Electrix RC Boost ECX3100 Instruction manual

boost

1/10 electrIc Buggy

tM

ecX3000 | ecX3000au | ecX3100 | ecX3100au

InstructIon Manual

BedIenungsanleItung

Manuel d’utIlIsatIon

Manuale

Congratulations on your purchase of the Electrix

RC

TM

Boost

TM

Buggy. This 1/10-scale model introduces you to the sport of RC driving.

Herzlichen Glückwunsch zum Kauf des Electrix

RC

TM

Circuit

TM

Stadium Truck. Dieses 1/10 Scale

Model öffnet Ihnen die Welt des RC Car Sports.

Nous vous félicitons pour l’achat du Electrix RC

TM

Circuit

TM

Stadium Truck. Ce modèle 1/10 vous introduit au sport de la conduite RC.

Congratulazioni per l’acquisto di questo RC Circuit

Stadium Truck Electrix. Questa vettura in scala

1/10 vi introdurrà nel mondo dei modelli RC.

EN

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, Inc.

For up-to-date product literature, visit www.horizonhobby.com and click on the support tab for this product.

Meaning of Special Language:

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury

OR create a high probability of superficial injury.

WarnIng: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.

Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. Do not attempt disassembly, use with incompatible components or augment product in any way without the approval of Horizon

Hobby, Inc. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

safety Precautions and Warnings

As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or the property of others.

This model is controlled by a radio signal subject to interference from many sources outside your control. This interference can cause momentary loss of control so it is advisable to always keep a safe distance in all directions around your model, as this margin will help avoid collisions or injury.

Age Recommendation: Not for children under 14 years.

This is not a toy.

•

•

Never operate your model with low transmitter batteries.

Always operate your model in an open area away from cars,

•

•

•

• traffic or people.

Never operate the model in the street or in populated areas for any reason.

Carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable battery packs, etc.) you use.

Keep all chemicals, small parts and anything electrical out of the reach of children.

Moisture causes damage to electronics. Avoid water exposure to all equipment not specifically designed and protected for this purpose.

•

•

•

•

•

•

•

•

•

•

Never lick or place any portion of your model in your mouth as it could cause serious injury.

First-time builders should seek advice from people with building experience to operate the model correctly and meet its performance potential.

Exercise caution when using tools and sharp instruments.

Take care when building, as some parts may have sharp edges.

Immediately after using your model, do NOT touch equipment on the model such as the motor, electronic speed control and battery, because they generate high temperatures. You may burn yourself seriously touching them.

Do not put fingers or any objects inside rotating and moving parts, as this may cause damage or serious injury.

Be sure that your operating frequency is clear before turning on or running your model, and never share the same frequency with somebody else at the same time.

Ensure that others are aware of the operating frequency you are using and when you are using it.

Always turn on your transmitter before you turn on the receiver in the car. Always turn off the receiver before turning your transmitter off.

Keep the wheels of the model off the ground when checking the operation of the radio equipment.

TAbLE Of CONTENTS

Safety Precautions and Warnings ................................................2

Specifications ................................................................................3

Components ..................................................................................3

Vehicle Preparations

Installing Antenna Tube and Body ................................................3

Installing Transmitter Battery ......................................................4

Installing Transmitter Antenna .....................................................4

Charging the Batteries ..................................................................4

Installing Vehicle Battery ..............................................................5

Operation

Transmitter controls ......................................................................6

Getting Started..............................................................................7

When you are Finished .................................................................7

Setting the Gear Mesh..................................................................8

Electronic Speed Control (ESC) .....................................................8

Electrical Layout ............................................................................8

Maintenance .................................................................................9

Shock Cleaning..............................................................................9

Troubleshooting Guide ..................................................................9

Warranty and Repair Policy .........................................................10

Contact Information .....................................................................11

FCC and Compliance Information for the European Union ..........11

Fasteners ......................................................................................42

Parts Diagram...............................................................................43

2 boost

TM

Transmitter

Frequency

Modulation

Battery

Current Consumption

Size

Weight

Servo

Power Supply

Output Torque

Operating Speed

Size

SPECIfICATIONS

27MHz

Pulse Proportional Modulation (PPM)

AA x 8

200mAh

17 x 23.5 x 7.5mm

382 g

4.8V~6V (shared with receiver)

41.66 oz (3 kg-cm)

0.23sec/60 degrees of travel

40.5 x 20 x 36.8mm

Receiver

Frequency

Intermediate Frequency

Current Consumption

Weight

Electronic Speed Control (ESC)

Input Voltage

Electric Capacity (FET)

Electric Capacity (FET)

PWM Frequency

BEC Voltage

Size

Weight

COMPONENTS

1. Electrix RC TM Boost TM 1/10 Buggy

2. Transmitter

3. Antenna Tube (ECX1087)

1 2

27MHz

445kHz

18mAh

15 g

7.2–8.4V

Forward 80 A/240 A

Reverse 60 A/160 A

1kHz

5 V/1 A

27 x 35 x 17.3mm

34 g - 36 g

3

EN

Included Items

4. AA (8)

5. ECX3013 Battery Charger

Note: Charger power outlet

terminals not shown.

6. 7.2V NiMH battery (DYN1050)

7. Alternate Crystal Set (not shown)

4 5

VEhICLE PREPARATIONS

INSTALLING ANTENNA TUbE ANd bOdy

1. Remove the Body Clips (ECX1048).

2. Remove the body.

3. Put the receiver antenna in the antenna tube (ECX1087).

4. Put the antenna tube in the chassis with loose antenna wire extended above the tube.

5. Put the cap on the antenna tube.

6. Put the body and body clips back on the vehicle.

6

boost

TM

3

EN

INSTALLING TRANSMITTER bATTERIES

1. Slide panel open on bottom of transmitter.

2. Obey battery plus (+) and minus (-) diagram in transmitter to install 8 AA batteries.

3. Slide panel closed on transmitter.

CAUTION: ALWAYS use fully charged batteries in the transmitter. Low battery power can result in loss of control of the RC vehicle.

NEVER install damaged batteries, batteries of mixed types or batteries of different ages in the transmitter.

Remove exhausted batteries.

NEVER store transmitter with batteries installed.

Note: Alkaline AA size batteries are recommended.

INSTALLING TRANSMITTER

ANTENNA

1. Put antenna in hole in top of the transmitter.

2. The collapsed antenna will be 2-1/4 inches long when fully inserted.

3. Turn the antenna clockwise until it is tight.

1

Note: Optional AA NiMH battery charger DYN1970 is available.

Use only batteries approved for use with that charger. DYN1970

2300mAh Tx NiMH Conversion Kit: FUT, ECX.

1

2-1/4 in

(57mm)

2

2 3

3

ChARGING ThE bATTERy

a. Attach battery connector to the charger correctly.

B. 7.2V NiMH battery

c. Compatible Battery Charger

note: Charger power outlet terminals not shown

A b

C

bATTERy WARNINGS ANd GUIdELINES

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

•

Read all safety precautions and literature prior to use of this product.

Never allow minors to charge battery packs.

Never attempt to charge dead or damaged batteries.

Never charge a battery if the cable has been pinched or shorted.

Never allow batteries or charger to come into contact with moisture at any time. Never charge batteries in extremely hot or cold places (recommended between 50–80 degrees Fahrenheit or 10–27 degrees Celsius) or place in direct sunlight.

Never leave charging batteries unattended.

Never charge batteries outside recommended levels.

Never charge damaged batteries.

Always charge batteries away from flammable materials.

Always use only NiMH rechargeable batteries. This charger cannot charge batteries such as “heavy duty,” “alkaline battery,” or “mercury battery.”

Always connect the positive red lead (+) and negative black lead (-) terminals of the battery to the charger terminals correctly.

Always disconnect the battery and charger after charging, and let them cool between charges.

Always inspect the battery before charging.

Always terminate all processes and contact Horizon Hobby if the product malfunctions.

Always make sure you know the specifications of the battery to be charged or discharged to ensure it meets the requirements of this charger.

Never connect more than one battery pack to this charger at a time.

Always constantly monitor the temperature of the battery pack while charging.

Always end the charging process if the charger or battery becomes hot to the touch or starts to change form during the charge process.

note: The vehicle battery charger produces 500 milliAmps per hour. Divide the mAh capacity on the label of a battery by 500 to know how long battery charging will require. For example, an 1800mAh battery requires 3.5 hours to charge.

4 boost

TM

INSTALLING VEhICLE bATTERy

1. Turn the thumb nuts to remove the battery strap.

2. Install the battery.

3. Install the battery strap.

4. Turn the thumb nuts to secure the battery strap.

5. Connect the battery.

OPERATION

OPERATING PRECAUTIONS

ANd GUIdELINES

•

•

ALWAYS turn on your transmitter before you turn on the receiver in the car. Always turn off the receiver before turning your transmitter off.

ALWAYS operate vehicle in a wide open area. Operating the vehicle in a small space or indoors can cause overheating at low speeds. Operating at low speed makes heat in the electronic speed control (ESC). Overheating can damage the vehicle and failure may result.

•

•

•

•

•

•

•

ALWAYS keep parts dry.

ALWAYS keep moving parts clean.

ALWAYS use a clear radio frequency

ALWAYS keep vehicle in sight and under control.

NEVER touch moving parts.

NEVER operate vehicle with damaged wiring.

NEVER touch hot parts.

EN

MOTOR CARE

•

•

•

Seat motor brushes by driving smoothly on a flat surface, using the supplied Dynamite 1800mAh battery, during use of the first battery charge.

Prevent overheat conditions to extend motor life.

Excessive motor wear results from:

Frequent turns

Stops and starts

Pushing objects

Driving in deep sand or tall grass

Driving continuously uphill

Over-temperature protection is installed on the ESC to prevent circuit damage, but cannot protect the motor from driving against heavy resistance.

boost

TM

5

EN

TRANSMITTER CONTROLS

reverse sWItch antenna

Pull antenna out to its full length

(ECX1067 Antenna Only)

Allows you to change the direction of steering (ST. REV) and throttle

(TH. REV) controls. (Default settings are “N”) st. d/r aM 27Mhz transMItter crystal

Part # Description

ECX1081 Crystal Set 1 26.995

AM Transmitter Crystal

(Tx)






AM Tx

AM Receiver Crystal

(Rx)

AM Rx

notIce: Paired AM crystals must be replaced to change control frequencies. Do NOT use FM Crystals.

steerIng trIM

Adjusts the amount the front wheels move when turned left or right

(Steering Dual Rate)

PoWer sWItch

Adjust to make the vehicle drive straight with no input at the steering wheel throttle trIM

Adjusts the neutral point of the electronic speed control

Power on or off the transmitter steerIng Wheel

Battery level IndIcator

Good battery power

Low battery power

note: Red light will flash with an audible signal (beep) when batteries are low

Note: Alkaline AA size batteries are recommended.

Note: Optional AA NiMH battery charger DYN1970 is available. Use only batteries approved for use with that charger;

DYN1970 2300mAh Tx NiMH

Conversion Kit: FUT, ECX charger Port

Charge only rechargeable batteries. Non-rechargeable batteries may burst causing injury to persons and/or damage to property .

note: The center pin on the charge jack is positive .

Control steering. Right and

Left steering with ST. REV

Switch on N (See ST. REV switch) throttle trIgger

Reverse

Forward

Stop

Controls power to motor for forward or reverse

6 boost

TM

GETTING STARTEd

1. Fully extend Antenna and Power on Transmitter.

3. Do a Test of Transmitter’s control of vehicle with vehicle wheels off ground.

EN

2. Connect battery to Electronic Speed Control (ESC) and power on the ESC.

4. Start driving slowly and if the vehicle does not go straight, adjust steering trim dial on Transmitter.

WhEN yOU ARE fINIShEd

1. Power off Electronic Speed Control (ESC).

note: Seat motor brushes by driving smoothly on a flat surface during use of the first battery charge.

3. Disconnect Battery.

1

2

2. Power off the Transmitter and Lower Antenna.

4. Remove Battery from vehicle.

note: To prevent damage to antenna, collapse the antenna by pulling the lower sections in first.

boost

TM

7

EN

SETTING ThE GEAR MESh

Gear mesh has already been set at the factory, and setting it is only necessary when changing motors or gears.

note: You must remove the vehicle’s gear cover (a) to do this adjustment.

•

•

•

Precautions

Never touch moving parts.

Never disassemble while batteries installed.

Always let parts cool before touching.

Proper gear mesh (how gear teeth meet) is important to the performance of the vehicle. When gear mesh is too loose, the spur gear could be damaged by the pinion gear of the motor. If the mesh is too tight, speed could be limited and the motor and ESC will overheat.

1. Loosen the two (2) motor screws.

2. Put a small piece of paper between the pinion and spur gears.

3. Push the gears together while tightening the motor screws.

4. Remove the paper and the gears should move a small amount.

5. Reinstall gear cover.

A

ELECTRONIC SPEEd CONTROL (ESC)

note: When motor disconnected or damaged, beep may not be heard.

note: Low voltage cutoff (LVC) will stop the vehicle when the battery gets low. The ESC will reset after approximately 10 seconds.

The vehicle can then be driven slowly back to the driver for battery recharge.

LEd LEd Status description LEd Indication

Solid Green Forward

Solid Red Reverse

Red LEDs flashing with beep beep beep beep beep beep beep beep beep beep beep beep beep beep

Red LEDs flashing twice with beeps beep beep beep beep beep

Red LEDs flashing three times with beeps

Transmitter is not being received.

Signal that Vehicle battery is low.

Motor is overloaded or temperature of

ESC is high.

C

D

E

ELECTRICAL LAyOUT

Part # Description

A

B

ECX1069

ECX1068

ECX1070

Motor

ECX1071 Motor

DYN1050 Battery 7.2V

Steering Servo

Receiver

Battery 7.2V

Electronic Speed Control

(ESC)

A b

C

note: For correct operation, Channels 1 and 2 must be used as shown in wiring diagram. The motor can be disconnected from the ESC at the connectors in the wiring.

AM Receiver Crystal (Rx)

Steering Servo

8 boost

TM

AM Rx

Receiver d

E

Channel 2

Channel 1

MAINTENANCE

ShOCk CLEANING

Rear Shock

•

•

•

•

•

•

•

•

•

Oil-filled shocks will require regular maintenance due to the oil breaking down or getting dirty. This maintenance should be performed after about every 3 to 5 hours of use depending on conditions that the vehicle is used in.

Remove the shock from the vehicle.

Remove the cap from the shock body and dispose of fluid.

Disassemble the shock. Clean thoroughly with DYN5505.

Dry parts before assembly.

Assemble the shock and refill the shock body with silicone fluid (30 weight recommended).

Slowly move the shaft and piston up and down to remove air bubbles.

Move the piston to the midway point of the body and install the cap.

Wipe off any overflowing fluid.

When properly filled, the piston should rebound about

3/8 in (9.5mm) after being pushed in fully.

Install shock on vehicle.

•

ride height adjustment

Ride height is an adjustment that affects the way the vehicle jumps, turns and goes over bumps. Drop one end of the vehicle from approximately 6 inches (150 mm) in height onto a flat surface. When dropping the front of the vehicle, after the vehicle settles make sure the front arms are equal and parallel to the flat surface. Do the same with the rear and look at the rear to make sure both arms are parallel with the flat surface.

Lower the front ride height to increase steering. Lower the rear ride height to increase traction but decrease steering.

REAR ShOCk

ECX1037

ECX1043

ECX1057

ECX1037

ECX1038

ECX3019

ECX1038

ECX1043

ECX1037

ECX3021

ECX3020

ECX3023

ECX3022

ECX1038

Part # Description

ECX3019 Shock Body Set

ECX1037 Shock Caps, Pistons

ECX1038 Shock Parts Set

ECX3020 Front Shock Shaft (2)

Part # Description

ECX3021 Rear Shock Shaft (2)

ECX3022 Front Shock Springs (2)

ECX3023 Rear Shock Springs (2)

ECX1043 Shock O-Ring Set

Problem

Short Run Time

Sluggish Action

Controls Reversed

Motor/ESC overheat

Doesn’t Operate

Poor Range

ECX1037

TROUbLEShOOTING GUIdE

Possible Cause

• Battery damaged/not charged

• Motor dirty or brushes worn

•Motor dirty or brushes worn

• Bind in drivetrain

• Vehicle battery is not charged

• ST. REV or TH. REV

• Over-geared

• Transmitter batteries low

• Transmitter powered off

• ESC powered off

• Vehicle battery is not charged

• Transmitter batteries low

• Transmitter antenna is damaged or loose

• Receiver antenna damaged

• Motor dirty or brushes worn

Solution

• Check/change battery

• Check/clean/replace

• Check/clean/replace

• Clean/adjust

• Replace/recharge

• Change switch position

• Install smaller pinion


• Power On

• Power On



• Check/tighten

• Check/repair/replace

• Check/clean/replace boost

TM

9

EN

EN

WARRANTy ANd REPAIR POLICy

Warranty Period

Exclusive Warranty- Horizon Hobby, Inc., (Horizon) warranties that the Products purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase by the

Purchaser.

Limited Warranty horizon reserves the right to change or modify this warranty without notice and disclaims all other warranties, express or implied.

(a) This warranty is limited to the original Purchaser (“Purchaser”) and is not transferable. REPAIR OR REPLACEMENT AS PROVIDED

UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE

PURCHASER. This warranty covers only those Products purchased from an authorized Horizon dealer. Third party transactions are not covered by this warranty. Proof of purchase is required for all warranty claims.

WARRANTy SERVICES

Questions, assistance, and repairs

Your local hobby store and/or place of purchase cannot provide warranty support or repair. Once assembly, setup or use of the

Product has been started, you must contact Horizon directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please direct your email to productsupport@ horizonhobby.com, or call 877.504.0233 toll free to speak to a

Product Support representative. You may also find information on our website at www.horizonhobby.com.

(b) Limitations- HORIZON MAKES NO WARRANTY OR REPRESEN-

TATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT,

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF

THE PRODUCT. THE PURCHASER ACKNOWLEDGES THAT THEY

ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY

MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.

(c) Purchaser Remedy- Horizon’s sole obligation hereunder shall be that Horizon will, at its option, (i) repair or (ii) replace, any Product determined by Horizon to be defective. In the event of a defect, these are the Purchaser’s exclusive remedies. Horizon reserves the right to inspect any and all equipment involved in a warranty claim. Repair or replacement decisions are at the sole discretion of Horizon. This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or modification of or to any part of the Product.

This warranty does not cover damage due to improper installation, operation, maintenance, or attempted repair by anyone other than

Horizon. Return of any Product by Purchaser must be approved in writing by Horizon before shipment.

Inspection or repairs

If this Product needs to be inspected or repaired, please use the Horizon Online Repair Request submission process found on our website or call Horizon to obtain a Return Merchandise

Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An

Online Repair Request is available at www.horizonhobby.com http://www.horizonhobby.com under the Repairs tab. If you do not have internet access, please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for repair. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours.

When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.

Notice: do not ship batteries to horizon. If you have any issue with a battery, please contact the appropriate horizon

Product Support office.

damage limits

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR

CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION

OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE

PRODUCT, WHETHER SUCH CLAIM IS BASED IN CONTRACT,

WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. Further, in no event shall the liability of Horizon exceed the individual price of the

Product on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury.

By the act of use, setup or assembly, the user accepts all resulting liability.

If you as the Purchaser or user are not prepared to accept the liability associated with the use of this Product, you are advised to return this Product immediately in new and unused condition to the place of purchase.

Law: These Terms are governed by Illinois law (without regard to conflict of law principals).

Warranty Inspection and repairs

To receive warranty service, you must include your original

sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will be repaired or replaced free of charge. Repair or replacement decisions are at the sole discretion of Horizon.

non-Warranty repairs

Should your repair not be covered by warranty the repair will be completed and payment will be required without notification or estimate of the expense unless the expense

exceeds 50% of the retail purchase cost. By submitting the item for repair you are agreeing to payment of the repair without notification. Repair estimates are available upon request. You must include this request with your repair. Non-warranty repair estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashiers checks, as well as Visa, MasterCard, American Express, and

Discover cards. By submitting any item to Horizon for inspection or repair, you are agreeing to Horizon’s Terms and Conditions found on our website under the Repairs tab.

10 boost

TM

Country of Purchase

United States of America

United Kingdom

Germany

France

CONTACT INfORMATION

horizon hobby

Horizon Service Center

(Electronics and engines)

Horizon Product Support

Horizon Hobby Limited

Horizon Technischer

Service

Horizon Hobby SAS

Address

4105 Fieldstone Rd

Champaign, Illinois

61822 USA

Units 1-4 Ployters Rd

Staple Tye, Harlow

Essex CM18 7NS

United Kingdom

Hamburger Str. 10

25335 Elmshorn

Germany

14 Rue Gustave Eiffel

Zone d’Activité du Réveil Matin

91230 Montgeron

Phone Number / Email Address

877-504-0233

Online Repair Request visit: www.horizonhobby.com/repairs

+44 (0) 1279 641 097 [email protected]

+49 4121 46199 66 [email protected]

+33 (0) 1 60 47 44 70 [email protected]

fCC INfORMATION

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

COMPLIANCE INfORMATION fOR ThE EUROPEAN UNION

declaration of conformity

(in accordance with ISO/IEC 17050-1)

No. HH20110212

Product(s):

Item Number(s):

Equipment class:

ECX 1/10th Scale Buggy Boost

ECX3000, ECX3100

1

The object of declaration described above is in conformity with the requirements of the specifications listed below, following the provisions of the European R&TTE directive 1999/5/EC and EMC Directive 2004/108/EC:

EN 300-220

EN 301 489

EN 60950

EN55022

EN55024

EN61000-3-2

EN61000-3-3

Technical requirements for Radio equipment

General EMC requirements for Radio equipment

Safety

Radio disturbance characteristics

Immunity characteristics

Harmonic current emissions

Voltage fluctuations & flicker

EN

Signed for and on behalf of:

Horizon Hobby, Inc.

Champaign, IL USA

Feb 12, 2011

Steven A. Hall

Vice President

International Operations and Risk Management

Horizon Hobby, Inc.

Instructions for disposal of WEEE by users in the European Union

This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment.

The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or where you purchased the product.

boost

TM

11

fASTENERS | bEfESTIGUNGEN |

PIÉCES SERVANT À LA fIxATION | VITERIA

Description | Beschreibung

Description | Descrizione



M3x10mm

TAPPING BINDER HEAD

Linsenkopfschraube

Vis auto-taraudeuse tête

Vite autofilettante testa tonda

M3x12mm

M3x8mm

BINDER HEAD

Linsenkopfschraube

Vis

Vite testa tonda

M3x12mm

TAPPING BINDER HEAD

Linsenkopfschraube



M3x16mm

TAPPING BINDER HEAD

Linsenkopfschraube



M3x18mm

BINDER HEAD

Linsenkopfschraube

Vis

Vite testa tonda

BINDER HEAD

Linsenkopfschraube

Vis

Vite testa tonda

M3x20mm

TAPPING BINDER HEAD

Linsenkopfschraube



M3x10mm

TAPPING FLAT HEAD

Senkkopfschraube

Vis tête plate

Vite autofilettante testa Svasata

M3x12mm

BINDER HEAD

Linsenkopfschraube

Vis

Vite testa tonda

M3x25mm

BUTTON HEAD

M3x30mm

Linsenkopfschraube


Vite testa tonda

M3x06mm

TAPPING FLAT HEAD

Senkkopfschraube

Vis tête plate


M3x15mm

TAPPING FLAT HEAD

Senkkopfschraube



BUTTON HEAD

Linsenkopfschraube

Vis à tête bouton

Vite testa tonda

M3x10mm

TAPPING FLAT HEAD

Senkkopfschraube

Vis auto-taraudeuse à tête bouton


M3x16mm

TAPPING FLAT HEAD

Senkkopfschraube

Vis tête plate




BUTTON HEX

Linsenkopfschraube

Vis hexagonale à tête bouton

Vite testa a brugola

BUTTON HEX

Linsenkopfschraube

Vis hexagonale à tête bouton

Vite testa a brugola

STEP SCREW

Schraube

Vis bridée

Vite a doppio stadio

STEP SCREW

Schraube

Vis bridée


STEP SCREW

Schraube

Vis bridée


SETSCREW

Madenschraube

Vis bridée

Grano

SET SCREW

Madenschraube

Vis bridée

Grano



M3x13mm

SET SHAFT

Schaftschraube

Vis de réglage

Spina filettata

5x7x0.5mm

WASHER

Unterlegscheibe

Rondelle

Rondella

3x8x0.5mm

WASHER

Unterlegscheibe

Rondelle

Rondella

2x7x0.5mm

WASHER

Unterlegscheibe

Rondelle

Rondella

M4

FLANGED LOCK

NUT

Stopmutter

Ecrou de verrouillage à rebord

Dado autobloccante flangiato

M3

LOCK NUT

Senkkopfschraube

Ecrou de verrouillage à rebord

Dado autobloccante

E-CLIP E2.5

LOCK WASHER

42 boost

TM

PARTS dIAGRAM | ExPLOSIONSZEIChNUNG |

VUE ÉCLATÉE dES PIÉCES | ESPLOSO dEL MOdELLO CON REfERENZA PEZZI

RECOMMENdEd ITEMS

Empfohlene Werkzeuge

Outils Recommandés

Attrezzi raccomandati

M3X25

M3X10

M3X10

47

13

47

M4.3X13

3

M4.3X13

2

10

6

7

20

M3X12

14

M3X12

4

6

M4.3X13

6

2

10

8

10

M3X12

17

M3X18

M3X8

M3X12

M2X8

2

M3X12

11

M3X18

M3X18

M3X25

32

M3X12

M3X16

16

32

M3X12

1

20

19

7

M2.5X4

18

31

21

M4.3X13

6

23

31

5

13

22 boost

TM

43

M2.5X4

33

M2.5X8

33

M3X3

42

22 35 35 35

43

35 35

14

M3X18

30

5

12

37 25

M2.5X8

14

34 36

14

36 36 14 34 14

34

36

41 34 38

M2X16

39 36 34

40

34

34

40

36 34 36 34

M2X16

39

44

M3X16

M3X12

M3X20

M3X12

M3X18

37

M3X12

25 M3X12

10

17

12

44

3

32

M3X16

M3X13

M3X12

M3X12

M3X12

19

29

M2.5X4

24

M3X12

M3X12

29

19

20

M2.5X4

27

31

26

28

14

15

21

22

M3X25

M3X10

M3X10

47

47

13

M4.3X13

3

M4.3X13

2

10

6

7

20

M3X12

14

M3X12

4

6

M4.3X13

6

2

10

8

10

M3X12

17

M3X18

M3X8

M3X12

M2X8

2

M3X12

11

M3X18

M3X18

M3X25

32

M3X12

M3X16

16

32

M3X12

1

20

19

7

M2.5X4

18

31

21

M4.3X13

6

23

31

5

13

22

PARTS dIAGRAM | ExPLOSIONSZEIChNUNG |

VUE ÉCLATÉE dES PIÉCES | ESPLOSO dEL MOdELLO CON REfERENZA PEZZI

note: The slipper clutch can be adjusted using this locknut (ECX1060). Fully tighten the locknut.

Then loosen the nut two full turns.

Die Rutschkupplung kann durch diese Stopmutter eingestellt werden (ECX1060). Ziehen Sie die

Mutter an und drehen Sie dann volle zwei Umdrehungen zurück.

5 A noter: Il est possible d’ajuster l’embrayage “patinant” par action sur cet écrou de blocage (ECX1060).

Veillez à serrer l’écrou de blocage

à fond. Ensuite, devissez l’écrou de trois tours complets.

Nota: La frizione può essere regolata con questo dado autobloccante

(ECX1060). Prima avvitate completamente il dado, poi svitatelo 2 giri.

37

M2.5X4

25

33

M2.5X8

M2.5X8

14

34 36

14

39

33

M3X3

42

22 35

36 36

36 34

40

36

34

34

35

14 34 14

35

34

41 34

43

35 35

38

M2X16

40

36 34 36 34

M2X16

39

44

12

M3X16

30 M3X12

14

M3X18

37

M3X12

25 M3X12

M3X20

M3X18 M3X12

17

10

12

44

3

32

M3X16

M3X13

M2.5X4

M3X12

19

29 24

M3X12

29

19

M3X12

M3X12

M3X12

note: When installing wheel, make sure drive hex is aligned with the drive pin. When the drive hex is removed, the drive pin can fall out of the axle.

hinweis: Bitte stellen Sie sicher, dass die Kanäle 1 und 2 wie abgebildet eingesteckt sind. Die

Motorkabel können über Steckverbinder vom Regler getrennt werden.

a noter: Lors de l’installation de la roue, assurez-vous que l’écrou hexagonal est aligné avec la broche de l’axe d’entraînement. En cas de démontage de l’écrou hexagonal, la broche de l’axe d’entraînement peut sortir de l’axe et tomber.

nota: Quando montate le ruote, accertatevi che il trascinatore esagonale sia allineato con la spina del mozzo ruota. Quando togliete il trascinatore esagonale la spina può sfilarsi dal mozzo.

44 boost

TM

14

20

M2.5X4

27

31

15

26

28

21

22

ECX1027

ECX1022

ECX1024

ECX1025

ECX1026

ECX1052

ECX1055

ECX1059

ECX1076

ECX3018

ECX1071

ECX1048

ECX1023

Part # | Nummer

Numéro | Codice

ECX3007

ECX1028

ECX1092

ECX1015

ECX3006

ECX3008

ECX3010

ECX1035

ECX1044

ECX3012

ECX1049

ECX1060

ECX1089

ECX3009

ECX1021

ECX3011

ECX1032

ECX1034

ECX1045

ECX1070

ECX1090

ECX1037

ECX1050

ECX1052

ECX1058

ECX1065

ECX1068

ECX1069

ECX1088

ECX1091

ECX3015

ECX3005

17

18

19

20

21

22

23

24

14

15

16

28

29

30

31

32

25

26

27

12

13

10

11

8

9

6

7

4

5

1

2

3

35

36

33

34

37

40

41

42

38

39

43

44

45

Description Beschreibung Description Descrizione

Main Chassis

Servo Saver Set

Chassis

Servo Saver Set

Châssis principal

Jeu de sauvegarde de servo

Telaio principale

Set salvaservo

Rear Suspension

Mount Set

Setscrew M3x12 (4)

Querlenkerhalter hinten

Motor Screw/Washer

Set

Schrauben Set M3x12 (4)

Motor Screw/Washer Set

Ball Stud (6) Kugelkopf (6)

Shoulder Screw Set (8) Passschrauben Set (8)

Receiver

Servo

Empfänger

Servo

Battery Hold Down Akkuhalter

Front/Rear Bumper Set Stoßstange vorne hinten

Body Mount Set

Mounted Wheel/Tire (2)

Body Mount Set

Front Mounted Wheel/

Tire (2)

Wheel Bearing Set

Rear Mounted Wheel/

Tire (2)

Front Suspension

Arm Set

Radlagersatz Set

Rear Mounted Wheel/Tire (2)

Querlenker Set vorne

Jeu de renfort de suspension arriére

Jeu de vis M3x12 (4)

Vis Moteur/Set Rondelles

Rondelle (6)

Jeu de vis d’épaulement (8)

Récepteur

Servo

Fixation pour batterie

Jeu de pare-chocs avant/arrière

Set Montage Carrosserie

Roue Montée/Pneu (2)

Jeu de roulement de roue


Jeu de bras de suspension avant

Supporti braccetti sosp. posteriori

Grani M3x12 (4)

Viti per il motore/ set di rondelle

Sfere Uniball (6)

Set viti a doppio stadio (8)

Ricevente

Servo

Piastra fermabatteria

Set paraurti ant/post

Set di montaggio per la carrozzeria

Ruote e gomme montate (2)

Set cuscinetti ruote


Braccetti delle sospensioni anteriori

Shock Tower Set

Front Axle (2)

Hinge Pin Set

Camber, Toe Link Set

Wheel Pins (4)

M4 Locknut (4)

Steering Block Set

Rear Suspension

Arm Set

Radmitnehmerstifte (4)

M4 Stopmutter (4)

Lenkhebel Set

Querlenker Set hinten

Ecrou de blocage M4 (4)

Jeu de bloc de direction

Jeu de bras de suspension arrière

Spine trascinatori ruote (4)

Dadi autobloccanti M4 (4)

Fuselli sterzo

Braccetti delle sospensioni posteriori

Transmission Case Set

Driveshaft Set

Getriebegehäuse

Antriebswellen Set

Ensemble carter de transmission Set scatola trasmissione

Ensemble arbre de transmission Set semiassi

Snodi semiassi (4) Driveshaft Pivot Ball (4) Antriebswellengelenk (4)

Rear Axle (2)

Hinge Pin Screws (8)

ESC

Boule pivot d’arbre de transmission (4)

Wellenmitnehmer hinten (2) Axe arrière (2)

Querlenkerbolzen Schrauben (8) Vis de broche d’axe (8)

Regler / ESC CEV

Mozzi ruota anteriori (2)

Viti per perni sospensioni (8)

Variatore elettronico (ESC)

Hub Carrier Set

Shock Caps, Pistons

Hinterer Rad Träger Set

Stoßdmämpferkappen Kolben

Portamozzi posteriori

Set tappi e pistoni ammortizzatori

Gear Cover

Transmission Gear Set

Slipper Clutch Plates,

Pads, Spring

Transmission Idler

Shaft, Drive Pins

Transmission Drive

Shaft (2)

Washer Set

Bearings 10x15x4 (2)

M3 Locknut (4)

Spur Gear

20-Tooth Pinion Gear

Dämpferbrücke

Radachse vorne (2)

Querlenkerbolzen Set

Spur- Sturzstangenset

Gear Cover

Getriebe

Rutschkupplung Teilesatz

Hauptgetriebewelle Set

Getreibeausgangswelle (2)

Unterlegscheiben Set

Lager 10x15x4 (2)

M3 Stopmutter (4)

Hauptzahnrad

20-Tooth Pinion Gear

Jeu de support d’amortisseur

Axe avant (2)

Jeu de broche d’axe

Jeu de biellette de cambrure, de pincement

Broches de roue (4)

Jeu de porte-moyeu arrière

Obturateurs d’amortisseur, pistons

Carter de Réducteur

Ensemble couronne de transmission

Plateaux d’embrayage patinant, plaquettes, ressort

Arbre secondaire de transmission, axes d’entraînement

Axe d’arbre de transmission (2)

Jeu de rondelles

Roulements 10x15x4 (2)

Ecrou de blocage M3 (4)

Couronne

Pignon 10 dents

Supporto ammortizzatori posteriori

Mozzi ruota anteriori (2)

Set perni sospensioni

Set tiranteria Camber e convergenza

Copertura per ingranaggi et ingranaggi trasmissione

Piattelli frizione, disco, molla

Alberino intermedio con spina

Mozzi Differenziale (2)

Set rondelle

Cuscinetti 10x15x4 (2)

Dadi autobloccanti M3 (4)

Corona

Pignone a 20 denti

Motor

Body Clip

Top Shaft/Spacer

Motor

Body Clip

Top Shaft/Spacer

Moteur

Clips Carrosserie

Set de Goupilles

Motore

Clippe per carrozzeria

Set di spessori boost

TM

45

46

47

Part # | Nummer

Numéro | Codice

ECX1033

ECX1029

Description Beschreibung

Setscrew M3x10

Top Plate

Sicherungsschrauben (4)

Chassioberteil

Description

Vis (4)

Plaque frontale

Country of Purchase

United States

United Kingdom

Germany

France

Horizon Hobby

Sales

Horizon Hobby Limited

Horizon Hobby GmbH

Horizon Hobby SAS

Address

4105 Fieldstone Rd

Champaign, Illinois

61822 USA

Units 1-4 Ployters Rd

Staple Tye

Harlow, Essex

CM18 7NS

United Kingdom

Hamburger Str. 10

25335 Elmshorn

Germany

14 Rue Gustave Eiffel

Zone d’Activité du Réveil Matin

91230 Montgeron

Descrizione

Viti (4)

Piastra superiore

Phone Number / Email Address

(800) 338-4639 [email protected]

+44 (0) 1279 641 097 [email protected]

+49 4121 46199 60 [email protected]

+33 (0) 1 60 47 44 70 [email protected]

46 boost

TM

NOTES | hINWEIS | A NOTER | NOTA

boost

TM

47

Created 1/11 28957 © 2011 Horizon Hobby, Inc.

No results