Sharp PC-9800T Instruction manual

R

S

Ladder logic programmning software

Version 3.1

Produced in Sep. 2001

Model name

JW-100SP

Instruction Manual

Thank you for purchasing the ladder logic programming software JW-100SP.

Please read the instruction manual carefully in order to apply the software correctly by understanding its functions and operations.

Please keep this instruction manual near you. It will certainly help you when you encounter problems.

Note

Note

・Despite of our effort to create products with excellency, should you find any deficiency, please notify the dealer where you obtained the software or our customer service companies.

・Users are not authorized to copy the whole or the part of this instruction manual and software without our consent.

・Due to the amelioration of the product, please understand that the materials of this instruction manual and software are subject to change without notification.

・We are not held responsible for any damages created as the result of using this software , nor damages claimed by the third party as the result of using this software.

Ladder logic programming software JW-100SP

■ Instruction Manual

Chapter 1 Introduction

Chapter 2 Setup

Chapter 3 Basic operation

Chapter 4 Let’s create program

Chapter 5 Menu operation

Chapter 6 Program edit

Chapter 7 Setup each data

Chapter 8 Monitor

Chapter 9 Print

Table of Contents


･････････････････････････････････････････････････ 1･1∼9

1-1 Features 1•1

1-2 Compatible PC models 1•2

1-3 System requirements 1•2

1-4 Connection between the personal computer and the PC 1•3

■ Basic system organization 1•3

■ System organization using communication 1•4

1-5 Product organization 1•8

■ Ladder logic programming software (JW-100SP) 1•8

■ Communication adapter (JW-100SA) 1•8

1-6 Caution 1•8

■ On-line caution up on using the monitor 1•8

1-7 Conventions used in this manual 1•9

■ Display of menu, command, dialog box 1•9

■ Display of mouse operation 1•9

■ Display of key operation 1•9

Chapter 2 Setup

･･･････････････････････････････････････････････････････ 2･1∼4

Chapter 3 Basic operation

･････････････････････････････････････････････ 3･1 ∼27

3-1 Starting-up and quitting 3•1

■ Starting-up JW-100SP 3•1

■ Quitting JW-100SP 3•2

3-2 List of files about JW-100SP 3•3

3-3 Screen configuration 3•4

■ Screen when you create new file 3•4

■ Main toolbar 3•5

■ Sub toolbar 3•6

■ Message bar 3•7

■ Toolbar for editing ladder 3•8

■ Toolbar for editing mnemonic 3•9

■ Toolbar for editing data 3•10

3-4 Kinds of windows 3•11

■ Main window 3•11

■ Basic window 3•12

■ Other windows 3•15

3-5 Selection of commands 3•19

■ Click button of the oolbar 3•19

■ Select the command from the menu 3•19

■ Select a command from the shortcut menu 3•20

■ Using the shortcut keys 3•21

3-6 Function summary 3•22

■ File 3•22

■ Edit 3•23

■ Instruction 3•24

Table of Contents-1

■ Monitor 3•24

■ Display 3•25

■ Setup 3•25

■ PC 3•26

■ Tools 3•26

■ Window 3•27

■ Help 3•27

Chapter 4 Let's create program ･････････････････････････････････････････ 4･1∼21

4-1 Start-up JW-100SP 4•2

4-2 Create ladder program 4•4

■ Setup input type 4•4

■ Inputting A contact, B contact and coil 4•5

■ Inputting timer and counter 4•9

■ Inputting application instruction 4•10

■ Program check and conversion to mnemonic 4•13

4-3 PC transfer/monitor 4•16

4-4 Print 4•19

■ The print example 4•21

Chapter 5 Menu operation

･･････････････････････････････････････････････ 5･1∼83

5-1 File 5•3

■ New 5•4

■ Open

■ Close

5•6

5•7

■ Save 5•8

■ Save as 5•8

■ FD Verify 5•9

■ Page Setup

■ Printer Setup

■ Quit 5•9

5•9

■ Print Program 5•9

■ Print Preview 5•9

5•9

■ Export Files (Data/Symbol) 5•10

■ Import Files (Data/Symbol) 5•11

5-2 Edit

■ Undo

5•12

5•13

■ Cut

■ Copy

5•13

5•13

■ Paste

■ Image Copy

5•13

5•13

■ Find 5•14

■ Find Previous 5•17

■ Find Next

■ Find Coil

■ Insert Cell

■ Insert Row

■ Delete Cell

■ Delete Row

5•17

5•17

5•18

5•18

5•18

5•18

Table of Contents-2

■ Create Line Comment 5•19

■ Zoom

■ Jump

5•20

5•21

■ Library 5•23

■ Program Check 5•24

■ Converts data in batch 5•25

■ Replacing Contacts 5•26

■ Assigns symbol 5•27

5-3 Instruction 5•29

5-4 Monitor

5-5 Display

5•30

5•31

■ Main toolbar /Sub toolbar /Status bar /Tree bar /Toolbar for editing ladder /Toolbar for editing

mnemonic /Toolbar for editing data /Message bar 5•33

■ Select address display type 5•34

■ View change 5•34

5•35 ■ Select monitoring display type

■ Change segment file 5•36

■ Word wrap 5•37

■ Data list 5•38

■ Arrange ladder diagram 5•42

■ Displays in Symbol/Displays in comment/Displays in Symbol&Comment 5•43

■ Displays in binary notation/Displays in octal notation/Displays in decimal notation/Displays in decimal

notation(+/-)/Displays in hex notation /Displays in ASCII 5•43

■ Displays in byte/Displays in word/Displeys in double word

■ Displays in detail/Displays as a list 5•45

5•44

5-6 Setup 5•46

■ Select PC model 5•46

■ Select memory capacity

■ Setup communication 5•48

5•47

■ Memory clear 5•54


■ Setup display 5•56

■ Key assignment 5•57

■ Check input of same symbol 5•58

5-7 PC5•59

■ PC transfer

■ Run /Stop 5•62

5•59

■ PC operation

[1] I/O search

5•62

5•63

[2] Secret 5•64

[3] CU memory clear 5•65

[4] Parity check 5•66

[5] EEPROM 5•67

[6] I/O table automatic registration 5•68

■ PC monitor 5•69

[1] Error monitor 5•69

[2] Scan time monitor 5•70

[3] Clock monitor 5•71

Table of Contents-3

■ Modem Connection 5•72

5-8 Tool 5•73

■ Library 5•73

■ Multipoints monitor 5•73

■ Sampling Trace 5•73

■ Option parameter

■ CAD interface 5•74

5•73

5-9 Window 5•76

■ Open New Window 5•77

■ Overlap Display 5•78

■ Cascade Display 5•79

■ Arrange Icons 5•80

■ Window Name 1, 2, •••

5-10 Window 5•82

■ Find Topic 5•82

■ Version Data 5•83

5•81

Chapter 6 Program edit

･････････････････････････････････････････････････ 6･1∼47

6-1 Ladder programming 6•1

■ [Program:Ladder] window 6•1

■ Select address display type 6•2

■ Program Input method 6•4

[1] Direct input mode 6•4

[2] Dialog input mode 6•9


■ Edit circuit 6•18

[1] Over write/insert mode 6•18

[2] Modify circuit 6•18

[3] Delete circuit 6•22

[4] Insert circuit 6•22

[5] Copy circuit 6•23

[6] Move circuit 6•24

■ Copy circuit between windows

■ Library 6•26

[1] Register to library 6•26

6•23

[2] Read from library

■ Arrange ladder diagram

6•31

6•35

■ Converting ladder to mnemonic

■ Optimization of ladder 6•40

[1] Circuit by the optimization 6•40

[2] Optimization timing 6•41

6-2 Mnemonic programming

■ [Program:mnemonic] window

6•42

6•38

6•42

■ Input by mnemonic 6•42

■ Edit mnemonic 6•43

■ Converting mnemonic to ladder

6-3 Notes when editing a program

6•44

6•46

■ Notes for editing programs in several windows 6•46

Table of Contents-4

Chapter 7 Setup each data

･･････････････････････････････････････････････ 7･1∼13

7-1 Setup system memory 7•1

■ Summary display /operation of system memory 7•1

■ Setup /display of property sheet

■ Manual I/O registration 7•3

7•2

7-2 Setup data memory 7•5

■ Summary display /operation of data memory 7•5

7-3 Setup symbol/comment 7•6

■ Summary display /operation of symbol/comment 7•6

■ Applying text file 7•7

7-4 Setup parameter 7•8

■ Summary display /operation of parameter 7•8

■ Setup model (special I/O module/option module) 7•9

■ Setup/display of property sheet

7-5 Setup other parameters 7•11

7•10

■ Summary display /operation of other parameters 7•11

■ Setup/display of property sheet 7•13


･･････････････････････････････････････････････････････ 8･1∼31

8-1 Start monitoring, stop monitoring 8•1

[1] Monitor at the [Program:Ladder] window 8•1

[2] Monitor at the [Program:Mnemonic] window 8•3

[3] Monitor at the [System ] window 8•4

[4] Monitor at the [Data] window

[5] Monitor at the [Parameter] window

8•5

8•6

8•7 [6] Monitor several windows at the same time

8-2 Multipoints monitor 8•8

[1] Function

[2] Menu operation

8•8

8•11

8-3 Sampling trace 8•15

[1] Sampling trace order 8•16

[2] Menu of the [Sampling Trace] window 8•19

8-4 I/O forced processing 8•24

8-5 Edit program while monitoring 8•25

[1] Change address or values specified

[2] Edit circuit 8•26

8•25

Chapter 9 Print ････････････････････････････････････････････････････････ 9･1∼27

9-1 Page setup 9•3

[1] Setup page of program:ladder

[2] Setup page of program:mnemonic

9•3

[3] Setup page of system

[4] Setup page of data 9•7

9•6

[5] Setup page of symbol 9•8

[6] Setup page of parameter 9•9

[7] Setup page of other parameter 9•10

[8] Setup page of data list 9•11

9-2 HF editor 9•12

9•5

Table of Contents-5

9-3 Print setup

9-4 Print preview

9-5 Print 9•22

9•18

9•20

Table of Contents-6

Chapter 1 Introduction


JW-100SP is a ladder logic programming software that is capable of creating a program by ladder and mnemonic of Sharp New Satellite JW Series PC (programmable controller), as well as setting up data memory, system memory, symbol & comment, and the parameter.

Once created program or various data can be saved as file, or saved as document after having it printed.

By communicating with the JW Series PC, this software is capable of transferring the program or various data as well as executing the monitor and debug functions.

This software works on Windows 95/98/Me or any other personal computer whose operating system is

Windows NT.

1-1 Features

(1) Variety of multi-window systems

・This software features independent windows for each item, like program, system memory or data

memory, so that you can change instantly to the desired window for editing.

・Several windows for one program can be opened at the same time so that you can easily create

the program by referring to other sections of the program.

・Since the list of contact-use(Data List), multipoints monitor and library are independent windows

and that they are most likely observed along the program, you will be able to refer and confirm

as many items as possible.

(2) Variety of program editing functions

・By using the full screen editor, the ladder editing is capable of creating and modifying the

program at all times.

・There are variety of useful editing functions such as symbol input (like the relay number), cut/

copy/paste functions (by using the mouse), enlarging and contracting the ladder drawing,

adding line comment, jump and undo.

・Several methods of ladder inputs are available by using the mouse so that you can adjust the

input method at your preference. You can also execute functions by keyboard.

・Being aware of a particular application instruction's number is not necessary since the available

list will help you select the input of application instruction.

・Sophisticated library functions allow you to create the similar circuit easily.

(3) Monitoring several windows at the same time

・You can monitor a number of windows at the same time. By registering the desired part in the

multipoints monitor window, you can use the monitor function more efficiently.

(4) Variety of parameter setups by property sheet form

・You can easily setup system memory and parameter by selecting the item from the list without

worrying about system memory, parameter address and data content. For this reason, the

instruction manual of the product becomes compact, in concrete and simple fashion, to lessen

or avoid any setup errors.

(5) Variety of printing functions

・The software features an editor exclusively for creating header and footer so that you can freely

create the desired screen.

・There are useful functions such as cross reference, with symbol, with comment, etc.

(6) JW-50SP Upward Interchangeability

・Programs and data that were created under ladder software JW-50SP (IBM-PC versions) can

be used in this software. Also programs and data created by this software can be saved as file

that can be read by JW-50SP software.

1 ・1


1-2 Compatible PC Model

The following JW series PC models are compatible to this software:

JW10

JW20,JW20H

JW30H

JW50/70/100

JW50H/70H/100H

J-board

VME built-in controller

W100

P C

W70H/100H

W16/51

Control Module (CPU)

JW-1324K 、JW-1424K、JW-1624K

JW-1342K 、JW-1442K、JW-1642K

JW-21CU 、JW-22CU

JW-31CUH 、JW-32CUH、JW-33CUH

JW-31CUH1 、JW-32CUH1、JW-32CUM1

JW-33CUH1 、JW-33CUH2、JW-33CUH3

JW-50CU 、JW-70CU、JW-100CU

JW-50CUH 、JW-70CUH、JW-100CUH

Z-311J 、Z-312J、Z-313J、Z-511J、Z-512J

JW-32CV1 、JW-32CV2

ZW-1K0CU 、ZW-1K1CU

ZW-1K2CU 、ZW-1K3CU

ZW-70CU 、ZW-1HCU

ZW-160CU

ZW-501CU 、ZW-501CU2、ZW-501CU3

・You can connect your programmable controller to other optional modules than above.

・For the connection between the personal computer and the programmable controller, refer to

the next page.

・For the settings of each model, refer to page 5-5 and 5-46.

1-3 System Requirements

This software can be used by any personal computers that satisfy the following operating environments:

Item System Requirements

Personal computer

CPU

Operating system

Memory

Hard disk

Monitor

CD-ROM drive

RS-232C port

Mouse

Printer

IBM PC personal computer or NEC PC-9800 series

More than 90MHz of Pentium (More than 200MHz of Pentium recommended)

Microsoft Windows 95/98/Me

Microsoft Windows NT4.0

More than 32M bytes (more than 64M bytes recommended )

30M bytes of the empty area

More than SVGA (800 ×600 dots of the resolution, more than16 color)

One model

More than 1 port

Microsoft mouse or interchangeable pointing devise

(operations only by the keyboard are possible)

Printer that can be used under Windows 95/98/Me/NT environment,when printing the ladder drawing, for example

1 ・2


1-4 Connection between the Personal Computer and the PC

W16

W51, W100

W70H/100H control module

ZW-160CU

ZW-501CU3

ZW-1K0CU

ZW-1K1CU

ZW-1K2CU

ZW-1K3CU

ZW-70CU

ZW-1HCU

JW50/70/100

JW50H/70H/100H control module Network module

ZW-20CM

COMM

SD

RD

CD

LT

TEST

ＳＯ

Ｓ１

Ｓ２

Ｓ３

Ｓ４

Ｓ５

JW-50CU

JW-70CU

JW-100CU

JW-50CUH

JW-70CUH

JW-100CUH

MODE

STA.NO

×10

×1

LT

(ON

→

）

LG

(ON

→

）

LINK FUNCTION

STATION NO.

ZW-20CM

ZW-30CM

JW-20CM

ME-NET module

ME-NET

COMM

SD

RD

CD LT

TEST

COM.E

UNT.E

Ｓ４

Ｓ５

Ｓ６

Ｓ７

ＳＯ

Ｓ１

Ｓ２

Ｓ３

JW-20MN

MODE

STA.NO

×10

×1

L1

(ON

LT

）

→

(ON

LG

）

→

(ON

L1

）

→

(ON

L2

→

L2

ZW-20CM2

JW-20MN

Remote I/O slave station module

ZW-20RS

COMM

SD

RD

CD

LT

TEST

FAULT

ＳＯ

Ｓ１

Ｓ２

Ｓ３

Ｓ４

Ｓ５

Ｓ７

I/O bus extension adapter

Serial interface module

JW-108U

Ethernet module

JW-50CM

COMM

DC

SD

12V

10B5

TEST

ERROR

S0

S1

S3

S4

S5

S6

S7

FL-net module

JW-50FL

LNK

TX

DC12V

TEST

PER

HER

S0

S1

S3

S4

S5

S6

S7

R

O

M

M

R

7 6 5 4 3 2

R

O

R

R

MODE

STA.NO

×10

×1

LT

(ON

→

）

LG

(ON ）

STATION NO.

ZW-20RS

JW-20RS

JW-2EA JW-10SU

(+)

12VIN

JW-50CM

JW-51CM

10B5

10B-T

(＋)

12VIN

(−)

FG

RESET

JW-50FL

JW10 basic module

JW-1324K / 1342K

JW-1424K / 1442K

JW-1624K / 1642K

JW20/JW20H

Control module

JW30H

Control module Network module

ME-NET module

JW-21CU

JW-22CU

JW-31CHU/H1

JW-32CUH/H1/M1

JW-33CUH/H1/H2/H3

JW-22CM JW-21MN

I/O bus extension adapter Ethernet module FL-net module

JW-255CM

CMSDRD12V T ER FT

S7S6S5S4S3S2S1S0

JW-20FL5

LN TX RX 12V T PE HE

S7 S6 S5 S4 S3 S2 S1 S0

JW-32EA

ON

S

H

E

OFF

FG

RESET

JW-255CM

ON

S

H

E

OFF

FG

RESET

JW-20FL5

JW-51FLT

Connection cable

JW-12KC（2m）

Connection cable

ZW-3KC （3m）

（9 pin connector）

Connection with

the IBM PC personal

computer

Communication adapter

JW-100SA

（25 pin connector）

Connection with

the NEC PC-9800 series

※ １ ※ ２

Ladder logic programming software

JW-100SP

Connection cable

JW-22KC （2m）

JW-24KC （4m）

J-board

・CPU board

Z-311J,Z-312J,Z-313J

Z-511J,Z-512J

・Satellite net board

Z-335J

・ME-NET board

Z-334J

VME built-in controller

JW-32CV1

JW-32CV2

Personal computer

※ １ You can only connect one IBM PC personal computer or one NEC PC-9800 series to the connector of your

personal computer (You cannot connect both ９pin connector of JW-100SA and 25 pin connector at the same time)

※ ２ Since the personal computer has the RS-232C port (half-pitched 14 pin), you need a conversion cable to

match the D-sub 25 pin (female) when connecting with the NEC PC9800 series.

1 ・3


■ System Organization Using Communication

(1) Network connection (Standard ：

JW50H/70H/100H

JW-20CM

JW50H/70H/100H

JW-20CM

JW20H/30H

JW-22CM

#00 #01 #77

Satellite net (data link function) maximum 64 stations, maximum 1km

Connection cable

(ZW-3KC)

When connected with

JW-22CM ：JW-22KC/24KC

Personal computer


(JW-100SA)


(JW-100SP)

・Remote programming/monitor

・Parameter setup


Personal computer

Line server

Optical fiber cable

NSU NSU ：Network service module maximum 126 stations

JW50H/70H/100H

ZW-30CM

SUMINET-3200

JW50H/70H/100H

ZW-30CM

Connection cable

(ZW-3KC)

Personal computer


(JW-100SA)


(JW-100SP)

・Remote programming/monitor

・Parameter setup

1 ・4



JW50H/70H/100H

JW-20MN

JW50H/70H/100H

JW-20MN

JW20H/30H

JW-21MN

#00 #01 #77

ME-NET maximum 64 stations, maximum 1km


(JW-100SA)

Personal computer


(JW-100SP)

Connection cable

(ZW-3KC)

When connected with

JW-22CM: JW-22KC/24KC

・Remote programming /monitor

・Parameter setup

(4) Network connection (Expansion)

JW50H/70H/100H

JW-20CM

JW50H/70H/100H

JW-20CM JW-20CM

JW20H/30H

JW-22CM

#00 #01 #00

JW50H/70H/100H

JW-20CM

#77

JW20H/30H

JW-22CM

#01

#77


(JW-100SA)

Personal computer


(JW-100SP)

Connection cable

(ZW-3KC)

・Remote programming/monitor (2 layers)

・Parameter setup

1 ・5


(5) Remote I/O connection

JW50H/70H/100H

JW-20CM JW-20RS JW-20RS JW-20RS

#00 #01 #02 #77


(JW-100SP)

Remote I /O maximum 63 stations, maximum 1km

Personal computer


(JW-100SA)

Connection cable

(ZW-3KC)


・Parameter setup

(6) Computer link connection (RS-485 connection)

Personal computer


(JW-100SP)

JW50H/70H/100H

JW-10CM

JW50H/70H/100H

JW-10CM

JW20H/30H

JW-21CM

RS-232C/422 converter

Z-101HE

RS-232C

(less than 15m)

#01 #02

RS-485 (cable maximum length ：less than1km)

#37

(7) Computer link connection (RS-232C connection)

Personal computer


(JW-100SP)

JW70H/100H

Communication port

RS-232C (less than 15m)

1 ・6


(8) Ethernet connection

JW50H/70H/100H

JW-50CM

Transceiver cable

(maximum 50m)

JW20H/30H

JW-255CM

J W -2 5 5 C M

T ER FT

S7 S6 S5 S4 S3 S2 S1 S0

ON

S

H

E

D

OFF

FG

Host computer

Maximum 100 stations

Terminator Transceiver

10BASE5 coaxial cable

(yellow)

Coaxial cable segment (maximum 500m)

Personal computer


(JW-100SA) Ladder logic programming software

(JW-100SP)

Connection cable

(ZW-3KC)

Use JW-22KC/24KC when connecting to JW-255CM


・Parameter setup

(9) L-net connection

Personal computer

10BASE5 coaxial cable

(maximum 500m)

Terminator

FL-net

Transceiver cable

( maximum 50m )

JW50H/70H

/100H

Transceiver

NC

Hub

10BASE-T twisted pair cable

(maximum 100m)

JW-50FL

Maximum 100 nodes per segment

J-board JW20H/30H


(JW-100SA)

JW-20FLT

Z-336J

Personal computer


(JW-100SP)

Connection cable

(ZW-3KC)

Use JW-22KC/24KC when connecting to JW-20FL5/T

・ Parameter setup

1 ・7


1-5 Product Organization

■ Ladder Logic Programming Software (JW-100SP)

CD-ROM ･･････････････････････････････････････ 1 (quantity)

Instruction manual ･･････････････････････････････ 1 (quantity)

Registration card ･･･････････････････････････････ 1 (quantity)

JW100SP

ラダー設計支援ソフト

For Windows 95 / NT

Copyright 1998 SHARP MANUFACTURING SYSTEMS CORPORATION.

All rights reser ve d.

Windows は、米国マイクロソフト社の米国およびその他の国における登録商標です。

CD-ROM

ラダー設計支援ソフト

®

取扱説明書

初版

1998年2月作成

形名

JW-100SP

Registration card

Instruction manual

(Japanese)

■ Communication Adapter (JW-100SA)

Communication adapter ･･･････････････ 1 (quantity)

80 mm

140 mm

1-6 Caution

When the personal computer and the PC are connected, use the on-line monitor after transferring the PC program to the personal computer, or after transferring the personal computer program to the PC. If you don't transfer the programs, you won't be able to have the correct calculation at the ladder monitor/ mnemonic monitor since the program of PC and personal computer may not be the same.

1 ・8


1-7 Conventions Used in This Manual

■ Display of Menu, Command, Dialog Box

Display Meaning

[ ]

・Displayhe menu name, command name and button name in [ ].

Example) [File] menu, [New] command, [OK] button

・Display the the name of the title bar of the dialog box displayed in [ ].

Example) [Open File] dialog box

[ ] - [ ]

・Show the layers of menu,command.

Example) select [File]-[New].

(It means that [New] command is selected from the [file] menu)

Example) select [PC]-[PC Transfer]-[Write].

(It means that [PC Transfer] menu is selected from the [PC] menu, and in addition, it means to select the [Write] command)

■ Display of Mouse Operations

Display Meaning

Click ・Press the mouse button once and release the button right after.

・Among the two buttons of the mouse, when only“click”is displayed, it is to

press the left button, and when“right click”is displayed, it means to press the

Double click ・Means to press the left button of the mouse quickly twice.

Drag ・Means to keep pressing the left button, then release the button after moving it to

the desired position.

■ Display of Key Operations

Display Meaning

[ ] ・Keys are displayed in [ ].

Example) [Enter] key, [S] key

[ ] + [ ] ・ [+] means to press a number of keys at the same time.

Example) [Ctrl]＋[S] key

Directional key ・The general name of [→] [←] [↑] [↓] keys

1 ・9

Chapter 2 Setup personal computer. In this chapter, the setup order of the ladder logic programming software ・JW-100SP is explained.

JW-100SP operates under Windows 95/98/Me/NT, but the setup order of this software is explained for

Windows 98 environment.

1 ． Start-up Windows 98, and place the JW-100SP

CD-ROM into the CD-ROM drive of the personal

computer.

Place the CD-ROM,

with the label side up.

2 ． Open [My Computer] on the desktop by double clicking

the icon.

3 ． Open the CD-ROM drive by double clicking the icon.

4 ． Double click [setup.exe].

The setup program will start-up, and the next dialog box will be displayed.

When the setup preparation is completed, the next dialog box will be displayed.

2 ・1

Chapter 2 Setup

5 ．Input your [Name] and [Company], and click [Next] button.

The next dialog box will be displayed.

6 ．Click the [Next] button if destination directory is correct.

If you want to change the install destination, click

the [Browse] button to display the [Choose Folder]

dialog box, and assign the drive or folder.

Click [OK] button, and click [Next] button.

When [Next] button is clicked, [Select Program Folder] dialog box will be displayed.

2 ・2

Chapter 2 Setup

7 ．If the program folder is correct, click [Next] button.

If you want to change the folder, input the new folder name, or select the folder from the Existing Folder

list.Then, click [Next] button to start up the setup.

When the setup is completed, the following dialog box will be displayed.

8 ．If you click [Finish] button, the same screen at the moment of the setup is displayed, and it completes the

setup.

(Caution) Sometimes,the following dialog box is displayed instead of the dialog box which is shown

abobe.

In this case,click [Finish] button,and restart the computer.Then,the setup will be complete.

9 ．To start JW-100SP, click [Programs]-[Sms]-[JW100SP] on the start menu of Windows98. (Refer to

Chapter 3)

2 ・3

Chapter 3 Basic Operation (Starting-up and Quitting)

Chapter 3 Basic Operation

3-1 Starting-up and Quitting

How to start or quit JW-100SP will be explained.

■ Starting-up JW-100SP

1 ．Click [Start] button of the task bar on the Windows 98 screen.

2 ．Click [Programs]-[Sms]-[JW100SP] on the start menu.

Click here

Click here

JW-100SP will start-up, and the principle screen (the main window) will be displayed.

3 ・1

Chapter 3 Basic Operation (Starting-up and Quitting)

■ Quitting JW-100SP

1 ．Click [File]-[Quit] on the menu bar.

Click here

You can also quit the operation by clicking [X] at the upper-right of the window.

Click here

3 ・2

Chapter 3 Basic Operation (List of files about JW-100SP)

3-2

List of files about JW-100SP

JW-100SP opens program-related files and a variety of data at a time so that you can create or edit files about JW-100SP. The list of JW-100SP related files is as follows:

C l a s s i f i c a t i o n

P

S r r e

D

P

S e

O r e r y l a a y l l o p s a t r m a a t i g a a t t t t e e b e o r a m d m m e o d n d m e l a e l t

/ m r m e c p r e e o o a l m r m r r a e y a l t o e r a r m e m t d y e e e l n t t a d e t e r s d

M u l t i p o i n t s r e l a t e d m o n i t o r

S a m p il n g t r a c e r e l a t e d

* .

p g m

* .

l a d

* .

l a 2

* .

i s t

* .

i s 2

* .

l c m

* .

s y s

* .

d a t

* .

d f i

* .

f li

* .

p r m

* .

s y c

* .

s y e

* .

s y m

* .

t x t

* .

2 r m

* .

2 r s

* .

2 d m

* .

2 d s

* .

m e m

* .

m e s

* .

3 c m

* .

2 r d

* .

m o n

* .

s m p

E x t e n s i o n C o n t e n t s

P r o g r a m

L a d d e r s c r e e n i n f o r m a t i o n

L a

( i n d d e r c a s e s c r e e n o f i n m o r e f t o r m a t i o n h a n 3 1 .

5 K w o r d s )

M n e m o n i c s c r e e n i n f o r m a t i o n

M n e m o n i c

( i n c a s e o f s c r e e n m o r e i n f t h a n o r m a t i o n

3 1 .

5 K w o r d s )

L i n e c o m m e n t

S y s t e m m e m o r y

D a t a m e m o r y

D a t a m e m o r y , f li e m e m o r y

F li e m e m o r y

P a r a m e t e r ( J W 2 0 H / 3 0 H )

S y m b o l / c o m m e n t



T e x t

R e m o t e I / O m a s t e r s t a t i o n p a r a m e t e r

R e m o t e I / O s l a v e s t a t i o n p a r a m e t e r

D a t a il n k m a s t e r s t a t i o n p a r a m e t e r

D a t a il n k s l a v e s t a t i o n p a r a m e t e r

M E N E T m a s t e r s t a t i o n p a r a m e t e r

M E N E T s l a v e s t a t i o n p a r a m e t e r

S U M I N E T p a r a m e t e r

O t h e r p a r a m e t e r

M u l t i p o i n t s

( r e g i s t e r e d m o n i t o r a d d r e s s )

S a m p il n g t r a c e

D a t a c o m p a t i b i il t y

J W 5 0 S P w i t h

Y e s

N o

N o

N o

N o

N o

Y e s

Y e s

N o

Y e s

Y e s

N o

Y e s ( V 5 .

0 o r l a t e r )

Y e s ( V 4 .

0 A o r p r e v i o u s )

N o

Y e s

Y e s

Y e s

Y e s

Y e s

Y e s

Y e s

Y e s

N o

N o

F li e t y p e * 1

●

●

●

▲

▲

▲

■

■

■

▲

▲

▲

▲

▲

●

■

■

●

●

▲

▲

●

●

●

●

*1 About file type

●: Files you can save by selecting [File]-[Save]/[Save as] in JW-100SP.

■: Files you can save by selecting [File]-[Export Files] in JW-100SP.

You cannot open these files by selecting [File]-[Open]. Insert them into the file in operation

by selecting [File]-[Import Files].

▲: Files you can save by selecting [File]-[Save]/[Save as] in the window of [Option parameters],

[Multipoints monitor], or [Sampling trace].

Note

JW-100SP can read the file that carries the extension, "Data compatibility with JW-50SP: Yes," created and saved by JW-50SP. To read JW-100SP files by JW-50SP, you need to save data in the file by the extension, "Data compatibility with JW-50SP: Yes."

3 ・3

Chapter 3 Basic Operation (Screen Configuration)

3-3 Screen Configuration

①

②

③

Tab

⑤

When you create new file, the [Program: Ladder] windows will be displayed as follows:

⑦

⑥

④

①Menu Bar

②Main Toolbar

③Sub Toolbar

④Status Bar

⑤Tree Bar

：If you click the item name, the menu that calls for JW-100SP

：If you click the button, it calls for that function. → page 3-5

：If you click the button, it calls for that function. → page 3-6

：Data display type or running condition of the PC will be displayed.

：If you click the tab, the window of the selected tab will be active.For

⑥Message Bar

⑦Toolbar for Editing Ladder

the tree display will be different.

：Display the operation-completed massage or the error message.

：Used when the ladder program is created. It is displayed when

[Program :Ladder] window is active.→ page 3-8

⑧Toolbar for Editing Mnemonic ：Used when mnemonic program is created. It is displayed when

[Program :Mnemonic] window is active.→ page 3-9

⑨Toolbar for Editing Data ：Used for the selection of data display types. It is

displayed when [System],[Data],[Parameter] and

[Other Parameter] windows are active.

→ page 3-10

3 ・4

Chapter 3 Basic Operation (Screen Configration)

■ Main Toolbar

PC model name Program memory capacity Project name

Create a new file (program, system memory, data memory, symbol/comment,

or parameter).

Open the existing file (program, system memory, data memory, symbol /comment,

parameter).

Save the set of the files in operation (program, system memory, data memory, symbol/

comment, or parameter) under the current file names.

◎

Cut the selected area and saves it for the moment.

Save the selected area and saves it for the moment.

Paste the data that was cut or copied onto the position of the cursor.

◎

Temporarily keep in the clipboard the selected area you are editing in the ladder program

window as an image data.

It brings back the previous state of the operation.

Change the window of the ladder and mnemonic.

Change between file 8 and file 9 of the program area.

Execute the program check.

Execute the connection of the disconnected circuit, adjustment of the display

position,adjustment of the MCS/JCS condition display, and optimize the ladder circuit.

Print contents of the active window (ladder program, mnemonic program, system memory,

data memory, symbol /comment, parameter).

3 ・5


◎

Display the printing image.

◎

Display the version of JW-100SP.

■ Sub Toolbar

Search history Ladder display magnifying power

Find the mnemonic, address (relay, register etc..), character line (symbol, comment etc..).

Find the mnemonic, address, character line that are selected from the find

character summary from the cursor position to the backward direction.

◎

Find the mnemonic, address, character line that are selected from the find

character summary from the cursor position to the forward direction.

Contract the program (ladder) display.

Enlarge the program (ladder) display.

Display the ladder instruction only by its address in the ladder program window.

Display the ladder instruction only by its symbol in the ladder program window.

Same as [Display]-[Display Type]-[Comment Display Type(8C4R)]

Display the ladder instruction by its address and comment in the ladder program window.

Same as [Display]-[Display Type]-[Comment Display Type(16C2R)]

Display the ladder instruction by its address and comment in the ladder program window.

Display the ladder instruction by its address, symbol and comment in the ladder program

window.

Display each line in the ladder program unfolded in one line in the ladder program window.

3 ・6


Display each program line, which is longer than the window's width, folded in the ladder

program window.

■ Message Bar

Display the operation completed message or the error message.

If you click the right side of the mouse on the message bar, the following menu will be displayed, and you can erase the message if you select the command.

Clear All ：Erase all messages inside the message bar.

3 ・7


■ Toolbar for Editing Ladder

Use when creating ladder program.

Used when inputting A contact.

Used when inputting B contact.

Used when inputting vertical line.

Used when inputting horizontal line.

Used when inputting OUT instruction (coil).

Used when inputting TMR instruction.

Used when inputting CNT instruction.

Used when inputting application instruction.

Used when inputting F-45 instruction (differential OFF).

Used when inputting F-44 instruction (differential ON).

Used when inputting F-43 instruction (revert bit).

Used when you need to extend the frame downward in result of the added OR circuit by,

for example, CNT instruction or multiple inputs of application instruction (F-60 etc..).

Used when erasing the circuit (cell unit).

Convert the ladder circuit to mnemonic.

In case of direct input mode, it changes the instruction cursor to the mouse cursor with

arrow.

3 ・8

■ Toolbar for Editing Mnemonic

Use when creating the mnemonic program.


Used when inputting STR, STR NOT, AND STR, OR STR instruction.

Used when inputting AND, AND NOT, AND STR instruction.

Used when inputting OR, OR NOT, OR STR instruction.

Used when inputting STR NOT, AND NOT, OR NOT instruction.

Used when inputting OUT instruction.

Used when inputting TMR instruction and TMR contact.

Used when inputting CNT instruction and CNT contact.

Used when inputting application instruction.

Change the kinds of instruction and register.

・TMR→DTMR(BCD)→DTMR(BIN)→UTMR(BCD)→UTMR(BIN)

・CNT→DCNT(BCD)→DCNT(BIN)→UCNT(BCD)→UCNT(BIN)

・F-XXX→F-XXXw→F-XXXd→FcXXX→FxXXX→FcXXXw→FxXXXw

・]0000→b0000→09000→19000→ ････ →99000→E0000

Convert mnemonic to ladder circuit.

3 ・9


■ Toolbar for Editing Data

Used when selecting data display types of system memory, data memory, parameter.

Displays data in binary notation

Displays data in octal notation.

Displays data in decimal notation.

Same as [Display]-[Display in Decimal Notation (with +/-)]

Displays data in decimal notation with a sign of plus or minus.

Displays data in hexadecimal notation.

Displays data in ASCII character.

Displays data in 1 byte (8 bit data).

Displays data in 1 word (16 bit data).

Displays data in 2 word (32 bit data).

Displays data in summary list.

◎

Displays data with comment.

3 ・10

3-4 Kinds of Windows

There are following kinds of window in JW-100SP.

Chapter 3 Basic Operation (Kinds of Windows)

[Program:Ladder] window

[Program:Mnemonic] window

[System] window

[Data] window

[Symbol] window

[Parameter] window

[Register Library]/[Read from Library] window

[Assign Symbol] window

[Data List] window

[Multipoints Monitor] window

[Sampling Trace] window

[Option Parameter] window

[Edit Circuit (Change)]/[Edit Circuit (Insert)]/[Edit Circuit (Delete)] window

[HF Edit] window

[Help] window

■ Main Window

Main window is a window which is opened up at the starting-up of JW-100SP.

If you close the main window, JW-100SP will quit the system.

3 ・11


■ Basic Window

Basic window can be selected by clicking on the tree bar, or by the [Window] menu of the menu bar.

Tree Bar [Window] menu

[

[

There are six basic windows below:

[ P r

P

[

[

P

W

S

S a

[ r r y y o

D a i s n g o g r a a m t t m d r w w e m a b o a i m i o e t

] w m n n l e

]

] d

: M d w

: r ] i

N

L o o w n w i i a w n e w a m n n w d d d o i d d n o w o e e m o n d r w w o

] i c w

]

C o n t e n t s

P o s s i b l e f o r s

P e l

C m o e c t i o n d e l s

C r e a t e , p r o g r a m s a v e , m o n i t o r , p r i n t , e t c .

.

.

t h e l a d d e r

C r e a t e , p r o g r a m s a v e , m o n i t o r , p r i n t , e t c .

.

.

o f t h e m n e m o n i c

S e t u p , s a v e , m e m o r y m o n i t o r , p r i n t , e t c .

.

.

o f t h e s y s t e m

A

A

A ll ll ll m m m o o o d e d e d e l l l s s s

S e t u p , s a v e , m o n i t o r , p r i n t , e t c .

.

.

o f t h e d a t a m e m o r y A ll m o d e l s

S e t u p , s a v e , m o s y m b o l / c o m m e n t n i t o r , p r i n t , e t c .

.

.

o f t h e

P a r a m e t e r s e s p e c i a l / o p t i o n t u p m o

, d s a v e , u l e m o n i t o r , p r i n t , e t c .

.

.

o f t h e

A

J ll

W m

2 0 o

, d e

J W l s

3 0 H

Note

If you click [Program] tab of the Tree Bar,[Program:Ladder] window will be active. To make

[Program:Mnemonic] window active, select [Program :Mnemonic] window from the [Window].

Also, you can interchange between [Program :Ladder] and [Program:Mnemonic] windows by selecting [Display]-[Change Display] of the menu bar, or by clicking the button of the Main

Toolbar.

3 ・12

(1) [Program:Ladder] window

(2) [Program:Mnemonic] window

(3) [System] window


(4) [Data] window

3 ・13


(5) [Symbol] window

(6) [Parameter] window

3 ・14


■ Other Windows

The followings are the windows that are displayed when "command" of the menu bar is selected.

[

[

[

[ R e g i

[ R e

A

S

O p s a d a t i s

[ i g

D m o

W n f r o m n s a p t il i a n

P n s t e r g a d

L r i o

L i b r a r y ]

L i b r a r y ]

S y s

T a w m b t ] r a m e n o w c a l ] e ] t e m i n r ] d e w i n d o w w w i n d o w w i n d o w i n w i d n o d

[ E d i t C i r c u i t ( C h a n g e ) ] w i n d o w

[ E d i t C i r c u i t ( I w i n d o w n s e n t ) ]

[ E d i t C i r c u i t ( D e l e t e ) ] w i n d o w w

[ M u l t i p o i n t s M o n i t o r ] w i n d o w o w o w

P o s s i b l e w i n d o w s s e l e c t i o n f o r

P r o g r a m : L a d d e r



S y m b o l

P r o g r a m : l a d d e r

M a i n


P r o g r a m : M n e m o n i c

S y s t e m

D a t a

S y m b o l

P a r a m e t e r

M a i n



S y s t e m

D a t a

S y m b o l

P a r a m e t e r

M a i n



S y s t e m

D a t a

S y m b o l

P a r a m e t e r


C o m m a n d s o f t h

[ D i s p l a y ] [ D a t a L i s t ] e

[ E d i t ] [ A s s i g n S y m b o l ] m

[ T o o l ] [ S a m p il n g T r a c e ] e

[ T o o l ] [ L i b r a r y ] [ R e g i s t e r ]

[ T o o l ] [ L i b r a r y ] [ R e a d ]

[ T o o l ] [ O p t i o n P a r a m e t e r ] n u

[ T o o l ] [ M u l t i p o i n t s M o n i t o r ] b a r

[ M o n i t o r ] [ E d i t C i r c u i t ] [ C h a n g e ] e t c .

.

.

P r o g r a m : L a d d e r [

[

M

M o o n n i i t t o o r ] r ]

[

[

E

E d d i i t t

C i

C i r c r c u i u i t t ]

]

[

[

I n

D s e l e e n t t e

]

]

[ H

[

F

H e

E l d i p ] t ] w i w n i n d d o o w w




S y s t e m

D a t a

S y m b o l

P a r a m e t e r

O p t i o n

D a t a

P

L i s t a r a m e t e r

M a i n



S y s t e m

D a t a

S y m b o l

P a r a m e t e r

[

[

F

B li e ] o

[ H e l t

S h e o e l t

[ P a

H F g e

E d i p ] [ F i n d e s c e t i o n t u p

S e t u p ] t o r ] b u t t o n

T o p i c ] o f o f t h e t h e t a b l e k e y w o o f r d c

.

o n t e n t s , o r

3 ・15


(1) [Register Library] window

(2) [Assign Symbol] window

(3) [Data List] window

3 ・16

(4) [Multipoints Monitor] window


(5) [Sampling Trace] window

(6) [Option Parameter] window

3 ・17


(7) [Edit Circuit (Change)] window

(8) [HF Edit] window

(9) [Help] window

3 ・18

Chapter 3 Basic Operation (Selection of Commands)

3-5 Selection of Commands

A command is an instruction for JW-100SP to take the responsible tasks.

To select a command, one of the following operations is taken in measure.

①Click the button of the toolbar (Main Toolbar, Sub Toolbar)

②Select the command from the menu.

③Select the command from the shortcut menu.

④Use the shortcut key.

■ Click the Button of the Toolbar

(Example :In case of [Find])

Click here

■ Select the Command from the Menu

Commands are grouped and stored in the menu.

Menu

Sub menu

(1) When selecting the command by mouse

If you want to select a command by mouse, click the menu name of the menu bar, and then click the

command name.

The command that has ▼ mark on the right side of the command name contains the sub menu, so

that after moving the mouse pointer to the command name, you can click the command name of the

sub menu.

To close the menu without selecting the command, click simply outside of the menu.

3 ・19


(2) When selecting the command by keyboard

It you want to select a command by keyboard, press [Alt] key to make the menu bar active, and press the key that matches the underlined characters just after the menu name. (for example, in case of [Edit], press [E] key)

Then press the key that matches the underlined characters just after the command name, or the key that matches the numbers (for example, in case of [Find], press [S] key)

By closing the menu without selecting a command, press [Esc] key.

■ Select a Command from the Shortcut Menu

You can display the shortcut menu when the mouse pointer is on the window (Program, System,

Data, Symbol, Parameter, etc...) or the Message Bar. Commands that are objects of the current operations are included in the shortcut menu.

Shortcut menu

To display the shortcut menu, move the mouse pointer on the objects of the operation, and click the right button of the mouse. When the shortcut menu is displayed, click the command name. To close the shortcut menu without selecting the command, click simply outside of the shortcut menu.

3 ・20


■ Use the Shortcut Key

Among commands, there are commands that can be selected by pressing the shortcut key which is displayed at the right side of the command name when the menu is opened. For example, to create a new file, press [N] key with [Ctrl] key being pressed.

There are following shortcut keys.

Shortcut keys Function

[Ctrl] + [N] key

[Ctrl] + [O] key

[Ctrl] + [S] key

[Ctrl] + [P] key

[Ctrl] + [X] key

[Ctrl] + [C] key

[Ctrl] + [V] key

[Ctrl] + [Z] key

[Ctrl] + [F] key

[Ctrl] + [A] key

[Ctrl] + [I] key

[Ctrl] + [L] key

[Ctrl] + [H] key

[Ctrl] + [D] key

[Ctrl] + [G] key

[Ctrl] + [T] key

[Ctrl] + [B] key

[Ctrl] + [J] key

[Ctrl] + [M] key

[Ctrl] + [U] key

[Ctrl] + [K] key

[Shift] + [PageUp] key

[Shift] + [PageDown] key

New

Open

Save

Print

Cut

Copy

Paste

Undo

Find

Find Coil

Insert Cell

Insert Row

Delete Cell

Delete Row

Create Line Comment

Jumps to Top Row

Jumps to Unedited Row

Jumps to Assigned Row

Jumps to Address Mark

Jumps to Program Address

Program Check

Find Previous

Find Next

3 ・21

Chapter 3 Basic Operation (Function Summary)

3-6 Function Summary

Here, the function (command) of the menu bar of the main window and the basic window is explained.

for the detail of each function.

■ File

Command

New

Open

Close

Save

Save As

Import Files

Export Files

FD Verify

Page Setup

Print

Print Preview

Printer Setup

Quit

Function

Create a new basic file (program, system, data, symbol, parameter).

Open the existing basic file (program, system, data, symbol, parameter).

Close the basic file you are editing (program, system, data, symbol, parameter).

Save the basic file you are editing (program, system, data, symbol, parameter) under the current file name.

Save the basic file you are editing (program, system, data, symbol, parameter) under a new file name.

Import the data memory or symbol/comment file created with a ladder software, JW-50SP.

Export the data memory or symbol/comment file you are editing in the file format of a ladder software such as JW-50SP.

Compare the existing files with files in the active window (program, system, data, symbol, parameter).

Setup the format of the page that is to be printed.

Print the contents of the active window (ladder, mnemonic, system, data, symbol, parameter).

Display the image of the files in the active window (ladder, mnemonic, system, data, symbol, parameter).

Setup “select/connection”of the printer.

Quit the system of JW-100SP.

3 ・22


■ Edit

Command

Undo

Cut

Copy

Paste

Image Copy

Find

Find Previous

Find Next

Function

It brings back the previous state of the operation.

Cut the selected area and saves it for the moment.

Save the selected area and saves it for the moment.

Paste the data that was cut or copied onto the position of the cursor.

Temporarily keep in the clipboard the selected area you are editing in the program ladder window as an image data.

Find mnemonic, address (relay, register etc..),character line (symbol, comment etc..) from the active window.

In the selected active window, search mnemonic, address, character line

(that are assigned in the search character summary) from the cursor position to the backward direction.

In the selected active window, search mnemonic, address, character line

Find Coil

(that are assigned in the search character summary) from the cursor position to the forward direction.

Search the output (coil) in which the relay address of the cursor position

(on A contact and B contact) is being used.

Insert the cell in the assigned area.

Insert Cell

Insert Row

Delete Cell

Insert the row in the assigned area.

Delete the cell in the assigned area.

Delete the row in the assigned area.

Delete Row

Create Line Comment

Zoom [Zoom( ＋)]

Zoom [Zoom( −)]

Jump [To Top Row]

Input the comment in the assigned line.

Enlarge the display of the ladder program

Contract the display of the ladder program

Jump [To Unedited Row]

Move the cursor to the front row of the window.

Move the cursor to the unwritten row for the ladder program, and for mnemonic program, the cursor is moved to the row of NOP instruction.

Jump [To Assigned Row] Move the cursor to the assigned row.

Jump [To Address Mark]

Program Check

Move the cursor to the line of address mark which has been setup.

Jump [To Program Address] Move the cursor to the specified address line.

Check the grammar and format of the ladder program.

Converts Data in Batch Convert the address number such as relay or register in batch.

Replacement NO and NC Replace A contact with B contact, or vice versa, at the point equal to the

Assigns Symbol relay address of the specified contact.

[Assign Symbol] window is opened. Here, the symbol that was input by the ladder program is assigned to the address.

3 ・23


■ Instruction

Command

A Contact

B Contact

Horizontal Line

Vertical Line

STR

NOT

AND

OR

OUT

TMR

CNT

FUN

F43

F44

F45

F-20（MD）

Function

Used for inputting A contact when editing ladder.

Used for inputting B contact when editing ladder.

Used for inputting horizontal line when editing ladder.

Used for inputting vertical line when editing ladder.

Used for inputting STR, STR NOT, AND STR, OR STR when editing mnemonic.

Used for inputting STR NOT, AND NOT, OR NOT when editing mnemonic.

Used for inputting AND, AND NOT, AND STR when editing mnemonic.

Used for inputting OR, OR NOT, OR STR when editing mnemonic.

Used for inputting TMR instruction.

Used also for inputting TMR contact when editing mnemonic.

Used for inputting CNT instruction.

Used also for inputting CNT contact when editing mnemonic.

Used for inputting application instruction.

■ Monitor

Command

Start Monitoring

Stop Monitoring

I/O Forced Processing

Edit Circuit [Change]

Edit Circuit [Insert]

Edit Circuit [Delete]

Function

Start the monitoring.

Stop the monitoring.

ON/OFF the relay of the PC with force.

Change the ladder circuit of the PC in the monitoring.

Insert the ladder circuit of the PC in the monitoring.

Delete the ladder circuit of the PC in the monitoring.

3 ・24


■ Display

Command

Display Type

Change Display

Changes Type of Monitor

Change Segment Display

Data List

Arrange Ladder Diagram

Function

Select the display of the address/symbol inside the ladder program.

Change between ladder and mnemonic window.

Assign the monitoring type of the ladder program (notation display yes/no),and the register display type (octal/decimal/hexadecimal)

Change between the file 8 and file 9 of the program area.

[Data List] window is opened. Here, address (contact number, register number etc...), symbol, comment and cross reference that are being used in the program are displayed.

Execute the connection of the disconnected circuit, the display position adjustment of the output instruction, the adjustment of

MCS/JCS condition display, and optimize the ladder circuit.

Displays data in binary notation.



Display data in decimal notation with a sign of plus or minus.

Display in Binary Notation

Display in Octal Notation

Display in Decimal Notation

Display in Decimal Notation

(with +/-)

Displays in Hex Notation

Display in ASCII

Display in Byte

Display in Word

Display in Double Word

Detail Display

Display in List

Main Toolbar

Sub Toolbar

Status Bar

Tree Bar

Toolbar for Edit Data (L)

Toolbar for Edit Data ( I )

Toolbar for Edit Data (E)

Message Bar


Displays data in ASCII character.

Displays data in 1 byte (8 bit data) unit.

Displays data in 1 word (16 bit data) unit.

Displays data in 2 word (32 bit data) unit.

Displays data with comment.

Displays data in a summary list.

■ Setup

Command

Model Setup

Memory Capacity Setup

Communication Setup

Memory Clear

Setup Input Type

Setup Display

Key Layout

Check Input of Same

Symbol

Function

Select the PC models that are objects of the edit/monitor.

Select the capacity of the program memory.

Setup the communication methods with the PC.

Initialize the internal memory of this personal computer using this software.

Setup the input type (input mode, continuous address input, etc...).

Setup the display position of coil, TMR/CNT instruction, application instruction.

Assign keys to input ladder mnemonic.

Select "yes/ no" for checking "input of same symbol" when registering symbol.

3 ・25


■ PC

Command

PC Transfer [Write]

PC Transfer [Read]

PC Transfer [Verify]

Start/Stop

PC Operation [I/O Search]

PC Operation

Register /Change

Password

[Secret] Delete Password

Secret : ON

PC Operation [CU Memory Clear]

PC Operation [Parity Check]

PC Operation [Read from EEPROM]

PC Operation [Write to EEPROM]

Create I/O Table

PC Operation [Read I/O Table]

PC Monitor [Error Monitor]

PC Monitor [Scan Time Monitor]

PC Monitor [Clock Monitor]

Modem Connection

[Connect]

Modem Connection

[Disconnect]

■ Tools

Command

Library [Read]

Library [Register]

Multi Points Monitor

Sampling Trace

Option Parameter

CAD I/F

Function

Write program, a variety of data to the PC.

Read program, a variety of data to the PC.

Verify with the program and the variety of data of the PC.

Run/stop the PC.

Execute I/O search of the PC.

Register/change the password of the PC.

Delete the password of the PC.

Execute ON of the secret function of the PC.

Initialize the memory of the PC.

Execute the parity check of the PC.

Read from the EEPROM/flash ROM of the PC.

Write to the EEPROM/flash ROM of thePC.

Register I/O table of the PC automatically.

Read I/O table of the PC.

Monitor the error condition of the PC.

Monitor the scan time of the PC.

Monitor the internal clock of the PC.

Connect to the communication module of the PC through the modem.

Disconnect the modem communication with the communication module of the PC.

Function

Opens the [Read from Library] window.

・You can read a library.

Opens the [Register Library] window.

・You can register the library.

Opens the [Mltipoints Monitor] window.

・You can monitor any data in data memory or system memory.

Opens the [Sampling Trace] window.

・You can see the ON/OFF information of the programmable controller's

relay or the registry information in the form of time chart.

Opens the [Option Parameter] window.

・You can define the parameter settings of the model to save parameters in

the option module.

Converts the ladder graphical information you are editing to an intermediate language (ASCII code) corresponding to information exchange format.

・You can send the data through the communication port or can read/write

the data into external media.

3 ・26


■ Window

Command

Open New Window

Overlap Display

Cascade Display

Arrange Icons

Window name1, 2, ...

Function

Open the new window that carries the same content as the currently active Window .

Display windows in piles.

Display windows in a row.

Arrange icons under the window.

Activate the assigned window.

■ Help

Command

Find Topic

Version Data

(MMVIEW)

Function

Display the table of contents, or“help”regarding the assigned item by the Keyword.

Displays the version of JW-100SP.

3 ・27

Chapter 4 Let's Create Program

Chapter 4 Let's Create Program

In this chapter, basic operations such as creating a ladder program, transferring a created program to the

PC, monitoring a program or printing a program, are explained.

■ System Configuration

Operations explained in this chapter require the following system configuration.

JW30H (JW-33CUH1)

Connection to

PG/COMM1 port

Connection cable

(JW-22KC)


(JW-100SA)

Personal computer Windows 95


(JW-100SP)

■ Operation Order

The operation orders that are explained in this chapter are described below.

Start-up JW-100SP

Create new files

Setup model

Create ladder program

4-1 Start-up JW-100SP

Check program

4-2 Create ladder program

Save files

Setup communication

Stop PC

Transfer program to PC

Run PC

Start monitoring

Stop monitoring

Print ladder program

4-3 PC transfer/monitoring

4-4 Print

4 ・1


4-1 Start-up JW-100SP

1. Click [Start] button at the task bar on the screen of Windows 95/98.

2. Click [Programs]-[Sms]-[JW100SP] on the start menu.

Click here

JW-100SP will start-up, and the initial screen will be displayed.

3. Click [File]-[New] of the menu bar.

Click here

4 ・2


4. When the [New] dialog box is displayed, input the file name you are creating in the file name box.

(In the example below, "new" is input as the file name.)

If you want to change the position (directory) of the created program, click [Browse] button

and select the directory (Refer to the page 5 -4 for more detail).

5. If you click [OK] button, [Select PC Model] Dialog box will be displayed.

6. After clicking [Series Selection] box, click [JW30H].

7. Click [JW-33CUH1] inside the [Model Selection] box.

8. If you click [OK] button, the input screen of ladder program will be displayed.

4 ・3


4-2 Create Ladder Program

The creating order of the following ladder programs is explained.

00003

00004

00005

00006

00000 00002 T0001

00001

00010 00012 C0002

00011

00020

00021

TMR

0001

0050

CNT

0002

0010

F-63

INC

09100

F-40

END

There are two types of input methods of ladder programs ：direct input and dialog input.

Here, the dialog input is explained mainly.

■ Setup Input Type

1.Click [Setup]-[Setup Input Type] of the menu bar.

Click here

4 ・4


2. When [Setup Input Type] dialog box is displayed, setup the following, and click [OK] button.

■ Inputting A Contact, B Contact and Coil

3. Move the mouse cursor to the cell that is at the left side up of the ladder display (column ：0

row ： 0), and click.

4. When inputting A contact, click [X] of the toolbar for editing ladder.

The following [A contact] dialog box will be displayed.

contact will be displayed, and the cell cursor will move to the right cell.

4 ・5


6. When inputting B contact, click of the toolbar for ediing ladder. The following [B contact] dialog box will be displayed.

displayed and the cell cursor will move to the right cell.

8. To input TMR contact (A contact), first click of the toolbar for ediing ladder. [A contact]

dialog box will be displayed, and press inside the box.

contact (A contact) will be displayed, and the cell cursor will move to the right cell.

10. To input coil (OUT instruction), click

[OUT] dialog box will be displayed.

of the toolbar for ediing ladder. The following

4 ・6

will be displayed, and the cell cursor will move to the right cell.


12. Move the cell cursor to the row number 000001 , and after inputting A contact (00001) as the

same way as the order No.4 and No.5, move the cell cursor on the A contact (00001).

13. Click . A contact (00001) will be connected by OR (OR connection).

14. Circuits between lines 2 and 3 are similar to the circuits of the lines between 0 and 1, so

create first the copy of the circuits between lines 0 and 1.

First, move the mouse cursor to the line number 000000, and drag the cursor to the line

000001.

15. Click [Edit]-[Copy] of the menu bar.

Click here

4 ・7


16. Move the mouse cursor to the row number 000002.

Click here

18. If you double click on the contact where a relay number is changed, input of the relay number

will be possible.

19. After inputting the relay number ([1] [0] in case of 00010), if you press [Enter] key, the relay

number will be changed, and the cell cursor will move to the next contact.

20. Input the relay number continuously, and complete the circuit. In addition, input [C] [2] in

4 ・8


■ Inputting Timer and Counter

22. To input TMR instruction, click of the toolbar for editing ladder. The following [TMR

Instruction] dialog box will be displayed.

23. Setup TMR type, TMR No. and setup value as the following.

24. If you click [OK] button, TMR instruction will be input.

26. When inputting CNT instruction, click of the toolbar for ediing ladder.

The following [CNT Instruction] dialog box will be displayed.

4 ・9


27. Setup CNT type, CNT No. and setup value as the following.

28. If you click [OK] button, CNT instruction will be input.

■ Inputting Application Instruction

30. When inputting application instruction, click of the toolbar for ediing ladder.

The following [Select Application Instruction] dialog box will be displayed.

31.There are two types of input methods for application instruction ：a method to select the

instruction or a method to input the instruction number. Here, we input the instruction number.

First, input [F] [6] [3] at the instruction input.

4 ・10


32. If you click [OK] button, [Timer/counter instruction] dialog box will be displayed.

33. After clicking [ ] , select [09000] and input [1] [0] [0]. Then you can assign the register

09100.

34. If you click [OK] button, F-63 (INC) instruction will be input.

35. After moving the cell cursor to the next line, (the next position is optional), if you click

button, [Select Application Instruction] dialog box will be displayed. Here we input F-40 (END)

instruction by the method of selecting the instruction. First, double click [Execution condition

instruction] at the general classification chart.

Double click here

Reference

33CUH1) of the program memory. Therefore, the calculation is executed even without writing it in, but if you write in F-40 (END) instruction right after a program has been created, the calculation time will be short.

4 ・11


36. Double click [END] at the detail classification chart.

Double click here

37.If you double click [End instruction [F-40]], the instruction at the instruction input will be

displayed.

Double click here

38.If you click [OK] button, [Execution condition instruction] dialog box will be displayed.

39.If you click [OK] button, F-40 [END] instruction will be input.

4 ・12


■ Program Check and Conversion to Mnemonic

Check the created ladder program and execute conversion of ladder to the mnemonic.

40. Click [Edit]-[Program Check] of the menu bar.

Click here

41. [Program Check] dialog box will be displayed, and click the appropriate item to mark the

check mark. Here all check marks are checked.

4 ・13


42. If you click [Start] button, the program check will start, and if there is a program error, an error

information at the message window will be displayed.

(Example of the program error)

←Over-using the output

00020 twice

If you execute the program check, it will also execute the conversion to the mnemonic at the same time. If there is an error like the disconnected circuit, an error information at the

[Compile error] dialog will be displayed.If an error occurs, modify correctly the program.

43. If you click [Display]-[Change Display] of the menu bar, it will change to the mnemonic

program display.

Click here

4 ・14


Reference If you click the button of the toolbar for editing ladder at the time when the ladder program display is being displayed, the conversion from ladder to mnemonic will take place. However, the

44. If you click of the toolbar for editing mnemonic, the conversion from mnemonic to ladder

will take place. If you click [Display]-[Change Display] of the menu bar right after, the ladder

program that is optimized to fit the window size will be displayed.

45. If you click [File]-[Save] of the menu bar, the dialog box to save the file will be displayed. Click

[Save] to save the program you have created.

Click here

4 ・15


4-3 PC Transfer/////Monitor

Transfer the created ladder program to PC (JW-33CUH1), and execute the monitoring of data.

1. Click [Setup]-[Communication Setup] of the menu bar.

2. [Communication Setup] dialog box will be displayed, and select [PC itself]. Match the port

number of [COM.Port] to the port number of the personal computer.

3. If you click [Setup in Detail] button, [Setup COM Baud Rate] dialog box will be displayed.

“high speed (115.2kbps)” button, click [OK] button at

[Communication Setup] dialog box, and the setup communication will be completed.

5. When the PC is running, stop the PC. Click [PC]-[Start/Stop] of the menu bar, and the following

dialog box will be displayed.

Click here

6. Click [OK] button. Verify that it has been stopped at the RUN lamp of the PC.

4 ・16


7. Click [PC]-[PC Transfer]-[Write] of the menu bar.

Click here

[OK] button, it will start the transfer (Here, only the program is being transferred.)

9. When the transfer is completed, the following dialog box will be displayed, and click [OK]

button.

10. Click [PC]-[Start/Stop] of the menu bar, the following dialog box will be displayed.

Click here

11. Click [OK] button. Verify that it has been running at the RUN lamp of the PC.

12. Click [Display]-[Changes Type of Monitor] of the menu bar.

Click here

4 ・17


13. [Setup Monitor Display Mode] dialog box will be displayed, and setup as the following. Click

[OK] button.

14. If you click [Monitor]-[Start Monitoring] of the menu bar, the ladder monitor will start.

Click here

Thick line represents the condition of running through.

Thin line represents the condition of not running through.

Current value ：BCD

Current value ：decimal

15. If you click [Monitor]-[Stop Monitoring] of the menu bar, the ladder monitor will stop.

Click here

4 ・18

4-4 Print

Print the created ladder programs.

1. Click [File]-[Page Setup] of the menu bar.


Click here

2. [Ladder Print] dialog box will be displayed, and change the setups according to each needs.

Here, we setup the following, and click [OK] button.

3. If you click [File]-[Print Preview] of the menu bar, the print image will be displayed.

Click here

4 ・19


Clicking [Zoom In] button makes the display larger, and clicking [Zoom Out] button will make the display smaller.

4. If you click [Print] button, [Print] dialog box will be displayed.

5. Click [Properties] button, and after changing the setup according to the need, click [OK] button.

6. If you click [OK] button at the [Print] dialog box, it starts printing.

4 ・20

■ The Print Example


4 ・21

Chapter 5 Menu Operation (File)

Chapter 5 Menu Operation

The operation of each menu of the menu bar of the main window and the basic window (program ：ladder/ program ：mnemonic/system/data/symbol/parameter) are explained.

The menu bar varies according to the window.

・Main Window

Menu Bar

(Details in pages) 5-3 5-30

・[Program : Ladder] window

Menu Bar

5-31 5-46 5-59 5-73 5-82

(Details in pages) 5-3 5-12 5-29 5-30 5-31 5-46 5-59 5-73 5-76 5-82

5 ・1


・ Menu bar of [Program : Mnemonic] window

(Details in pages) 5-3 5-12 5-29 5-30 5-31 5-46 5-59 5-73 5-76 5-82

・ Menu bar of [System/Data/Parameter] window

(Details in pages) 5-3 5-12 5-30 5-31 5-46 5-59 5-73 5-76 5-82

・ Menu bar of [Symbol] window

(Details in pages) 5-3 5-12 5-31 5-46 5-59 5-73 5-76 5-82

5 ・2


5-1 File

(Main/Program/System/Data/Symbol/Parameter)

If you click [File] at the menu bar of each window, [File] menu summary will be displayed.

・Main

(Details in pages)

5-4

5-6

5-9

〃

・Program/System/Parameter

(Details in pages)

5-4

5-6

5-7

5-8

〃

5-9

〃

〃

〃

〃

〃

・Data/Symbol

(Details in pages)

5-4

5-6

5-7

5-8

〃

5-11

5-10

5-9

〃

〃

〃

〃

〃

5 ・3


■ New


(1) Function

Create a new file.

(2) Operation content

① Click [File]-[New] from the menu bar

⇒ [New] dialog box will be displayed.

②

Example for

display

③

④

② Input the file name.

③ Determine the folder where you will create the file.

Click [Browse]. and the [Browse for Folder] dialog box will be displayed.

１

２

1 . Select the folder.

2 . Click [OK].

Notes

・ This software cannot open more than one files at the same time. If you try to create a new file while another file is open, a message "Do you close a File?" will be displayed.

⇒ If you click [No], JW-100SP starts.

⇒ If you click [Yes], the dialog box to save the current file will be displayed. After saving the file,

you can create a new file in the [New] dialog box.

5 ・4

④ Click [OK] of [New] dialog box

⇒ The [Select PC Model] dialog box will be displayed.

⑤ Setup the model

1 . Click [▼] of select series

⇒ series summary will be displayed.


2. Click the series name that you are going to select.

⇒ Selected model summary of the series will be displayed under "Model Selection" chart.

Series Selection Model Selection

JW20/20H JW-21CU(H),JW-22CU(H)

JW50/70/100

JW50/70/100H

JW30H

Remark

JW-100CU,W-50CU,JW-70CU

JW-100CUH,JW-100CUH (Expansion relay)

JW-50CUH,JW-70CUH

JW-31CUH,JW-31CUH1

JW-32CUH,JW-32CUH1(15.5K)

JW-32CUH1(31.5K),JW-32CUM1

JW-33CUH,JW-33CUH1

JW-33CUH2,JW-33CUH3

・ Select JW-32CUH1 for

JW-32CUM1.

JW10

W100

W70/100H

W16/51

J-board

JW-1324K/1342K

JW-1424K/1442K

JW-1624K/1642K

ZW-1K0CU/1CU/2CU/3CU

ZW-1HCU,ZW-70CU

ZW-160CU

ZW-501CU/CU2/CU3

Z-311J/312J/313J

Z-511J,Z-512J

・ Select JW-32CUH1 for Z-512J.

VME Built-in

Controller

JW-32CV1/32CV2

All All models (displayed above)

・The setup of the model at the time of shipment is JW100H(JW-100CUH).

3. Click the model name that you are going to select.

⇒ The model that is selected at "Current Model" chart will be displayed.

4. Click [OK]

⇒ Windows will be created in order, and the whole screen of the ladder window will be

displayed at the end.(refer to the next page)

5 ・5


・ Display example of ladder window

■


(1) Function

Open the existing file (program, system memory, data memory, symbol/comment, parameter).


① Click [File]-[Open] from the menu bar

⇒ [Open] dialog box will be displayed.

②

④

⑤

(Example for display)

5 ・6

③

② Select the directory at "Look in"

③ Select the kind at "Files of type" box


File Type

JW100SPfile (*.pgm, *.syc, *.dfi, *.sys, *.prm), Program(*.pgm), System(*.sys),

Data(JW100SP type)(*.dfi), Symbol/Comment(JW100SP type)(*.syc), Parameter(*.prm)

・For classification and extension of the file, refer to the page 3-3.

④ Select the reading file

⇒ file that was selected at "File name" chart will be displayed.

⑤ Click [Open]

⇒ open the window of the selected file

Notes

・In JW-100SP, you can open only one file per file type: Program, System, Data, Symbol, and Parameter.

Also, by selecting the tab of the tree bar, you can change the windows.

■ Close

(Program/System/Data/Symbol/Parameter)

Close the window of the opened file (Program/System/Data/Symbol/Parameter).

A conformation dialog box to save the file will be displayed before closing the window if the file has been modified.

・If you close the window without saving, all modified content after it was last saved will be lost.

5 ・7


■ Save


Save the currently active file without changing its name or its saved place.

If the file has been modified after it was saved last time, the confirmation dialog box will be displayed.

・If you are saving by changing the name and the place of the saved file, use [Save As] of the [File] menu.

■ Save As


(1) Function

Save the currently operating file by putting a new name .


① Click [File]-[Save As] from the menu bar.

⇒The [Save As] dialog box will be displayed.

②

③

⑤

④

② Determine the folder where you will save the file.

⇒Click [Browse]. and the [Browse for Folder] dialog box will be displayed.

１

２

1. Select the directory.

2. Click [OK].

③ Input the file name.

④ Select the file type.

⑤ Click [OK].

⇒The file will be saved.

5 ・8


■ FD Verify


Verify the files in operation with the files saved in the hard disk or floppy disk.

■


Setup the format of the page for printing..

⇒ For details, refer to "Chapter 9 Print."

■


Print the content of the open window.


■


Display the content of the open window as if printing.


■


Setup the selection and the connection of the printer.


■


Quit JW-100SP.

A confirmation message will appear as to save the modified file before quitting the operation.

・If you close the window without saving, all contents that were modified since the last saving will be lost.

5 ・9


■ Export Files (Data/Symbol)

(1) Function

Save the file about data memory or symbol/comment, specifying the file format.

(2) Operation

① Click [File]-[Export Files] from the menu bar.

⇒ The [Export Files] dialog box will be displayed.

②

④

② Determine the folder where you will save the file.

③ Select the file type.

③

⑤

File Type

Data memory

Symbol/Comment

File Format

Data JW100SP type(*.dfi), Data JW50SP type(*.dat),

File JW50SP type(*.fil)

JW100SP type(*.syc), JW50SP V5.0 type(*.sye),

JW50SP V4.0 type(*.sym), Text type(*.txt), ZM70 type(*.mg)

- For the detail of file type and extension, refer to page 3-3.

④ Input the file name.

⑤ Click [Save].

⇒ The file will be saved.

5 ・10

■ Import Files (Data/Symbol)

(1) Function

Import the file about data memory or symbol/comment.

(2) Operation

① Click [Import Files] of the [File] menu.

⇒ The [Import Files] dialog box will be displayed.

②


④

② Determine the folder where the file you will import is located.

③ Select the file type.

③

⑤

File Type File Format

Data memory (*.dfi, *.dat, *.fil)

Data JW100SP type(*.dfi), Data JW50SP type(*.dat),

File JW50SP type(*.fil)

Symbol/Comment (*.syc, *.sye, *.sym, *.txt, *.mg)

JW100SP type(*.syc), JW50SP V5.0 type(*.sye),

JW50SP V4.0 type(*.sym), text, ZM70 type(*.mg)

- For the detail of file type and extension, refer to page 3-3.

④ Input the file name.

⑤ Click [Save].

⇒ The file will be imported.

5 ・11

Chapter 5 Menu Operation (Edit)

5-2 Edit


If you click [Edit] at the menu bar of each window, the edit menu summary will be displayed.

(Details in pages)

5 -13

〃

〃

〃

〃

5 -14

5 -17

〃

〃

5 -18

〃

〃

〃

5-19

5-20

5-21

5-24

5-25

5-26

5-27

・Program：Ladder

(Details in pages)

5-13

5-18

〃

5-19

5-21

5-24

5-25

5-14

5-17

〃

〃

〃

〃

〃

・Program：Mnemonic

(Details in pages)

5-13

〃

〃

〃

5-14

5-17

〃

・System/Data/Parameter

(Details in pages)

5-13

〃

〃

〃

5-14

5-17

〃

5-27

・Symbol

5 ・12


■


Cancels the editing that has just been executed, and bring back the same cell /row as before.

・According to the operation content, there are items that you can not cancel.

■


Delete the selected cell/row and saves it momentary.

・Assign the cutting area before executing this operation.

・If you cut the cell/row, the content that was momentary saved will be replaced by the new content.

・In the program (ladder) window, the OR line (vertical) within the area will be out, but the OR line on the area will remain.

Also, you can not cut the part of the instruction such as the application instruction that uses several cells.

・In windows of system /data /parameter, only the data in the selected area will be 0 cleared. however, in case of the system window, there is a part of the area you can not cut.

・In the symbol window, you can delete only the symbol/comment in the selected area.

・Refer to pages 6-24 to 6-25 (moving circuit) for the use example of the program (ladder) window.

■


Copy the selected cell /row, and saves it momentary.

・Assign the copying area before executing this operation.

・If you copy the cell /row, the content that was momentary saved will be replaced by the new content.

・In the program (ladder) window, the OR line (vertical) within the area will be copied, but the OR line on the area will not be copied.

Also, you can not copy the part of the instruction such as the application instruction that uses several cells.

・In windows of system/data/parameter, only the data in the selected area will be saved momentary.

・In the symbol window, you can save only the symbol/comment momentary in the selected area.

・Refer to pages 6-23 (copying circuit) for the use example of the program (ladder) window.

■


Paste the momentary saved content from "cut"/"copy" operations to the assigned position.

・Complete "cut"/"copy" operations before executing this operation.

・When pasting, select "cell" if the saved content is cell, and select "row" if the saved content is row.

・In system /data /parameter window, data of the selected address will be replaced

withthe momentary saved data by "cut"/"copy" operations.

However, in case of the system window, there is a part of the area you can not paste.

・In the symbol window, the symbol/comment of the selected address will be replaced with the mo

mentary saved symbol/comment by "cut"/"copy" operations.

・Refer to pages 6-23 (copying circuit) for the use example of the program (ladder) window.

■

(Program Ladder)

Save the ladder program as an image file of the bitmap format in the clipboard.

・You can paste it in the Excel or Word document.

5 ・13


■


Assign the character line (address, instruction, symbol) in the selected file, and search.

There are two types of search methods: "Find for the first time" and "Find continuously."

[1] Find for the First Time

When searching a character string for the first time, input it in the [Find] dialog box. When the dialog box appears, the address or data of the selected area of the current file is automatically input in the

[Find What] area.


① Click [Find] of the [Edit] menu. (Refer to the page 5-12)

⇒ [Find] dialog box will be displayed.

・Program

③

②

⑤

④

・System/Data/Symbol

③

②

・Parameter

③

②

⑤

④

⑤

④

5 ・14


② Select of "Item to find"

According to the operation window, the object of search varies. (You cannot search the item other than search objects.)

Item to find Program System Data /Symbol Parameter

Address,

Constant

Relay,Register

Instructions

Symbol/

Comment

Distinguish the uppercase and lowercase

STR, AND, etc.

Symbol, Comment,

Line comment

Symbol, Comment,

Line comment

File 8, 9

Search without distinguishing file 8 and 9

System memory Relay,Register

Comment

―

―

―

―

Symbol, Comment

Symbol, Comment

―

Parameter

―

―

―

―

③ Input the strings

Item to find

Address

Constant

(Relay,

Register,

Setting value)

Instructions

The input content of the character line

・When inputting the character line, there aren’t any distinctions between the upper or lower case characters.

・When the high figure of the number is 0, like the relay address, you can omit the zero..

(Example) 1. The valid character line when finding relay 00122

122, 00122

2. The valid character line when finding register ]0123

]123 (] of bracket)

3. The valid character line when finding register 89001

89001

・When inputting the character line, there aren’t any distinctions between the upper or lower case characters.

・When the high figure of the number is 0, like the relay address, you can omit the zero..

(Example) 1. The valid character line when finding STR 00123

STR00123, str00123, Str123

2. The valid character line when finding application instruction

Fc012, Fc012, fc12

Strings

(Symbol,

Comment,

Line comment)

・In the window other than the program one, uppercase and lowercase characters are always distinguished.

・In the program window, you can define whether to distinguish uppercase and lowercase characters. symbol LS01

Program window: LS1, ls1, ls01

Other windows: LS1, LS01

④ Select search direction

From the beginning: Search from the beginning of the file.

To Top: Search from the cursor to the beginning of the file.

To Bottom: Search from the cursor to the end of the file.

⑤ Press the [Enter] key, or click [Find Next]

⇒ It starts finding, and the cursor moves to the found cell or row.

5 ・15


[2] Find Continuously

In case of finding the character line that was once found, use the "Find history."

・Once found character line will be added to the "Find history" combo box.


①

(Display example of the program)

① Click [ ▼ ] of the "Find history."

⇒ Display the once found character line summary.

③

②

④

② Click the character to find

⇒ It is displayed on the combo box of "Find history."

③ Click (Find next) or ④ (Find previous)

⇒ It starts finding.

・ "Find" is also executed when you click [Find Next] or [Find Previous] of the [Edit] menu.

Notes

・There are no limit in the number of the character lines stored in "Find history." Also, once stored character lines will not be deleted. When this software is terminated, all the character lines will be cleared.

5 ・16


■ Find Previous


Find already assigned character lines towards forward in the selected file.

・Select the character line from "Find history" summary of the sub toolbar.

・Refer to the previous page for the operation method.

■ Find Next


Find already assigned character lines backwards in the selected file.

・Select the character line from "Find historys" ummary of the sub toolbar.

・Refer to the previous page for the operation method.

■ Find Coil

(Program)

Find the output (coil) that uses the relay address of the cursor position in the selected file.

・It starts finding from the cursor position towards the gaining direction of the program address, and

if nothing is found, it starts finding from the program address 0 to the cursor position.

(Find example)

Find coil

The cursor moves to the found coil.

5 ・17


■ Insert Cell

(Program ：Ladder)

Insert the cell in the assigned position.

・You can select several cells.

・All cells that are right of the inserted position will move to the right direction the same amount of

columns of the cell inserted.

・Refer to the page 6-21 for the use example.

■ Insert Row

(Program)

Insert the row in the assigned position.

・ All rows that are below the inserted position will move down the same amount of the inserted rows.

・If there is an instruction like the counter instruction /application instruction that occupy several rows,

you can not insert the row.

・ Refer to the page 6-21 for the use example.

■ Delete Cell

(Program：Ladder)

Delete the cell of the assigned position.

・You can select several cells.

・ All cells that are right of the deleted position will move to the left direction the same amount of columns

of the cell deleted.


■ Delete Row

(Program)

Delete the assigned row.

・ All rows that are below the deleted position will move upward the same amount of the deleted rows.

・If there is an instruction like the counter instruction /application instruction that occupy several rows,

you can not delete the row.


5 ・18


■

(Program)

Make the assigned line to the line comment.

・An input box is displayed in the row, so that you can write in the comment.

・The character number of the line comment is 100 characters.

・A Row that become the line comment becomes NOP instruction inside the PC.

・Rows during the network can not become line comments.

・ In the ladder, you can insert the line comment in the row where the ladder circuit exists, but in the

mnemonic, you can only create the line comment in the program address of the NOP instruction.

(Example)

Ladder program

After selecting the row number with the cursor, click [Edit]-

[Create Line Comment]. Then, t h e l i n e c o m m e n t w i l l b e inserted. After inputting the comment character, establish the command with the [Enter] key.

Mnemonic program

← Inside the PC, it becomes the NOP instruction.



5 ・19


■

(Program : Ladder)

Enlarge /contract the window display of the ladder program.

(1)

(2)

(1) Zoom (+)

Enlarge 1 rank up the window display of the ladder program.

・Enlargement rates are: 113%, 125%, 138%, 150%, 163%, 175%, 188%, and 200%.

・You can enlarge, for example, from 88% → 100%.

・You can select from the magnifying power chart of the sub toolbar.

(2) Zoom (–)

Contract 1 rank down the window display of the ladder program.

・Contraction rates are: 88%, 75%, 63%, 50%, 38%, and 25%.

・You can contract, for example, from 150% → 125%.

・ You can select the contraction rate from the magnifying power chart of the sub toolbar.

5 ・20


■ Jump

(Program)

Move (jump) to the assigned row. There five types for ladder and four types for mnemonics.

(Menu of ladder)

(1)

(2)

(3)

(4)

(5) *

* "To Program Address" (5) is not for mnemonics.

(1) To Top Row

Move to the front of the window.

(2) To Unedited Row

In case of the ladder, it moves to the unwritten row, and in case of the mnemonic, it moves to the

NOP instruction.

(3) To Assigned Row

Moves to the assigned row number by the [Jump to Assigned Row] dialog box.

5 ・21


(4) To Address Mark

If you select the address mark that was setup already by the [Go to Address Mark] dialog box , it

moves to the row where the address mark was added.

You can add address mark in the optional row of a window.

① Adding method

If you click in the area of row selection, the address mark will be displayed on the left of the row.

Address mark Area of row selection

・If you double click in the row that contains the address mark, the address mark will be deleted.

・You can also add the address mark to the row which was assigned as the line comment.

② Number of address marks

You can add maximum 256 address marks.

③ Using method

If you click [Jump]-[To Address Mark] by the [Edit] menu, [Go to Address Mark]

dialog box will be displayed.

・ If you click [Go to] after selecting the address mark, it moves to the row containing this assigned mark.

・ The line comment is also displayed, so that it is useful to add the address mark to the line comment.

5 ・22


(5) To Address Mark

Move to the address specified in the [Jump to Program Address] dialog box.

■

(Program : Ladder)

In the library window, "Create library," "read file," and "save file" operations are executed. This operation is executed under the [Library] of the [Edit] menu.

・Program:Ladder

Item

Read

Register

Content

If you click [Library]-[Read], the library window will be displayed. In addition, in the library window, if you click [File]-[Read], [Read from library] dialog box will be displayed. The file is selected in this dialog box, and the file will be read.

・It can read the file that was setup in the same model as the library window.

Also, the file that can read is only the library file that carries the extension LB2.

If you click [Library]-[Register] after selecting the register area at the program ： ladder window, the library window will be displayed under the condition of the select area being copied. If you click [File]-[Save As] at this window,

[Register library file] dialog box will be displayed. Save it with the file name.

Refer to "Chapter 6 Program Edit" for more details on the library.

5 ・23


■ Program Check

(Program)

(1) Function

Check the grammar and the format of the program

The following are the check items.

Check item

Stack use condition

MCS /MCR use condition

JCS /JCR use condition

Double use of the output instruction

Double use of TMR /CNT /MD instruction

Use condition of ONLS /ONLR

Use condition of Label

Use condition of FOR /NEXT instruction


① Click [Edit]-[Program Check] of the menu bar.

⇒ [Program Check] dialog box will be displayed.

②

③

② Select the check item

Click the check box that contains the item to check.

⇒ The check mark will be displayed.

③ Click [Start] button

⇒ The program of the check item will be checked.

・The check result will be displayed at the message bar window.

5 ・24


■ Converts Data in Batch

(Program)

(1) Function

The whole program including relay /timer /register /label number are modified in batch.


① Click [Edit]-[Converts Data in Batch] of the menu bar of the program

⇒ [Converts Data in Batch] dialog box will be displayed.

③ ④

②

② Select the item to convert

⑤

Select the kinds (Relay, TMR /CNT, Register, Label) for conversion data in batch.

③ Setup the address

Setup the start (front) address, end address, the front address of the destination address of the

relay /register, etc.

④ Select "Is Added /None" of the "Converts Symbol"

In case of changing the symbol/comment at the same time, select "Is Added", and in case of not changing the symbol/comment, select "None."

If you setup "Is Added," the address of the symbol /comment that attaches to the address will also be changed at the same time.

⑤ Click [Exec.] button.

⇒ Data in batch are changed.

(3) Conversion example

Before the Conversion

Converts data in batch

After the Conversion

Items to convert ：Relay

Start address ：100

End address ：101

Destination ：200

Converts symbol ：None

5 ・25


■ Replacing Contacts

(Program : Ladder)

(1) Function

Interchange A contacts with B contacts in the specified relay address, and vice versa, about the

program in operation.


① Click [Replacement No and Nc] of the [Edit] menu in the menu bar of the program:ladder.

⇒ [A Contact B Contact ] dialog box will be displayed.

②

③

② Determine the relay address whose contacts will be interchanged.

⇒ If you select a contact in the program window in operation, the related relay address will be

automatically displayed.

③ Click [Execute].

⇒ The [Result] dialog box is displayed, and you can see how many contacts have

been interchanged.

(Example) When you have replaced the contacts in the relay address 12000

5 ・26


(1) Function

When creating the ladder program, assign the symbol which was temporarily registered by the

symbol input, to the actual address.


① Click [Edit]-[Assign Symbol] of the menu bar

⇒ [Assign Symbol] dialog box will be displayed.

④

②

③

(Display example)

Item

Symbol

Type

Address

Content

Display the temporary registered symbol.

Display the temporary registered data memory classification (relay /register, etc.) of the symbol.

If you assign the address to the symbol, the address will be displayed.

② "Double click the row of the assign operation" or "Input [Enter] key after selecting the row of the

assign operation"

⇒ Open the box for input on the address chart.

③ Input address

② Click to the right of the mouse after selecting the row of the assign operation

⇒ The select menu will be displayed.

・Type : at the time of relay ・Type : at the time of register

③ Input the address after selecting the item of the address

5 ・27


④ Click [File]-[OK]

⇒

(Display example)

・ The symbol assigning the address will be registered in the symbol/comment window.

・ The progress of the register will be displayed at the message bar.

・ The symbol that completed the registration will be deleted from the list of [Assign Symbol] dialog box.

・ Until you click [OK], the symbol assigning the address remain temporary registered.

(3) Assign example

Before assigning the symbol

Display Type ＝

(But the input symbol is: Display Type ＝at the )

Assign symbol

After assigning the symbol

Display Type ＝

5 ・28

Chapter 5 Menu Operation (Instruction)

5-3 Instruction

(Program)

If you click [Instruction] at the menu bar of the [Program] window, [Instruction] menu summary will be displayed.

・Program：Ladder ・Program：Mnemonic

Menu item

A contact

B contact

Horizontal line

Vertical line

STR

NOT

AND

OR

OUT

TMR

CNT

FUN

F43

F44

F45

F-20 (MD)

Content

When editing the ladder, Input A contract.

When editing the ladder, Input B contract.

When editing the ladder, Input horizontal line.

When editing the ladder, Input vertical line.

When editing the mnemonic, input STR, STR NOT, AND STR, OR STR instruction.

When editing the mnemonic, input STR NOT, AND NOT, OR NOT instruction.

When editing the mnemonic, input AND, AND NOT, AND STR instruction.

When editing the mnemonic, input OR, OR NOT, OR STR instruction.

Input OUT instruction (coil).

Input TMR instruction.

When editing the mnemonic, it's also used as the input of TMR contact.

Input CNT instruction.

When editing mnemonic, it's also used as the input of CNT contact.

Input the application instruction.

Input F-43 instruction (reverse bit).

Input F-44 instruction (differential ON).

Input F-45 instruction (differential OFF).

Input F-20 instruction (MD).

・If you click［F-20 (MD)］, ［Input F-20 (Maintenance display)］dialog

box will be displayed.

Refer to “Chapter 6 Program Edit” for the detail on the instruction input.

5 ・29

Chapter 5 Menu Operation (Monitor)

5-4 Monitor

(Main/Program/System/Data/Parameter)

If you click [Monitor] at the menu bar of each window, [Monitor] menu summary will be displayed.

・Main ・Program : Mnemonic/System/Data/Parameter

・Program : Ladder

Menu item

Start Monitoring

Stop Monitoring

I/O Force Processing

Edit Circuit

Content

Start the monitoring.

Stop the monitoring.

Select either ON/ OFF of the relay of the PC by force.

Modify, insert, or delete the program of the PC, or interchange the contacts, during the monitoring.

Refer to "Chapter 8 Monitor" for the details on the monitor.

5 ・30

Chapter 5 Menu Operation (Display)

5-5 Display

(Main /Program /System /Data /Symbol /Parameter)

If you click [Display] at the menu bar of each window, [Display] menu summary will be displayed.

・Main

(Details in pages)

5 -33

〃

〃

〃

〃

〃

・Program：Ladder

(Details in pages)

5 -34

〃

5-35

5-36

5-37

5-38

5-42

5-33

〃

〃

〃

〃

〃

・Program：Mnemonic

(Details in pages)

5-34

5-36

5-38

5-43

〃

〃

5-33

〃

〃

〃

〃

〃

・System

(Details in pages)

5-43

〃

〃

〃

〃

5-44

〃

〃

5-45

〃

5-33

〃

〃

〃

〃

〃

・Data

(Details in pages)

5-43

〃

〃

〃

〃

5-44

〃

〃

5-45

〃

5-33

〃

〃

〃

〃

〃

5 ・31


・Symbol

(Details in pages)

5-43

〃

〃

〃

〃

5-44

〃

〃

5-45

〃

5-33

〃

〃

〃

〃

〃

・Parameter

(Details in pages)

5-33

〃

〃

〃

〃

〃

5 ・32


■

Ladder / Toolbar for Editing Mnemonic /Toolbar for Editing Data /

Message Bar


Select "yes /no" of the display of each bar at the window. When "yes" is selected, a check mark is displayed besides each bar name.

・In case of [Program : Ladder] window

①

②

④

⑤

⑥

③

・In case of [System] window

①

②

⑦

④

⑥

③

① : Main Toolbar

② : Sub Toolbar

③ : Status Bar

④ : Tree Bar

⑤ : Toolbar for Editing Ladder

In case of [Program : Mnemonic] window, the toolbar for editing

mnemonic will be displayed at this position.

⑥ : Message Bar

⑦ : Toolbar for Editing Data

5 ・33


■

(Program ：Ladder)

Select display type of the address/symbol/comment at the ladder program.

・Program : Ladder

Item

Normal

Symbol

Comment (8c, 4l)

Comment (16c, 2l)

Content

Only the address will be displayed.

" ＊＊＊＊＊" will be displayed if it’s not input at the symbol, and the address is not assigned. (Symbol assigning method⇒ refer to the page 5-27)

If the symbol is setup, the symbol will be displayed. Also, all address inputs are executed with the symbol. (Symbol input ⇒ refer to the pages 6-8, 6-15)

If the comment is set up, the comment will be displayed in 8 characters by 4 lines. You can input the comment when inputting the address.

If the comment is set up, the comment will be displayed in 16 characters by 2 lines. You can input the comment when inputting the address.

Full (Address/

Symbol/Comment)

When it is set to Address, you can also see the symbol or comment. You can input the symbol/comment when inputting the addres.

・Refer to the page 6-2 about the example for display.

■

(Program)

Change between the ladder window and the mnemonic window.

・When changing, if one of the windows has been edited after the last transformation, a confirmation

message asking either "from ladder to mnemonic" or "from mnemonic to ladder" will be displayed.

Ladder window

View Change

Mnemonic window

5 ・34


■

(Program : Ladder)

(1) Function

Assign (select) the monitor type during the monitor at the ladder window.

Item

Type of Monitor

Display Mode

Type of Register

Display Mode

Effective Area of

Type of Register

Display

Content

Select the display type (simple display /detail display) of the application instruction.

◎Simple Display

Only the current value will be displayed at the register of the application instruction.

All current values of the register are displayed by the notation that was selected at

the "type of register display mode."

The current value of the byte /word treatment instruction will be displayed as byte

/word, but the current value of the double word treatment instruction will be

displayed in word. (only the lower words are displayed.)

◎Detail Display

Display the current value and the notation in the register of the application

instruction.

You can select the "effectire area of type of register display mode."

The current value at the byte /word /double word treatment instruction will be

displayed in byte /word /double word display.

Select the notation display type of the register during the application instruction from

HEX (hexadecimal notation), DCML(decimal notation), OCT(octal notation).

Select the effective area of the notation display which was selected at the "type of register display mode." If the "tye of monitor display mode" is the "easy display," you can not select. In this case, it will be "all registers."

◎All Registers

Display the current value by the notation selected at the "type of register display mode" to all the registers during the application instruction.

◎Infinitive Register of Number Type

Only the register of the undecided value type during the application instruction will

display the current value by the notation selected at the "type of register display mode."

The register during the instruction (F-08［transfer of octal notation］etc.) whose value type has been established will display the current value by the notation of the value type.

Example 1) Type of monitor display mode : simple display, type of register display mode : DCML

Decimal notation display



Example 2) Type of monitor display mode : detail display, type of register display mode : DCML,

effective area of type of register display mode : infinitive register of number type

Decinal notation display

(the register with undecided

numerical value type)


(the register with established


Octal notation display

(the register with established


5 ・35



① Click [Display]-[Changes Type of Monitor] of the menu bar of the program：ladder

⇒ [Setup Monitor Display Mode] dialog box will be displayed.

② Select type of monitor display mode. Select from

either "Simple Display" or "Detail Display." ②

③ Select type of register display mode

Select from "HEX" (hexadecimal notation),

"DCML" (decimal notation),"OCT" (octal notation).

③

④ Select effetive area of type of register display

When selecting "Detail Display," select either "All

④

Registers" or "The Infinitive Register of Number

Type."

⑤

⑤ Click [OK]

⇒ Selected content is registered.

■

(Program)

Change the display of the program memory (file8 /9).

・When the memory volume of the program exceeds 31.5K words, change the display between 00000 and 76777 (file8) and 100000 and after (file9) of the program address.

・File 9 is used as the destination of the divided branch created by the jump instruction (F-141,F-151), or used as the hangar of the sub routine program created by the sub routine call instruction (F-142,F-148).

Address

000000

076776

076777

File 8 File 9

F-141

JMP

LB0000

ＥＮＤ

JUMP

100000

176776

176777

F-140

LABL

LB0000

ＥＮＤ

Address

000000

076776

076777

File 8 File 9

F-142

CALL

LB0001

ＥＮＤ

CALL

100000

176776

176777

F-140

LABL

LB0001

F-143

RET

ＥＮＤ

・Each function such as program check, change from ladder to mnemonic, change from mnemonic to ladder, transfer to the main PC, save in the file, or print will be executed in batch at the file 8/9.

5 ・36


・Program：Ladder

Note:

You cannot edit the program when it is word-wrapped.

(1) Function

Display a ladder wrapped when it is longer than the width of the ladder window in operation.

(2) Operation

Click [Display]-[folding]-[On] in the menu bar of the program:ladder.

⇒ Display the ladder program wrapped.

5 ・37


■

(Program)

(1) Function

Display/print the using-condition chart of the relay, timer ･counter, register and label.

・The data list at the [Program : Ladder] window will be automatically changed to mnemonic

before the display. As a result, the circuit of the ladder program must be normal in order to display the data list.

If you click [Display]-[Data List] by the menu bar of the [Program : Ladder]/ [Program : Mnemonic] window, [Data List] dialog box will be displayed.

(Display example)

Item

Address

Content

Used address will display ※(××). ×× of (××) describes the number of addresses.

Display of ※ Content

− Use as Contact

＊

T

C

Use as Coil

Use as Timer

Use as Counter

Symbol

Comment

Displayed when the symbol/comment is registered at the address.

Cross reference

※××××× [−−−−] will be displayed.××××× describes the Program address, and −−−− describes the network (circuit) number.

Display of ※ Content

＊ Use as output

／ Use as B contact

Note that the network number will not be displayed at the [Program :

Mnemonic] window.

5 ・38


Explain the menu operation of the [Data List] dialog box.


⇒ Refer to the

next page

Item

Close

Page Setup

Print

Print Preview

Printer Setup

Content

Close the data list file that is being displayed.

Setup the format of the page for printing the data list.

・If you click [Page Setup], [Setup Print of Data List] dialog box will be

displayed.

Print the data list.

Display the image data list as if printing.

Setup selection /connection of the printer.

・If you click [Printer Setup], [Printer Setup] dialog box will be

displayed.

・For more details of printing data list, refer to "Chapter 9 Print."

5 ・39


Item Content

Assign the address to be displayed in the data list at the [Assign Address] dialog box. [Assign Address] dialog box will be displayed when this particular item is clicked.

Assign Address

Jump

Displays Again

・If you click [ ▼] and select the kinds of register, and click [OK] after inputting the address, the data list of the assign area will be displayed.

You can also assign the address by "double click the left side of the mouse" or by inputting the [Enter] key.

After selecting the program address of the cross reference display, if you click [View]-[Jump], the cursor will move to the instruction of the program address. Note that, you can also do the same operation by

"double click the left side of the mouse." the program address of the cross reference display.

Create again the data list for every program and display.

Assign the display type of the data list at the [Setup Display Type] dialog box. [Setup Display Type] dialog box will be displayed when this particular item is clicked.

Display Type

◎ Symbol Display

Select "Do / Undo" of the display of the symbol which is setup at relay /register. Select the item by clicking.

◎ Comment Display

Select "Do / Undo" of the display of the comment which is setup at relay /register. Select the item by clicking.

◎ Reference Display

1 Row : After the assigned address, display the cross reference of the

continuous address by each row.

Detail : Only the cross reference of the assigned address will be

displayed repeatedly inside the cross reference display area.

Undo : Cross reference is not displayed.

5 ・40


(3) Use example

← Network number 0




[Note] 1 comment line is 1 program address and 1 network.

Display type −Symbol Display : "Undo", Comment Display : "Undo", Reference Display : 1 Row

Assign Address : 00000

2 contact

1 coil

A contact

Network number

Program address

B contact Output

Assign Address ：TC0000

2 timer contact

Timer instruction

1 counter instruction

1 counter contact

5 ・41


■

(Program : Ladder)

(1) Function

You can optimize the following: the connection of the disconnected circuit of the created ladder circuit, adjustment of the display position of the output instruction (OUT instruction, /application instruction etc), re-arrangement of the MCS/JCS condition display,re-arrangement of the ladder diagram’s layout.

Item

Connection of

Disconnected Circuit

Content

Re-connect the disconnected circuit. Only the horizontal line can be connected, and you can not connect the vertical line.

Adjust the display position of the OUT instruction, TMR/CNT

Adjustment of Display

Position instruction, application instruction.

You can setup the display position by selecting the [Open] button inside the [Arrange Ladder Diagram] dialog box, or at the [Setup

Display Pattern] dialog box by clicking [Setup]-[Setup Display

Pattern] by the menu bar.

Arrangement of MCS JCS Check the valid area of the MCS(F-30), JCS(F-41)condition, and

Condition’s Display

Diagram’s Layout display "M" (MCS), " J " (JCS) to the row number of the valid area.

Re-arrangement of Ladder Omit unnecessary horizontal lines of the ladder circuit, and gather the ladder element to the left side.

・For more details of the display example etc., refer to the pages 6-35 to 37.


① Click [Display]-[Arrange Ladder Diagram]

by the menu bar of the program : ladder.

⇒ [Arrange Ladder Diagram] dialog box

will be displayed.

② Select item

Click the check box of the item to execute.

⇒ The check mark is displayed.

③ Setup screen

Click [Open] button when setting up the screen for adjustment of the display position.

⇒ [Setup Display Pattern] dialog box will be displayed.

The setup at the [Setup Display Pattern] dialog box is same as the setup at the [Setup]-[Setup

Display Pattern], so please refer to the page 5-57.

If you click [OK] at the [Setup Display Pattern] dialog box, or click [Cancel] button,

you will be back to the [Arrange Ladder Diagram] dialog box.

④ Click [Exec.]

⇒ Execute the item of the check mark.

5 ・42


■ Displays in Symbol/ Displays in Comment/ Displays in Symbol &

Comment

(Program/Mnemonics)

Change the display of symbol/comment.

Item

Add Symbol

Add Comment

Add Symbol Comment

Content

Display symbol

Display comment

Display symbol and comment at the same time.

■ Displays in Binary Notation /Displays in Octal Notation /Displays in

Decimal Notation /Displays in Decimal Notation (with +-)/Displays in

Hex Notation /Displays in ASCII

(System/Data/Parameter)

Select the display of data (Binary notation/Octal notation/Decimal notation/Decimal Notation (with +-)/

Hexadecimal notation/ASCII).

※

※ You cannot select

"Display in Decimal Notation (with +-) for System.

• The example on the left is in the case of "Data."

Item

Displays in Binary Notation

Displays in Octal Notation

Displays in Decimal Notation

Displays in Decimal Notation

(with +-)

Displays in Hex Notation

Displays in ASCII

Content

Displays data in binary notation.



Displays in decimal notation with a plus or minus sign.


Displays data in ASCII type.

5 ・43


■ Displays in Byte /Displays in Word /Displays in Double Word

(System/Data/Parameter)

Select the display of data (Byte/Word/Double word).

Item

Displays in Byte

Displays in Word

Displays in Double Word

Content

Displays data in byte module.

Displays data in word module.

Displays data in double word module.

5 ・44


■ Displays in Detail /Displays as a List

(System/Data)

Select the display of data from the detail or list.

Menu item

Detail Display

Displays in List

Content

Displays in one row, and symbol /comment is also displayed by the window.

Displays maximum data that can be displayed in the window in several rows.

Window

System

Data

Menu Item

Displays in Detail

Displays as a List

Displays in Detail

Displays as a List

Display Content

Address, Data, Comment

Address, Data

Address, Data, Symbol, Comment

Address, Data

・Displays in Detail

・Displays as a List

5 ・45

Chapter 5 Menu Operation (Setup)

5-6 Setup


If you click [Setup] by the menu bar at each window, [Setup] menu summy will be displayed.

・Main /Program : Mnemonic /System /Data /Parameter

(Details in pages)

5-46

5-47

5-48

5-54

・Program : Ladder

(Details in pages)

5-46

5-47

5-48

5-54

5-55

5-56

5-57

・Symbol

(Details in pages)

5-46

5-47

5-48

5-54

5-58

■ Select PC Model


(1) Function

Setup the PC model that will be the object of edit/monitor.

・You can only use one model at a time even you have opened several windows .


If you click [Model Setup] by the [Setup] menu, [Model Setup] dialog box will be displayed.

・Details on this operation is same as "New" (refer to the page 5-4).

5 ・46


■


(1) Function

Setup the volume of the program memory.

・Setup the memory volume of the PC model which has been setup.

(2) Operation content

If you click [Memory Capacity Setup] by the [Setup] menu, [Select Memory Capacity] dialog box will be displayed.

②

①

(In case of JW-100CUH)

① Click [▼]

⇒ Display the possible (for setup) memory volume summary of the model which has already been

setup.

(In case of JW-100CUH)

・Select the memory volume.

② Click [OK]

⇒ Setup the memory volume.

5 ・47


■


[1] Function

Setup the PC which will be the object of communication, or setup the communication port of the personal computer.

Communication object Operation Method

Operate the PC by connecting the unit between the personal computer and

PC itself

Network

Remote I/O

Modem

Ethernet

・When the model is JW30H, you can setup the communication baud rate.

Connect the personal computer to the network module/ ME-NET module , and operate the PC which is connected to the satellite net /ME-NET/SUMI-NET.

Connect the personal computer to the remote I/O slave station module

(JW-20RS), and operate the master PC that is connected to the satellite net.

Connect the personal computer to the network module through modem, and operate the PC.

Operate the PC connected to Ethernet.

[2] Operation Content

If you click [Communication Setup] by the [Setup] menu, [Communication Setup] dialog box will be displayed.

④

①

③

②

・ ① to ④ will be compatible to the following ① to ④.

(1) In case of connecting with the PC itself

① Click [PLC itself].

② Set up the communication port and timeout duration of the personal computer.

③ When the model is JW30H, click [Setup in Detail].

⇒ [COM Baud Rate Setup] dialog box will be displayed.

・ Select either standard communication baud rate (19.2kbps) or high speed (115.2kbps).

The possible combinations of the communication during the high speed are the PC that control module is JW-31CUH1/32CUH1/32CUM1/33CUH1/33CUH2/33CUH3, and it is limited to the personal computer that is compatible to 115.2kbps. If the personal computer is not compatible to 115.2kbps, select the high speed (115.2kbps). You will be then able to communicate by 19.2kbps.

④ Click [OK]

⇒ The setup will be completed.

5 ・48


(2) In case of network connection ( ① to ④ ⇒ corresponding to page 5-48)

① Click [Network]


③ Click [Setup in Detail]

⇒ [Setup in Detail] dialog box will be displayed.

Operation Item

Network

Configuration

Operation Content

Select from standard/expansion

Standard

Operate the PC of the other station that is connected to the

SATELLITE-NET/ME-NET/SUMI-NET (remote operation of one layer)

Expansion

Relay the optional station that is connected to the SATELLITE-

NET/ME-NET/SUMI-NET, and operate the PC of the other station that is connected to the SATELLITE-NET/ME-NET/SUMI-NET via the relay station. (remote operation of two layers)

Target Station

Setup the station number of the target station that will be the object of communicate and the kind of module.

Station No.

Kind of Module

0 to 77

(8)

SATELLITE-NET/ME-NET/SUMI-NET

Relay Station

When the network organization is the " expansion, " setup the station number/kind of module/rack number/slot number of the relay station.

Station No.

Kind of Module

Rack No.

Slot No.

0 to 77

(8)

SATELLITE-NET/ME-NET/SUMI-NET

0 to 7

0 to 15

・If you click [▼], the kind of module of the target station /relay station will be displayed in

summary.

④ Click [OK]


5 ・49


(3) In case of remote I/O connection ( ①∼④ ⇒ corresponding to page 5-48)

① Click [Remote I/O]


(The "setup detail" of ③ is not necessary)

④ Click [OK]


5 ・50


(4) In case of modem connection ( ①∼④ ⇒ corresponding to page 5-48)

① Click [Modem]


③ Click [Setup in Detail]

⇒ [Communication Setup] dialog box will be displayed.

Operation Item

Contact

TEL Number

Address book

Operation content

Input the name of company/person you will communicate, if necessary.

Input the telephone number of company/person/computer you will communicate. If you are using PBX (e.g. dial 0 to outside line), check the [Outside line] box.

You can register telephone numbers or other information in the address book.

You can register 100 contact numbers from #0 to #99. Information you have registered is imported to the [Communication Setup] dialog box when you select the telephone number and click [OK].

When you click the [Address book] button, the [Address book] dialog box will be displayed.

Input the number, name, and telephone number, and click [Add].

The information will beregistered in the address book.

To delete the information, select the number and click [Delete].

5 ・51


Operation Item

Time Out Times

Operation content

Set up the duration of communication timeout between the modem and

JW-100SP. The timeout duration varies, depending on conditions of the personal computer and the telephone line. Set it up according to the situation.

Telephone circuit Select the type of your telephone line (pulse or tone).

Setup Network

Refer to "Network Connection."

If you connect a new modem, set up the modem itself first.

When you click the [Setup Modem] button, the [Modem setting] dialog box will be displayed.

Modem setting

You need to set up the modem of both the PC and the personal computer.

Connect the modem to the personal computer with a straight cable of

RS-232C (usually attached to modem).

To set up the modem of the PC, select [PLC side]; to set up the modem of the personal computer, select [Computer side] and click [Sending]. To set up the modem optionally, select [Data sending].

④ Click [OK]

⇒ The setup is completed.

5 ・52


(5) In case of Ethernet connection ( ①∼④ ⇒ corresponding to page 5-48)

① Click [Ethernet]

(You do not have to use the communication port of ②. Its setting is disabled.)

③ Click [Setup in Detail].

⇒ [Communication Setup] dialog box will be displayed.

Operation Item

IP Address

Port No

Protocol

Bind Port

Operation content

Specify the IP address set in the contact unit.

Specify the port number set in the contact unit.

Specify the protocol set in the contact unit.

Set the contact unit to TCP_Passive or UDP. You cannot set it to TCP_Active.

Note: If you are using JW-50CM, only UDP is available.

Set up the port the personal computer is using.

If you do not specify, Windows automatically set it up.

④ Click [OK]


5 ・53


■


(1) Function

Initialize files(Program/System/Data/Symbol/Parameter) you are editing with this software.


If you click [Memory Clear] at the [Setup] menu, [Memory Clear] dialog box will be dis played.

①

②

① Assign the object of "memory clear."

Click the check box of program memory, system memory, data memory, symbol/comment , parameter, and assign.

② Click [OK]

⇒ The confirmation dialog box of initialization will be displayed.

・If you click [OK], already setup object (file) will be memory cleared.

5 ・54


■

(Program : Ladder)

(1) Function

Setup the input mode at the time of creating a program, serial input of address input, double click, enlarge/contract of the application instruction frame.

Operation Item Operation Content

Select " direct input " or " dialog input.

"

Select item Content

Input Mode

Inputs at

Display Directly

Inputs Using

Dialog

If you select the instruction from toolbar for editing ladder, instruction menu, function key, the number of relay address

/register address /timer ･counter address /application instruction will be initialized, and then it will be written directly into the selected cell position.

・It’s useful when inputting the relay address after writing the

drawing part of the ladder.

If you select the instruction from toolbar for editing ladder, instruction menu, function key, the dialog box that inputs the relay address /register address will be displayed.

・Instruction that does not require the input of address will not

display the dialog box, but it will be written onto the selected cell

position.

Serial Input of

Address

Double Click

Widen /Narrow

Application

Instruction’s

Frame

Select the condition after the inputting the relay address /register address etc.

Select item

Do

Content

The next element will automatically be on the waiting list for inputting address.

Undo The next element will not automatically be on the waiting list for inputting address.

Select the condition after double clicking at the instruction cell.

Select item (content)

Becomes Address Input.

Changes Instruction at Cell

For the application instruction frame of several instructions, select several operation contents at the time of enlarge/contract of the display frame to the vertical direction.

Select item (content)

Process with Row Data

Process Application Instruction only

・For more details, refer to the pages 6-4 to 17.

5 ・55



If you click [Setup Input Type] by the [Setup] menu, [Setup Input Type] dialog box will be displayed.

・Select "Input Mode," "Serial Input of Address", "Double Click," "Widen /Narrow Application

Instruction’s Frame" at each check box.

■ Setup Display

(Program : Ladder)

(1) Function

Assign the display position of the coil (OUT instruction), TMR /CNT instruction, application instruction.

Operation item Operation Content

Assign the display position of the coil (OUT) instruction.

Select item Content

Display Position

Align

Display Size

Specity

Position

If the setup of 【align position】 cell from the right of the screen will become the screen display position of the coil. If it is "align right", the first cell from the right of the screen will become the display position of the coil.

If the number of contacts of the horizontal direction are more than the screen size, the display position of the coil will be decided according to the number of contacts. (Coil display position will be set outside the screen.)

Assign the display position of the coil with the row number (0 to 61).

If the number of contacts of the horizontal direction are more than the screen size, the display position of the coil will be decided according to the number of contacts.

Align Position

Assign the display position of TMR /CNT, application instruction number.

Select item

Align Left

Align Right

Content

Set at the display position of coil (OUT instruction).

Set at the fourth position from the left of the display.

Character color Specify the color of symbol, comment (including line comments) or program address.

・For the setup example, refer to the page 6-36.

5 ・56



If you click [Setup Display Pattern] at the [Setup] menu, [Setup Display Pattern] dialog box will be displayed.

・Select either ""Display" or "Align" at each check box.

・If the "Display" is checked under "Specity Position",

input the row number (0 to 61).

・If you click the [Exchange] button of "Symbol,"

"Comment,"or "Program Address" under the Character

Color, the [Select of Colors] dialog box will be displayed.

Select the color you want to set, and click [OK].

■ Key Assignment

(Program:Ladder)

(1) Function

Set up the short cut key assignment when the ladder mnemonics is input.


Click [Key Layout] in the [Setup] menu. The [Key Layout] dialog box will be displayed.

① Select the combo-box of the ladder mnemonics you will assign the key to, and input the character or the key with the keyboard or select it in the drop-down list.

・The keys you can assign are A to Z (26 keys), 0 to 9 (10 keys), or F2 to F9 (8 keys).

② If you click the [Default] button, the setup information gets back to the default value (same as JW-

50SP).

③ Click [OK].


5 ・57


■ Check Input of Same Symbol

(symbol)

(1) Function

If there is the same symbol at the different data memory address when registering the symbol, select either do /undo for "check input of same symbol."


If you click [Check Input’s of Same Symbol] by the [Setup] menu, [Check Input of Same Symbol] dialog box will be displayed.

Select from the check box of "Check Input of Same Symbol."

Do ：If you input the same symbol, the dialog box of the confirmation for register will

be displayed. Click [OK] button for the register.

Undo：Register the symbol no matter what.

5 ・58

Chapter 5 Menu Operation (PC)

5-7 PC


If you click [PC] by the menu bar of each window, [PC] menu summary will be displayed.

(Details in pages)

5-59

5-62

5-62

5-69

5-72

■


If you click [PC Transfer] by the [PC] menu, [PC Transfer] menu will be displayed.

(1) Function

Transfer (write /read /verify) the program, etc, with the connected PC.

Item

Write

Read

Verify

Content

Write data of the program, etc to the PC.

・The Main window does not have this item.

Read data of the program, etc from the PC.

・In the Main window, input the file name, and determine the folder.

Verify data of the program, etc with the PC.

・The verifying area of the system memory is #200 to #256.

・You cannot compare symbol/comment.

・The Main window does not have this item.

5 ・59



If you click [Write], [Read] or [Verify] by the [PC Transfer] menu, [PC Transfer] dialog box will be displayed.

Dialog box when writing

②

①

You cannot select in case of "Verify".

③

① Assign the Target of PC transfer

If you click the check button of program memory, system memory, data memory, symbol/comment, parameter, they become the targets of PC transfer.

・You cannot select symbol/comment in case of [Verify].

② Input the filename, and determine the folder (valid only in [Write] of the Main window)

・In the Main window (when a file is not open), when the [PC Transfer Read] dialog box appears by selecting [PC Transfer]-[Read], the "File" item is enabled.

・If you click [Browse] on the right of [Directory], the [Browse for Folder] dialog box will be displayed.

1

2

1. Select the folder.

2. Click [OK].

5 ・60


③ Click [OK]

⇒ Start the PC transfer of the assigned object.

・If the object is the "data memory," [Select File] dialog box will be displayed before the transfer,

and you can assign the file number of the object of transfer.

・

You can observe the progression of transfer in the transfer dialog box.

5 ・61


■


(1) Function

Run /stop the connected PC.

・Check automatically the run /stop condition of the PC, and when the PC is "running," it stops, and when the main PC is "stopping," it runs.


Click [Start /Stop] by the [PC] menu of each window.

Click here

⇒ When the PC is running /stopping, the following confirmation dialog box will be displayed.

Running Stopping

If you click [OK] button, the PC will stop when "running," and the main PC will run when "stopping."

■


If you move the cursor to the [PC Operation] of PC menu, [PC Operation] menu will be displayed.

Model

JW20/20H

J-board (Z-311J/312J/313J)

JW50/70/100

JW50H/70H/100H

JW30H

J-board (Z-511J/512J)

JW10

W100

W70H/100H

W16/51

VME Built-in Controller

−

○

○

−

−

−

−

−

−

[1]

[2]

[3]

[4]

[5]

[6]

Item of PC operation

I/O search Secret CU Memory Clear Parity Check EEPROM I/O Table

−

−

−

○

○

−

−

−

○

○

○

○

○

○

○

○

○

○

○

○

○

−

−

○

○

○

−

○

○

○

○

○

−

−

−

○

○

−

−

−

−

○

−

−

○

○ : model of the operation object

5 ・62


[1] I/O Search

(JW50/70/100,JW50H/70H/100H)

(1) Function

Assign the rack number (the number of basic panel) /slot number and LED check the assigned

I/O module.

Also, it is possible to LED check the I/O module that corresponds to soon to be assigned data memory address.

Operation item

Assign methods

Rack / slot

Data memory address

Setup content

Rack number, Slot number

Relay address or register address


If you click [I/O Search] by the [PC Operation] menu, [I/O Search] dialog box will be displayed.

①

②

③

※

① Select assignment type

Select "Rack /Slot" or "Data Memory Address"

② Setup "Assignment"

When the assignment type is "Rack /Slot," setup "Rack No., Slot No.", and when the

assignment type is "Data Memory Address," setup "Relay Address" or "Register Address."

③ Click [Search]

⇒ Start I/O search

※ SU Light Off

As the result of I/O search, lighted SU lamp of the I/O module will be turned off when [SU Light Off]

is clicked.

5 ・63


[2] Secret

(JW10, JW30H, J-board(Z-511J/512J), VME Built-in Controller)

If you move the cursor to [Secret] of the [PC Operation] menu, [Secret] menu will be displayed.

(1) Function

Activate the register /change ,delete, secret ON of the password of the PC.

Item

Register/change Password

Delete Password

Secret ON

Content

Register the password that will be used as the secret function at the PC. Also, change the registered password.

Delete the password used at the secret function from the PC.

Validate the secret function of the PC.


①

②

③

① Register/change password

1. Click [Register/change Password]

⇒ "Password Setup" dialog box will be displayed.

2

3

2. Input password

Use alphabetical 4-digit number for "Register /Change."

However in case of using the handy programmer, use the area of "0 to 9" and "A to F."

3. Click [OK].

⇒ password will be changed /registered.

② Delete password

If you click [Delete Password] , the dialog box confirming the erase will be displayed. If you click

[OK] , the password will be erased.

③ Secret ON

If you click [Secret ON] , the dialog box confirming the secret ON will be displayed. If you click [OK] , the secret function will be validated.

5 ・64


When the PC is under the secret ON condition, you need to release the secret ON (secret OFF) to do processing with the PC. Input the registered password when the following dialog box asking to input the password for starting the communication with the PC is displayed.

If you input the password, the secret will be released, and it will remain under the secret OFF condition until it will be activated (secret ON).

Notes

・If you forget the password, you will not be able to communicate with the PC as a whole. Write down and keep the password somewhere safe.

[3] CU Memory Clear

(whole model)

(1) Function

Initialize (clear) the memory of the connected PC, and activate I/O register .

However, this function is valid when the PC is stopping.

Memory

Program Memory

Data Memory

System Memory

I/O register

Initialization Content

Clear

All 00

Initial value

On


If you click [CU Memory Clear], the dialog box confirming the clear operation will be displayed.

・ If you click [OK], the clear operation will be executed.

5 ・65


[4] Parity Check

(JW20/20H, J-board(Z-311J/312J/313J), JW50/70/100, JW50H/70H/100H, W100,

W70H/100H, W16/51)

(1) Function

Execute the parity check of the connected PC, and confirm "yes/no" of the error.


①

① Click [Parity Check]

⇒ The [Parity Check] dialog box will be displayed.

Display chart of the error address

②

② Click [Exec.]

⇒ The parity check will be executed (started).

・As the result of check, all the addresses in which errors occurred will be displayed.

5 ・66


[5] EEPROM

(JW20/20H, JW50/70/100, JW50H/70H/100H, JW30H, JW10, J-board,

VME Built-in Controller)

If you move the cursor to the [EEPROM] of the [PC Operation] menu, [EEPROM] menu will be displayed.

(1) Function

Activate the prepared EEPROM (in case of JW30H, flash ROM) and read/write to the connected PC.


①

②

① Read from EEPROM

1. Click [Read from EEPROM]

⇒ The confirmation dialog box for "reading" will be displayed.

2. Click [OK]

⇒ Start "reading" from EEPROM

② Write to EEPROM

1. Click [Write to EEPROM]

⇒ The confirmation dialog box for "writing" will be displayed.

2. Click [OK]

⇒ Start "writing" to EEPROM.

5 ・67


[6] I/O Table Automatic Registration

(JW20/20H, JW30H, J-board, VME Built-in Controller)

Read I/O register and registered I/O table information of the connected PC.

If you move the cursor to [I/O Table] of the [PC Operation] menu, [I/O Table] menu will be displayed.

(1) Function

Automatically register the I/O table of the connected PC.

(2) Operation

①

① Click [I/O Table Automatic Registration].

⇒ The dialog box confirming creation of the I/O table is displayed.

②

② Click [OK].

⇒ The I/O table is registered in the system memory of PC.

5 ・68


■

(Main/System/Data/Symbol/Parameter)

If you move the cursor to [PC Monitor] of the [PC] menu, [PC Monitor] menu will be displayed.

[1]

[2]

[3]

[1] Error Monitor

(1) Function

Monitor abnormal information of the connected PC.

・The monitor contents include: abnormal content, current condition, occurrence time, and the

number of occurred error.

・You can also clear the abnormal history that is stored in the PC.


①

① Click [Error Monitor]

⇒ [Error Monitor] dialog box will be displayed.

※

②

Item

Abnormal

Display content

Abnormal content

Status

Time

Times

Currently "abnormality occurring" or "recovered from abnormality."

The occurrence time of abnormality (displays the time of the very first occurrence if several abnormalities occur)

・The time is displayed correctly only when the correct time was setup in the

PC that contains the calendar clock.

The number of occurred error

※ If you click [Error Clear] , the abnormal history that is stored in the PC will be cleared.

② Click [OK]

⇒ The [Error Monitor] dialog box will close.

5 ・69


[2] Scan Time Monitor

(1) Function

Monitor the scan time of the connected PC.

・The monitor contents include: maximum value, minimum value, and current value.


①

① Click [Scan Time Monitor]

⇒ The [Scan Time] dialog box will be displayed.

②

② Click [OK]

⇒ The [Scan Time] dialog box will close.

5 ・70


[3] Clock Monitor

(1) Function

Monitor the internal clock to the connected PC.

・ display /setup the date and time.

・ You can not "clock monitor" in the PC model that does not carry the clock function.


①

① Click [Clock Monitor]

⇒ The [Clock Monitor] dialog box will be displayed, and you can monitor the date/time.

②

1. Click [Setup]

⇒ [Setup Clock] dialog box will be displayed.

2

1

※

3

2. Setup Date/Time

Place the cursor at the item you want to change, and input the value.

select the date.

・ ※If you click [Read from Computer], the date/time set in the computer will be input.

3. Click [Set]

⇒ The date/time set in the system memory of the PC will be written.

② Click [OK]

⇒ The [Clock Monitor] dialog box will close.

5 ・71


■

(JW50/70/100, JW50H/70H/100H, W70/100H)

(1) Function

Connect to the network module through the modem.

(2) Content

1

2

Note: Before connecting the modem, set up the modem by selecting [Setup]-[Communication

Setup]. (Refer to page 5-51)

1. Connection

Call the telephone number you set by selecting [Setup]-[Communication Setup].

After the connection, you can operate just like when connecting to the network.

・Once connected, the line continues to be connected without regard to operation of the

PC or monitor.

2. Disconnection

Disconnect the telephone line in communication.

5 ・72

Chapter 5 Menu Operation (Window)

5-8 Tool

(Main/Program/Symbol/Data/System/Parameter)

・Program:Ladder ・ Main/Program:Mnemonics/System/Data/Symbol/Parameter

■ Library

(Program:Ladder)

You can create the library, read the file, or save the file in the Library window.

Item

Read

Register

Display Content

If you click [Library]-[Read], the Library window will be displayed.

If you click [File]-[Read] in the Library window, the [Read Library

File] dialog box will be displayed. You can select and read the file in this dialog box.

You can read files of models you set in the Library window.

The expansion of readable files is the same with that of the LB2 library files.

If you click [Library]-[Register] after selecting lines to be registered in the Program:Ladder window, the Library windows will be displayed with the selected lines copied. If you click [File]

-[Save As] in this window, the [Register Library Files] dialog box will be displayed, and you can save file with an appropriate name.

For the detail of Library, refer to Chapter 6.

■ Multipoints Monitor


In the [Multipoints Monitor] window, you can monitor any data of data memory or system memory.

For the detail of multipoints monitor, refer to "Chapter 8 Monitor".

■ Sampling Trace


In the [Sampling Trace] window, you can see ON/OFF information of PC or contents of the register

by time charts. For the detail of sampling trace, refer to "Chapter 8 Monitor".

■ Option Parameter


In the [Option Parameter] window, you can set up parameters of models that save the parameters in the

option modules. For the detail of option parameter, refer to "Chapter 7 Setup Each Data".

5 ・73


■

(Program : Ladder)

This mode is used to transfer data between the system and a host computer (such as a CAD system).

First, the system converts programs and/or the symbol comments into character strings. Then it transfers them through an RS-232C interface or a floppy (hard) disk based on the settings of the communication parameters.

For details about the communication format, see the instruction manual for the CAD interface.

There are two methods to transmit data: through a communication port (RS-232C) and using a floppy

(hard) disk. On the [Program: Ladder] window, select [Tools] and [CAD I/F] from the menu bar, and the

[CAD I/F] dialog box will appear. Operate the data transfer with this dialog box.

(1) When you use the communication port

Select "Communication Port" on the "Transfer" item and specify "Communication setting" as the same as the settings in the CAD system.

The data transmission speed can be specified between 110 and 256,000 bps. However, you may not be able to select some speeds depending on the model of your personal computer. For details, see the instruction manual for the personal computer.

Select the RS-232C port for the communication port.

Specify each item of stop bit, parity, and data length appropriately.

(2) When you use a floppy (hard) disk

Select "File (FD, HD)" on the "Transfer" item. Enter a file name or click the "Reference" button to show the files currently available, and select one.

File extensions are as follows:

Ladder diagram with address: .awl

Ladder diagram: .lac

Symbol/comment (normal): .cmt

Symbol/comment (JW-50SP Ver.4.0): .c40

5 ・74


(3) Read/write a ladder program

Select either "Reading Ladder diagram" or "Writing Ladder diagram" on the "Process" item.

When you select "Reading Ladder diagram," the system will read the ladder diagram from a CAD system or a floppy (hard) disk. When you select the "Writing Ladder diagram," the system will write the ladder diagram to the CAD system or the floppy (hard) disk. When you want to read or write application instructions (specify numbers or symbols), specify without or with address, or if the memory volume of the program exceeds 39.0 K-bytes, select the file number 8 or 9 of the ladder diagram read/write, then click the [Run] button.

(4) Read/write a symbol/comment

Select either "Read Symbol/Comment" or "Write Symbol/Comment" on the "Process" item.

When you select the "Read Symbol/Comment," the system will read a symbol or comment from the

CAD system or the floppy (hard) disk. When you select the "Write Symbol/Comment," the system will write a symbol or comment to the CAD system or the floppy (hard) disk. Select either the normal format (symbol; one-byte 16 characters, comment; one-byte 28 characters) or JW-50SP Ver.4.0

format (symbol; one-byte six characters, comment; one-byte 24 characters) for the symbol/comment file format. Then click the [Run] button.

5 ・75


5-9 Window


If you click [Window] by the menu bar of each window, the [Window] menu will be displayed.

At the [Window] menu, you can operate the display method of several windows.

(Details in pages)

5-77

5-78

5-79

5-80

5-81

※ The above display is the case when the project name is "abc."

5 ・76


■ Open New Window


(1) Function

Open an another window that display the same content as the active window.

・ You can open several windows for a file, and you can also display parts of

the file to each window.

・ If you modify the content of the file in a window, all the windows that display the file will reflect

the change. However, in the program (ladder/mnemonic) window, the change will be

reflected after the modification.

(Refer to the page 6-46)

・ If you open the new window, the window becomes active, and it will be displayed in the front of

the screen.

(2) Operation Content

⇒

If you click [Open New Window], a new window that contains the same content of the displaying window will open.

・ A display example of the case

when operated by the

program (ladder/mnemonic)

・ A display example of the

case when operated by the

system.

・ A display example when the

window number exceeds

more than 10.

※ 1

※ 1

※ 2

※1 "1,2,3,…" after the window names suggests the order number of every opening window.

※2 If the opened windows exceed more than 10, click [More Windows], and select the window from the [Select Window] dialog box.

5 ・77


■ Overlap Display


(1) Function

Display several windows in a pile.


⇒

If you click [Overlap Display Arrange], several windows will be displayed in pile.

・The active window will be displayed in the front.

(Display example)

5 ・78

■


(1) Function

Display several windows in a row.



⇒

If you click [Display in Row], several windows will be displayed in a row.

(Display example)

5 ・79


■


(1) Function

Arrange icon at the below of the window.


⇒

If you click [Arrange Icons], the icons will be arranged.

(Display example)

・Iconized windows will be arranged at the bottom of the main window.

・If the basic window is open, and that this window is at the bottom of the main

window, you can not see the icon under this window.

5 ・80


(1) Function

Display the assigned window.

・The list of currently open basic window will be displayed at the below of the [Window] menu.

・A check mark will be displayed besides the name of currently active basic window.

The list of currently open basic window

Check mark


Click the window name [1,2,… ] of the [Window] menu.

⇒ The assigned window will be displayed.

・If more than 10 windows are open, [More Windows] will be displayed.

(Display example)

Click [More Windows], and select from

[Select Window] dialog box.

5 ・81

Chapter 5 Menu Operation (Help)

5-10 Help


If you click [Help] from the menu bar of each window, the [Help] menu will be displayed.

(1) Function

Display help on the assigned item by the table of “contents /keyword”.


⇒

If you click [Find Topic], [Find Topic] dialog box will be displayed.

● Display at the time of selecting “Contents”.

● Display at the time of selectin “Index”.

・If you keep clicking on the item to find, you can refer to the “help” of the related information, like operation order /reference.

・After referring to the help content, click [Contents] of the “help window” to go back to the first screen.

⇒

5 ・82

Chapter 5 Menu Operation (Help)

■

(1) Function

Display the version information of JW-100SP.


⇒

If you click [Version Data (MMVIEW)], the [Version Data (JW-100SP)] dialog box will be displayed.

Version display position

5 ・83

Chapter 6 Program Edit

Chapter 6 Program Edit (Ladder Programming)

There are two ways of creating a program: ladder and mnemonic.

Also, there are two ways to input a ladder program: direct input and dialog input.

Direct input

Dialog input

Program

Ladder program

Mnemonic program

6-1 Ladder Programming

When creating a new program, or when opening a program that is saved in a file, the

[Program : Ladder] window will be displayed.

Row address number Cell cursor Toolbar for ladder editing

Vertical scroll

Cell

Horizontal scroll

・The ladder display area is organized by the cell as the basic module.

・The group of cells that are lined perpendicularly is called the "column." The ladder display area is

organized from the 63rd columns, and use the horizontal scroll to display the column outside the

screen.

・The group of cells that are lined horizontally is called the "row." At the time of creating a new

program, there are 100 rows, the number of rows will increase by "Insert Row," [ ↓] key, or of

the vertical scroll bar. Use the vertical scroll to display the line outside the screen.

・Editing operation of the adder input or the modification requires the cell, column, and row as the

module.

6 ・1


Choose the display type of the ladder program from: Normal (Address) Display, Symbol Display,

Comment Display (8c. 4r), Comment Display (16c, 2r) or Full Display (Address/Symbol/Comment).

・Display the address (relay address or register address).

・In case the address was not assigned when creating a program by the symbol, "*****" will be

displayed at the address part.

Un-assigned address

Relay address

Register address

・Display the symbol (16 characters).

・In case the symbol was not registered when creating a program at the address, the symbol will

not be displayed.

Symbol

Symbol

Un-registered symbol

・Display the address (relay address or register address) and the comment (28 characters)

within four lines, each of which line can contain 8 characters.

・Comments are not shown if you do not register any comments.

・You cannot input, modify or delete the comments of application instruction, which is specific to

JW-100SP.

Un-assigned address

Relay address

Comment

Register address

Comment

Un-registered comment

Comment on application

instruction

6 ・2


・Display the address (relay address or register address) and the comment (28 characters) within

two lines, each of which can contain 16 characters.



JW-100SP.

Un-assigned address

Relay address

Comment

Register address

Comment



instruction

・Display the address (relay address or register address, etc), the symbol (16 characters) and the

comment (28 characters).

・If you have not assigned the address when creating the program with symbols, the address is

displayed as "*****".

・Symbols are not shown if you do not register any symbols.



JW-100SP.

Un-assigned address

Relay address

Comment

Register address

Symbol

Comment


Un-registered address


instruction

6 ・3


There are two types of input methods of the ladder program: direct input and dialog input.

To change between the input mode, use [Setup]-[Setup Input Type] of the menu bar. (For details on the setup input type, refer to the page 6-16)

【Input Mode】

Select either dialog input /direct input.

□ Inputs at Display Directry.

It becomes the direct input mode.

□ Inputs Using Dialog

It becomes the dialog input mode.

[1] Direct Input Mode

If the direct input mode is selected, it first initialize the value of relay address, register address, timer/counter address, and application instruction number, and then, it writes them directly to the selected cell position.

It is an useful mode especially when inputting, for example, the relay address after writing the part of ladder drawing first.

(1) Input instruction

・There are four input methods of instruction.

① Click the button of the toolbar for editing ladder. (basic instruction, application instruction)

② Select the [Instruction] menu command. (basic instruction, application instruction)

③ Push the key assigned in the [Key Assignment] (basic instruction, application instruction)

④ Select the instruction from the tree bar. (application instruction)

6 ・4


Input method of instruction and the initial value of instruction cursor at the time of the input

T o o l b a r

B u t t o n

I n s t r u c t i o n

M e n u

K e y a s s i g n e d d e f a u l t b y I n s t r u c t i o n

C u r s o r

I n i t i a l V a l u e

A c o n t a c t [ S ]

[ D ] B c o n t a c t

H o r i z o n t a l il n e

V e r t i c a l il n e

[ F ]

[ G ]

O U T

T M R

[ X ]

[ V ]

C N T [ C ]

F U N [ B ]

F 4 3

F 4 4

[ H ]

[ J ]

F 4 5 [ K ]

(1)-1 The input order by the toolbar button.

1. Select the instruction of the toolbar by the mouse cursor. In case the mouse cursor is the arrow

-shaped cursor, it changes to the instruction cursor (described above).

2. Move the instruction cursor to where you input the instruction, and click it to input the

instruction. However, the address, application instruction number become the initial value

(described above).

・When the display type is "Symbol Display"/"Full Display (Address/Symbol/Comment)," the symbol will be displayed only if the address of initial value of the symbol has been "symbol registered."

・When the display type is Comment(8c, 4l)/Comment(16c, 2l)/Full(Address/Symbol/

Comment), the comment will be displayed only if the address of initial value of comment has been "comment registered."

3. Only if the instruction cursor is , , , , you can input the instruction

continuously by dragging it on the screen.

4. To change the instruction cursor to the arrow-shaped cursor, click the right side of the mouse or

use the [ESC] key, or button.

(1)-2 Input order by the [Instruction] menu

1. When the mouse cursor is the arrow-shaped cursor, move the cell cursor to the position where

you input the instruction.

If the mouse cursor is the instruction cursor, change the instruction cursor to the arrow-

shaped cursor by clicking the right side of the mouse or use the [ESC] key, or button.

2. If you click the instruction of the [Instruction] menu, the instruction will be input. However,

the address, application instruction number become the initial value (described above).

The display of the symbols and comments is the same with the item 2 of (1)-1 above.

6 ・5


(1) -3 Input order by the Assigned key

1. When the mouse cursor is the arrow-shaped cursor, move the cell cursor to the position where

you input the instruction.If the mouse cursor is the instruction cursor, change the instruction

cursor to the arrow-shaped cursor by clicking the right side of the mouse or use the [ESC] key,

or button.

2. If you press the assigned key, the instruction will be input. However, the address, application

instruction number become the initial value (see the previous page). The display of the symbols and

comments is the same with the item 2 of (1)-1 above.

(1) -4 Input order of the application instruction by the tree bar

1 ．

" ＋" of the tree, or double click the instruction, the instruction at the lower layer will be displayed.

2 ．＋" until the inputting instruction will be displayed at the tree bar.

3 ．

instruction cursor ( ) will be displayed.

4 ．

instruction. However, the address and the constant number become the initial value (relay:

00000, register: ]0000, constant:0). The display of the symbols and comments is the same with

the item 2 of (1)-1 above.

Initial value

(1)-5 Input order of the F-20 (MD) instruction

1. When the mouse cursor is the arrow-shaped cursor, move the cell cursor to the position where you input the instruction.If the mouse cursor is the instruction cursor, change the instruction cursor to the arrow-shaped cursor by clicking the right side of the mouse or use the [ESC] key, or button.

2. If you click F-20 (MD) instruction of the

[Instruction] menu or press the function key ([Shift]+[F8]), [Input F-20 (Maintenance Display)] dialog box will be displayed.

3. Here, you setup the number of input lines, MD number and MD data, and click [OK] button to input the instruction.

6 ・6


(2) Input Address

・When inputting the instruction by the direct input mode, the relay address, register address,

application instruction number, etc. will be setup at the initial value so that you need to modify

them with the correct value.

・To change from the instruction input mode to the address input mode, select the instruction cell

by the arrow-shaped cursor, and use "double click" or the [Enter] key. "Double click" by the

mouse is only valid when the "Becomes address input" at the setup of [Double Click] of the

[Setup Input Type] dialog box is selected.

(Instruction input mode) (Address input mode)

●

・When the display type is Normal(address)/Comment(8c, 4l)/Comment(16c, 2l)/

Full(Address/Symbol/Comment). (Refer to page 6-2)

In case the display type is Comment(8c, 4l)/Comment(16c, 2l)/Full(Address/Symbol/

Comment), the input dialog box is shown to input the address. You can also input the symbol

and the comment in that dialog box.

Comment(8c, 4l)/Comment(16c, 2l) Full(Address/Symbol/Comment)

・Input the address in the numerical value key. You can omit "0’s" of the high digit number.

(Example of address input)

K i n d

R e l a y A d d r e s s

T i m e r ・ C o u n t e r N u m b e r

T i m e r ・ C o u n t e r

V a l u e

S e t u p

A p p il c a t i o n

N u m b e r


R e g i s t e r A d d r e s s

A p p

C il c a o n s t i t a n t o n I n s t r u c t i o n

N u m b e r

E x a m p l e

0 0 0 0 1

0 0 0 1

[ 1 ] [ E n t e r ]

[ 1 ] [ E n t e r ]

F

0 0 0 1

F 0 0 0

] c b

0

0 0

0

1

0 0

0

2

0 1

1 w

0 1

0 9 0 0 1

E 0 0 0 1

@ 9 9 0 0 0

[ 1 ] [ E n t e r ]

I n p u t

[ F ] [ 0 ] [ E n t e r ] o r [ 0 ] [ E n t e r ]

[ F ] o r

[ C ]

[ C ]

[ 1 ]

[ 1 ]

[ 2 ]

[ 2 ]

[ W ]

[ W ]

[ E n t e r ]

[ E n t e r ]

[ ] ] [ 1 ] [ E n t e r ]

[ B ] [ 1 ] [ E n t e r ]

[ 0 ] [ 9 ] [ 1 ] [ E n t e r ]

[ E ] [ 1 ] [ E n t e r ]

[ @ ] [ 9 ] [ 9 ] [ 0 ] [ E n t e r ]

[ 1 ] [ E n t e r ]

・There are no differences between upper and lower cases of [F], [C], [X], [W], [D], [B], [E].

Depends on the kind of application instruction, there is a case when the dialog box is

displayed instead of inputting the address directly. (the 3rd word of JW30H F-85, etc.)

・Select the cell in which the register is displayed, and if you input the [F1] key, the register area

will change in the following order.

]0000 → b0000 → 09000 → 19000 → ････ → 99000→E0000

6 ・7


・When the display type is Symbol/Full(Address/Symbol/Comment). (Refer to the page 6-2)

・Input the symbol within 16 characters.

・There are two methods of creating a program by the symbol input.

① Create a program using the symbol that has already been registered at the [Symbol]

window.

② After creating a program by using the un-registered symbol, assign the address at the

[Assign Symbol] window .

6 ・8


[2] Dialog Input Mode

If an instruction is selected, the dialog input mode display the dialog box where the relay address and the register address are input.

In this mode, you can change between address /symbol input, change between application instruction indirect /direct register, and the setup of the register area setup at the dialog box, according to the each instruction.

(1) Input Instruction

・There are four types of instruction input methods.

① Click the button of the toolbar for editing ladder. (basic instruction, application instruction)

② Select the [Instruction] menu command. (basic instruction, application instruction)

③ Push the key assigned in the [Key Assignment] (basic instruction, application instruction)

④ Select the instruction from the tree bar. (application instruction)

(1) -----1 Input order of the basic instruction (A contact, B contact, OUT)

1. Move the cell cursor to the position where you input the instruction.

2. Select the instruction (A contact, B contact, OUT) from the toolbar for editing ladder,

[Instruction] menu, and the assigned key.

3. Select the input type (relay address /symbol input) by the mouse when the dialog box is

displayed.

[A contact] dialog box [B contact] dialog box

[OUT] dialog box

4. Input address or symbol

“0’ of the high digit

number.

・When inputting TMR /CNT contact, press button. In case of TMR contact, click

[T0000], and in case of CNT contact, click [C0000], and finally input the address.




window.



5. If you click [OK] button, the instruction will be input.

6 ・9


(1)- 2 Input order of basic instruction (horizontal line, vertical line)

1. Move the cell cursor to the position where you input the instruction (horizontal line, vertical

line).

2. If you select instruction (horizontal line vertical line) from the toolbar for editing ladder, the

[Instruction] menu and the assigned key, horizontal line /vertical line will be input.

(1) - 3 Input order of basic instruction (TMR, CNT)


2. Select the instruction (TMR, CNT) from the toolbar for editing ladder, the [Instruction] menu

and the assigned key.

3. When the dialog box is displayed, select by mouse the TMR type, the numerical value type and

the input type (TMR No./Symbol) for TMR instruction, and select by mouse the CNT type, the

numerical value type and the input type (CNT No./Symbol) for CNT instruction.

[TMR Instruction] dialog box

[CNT Instruction] dialog box

4. Input the address (TMR No./CNT No.) or symbol.

・Input the address by the numerical value key. You can omit "0’s" of the high digit

number.




window.

② After creating a program by using the un-registered symbol, assign the address at

the [Assign Symbol] window .

5. Input the setup value by the numerical value key.


6 ・10


(1)- 4 Input order of application instruction 1 (In case of selecting the instruction at the

dialog)


2. Select instruction (FUN) from the toolbar for editing ladder, the [Instruction] menu and the

assigned key.

3. When the [Select Application Instruction] dialog box is displayed, select the instruction to input

in the "General classification", "Detail classification" and "Instruction" by double clicking the

mouse in order.

([Select Application Instruction] dialog box)

4. If the instruction is displayed at the part of the "Inputs instruction," click [OK] button.

5. The dialog box of each instruction will be displayed, and select the input type (Address /

Symbol) by the mouse for the instruction that has the "setup register / relay." Also, if you want to assign the address to the register indirectly, you can check it with the mouse.

6. For the instruction that has the "setup register /relay," input the address or symbol.

・In case of "setup register," press button, and display the register area, and finally

select the area that contains the register to setup.


number.




window.


[Assign Symbol] window.

6 ・11


7 ．

value key.

8 ．

(1)-5 Input order of application instruction 2 (In case of selecting the instruction by the tree

bar.)

1. Move the cursor to the position where you input the instruction.

2. At the tree bar, the application instruction is classified according to the function. If you click "+" of the tree, or double click the instruction, the instruction at the lower layer will be displayed.

3. Click "+" until the inputting instruction will be displayed at the tree bar.

4. If you click the inputting instruction, the dialog box of each instruction will be displayed, and select the input type (Address /Symbol) by the mouse for the instruction that has the "setup register /relay." Also, if you want to assign the address to the register indirectly, you can check it with the mouse.

5. For the instruction that has the "setup register /relay," input the address or symbol.

・In case of "setup register," press button, and display the register area, and finally

select the area that contains the register to setup.


number.

6 ・12





window.

② After creating a program by using the un-registered symbol, assign the address at

the [Assign Symbol] window.

6. For the instruction that has been setup with the constant, input the constant

by the numerical value key.


(1)-6 Input order of F-43 (bit reverse), F-44 (ON differential), F-45 (OFF differential)

instruction

1. Move the cursor to the position where you input the instruction.

2. if you select each instruction from the toolbar for editing ladder, the [Instruction] menu and the

assigned key, the instruction will be input.

(1)-7 Input order of F-20 (MD) instruction


2. If you click F-20 (MD) instruction of the [Instruction] menu or press the function key ([Shift]+

[F8]), [Input F-20 (Maintenance Display)] dialog box will be displayed.

3. Setup the number of input lines, MD number and MD data.

4. Click [OK] button to input the instruction.

6 ・13


(2) Input Address

・When inputting the instruction in the dialog input mode, you normally input the relay address,

register address, application instruction number, etc. at the dialog box, but in case you want to

modify the once setup address, change the instruction input mode to the address input mode.

(Instruction input mode) (Address input mode)

・ To change from the instruction input mode to the address input mode, select the instruction cell

by the arrow-shaped cursor, and use "double click" or the [Enter] key. "Double click" by the

mouse is only valid when the "Becomes address input" at the setup of [Double Click] of the

[Setup Input Type] dialog box is selected.

・When the display type is Normal(address)/Comment(8c, 4l)/Comment(16c, 2l)/

Full(Address/Symbol/Comment). (Refer to page 6-2)

In case the display type is Comment(8c, 4l)/Comment(16c, 2l)/Full(Address/Symbol/

Comment), the input dialog box is shown to input the address. You can also input the symbol

and the comment in that dialog box.

Comment(8c, 4l)/Comment(16c, 2l) Full(Address/Symbol/Comment)

・Input the address in the numerical value key. You can omit "0’s" of the high digit number.

(Example of address input)

K i n d




V a l u e

S e t u p

E x a m p l e

0 0 0 0 1

0 0 0 1

0 0 0 1

[ 1 ] [ E n t e r ]

[ 1 ] [ E n t e r ]

[ 1 ] [ E n t e r ]

I n p u t


N u m b e r



F 0 0 0

F c 0 1 2 w

] 0 0 0 1 b 0 0 0 1

0 9 0 0 1

E 0 0 0 1

@ 9 9 0 0 0

[ F ] [ 0 ] [ E n t e r ] o r [ 0 ] [ E n t e r ]

[ F ] o r

[ C ]

[ C ]

[ 1 ]

[ 1 ]

[ 2 ]

[ 2 ]

[ W ]

[ W ]

[ E n t e r ]

[ E n t e r ]

[ ] ] [ 1 ] [ E n t e r ]

[ B ] [ 1 ] [ E n t e r ]

[ 0 ] [ 9 ] [ 1 ] [ E n t e r ]

[ E ] [ 1 ] [ E n t e r ]

[ @ ] [ 9 ] [ 9 ] [ 0 ] [ E n t e r ]

A p p il c a t i o n I n s t r u c t i o n

C o n s t a n t N u m b e r

0 0 1 [ 1 ] [ E n t e r ]

・ There are no differences between upper and lower cases of [F], [C], [X], [W], [D], [B], [E].

Depends on the kind of application instruction, there is a case when the dialog box is

displayed instead of inputting the address directly. (the 3rd word of JW30H F-85, etc.)

・ Select the cell in which the register is displayed, and if you input the [F1] key, the register

area will change in the following order.

]0000 → b0000 → 09000 → 19000 → ････ → 99000→E0000

6 ・14


・When the display type is Symbol/Full (Address/Symbol/Comment). (Refer to the page 6-2)



① Create a program using the symbol that has already been registered at the [Symbol] window.



6 ・15


Click [Setup]-[Setup Input Type] of the menu bar, and display the [Setup Input Type] dialog box.

Select either dialog input /direct input

□ Inputs at Display Directry

It becomes the direct input mode.

□ Inputs Using Dialog

It becomes the dialog input mode.

□ Do

If you input the address during the address input mode and press the [Enter] key, you can

input the address of the cell which is found just on the right side. (In case there is no cell on the

right side for the address input, move to the valid cell for the address input.)

In this case, you can change the instruction input mode by moving the cursor to the different

cell, or by selecting the [ESC] key.

□ Undo

If you input the address during the address input mode and press the [Enter] key, you can

change to the instruction input mode.

□ Becomes Address Input

If you double click the mouse on the cell which accepts the address input, the instruction input mode changes to the address input mode.

□ Changes Instruction at Cell

・If you double click the mouse on the cell displaying the basic instruction (A contact, B

contact,horizontal line, coil), the display will change to the following in order.

A contact →B contact→horizontal line→coil

The relay number does not change, however.

・ If you double click the mouse on the cell displaying the number of timer, counter instruction,

the display will change to the following in order. (The change differs according to the PC

model.)

TMR→DTMR (BCD)→DTMR (BIN) →UTMR (BCD) →UTMR (BIN)

CNT→DCNT (BCD)→DCNT (BIN) →UCNT (BCD) →UCNT (BIN)

The timer number and the counter number do not change, however.

6 ・16


・If you double click the mouse on the cell displaying the application instruction number, the display will change to the following in order. (The change differs according to the PC model.)

F-XXX →F-XXXw→F-XXXd→FcXXX→FxXXX→FcXXXw→FxXXXw

The application instruction number does not change, however.

・In the direct input mode, if you double click the mouse on the cell which is not displaying anything , the display will change to the following in order.

A contact →B contact→horizontal line→coil

・In the dialog input mode, you can not double click the mouse on the cell which is not displaying anything.

・If you double the mouse on the vertical line input position, a vertical line will be input.

Setup the button movement of the toolbar for editing ladder by the application instruction (F-

60,F-61,F-62, etc.) waiting for the several inputs or by CNT instruction.

You can not narrow the instruction frame in the dialog input mode.

□ Process with Row Data a) In case of direct input mode

If you click the button, the mouse cursor changes to the enlarge/contract cursor. If you drag the enlarge/contract cursor to the instruction frame area of the line where you want to widen, the instruction will be widened /narrowed in vertical direction. At the same time, the line of input contact will move.

b) In case of dialog input mode

If you click the button when there is the cell cursor in the instruction frame of the line where you want to widen, the instruction will be widened in vertical direction. At the same time, the line of input contact will move.

□ Process Application Instruction Only a) In case of direct input mode

If you click the button, the mouse cursor changes to the enlarge/contract cursor. If you drag the enlarge/contract cursor to the instruction frame area of the line where you want to widen, the instruction will be widened /narrowed in vertical direction. The line of input contact will not move.

b) In case of dialog input mode

If you click the A button when there is the cell cursor in the instruction frame of the line where you want to enlarge, the instruction will be enlarged in vertical direction. The line of input contact will not move.

6 ・17


[1] Over Write /Insert Mode

It's the mode when the another element was written over on the cell where the instruction (element) such as A or B contact exist already. The movement is the same on the cell where the element is not written.

Over write mode : Write over with a new element. (refer to the next paragraph)

Insert mode : Insert the new element. There are two types of inserts : insert left and

insert right. (refer to the page 6-20)

There are tow types of changing methods of over write/insert mode

① Double click the [Over write]/[Insert] display part of the status bar.

② Press the [Insert] key.

Over write mode Insert mode

[2] Modify Circuit

The editing method inside the circuit (1 network) is explained.

(1) Modify instruction (over write and modify)

・You can change the circuit by writing over another instruction on the cell in which an instruction

has been already written.

・Execute over write mode (refer to the previous paragraph)

(Example 1)

Modify the A contact to the horizontal line → delete A contact

(Example 2)

Modify TMR instruction to the CNT instruction

・Since the CNT instruction uses 2 lines, the line below the CNT instruction will all move down

one line.

・After this, write the second input (reset input) of CNT instruction.

・In the direct input mode, CNT number and "setup value" become the initial values, so that you

need to modify them after the instruction input.

6 ・18


(Example 3) Modify the Fc210 (ADD) instruction to F-63 (INC) instruction

・In the direct input mode, the application instruction number, the register number and the constant become the initial values, so that you need to modify them after the instruction input.

(2) Delete instruction 1 ( button : eraser, or use the [Delete] key)

・ button (eraser) is used to delete the instruction by the cell module.

・It is useful for deleting the vertical line (OR line), etc.

Delete vertical line

(OR line)

1. If you click button, the cursor changes to the [Eraser] cursor.

2. If you click on the instruction that is to be deleted (the vertical line in the display above), the instruction will be deleted.

1. Move the cell cursor to the deleting cell.

2. If you click button, the instruction will be deleted. If the cell which is to be deleted contains the vertical line (OR line) (in case of the example above), the [Delete instruction] dialog box will be displayed.

3. In case you are deleting only the vertical line (OR line), select "OR Line," and [OK] button.

Then the vertical line (OR line) will be deleted.

・The instruction at the cell cursor position will also be deleted with the [Delete] key.

6 ・19


(3) Delete instruction 2 (use the [Delete Cell] command)

・If you use the [Delete Cell] command, you can delete several cells in the horizontal direction

(column direction) in batch.

・The area where you have deleted the cells becomes blank.

2 ．

・In case of canceling the deletion, click [Edit]-[Undo] of the menu bar.

・In the insert mode (refer to the page 6-18), you can inset another element on the cell where the instruction (element) such as A or B contact exist already.

Insert mode

・There are two types of inserts: insert left and insert right.

In the direct input mode, if you click the instruction cursor (A contact, B contact, horizontal line, F-

43, F-44, F-45) on the inserting cell , the new element will be inserted in this cell.

In the dialog input mode, if you click the instruction cursor (A contact, B contact, horizontal line, F-

43, F-44, F-45) on the inserting cell , the new element will be inserted in this cell.

insert

In the direct input mode, if you click the instruction cursor (A contact, B contact, horizontal line, F-

43, F-44, F-45) by keep pressing the [Shift] key on the inserting cell , the new element will be inserted on the right side of the cell.

Insert

In the dialog input mode, you can not inset on the right.

6 ・20


(5) Insert instruction 2 (use [Insert Cell] command)

・If you use the [Insert Cell] command, you can delete several cells in the horizontal direction

(column direction) in batch.

・The cells on the right of the inserted position move right in the number of inserted cell columns.

1. Move the cell cursor to the cell where you insert the instruction.

2. If you are inserting several cells, simply drag them.

3. If you click [Edit]-[Insert Cell] of the menu bar, an empty cell will be inserted.

4. Write the inserting instruction to the inserted cell position.

(6) Insert instruction 3 (use the [Insert Row] command)

・If you use the [Insert Row] command, you can insert several rows in batch.

・It is useful for inserting the OR instruction.

・All lines below the inserted line will move down the same number of rows inserted.

1. Move the cell cursor to the line where you insert the instruction.

2. If you are inserting several cells, simply drag them.

3. If you click [Edit]-[Insert Row] of the menu bar, an empty line will be inserted.

4. Write the inserting instruction to the inserted cell position.

6 ・21


[3] Delete Circuit

Use the [Delete Row] command when you are deleting by the circuit (network) module.

2 ．

・In case of canceling the deletion, click [Edit]-[Undo] of the menu bar.

[4] Insert Circuit

Use [Insert Row] command when inserting the circuit (network) .

1. Drag only the amount of rows of the inserting circuit from the row number of the insert

position.

2. If you click [Edit]-[Insert Row] of the menu bar, empty lines will be inserted.

3. Write the circuit to the inserted row.

6 ・22


[5] Copy Circuit

Use [Copy], [Paste] command when copying the circuit (network).

1. Drag the line number of the circuit which is to be copied.

2. If you click [Edit]-[Copy] of the menu bar, the circuit which is to be copied will be momentarily

saved.

3. Click the row number of the destination of the copy.

4. If you click [Edit]-[Paste] of the menu bar, the "copy circuit" will be completed.

6 ・23


[6] Move Circuit

Use [Insert Row], [Cut], [Paste], [Delete Row] commands when moving the circuit (network).

1. Drag only the amount of lines of the moving circuit from the line number of the moving

destination.

2. If you click [Edit]-[Insert Row] of the menu bar, and empty line will be inserted.

3. Drag the row number of the moving circuit.

6 ・24


4. If you click [Edit]-[Cut] of the menu bar, the moving circuit will be deleted, and it will be momentarily saved.

5. Click the row number of the moving destination.

6. If you click [Edit]-[Paste] of the menu bar, the circuit which was cut at No.4.will be pasted.

7. After dragging the empty row (the circuit line before the moving : 000002,000003) which has already been moved, if you click [Edit]-[Delete Row] of the menu bar, the empty row will be deleted, and the moving will be completed.

When changing ladder to mnemonic, however, the empty row will be ignored, so that it will not affect the calculations at the PC even though you don't execute this operation.

6 ・25


By registering the created programs in the library file, you can create a similar ladder circuit easily.

[1] Register to Library

Register the circuit created at the [Program : Ladder] window to the library file.

1. Select by dragging the line number of the circuit which is to be registered.

2. Click [Tool]-[Library]-[Register] of the menu bar.

⇒The [Register library] window will be opened, and the circuit selected at No.1. will be

displayed.

Menu Bar

Main Toolbar

Toolbar for

Editing Ladder

Ladder Display

Area

Increase/

Decrease

Value

Message Bar

Status Bar

6 ・26


M e n u C o m m a n d

R e a d

F li e

S a v e A s

S a v e

Q u i t

U n d o

C u t

C o p y

P a s t e

I n s e r t C e ll

E d i t

I n s e r t R o w

D e l e t e C e ll

D e l e t e R o w

C r e a t e L i n e C o m m e n t

F i n d

J u m p [ T o T o p R o w ]

J u m p

[ T o U n e d i t e d R o w ]

J u m p

[ T o A s s i g n e d R o w ]

J u m p

[ T o A d d r e s s M a r k ]

A c o n t a c t

B c o n t a c t

H o r i z o n t a l L i n e

V e r t i c a l L i n e

O U T


T M R

C N T

F U N

U s e d a f li e .

a t t h e [ R e a d f r o m

S a v e w i t h a n e w n a m e .

U s e d a t t h e [ R e a d f r o m

Q u i t t h e il b r a r y r e g i s t e r o r t h e r e a d i n g .

C a n c e l t h e o p e r a t i o n t h a t h a s

C o n t e n t

C u t t h e s e l e c t e d a r e a a n d s a v e s i t m o m e n t a r li y .

C o p y t h e s e l e c t e d a r e a a n d s a v e s i t m o m e n t a r li y .

P a s t e t h e c u t o r c o p i e d d a t a t o

I n s e r t t h e c e ll t o t h e a s s i g n e d a r e a .

I n s e r t t h e R o w t o t h e a s s i g n e d a r e a .

D e l e t e t h e c e ll t o t h e a s s i g n e d a r e a .

D e l e t e t h e R o w t o t h e a s s i g n e d a r e

I n s e r t t h e c o m m e n t t o t h e a s s i g n e d

F i n d a f t e r a s s i g n i n g a d d r e s s ( r e l a y ,

M o v e t h e

M

M o o v v e e

M o v e

U s e d t t h h e e t h e w h c u r s o r t o t h e c u r s c u r s o r o r c u r s o r e n i n p u t t t o o t o t i t t t n g

U s e d w h e n i n p u t t i n g

U s e d w h e n i n p u t t i n g h h e e h e

A f r o n t r o w .

u a il b r a r y ] w i n d o w .

R e a d t h e s a v e d w h i c h h a s a l r e a d y b e e n s a v e d i n il b r a r y ] w i n d o w .

S a v e w i t h t h e c u r r e n t f li e n a m e .

n e s s a d d c o n i d i t g n j u s t b e e n e x e c u t e d .

e d e d r e s s t a c t

B c o n t a c t

U s e d w h e n i n p u t t i n g h o r i z o n t a l

U s e d w h e n i n p u t t i n g v e r t i c a l t h e c u r s o r p o s i t i o n .

r r m o w o a w r il n e .

il n e .

r e g i k

.

il n e .

( e t h s t e r ) m p t y a t h

U s e d w h e n i n p u t t i n g O U T i n s t r u c t i o n ( c o li ) .

U s e d w h e n i n p u t t i n g T M R i n s t r u c t i o n .

U s e d w h e n i n p u t t i n g C N T i n s t r u c t i o n .

a p p il c a t i o n i n s t r u c t i o n .

a r s

, m n e m o n i c o w b

) e

.

e n s e t u

, c h p .

a r a c t e r il n e ( s y m b o l ) .

I n

V i s e e r w t

S e t u p

F 4 3

F 4 4

U s e d w h e n i n p u t t i n g F 4 3 i n s t r u c t i o n ( b i t r e v e r s e ) .

U s e d w h e n i n p u t t i n g F 4 4 i n s t r u c t i o n ( O N d i f f e r e n t i a l ) .

F 4 5

F 2 0 ( M D )

U

U s s e e d d w w h h e e n n i i n n p p u u t t t t i i n n g g

F

F

-

-

4

2

3

0 i i n s n s t r u c t r u c t i o n t i o n

(

(

O

M

F

D

F

) .

d i f f e r e n t i a l ) .

I n

A ll s e

C r l t

C o n v e r t s

B a t c h e a r

V a r i a t i o n I n

A r r a n g e L a d d e r D i a g r a m

M a i n T o o l b a r

U s e d a t t h e [ R e a d f r o m il b r a r y ] .

R e a d t h e il b r a r y c i r c u i t t o t h e [ P r o g r a m : L a d d e r ] w i n d o w .

C h a n g e v a l u e .

i n b a t c h t h e " i n c r e a s e / d e c r e a s e " v a l u e u s e d a t t h e r e p e a t i n g , t o t h e o p t i o n a l

E r a s e l a d d e r d i s p l a y a r e a .

A d j u s t o u t p u t i t h e n s t r c o n n u c t i o e c n t i o n a n d o f t h

M C S e

/ J d i s c o n n e c t e d

C S c o n d i t i o n c i r c u i t , d i s p l a y .

t h e d i s p l a y p o s i t i o n a d j u s t m e n t o f t h e

S e l e c t " Y e s / N o " o f t h e m a i n t o o l b a r d i s p l a y .

S t a t u s B a r

M e s s a g e B a r

T o o l b a r f o r E d i t i n g L a d d e r

S e l e c t " Y e s / N o " o f t h e s t a t u s b a r d i s p l a y .

S e l e c t " Y e s / N o " o f t h e m e s s a g e b a r d i s p l a y .

S e l e c t " Y e s / N o " o f t h e t o o l b a r f o r e d i t i n g l a d d e r d i s p l a y .

S

S

K e e e t t y u u p p

A

I n p

D s s i s u t p l i g n

T y a y p e

P m e n t a t t e r n t

S h e t e u p t h

[ P r o e g r i n p u t a m : m o d e

L a d d e r ]

( d i w i r e n c t d o i n p w , u t s o

/ d i f o a l r o g m o r i n e p u t ) d e t a e t c li s ,

.

.

.

, o f r e f e r t h e t o t l a d h e d p e r a g

.

e

I t ' s s 6 t h e

4 t o s a m e

1 7 .

s e t u p a s

A d j u s t t h e d i s p l a y p o s i t i o n o f c o li , T M R / C N T i n s t r u c t i o n , a p p il c a t i o n i n s t r u c t i o n .

A s s i g n t h e k e y s t o i n p u t l a d d e r i n s t r u c t i o n s .

C h a n g e T a r g e t M o d e l D e f i n e t h e m o d e l t o c r e a t e o r e d i t t h e p r o g r a m f o r .

H e l p

V e r s i o n

L i b r a r y

I n f o r m a t i o n o f

S h o w t h e v e r s i o n o f t h e il b r a r y .

6 ・27


diagram

Information

Same as [File]-[Read]

Same as [File]-[Save]

Same as [Insert]-[Insert]

Same as [Edit]-[Cut]

Same as [Edit]-[Copy]

Same as [Edit]-[Paste]

Same as [Edit]-[Undo]

Same as [Edit]-[Find]

Same as [Display]-

[Arrange Ladder Diagram]

Same as [Help] -

[Version Information of Library]

(Refer to the

previous page)

Same as the function of the toolbar for editing ladder of the [Program : Ladder] window.

Refer to the page 3-8.

Display the work completed message or the error message.

Display the input mode and the overwrite/insertion mode.

6 ・28


(1) Edit ladder circuit

At the [Register Library] window, you can edit the ladder circuit in the same way as the [Program :

Ladder] window, but there are following exceptions.

I n p u t S y m b o l / C o m m e n t

[ P r o g r a m : L a d d e r ] w i n d o w

P o s s i b l e

P o s s i b l e

P o s s i b l e

[ R e g i s t e r L i b r a r y ] w i n d o w

( o n l y

I m p o s s i b l e a d d r e s s i n p u t )

I m p o s s i b l e

( o n l y a d d r e s s d i s p l a y )

I m p o s s i b l e

[ R e a d L i b r a r y ] w i n d o w

I m p o s s i b l e

( o n l y a d d r e s s i n p u t )

I m p o s s i b l e

( o n l y a d d r e s s d i s p l a y )

I m p o s s i b l e

D i s p l a y S y m b o l / C o m m e n t

I n p u t A p p il c a t i o n b y t h e T r e e B a r


F i n d C o n t i n u o u s l y

F i n d C o li

Z o o m

P r o g r a m C h e c k

C o n v e r t D a t a i n B a t c h

S e t u p

V a l u e

I n c r e a s e / D e c r e a s e

S e l e c t P C M o d e l

C h a n g e t o

M n e m o n i c / M n e m o n i c D i s p l a y

P o s s i b l e

P o s s i b l e

P o s s i b l e

P o s s i b l e

P o s s i b l e

I m p o s s i b l e

P o s s i b l e

P o s s i b l e

I m p o s s i b l e

I m p o s s i b l e

I m p o s s i b l e

I m p o s s i b l e

I m p o s s i b l e

P o s s i b l e

I m p o s s i b l e

[

( b e c o

P r o g r m a : e s t h e m o d m L a d d e r ] e l w o i n f t h e d o w )

I m p o s s i b l e

I m p o s s i b l e

I m p o s s i b l e

I m p o s s i b l e

I m p o s s i b l e

I m p o s s i b l e

P o s s i b l e

( T h e

1 0 0 S P

P o s s i b l e m o d b e c o e l m s t a r t e d e s t h e b y o n e

J W o f t

h e

[ P r o g r a m : L a d d e r ] w i n d o w )

I m p o s s i b l e

If you click [Insert]-[All Clear] of the menu bar, you can erase the whole ladder circuits of the

[Register Library] window.

(2) Setup increase /decrease value

You can read continuously (assigned times) the ladder circuit that was registered in the library, in

the [Program : Ladder] window. In this case, you can only read the assigned increase /

decrease value by increasing /decreasing the relay address or the register address.

(Example)

Repeat 5 times

6 ・29


Depends of the setup of [Double Click] of [Setup]-[Setup Input Type] of the menu bar, the modifying method of increase /decrease value becomes different.

・In case of setting up "Becomes address input."

If you double click the arrow-shaped cursor at the increase /decrease value position, the increase /decrease value input mode will be set.

・In case of setting up "Changes instruction at cell."

If you press [ ↓] key after pressing the [Enter] key, the increase /decrease value input mode will be set.

(Instruction input mode) (Increase /decrease value input mode)

The initial value of the increase /decrease value is 0, and the input area is -7777 to +7777 (octal notation). "+" can be omitted.

You can change the increase /decrease value of the ladder circuit of the active [Register Library] window in batch to the same value .

If you click [Insert]-[Converts Variation in Batch] of the menu bar, [Change Increase /Decrease

Value in Batch] dialog box will be displayed.

If you click [OK] button after checking the "Change to Manual Value" first, and then, inputting the increase /decrease value, "change in batch" will be executed.

If you click [OK] button after checking "Clear All", all the increase /decrease value will be 0.

(3) Save library file

If you click [File]-[Save As] of the menu bar, the [Register library file] dialog box will be displayed.

If you click [Save] button after setting up the place (directory) to save first, and then inputting the file name, it will be saved in a file. (file of the extension lb2)

Also, the line comment file is also created at the same time. (file of the extension lbc)

6 ・30


[2] Read from Library

Read out the ladder circuit that was registered at the library to the [Program : Ladder] window.

1. Move the cell cursor to the position where you are reading out the circuit that has been registered at the library.

2. Click [Tool]-[Library]-[Read] of the menu bar.

⇒ The [Read from Library] window will be opened. At this time, the ladder display area is being cleared.

Menu Bar

Main Toolbar

Toolbar for

Editing Ladder

Ladder Display

Area

Message Bar

Status Bar

For explanations on the menu bar, main toolbar, toolbar for editing ladder, message bar, status bar, refer to the pages 6-27 to 28.

6 ・31


3. Click [File]-[Read] of the menu bar when reading out the library file that has already been saved.

⇒ [Read from library file] dialog box will be displayed.

4. Select the reading file name, and click [Open] button. Only file that you can read is the file with the

extension lb2.

⇒ The ladder circuit that has been saved in the library file will be displayed.

Notes

・The library file that you can read is the file of a model that carries the same current library window.

5. Like the [Program : Ladder] window, to modify the ladder circuit, use the button of the toolbar for

editing ladder, the command of the [Instruction] menu, and the function key.

6 ・32


(1) Edit ladder circuit

The editing method of the ladder circuit at the [Read from Library] window is same as the [Register library] window. Refer to the page 6-29.

(2) Setup increase /decrease value

The setup method of the increase /decrease value at the [Read from Library] window is same as the [Register library] window. Refer to the pages 6-29 to 30.

(3) Save library file

To save the file with the same name as the library file that was read, click [File]-[Save] of the menu bar.

To save the file with the different name to the library file that was read, click [File]-[Save As] of the menu bar.

⇒ [Register library file] dialog box will be displayed.

If you click [Save] button after setting up the place (directory) to save first, and then inputting the file name, it will be saved in a file. (file of the extension lb2)

Also, the line comment file is also created at the same time. (file of the extension lbc)

(4) Read to the [Program : Ladder] window

Read the ladder circuit created at the [Read from Library] to the [Program : Ladder] window.

1. Click [Insert]-[Insert] of the menu bar.

⇒ [Insert Library] dialog box will be displayed.

6 ・33


2. Assign the reading position.

□ Insert to Cursor Position.

Read out to the row that contains the cell cursor of the [Program : Ladder] window.

□ Insert to Assigned Row.

Read out to the assigned row of the [Program : Ladder] window.

3. When there is a ladder circuit on the assigned line of the [Program : Ladder] window, select

either "over write" on the ladder circuit, or "insert" in front of the ladder circuit.

4. Setup the number of times of the ladder circuit being read continuously on the "repeat time."

In case you setup more than two times, read out by increasing /decreasing the relay

address or the register address , according to the number of increased/ decreased value.

If the number of repeat is one time, the increase /decrease value will not be affected.

5. If you click [OK] button, the reading of the ladder circuit to the [Program : Ladder] window will

start.

Example of the number of repeat being three times.

First reading

Second reading

Third reading

6 ・34


You can adjust the display position of the output instruction (OUT instruction, /application instruction, etc...) which was created at the [Program : Ladder] window, or you can execute the automatic connection of the disconnected circuit or optimization of the ladder.

1. Display the ladder circuit at the [Program : Ladder] window.

2. Click [Display]-[Arrange Ladder Diagram] of the menu bar.

⇒ [Arrange Ladder Diagram] dialog box will be displayed.

3. If you click the [Exec.] button after checking the item to execute by the mouse, the ladder will

be arranged.

(1) Connection of the disconnected circuit

Connect the disconnected circuit. Only the horizontal line will be connected, however, and the vertical line will not be connected.

Connection

(2) Adjustment of the display position

Adjust the display position of OUT instruction, TMR /CNT instruction, and application instruction.

You can either setup the display position by the [Open] button in the [Arrange Ladder Diagram] dialog box, or by the [Setup Display] dialog box which can be displayed by clicking [Setup]-[Setup

Display] of the menu bar.

6 ・35


Assign the display position of the coil (OUT instruction)

□ Align display

The coil display position is set according to the screen size.

the screen become the display position of the coil. And when the setup is "Align right," the first cell from the right of the screen will become the display position of the coil.

If the number of contacts of the horizontal direction exceed the screen size, the display position will be set according to the number of the contacts. (The display position of coil will be set outside the screen)

□ Specify Position

Assign the display position of the coil by the row number (0 to 61).

If the number of contacts of the horizontal direction exceed the assigned number, the display position will be set according to the number of the contacts.

Assign the display position of TMR /CNT instruction and application instruction.

□ Align left

The display position of TMR /CNT instruction number and application instruction number will be the display position of coil (OUT instruction).

□ Align right

The display position of TMR /CNT instruction number and application instruction number will be the 4 th number from the left of the display position of coil (OUT instruction).

Example 1) Display position : arrange to the screen size Arrange position : Arrange in front

Example 2) Display position : assign position (row number 5) Arrange position : Arrange in back

6 ・36


(3) Re-arranglment of MCS, JCS condition's display

Check the area where the condition of MCS (F-30) and JCS (F-41) is valid, and display "M"

(MCS), "J" (JCS) to the line number of the valid area.

Example 1) Using MCS Example 2) Using JCS

Nesting level

"M" mark

Nesting level

"J" mark

(4) Re-arrangement of ladder diagram's layout

Omit unnecessary horizontal lines, and gather the ladder elements towards left.

Re-arrangement

6 ・37


Change the ladder diagram created at the [Program : Ladder] window to the mnemonic.

Converting Ladder to the Mnemonic is taken place in the following timing.

① When transferring the program to the PC (right before the transfer).

② When saving the program in the file (right before the saving).

③ When clicking the button of the toolbar for editing ladder.

④ When the program check is executed by clicking [Edit]-[Program Check] of the menu bar, or by

clicking the button of the main toolbar.

⑤ When clicking the [Display]-[Data List] of the menu bar.

⑥ When changing the window to the [Program : Mnemonic] window by clicking the [Display]-

[Change Display] of the menu bar ,or clicking the button of the main toolbar after editing

the ladder.When this operation takes place, the following dialog box will be displayed.

If you click [Yes] button here, the window changes to the [Program : Mnemonic] window, and

the mnemonic program will be displayed. If you click [No] button here, the mnemonic program

before the creation or the modification of the ladder will be displayed.

⑦ Before word-wrapping.

⑧ Before changing the model.

(Example of the change to mnemonic)

Convert

Ladder program Mnemonic program

6 ・38


Notes

If there is a ladder circuit (disconnected line, etc.) that can not be changed to the mnemonic when converting ladder to mnemonic, an error message (compile error) will be displayed, and this particular ladder program will not be changed to the mnemonic.

In this case, the transfer to the PC or the printing will not take place, however, the saving in the file will take place.

(Example of compile error)

maternal line (0 column).

6 ・39


You can draw freely the ladder diagram in the ladder diagram display area, but when this freely drawn ladder diagram is modified to be looked better, the ladder is said to be "optimized."

[1] Circuit by the Optimization

If you execute the optimization, the ladder diagram will become the following.

① All contacts will be crammed at upper and at the left side, and unnecessary horizontal lines・

vertical lines will be deleted.

② The position of OUT instruction, TMR /CNT instruction and application instruction will all move to

the position of the corresponding window size which was adjusted to the optimization. Depends

of the size, the horizontal line ・vertical line will be either added or deleted. The actual display

position is at the fourth number from the right of the screen, but if there are many AND contacts,

the display position will be set outside the screen.

(Example of optimization)

Optimization

6 ・40


[2] Optimization Timing

The ladder optimization is executed at the time of "converting mnemonic to ladder."

Therefore, follow the following order when you are displaying the optimized ladder diagram which had been already been created .

① Create ladder drawing at the [Program : Ladder] window.

② Change the window to the [Program : Mnemonic] window after clicking [Display]-[Change

Display] of the menu bar or button of the main toolbar to change the ladder to the mnemonic.

③ Click button of the toolbar for editing mnemonic, and change it to the ladder.

④ Click [Display]-[Change Display] of the menu bar, or click button of the main toolbar, and

change the window to the [Program : Ladder] window.

Notes

When changing from mnemonic to ladder, the content (coil display position) that was setup by [Setup]-

[Setup Display] of the menu bar are invalid. To validate this setup, execute [Display]-[Arrange Ladder

Diagram] of the menu bar at the [Program : Ladder] window.

6 ・41

Chapter 6 Program Edit (Mnemonic Programming)

6-2 Mnemonic programming

If you click [Display]-[Change Display] of the menu bar when the [Program : Ladder] window is being displayed, the [Program : Mnemonic] window will be displayed.

Program address Mnemonic Symbol Toolbar for editing mnemonic

・The symbol which was registered at the [Symbol] window (the same file name as the [Program :

Mnemonic] window) will be displayed.

The input by the mnemonic is executed in the following order.

1.

Select the program address that you want to input.

・Select the program address with [↑][↓] keys, or click by the mouse.

2. Select the instruction that you want to input.

・There are three methods to select the instruction.

① Select the [Instruction] menu command. (STR, AND, etc...)

② Click the toolbar for editing mnemonic.

③ Press the function key.

F2 : STR F3 : AND F4 : OR F5 : NOT

F6 : TMR F7 : CNT F8 : FUN F9 : OUT

・ The inputs of compound instructions (STR NOT, AND STR, STR TMR, OR NOT CNT,

etc...) will be executed by repeating the order described above.

6 ・42


・If you click the button or the [F1] key after inputting TMR /CNT instructions, the display

will change to the following order.

TMR → DTMR (BCD) → DTMR (BIN) → UTMR (BCD) → UTMR (BIN)

CNT → DCNT (BCD) → DCNT (BIN) → UCNT (BCD) → UCNT (BIN)

・If you input an instruction, the spot where numerical values such as relay or register number,

timer /counter number and application instruction number will be waiting for the input.

3. Input relay or register number, timer ・counter number, or application instruction number, and

then press the [Enter] key.

(Example of inputting address)

K i n d




V a l u e

S e t u p

E x a m p l e

0 0 0 0 1

0 0 0 1

0 0 0 1

[ 1 ] [ E n t e r ]

[ 1 ] [ E n t e r ]

[ 1 ] [ E n t e r ]

I n p u t


N u m b e r



F 0 0 0

F c 0 1 2 w

] 0 0 0 1 b 0 0 0 1

0 9 0 0 1

E 0 0 0 1

@ 9 9 0 0 0

[ F ] [ 0 ] [ E n t e r ] o r [ 0 ] [ E n t e r ]

[ F ] o r

[ C ]

[ C ]

[ 1 ]

[ 1 ]

[ 2 ]

[ 2 ]

[ W ]

[ W ]

[ E n t e r ]

[ E n t e r ]

[ ] ] [ 1 ] [ E n t e r ]

[ B ] [ 1 ] [ E n t e r ]

[ 0 ] [ 9 ] [ 1 ] [ E n t e r ]

[ E ] [ 1 ] [ E n t e r ]

[ @ ] [ 9 ] [ 9 ] [ 0 ] [ E n t e r ]

A p p

C o n s il c a t t a n i t o n I n s t r u c t i o n

N u m b e r

0 0 1 [ 1 ] [ E n t e r ]

・There are no differences between upper and lower cases of [F], [C], [X], [W], [D], [B], [E].

・Select the cell in which the register is displayed, and if you input the [F1] key, the register

area will change in the following order.

]0000 → b0000 → 09000 → 19000 → … → 99000 → E0000

・All mnemonic editing will be operated in program address module. You can select several

program addresses by the dragging operation.

・You can insert the NOP instruction by selecting the [Insert Row] command of the [Edit] menu, or

by selecting the [Insert] key.

・You can delete the instruction by selecting the [Delete Row] command of the [Edit] menu, or by

selecting the [Delete] key, However, you can not delete from the 2 nd to the fourth words of the

2 to 3-word instructions.

・You can copy or move the instruction by selecting the [Cut], [Copy], [Paste] commands of the

[Edit] menu.

6 ・43


Convert the mnemonic program that was created at the [Program : Mnemonic] window to the ladder diagram.

Converting mnemonic to ladder is executed in the following timings.

① At the time of transferring the program from the PC (right after the transfer)

② At the time of reading the program from the file (right after the reading)

③ When clicking the button of the toolbar for editing mnemonic.

④ When changing the window to the [Program : Ladder] window by clicking the [Display]-[Change

Display] of the menu bar, or clicking the button of the main toolbar after editing the mnemonic.

If you execute this operation, the following dialog box will be displayed.

If you click the [Yes] button here, the window will change to the [Program : Ladder] window, and

the ladder diagram will be displayed. If you click the [No] button here, the ladder diagram before

the creation or modification of the mnemonic program will be displayed.

In addition, if you display the ladder diagram after having the mnemonic changed to the ladder , the ladder will be optimized and displayed. (Refer to the page 6-40 for "optimization of ladder.")

(Example of the change to the ladder)

Mnemonic program

Convert

Ladder program

6 ・44


Notes

If there is a mnemonic program that can not be changed to the ladder when converting mnemonic to ladder, an error message (compile error) will be displayed, and the mnemonic program will not be changed to the ladder. However, when you transfer the program from the PC, or reading the program from the file, it will be changed to the ladder (abnormal ladder) .

(Example of the compile error)

6 ・45

Chapter 6 Program Edit (Notes When Editing Program)

6-3 Notes When Editing Program

You can read several parts of the ladder diagram at the same time when you open several windows by the program of the same name. You can edit easily, for example, the "copy circuit" by looking at the two windows. However, the editing result from the active window will be reflected to an another window when you change (when you press the button, etc...) from ladder to mnemonic, or change from mnemonic to ladder.

1. When the windows other than the [Program: Ladder]/[Program: Mnemonic] windows are minimized and when the [Program: Ladder] window is active, click [Window]-[Open New

Window] of the menu bar.

⇒ The second [Program: Ladder] window will be opened.

2. Click [Window]-[Display in Row] of the menu bar.

⇒ Two [Program: Ladder] windows and a [Program: Mnemonic] window will be displayed.

6 ・46

Chapter 6 Program Edit (Notes When Editing Program)

3. Edit the program at the [Program: Ladder] window. At this moment, the editing result will not

be reflected to the other window.

Delete

Not deleted

Not deleted

4. If you click the button of the toolbar for editing ladder when the edited [Program: Ladder]

window is active, the editing result will be reflected to the other window.

6 ・47

Deleted

Deleted

Chapter 7 Setup Each Data (Setup System Memory)

Chapter 7 Setup Each Data

The setup of system memory,data memory,parameter,symbol /comment will be explained.

7-1 Setup System Memory

At the system memory window, the address/data/comment of the system memory will be displayed.

Address chart Data chart

Comment chart

・To edit the data, locate the area with the scroll bar, click the data cell, push the [Enter] key, and input the numerical value.

・During the monitoring (PC on-line), the memory volume of the PC will be displayed.

・The comment will display the already setup content each time .

(1) Operation at the system memory display area

・You can select one cell with single click.

・You can select several cells with drag.

・You can cut/copy/paste the selected area by the [Edit] menu , or by the shortcut menu which is displayed by clicking the right of the mouse.

(2) Select operation of display

You can operate the following using the [Display] menu or the toolbar for editing data.

・Select data display of the system memory from binary notation/octal notation/decimal notation

/hexadecimal notation, or ASCII.

・Select the data length of the system memory from byte/word/double word. This selection is all valid in the display area of the system memory.

・Select either display as a list (display several data in one line) or display in detail (display one data and its comment in one line.)

7 ・1


Setup/display the system memory by the property sheet type.

The property sheet will be displayed when you click [Property Sheet] of the tree bar.

Depends on the PC model, the setup item/content will be different.

Click [Property Sheet]

(PC mode : JW30H display)

Setup Item (JW30H)

Timer , Counter

Area Setup

Communication Port

Error Processing

Interruption

ROM Operation

Other Setup

Content

Timer's reset condition, 10 ms timer function, Counter's reset condition

Latched relay area, Output hold address, Comment memory (kinds)

Port 1/2 (transfer rate, parity, stop bit, station numbe)

Continues operation ( at fuse blown, at option module error, at I/O link master station error), Allowable power interruption time

Timer Interruption, Condition of input interruption

ROM operation mode, Contents stored in ROM

Constant scan, Top address of rack

Operation Button

OK

Renew

Cancel

Content

Data of system memory is modified, and the property sheet will be closed.

Data of system memory is modified, but the property sheet will not be closed.

Teh Setup Content will not be modified, but the property sheet will be closed.

7 ・2


■

(JW50/70/100,JW50H/70H/100H)

In case of JW50/70/100 and JW50H/70H/100H, you can setup the kind/points of the module that is to be put on each rack/slot when using the JW input/output module.

You can do the setup at the displaying [Manual I/O Registration] dialog box after clicking the [Manual I/O

Registration] of the tree bar.

Click [Manual I/O Registration]

(PC model ：JW50/70/100,

JW50H/70H/100H display)

● [Manual I/O Registration] dialog box

Rack tab

Module establishing button

Summary chart

Front address establishing button

OK button

Item/Button of Setup /Operation

Rack Tab

Slot No.

Select the rack number (0 to 7)

Select the slot number.

Type of Module

Select the kinds of module from "input, output, special I/O (input, output, input /output), dummy, no I/O."

Points

Top address of Special I/O

Data Register

Select the points in 16-point module.

Setup top address of the register for changing data with the special I/O module.

Module establishing button

・The setup is valid when selecting the "special I/O" by the type of module.

The content of the setup unit will be displayed in the summary chart.

Top address of Rack

Setup the top address of rack

Front address establishing button

・The setup is valid when the rack number is between 1 and 7.

The top address of the setup rack will be displayed in the summary chart.

Summary Chart

If you click module establishing button/top address establishing button, setup/modified "slot number, kind of module, points, I/O address" will be displayed in the selected rack.

OK button

Open the [Confirmation (Manual I/O Registration)] dialog box to confirm the settings. ⇒ Refer to the next page.

7 ・3


● [Confirmation (Manual I/O Registration)] dialog box

Change display

Button Function

Change display Switch the view between racks 0 to 3 and racks 4 to 7.

Confirmation Realize the settings in the system memory.

Confirmation

7 ・4

Chapter 7 Setup Each Data (Setup Data Memory)

7-2 Setup Data Memory

At the data memory window, the address/data/symbol/comment of the data memory will be displayed.

Address chart Data chart Symbol chart Comment chart

Tree

(PC model : JW-33CUH1 display)

・Select relay, timer /counter, register, file register by the tree of the tree bar. In addition, select the register area (]0000,b0000,09000,19000 … 99000, E0000) at the register, and select file area

(FILE 1, FILE 2 … ) at the file register.

・To edit the data, locate the area with the scroll bar, and click the data cell. If you want to edit the register data, push the [Enter] key, and input the numerical value.


・At the symbol chart or the comment chart, the data memory that was registered at the [Symbol] window will be displayed. You can also input characters directly in the symbol chart or the comment chart.

(1) Operation at the data memory display area



・You can cut/copy/paste the selected area by the [Edit] menu, or by the shortcut menu which is displayed by clicking the right of the mouse.


You can operate the following using the [View] menu or the toolbar for editing data.

・Select data display of the data memory from binary notation/octal notation/decimal notation/ decimal notation (with +-)/ hexadecimal notation, or ASCII.

・Select the data length of the data memory from byte/word/double word. This selection is all valid in the display area of the system memory

・Select either display as a list (display several data in one line) or display in detail (display one data and its symbol /comment in one line.)

7 ・5

Chapter 7 Setup Each Data (Setup Symbol/Comment)

7-3 Setup Symbol/Comment

■ Summary Display/Operation of Symbol/Comment

At the symbol ・comment window, the address/symbol/comment of the data memory will be displayed.

Address chart Symbol chart

Comment chart

Tree


・Select relay, timer/counter, register, file register by the tree of the tree bar. In addition, select the register area (]0000,b0000,09000,19000 … 99000, E0000) at the register, and select flie area

(FILE 1, FILE 2 … ) at the file register.

・To input or edit the symbol or comment, locate the area with the scroll bar, click the data cell, push the [Enter] key, and input the characters.

・You can register maximum symbols at 16 characters, and maximum comments at 28 characters.

・Up to maximum 32000 symbol/comment s can be registered.

・If you setup "Input symbol check is done" at the [Setup]-[Check Input's Same Symbol] of the menu bar, the confirmation dialog box will be displayed at the time of inputting the same symbol.



・You can cut /copy /paste the selected area by the [Edit] menu , or by the shortcut menu which is displayed by clicking the right of the mouse.

7 ・6

Chapter 7 Setup Each Data (Setup Symbol/Comment)

You can use the text file (file of the extension txt) as the user file of the symbol/comment.

(1) Register to the text file

Describe the data memory address, symbol and comment in one line, and they are divided by the tab.

Data memory address [Tab] Symbol [Tab] Comment [Enter]

Example) An example when created by Microsoft Word 97

＊Microsoft Word is the registered product of Microsoft

Corporation, America.

00000 LS00

00013 LS13

Rising side limit 0

Retreating side limit 13

]0100 DISP Display machine output

59000 ERROR Register error

Symbol Comment

Address (possible for zero suppress, valid for same address which comes after.)

Created documents are saved in the file by "text＋return (＊.txt) type."

(2) Read text file

Import the file by selecting [File]-[Import].

The file kind is "Symbol/Comment (Text type)( ＊.txt)."

7 ・7

Chapter 7 Setup Each Data (Setup Parameter)

7-4 Setup Parameter

In case of the PC model series JW20/JW30H, the parameter of the special I/O module/option module is setup at the parameter window. (In other model series, the parameter window is not used.)

At the parameter window, the address and data will be displayed.

Address chart

Data chart


・To edit the data, locate the area with the scroll bar, click the data cell, push the [Enter] key, and input the numerical values.


(1) Operation in the parameter display area



・You can cut/copy/paste the selected area by the [Edit] menu , or by the shortcut menu which is displayed by clicking the right of the mouse.



・Select data display of the data memory from binary notation/octal notation/decimal notation/ decimal notation (with +-)/ hexadecimal notation, or ASCII.

・Select the data length of the parameter from byte/word/double word. This selection is all valid in the display area of the parameter.

7 ・8


■ Setup Model

(Special I/O module/option module)

Setup the model of the special I/O module and the option module at each switch number.

If you click [Model setup list] of the tree bar, the [Model Setup List] dialog box will be displayed.

Click [Model setup list]

(PC model : JW-30H display)

Tab

Summary chart

(PC model : JW30H display)

・"Select special I/O or option" and "select switch number and module name (model name)" are

executed.

Setup/Operation Item/Button

Tab

Switch No.

Module name

Content

Select“special I/O”or“option.”

Select the number of the module No. switch.

Select the classification of the module in the module name.

Model name

Decide Button

Select the classification of the module in the model name.

Write the selected the module name/model name to the summary chart.

Summary Chart

Clear Setup

Display the module name/model name that were selected by each switch number

Clear all content that was setup in the summary chart.

7 ・9


Setup/display the parameter in property sheet type.

If you click [Property sheet] of the switch number (special I/O /option) which is to be assigned, the property sheet that was setup at the [Model setup list] will be displayed.

Click [Property Sheet]

(PC model : JW30H display)

(Display PC model : JW30H, module name : JW-21HC (mode 0, 3, 5))

・Depends on each module, the setup content of the property sheet varies.

Notes

・The parameter that is setup by the property sheet is the parameter that will be stored in the main PC.

There is an module that stores the parameter inside the module. In this case, setup at the "Option

parameter tool" window. ⇒ Refer to the next page.

7 ・10

Chapter 7 Setup Each Data (Setup Option Parameter Tools)

7-5 Setup Option Parameter Tools

For the model that saves parameters in the option module, set the parameters with option parameter tools.

・Select [Tool]-[Option Parameter], and the [Option Parameter tool] windows is displayed.

・Select [File]-[New], and select the type of option module to set the parameters. If you already have a file of option parameters, open it by selecting [File]-[Open].

[New] dialog box

[Open] dialog box

7 ・11


・In the [Option Parameter Tool] window, the addresses, the data, and the comments are displayed.

Address chart Data chart Comment chart

(Example for display: Data link master station)

・To edit the data, locate the area with the scroll bar, click the data cell, push the [Enter] key, and input the numerical values.

(1) Operation in the area of option parameters

You can select one cell with single click.

(2) Selection of display

You can perform the operations below with the [Display] menu or toolbar for editing data.

・Select the data view of parameters from binary notation/octal notation/decimal notation/decimal notation (with +-)/ hexadecimal notation, or ASCII.

・Select the data length of parameters from bytes/words/double words. This selection works in all the display area of parameters.

(3) [New]/[Open]/[Close] in the [File] menu

You can set parameters of several option modules in a single option parameter tool.

Select [File]-[New], open the [New] dialog box, and select the type of option module.

(4) Model selection in the [File] menu

Select the model of the CU unit you will equip with the option module.

(5) Sending of the [PC] menu

Connect the personal computer to the option module, and read/write/verify the parameters.

7 ・12


(6) Operation settings of the [PC] menu

Item Function

Start of Link

Stop of Link

Start after writing

EEPROM

Start the link operation

Stop the link operation

Stat the link operation after writing the parameters into EEPROM in the option module.

Writing EEPROM Write the parameters into EEPROM in the option module.

Parameter initialization Initialize the parameters in the option module.

(7) Start/Stop of the [PC] menu

Start or stop the PC.

You can set up or display the option parameters in the property sheet form.

Select [Display]-[Property Sheet]. The property sheet of the option module that is currently active is displayed.

(Display example: Property Sheet of Data Link Master)

・Items in the property sheet vary according to the type of option module. For the details of the parameter sheet, refer to the manuals of the option module.

7 ・13

Chapter 8 Monitor (Start Monitoring, Stop Monitoring)


By connecting the PC and the personal computer, you can monitor the ON/OFF condition of the relay, or monitor the current value of the register. Before monitoring, execute the "communication setup" first. (Refer to the page 5-48)

If you click [Monitor] of the menu bar at the main/program/system/data/parameter window, the [Monitor] menu summary will be displayed.

(Details in pages)

8-1

8-1

8-24

8-26

・In the [Main] window, you can select

[I/O Forced Processing] only.

← Only the [Program : Ladder] window

8-1 Start Monitoring, Stop Monitoring

(Program/System/Data/Parameter)

Start/stop the monitor of the active window.

・Only start/stop the monitor of the active window, and it does not affect to the other window.

[1] Monitor at the [Program :Ladder] window

The [Program : Ladder] window is organized by the line number (address number) and the display area of the ladder.

(1) Monitor Display

When the circuit is running, a thick line is displayed, and when the circuit is not running, a thin line is displayed.

Display the monitor by the monitor display type and the register display type that were setup at the

[Setup Monitor Display Mode] dialog box.

Input line

Current Value

Notation Display

Display Content

When the input of the application instruction is running, a thick line is displayed, and when the circuit is not running, a thin line is displayed.

The current value of the register by the notation type of the setup at the register display type will be displayed at the top of register.

When the setup of the monitor display type is the detail display, the notation of the current value will be displayed.

・Display example Not Running Condition

Running Condition

(Simple display)

8 ・1

Current value

(Detail display)

Notation of the current value


Notes

・Before monitoring, read the program from the PC by the PC transfer (Refer to the page 5-59) or write the program to the PC. If the program of both the PC and the personal computer is different, you can not monitor the right calculation.

(2) Set/ reset of the relay

Set/reset the relay of the cursor position.

① Move the cursor to the relay where you are going to set/ reset.

② Click the right side of the mouse.

⇒ The "set/ reset relay" menu will be displayed.

・If you click [Sets relay] or [Resets relay], the relay of the cursor position will be set/ reset.

8 ・2


[2] Monitor at [Program : Mnemonic] window

The [Program : Mnemonic] window is organized by the display area of the address number and the mnemonic.

When the circuit is running, a " ＊" will be displayed, and when the circuit is not running, a "−" will be displayed.

Current Value

Display Content

The current value of the register will be displayed at the right side of the register.

Notation Display The notation of the current value will be displayed at the right side of the register .

Running condition

Not running condition

(Display example)

Notation of the current value

Current value

Notes

・Before monitoring, read the program of the PC by the PC transfer (Refer to the page 5-59) or write the program to the PC. If the program of both the PC and the personal computer is different, you can not monitor the right calculation.

8 ・3


[3] Monitor at the [System] window

Data items are renewed by communicating with the PC, and following the assigned monitor type.

If you double-click the data cell, or select the cell and push the [Enter] key, the item will become the input mode. If you input the [Enter] key after inputting an optional numerical value at the input mode, the system memory value of the PC will be modified.

If you use the [Display] menu or the toolbar for editing data, you can select the display type of the system memory from binary notation/octal notation/decimal notation/hexa decimal notation, or

ASCII. This selection is all valid in the display area of the system memory.

If you use the [Display] menu or the toolbar for editing data, you can select the data length of the system memory from byte/word/double word. This selection is all valid in the display area of the system memory.

If you use the [Display] menu or the toolbar for editing data, you can select either summary display

(display several data in one row) or detail display (display one data and its comment in one row.)

You can cut/copy/paste the selected area by the [Edit] menu , or by the shortcut menu which is displayed by clicking the right side of the mouse.

Notes

・By the operations described above at the time of the monitor, the value of the connected PC will be

modified at the same time.

8 ・4


[4] Monitor at the [Data] window


If you double-click the cell whose register is being monitored, or select the cell and push the

[Enter] key, the item will become the input mode. If you input the [Enter] key after inputting an optional numerical value at the input mode, the data memory value of the PC will be modified.

if you click on the right side of the mouse on the line monitoring the timer ・counter, the short cut menu that carries set/reset as their items will be displayed. If you select set/reset by this menu, you can set/reset the timer ・counter.

If you click on the right side of the mouse on the line monitoring the relay, the short cut menu that carries set/reset as their items will be displayed. If you select set/reset by this menu, you can set/ reset the relay.

If you use the [Display] menu or the toolbar for editing data, you can select the display type of the system memory from binary notation/octal notation/decimal notation/decimal notation (with a plus/ minus sign)/hexadecimal notation, or ASCII.

If you use the [Display] menu or the toolbar for editing data, you can select the data length of the data memory in byte/word/double word. This selection is all valid in the display area of the data memory.

If you use the [Display] menu or the toolbar for editing data, you can select either summary display

(display several data in one row) or detail display (display one data and its symbol /comment in one row.)

● Edit operation

You can cut/copy/paste the selected area by the [Edit] menu , or by the shortcut menu which is displayed by clicking the right side of the mouse.

Notes

・By the operations described above at the time of the monitor, connected value of the main PC will be

modified at the same time.

8 ・5


[5] Monitor at the [Parameter] window


If you double-click the data cell, or select the cell and push the [Enter] key, the item will become the input mode. If you input the [Enter] key after inputting an optional numerical value at the input mode, the parameter value of the PC will be modified.


・Select the display type of the parameter from binary notation/octal notation/decimal notation/

decimal notation (with a plus/minus sign)/hexadecimal notation, or ASCII. This selection works

in the all display area of the parameter.

・Select the data length of the parameter from byte/word/double word. This selection is all valid

in the display area of the parameter.

You can cut/copy/paste the selected area by the [Edit] menu , or by the shortcut menu which is displayed by clicking the right of the mouse.

Notes

・By modifying the operations described above at the time of the monitor (only when the PC is stopping), the value of the connected PC will be modified at the same time.

8 ・6


[6] Monitor Several Windows at the Same Time

You can monitor several windows at the same time. However, you cannot monitor the

[Program:Ladder] window and the [Program:Mnemonic] window at the same time.

・Display example ※

Operate start/stop of the monitor by the [Monitor] menu at every window (described above ※).

8 ・7

Chapter 8 Monitor (Multipoints Monitor)

8-2 Multipoints Monitor

[1] Function

You can monitor manual data in the data memory or system memory (maximum 128 items).

(Display example)

Data items are renewed by communicating with the PC, and following the assigned monitor type at each row.

Item

Address

Data

Content

Register the address to be monitored.

●Input method

・You can input the address to be monitored directly in the address cell.

・Right-click the address to be monitored in each of the

Program:Ladder/System/Data/Symbol windows of JW-100SP. In the short

cut menu, select [Send]-[Multipoints Monitor].

⇒ Refer to the Sample Operation 1.

・Select the cell including the address to be monitored in the

Program:Ladder window of JW-100SP, and select [Tool]-[Multipoints

Monitor] in the menu bar.

⇒ Refer to the Sample Operation 2.

Data items are renewed by communicating with the PC, and following the assigned monitor type at each line.You can modify the current value of the register, set/ reset of the timer ･counter, and set/ reset of the relay.

●Modify data of register

If you double-click the cell monitoring the register or select the cell and

push the [Enter] key, "data item will change to the input mode. If you input

the [Enter] key after inputting an optional numerical value at the input

mode, you can change data. During the monitoring, you can also change

data of the PC at the same time .

●Set/reset of the relay if you click on the right side of the mouse on the line monitoring the relay, the short cut menu that carries set/reset as their items will be displayed. If you select set/reset by this menu, you can set/reset the relay.

(To next page)

8 ・8


Item

Supplement

Content

Change the display type of the register, and set/reset the timer /counter contact.

●Changing the display type of the register

Right-click the cell of the register address, and select the display type in

the short cut menu. The numerical value of the data cell of the register

address is displayed in the specified display form.

・You can select the display type of the system memory from binary

notation/octal notation/decimal notation/decimal notation (with a

plus/minus sign)/hexadecimal notation, or ASCII.

●Set/reset of the timer /counter contact

If you right-click the cell monitoring the timer counter, the short cut menu

that carries set/reset as their items will be displayed. If you select set/reset

in this menu, you can set/reset the timer /counter.

Symbol

Comment

Displayed when the symbol/comment is setup at the register data.

・Sample Operation 1 (To send from the data memory window to multipoints monitor)

If you right-click the address to be monitored in the Data Memory window of JW-100SP and

select [Send]-[Multipoints Monitor], the address will be displayed in the multipoints monitor.

8 ・9


・Sample Operation 2 (To start with the menu bar of the Program:Ladder window)

8 ・10


[2] Menu operation

The menu operation of the [Multipoints Monitor] window (cf. page 8-8) is explained.

(1) Menu bar

(Refer to:) 8-11 8-12 8-13 8-13 8-13 8-14

Item

Open

Save

Save As

Quit

Content

Open an existing file(*.mon)

Overwrite and save the current file.

Save the address registered in the [Multipoints Monitor] window, specifying the filename and the folder.

Close the [Multipoints Monitor] window.

Note: Addresses that has been added, modified, or deleted after the previous [Save] or [Save As] is not saved.

8 ・11


Item

Cut

Copy

Paste

Repeat to forword

Repeat to rewind

Content

Cut the selected area of the address cell, and save it in the clipboard.

Copy the selected area of the address cell, and save it in the clipboard.

Paste the data saved in the clipboard.

Register the 15 downward consecutive addresses from the selected cell.

Register the 15 upward consecutive addresses from the selected cell.

See below.

Execute

[Downward sequence].

(After executing [Downward sequence])

Execute

[Upward sequence].

8 ・12

(After executing [Upward sequence])


Item

Displays in Byte

Displays in Word

Displays in

Double Word

Tool Bar

Status Bar

Content

Display the value of system memory, register address, or timer /counter by bytes.

Display the value of system memory, register address, or timer /counter by words.

Display the value of system memory, register address, or timer /counter by double words.

Select ON/OFF of the display of the tool bar.

Select ON/OFF of the display of the status bar.

Item

Start Monitoring

Stop Monitoring

Content

Start monitoring

Stop monitoring

Item Content

Define the model name of PC to be monitored.

Model setup

・If you start by selecting [Tool]-[Multipoints Monitor] or [Send]-

[Multipoints Monitor] in JW-100SP, you cannot change the model.

(It will be the model in operation with JW-100SP.)

・Registered addresses are all deleted.

8 ・13


Item

Version data

(2) Tool bar

Content

Display the version of the multipoints monitor.

(See page)

◎

◎

(3) Status bar

Display one-line help when a menu or toolbar icon is selected.

8 ・14

Chapter 8 Monitor (Sampling Trace)

8-3 Sampling Trace

Sampling trace displays data in PC (e.g. ON/OFF information of relay) in the form of time charts. You can also save or print the displayed data.

If you click [Monitor]-[Sampling Trace] (refer to page 8-20) according to the procedure of sampling trace on the next page, sampling trace will start.

(Display example)

Trigger condition

Trace data address

※ 4 ※ 1 ※ 2 ※ 3

Trace data cursor

※ 1 Data at the previous position of the trace data cursor

※ 2 Data at the position of the trace data cursor

※ 3 Data at the next position of the trace data cursor

You can change the display type of ※ 1 to ※ 3 to binary notation/octal notation/

decimal notation/hexadecimal notation.

※ 4 Situation at the position of the trace data cursor

・Relay: Display for ON, for OFF.

・Register: Display data in hexadecimal notation (fixed).

8 ・15


[1] Sampling Trace order

The order to execute sampling trace will be explained.

1 .

・ Setup the compatible PC model by the [Setup]-[Select PC Model] of the menu bar.

・ If you start sampling trace in JW-100SP, you cannot change models. (It will be the model in

operation with JW-100SP.)

2 .

Set up communication by selecting [Setup]-[Communication Setup] in the menu bar.

3 .

Edit the trigger condition by selecting [Edit]-[Trigger Condition] in the menu bar.

・Create a ladder program to be the trigger condition. You do not have to create a coil (OUT instruction).

・The ladder program that can be the trigger condition has maximum five contacts. You cannot input ladder mnemonics in the highlighted area below.

You cannot input ladder mnemonics in the cell of the highlighted area.

(Program Example)

B A

When the ladder mnemonic of A is input, the B cell is highlighted.

Switch to the Sampling

Condition window.

・Click [Switch to the Sampling Condition window] in the tool bar.

8 ・16


4 .

Set up trace memory file, trace memory capacity, sampling frequency, and trigger mode by selecting [Setup]-[Trace Condition Setup].

5 .

Register the address to be traced in the input module of trace data address.

Address input cell

If you select an address input cell and push the [Enter] key, if you double-click a cell, or if you rightclick a cell and select [Input/modify] in the popup menu, the [Input Address] dialog box will be displayed.

Input the address to be traced in the [Address] area in the [Input Address] dialog box.

If you click ▼ on the right of the [Address] area, you can select a register address in the list.

To delete the address, select the cell containing the address you want to delete and push the

[Delete] key, or right-click the cell and select [Delete] in the popup menu.

8 ・17


6 .

If you click [Monitor]-[Sampling Trace] in the menu bar, the [Sampling Trace Process] dialog box will be displayed. If the trigger condition is not satisfied at this time, an arrow points “Wait for trigger” in the dialog box. This state remains until the trigger condition is satisfied.

・When the trigger condition is satisfied, the arrow moves [Tracing] →[Transfer data]→[Convert data] in the [Sampling Trace Process] dialog box. When the sampling trace processing is completed, sampling data is displayed in the display area.

(Program Example)

8 ・18


[2] Menu of the [Sampling Trace] window

This subsection explains menu operation of the [Sampling Trace] window (See page 8-15).

(1) Menu bar

■

■

Item

Open

Save

Save As

Print

Print Preview

Print Setup

Quit

Content

Open an existing file(*.smp) of trace data of sampling trace, trigger condition, or trace condition.

・Sampling trace will be executed for the model corresponding to the file you open.

Save trace data of sampling trace, trigger condition, or trace condition without changing the name or folder.

・You cannot select if a file is not open.

Save trace data of sampling trace, trigger condition, or trace condition, specifying the name or folder.

Print trace data.

Display the print image.

Select and set up the printer.

Close sampling trace.

Item

Undo

Content

Disable the operation you have just done.

Trigger Condition Set up the trigger condition. (Refer to page 8-16)

8 ・19


■

Item Content

Read the trace condition and trigger condition set in the PC.

Download

PC Data

Setup Data

■

・If you click [Setup], trace data of sampling trace, trace

condition, and trigger condition is set to the content read from the PC.

Traced Data Read sampling trace data saved in the file register of the PC.

Sampling Trace Start tracing.

Item

Tool bar

Status bar

Data Display

Type

Zoom

Content

Select the display of tool bar (appear/disappear).

Select the display of status bar (appear/disappear).

Select the display type of the register value from binary notation/octal notation/ decimal notation/hexadecimal notation.

Select the scale of the display area from standard/twice/four times.

8 ・20


■

Item Content

To set up sampling trace, click [Setup the Trace condition]. The [Setup] dialog box will be displayed.

Setup the Trace condition

Setup item

Trace Memory File

Content

Select the file register number to save the sampled data.

Use file F (2KB) in normal use.

Trace Memory

Capacity

Setup Sampling

Cycle

Trigger Mode

Define the capacity (KB) to use as trace memory from specified file register. The capacity is always 2KB when you use file F.

Define sampling frequency.

You can select [Every cycle] or [0 to 1000ms] in 10ms steps.

Select the trigger mode in sampling start.

Select the PC model name to execute sampling trace.

Model Change ・If you start by selecting [Tool]-[Sampling Trace] or [Send]-[Sampling Trace] in

JW-100SP, you cannot change the model.

(It will be the model in operation with JW-100SP.)

↓

To the next page

・Setup contents are all deleted.

8 ・21


Item Content

Set up communication between the personal computer and the PC.

Communication

Setup

Setup Item

COM.Port

Time Out

Speed

Content

Select the communication port connected to the communication adapter(JW-100SA).

Define the timeout duration of communication.

Select the communication speed.

・Communication speed is determined by model.

Assign shortcut keys of ladder mnemonics (A contact and B contact) when creating trigger condition.

Key Layout

■

Item

Version Data

(Sampling Trace)

Content

Display the version of sampling trace.

8 ・22


(2) Tool bar

← When sampling data is displayed

← When trigger condition is displayed

(See page)

◎Open Same as [File]-[Open] (8-19)

◎Save Same as [File]-[Save] (8-19)

◎Undo Same as [Edit]-[Undo] (8-19)

◎Execute Sampling Trace Same as [Monitor]-[Sampling Trace] (8-20)

◎Switch to Trigger Same as [Edit]-[Trigger Condition] (8-19)

Condition Window

◎Switch to Sampling Switch to sampling condition window

Condition Window

◎Displays in Binary Notation Same as [Display]-[Data Display Type]-[Displays in

Binary Notation] (8-20)

◎Displays in Octal Notation Same as [Display]-[Data Display Type]-[Displays in

Octal Notation] (8-20)

◎Displays in Decimal Notation Same as [Display]-[Data Display Type]-[Displays in

Decimal Notation] (8-20)

◎Displays in Hexa Notation Same as [Display]-[Data Display Type]-[Displays in

Hexa Notation] (8-20)

◎A Contact Used when inputting A contact in the trigger condition

setup window.

◎B Contact Used when inputting B contact in the trigger condition

setup window.

◎Eraser Used when erasing the circuit (cell unit).

◎Change Cursor Type Change the instruction cursor to the arrow cursor in

the trigger condition setup window.

◎Print Same as [File]-[Print] (8-19)

◎Print Preview Same as [File]-[Print Preview] (8-19)

◎Version Information Same as [Help]-[Version Data (Sampling)] (8-22)

8 ・23

Chapter 8 Monitor (I/O Forced Processing)

8-4 I/O Forced Processing

(Main/Program/System/Data/Parameter ：except JW10 model)

Turn ON/OFF the rely of the PC by force.

If you click [Monitor]-[I/O Forced Processing] of the menu bar of each window, the [I/O Forced

Processing] dialog box will be displayed.

Editing box

(Display example)

Execute the force treatment of the relay address that is displayed in the central editing box.

address that is displayed at the list of forced set/list of forced reset.

”

Button

Forced Set

Function

Execute the I/O force set of the relay address that is assigned in the editing box.

If the force set is executed normally, the relay address will be displayed in the list of forced set.

Forced Reset

Cancel 1 pt.

Execute the I/O force reset of the relay address that is assigned in the editing box. If the force reset is executed normally, the relay address will be displayed in the list of forced reset.

Release the I/O forced processing of the relay address that is assigned in the editing box. If the force release is normally executed, it is deleted from the list of forced set/reset.

Cancel All pts.

Release the whole relay addresses that are either force set /force reset from the

I/O forced processing.

8 ・24

Chapter 8 Monitor (Edit Program while Monitoring) sa

8-5 Edit Program while Monitoring

(Program)

You can edit program of the PC while monitoring. You can modify the part of a program of the PC faster by using this function, it is useful, for example, at the time of debug during the test running.

Ladder Monitor

PC Stopping PC Running

Mnemonic Monitor

PC Stopping PC Running

Change address or values specified

Edit Circuit

Transfer PC

(Program)

Read

Write

※

※

Possible

Possible

※

※

Possible

Impossible

Impossible Impossible

Impossible

Possible

Possible

Impossible

Possible

Impossible

※ "Change address or values specified" and "Edit Circuit" at the ladder monitor.

Model name W16/W51/W100

W70 H/W100H

JW series

Change address or values specified

Possible Possible

Impossible* Possible

* Due to limited processing capacity, the W16/W51/W100 series may stop operating if you try to modify the circuits during operation. Therefore, these models do not allow circuit modification during operation.

■ Precautions for editing circuits during operation

Modifying the circuits of a PLC while it is operating may cause serious accidents involving the machines or facilities which are controlled by this PLC due to missing program steps or inappropriate operation. Please be extremely careful when the PLC is operating.

Special precautions

・ Do not modify the program for a PLC that is controlling equipment which can directly cause damage to property or adversely affect human life.

・ Do not modify the program while operating if the scan time is longer than 100 mS.

(In some circuit editing conditions the control module may temporarily halt operation.)

・ Review the circuit and the address where you will insert a program step thoroughly. Simulate the operation of the new program using another device before making the actual change.

[1] Change address or values specified

・You can modify the contact and the coil relay number of the PC program while monitoring.

・It can be executed at the [Program：Ladder] window.

1. Activate the [Program ：Ladder] window.

2. Read program memory from the PC by the [PC Transfer]-[Read] command.

You can also write program created at JW-100SP to the program memory of the PC by the

[PC Transfer]-[Write] command.

3. Execute ladder monitor by the [Monitor]-[Start Monitoring] command.

4. After moving the cell cursor to the contact whose relay number is to be modified, or to the coil ,

press [Enter] key to make it to the address input mode.

5. If you press [Enter] key after inputting the relay number that is to be modified, the modification

of the relay number will be completed.

Change 00000 to 00002

8 ・25

Chapter 8 Monitor (Edit Program while Monitoring)

[2] Edit Circuit

・You can change, insert (add), delete the program (ladder circuit) of the PC during the ladder

monitoring.

1. Activate the [Program ：Ladder] window

2. Read program memory from the PC by the [PC Transfer]-[Read] command.

You can also write program created at JW-100SP to the program memory of the PC by

the [PC Transfer]-[Write] command.

3. Execute ladder monitor by the [Monitor]-[Start Monitoring] command.

4. In case of changing the circuit → (1) Change circuit (to the following heads)

In case of inserting the circuit → (2) Insert circuit (to the page 8-28)

In case of deleting the circuit → (3) Delete circuit (to the page 8-30)

(1) Change circuit

You can modify the assigned circuit (network). (You can modify several continuous circuits in batch.)

5. Select the line number of the circuit that is to be changed.

6. Click [Monitor]-[Edit Circuit]-[Change].

⇒ The [Edit Circuit (change)] window will be opened, and the selected ladder circuit will be

displayed.

Menu Bar

Main Toolbar

Toolbar for

Editing Ladder

Message Bar

Status Bar

8 ・26


Write the changed circuit to the PC. (same for the button also)

Cancel “Edit Circuit”

The other commands of the menu bar and the function of the toolbar are same as the [Program ：

7. Change the circuit as same as editing the program by the [Program ：Ladder] window.

add

click [Yes], the edited circuit will be written in the PC, and it will turn back to the ladder monitor at

the [Program ：Ladder] window.

8 ・27


(2) Insert circuit

Create a new circuit, and insert it in the assigned position. (You can create several continuous circuits and insert them in batch.)

5. Select the line number of the circuit that is to be inserted. (The circuit that is to be created will

be inserted in front of the selected Line.)

6. Click [Monitor]-[Edit Circuit]-[Insert]

⇒ The [Edit Circuit (Insert)] window will be opened. At this time, the ladder display area is

being cleared out.

Menu Bar

Main Toolbar

Toolbar for

Editing Ladder

Message Bar

Status Bar

Write the modified circuit to the PC. (same for the


button also)

The other commands of the menu bar and the function of the toolbar are same as the

[Program ：Ladder] window, so refer to

Program Edit.

”

8 ・28


7. Modify the circuit as same as editing the program by the [Program ：Ladder] window.

click [Yes], the edited circuit will be written in the PC, and it will turn back to the ladder monitor at

the [Program ：Ladder] window.

8 ・29


(3) Delete circuit

Delete the assigned circuit. (You can modify several continuous circuits in batch.)

5. Select the line number of the circuit that is to be deleted.

6. Click [Monitor]-[Edit Circuit] - [Delete]

⇒ The [Edit Circuit (Delete)] window will be opened, and the selected ladder circuit will be

displayed.

Menu Bar

Main Toolbar

Message Bar

Status Bar

Delete the assigned circuit to the PC. (same for the


button also)

The other commands of the menu bar and the function of the toolbar are same as the

[Program ：Ladder] window, so refer to

8 ・30


you click [Yes], the edited circuit will be deleted from the PC, and it will turn back to the ladder

monitor at the [Program ：Ladder] window.

8 ・31

Chapter 9 Print (Page Setup)

Print

Print the content of the active window. To print, you operate [Page Setup] /[Print]/[Print Preview]/[Print Setup] of the [File] menu.

・Program /System /Parameter ・Data /Symbol

(Details in pages)

9-3

9-22

9-20

9-18

・Data List (program)

(Details in pages)

9-3

9-22

9-20

9-18

・Option Parameter

(Details in pages)

9-3

9-22

9-20

9-18

・Sampling Trace

(Details in pages)

9-22

9-20

9-18

(Details in pages)

9-3

9-22

9-20

9-18

9 ・1


● Outline of "Print Setup"

・Print title ・Print program /system, etc.

Header

Window

（program, etc.）

Footer

Space

Items of setup /operation

Yes /No for the title

Content of the title

Size /position of the title

Yes /No of the header /footer

Content of the header /footer

Size /position of the header

/footer

Printing content of the window

Space

Selection /connection of the printer

Display while printing

Print

Reference items /pages

Page Setup (9 -1)

HF Editor (9 -2)

Page Setup

( [File] menu of HF editor ：page 9-13)

Page Setup (9 -1)

HF Editor (9 -2)

Page Setup

( [File] menu of HF editor ：page 9-13)

Page Setup (9 -1)

Page Setup (9 -1)

Printer Setup (9 -3)

Print Preview (9 -4)

Print (9 -5)

9 ・2


9-1 Page Setup

(Program/System/Data/Symbol/Parameter/Option Parameter/Data List)

Setup the format of the page for printing.

If you click [Page Setup] by the [File] (page 9-1) menu of each window, the dialog box of each setup will be displayed.

If you click [Page Setup] by the [File] menu of [Program : Ladder] window, the [Ladder Print] dialog box will be displayed.

③

①

②

Setup items

Title

Header

Content

If you want to print the title, select "Attach," and if you don't want to print the title, select "None." Assign the file name if you select "Attach." ※

For each page, select "Attach/None" (as explained above) in printing the header.

Assign the file name if you select "Attach." ※

Footer For each page, select "Attach/None" (as explained above) in printing the footer.


Coil Assign whether you want to add or not add the symbol /comment to the coil, and select the printing position (bottom /right) of the comment.

Contact Assign whether you want to add or not add the symbol/comment to the contact.

Zoom In/Out Zoom in or out ladder image to be printed.

・You can select the rate from 50/75/100/150/200%.

Right Character

Position Offset

Specify offset of position of right character such as cross reference or coil comment.

Max. No. of

String

Setup the maximum character numbers when you add symbol/comment to the coil /contact.

The setup area for the symbol is 0 to 16 characters, and for the comment it is 0 to 28 characters.

Cross Reference

Select "Attach/None" in adding the cross reference.

Program Address

Select "Attach/None" in adding the program address.

Margins

Setup spaces of top/bottom/left/right sides.

Boot HF Editor

Start-up "HF Editor" that creates title, header and footer.

※ By clicking [Reference] (number ① above) of each item, you can assign the file name by [Select

File] dialog box (next page) at the title/header/footer.

9 ・3


(Display example)

・Select the file name of title, header and footer.

The operation method is same as "■ Open."

Also the file for title/header/footer is created by clicking [Boot HF Editor] (number ② of the previous page) ( ⇒Refer to "9-2 HF Editor" )

If you click [OK] (number 3 of the previous page) after setting up each item of the [Print Ladder] dialog box, the setup content will be registered.

9 ・4


If you click [Page Setup] by the [File] menu (page 9-1) of program ：mnemonic, the [Print Mnemonic] dialog box will be displayed.

③

①

②

Setup items

Title

Content


Header



Footer

For each page, select "Attach/None" (as explained above) in printing the footer.


Symbol ･Comment Assign whether you want to add or not add the symbol ･comment .

Max. No. of

String

Max. No. of

Columns

Setup the maximum character numbers when you add symbol ･comment .The setup area for the symbol is 0 to 16 characters, and for the comment it is 0 to 28 characters.

Assign the number of columns that are to be printed in one page. If the assigned number of columns can not be printed in a page, it will automatically be printed in the

Margines

Boot HF Editor

Setup spaces of top/bottom/left /right sides.


※ By clicking [Reference] (number ①) of each item, you can assign the file name by

[Select File] dialog box at the title/header/footer.

(Same as the pages 9-3 to 4)

Also, the file for title/header/footer is created by clicking [Boot HF Editor] (number

2 above) ( ⇒Refer to "9-2 HF Editor")

If you click [OK] (number 3 above) after setting up each item, the setup content will be registered.

9 ・5


[3] Setup Page of System

If you click [Page Setup] by the [File] menu (page 9-1) of the system, the [System Print Setup] dialog box will be displayed.

③

①

②

Setup items

Title

Header

Footer

Content






Start address to print

Assign the system memory address that starts the printing.

・It is valid when selecting "None" at comment (described below), or when selecting the "Comment" at comment.

End address to Assign the system memory address that quits the printing.

print ・It is valid when selecting "None" at comment (described below), or when selecting the "Comment" at comment.

Unit to print Select the unit (byte/word/double word) for printing system memory data.

・It is valid only when selecting the "Comment" at comment (described below).

Print format

Comment

Margins

Boot HF Editor

Select the type(binary notation/octal notation/decimal notation/hexadecimal notation/ASCII) for printing system memory data.

Select the "print comment" of the system memory from "None /Comment

/Property Sheet."

・If "None" is selected, the area to print in one page enlarges.

・If "Property Sheet" is selected the content of the property sheet will be printed.




[Select File] dialog box at the title/header/footer. (Same as the pages 9-3 to 4)




9 ・6


[4] Setup Page of Data

If you click [Page Setup] by the [File] menu (page 9-1) of data, the [Data Print setup] dialog box will be displayed.

③

①

②

Setup items

Title

Header

Footer


End address to print

Unit to print

Print format

Content


For each page, select "Attach /None" (as explained above) in printing the header.


For each page, select "Attach /None" (as explained above) in printing the footer.


Assign data memory address that starts the printing.

Assign data memory address that quits the printing.

Select the unit （byte/word/double word ) for printing data of memory data.

・It is valid only when selecting except "None" at comment（described below).

Select the type(binary notation/octal notation/decimal notation/decimal notation

(with +-)/hexadecimal notation/ASCII) for printing data of data memory.

Comment

Margins

Boot HF Editor

Select "symbol/comment print" of data memory from

"None,Symbol,Comment,Symbol/Comment."

Setup spaces of top/bottom /left/right sides.








9 ・7


[5] Setup Page of Symbol

If you click [Page Setup] by the [File] menu (page 9-1) of symbol, the [Symbol Print Setup] dialog box will be displayed.

③

①

②

Setup items

Title

Header

Footer

Content










Unit to print

Unused Address

You cannot set up this item. (The unit is always byte.)

You cannot set up this item.

(Only the address that symbol/comment is registered is printed.)

Comment

Margins

Boot HF Editor

Select the printing of the symbol/comment from "Symbol/Comment, Symbol,

Comment."








9 ・8


[6] Setup Page of Parameter

If you click [Page Setup] by the [File] menu (page 9-1) of the parameter , the [Parameter Print Setup] dialog box will be displayed.

③

①

②

Setup items

Title

Header

Footer

Content


For each page, select"Attach /None" (as explained above) in printing the header.




Start address to print Assign parameter memory address that starts the printing.


Unit to print

Print format

Assign parameter memory address that quits the printing.

The setup of this item is not possible.

Comment

Space

Select the type(binary notation/octal notation/decimal notation/decimal notation

(with +-)/hexadecimal notation/ASCII) for printing data of parameter memory.

Select from "None/Property Sheet."

・If the property sheet is selected, the content of the property sheet will be printed.


Boot HF Editor Start-up "HF Editor" that creates title, header and footer.






9 ・9


[7] Setup Page of Option Parameter

If you click [Page Setup] in the [File] menu (page 9-1) of the option parameter, the [Print Setup] dialog box will be displayed.

③

①

②

Setup items

Title

Header

Footer

Content


For each page, select "Attach /None" (as explained above) in printing the header.






Assign the address of option parameter memory that starts the printing.

Assign the address of option parameter memory that quits the printing.

Unit to print

Print format

Select the module (byte/ word/ double word) for printing data of option parameter memory.

Select the type (binary notation/octal notation/decimal notation/decimal notation

(with +-)/hexadecimal notation/ASCII) for printing data of option parameter.

Comment

Space

Select from "None/Property Sheet."

・If the property sheet is selected, the content of the property sheet will be printed.









9 ・10


[8] Setup Page of Data List

If you click [Page Setup] by the [File] menu (page 9-1) of data list, the [Dat List Print Setup] dialog box will be displayed.

③

①

②

Setup items

Title

Content


Header

Footer









Order Assign the order of the printing. You only can select "In address order."

Unused Address Select either " Print/Not Print" of the address which has not setup symbol ･comment.

Comment Select the printing of the symbol comment."

･comment from "Symbol/comment,symbol,

Margins Setup spaces of top/bottom/left/right sides.








9 ・11

Chapter 9 Print (HF Editor)

9-2 HF Editor

(Program /System/Data/Symbol/Parameter/Other Parameters)

"HF Editor," that edits title/header/footer which are used at the time of printing at the page setup

([File] menu) of each window, is explained.

If you click [Boot HF Editor] by the "setup page dialog box"(pages 9-3 to 11), the [HF Edit] window will be displayed.

(1) (2) (3) (4) (5) (6) (7) ※

(1) (2) (3) (4) (5) (6) (7) ※

・The numbers (1) to (7) are compatible to items that are after this page.

・If you click ※ part, the screen above will change.

9 ・12


(1) [File] menu

Item

New

Open

Save

Save As

Content

Create a new file.

Open the existing file.

・The file extension of the HF Editor is "HFD."

Save the operating file.

・Save without modifying the name /saved place.

Save the operating file with a new name.

・If it was saved without the extension, the "HFD" extension will automatically be added.

・You can save by modifying the name /saved place.

Setup the format of the page for printing by the [Page Setup] dialog box.

Page Setup

Print

Print Preview

Printer Setup

Quit

1 2

・By the setup "1", the print size/print position for JW-100SP printing will be set.

・The setup "2" is useful when you want to confirm the printing image by the HF Editor.

Setting up the JW-100SP is useful for the margin/paper size of the created title

/header/footer by JW-100SP.

Print the content of the active window.

・The [Print] dialog box will be displayed. If you click [OK], the printing starts.

Display the active file as if printing on the screen.

Setup the selection /connection of the printer.

Quit HF Editor.

9 ・13


(2) [Edit] menu

Item

Cut

Copy

Paste

(3) [View] menu

Content

Cut the selected area and saves it.

Copy the selected area and saves it.

Paste the saved data.

Item

Zoom ( ＋)

Zoom ( −)

Toolbar

Content

Enlarge the display.

Contract the display.

Select "yes /no" of the display of the main toolbar.

Drawing Toolbar Select "yes /no" of the display of the drawing toolbar.

Status Bar

Select "yes /no" of the display of the status bar.

・At the status bar, when you select the button of the menu command

/toolbar, a simple explanation of commands and the ON/OFF condition of special keys of the keyboard are displayed.

Main Toolbar

Drawing Toolbar

Status Bar

The function of each button of the main toolbar and the drawing toolbar is the same as the function of the menu bar (File, Edit, View, Select, Help).

9 ・14


(4) [Select] menu

[Assign font]

Assign the character font such as the character line, date and model name in the text box at the [Font] dialog box which is displayed by double clicking inside each box

(quadrangle).

Here, you can assign the font name, style, and size.

Item

Horizontal Line

Vertical Line

Box

Text

Date

Model Name

Address

Network No.

Memory Capacity

Page No.

Grid

Grouping

Reset Grouping

Select

Change Object content

If you drag the mouse after clicking the [Vertical Line], the vertical line will be drawn.

If you drag the mouse after clicking the [Box], the quadrangle will be drawn.

If you drag the mouse after clicking the [Text], the quadrangle which permits the input of character line will be displayed.

If you drag the mouse after clicking the [Date], the quadrangle that displays the date will be displayed.

If you drag the mouse after clicking the [Model Name], the quadrangle that displays the model name will be drawn.

At the editor screen, it is displayed as the "Model," but at the printing, the setup model name will be printed.

If you drag the mouse after clicking the [Address], the quadrangle that displays the address will be drawn.

At the editor screen, it is displayed as the "Address," but at the printing, the front program address of the same page will be printed.

If you drag the mouse after clicking the [Network No.], the quadrangle that displays the network (circuit) number will be drawn.

At the editor screen, it is displayed as the "Network No.," but at the printing, the network number of the same page will be printed.

If you drag the mouse after clicking the [Memory Capacity], the quadrangle that displays the memory volume will be drawn.

At the editor screen, it is displayed as the "Memory Size," but at the printing, the setup memory capacity will be printed.

If you drag the mouse after clicking the [Page No.], the quadrangle that displays the page number will be drawn.

At the editor screen, it is displayed as the "Page No.," but at the printing, the number of the same page will be printed.

Display/Not display the grid. You can setup the space between the grids by the

[ Grid Size] of the [Setup] menu.

Group several selected drawings.

・If you [Grouping] after selecting several drawings, it becomes on group. You can select several drawings by clicking the mouse while keep pressing the [Shift] key.

Return to the previous state of the "Grouping" drawings.

Change the drawing- mode mouse to the drawing-select- mode mouse.

If you click [Change Object] after selecting the object (vertical line /date described above, for example), [Change Object] or [Object Property] dialog box will be displayed, and you can modify the attribute of the object. ⇒ Refer to the next page.

9 ・15


[Change Object]

If you click [Change Object] of the [Select] menu after selecting the object(vertical line /date, for example), the dialog box displayed below will be displayed, and the attribute of the object can be modified.

address/network No./memory capacity)

Item

Line

Position

Size

Content

Assign yes /no (outer line) of the line, kind, and weigh.

Assign the position (X/Ydirection) of the drawing.

Assign the size (width/heigh) of the drawing.

・Setup line (date/page No.)

・The setup content is same as the [Change Object]

the dialog box (described above).

・Setup form (date) ・Setup form (page No.)

Item

Date

Content

Year to day of week

Type of Printing

Print yes/no of the year, month, day, week, and setup each form.

Setup the type of the whole date printing .

Page number

Form

Type of Printing

Setup the form of "print page. ("only the page number" or "add total page number")

Add the assigned character to the page number, and print it. The actual printing image will be displayed as the "Sample."

Page

Default

Value

Setup the default value of the page number from the first page.

Also, if you are printing the title by JW-100SP, the printing starts from the second page with this setup.

If you select "ON" of the check box, "Not Print Less than Page 0," the page number will not be printed when the page number is less than 0.

9 ・16


(5) [Setup] menu

Item Content

Setup the space between the grids by 0.1 mm module.

・The setup is executed at the [Grid Size Setting] dialog box which is displayed by clicking [Grid Size].

Grid Size

(6) [Window] menu

Display example

Item

Overlap Display

Cascade Display

Arrange Icons

Window Name

1, 2 ・・

Content

Display several windows in pile.

Display several windows in line.

Arrange windows that are iconized at the below part of the [HF Edit] window.

The list of the open window will be displayed. Also, a check mark besides the currently active window name will be displayed. Select (click) the window to activate.

(7) [Help] menu

Item

Find Topic

Content

The "help" screen for the HF Editor (Contents/Index) will be displayed.

・If you keep clicking (assigning) the item to find, you can refer to the related help information such as "operation order/ reference of HF Editor."

・To go back to the original screen after referring to the help content, click

Version Data

(HF Edit)

Display the version information of the "HF Editor."

9 ・17

Chapter 9 Print (Print Setup)

9-3 Print Setup

(Main/Program/System/Data/Symbol/Parameter/Option Parameter/Data List/

Sampling Trace)

Setup selection/connection of the printer.

If you click [Printer Setup] of each [File] menu, the [Printer Setup] dialog box will be displayed.

・Main ・Program/System/Parameter

⇒

・Data/Symbol

⇒

・Data List

⇒

・Option Parameter

⇒

・Sampling Trace

⇒

⇒

9 ・18

Chapter 9 Print (Print Setup)

(Display example)

Setup item

Printer

Content

Select the printer from the list of selection box.

Paper Select the paper size and the paper-supplying method from the list of selection box.

Orientation Setup either portrait or land scape.

・If you click [OK] after setting up each item, the setup content will be registered.

9 ・19

Chapter 9 Print (Print Preview)

9-4 Print Preview

(Program/System/Data/Symbol/Parameter/Option Parameter/Data List/

Sampling Trace)

Display the active window as if printing.

If you click [Print Preview] of each [File] menu, the [Print Preview] window will be displayed.

・Program/System/Parameter ・Data/Symbol

⇒

⇒

・Option Parameter

⇒

・Data List

⇒

⇒

・Sampling Trace

⇒

9 ・20

Chapter 9 Print (Print Preview)

Menu bar of the print preview

(Display example of data)

・At the [Print Preview] window, there are options such as "move between pages", "enlarge / contract display," and every printing operations.

⇒ Refer to the next page.

1 2 3 4 5 6 7

Operation item

Move between pages

Content

Enlarge/contract display

If you click [Zoom In](5), the preview image is shown large; if you click [Zoom

Out](6), the preview image is shown small.

If you open the [Print Preview] window, the operating view or the table will be displayed. To display the page after the displaying page, click [Next Page] (2).

To display the page before the displaying page, click [Prev Page] (3).

1 page display /

2 page display

Print

Close

If you open the [Print Preview] window, the printing image of the 1 page will be displayed normally. To display the 2 page, click [Two Page] (4).

To change from the 2 page display to the 1 page display, click [One page].

[One page] is displayed when the 2 page is being displayed.

If you click [Print], the [Print] dialog box will be displayed, and if you click [OK], it starts printing.

If you click [Close] (7), the [Print Preview] window will be closed.

9 ・21

Chapter 9 Print (Print)

9-5 Print

(Program/System/Data/Symbol/Parameter/Option Parameter/Data List

/Sampling Trace)

Print the content of the active window which was formatted by the setup (page 9-3 and after) at the

[Page Setup] of the [File] menu.

If you click [Print] of each [File] menu, the [Print] dialog box will be displayed.

・Program/System/Parameter ・Data/Symbol

⇒

・Option Parameter

⇒

・Sampling Trace

⇒

⇒

・Data List

⇒

9 ・22


(Display example)

・If you click [OK] after setting up the printer (Properties)/Print range/Number of Copies, the starts the printing.

9 ・23


The printing examples of program : ladder, program : mnemonic, data, sampling trace are described below.

(1) Printing example of program : ladder

Header ：Attach (Printing Position：Top Left), Coil：Symbol/Comment (Comment

Position ：BOTTOM),Contact : Symbol/Comment, Cross Reference：Attach,

Program Address ：Attach

9 ・24


(2) Printing example of program ：mnemonic

[Header ：Attach (Printing Position：Top Left), Symbol：Attach, Comment：Attach]

9 ・25


(3) Printing example of data

[Unit to print ：Byte, Print format：Hex, Symbol/Comment：None]

[Unit to print ：Byte, Print format：Binary, Symbol/Comment：None]

[Unit to print ：Byte, Print format：Hex, Symbol/Comment：Attach]

9 ・26

(4) Printing example of sampling trace

(Screen display)


Trigger Mode: Start when the condition is satisfied, Trace Memory File F: 2KB,

Sampling Frequency: Every Scanning, Zoom: 100%, Display in Hex Notation, Cursor Position: 123

9 ・27

SHARP MANUFACTURING SYSTEMS CORPORATION

♦Information about Sharp programmable controller is available at our internet

homepage

http://sharp-world.com/sms/

3.1v 9.2001

Printed in Japan (0.1O.Y.S)

Sharp PC-9800T Instruction manual

Ladder logic programmning software

Model name

Instruction Manual

■ Instruction Manual

Chapter 1 Introduction

Chapter 2 Setup

Chapter 3 Basic operation

Chapter 4 Let’s create program

Chapter 5 Menu operation

Chapter 6 Program edit

Chapter 7 Setup each data

Chapter 8 Monitor

Chapter 9 Print

Table of Contents

Chapter 1 Introduction

Chapter 2 Setup

Chapter 3 Basic operation

Chapter 4 Let's create program ･････････････････････････････････････････ 4･1∼21

Chapter 5 Menu operation

Chapter 6 Program edit

Chapter 7 Setup each data

Chapter 8 Monitor

Chapter 9 Print ････････････････････････････････････････････････････････ 9･1∼27

Chapter 1 Introduction

1-1 Features

1-2 Compatible PC Model

1-3 System Requirements

1-4 Connection between the Personal Computer and the PC

FL-net

1-5 Product Organization

1-6 Caution

1-7 Conventions Used in This Manual

Chapter 3 Basic Operation

3-1 Starting-up and Quitting

3-2

3-3 Screen Configuration

3-4 Kinds of Windows

3-5 Selection of Commands

3-6 Function Summary

Chapter 4 Let's Create Program

4-1 Start-up JW-100SP

4-2 Create Ladder Program

4-3 PC Transfer/////Monitor

4-4 Print

Chapter 5 Menu Operation

5-1 File

5-2 Edit

[1] Find for the First Time

[2] Find Continuously

5-3 Instruction

5-4 Monitor

5-5 Display

Ladder / Toolbar for Editing Mnemonic /Toolbar for Editing Data /

Message Bar

Comment

Decimal Notation /Displays in Decimal Notation (with +-)/Displays in

Hex Notation /Displays in ASCII

5-6 Setup

[1] Function

[2] Operation Content

5-7 PC

[1] I/O Search

[2] Secret

[3] CU Memory Clear

[4] Parity Check

[5] EEPROM

[6] I/O Table Automatic Registration

[1] Error Monitor

[2] Scan Time Monitor

[3] Clock Monitor

5-8 Tool

5-9 Window

5-10 Help

Chapter 6 Program Edit

6-1 Ladder Programming

[1] Direct Input Mode

[2] Dialog Input Mode

[1] Over Write /Insert Mode

[2] Modify Circuit