT A MOMENT” display
STOP key ?
NO
“MEMORY CLEAR ?” display
NO
3 sec ?
YES
1
YES
STAND-BY
START key ?
NO
2
YES
COPY key ?
1
2
“MEMORY CLEARED” display
“MEMORY CLEARED” display
Memory clear
Memory clear
STAND-BY
PROCESS CHECK MODE
NO
YES
STOP key ?
NO
3 sec ?
NO
YES
STAND-BY
7–2
UX-510UA
FO-1470U
CHAPTER 8. OTHERS
[1] Service tools
1. List
NO.
PARTS CODE
DESCRIPTION
1
2
CPWBS2893SC02
UKOGM2057SCZZ
Q’TY
Extension board unit
Optical adjustment jig
1
1
PRICE
RANK
BZ
BR
Extension board unit
1
1
15
16
CNTH2(*1)
CNPN2
1
2
1
2
1
1
51
7
CNCCD2
CNSP2 CNCS2
1
21
6
CNLED2 CNMT2
8
CNPH2
CNSNS
1
4
2
CNBZ2
R1 1
A
K
E
C
PE
CNPH1
1
8
CNBZ1
4
1
HOOK SW
PIN
2
A
E
1
K
C
R3
36
DOOR SW
25
RBN
2
3
A
K
R2
14
E
C
1
1
1
R4
2
CNCS1
2
1
2
CNCCD1
CNLED1
1
1 7
2
CNMT1
1 6
1
CNSP1
CNPN1
15
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
CNTH1(*1)
1
PARTS CODE
QCNW–4723SCZZ
CCNW–4759SC01
QCNW–4725SCZZ
QCNW–4726SCZZ
QCNW–4727SCZZ
QCNW–4728SCZZ
QCNW–4729SCZZ
QCNW–4730SCZZ
QCNW–4731SCZZ
QCNW–4732SCZZ
QCNCM2401SC0B
QCNCM2442SC0B
QCNCM7014SC0B
QCNCM7014SC0E
QCNCM7014SC0F
QCNCM7014SC0G
QCNCM7014SC1E
QCNCM7014SC1F
QCNCM7014SC0D
QCNCM7014SC0H
VHPSG206S//-1
V R D - R C 2 EY 0 0 0 J
V R D – R C 2 EY 2 2 1 J
QSW-Z2206SCZZ
QSW-Z2226SCZZ
16
DESCRIPTION
CABLE [CNPN2]
CABLE [CNTH2]
CABLE [CNCCD2]
CABLE [CNMT2]
CABLE [CNLED2]
CABLE [CNSP2]
CABLE [CNCS2]
CABLE [CNSNS]
CABLE [CNPH2]
CABLE [CNBZ2]
CONNECTOR [CNSP1, CNSP2]
CONNECTOR [CNCS1, CNCS2]
CONNECTOR [CNLED1, CNLED2]
CONNECTOR [CNSES]
CONNECTOR [CNMT1, CNMT2]
CONNECTOR [CNCCD1, CNCCD2]
CONNECTOR [CNPN1, CNPN2]
CONNECTOR [CNTH1, CNTH2]
CONNECTOR [CNBZ1, 2]
CONNECTOR [CNPH1, 2]
PHOTO TRANSISTOR [P.E, RBN, PIN]
RESISTOR (1/4W 0Ω ±5%)[R4]
RESISTOR (1/4W 220Ω ±5%) [R1, R2, R3]
HOOK SWITCH
DOOR SWITCH
8–1
1
NOTE(*1): Mount connectors to
CNTH1 and CNTH2 in the reverse
direction against silk print of PWB.
Q’TY
1
1
1
1
1
1
1
1
1
1
2
2
2
1
2
2
2
2
2
2
3
1
3
1
1
PRICE
RANK
AL
AX
AH
AH
AF
AF
AF
AH
AN
AH
AA
AB
AD
AB
AB
AB
AC
AD
AB
AB
AG
AA
AA
AH
AG
UX-510UA
FO-1470U
2. Description
2-1. Extension board unit
1. Remove the TEL/LIU PWB, control PWB and Power Supply PWB
from this unit, and mount the extension board unit instead.
•
Before connecting the wiring to the extension board unit, set the
test PWB switches to the fixed position.
2. The setting is as follows.
A set with a mounted
extension board unit
Connector
Cable
Cable
Cable color
CNSNS
Connected to (PWB)
CNPN2
QCNW-4723SCZZ
1. Brown
CNTH2
CCNW-4759SC01
2. Red
DRSNS
DOOR SW (Control)
CNCCD2
QCNW-4725SCZZ
3. Orange
N.C.
—————
CNMT2
QCNW-4726SCZZ
4. Yellow
RBN
RBNSNS (Control)
CNLED2
QCNW-4727SCZZ
5. Green
PIN
PINSNS (Control)
CNSP2
QCNW-4728SCZZ
CNCS2
QCNW-4729SCZZ
CNPH2
QCNW-4731SCZZ
CNBZ2
QCNW-4732SCZZ
CNSNS
QCNW-4730SCZZ
RHS
TP2 (TEL/LIU)
The hook switch are operated by OR of the mechanical unit switch and
the test PWB switch. When performing installation in the machine unit,
set the test PWB switches to the fixed position.
Mechanical unit
CNPW
DOOR SW
1
CNLIUA
J17
J13
14
TP2
CHECK
TEL/LIU
PWB
RBNSNS
PWB to be tested
Actual operation with mechanical unit
POWER
SUPPLY
PWB
Hook SW
ON/OFF operation
ON-HOOK
PWB sensor check
Hook SW
ON-HOOK
ON/OFF operation
* Recording paper: ON
No recording paper: OFF
CNLIUA
PINSNS
DON'T SEPARATE
CHECK
CONTROL
PWB
UNIT
RELAY CABLE
Note: For the thermal head cable only, connect to the relay cable, not to
the relay PWB.
8–2
UX-510UA
FO-1470U
H Lightly loosen the red screws of the CCD PWB and obtain the VID
2-2. Scan optical system adjustment
signal waveform in synchronization with φT signal waveform. Adjust
the CCD PWB positioning to obtain the waveform as shown below.
(1) Outline
The adjustment procedures of the scan optical system are described
below:
Scan adjustment jig
(2) Adjustment procedures
1 Switch off the machine and disconnect the AC power cable from the
wall socket.
2 Fully open the upper cabinet, remove the fixing screws of the recording paper tray and remove the recording paper tray. In order to perform a focus adjustment, remove the optical system unit from the
frame.
3 Disconnect the main PWB from the TEL/LIU PWB.
4 Connect your oscilloscope channel 1 to the VIN signal and channel 2
of your oscilloscope to φT signal (Refer Pin 4 of connector CNCCD
on the main pwb). Connect the earth clips of either probe to AG ground
as shown. Set the trigger to channel 2.
Optical system
unit
Reference surface
VIN
(CH1)
1V/DIV
øT
(CH2)
CNCCD
Rø T
1.89msec
0.5msec/DIV
VIN
VO CNCCD-3 (CCD source output)
øT CNCCD-6 (Line sync signal)
VG CNCCD-5 (Ground)
*2:White level
5 Re-connect the main PWB to the TEL/LIU PWB and connect these
circuit boards to the connectors on the chassis.
6 Re-assemble up to and including the recording paper tray to the main
chassis and close upper cabinet.
7 Plug the AC power cable into the wall outlet and turn the fax machine
on.
8 Insert a test chart in the document hopper and execute the CCD
*1: Difference
*1: Increase the difference
by focus adjustment.
*2: Adjust as shown by
CCD PWB adjustment.
*2: Black level
[CCD waveform model]
CCD waveform
I After completing the CCD adjustment, tighten the two red screws on
Adjust Mode diagnostic. Press the START key to enable local copy
until approximately one fifth of the page has been copied, then press
the STOP key to enable the CPU wait state.
the CCD pwb and apply screw locking material to prevent the CCD
pwb from moving.
9 Fully open the upper cabinet and remove the recording paper tray.
F Install the scan adjustment jig to the optical system unit, so that the
pattern surface is on the lower side.
G Fit the pins of the scan adjustment jig to the holes of the optical sys-
J Assemble the recording paper tray and fixing screws.
tem frame.
8–3
UX-510UA
FO-1470U
[2] IC signal name
CONTROL PWB UNIT
IC1: VHiTD62001AP1 (TD62001AP)
IC8: VHiW24258S7LE (W24258S-70LE)
(TOP VIEW)
O1 O2 O3 O4 O5 O6 O7 COM
16 15 14 13 12 11 10 9
A14
1
28 VDD
A12
2
27 WE
A7
3
26 A13
A6
4
25 A8
A5
5
24 A9
A4
6
23 A11
A3
7
22 CS2/OE
A2
8
21 A10
Pin name
Signal
20 CS1
A0~A14
CS1/CS2
Address input
A1
1
I1
2
I2
3
I3
4
I4
5
I5
6
I6
7
8
I7 GND
9
A0 10
19 IO8
IO1 11
18 IO7
IO2 12
17 IO6
IO3 13
16 IO5
VSS 14
15 IO4
WE
OE
I/O1~I/O8
Chip enable
Write enable
Write enable
Data I/O
VDD
Power source
VSS
Ground
IC15: VHiNJM2113M-1 (NJM2113M)
IC4: VHi27L20012MX (27L2000)
CD
1
8
VO2
FC2
2
7
GND
FC1
3
6
VCC
VIN
4
5
VO1
VPP
A16
A15
A12
A7
A6
A5
A4
A3
A2
A1
A0
Q0
Q1
Q2
GND
(TOP VIEW)
IC5: RH-iX2168SCZZ (MSM51V4800E)
28 VSS
DQ1 2
27 DQ8
DQ2 3
26 DQ7
DQ3 4
25 DQ6
17 A5
A3 13
16 A4
WE 7
RAS 8
A9R 9
VCC 14
SIGNAL
ADDRESS INPUT
DATA INPUT/OUTPUT
CHIP ENABLE INPUT
OUTPUT ENABLE INPUT
PROGRAMMABLE ENABLE INPUT
PROGRAM SUPPLY VOLTAGE
NO INTERNAL CONNECTION
POWER SUPPLY PIN (+5V)
GROUND PIN
IC13: VHiSCE114//-1 (20415)
SIGNAL
ADDRESS INPUT
ROW ADDRESS STROBE
COLUMN ADDRESS STROBE
DATA INPUT/OUTPUT
OUTPUT ENABLE
WRITE ENABLE
POWER SUPPLY (+3.3V)
GROUND
NO INTERNAL CONNECTION
CTRLSIN
Reserved
Reserved
SOUT
SIN
FSYNC
POR
AVSS
1
2
3
4
5
6
7
8
24
23
22
21
20
19
18
17
AVSS
AVDD
AGND
VREF
MICBIAS
MICIN–
MICIN+
LINEIN
18 A6
A2 12
NC 6
PIN NAME
A0~A17
Q0~Q7
CE
OE
PGM
VPP
NC
VCC
GND
16
15
14
13
12
11
10
9
A1 11
DQ4 5
VCC
PGM
A17
A14
A13
A8
A9
A11
OE
A10
CE
Q7
Q6
Q5
Q4
Q3
25
26
27
28
29
30
31
32
A0 10
PIN NAME
A0~A8, A9R
24 DQ5
RAS
23 CAS CAS
DQ1~DQ8
22 OE
OE
21 NC WE
VCC
20 A8
VSS
NC
19 A7
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
NC
ICLK
NC
NC
NC
NC
MCLK
NC
VCC 1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
15 VSS
8–4
MODE0
MODE1
Reserved
DVDD
DVSS
SPKRO–
SPKRO+
LINEO
UX-510UA
FO-1470U
IC9: VHiSCE114//-1 (SCE114)
GPIO[31]
GPIO[32]
GPIO[33]
GPIO[34]
GPIO[35]
GPIO[36]
VDD
GPIO[0]/SR4IN
GPO[31]/SR3OUT
GPIO[37]/IRQ15N
IARESET
IACLK/DSPCSN
IA1CLK
SR3IN/DSPIRQN
SR4OUT
SR1IO
SA1CLK
VSSPLL
TSTCLK
DEBUGN
RDN
WRN
SYNC/GPO[20]
ROMCSN
CS1N/GPO[21]
VSS
SXIN
SXOUT
VDD
PM[3]/GPO[3]
PM[2]/GPO[2]
PM[1]/GPO[1]
PM[0]/GPO[0]
SM[3]/GPO[7]
SM[2]/GPO[6]
SM[1]/GPO[5]
SM[0]/GPO[4]
REGDMA/GPO[18]
WAITN/GPO[19]
VDDPLL
D[7]
D[6]
D[5]
D[4]
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
VSS
D[3]
D[2]
D[1]
D[0]
A[23]/EYEXY
A[22]/EYESYNC
A[21]/EYECLK
A[20]
A[19]
A[18]
VDD
A[17]
A[16]
A[15]
A[14]
VSS
A[13]
A[12]
A[11]
A[10]
A[9]
A[8]
A[7]
A[6]
A[5]
A[4]
VDD
A[3]
A[2]
A[1]
A[0]
GPIO[20]/ALTTONE
NC
NC
NC
NC
NC
GPIO[19]/RDY/SEROUT
GPIO[11]/BE/SERINP
VSS
PCLK/DMAACK
PDAT
PLAT
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
132
131
130
129
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
VREFP
ADXG
ADVA
ADGA
VIN
VREFN/CLREF
ADGA
NC
PWRDWNN
INTPWRDWNEN
BATRSTN
TEST[0]
TEST[1]
CS0N
WRPROTN
XOUT
XIN
VBAT
DWRN
CAS[0]N
CAS[1]N
RASN
VDRAM
GPIO[10]/SSSTAT2
GPIO[5]/SSCLK2
GPIO[6]/SSTXD2
GPIO[7]/SSRXD2
LCDCS/GPO[17]
NC
LEDCTRL/GPO[16]
VSS
GPIO[4]/CPCIN
GPIO[12]/CS[2]N
GPIO[13]/CS[3]N
GPIO[14]/CS[4]N
GPIO[15]/CS[5]N
GPIO[16]/IRQ[8]
GPIO[17]
VDD
STRBPOL/DMAREQ
STRB[0]
STRB[1]
STRB[2]
STRB[3]
8–5
GPIO[30]
GPIO[29]
GPO[30]
GPO[29]
GPO[28]
GPO[27]
GPO[26]
GPIO[28]
GPIO[27]
GPIO[26]
GPIO[25]
VSS
TONE
VDD
START
CLK1
CLK1N/GPO[25]
CLK2/GPO[24]
FCSN[1]/VIDCTL[0]/GPO[23]
FCSN[2]/VIDCTL[1]/GPO[22]
PGIO[8]/FWRN
PGIO[9]/FRDN
PGIO[1]/SASTXD
PGIO[2]/SASRXD
PGIO[3]/SASCLK
PGIO[18]/IRQ[9]N
VSS
RESETN
OPI[0]/GPIO[21]/SSRXD1
OPI[1]/GPIO[22]/SSSTAT1
OPI[2]/GPIO[23]/SSCLK1
OPI[3]/GPIO[24]
OPO[0]/GPO[8]/SMPWRCTRL
OPO[1]/GPO[9]/PMPWRCTRL
OPO[2]/GPO[10]/RINGER
OPO[3]/GPO[11]
OPO[4]/GPO[12]/SSTXD1
OPO[5]/GPO[13]
OPO[6]/GPO[14]
OPO[7]/GPO[15]
THADI
VDD
VREFP
VREFN
UX-510UA
FO-1470U
[3] Changing the record paper size
How to change the A4 size and letter size of the record papers
1) It becomes the record paper of the A4 size by installing A4 paper guide (PGiDM2493XHSA)
which shows in the drawing. Remove A4 guide when you use the record paper of the letter size.
A4 paper guide
PGiDM2493XHSA
Screw
XEBSD30P10000
RP hopper
2) Set soft switch SW-L2 No.1 and the initialization of SW-L2 No.2 as follows.
SW
NO.
DATA
NO.
Switch setting and function
ITEM
1
Paper set size
SW
l
L2
1
2
No. 1
No. 2
8–6
Initial
setting
0
LETTER
LEGAL
A4
0
0
0
1
1
0
Remarks
OPTION
0
0
UX-510UA
FO-1470U
PARTS GUIDE
UX-510A
MODEL FO-1470
SELECTION CODE
U
DESTINATION
U.S.A.
CONTENTS
1
Cabinet, etc.
7
Packing material & Accessories
2
Upper cabinet
8
Control PWB unit
3
Document guide upper
9
TEL/LIU PWB unit
4
Optical unit
10 Power supply PWB unit
5
Drive unit
11 Operation panel PWB unit
6
Head unit
Index
Because parts marked with " " are indispensable for the machine safety maintenance and operation, it must be
replaced with the parts specific to the product specification.
UX-510UA
FO-1470U
[1] Cabinet, etc.
22
99
25
1
2
23
24
81
B7
53
66
HEAD
UNIT
26
67
27
B2
74
B2
81
72
58
B11
68
53
B2
DOCUMENT
GUIDE
UPPER
54
46
B2
2
B11
B3
70
50
95 B2
71
77
90
B11
B2
B2
73
52
B2
45
76
37
34
51
41
B3
43
39
36
40
86
B2
B2
31
14
B2
28
W2
65
62
55
61
TEL/LIU
ARG
CABLE
B2 32
B4
64
59
B5
B2
5
B2
B2
20
B2
B2
6
7
B2
33
38
11
63
57
38
7
60
87
B2
B2
10
63
W1
12
7
78
42
30
29 35
8
69
HEAD
EARTH
CABLE
9
B2
98
B2
21
4
B2
B11
DRIVE
UNIT
B3
97
3
B10
80
B10
17
18
19
15
94
75
17
93
18
79
14
13
100mm
OPTICAL UNIT
–1–
84
(BLACK)
UX-510UA
FO-1470U
PARTS CODE
NO.
PRICE
RANK
NEW
MARK
PART
RANK
BH
AT
AK
AK
BU
BC
AK
AC
AD
AC
AP
AM
AP
AG
AA
AE
AZ
AL
AC
AC
AD
AP
BF
AP
AG
AB
AD
AE
AC
AE
AC
AD
AX
AD
AP
AF
AD
AD
AD
AC
AB
AC
AC
AE
AK
AD
AD
AH
AN
AK
AD
AE
AK
AC
AC
AC
AE
AS
AP
AB
AC
AD
AD
AK
AC
AQ
AG
AC
AD
AC
AD
AD
AF
AM
AE
AB
AH
AL
AK
AE
N
N
N
N
N
N
E
E
C
C
E
E
C
C
C
C
C
C
C
C
C
B
D
D
C
C
C
B
E
C
C
C
C
C
C
C
C
D
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
D
D
C
C
DESCRIPTION
[1] Cabinet,etc.
1
2
3
4
5
6
7
8
9
10
11
12
!
!
!
13
14
15
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
45
46
50
51
52
53
54
55
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
DCEKP264CXH01
DCEKP264CXH02
QCNW-390AXHZZ
CCNW-391AXH01
DCEKC281PXHZZ
DCEKL266CXH01
CGERH2363AX01
LBSHP2088AXZZ
MLEVP2253XHYA
NGERH2275XHZZ
NROLR2333XHZZ
NROLR2467XHZZ
PGIDM2481XHYA
PGIDM2481XHYB
LBNDJ2006XHZZ
RCORF2125XHZZ
GCABB2290XHAA
GCABB2290XHAB
MSPRC3039XHFJ
NROLP2334XHZA
NSFTZ2281XHZZ
QACCD2054XHZZ
RDENT2157XHZZ
GCOVA2376XHYA
GCOVA2376XHYB
MSPRC3249XHZZ
NGERP2318XHZZ
PGIDM2483XHYA
PGIDM2483XHYB
PGIDM2484XHYA
PGIDM2484XHYB
TLABH4161AXZZ
LFRM-2180XHAZ
LPLTM2791AXFW
LPLTP2884AXZZ
LSTPP2044XHZZ
MLEVP2249XHYZ
MLEVP2252XHYZ
MLEVP2258XHYZ
MSPRC2999XHFJ
MSPRC3247XHZZ
MSPRC2927AXFJ
MSPRD2929AXFJ
NGERH2310XHZZ
NSFTM2280AXZZ
PFLT-2009AXZZ
PSHEZ3344AXZZ
PSHEZ3293AXZZ
CROLR2362AX01
CROLR2363XH02
NGERH2359AXZZ
NSFTM2268XHYZ
PGIDM2479XHYA
LBSHP2086AXZZ
NGERH2309XHZZ
NGERH2358AXZZ
NGERH2361AXZZ
NROLR2468XHZZ
CGERH2314AX51
MSPRD3250XHZZ
NGERH2279XHZZ
NGERH2367AXZZ
NROLP2332XHZZ
NSFTM2279AXZZ
PGIDM2485XHYA
LPLTM2924XHFW
LPLTP2888XHYA
LPLTP2888XHYB
MSPRC2926AXFJ
MSPRT2932AXFJ
NGERH2365AXZZ
NGERH2366AXZZ
PGIDM2480XHYA
PHOP-2095XHYA
PHOP-2095XHYB
PSEL-2015SCZZ
GCABC2291XHYA
GCABC2291XHYB
GCOVA2375XHYZ
GCOVA2378AXZZ
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
Operation panel unit
Operation panel unit
Panel cable
Speaker ass’y
Control PWB unit(Within ROM)
TEL/LIU PWB unit
Feed gear ass’y
Transfer bearing
Hook switch lever
Transfer gear 2
Paper feed roller
Transfer roller
Document guide lower
Document guide lower
Band(100mm)
Core(TRA31)
Lower cabinet
Lower cabinet
Pinch roller spring 2
Pinch roller
Pinch roller shaft
AC cord
Power supply PWB unit
Top cover
Top cover
Hopper spring
Pinion gear
Hopper guide,left
Hopper guide,left
Hopper guide,right
Hopper guide,right
Imaging film set label
Main frame
Hold down plate B
Separate plate
Back tention stopper
P-IN sensor lever
Film sensor lever
Cover switch lever
Back tention spring
Separate plate spring
Pop up spring
Sensor lever spring
Back tension gear
Film guide shaft B
Back tension felt
Separate sheet
Separate plate sheet
PU roller ass’y
PO roller ass’y
PO gear
PU roller shaft
U turn guide
Platen bearing
Platen gear
PU gear
Reduction gear A
Platen roller
Slip gear ass’y
PO pinch roller spring
Idler gear A
Take-up gear
PO pinch roller
Film shaft C
PO guide
Paper up plate
RP release plate
RP release plate
Cassette spring
RP release spring
RP release gear,left
RP release gear,right
Paper guide
RP hopper
RP hopper
RP pad
Rear cabinet
Rear cabinet
ROM cover
Memory cover
–2–
[510UA]
[1470U]
[510UA]
[1470U]
[510UA]
[1470U]
[510UA]
[1470U]
[510UA]
[1470U]
[510UA]
[1470U]
[510UA]
[1470U]
[510UA]
[1470U]
[510UA]
[1470U]
UX-510UA
FO-1470U
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
AE
AC
AB
AE
AA
AC
AC
AE
AP
AD
AD
AD
AC
AG
AC
AA
AC
AA
AA
AB
AA
AA
AB
AB
N
C
C
C
C
C
C
DESCRIPTION
[1] Cabinet,etc.
78
79
80
81
84
86
87
90
93
94
95
97
98
99
B2
B3
B4
B5
B7
B10
B11
W1
W2
PCOVA2114XHYZ
GLEGG2063AXZZ
PSHEZ3563XHZZ
PSHEZ3332AXZZ
LBNDJ2008SCZZ
PSHEZ3341AXZZ
PSHEZ3342AXZZ
PCUSG2112XHZZ
LPLTP2968XHZZ
NROLP2396XHZZ
PCUSS2114XHZZ
LPLTM3122XHZZ
MSPRP3123XHZZ
HPNLH2405XHSA
HPNLH2405XHSB
XEBSD30P10000
LX-BZ2222AXZZ
XBPSD30P06K00
XBPSN40P06K00
LX-BZ2138XHZZ
XEBSE30P10000
XEBSF30P12000
LX-WZ2228XHZZ
LX-WZ2246XHZZ
N
N
N
N
C
C
C
C
C
C
D
D
C
C
C
C
C
C
C
C
C
Side cover
Rubber leg
Jack sheet
Hopper sheet
Band(Black)
Guide sheet, left
Guide sheet, right
PO gear cushion
Document kick plate
Document kick roller
PO cushion
Earth plate
Speaker holder spring
Decoration panel
Decoration panel
Screw(3x10)
Screw
Screw(3x6)
Screw(4x6)
Screw(3x6)
Screw(3x10)
Screw(3x12)
Cut washer
Washer
–3–
[510UA]
[1470U]
UX-510UA
FO-1470U
[2] Upper cabinet
901
7
3
4
5
6
1
11
B1
9
2
8
B1
B1
PARTS CODE
NO.
PRICE
RANK
NEW
MARK
PART
RANK
BF
AR
AE
AH
AG
AF
AF
AE
AD
AD
AD
AE
AC
AD
AH
AE
AK
AA
N
N
N
N
E
D
D
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
Operation panel PWB unit(Without sensor)
Upper cabinet
Upper cabinet
12 key
12 key
Direct key
Direct key
Start key
Start key
Stop key
Stop key
Mode key
Mode key
Insulation sheet
FRSNS sensor
ORGSNS sensor
Panel cable
Screw(2x6)
BH
AT
N
N
E
E
Operation panel unit
Operation panel unit
10
DESCRIPTION
[2] Upper cabinet
1
2
3
4
5
6
7
8
9
10
11
B1
901
DCEKP351BXH02
GCABA2289XHYA
GCABA2289XHYB
JBTN-2202XHYA
JBTN-2202AXSC
JBTN-2203XHYA
JBTN-2203AXSC
JBTN-2204XHYA
JBTN-2204AXSB
JBTN-2205XHYA
JBTN-2205AXSB
JBTN-2206XHYA
JBTN-2206XHYB
PSHEZ3291AXZZ
QSW-M2246AXZZ
QSW-M2247AXZA
QCNW-390AXHZZ
XEBSD20P06000
(Unit)
DCEKP264CXH01
DCEKP264CXH02
N
N
N
N
N
N
–4–
[510UA]
[1470U]
[510UA]
[1470U]
[510UA]
[1470U]
[510UA]
[1470U]
[510UA]
[1470U]
[510UA]
[1470U]
[FRSNS]
[ORGNSN]
[510UA]
[1470U]
UX-510UA
FO-1470U
[3] Document guide upper
4
12
4
2
14
7
1
17
5
17
6
8
15
13
8
10
3
11
16
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
DESCRIPTION
[3] Document guide upper
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
LPLTG2707XHZZ
LPLTP2790XHZZ
MLEVP2257XHZA
MSPRC2924AXFJ
MSPRD3197XHZZ
MSPRT2923AXFJ
MSPRT3235XHZZ
NBRGP2141AXZZ
NGERH2275XHZZ
NGERH2317XHZZ
NGERH2356XHZZ
NROLP2334XHZA
NROLR2466XHZZ
NSFTZ2257AXZZ
PGIDM2482XHAZ
PSHEZ3290AXZZ
MARMP2026XHZZ
AE
AD
AC
AC
AD
AC
AB
AC
AC
AC
AC
AC
AK
AE
AM
AD
AC
N
N
N
N
N
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
9
Separation rubber
Separate plate
Panel lock lever
Pinch roller spring
Paper feed spring
Panel lock lever spring
Separate spring
Transfer bearing
Transfer gear 2
Idler gear,28Z
Idler gear,20Z
Pinch roller
Transfer roller
Pinch roller shaft
Document guide upper
Rear sheet
Paper feed arm
–5–
UX-510UA
FO-1470U
[4] Optical unit
12
5
10
3
14
12
B8
6
1
13
901
15
15
4
2
9
17
7
8
17
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
DESCRIPTION
[4] Optical unit
1
2
3
4
5
6
7
8
9
10
12
13
14
15
17
B8
901
DCEKD475AAX05
LFRM-2164XHAA
MSPRP2817SCZZ
PFLT-2006XHZZ
PGLSP2058XHZZ
PLNS-2049XHZZ
PMIR-2070XHZZ
PMIR-2071XHZZ
PMIR-2072XHZZ
PSHEZ3196AXZZ
PSHEZ3258AXZZ
QCNW-395AXHZZ
VHPSNK15A24-1
PCUSS2124XHZZ
PSHEP3606XHZZ
LX-BZ2182SCZZ
(Unit)
DCYOD475AXH03
BE
AF
AC
AA
AE
AZ
AG
AH
AH
AC
AD
AD
AZ
AA
AA
AB
BN
N
N
N
N
N
B8
E
C
C
C
C
C
C
C
C
C
C
C
B
C
C
C
CCD PWB unit
Optical frame
Lens holding spring
Felt
Reader glass
Lens
Mirror 1
Mirror 2
Mirror 3
Shading sheet
Shading sheet 3
LED cable
LED
Cushion,optical frame
Mirror sheet 2
Screw
E
Optical unit
–6–
UX-510UA
FO-1470U
[5] Drive unit
B2
B2
14
5
4
15
16
3
12
13
9
8
7
10
2
6
1
11
11
9
17
Cut after insert must be
touch to the bottom.
PARTS CODE
NO.
PRICE
RANK
NEW
MARK
PART
RANK
DESCRIPTION
[5] Drive unit
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
B2
CLEVP2254AX01
CLEVP2255AX01
CLEVP2256AX01
LFRM-2181AXZZ
LPLTM2886AXFW
MCAMP2023AXZZ
MSPRD2962AXFJ
NGERH2279XHZZ
NGERH2281XHZZ
NGERH2361AXZZ
NGERH2362AXZZ
QCNW-394AXHZZ
QSW-F2224SCZZ
RMOTZ2161XHZZ
NGERH2360AXZZ
PCUSG2111XHZZ
LBNDJ2006XHZZ
XEBSD30P10000
AE
AE
AE
AV
AQ
AD
AC
AC
AD
AE
AE
AD
AE
AX
AE
AE
AA
AA
N
N
C
C
C
C
C
C
C
C
C
C
C
C
C
B
C
C
C
C
Planet lever A ass’y
Planet lever B ass’y
Planet lever C ass’y
Drive unit frame
Motor heat sink
Cam A
Cam hold spring
Idler gear A
Idler gear C
Reduction gear A
Reduction gear C
Cam switch cable
Cam switch
Motor
Reduction gear B
Cushion
Band
Screw(3x10)
–7–
UX-510UA
FO-1470U
[6] Head unit
1
W1
6
4
16
B6
9
5
3
15
17
5
16
B6
7
13
10
B2
12 17 14
11
8
2 (100mm)
PARTS CODE
NO.
PRICE
RANK
NEW
MARK
PART
RANK
AD
AC
AA
AK
AD
AD
AC
AC
AH
AN
AD
AE
AM
AE
BQ
AE
AD
AD
AA
AA
AB
N
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
C
C
C
C
C
C
DESCRIPTION
[6] Head unit
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
B2
B6
W1
JKNBP2074XHYA
JKNBP2074XHYB
LBNDJ2006XHZZ
LFRM-2179XHZA
MLEVP2248AXZZ
MSPRC2964AXFJ
MSPRC2920AXFJ
MSPRC2928AXFJ
NSFTM2278AXZZ
PGIDM2519XHZL
PGIDM2478AXZR
PSHEZ3292AXZZ
QCNW-392AXHZZ
QCNW-393AXHZZ
RHEDZ2063XHZZ
MSPRC3210XHZZ
MSPRC3212XHZZ
PSHEZ3366XHZZ
XEBSD30P10000
XBBSD30P06000
LX-WZ2228AXZZ
N
N
N
N
N
N
Release knob
Release knob
Band(100mm)
Head frame
Lock lever
Head spring B
Lock spring
Pop up spring
Film guide shaft
Head guide,left
Head guide,right
Head guide sheet
Head cable
Head earth cable
Termal head
Head spring 1
Head spring 2
Head sheet
Screw(3x10)
Screw(3x6)
Cut washer
–8–
[510UA]
[1470U]
UX-510UA
FO-1470U
[7] Packing material & Accessories
4
7
TAPE
TAPE
1
TAPE
5
3
6
12
2
Turn
Over
13
15 10
16
13
13
9
17
14
TAPE
18
11
19
PARTS CODE
NO.
PRICE
RANK
NEW
MARK
PART
RANK
AN
AM
AE
AM
AE
AE
AL
AC
AK
AL
AD
AX
AP
AG
AG
AC
AC
AE
AV
AE
AG
AC
AC
AG
AK
N
N
N
N
N
N
D
C
C
C
C
C
C
D
D
D
D
E
E
C
C
D
C
C
S
C
D
D
D
D
D
DESCRIPTION
[7] Packing material & Accessories
1
2
3
4
5
6
7
9
!
!
!
10
11
12
13
14
15
16
17
18
19
TCADZ3055XHZZ
LPLTP2889XHYA
LPLTP2889XHYB
LPLTP2890XHYA
LPLTP2890XHYB
PCOVA2115XHSB
PCOVA2115XHSA
SPAKA328CXHZZ
TINSE4157XHTZ
TINSE4162XHTZ
TLABH276CXHZZ
DUNTK464BXHFW
DUNTK464BXHOG
QCNW-289ASCOW
QCNW-289ASCOG
SPAKA213AAXZZ
LBSHP2078XHZZ
NGERH2315XHZZ
PRBNN2009SCZZ
QCNW-290ASCZZ
SPAKP4381AXZZ
SPAKA261CXHZZ
SPAKA262CXHZZ
SPAKC263CXHZZ
SPAKC300CXHTZ
N
N
N
N
N
N
N
N
N
Pop card
Paper tray A
Paper tray A
Paper tray B
Paper tray B
Paper tray cover
Paper tray cover
Protection pad,paper tray
Operation manual
Operation manual
Rapid key labels
Handset
Handset
Handset cord
Handset cord
Protection sheet
Imaging film frange
Imaging film gear
Imaging film(Initial starter film 20m)
Telephone line cord
Vinyl cover
Packing add.,left
Packing add.,right
Packing case
Packing case
–9–
[510UA]
[1470U]
[510UA]
[1470U]
[510UA]
[1470U]
[510UA]
[1470U]
[510UA]
[1470U]
[510UA]
[1470U]
[510UA]
[1470U]
UX-510UA
FO-1470U
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
DESCRIPTION
[8] Control PWB unit
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
UBATL2049SCZZ
VCEAGA1EW476M
VCEAGA1HW226M
VCEAGA1HW106M
VCEAGA1HW107M
VCEAGA0JW227M
VCEAGA0JW227M
VCEAGA1HW107M
VCEAGA1HW226M
VCEAGA1EW476M
VCEAGA1HW106M
VCEAGA1HW107M
VCEAGA1HW106M
VCEAGA1HW106M
VCKYCY1EF104Z
VCKYCY1AF105Z
VCKYCY1AF105Z
VCKYTV1HF104Z
VCCCCY1HH101J
VCCCCY1HH101J
VCKYCY1HB102K
VCKYCY1HB102K
VCKYCY1AF105Z
VCKYCY1HB102K
VCKYCY1HB102K
VCKYTV1CF225Z
VCCCCY1HH180J
VCCCCY1HH330J
VCKYCY1AF105Z
VCKYCY1AF105Z
VCKYTV1HF104Z
VCKYCY1EF104Z
VCKYCY1AF105Z
VCKYCY1AF105Z
VCKYCY1EF104Z
VCKYCY1AF105Z
VCKYCY1HB102K
VCKYCY1HB102K
VCKYCY1HB102K
VCKYTV1CF225Z
VCKYCY1EF104Z
VCKYCY1AF105Z
VCKYCY1AF105Z
VCKYCY1AF105Z
VCKYCY1AF105Z
VCKYCY1AF105Z
VCKYTV1CF225Z
VCKYCY1AF105Z
VCKYCY1HB102K
VCCCCY1HH101J
VCKYTV1CF225Z
VCKYTV1CF225Z
VCKYCY1HB102K
VCKYCY1HB102K
VCKYCY1HB102K
VCKYCY1HB102K
VCCCCY1HH101J
VCKYCY1EF104Z
VCKYTV1CF225Z
VCKYTV1CF225Z
VCKYTV1CF225Z
VCKYTV1CF225Z
VCKYTV1CF225Z
VCCCCY1HH101J
VCCCCY1HH101J
VRS-CY1JB000J
VCKYCY1HB103K
VCKYCY1HB472K
VCKYCY1AF105Z
VCCCCY1HH150J
VCCCCY1HH150J
VCKYCY1EF104Z
VCCCCY1HH101J
VCCCCY1HH101J
VCCCCY1HH101J
VCCCCY1HH101J
VCKYCY1EF104Z
VCCCCY1HH150J
VCKYTV1HF104Z
VRS-CY1JB000J
AF
AA
AB
AA
AA
AD
AD
AA
AB
AA
AA
AA
AA
AA
AA
AC
AC
AA
AA
AA
AA
AA
AC
AA
AA
AD
AA
AA
AC
AC
AA
AA
AC
AC
AA
AC
AA
AA
AA
AD
AA
AC
AC
AC
AC
AC
AD
AC
AA
AA
AD
AD
AA
AA
AA
AA
AA
AA
AD
AD
AD
AD
AD
AA
AA
AA
AA
AA
AC
AB
AB
AA
AA
AA
AA
AA
AA
AB
AA
AA
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
Battery(CR2032T23)
Capacitor(25WV 47µF)
Capacitor(50WV 22µF)
Capacitor(50WV 10µF)
Capacitor(50WV 100µF)
Capacitor(6.3WV 220µF)
Capacitor(6.3WV 220µF)
Capacitor(50WV 100µF)
Capacitor(50WV 22µF)
Capacitor(25WV 47µF)
Capacitor(50WV 10µF)
Capacitor(50WV 100µF)
Capacitor(50WV 10µF)
Capacitor(50WV 10µF)
Capacitor(25WV 0.1µF)
Capacitor(10WV 1µF)
Capacitor(10WV 1µF)
Capacitor(50WV 0.1µF)
Capacitor(50WV 100PF)
Capacitor(50WV 100PF)
Capacitor(50WV 1000PF)
Capacitor(50WV 1000PF)
Capacitor(10WV 1µF)
Capacitor(50WV 1000PF)
Capacitor(50WV 1000PF)
Capacitor(16WV 2.2µF)
Capacitor(50WV 18PF)
Capacitor(50WV 33PF)
Capacitor(10WV 1µF)
Capacitor(10WV 1µF)
Capacitor(50WV 0.1µF)
Capacitor(25WV 0.1µF)
Capacitor(10WV 1µF)
Capacitor(10WV 1µF)
Capacitor(25WV 0.1µF)
Capacitor(10WV 1µF)
Capacitor(50WV 1000PF)
Capacitor(50WV 1000PF)
Capacitor(50WV 1000PF)
Capacitor(16WV 2.2µF)
Capacitor(25WV 0.1µF)
Capacitor(10WV 1µF)
Capacitor(10WV 1µF)
Capacitor(10WV 1µF)
Capacitor(10WV 1µF)
Capacitor(10WV 1µF)
Capacitor(16WV 2.2µF)
Capacitor(10WV 1µF)
Capacitor(50WV 1000PF)
Capacitor(50WV 100PF)
Capacitor(16WV 2.2µF)
Capacitor(16WV 2.2µF)
Capacitor(50WV 1000PF)
Capacitor(50WV 1000PF)
Capacitor(50WV 1000PF)
Capacitor(50WV 1000PF)
Capacitor(50WV 100PF)
Capacitor(25WV 0.1µF)
Capacitor(16WV 2.2µF)
Capacitor(16WV 2.2µF)
Capacitor(16WV 2.2µF)
Capacitor(16WV 2.2µF)
Capacitor(16WV 2.2µF)
Capacitor(50WV 100PF)
Capacitor(50WV 100PF)
Resistor(1/16W 0Ω ±5%)
Capacitor(50WV 0.01µF)
Capacitor(50WV 4700PF)
Capacitor(10WV 1µF)
Capacitor(50WV 15PF)
Capacitor(50WV 15PF)
Capacitor(25WV 0.1µF)
Capacitor(50WV 100PF)
Capacitor(50WV 100PF)
Capacitor(50WV 100PF)
Capacitor(50WV 100PF)
Capacitor(25WV 0.1µF)
Capacitor(50WV 15PF)
Capacitor(50WV 0.1µF)
Resistor(1/16W 0Ω ±5%)
– 10 –
[BAT1]
[C1]
[C2]
[C3]
[C4]
[C5]
[C6]
[C7]
[C8]
[C11]
[C12]
[C13]
[C14]
[C15]
[C100]
[C101]
[C102]
[C104]
[C105]
[C107]
[C109]
[C110]
[C111]
[C112]
[C113]
[C114]
[C115]
[C116]
[C117]
[C118]
[C125]
[C126]
[C127]
[C128]
[C129]
[C130]
[C131]
[C132]
[C133]
[C134]
[C135]
[C136]
[C137]
[C138]
[C139]
[C140]
[C141]
[C142]
[C143]
[C144]
[C146]
[C147]
[C148]
[C149]
[C150]
[C151]
[C152]
[C154]
[C157]
[C158]
[C159]
[C160]
[C161]
[C163]
[C164]
[C168]
[C169]
[C170]
[C171]
[C174]
[C175]
[C176]
[C177]
[C178]
[C179]
[C180]
[C182]
[C183]
[C185]
[C186]
UX-510UA
FO-1470U
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
DESCRIPTION
[8] Control PWB unit
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
VCKYCY1CB104K
VCKYCY1CB104K
VCKYCY1AF105Z
VRS-CY1JB000J
VCKYCY1AF105Z
VRS-CY1JB000J
VCKYCY1EF104Z
VCKYCY1CB104K
VRS-CY1JB000J
VRS-CY1JB000J
VCKYCY1AF105Z
VCCCCY1HH221J
VCKYCY1AF105Z
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1AF105Z
VCKYCY1HB102K
VCTYPA1HF104Z
QCNCM7014SC0G
QCNCM2442SC0B
QCNCM7014SC0B
QCNCM2499SC1D
QCNCM7014SC0F
QCNCM7014SC1E
QCNCM2499SC0F
QCNCM2401SC0B
QCNCM7014SC1F
VHE1N4748A/-1
VHD1SS355//-1
VHD1SS355//-1
VHDHRW0202B-1
VHD1SS355//-1
VHD1SS355//-1
VHD1SS355//-1
VHD1SS355//-1
QFS-P2010SCZZ
VHITD62001AP1
RH-IX2202SCZZ
RH-IX2203SCZZ
QSOCZ2051SC32
VHI27020FPS0B
RH-IX2168SCZZ
VHIW24258S7LE
VHISCE114//-1
RH-IX2201SCZZ
VHINJM318M/-F
VHISCE114//-1
VHINJM2113M-1
VRS-CY1JB000J
VRS-CY1JB000J
VRS-CY1JB000J
VRS-TS2AD000J
VRS-CY1JB000J
VRS-CY1JB000J
VHPSG206S//-1
VHPSG206S//-1
VSDTC143ZK/-1
VSDTC143ZK/-1
VSRNC1402//-1
VSRNC1402//-1
VRS-RE3AA102J
VRS-CY1JB271J
VRS-CY1JB474J
VRS-CY1JB103J
VRS-CY1JB000J
VRS-CY1JB562J
VRS-CY1JB271J
VRS-CY1JB271J
VRS-CY1JB106J
VRS-CY1JB223J
VRS-CY1JB000J
VRS-CY1JB000J
VRS-CY1JB000J
VRS-CY1JB513J
VRS-CY1JB000J
VRS-CY1JB000J
VRS-CY1JB103J
VRS-CY1JB000J
VRS-CY1JB271J
VRS-CY1JB224J
AB
AB
AC
AA
AC
AA
AA
AB
AA
AA
AC
AA
AC
AA
AA
AC
AA
AC
AB
AB
AD
AG
AB
AC
AF
AA
AD
AC
AB
AB
AD
AB
AB
AB
AB
AD
AE
AM
AH
AC
BN
BB
AQ
BG
AG
AF
BG
AG
AA
AA
AA
AA
AA
AA
AG
AG
AD
AD
AC
AC
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
N
N
N
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
B
B
B
C
B
B
B
B
B
B
B
B
C
C
C
C
C
C
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
Capacitor(16WV 0.1µF)
Capacitor(16WV 0.1µF)
Capacitor(10WV 1µF)
Resistor(1/16W 0Ω ±5%)
Capacitor(10WV 1µF)
Resistor(1/16W 0Ω ±5%)
Capacitor(25WV 0.1µF)
Capacitor(16WV 0.1µF)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 0Ω ±5%)
Capacitor(10WV 1µF)
Capacitor(50WV 220PF)
Capacitor(10WV 1µF)
Capacitor(25WV 0.1µF)
Capacitor(25WV 0.1µF)
Capacitor(10WV 1µF)
Capacitor(50WV 1000PF)
Capacitor(50WV 0.1µF)
Connector(7pin)
Connector(2pin)
Connector(2pin)
Connector(14pin)
Connector(6pin)
Connector(15pin)
Connector(6pin)
Connector(2pin)
Connector(16pin)
Diode(1N4748A)
Diode(1SS355)
Diode(1SS355)
Diode(HRW0202B)
Diode(1SS355)
Diode(1SS355)
Diode(1SS355)
Diode(1SS355)
IC protector(KAB2402)
IC(TD62001AP)
IC(HCT244)
IC(LV125A)
IC socket(32pin)
IC,EPROM(2MB)
IC(MSM51V4800E)
IC(W24258S-70LE)
IC(SCE114)
IC(HCT04)
IC(NJM318M)
IC(20415)
IC(NJM2113)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/10W 0Ω ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 0Ω ±5%)
Photo transistor(SG206S)
Photo transistor(SG206S)
Transistor(DTC143ZK)
Transistor(DTC143ZK)
Transistor(RNC1402)
Transistor(RNC1402)
Resistor(1W 1.0KΩ ±5%)
Resistor(1/16W 270Ω ±5%)
Resistor(1/16W 470KΩ ±5%)
Resistor(1/16W 10KΩ ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 5.6KΩ ±5%)
Resistor(1/16W 270Ω ±5%)
Resistor(1/16W 270Ω ±5%)
Resistor(1/16W 10MΩ ±5%)
Resistor(1/16W 22KΩ ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 51KΩ ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 10KΩ ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 270Ω ±5%)
Resistor(1/16W 220KΩ ±5%)
– 11 –
[C188]
[C189]
[C190]
[C191]
[C192]
[C196]
[C197]
[C198]
[C207]
[C214]
[C216]
[C218]
[C219]
[C220]
[C221]
[C223]
[C224]
[C227]
[CNCCD]
[CNCSW]
[CNLED]
[CNLIUA]
[CNMT]
[CNPN]
[CNPW]
[CNSP]
[CNTH]
[D1]
[D100]
[D101]
[D102]
[D103]
[D104]
[D105]
[D106]
[FU100]
[IC1]
[IC2]
[IC3]
[IC4]
[IC4]
[IC5]
[IC8]
[IC9](Within IC9 and IC13 pair)
[IC10]
[IC11]
[IC13](Within IC9 and IC13 pair)
[IC15]
[L101]
[L107]
[L112]
[L116]
[L118]
[L119]
[PI1]
[PI2]
[Q100]
[Q102]
[Q104]
[Q105]
[R1]
[R101]
[R102]
[R104]
[R106]
[R107]
[R108]
[R109]
[R113]
[R115]
[R116]
[R117]
[R119]
[R120]
[R123]
[R124]
[R125]
[R127]
[R128]
[R129]
UX-510UA
FO-1470U
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
DESCRIPTION
[8] Control PWB unit
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
VRS-CY1JB271J
VRS-CY1JB103J
VRS-CY1JB000J
VRS-CY1JB271J
VRS-CY1JB271J
VRS-CY1JB271J
VRS-CY1JB271J
VRS-CY1JB000J
VRS-CY1JB223J
VRS-CY1JB103J
VRS-CY1JB271J
VRS-CY1JB271J
VRS-CY1JB271J
VRS-CY1JB102J
VRS-CY1JB471J
VRS-CY1JB203J
VRS-CY1JB271J
VRS-CY1JB271J
VRS-CY1JB471J
VRS-CY1JB471J
VRS-CY1JB101J
VRS-CY1JB000J
VRS-CY1JB104J
VRS-CY1JB000J
VRS-CY1JB102J
VRS-CY1JB203J
VRS-CY1JB221J
VRS-CY1JB105J
VRS-CY1JB271J
VRS-CY1JB271J
VRS-CY1JB102J
VRS-CY1JB333J
VRS-CY1JB472J
VRS-CY1JB393J
VRS-CY1JB000J
VRS-CY1JB000J
VRS-CY1JB472J
VRS-CY1JB113J
VRS-CY1JB104J
VCCCCY1HH221J
VRS-CY1JB000J
VRS-CY1JB000J
VRS-CY1JB104J
VRS-CY1JB302J
VRS-CY1JB433J
VRS-CY1JB000J
VRS-CY1JB102J
VRS-CY1JB222J
VRS-CY1JB000J
VRS-CY1JB271J
VRS-CY1JB271J
VRS-TS2AD000J
VRS-CY1JB271J
VRS-CY1JB000J
VRS-CY1JB000J
VCCCCY1HH221J
VRS-CY1JB000J
VRS-CY1JB224J
VRS-CY1JB000J
VRS-CY1JB103J
VRS-CY1JB103J
VRS-CY1JB103J
RR-TZ3018SCZZ
RR-TZ3017SCZZ
RR-TZ3017SCZZ
RR-TZ3017SCZZ
RR-TZ3018SCZZ
RR-TZ3018SCZZ
RR-TZ3017SCZZ
RR-TZ3017SCZZ
RR-TZ3017SCZZ
RR-TZ3017SCZZ
RR-TZ3029SCZZ
RR-TZ3017SCZZ
RR-TZ3017SCZZ
RR-TZ3018SCZZ
VHI62FP332P-1
RRLYD3130SCZZ
RCRSB0297AFZZ
RCRSQ2157SCZZ
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AB
AC
AC
AC
AF
AN
AD
AF
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
Resistor(1/16W 270Ω ±5%)
Resistor(1/16W 10KΩ ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 270Ω ±5%)
Resistor(1/16W 270Ω ±5%)
Resistor(1/16W 270Ω ±5%)
Resistor(1/16W 270Ω ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 22KΩ ±5%)
Resistor(1/16W 10KΩ ±5%)
Resistor(1/16W 270Ω ±5%)
Resistor(1/16W 270Ω ±5%)
Resistor(1/16W 270Ω ±5%)
Resistor(1/16W 1KΩ ±5%)
Resistor(1/16W 470Ω ±5%)
Resistor(1/16W 20KΩ ±5%)
Resistor(1/16W 270Ω ±5%)
Resistor(1/16W 270Ω ±5%)
Resistor(1/16W 470Ω ±5%)
Resistor(1/16W 470Ω ±5%)
Resistor(1/16W 100Ω ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 100KΩ ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 1KΩ ±5%)
Resistor(1/16W 20KΩ ±5%)
Resistor(1/16W 220Ω ±5%)
Resistor(1/16W 1MΩ ±5%)
Resistor(1/16W 270Ω ±5%)
Resistor(1/16W 270Ω ±5%)
Resistor(1/16W 1KΩ ±5%)
Resistor(1/16W 33KΩ ±5%)
Resistor(1/16W 4.7KΩ ±5%)
Resistor(1/16W 39KΩ ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 4.7KΩ ±5%)
Resistor(1/16W 11KΩ ±5%)
Resistor(1/16W 100KΩ ±5%)
Capacitor(50WV 220PF)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 100KΩ ±5%)
Resistor(1/16W 3KΩ ±5%)
Resistor(1/16W 43KΩ ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 1KΩ ±5%)
Resistor(1/16W 2.2KΩ ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 270Ω ±5%)
Resistor(1/16W 270Ω ±5%)
Resistor(1/10W 0Ω ±5%)
Resistor(1/16W 270Ω ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 0Ω ±5%)
Capacitor(50WV 220PF)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 220KΩ ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 10KΩ ±5%)
Resistor(1/16W 10KΩ ±5%)
Resistor(1/16W 10KΩ ±5%)
Resistor array(470Ωx4)
Resistor array(270Ωx4)
Resistor array(270Ωx4)
Resistor array(270Ωx4)
Resistor array(470Ωx4)
Resistor array(470Ωx4)
Resistor array(270Ωx4)
Resistor array(270Ωx4)
Resistor array(270Ωx4)
Resistor array(270Ωx4)
Resistor array(1KΩx4)
Resistor array(270Ωx4)
Resistor array(270Ωx4)
Resistor array(470Ωx4)
IC(XC62FP3302P)
Relay(OJE-SH-124DM)
Crystal(32.768kHz)
Crystal(32.256MHz)
– 12 –
[R130]
[R131]
[R132]
[R133]
[R134]
[R135]
[R136]
[R137]
[R139]
[R140]
[R141]
[R142]
[R143]
[R144]
[R146]
[R151]
[R152]
[R153]
[R154]
[R155]
[R160]
[R163]
[R164]
[R165]
[R166]
[R168]
[R170]
[R171]
[R172]
[R173]
[R175]
[R176]
[R178]
[R179]
[R180]
[R181]
[R182]
[R183]
[R184]
[R185]
[R188]
[R189]
[R190]
[R195]
[R196]
[R198]
[R200]
[R201]
[R202]
[R203]
[R204]
[R205]
[R206]
[R207]
[R208]
[R209]
[R210]
[R212]
[R213]
[R220]
[R221]
[R222]
[RA1]
[RA2]
[RA3]
[RA4]
[RA5]
[RA6]
[RA7]
[RA8]
[RA9]
[RA10]
[RA11]
[RA12]
[RA13]
[RA14]
[REG1]
[RY1]
[X1]
[X2]
UX-510UA
FO-1470U
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
AA
N
C
Jumper wire
BU
N
E
Control PWB unit(Within ROM)
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
C
C
C
B
B
B
B
B
C
C
C
C
C
C
C
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
Varistor(RA-391P-V6-2)
Cable
Capacitor(50WV 22µF)
Capacitor(50WV 22µF)
Capacitor(50WV 4.7µF)
Capacitor(50WV 22µF)
Capacitor(50WV 22µF)
Capacitor(250WV 0.82µF)
Capacitor(50WV 22µF)
Capacitor(50WV 10µF)
Capacitor(50WV 22µF)
Capacitor(25WV 0.1µF)
Capacitor(50WV 0.1µF)
Capacitor(10WV 1µF)
Capacitor(25WV 0.039µF)
Capacitor(50WV 33PF)
Capacitor(50WV 0.1µF)
Capacitor(50WV 820PF)
Capacitor(10WV 1µF)
Capacitor(50WV 33PF)
Capacitor(50WV 220PF)
Capacitor(50WV 2200PF)
Capacitor(50WV 0.1µF)
Capacitor(50WV 1000PF)
Capacitor(16WV 0.1µF)
Capacitor(50WV 0.01µF)
Capacitor(50WV 220PF)
Capacitor(50WV 1000PF)
Capacitor(50WV 2200PF)
Relay(OUAZ-SH-124DZ)
Jack
Connector(14pin)
Jack
Diode(1SS133)
Diode(1SS133)
Diode(DA204K)
IC(NJM2904M)
IC(NJM2904M)
Coil(R-5C)
Coil(R-5C)
Coil(R-5C)
Coil(R-5C)
Coil(R-5C)
Coil(R-5C)
Coil(R-5C)
Photo coupler(TLP521)
(DTC143ZK)
(DTC143ZK)
Transistor(2SC2412KR)
Resistor(1/2W 22KΩ ±5%)
Resistor(1/10W 1KΩ ±5%)
Resistor(1/10W 100Ω ±5%)
Resistor(1/16W 3.3KΩ ±5%)
Resistor(1/10W 22KΩ ±5%)
Resistor(1/16W 20KΩ ±5%)
Resistor(1/16W 15KΩ ±5%)
Resistor(1/10W 300Ω ±5%)
Resistor(1/16W 47KΩ ±5%)
Resistor(1/16W 620Ω ±5%)
Resistor(1/16W 4.7KΩ ±5%)
Resistor(1/16W 100Ω ±5%)
Resistor(1/16W 20KΩ ±5%)
Resistor(1/16W 1KΩ ±5%)
Resistor(1/10W 86.6KΩ ±1%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 3.3KΩ ±5%)
Resistor(1/16W 220KΩ ±5%)
Resistor(1/16W 150Ω ±5%)
Resistor(1/16W 1KΩ ±5%)
Resistor(1/16W 1.5KΩ ±5%)
Resistor(1/16W 8.2KΩ ±5%)
DESCRIPTION
[8] Control PWB unit
242
901
QCNW-4358XH95
(Unit)
DCEKC281PXHZZ
[9] TEL/LIU PWB unit
!
!
!
!
!
!
!
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
VHVRA391PV6-1
QCNW-4704XHZZ
VCEAGA1HW226M
VCEAGA1HW226M
VCEAGA1HW475M
VCEAGA1HW226M
VCEAGA1HW226M
RC-FZ3024SCZZ
VCEAGA1HW226M
VCEAGA1HW106M
VCEAGA1HW226M
VCKYCY1EF104Z
VCKYTV1HF104Z
VCKYCY1AF105Z
VCKYCY1EB393K
VCCCCY1HH330J
VCKYTV1HF104Z
VCKYCY1HB821K
VCKYCY1AF105Z
VCCCCY1HH330J
VCCCCY1HH221J
VCKYCY1HB222K
VCKYTV1HF104Z
VCKYCY1HB102K
VCKYCY1CB104K
VCKYCY1HB103K
VCCCCY1HH221J
VCKYCY1HB102K
VCKYCY1HB222K
RRLYD3433XHZZ
QJAKZ2079XH0D
QCNCW2500SC1D
QJAKZ2046SCBB
VHDDSS133//-1
VHDDSS133//-1
VHDDA204K//-1
VHINJM2904M-2
VHINJM2904M-2
RFILN2027XHZZ
RFILN2027XHZZ
RFILN2027XHZZ
RFILN2027XHZZ
RFILN2027XHZZ
RFILN2027XHZZ
RFILN2027XHZZ
VHPTLP521-1BL
VSDTC143ZK/-1
VSDTC143ZK/-1
VS2SC2412KR-1
VRD-HT2HY223J
VRS-TS2AD102J
VRS-TS2AD101J
VRS-CY1JB332J
VRS-TS2AD223J
VRS-CY1JB203J
VRS-CY1JB153J
VRS-CY1JB301J
VRS-CY1JB473J
VRS-CY1JB621J
VRS-CY1JB472J
VRS-CY1JB101J
VRS-CY1JB203J
VRS-CY1JB102J
VRSTS2AD8662F
VRS-CY1JB000J
VRS-CY1JB332J
VRS-CY1JB224J
VRS-CY1JB151J
VRS-CY1JB102J
VRS-CY1JB152J
VRS-CY1JB822J
AE
AD
AB
AB
AA
AB
AB
AG
AB
AA
AB
AA
AA
AC
AB
AA
AA
AA
AC
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AH
AD
AG
AH
AA
AA
AC
AG
AG
AC
AC
AC
AC
AC
AC
AC
AE
AD
AD
AD
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
– 13 –
[AR1]
[ARG]
[C1]
[C2]
[C4]
[C5]
[C6]
[C8]
[C9]
[C10]
[C13]
[C101]
[C102]
[C106]
[C108]
[C109]
[C110]
[C112]
[C113]
[C114]
[C115]
[C117]
[C118]
[C119]
[C123]
[C124]
[C125]
[C126]
[C127]
[CML1]
[CNHJ]
[CNLIUA]
[CNLNJ]
[D1]
[D2]
[D101]
[IC101]
[IC102]
[L1]
[L2B]
[L3]
[L4]
[L5]
[L7]
[L9]
[PC4]
[Q102]
[Q104]
[Q105]
[R5]
[R105]
[R106]
[R108]
[R111]
[R112]
[R113]
[R114]
[R115]
[R116]
[R117]
[R118]
[R120]
[R121]
[R122]
[R123]
[R124]
[R125]
[R127]
[R128]
[R130]
[R131]
UX-510UA
FO-1470U
NO.
PARTS CODE
PRICE
RANK
NEW
MARK
PART
RANK
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AG
AG
AG
AC
AC
AA
AA
AB
AB
N
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
B
B
Resistor(1/16W 39KΩ ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 1KΩ ±5%)
Resistor(1/16W 10KΩ ±5%)
Resistor(1/16W 3.3KΩ ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 20KΩ ±5%)
Resistor(1/16W 20KΩ ±5%)
Resistor(1/16W 0Ω ±5%)
Resistor(1/16W 0Ω ±5%)
Door switch
Hook switch
Transformer(I2164)
Varistor(ERZV5D471)
Varistor(ERZV5D471)
Zener diode(HZ2C1)
Zener diode(HZ2C1)
Zener diode(HZ27)
Zener diode(MTZJ5.1B)
BC
N
E
TEL/LIU PWB unit
AD
AL
AD
AF
AD
AB
AH
AF
AD
AD
AD
AD
AD
AD
AD
AF
AD
AH
AD
AL
AE
AE
AD
AH
AH
AD
AM
AK
AQ
AQ
AG
AQ
AD
AD
AD
AC
AC
AC
AC
AC
AC
AC
AC
AC
AE
AC
AC
AC
AC
AC
AC
AD
BE
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
B
B
A
A
B
B
C
C
C
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
Capacitor(R46KI3110M)
Capacitor(KMF200VB-150(M)VV-18)
Capacitor(CC45SL3AD681JYNN)
Capacitor(GRM39B152K50PT)
Capacitor(AMZ-472J50)
Resistor(MCR10EZHJ000)
Capacitor(LXJ35VB330(M)MC-10)
Capacitor(LXJ16VB330(M)FT-8)
Capacitor(GRM39B104K50PT)
Capacitor(DD08-959B152K500)
Capacitor(DD410-959SR104M25)
Capacitor(GRM39B102K50PT)
Capacitor(DE0905-959E472Z1K)
Capacitor(GRM39CH271J50PT)
Capacitor(R46KI3110M)
Capacitor(DE1410-1E332M-KX)
Base post ass’y(THL-P03P B1)
Connector(06R-FJ)
Diode(1SS355TE-17)
Diode(S3L20U-4004P15)
Diode(AK04-V0)
Diode(ERA22-06V3)
Diode stack(S1WB(A)60B-4102)
Current fuse(23702.5 ME600)
Circuit protect(CCP2E100)
Beads core(BL02RN1-R62T4)
IC(UPC78M05AHF)
Filter(ELF15N005A)
Heat sink(MN001-5001AT)
Heat sink(MN001-5002AT)
Photo coupler(PS2501-1L)
FET(FS5KM-14-AN)
Transistor(2SC4115S QR TP)
Transistor(2SC1741AS TP QR)
Transistor(2SC1740S-TP)
Resistor(RD50SS-T26-225J)
Resistor(RDM14TS474J)
Resistor(RDM14TS474J)
Resistor(MCR18EZHJ561)
Resistor(MCR10EZHJ682)
Resistor(MCR10EZHJ473)
Resistor(MCR10EZHJ181)
Resistor(MCR10EZHJ473)
Resistor(MCR10EZHJ471)
Resistor(RSMF1TBR15G)
Resistor(MCR10EZHJ472)
Resistor(MCR10EZHJ102)
Resistor(MCR10EZHJ334)
Resistor(MCR10EZHF2202)
Resistor(MCR10EZHF8201)
Resistor(MCR18EZHJ332)
Resistor(SPR2-T52-104J)
Transformer(PTTN117-KTT)
DESCRIPTION
[9] TEL/LIU PWB unit
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
901
VRS-CY1JB393J
VRS-CY1JB000J
VRS-CY1JB102J
VRS-CY1JB103J
VRS-CY1JB332J
VRS-CY1JB000J
VRS-CY1JB203J
VRS-CY1JB203J
VRS-CY1JB000J
VRS-CY1JB000J
QSW-Z2226SCZZ
QSW-Z2263XHZZ
RTRNI2164XHZZ
VHVERZV5D471/
VHVERZV5D471/
VHEHZ2C1///-1
VHEHZ2C1///-1
VHEHZ27-1//-1
VHEMTZJ5R1B-1
(Unit)
DCEKL266CXH01
[R132]
[R133]
[R134]
[R135]
[R136]
[R137]
[R138]
[R139]
[R140]
[R141]
[SW1]
[SW2]
[T1]
[VA2]
[VA3]
[ZD4]
[ZD5]
[ZD6]
[ZD7]
[10] Power supply PWB unit
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
0CBUGZ1274ZZ/
0CBUGAL151SM/
0CBUGCU681EL/
0CBUGXGCF152/
0CBUGFF472EH/
0CBUEXCAA000/
0CBUGAE331TS/
0CBUGAC331TR/
0CBUGXGCF104/
0CBUGCS152JG/
0CBUGCD104DT/
0CBUGXGCF102/
0CBUGCU472BW/
0CBUGXGDF271/
0CBUGZ1274ZZ/
0CBUGCM332BJ/
0CBPKZ1219ZZ/
0CBPKZ1251ZZ/
0CBUBY0020AK/
0CBUBC0336AZ/
0CBUBC0304AZ/
0CBUBC0169CL/
0CBUBB0248EZ/
0CBPJCSX2501/
0CBPZZ0906ZZ/
0CBBFZ89256Z/
0CBUCB0111AZ/
0CBUKZ0790ZZ/
0CBLRZ6708ZQ/
0CBLRZ6709ZQ/
0CBUDC0062MZ/
0CBUAG0161EZ/
0CBUAC0255AM/
0CBUAC0264AK/
0CBUAC0034EL/
0CBUEEC225CF/
0CBUEEB474DJ/
0CBUEEB474DJ/
0CBUEXDAA561/
0CBUEXCAA682/
0CBUEXCAA473/
0CBUEXCAA181/
0CBUEXCAA473/
0CBUEXCAA471/
0CBUEFDR15DB/
0CBUEXCAA472/
0CBUEXCAA102/
0CBUEXCAA334/
0CBUEYAA2202/
0CBUEYAA8201/
0CBUEXDAA332/
0CBUEFE104DH/
0CB829655033/
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
– 14 –
[C1]
[C2]
[C3]
[C4]
[C5]
[C6]
[C8]
[C10]
[C12]
[C13]
[C16]
[C17]
[C23]
[C24]
[C25]
[C26]
[CN1]
[CN2]
[D5]
[D7]
[D8]
[D9]
[DS1]
[F1]
[F3]
[FB1]
[IC1]
[L1]
[MT1]
[MT2]
[PC1]
[Q1]
[Q2]
[Q3]
[Q4]
[R1]
[R2]
[R3]
[R4]
[R5]
[R6]
[R7]
[R8]
[R9]
[R10]
[R13]
[R14]
[R15]
[R16]
[R17]
[R18]
[R24]
[T1]
UX-510UA
FO-1470U
PARTS CODE
NO.
PRICE
RANK
NEW
MARK
PART
RANK
AD
AD
AD
AC
AD
N
B
B
B
B
B
Varistor(S07K150GA)
Variable resistor(EVN CYA A03 B13(102))
Zener diode(RD4.3SB2-T1)
Zener diode(RD30FB3-T7)
Zener diode(RD6.2SB-T1)
BF
N
E
Power supply PWB unit
AB
AA
AH
AX
AB
AA
AA
C
C
C
B
B
C
C
Capacitor(50WV 22µF)
Capacitor(50WV 0.022µF)
Cable
IC(TCD1208AP)
Transistor(2SC1815GR)
Resistor(1/4W 2.2KΩ ±5%)
Resistor(1/4W 39Ω ±5%)
BE
E
CCD PWB unit
AC
AH
AE
C
C
C
Tact switch
FRSNS sensor
ORGSNS sensor
E
Operation panel PWB unit(Without sensor)
DESCRIPTION
[10] Power supply PWB unit
54
55
56
57
58
!
901
0CBUEZ0666ZZ/
0CBUFBA102EE/
0CBUBXAD4R3C/
0CBUBDBM300D/
0CBUBXAD6R2C/
(Unit)
RDENT2157XHZZ
[V1]
[VR1]
[ZD2]
[ZD4]
[ZD5]
[11] CCD PWB unit
1
2
3
4
5
6
7
901
VCEAGA1HW226M
VCKYPU1HF223Z
QCNW-4692AXZZ
VHITCD1208AP1
VS2SC1815GR-1
VRD-RC2EY222J
VRD-RC2EY390J
(Unit)
DCEKD475AAX05
[C1]
[C2]
[CN1]
[IC1]
[Q1]
[R1]
[R2]
[12] Operation panel PWB unit
1
2
3
901
QSW-K0005AWZZ
QSW-M2246AXZZ
QSW-M2247AXZA
(Unit)
DCEKP351BXH02
BF
N
– 15 –
[SW]
[FRSNS]
[ORGNSN]
UX-510UA
FO-1470U
Index
PARTS CODE
[C]
CCNW-391AXH01
CGERH2314AX51
CGERH2363AX01
CLEVP2254AX01
CLEVP2255AX01
CLEVP2256AX01
CROLR2362AX01
CROLR2363XH02
[D]
DCEKC281PXHZZ
″
DCEKD475AAX05
″
DCEKL266CXH01
″
DCEKP264CXH01
″
DCEKP264CXH02
″
DCEKP351BXH02
″
DCYOD475AXH03
DUNTK464BXHFW
DUNTK464BXHOG
[G]
GCABA2289XHYA
GCABA2289XHYB
GCABB2290XHAA
GCABB2290XHAB
GCABC2291XHYA
GCABC2291XHYB
GCOVA2375XHYZ
GCOVA2376XHYA
GCOVA2376XHYB
GCOVA2378AXZZ
GLEGG2063AXZZ
[H]
HPNLH2405XHSA
HPNLH2405XHSB
[J]
JBTN-2202AXSC
JBTN-2202XHYA
JBTN-2203AXSC
JBTN-2203XHYA
JBTN-2204AXSB
JBTN-2204XHYA
JBTN-2205AXSB
JBTN-2205XHYA
JBTN-2206XHYA
JBTN-2206XHYB
JKNBP2074XHYA
JKNBP2074XHYB
[L]
LBNDJ2006XHZZ
″
″
LBNDJ2008SCZZ
LBSHP2078XHZZ
LBSHP2086AXZZ
LBSHP2088AXZZ
LFRM-2164XHAA
LFRM-2179XHZA
LFRM-2180XHAZ
LFRM-2181AXZZ
LPLTG2707XHZZ
LPLTM2791AXFW
LPLTM2886AXFW
LPLTM2924XHFW
LPLTM3122XHZZ
LPLTP2790XHZZ
LPLTP2884AXZZ
LPLTP2888XHYA
LPLTP2888XHYB
LPLTP2889XHYA
LPLTP2889XHYB
LPLTP2890XHYA
LPLTP2890XHYB
LPLTP2968XHZZ
LSTPP2044XHZZ
No.
PRICE NEW PART
RANK MARK RANK
1-3
1-59
1-6
5-1
5-2
5-3
1-45
1-46
AK
AP
AK
AE
AE
AE
AN
AK
N
1-4
8-901
4-1
11-901
1-5
9-901
1-1
2-901
1-1
2-901
2-1
12-901
4-901
7-9
7-9
BU
BU
BE
BE
BC
BC
BH
BH
AT
AT
BF
BF
BN
AX
AP
N
N
2-2
2-2
1-15
1-15
1-75
1-75
1-76
1-22
1-22
1-77
1-79
AR
AE
AZ
AL
AH
AL
AK
AP
AG
AE
AC
N
N
N
N
N
N
N
N
N
1-99
1-99
AG
AC
N
N
2-3
2-3
2-4
2-4
2-5
2-5
2-6
2-6
2-7
2-7
6-1
6-1
AG
AH
AF
AF
AD
AE
AD
AD
AE
AC
AD
AC
1-13
5-17
6-2
1-84
7-12
1-53
1-7
4-2
6-3
1-28
5-4
3-1
1-29
5-5
1-66
1-97
3-2
1-30
1-67
1-67
7-2
7-2
7-3
7-3
1-93
1-31
AA
AA
AA
AA
AC
AC
AC
AF
AK
AX
AV
AE
AD
AQ
AQ
AD
AD
AP
AG
AC
AM
AE
AM
AE
AP
AF
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
C
C
C
C
C
C
C
C
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
D
D
D
D
D
D
C
C
C
C
C
D
D
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
PARTS CODE
LX-BZ2138XHZZ
LX-BZ2182SCZZ
LX-BZ2222AXZZ
LX-WZ2228AXZZ
LX-WZ2228XHZZ
LX-WZ2246XHZZ
[M]
MARMP2026XHZZ
MCAMP2023AXZZ
MLEVP2248AXZZ
MLEVP2249XHYZ
MLEVP2252XHYZ
MLEVP2253XHYA
MLEVP2257XHZA
MLEVP2258XHYZ
MSPRC2920AXFJ
MSPRC2924AXFJ
MSPRC2926AXFJ
MSPRC2927AXFJ
MSPRC2928AXFJ
MSPRC2964AXFJ
MSPRC2999XHFJ
MSPRC3039XHFJ
MSPRC3210XHZZ
MSPRC3212XHZZ
MSPRC3247XHZZ
MSPRC3249XHZZ
MSPRD2929AXFJ
MSPRD2962AXFJ
MSPRD3197XHZZ
MSPRD3250XHZZ
MSPRP2817SCZZ
MSPRP3123XHZZ
MSPRT2923AXFJ
MSPRT2932AXFJ
MSPRT3235XHZZ
[N]
NBRGP2141AXZZ
NGERH2275XHZZ
″
NGERH2279XHZZ
″
NGERH2281XHZZ
NGERH2309XHZZ
NGERH2310XHZZ
NGERH2315XHZZ
NGERH2317XHZZ
NGERH2356XHZZ
NGERH2358AXZZ
NGERH2359AXZZ
NGERH2360AXZZ
NGERH2361AXZZ
″
NGERH2362AXZZ
NGERH2365AXZZ
NGERH2366AXZZ
NGERH2367AXZZ
NGERP2318XHZZ
NROLP2332XHZZ
NROLP2334XHZA
″
NROLP2396XHZZ
NROLR2333XHZZ
NROLR2466XHZZ
NROLR2467XHZZ
NROLR2468XHZZ
NSFTM2268XHYZ
NSFTM2278AXZZ
NSFTM2279AXZZ
NSFTM2280AXZZ
NSFTZ2257AXZZ
NSFTZ2281XHZZ
[P]
PCOVA2114XHYZ
PCOVA2115XHSA
PCOVA2115XHSB
PCUSG2111XHZZ
PCUSG2112XHZZ
PCUSS2114XHZZ
PCUSS2124XHZZ
No.
PRICE NEW PART
RANK MARK RANK
1-B7
4-B8
1-B3
6-W1
1-W1
1-W2
AB
AB
AC
AB
AB
AB
3-17
5-6
6-4
1-32
1-33
1-8
3-3
1-34
6-6
3-4
1-68
1-37
6-7
6-5
1-35
1-17
6-15
6-16
1-36
1-23
1-38
5-7
3-5
1-60
4-3
1-98
3-6
1-69
3-7
AC
AD
AD
AD
AD
AD
AC
AD
AC
AC
AD
AC
AC
AD
AC
AC
AE
AD
AB
AB
AC
AC
AD
AB
AC
AC
AC
AC
AB
3-8
1-9
3-9
1-61
5-8
5-9
1-54
1-39
7-13
3-10
3-11
1-55
1-50
5-15
1-57
5-10
5-11
1-70
1-71
1-62
1-24
1-63
1-18
3-12
1-94
1-10
3-13
1-11
1-58
1-51
6-8
1-64
1-40
3-14
1-19
AC
AC
AC
AC
AC
AD
AC
AE
AE
AC
AC
AC
AD
AE
AE
AE
AE
AD
AD
AD
AD
AD
AC
AC
AD
AP
AK
AM
AS
AE
AH
AK
AK
AE
AD
1-78
7-4
7-4
5-16
1-90
1-95
4-15
AE
AL
AE
AE
AE
AD
AA
– 16 –
C
C
C
C
C
C
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
PARTS CODE
PFLT-2006XHZZ
PFLT-2009AXZZ
PGIDM2478AXZR
PGIDM2479XHYA
PGIDM2480XHYA
PGIDM2481XHYA
PGIDM2481XHYB
PGIDM2482XHAZ
PGIDM2483XHYA
PGIDM2483XHYB
PGIDM2484XHYA
PGIDM2484XHYB
PGIDM2485XHYA
PGIDM2519XHZL
PGLSP2058XHZZ
PHOP-2095XHYA
PHOP-2095XHYB
PLNS-2049XHZZ
PMIR-2070XHZZ
PMIR-2071XHZZ
PMIR-2072XHZZ
PRBNN2009SCZZ
PSEL-2015SCZZ
PSHEP3606XHZZ
PSHEZ3196AXZZ
PSHEZ3258AXZZ
PSHEZ3290AXZZ
PSHEZ3291AXZZ
PSHEZ3292AXZZ
PSHEZ3293AXZZ
PSHEZ3332AXZZ
PSHEZ3341AXZZ
PSHEZ3342AXZZ
PSHEZ3344AXZZ
PSHEZ3366XHZZ
PSHEZ3563XHZZ
[Q]
QACCD2054XHZZ
QCNCM2401SC0B
QCNCM2442SC0B
QCNCM2499SC0F
QCNCM2499SC1D
QCNCM7014SC0B
QCNCM7014SC0F
QCNCM7014SC0G
QCNCM7014SC1E
QCNCM7014SC1F
QCNCW2500SC1D
QCNW-289ASCOG
QCNW-289ASCOW
QCNW-290ASCZZ
QCNW-390AXHZZ
″
QCNW-392AXHZZ
QCNW-393AXHZZ
QCNW-394AXHZZ
QCNW-395AXHZZ
QCNW-4358XH95
QCNW-4692AXZZ
QCNW-4704XHZZ
QFS-P2010SCZZ
QJAKZ2046SCBB
QJAKZ2079XH0D
QSOCZ2051SC32
QSW-F2224SCZZ
QSW-K0005AWZZ
QSW-M2246AXZZ
″
QSW-M2247AXZA
″
QSW-Z2226SCZZ
QSW-Z2263XHZZ
[R]
RC-FZ3024SCZZ
RCORF2125XHZZ
RCRSB0297AFZZ
RCRSQ2157SCZZ
RDENT2157XHZZ
″
RFILN2027XHZZ
No.
PRICE NEW PART
RANK MARK RANK
4-4
1-41
6-10
1-52
1-72
1-12
1-12
3-15
1-25
1-25
1-26
1-26
1-65
6-9
4-5
1-73
1-73
4-6
4-7
4-8
4-9
7-14
1-74
4-17
4-10
4-12
3-16
2-8
6-11
1-43
1-81
1-86
1-87
1-42
6-17
1-80
AA
AD
AD
AK
AF
AP
AG
AM
AE
AC
AE
AC
AC
AN
AE
AM
AE
AZ
AG
AH
AH
AV
AB
AA
AC
AD
AD
AD
AE
AH
AE
AC
AC
AD
AD
AB
1-20
8-106
8-100
8-105
8-102
8-101
8-103
8-99
8-104
8-107
9-32
7-10
7-10
7-15
1-2
2-11
6-12
6-13
5-12
4-13
8-242
11-3
9-2
8-116
9-33
9-31
8-120
5-13
12-1
2-9
12-2
2-10
12-3
9-82
9-83
AP
AA
AB
AF
AG
AD
AB
AB
AC
AD
AG
AG
AG
AE
AK
AK
AM
AE
AD
AD
AA
AH
AD
AD
AH
AD
AC
AE
AC
AH
AH
AE
AE
AG
AG
9-8
1-14
8-240
8-241
1-21
10-901
9-39
AG
AE
AD
AF
BF
BF
AC
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
S
C
C
C
C
C
C
C
C
C
C
C
C
C
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
C
C
C
C
C
C
C
C
C
C
C
C
B
B
B
E
E
C
UX-510UA
FO-1470U
PRICE NEW PART
RANK MARK RANK
PARTS CODE
No.
RFILN2027XHZZ
″
″
″
″
″
RH-IX2168SCZZ
RH-IX2201SCZZ
RH-IX2202SCZZ
RH-IX2203SCZZ
RHEDZ2063XHZZ
RMOTZ2161XHZZ
RR-TZ3017SCZZ
″
″
″
″
″
″
″
″
RR-TZ3018SCZZ
″
″
″
RR-TZ3029SCZZ
RRLYD3130SCZZ
RRLYD3433XHZZ
RTRNI2164XHZZ
[S]
SPAKA213AAXZZ
SPAKA261CXHZZ
SPAKA262CXHZZ
SPAKA328CXHZZ
SPAKC263CXHZZ
SPAKC300CXHTZ
SPAKP4381AXZZ
[T]
TCADZ3055XHZZ
TINSE4157XHTZ
TINSE4162XHTZ
TLABH276CXHZZ
TLABH4161AXZZ
[U]
UBATL2049SCZZ
[V]
VCCCCY1HH101J
″
″
″
″
″
″
″
″
″
VCCCCY1HH150J
″
″
VCCCCY1HH180J
VCCCCY1HH221J
″
″
″
″
VCCCCY1HH330J
″
″
VCEAGA0JW227M
″
VCEAGA1EW476M
″
VCEAGA1HW106M
″
″
″
″
VCEAGA1HW107M
″
″
9-40
9-41
9-42
9-43
9-44
9-45
8-122
8-125
8-118
8-119
6-14
5-14
8-225
8-226
8-227
8-230
8-231
8-232
8-233
8-235
8-236
8-224
8-228
8-229
8-237
8-234
8-239
9-30
9-84
AC
AC
AC
AC
AC
AC
BB
AG
AM
AH
BQ
AX
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AB
AN
AH
AG
7-11
7-17
7-18
7-5
7-19
7-19
7-16
AC
AC
AC
AC
AG
AK
AG
7-1
7-6
7-6
7-7
1-27
AN
AK
AL
AD
AD
8-1
AF
B
8-19
8-20
8-50
8-57
8-64
8-65
8-73
8-74
8-75
8-76
8-70
8-71
8-78
8-27
8-92
8-201
8-217
9-21
9-27
8-28
9-16
9-20
8-6
8-7
8-2
8-10
8-4
8-11
8-13
8-14
9-10
8-5
8-8
8-12
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AD
AD
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
N
N
N
N
N
N
N
N
N
N
N
N
N
N
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
D
D
D
D
D
D
D
D
D
D
D
D
PARTS CODE
VCEAGA1HW226M
″
″
″
″
″
″
″
″
VCEAGA1HW475M
VCKYCY1AF105Z
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
VCKYCY1CB104K
″
″
″
VCKYCY1EB393K
VCKYCY1EF104Z
″
″
″
″
″
″
″
″
″
″
VCKYCY1HB102K
″
″
″
″
″
″
″
″
″
″
″
″
″
″
VCKYCY1HB103K
″
VCKYCY1HB222K
″
VCKYCY1HB472K
VCKYCY1HB821K
VCKYPU1HF223Z
VCKYTV1CF225Z
″
″
″
″
″
″
″
″
″
No.
8-3
8-9
9-3
9-4
9-6
9-7
9-9
9-11
11-1
9-5
8-16
8-17
8-23
8-29
8-30
8-33
8-34
8-36
8-42
8-43
8-44
8-45
8-46
8-48
8-69
8-83
8-85
8-91
8-93
8-96
9-14
9-19
8-81
8-82
8-88
9-25
9-15
8-15
8-32
8-35
8-41
8-58
8-72
8-77
8-87
8-94
8-95
9-12
8-21
8-22
8-24
8-25
8-37
8-38
8-39
8-49
8-53
8-54
8-55
8-56
8-97
9-24
9-28
8-67
9-26
9-22
9-29
8-68
9-18
11-2
8-26
8-40
8-47
8-51
8-52
8-59
8-60
8-61
8-62
8-63
– 17 –
PRICE NEW PART
RANK MARK RANK
AB
AB
AB
AB
AB
AB
AB
AB
AB
AA
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AB
AB
AB
AB
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AD
AD
AD
AD
AD
AD
AD
AD
AD
AD
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
PARTS CODE
No.
VCKYTV1HF104Z
″
″
″
″
″
VCTYPA1HF104Z
VHDDA204K//-1
VHDDSS133//-1
″
VHDHRW0202B-1
VHD1SS355//-1
″
″
″
″
″
VHEHZ2C1///-1
″
VHEHZ27-1//-1
VHEMTZJ5R1B-1
VHE1N4748A/-1
VHINJM2113M-1
VHINJM2904M-2
″
VHINJM318M/-F
VHISCE114//-1
″
VHITCD1208AP1
VHITD62001AP1
VHIW24258S7LE
VHI27020FPS0B
VHI62FP332P-1
VHPSG206S//-1
″
VHPSNK15A24-1
VHPTLP521-1BL
VHVERZV5D471/
″
VHVRA391PV6-1
VRD-HT2HY223J
VRD-RC2EY222J
VRD-RC2EY390J
VRS-CY1JB000J
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
8-18
8-31
8-79
9-13
9-17
9-23
8-98
9-36
9-34
9-35
8-111
8-109
8-110
8-112
8-113
8-114
8-115
9-87
9-88
9-89
9-90
8-108
8-128
9-37
9-38
8-126
8-124
8-127
11-4
8-117
8-123
8-121
8-238
8-135
8-136
4-14
9-46
9-85
9-86
9-1
9-50
11-6
11-7
8-66
8-80
8-84
8-86
8-89
8-90
8-129
8-130
8-131
8-133
8-134
8-145
8-151
8-152
8-153
8-155
8-156
8-158
8-163
8-168
8-182
8-184
8-196
8-197
8-202
8-203
8-207
8-210
8-215
8-216
8-218
8-220
9-65
9-73
9-77
9-80
9-81
PRICE NEW PART
RANK MARK RANK
AA
AA
AA
AA
AA
AA
AC
AC
AA
AA
AD
AB
AB
AB
AB
AB
AB
AA
AA
AB
AB
AC
AG
AG
AG
AF
BG
BG
AX
AE
AQ
BN
AF
AG
AG
AZ
AE
AC
AC
AE
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
N
N
C
C
C
C
C
C
C
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
UX-510UA
FO-1470U
PARTS CODE
No.
VRS-CY1JB101J
″
VRS-CY1JB102J
″
″
″
″
″
″
VRS-CY1JB103J
″
″
″
″
″
″
″
VRS-CY1JB104J
″
″
VRS-CY1JB105J
VRS-CY1JB106J
VRS-CY1JB113J
VRS-CY1JB151J
VRS-CY1JB152J
VRS-CY1JB153J
VRS-CY1JB203J
″
″
″
″
″
VRS-CY1JB221J
VRS-CY1JB222J
VRS-CY1JB223J
″
VRS-CY1JB224J
″
″
VRS-CY1JB271J
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
″
VRS-CY1JB301J
VRS-CY1JB302J
VRS-CY1JB332J
″
″
VRS-CY1JB333J
VRS-CY1JB393J
″
VRS-CY1JB433J
VRS-CY1JB471J
″
″
VRS-CY1JB472J
″
″
VRS-CY1JB473J
VRS-CY1JB474J
VRS-CY1JB513J
VRS-CY1JB562J
VRS-CY1JB621J
VRS-CY1JB822J
VRS-RE3AA102J
8-181
9-61
8-174
8-185
8-191
8-208
9-63
9-69
9-74
8-144
8-157
8-162
8-170
8-221
8-222
8-223
9-75
8-183
8-200
8-204
8-188
8-149
8-199
9-68
9-70
9-56
8-176
8-186
9-55
9-62
9-78
9-79
8-187
8-209
8-150
8-169
8-160
8-219
9-67
8-142
8-147
8-148
8-159
8-161
8-164
8-165
8-166
8-167
8-171
8-172
8-173
8-177
8-178
8-189
8-190
8-211
8-212
8-214
9-57
8-205
9-53
9-66
9-76
8-192
8-195
9-72
8-206
8-175
8-179
8-180
8-194
8-198
9-60
9-58
8-143
8-154
8-146
9-59
9-71
8-141
PRICE NEW PART
RANK MARK RANK
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
PARTS CODE
VRS-TS2AD000J
″
VRS-TS2AD101J
VRS-TS2AD102J
VRS-TS2AD223J
VRSTS2AD8662F
VSDTC143ZK/-1
″
″
″
VSRNC1402//-1
″
VS2SC1815GR-1
VS2SC2412KR-1
[X]
XBBSD30P06000
XBPSD30P06K00
XBPSN40P06K00
XEBSD20P06000
XEBSD30P10000
″
″
XEBSE30P10000
XEBSF30P12000
[0]
0CBBFZ89256Z/
0CBLRZ6708ZQ/
0CBLRZ6709ZQ/
0CBPJCSX2501/
0CBPKZ1219ZZ/
0CBPKZ1251ZZ/
0CBPZZ0906ZZ/
0CBUAC0034EL/
0CBUAC0255AM/
0CBUAC0264AK/
0CBUAG0161EZ/
0CBUBB0248EZ/
0CBUBC0169CL/
0CBUBC0304AZ/
0CBUBC0336AZ/
0CBUBDBM300D/
0CBUBXAD4R3C/
0CBUBXAD6R2C/
0CBUBY0020AK/
0CBUCB0111AZ/
0CBUDC0062MZ/
0CBUEEB474DJ/
″
0CBUEEC225CF/
0CBUEFDR15DB/
0CBUEFE104DH/
0CBUEXCAA000/
0CBUEXCAA102/
0CBUEXCAA181/
0CBUEXCAA334/
0CBUEXCAA471/
0CBUEXCAA472/
0CBUEXCAA473/
″
0CBUEXCAA682/
0CBUEXDAA332/
0CBUEXDAA561/
0CBUEYAA2202/
0CBUEYAA8201/
0CBUEZ0666ZZ/
0CBUFBA102EE/
0CBUGAC331TR/
0CBUGAE331TS/
0CBUGAL151SM/
0CBUGCD104DT/
0CBUGCM332BJ/
0CBUGCS152JG/
0CBUGCU472BW/
0CBUGCU681EL/
0CBUGFF472EH/
0CBUGXGCF102/
0CBUGXGCF104/
0CBUGXGCF152/
0CBUGXGDF271/
0CBUGZ1274ZZ/
No.
PRICE NEW PART
RANK MARK RANK
8-132
8-213
9-52
9-51
9-54
9-64
8-137
8-138
9-47
9-48
8-139
8-140
11-5
9-49
AA
AA
AA
AA
AA
AA
AD
AD
AD
AD
AC
AC
AB
AD
C
C
C
C
C
C
B
B
B
B
B
B
B
B
6-B6
1-B4
1-B5
2-B1
1-B2
5-B2
6-B2
1-B10
1-B11
AA
AA
AA
AA
AA
AA
AA
AA
AA
C
C
C
C
C
C
C
C
C
10-26
10-29
10-30
10-24
10-17
10-18
10-25
10-35
10-33
10-34
10-32
10-23
10-22
10-21
10-20
10-57
10-56
10-58
10-19
10-27
10-31
10-37
10-38
10-36
10-45
10-52
10-6
10-47
10-42
10-48
10-44
10-46
10-41
10-43
10-40
10-51
10-39
10-49
10-50
10-54
10-55
10-8
10-7
10-2
10-11
10-16
10-10
10-13
10-3
10-5
10-12
10-9
10-4
10-14
10-1
AD
AQ
AQ
AH
AD
AH
AH
AD
AD
AD
AQ
AD
AE
AE
AL
AC
AD
AD
AD
AM
AG
AC
AC
AC
AE
AD
AB
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AC
AD
AD
AF
AH
AL
AD
AF
AD
AD
AD
AD
AD
AD
AF
AD
AD
– 18 –
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
B
C
C
A
C
C
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
B
B
C
C
C
C
C
C
C
C
C
C
C
C
C
C
PARTS CODE
No.
0CBUGZ1274ZZ/
0CBUKZ0790ZZ/
0CB829655033/
10-15
10-28
10-53
PRICE NEW PART
RANK MARK RANK
AD
AK
BE
N
N
C
C
B
UX-510UA
FO-1470U
COPYRIGHT © 2000 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
SHARP CORPORATION
Communication Systems Group
Quality & Reliability Control Center
Higashihiroshima, Hiroshima 739-0192, Japan
Printed in Japan
A0010-1823DS•IS•T