User's manual | Samsung SID-370 User`s manual

High Resolution 37X Zoom Color Dome Camera SID-370 User’s Manual

Thank you for purchasing a SAMSUNG Dome CAMERA.

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.

ENGLISH

Thank you for purchasing a SAMSUNG CCD CAMERA.

Before operating the camera, confirm the camera model and proper input power voltage. In order to that you can understand this manual thoroughly, we'll introduce our model description.

n SID-370 SERIES

• NTSC MODEL

SID-370N

• PAL MODEL

SID-370P n MODEL DESCRIPTION

SIGNAL SYSTEM

• SIGNAL SYSTEM

N → NTSC MODEL

P → PAL MODEL

The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

INFORMATION -This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

WARNING - Changes or modifications not expressly approved by the manufacturer could void the user ’s authority to operate the equipment.

WARNING - To prevent electric shock and risk of fire hazards:

◆ Do NOT use power sources other than that specified.

◆ Do NOT expose this appliance to rain or moisture.

This installation should be made by a qualified service person and should conform to all local codes.

Contents

• Features ………………………………………………………… 5

• Warnings & Cautions ………………………………………… 6

• Precautions …………………………………………………… 7

• Components and Accessories ……………………………… 8

• Overview ………………………………………………………… 9

• Installation ……………………………………………………… 10 n Installation …………………………………………………………… 10 n Adjust the panning and tilting, rotating while watching the monitor ……… 12

• Connection ……………………………………………………… 13 n Connecting Monitor ………………………………………………… 13 n Connecting to Power ………………………………………………… 13 n RS-485 communication control ……………………………………… 14

• Operating Your Camera ……………………………………… 15 n Menu Configuration ………………………………………………… 15 n Menu Setup ………………………………………………………… 16

- WHITE BALANCE ………………………………………………………… 17

- BACK LIGHT ……………………………………………………………… 19

- MOTION DETECTION ……………………………………………………… 21

- FOCUS …………………………………………………………………… 22

- EXPOSURE ……………………………………………………………… 27

- SPECIAL ………………………………………………………………… 32

- RESET …………………………………………………………………… 39

- EXIT …………………………………………………………………… 39

• Troubleshooting ………………………………………………… 39

• Specifications ………………………………………………… 41

• STW Protocol Command Description ……………………… 42

COLOR CCD CAMERA 4 User’s Manual (SID-370)

Features

37x Optical Zoom

The built-in SDZ-370 optical zoom lens is a highly durable component. It features auto focus, auto iris, and zoom functions.

SSNR (Samsung Super Noise

Reduction)

The high performance W-IV DSP chip dramatically reduces the gain noise in digital image precessing, producing clear, sharp images in low lighting environments.

Fine Picture Quality under Ultra Low

Lighting

1/4" high density CCD allows the user to capture bright, high-quality images under ultra low lighting conditions.

High Resolution

Featuring 550TV line horizontal resolution in color mode and 680TV line horizontal resolution in

BW mode, the camera features Sony's 410,000 pixel CCD and captures clean, noiseless, highquality images.

Control via OSD Menu and RS-485

The OSD menu and RS-485 pins allow for remote control of the camera.

The user can also directly control the lens using external control connection.

Day & Night

The camera automatically determines whether it is night time or day time, selecting operating mode automatically. The camera operates in color mode during day light conditions and BW mode in night conditions for clearer identification.

DIS(Digital Image Stabilizer)

The DIS function can compensate for vibration of the camera. so it helps you obtain more stabilized image under the shaking conditions.

Motion Detection

Once motion is detected, the camera sends an alert signal to the processing unit, which, if used in conjunction with an optional alarm, can provide effective surveillance of your property.

3-Axis camera mechanism

The SID-370 is especially incredibly flexible to instal with its 3-axis camera construction,which makes the camera wall or slope mountable.

Miscellaneous Functions

SENS-UP, FLIP(H/V-REV), D-ZOOM, SHARPNESS,

MOTION DETECTION and PRIVACY functions are provided.


Samsung Techwin cares for the environment at all product manufacturing stages to preserve the environment, and is taking a number of steps to provide customers with more environment-friendly products.The Eco mark represents

Samsung Techwin's will to create environment-friendly products, and indicates that the product satisfies the EU RoHS Directive.

Warnings & Cautions

This information is provided to ensure your safety and to prevent any losses, financial or otherwise. Please read it carefully and use the product accordingly.

* For product inquiries, please contact the retail shop where you bought the camera. The use of equipment such as an aerial ladder while providing after-sales service shall be at your expense.

* Separate the power plug when thunder crashes or lighting flashes.

* This product is support equipment for surveillance system. Therefore, we can't compensate for material loss and/or personal injuries by robbery, fire, natural disaster or something like this type.

Warning/Attention/Special Mark Messages

Ignoring this information may result in material loss and/or serious personal injuries including death.

Ignoring this information may result in material loss and/or a slight injuries.

Indicates “Never Allowed.” Indicates “No Disassembling.”

Do not install under extreme temperature conditions.

Precautions

Do not install in high humidity environment.

Use only under temperature conditions between

-10ºC and +50ºC. Provide good ventilation when using in high temperature conditions.

May lower image quality.

Do not install under unstable lighting conditions.

Avoid touching the camera lens.

Severe lighting changes or flickering may hinder normal camera operation.

The lens is the most important component of the camera. Be careful not to smear it with fingerprints.

Do not drop the camera or subject it to physical shock.

Never keep the camera face to strong light directly.


May cause a product malfunction.

May damage the CCD.


Precautions

Do not expose the camera to radioactivity.

1

2

Overview

3

➎ ❼

If it is exposed to radioactivity, For heated CCD, it will be out of order.

Notes

• If the camera is exposed to spotlight or object reflecting strong light, smear or blooming may occur.

• Please check that the power satisfies the normal specification before connecting the camera.

Components and Accessories

❶ 2 3 ❹

➎

1 SID-370 2 Instruction Manual

3 M4 Tapping Screw(4EA) ➍ Installation Video Output Cable

➎ Adapter plate


❻

➍

❿

⓫

⓬

❽

❾

❶ Dome Cover

2 Fixed Bracket

3 Auto Focus 37x ZOOM Lens Module

➍ Fixed Bracket Holder : Holding Fixed Bracket

➎ Rotate Cover : A protective cover for the zoom module; move this cover to optimize the camera's rotation and tilt angles.

6 Rotate Guide : A guide for Rotation Cover.

7 Fixed Bracket Fixation Screw : It fixes the rotation and tilt angle.

8 Function Setup Switch : The detailed description refers to p16.

9 Video Output Terminal to Monitor : Used for monitoring of video output when camera installation.

❿ Video Output Jack

⓫ Power Input Jack

⓬ RS-485 Control Cable : The detailed description refer to p14.


Installation

Installation

1) Separate the dome cover by clockwise rotation.

Unlocking direction

Latch

Locking

Direction

Unlocking direction

[Figure-1]

* To install the dome cover on the camera body, turn the latches in locking direction as shown in the figure 1.

Main Body

(Camera)

Locking

Direction

Dome Cover

Notes

• The installation should be done by qualified service personnel or system installers.

• If the ceiling material is not strong enough to hold the installation screws, the camera may fall off. Reinforce the ceiling as needed.


When installing on a adapter plate

adapter plate

M4 tapping screw (provided)

CAMERA

An arrow for installing directioans

1) Locate the enclosed adapter plate on the desired ceiling area then secure it with the enclosed M4 tapping screws.

2) When attaching the camera to the adapter plate , face the front mark(F) on the bottom of the camera to the installation guide arrow(F) on the adapter plate as shown in [Picture-1) below. Insert the bracket pins into the attaching grooves on the bottom of the camera then turn them clockwise to hold the camera with the adapter plate.

3) Before securing the camera to the adapter plate, pass the power and BNC cables through the adapter plate to the desired location.(To keep the cables sidewise, pass them through the adapter plate into the ceiling.)

4) Once the camera is adjusted and installed on the desired area, turn the dome cover clockwise to secure the camera to the adapter plate.

Locking direction

Bracket pin

Unlocking direction

Dome Cover

Unlocking direction

Locking direction

[Figure-1]

Notes

• Face the installation guide arrow(F) on the adapter plate to the monitoring direction, and then secure the adapter plate with the screws.


Installation

Adjust the panning and tilting, rotating while watching the monitor

Wide Adjust limit position

0˚

83˚

90˚

Fixed Bracket Fixation

Screw

180˚

Tilt Limit Line

1) You can adjust camera to any direction by using Pan, Tilt, Rotate mechanism.

• Adjusting the panning angle by moving the Rotate Cover. Rotate Covers moves by 180 to each side direction and 380 on the whole.

• Adjusting the Tilting angle by moving the Rotate Cover. Rotate Covers moves by 83 angle.

2) Methods of adjustment

• The case of wall installation

1 After mounting the camera on a wall, loosen the Fixed Bracket fixation screws on the camera

2

3 then face the Rotation Cover to the desired monitoring direction.

And the adjust the tilting and panning angle by moving the Rotate Cover.

Once the cover is adjusted to the desired monitoring direction, fasten the Fixed bracket fixation screws on the camera.

• The case of ceiling installation

1 After attaching the camera on a ceiling area, loosen the Fixed Bracket Fixation screws and then adjust the Rotation Cover to the desired monitoring direction.

2 To adjust the tilt angle, refer to the "Notes" in Page 12 and adjust the horizontal angle of the Rotation

Cover not to mask the camera screen.

3 Once the cover is adjusted to the desired monitoring direction, fasten the Fixed Bracket fixation screws.

Notes

• When adjust the tilt angle, keep the Tilt limit line on the Rotation Cover angled or lower than the Wide Adjust limit position on the Rotation Guide(0°~75°). If the angle of the Rotation Cover over the Tilt limit line(76°~83°), the camera screen becomes masked by the dome cover.

(Exception: At 4x Zoom, the camera screen is not masked by the dome cover even if the angle of the Rotation Cover goes over the Tilt limit line.)


Connection

Connecting Monitor

Connect the VIDEO-OUT jack to the VIDEO-IN jack of monitor.

Monitor

CCTV Camera

• As the connecting method varies with the instruments, refer to the manual supplied with the instrument.

• Only connect the cable when the power is turned off.

• Set the 75Ω / Hi-Z selection switch as shown below if you have an intermediate device.

CCTV Camera

Connecting to Power

Connect the adaptor to the power input connector as shown in the figure below. The recommended adaptor specification for SID-370N/P is DC 12V / 500mA.

---- Power Input Terminal

CCTV Camera


Connection

When the resistance value of copper wire is at [20°C(68°F)]

Copper wire size (AWG) #24(0.22mm

2 ) #22(0.33mm

2 ) #20(0.52mm

2 ) #18(0.83mm

2 )

Resistance (Ω/m)

Voltage Drop (V/m)

0.078

0.028

0.050

0.018

0.030

0.011

0.018

0.006

• As shown in the table above, voltage decreases as the wire gets longer. Therefore use of an excessively long adaptor output line for connection to the camera may affect the performance of the camera.

*Standard voltage for camera operation : DC 12V ± 10%

*There may be some deviation in voltage drop depending on the type of wire and the manufacturer.

Notes

• Be sure to connect power only after all the installation is complete.

• Note that DC adaptor is not supplied with camera.

• Ground should be connected to the GND terminal.

RS-485 communication control

Connecting to RS-485 Control Cable

CONTROL CABLE SPEC

WHITE (TRX+) RS-485+

BLACK (TRX-) RS-485-

Using a RS-485 communication, it will be able to control the ZOOM/FOCUS and

OSD menu at the SAMSUNG TECHWIN System Controller or DVR.

(1) The case which it controls from the PC

Using a RS-485 converter, It connects to RS-485 control cable outside camera and serial cable

EX) SERIAL PORT OF THE PC(COM1) — SERIAL CABLE -- RS-485 CONVERTER -- RS-485

CONTROL CABLE


(2)The case which it controls from the DVR or System Controller

It connects the RS-485 control cable in the connection terminal of 485 control boards which are connected with the DVR or System Controller.

485 CONTROL BOARD CONNECTION TERMINAL

(+)CONNECTION TERMINAL

(-)CONNECTION TERMINAL

RS-485 CONTROL CABLE

WHITE (TRX+)

BLACK (TRX-)

Notes

• When you construct external control systems for a camera control, please use to the SAMSUNG TECHWIN PROTOCOL or PELCO-D PROTOCOL.

• When you connecting to RS-485 control cable, please peel off the outer skin inside the RS-485 control cable.

Operating Your Camera

Menu Configuration

WHITE BAL

BACKLIGHT

MOTION DET

FOCUS

EXPOSURE

SPECIAL

RESET

EXIT

Main Setup Menu

• ATW • MANUAL

• OUTDOOR • INDOOR

• OFF

• OFF

• MODE

• D-ZOOM

• LENS INIT • END

• BRIGHTNESS • IRIS

• AGC

• END

• PRIVACY • DAY/NIGHT

• COMM ADJ • IMAGE ADJ

• END

• BLC

• ON

• ZOOM TRK

• AWC->SET

• HLC

• ZOOM SPEED

• ZOOM POS INIT • USER PRESET

• SSNR

• SHUTTER

• SENS-UP

• DIS

• DISPLAY



Menu Setup

✽ Function of Function Setup switch

1. When you press the Function Setup switch for longer than 2 seconds, you could enter menu mode.

2. When you press the Function Setup switch about 1~2 seconds, you could see the massage as following "...Wait AF..." and 10 second later, the auto focus function would operate.

3. When you press the Function Setup switch for less than 1 second, the one-push auto focus function would immediately operate.

4. Moving up and down the Function Setup switch , you could move specific menu or change magnification of the zoom camera.

5. Moving right and left the Function Setup switch, you could select menu or position of the focus.

Function Setup switch

Use the Function Setup switch downward of the lens.

1. Press the Function Setup switch.

• Press the Function Setup switch longer than 2 seconds. on the monitor screen.

Select the function by moving up or down direction of function setup switch.

MAIN SETUP

WHITE BAL ATW

BACKLIGHT OFF

MOTION DET

FOCUS

OFF

EXPOSURE

SPECIAL

RESET

EXIT

Change the status by moving the setup switch left or right.


2. Select the desired feature adjusting the Function Setup switch to up or down.

• Move the arrow indicator to the desired feature item.

3. Change the status of the selected feature adjusting the Function Setup switch to left or Right.

4. When completed, move the arrow indicator to 'EXIT' and press the Function Setup switch.

Notes

• Features marked with a have an accessible submenu.

• Access the submenu by pressing the Function Setup switch.

White Balance (White Bal.)

Use the White Balance function to adjust the screen color.

1. When the SETUP menu screen is displayed, select ’White Bal.‘ by moving up or down direction of Function Setup Switch. so that the arrow indicates ’White Bal.‘ .

2. Select a desired mode moving up or down direction of Function Setup Switch.

MAIN SETUP

WHITE BAL ATW

BACKLIGHT OFF

✽ Select one of the following 5 modes, as appropriate for your purpose.

ATW : Sel ect this when the color temperature is between 1800ºK and 10500ºK

INDOOR : Select this when the color temperature is between 4500ºK and 8500ºK.

OUTDOOR : Sel ect this when the color temperature is between 1800ºK and

10500ºK. (sodium light inclusion)



AWC →SET : To f ind the optimal setting for the current luminance environment in this mode, set the point the camera towards a sheet of white paper and press the

Function Setup Switch. If the environment changes, readjust it.

MANUAL : Select this to fine-tune White Balance manually. Set White Balance first by using the ATW or AWC mode. After that switch to MANUAL mode, fine-tune the White Balance and then press the Function Setup Switch.

WHITE BAL MANUAL SETUP

RED

BLUE

▶

END

117

93

||||||| | ||||||||||||||||||

||||| | ||||||||||||||||||||

Press SET to Return

BACKLIGHT

This camera is designed so that it delivers a distinctive subject and background at

The same time, even when the subject is in backlight, unlike conventional cameras,

By adopting a proprietary W-IV DSP chip.

1. When the SETUP menu screen is displayed, select ‘BACKLIGHT’ by moving up or down direction of Function Setup Switch. so that the arrow indicates ‘BACKLIGHT’.

MAIN SETUP

WHITE BAL ATW

BACKLIGHT OFF

MOTION DET OFF

2. Select a desired mode moving left or right direction of Function Setup Switch. depending on the camera pupose.

BLC : Enables a user to directly select a desired area from a picture, and to view the area more clearly.

HLC(High Light Compensation) : If there is a high light installed in dark environment such as an apartment parking garage or gas station entrance, removing the high light makes it possible to view car license plates efficiently.

HLC MASKING AREA

Notes

• White Balance may not work properly under the following conditions. In this case select the AWC mode.

1 When the color temperature of environment surrounding the subject is out of the control range

2 When the ambient illumination of the subject is dim.

3 If the camera is directed towards a fluorescent light or is installed in a place where illumination changes dramatically, the White Balance operation may become unstable.


<HLC ON>

<HLC OFF>



OFF : Deactivates the BACKLIGHT function.

3. Select a desired mode moving left or right direction of Function Setup Switch. and press the Function

Setup Switch.

• Select ‘BLC’ to adjust the area to be enhanced and enhancement level.

BLC SETUP

▶ LEVEL

TOP

BOTTOM

LEFT

RIGHT

END

LOW

30

||||| | ||||||||||||||||||||

70

30

70

|||||||||||||||||| | |||||||

||||| | ||||||||||||||||||||

|||||||||||||||||| | |||||||

• Select ‘HLC’ to adjust the HLC MASK COLOR and

LEVEL.

HLC SETUP

▶ LEVEL LOW

MASK COLOR 5

END

|||||||||||| | |||||||||||||

Notes

• Since the following symptoms may occur according to the ambient illumination when BLC is selected, set it to OFF.

1 Color or screen changes unnaturally.

2 Noise appears in the bright part of the screen.

• Since the performance of the BLC function may be affected by the area of the bright part of the screen, optimize the installation angle for the best BLC performance.

• If you increase LIMIT, the screen display may be distorted.

• For high performance of BLC function, We recommend that you set IRIS to AUTO in the EXPOSURE setup.

• Activating BLC may cause the camera to repeat the Auto Focus operation depending on lighting conditions. It is recommended that you use the Focus Setup menu in One-Push or Manual mode.

• Smart Zoom and BLC cannot be used in conjunction with each other:

• Setting up BLC and then Smart Zoom automatically cancels BLC.

• Setting up Smart Zoom and then BLC automatically cancels Smart Zoom.


Motion Detection

This product has a feature that allows you to observe movements of objects in 4 different areas on the screen, and the words ‘MOTION DETECTED’ appear on the screen when movement is detected; hence a single individual can conduct supervision efficiently. The camera detects an object’s movement by sensing disparity of outline, and level of brightness and color. The camera receives detection signal from MD output terminal.

MD SETUP

▶ AREA SEL AREA1

AREA MODE ON

SENSITIVITY LOW

SMART ZOOM ON

END

AREA SETUP

▶ TOP 3

BOTTOM 6

LEFT

RIGHT

END

3

6

| |||||||||||||||||||||||||

| | ||||||||||||||||||||||||

| |||||||||||||||||||||||||

| | ||||||||||||||||||||||||

• Please press the Function Setup Switch.

- OFF: MOTION DETECTION mode is cancelled.

- ON: Any motion in the selected areas is observed.

AREA SEL : You can select the area you wish to observe from the 8 area.

AREA MODE : Determines whether to use the MD area selected in SENSITIVITY

SENSITIVITY : You can select up to 8 MD areas. When SENSITIVITY number is high, motion detection sensitivity is increased to recognize even small movement

SMART ZOOM SETUP

▶

START ZOOM X1

TARGET ZOOM X5

DWELL TIME

END

5 SEC

SMART ZOOM : Smart zoom is operated in connection with MOTION DETECTION.

When the SMART ZOOM function is ‘ON’ while the MOTION

DETECTION mode is ‘ON’, the zoom goes to the TARGET ZOOM position once motion is detected. Once the zoom action is finished and ‘DWELL TIME’ has passed, the zoom returns to the ‘START



ZOOM’ position.

• START ZOOM : Moving left or right direction of Function Setup Switch in the ‘START ZOOM’ item to select the zoom position from 1x to 37x to be returned after the ‘SMART

ZOOM’ action is over.

• TARGET ZOOM : Moving left or right direction of Function Setup Switch in the ‘TARGET

ZOOM’ item to select the zoom position from 1x to 37x to be used during

MOTION DETECTION.

• DWELL TIME : Moving left or right direction of Function Setup Switch in the ‘DWELL TIME’ item to select a time between 5 and 60 seconds for the dwell time before the zoom is returned to the ‘START ZOOM’ position. (5,7,10,15,20,30,40,60 sec)

TOP, BOTTOM, LEFT,RIGHT : You can adjust the size of the area

Notes

Tips on Using the Motion Detection Feature

• The feature may not function properly under flickering light conditions.

• The camera interprets sudden changes in lighting and subsequent change in brightness of an object as motion.

• With the feature enabled, other algorithms may require additional time to operate than usual.

Notes

• This system does not guarantee prevention of fire or theft. The manufacturer shall not be held responsible for any accident or damage incurred.

• Connect an external alarm device to MD Out on back of the camera.

FOCUS

MAIN SETUP

WHITE BAL ATW

BACKLIGHT OFF

MOTION DET

FOCUS

OFF

EXPOSURE


1. Press the Function Setup Switch to access the main setup manu and then position the indicator over FOCUS moving up or down direction of Function Setup Switch.

2. Press the Function Setup Switch.

MODE : You can select the most suitable zoom mode. Move the arrow indicator to

’MODE‘ moving up or down direction of Function Setup Switch.

FOCUS SETUP

MODE

ZOOM TRK

ONE-PUSH

AUTO TRACK

ZOOM SPEED

D-ZOOM

FAST

OFF

ZOOM POS INIT AUTO

USER PRESET OFF

LENS INIT

END

MANUAL

• AUTO : Select AUTO and press the Function Setup

Switch to confirm. Increase or decrease optical zoom (ZOOM) or digital zoom (D-ZOOM) positions moving up or down direction of

Function Setup Switch while verifying the changes on screen. Enabling D-ZOOM (ON) means that digital zoom will activate once optical zoom ends. Focus is automatically adjusted with moving zoom.

ZOOM POS SETUP

↑ : TELE ↓ : WIDE

• ONE PUSH : Focus is automatically adjusted just once, after zoom position is changed. Select

'ONE PUSH' and press the Function Setup

Switch to confirm. Increase or decrease

ZOOM/FOCUS POS SETUP optical zoom (ZOOM) or digital zoom

(D-ZOOM) positions moving directional key of Function Setup Switch while verifying the changes on screen. Press the


← : NEAR → : FAR

Function Setup Switch once desired image quality is obtained.



• MANUAL : Select 'MANUAL' and press the Function Setup

Switch to confirm. Increase or decrease optical zoom (ZOOM) or digital zoom (D-ZOOM) positions moving directional key of Function Setup Switch while verifying the changes on screen. Press the

Function Setup Switch on ce desired image quality is obtained. Focus can be manually adjusted, independent of moving zoom.

ZOOM/FOCUS POS SETUP



ZOOM TRK : Select ‘ON’ for the ‘SMART ZOOM’ item in the MOTION DETECTION menu and press Function Setup Switch to change the settings for the ‘SMART ZOOM’ function.

Moving left or right direction of Function Setup Switch in the ‘ZOOM’ item to select ‘AUTOTRACK’ or ‘TRACK’ and press Function Setup Switch to activate the zoom action focus function.

• AUTOTRACK : Zooming in while deciding or adjusting the status of the focus.

• TRACK : Zooming in with no relevance to the focus.

• OFF : Only the zoom lens moves.

FOCUS SETUP

MODE

ZOOM TRK

ONE-PUSH

AUTO TRACK

ZOOM SPEED : Co nfigure zoom tracing speed using this feature. Position the indicator over

'ZOOM SPEED' moving up or down direction of Function Setup Switch and then set to desired mode moving left or right direction of Function Setup Switch.

FOCUS SETUP

MODE

ZOOM TRK

ZOOM SPEED

ONE-PUSH

AUTO TRACK

FAST

• FAST : To move zoom fast.

• MEDIUM : To move zoom at medium speed.

• SLOW : To move zoom slowly.

Notes

• The 'ZOOM SPEED' mode cannot be used if 'MODE' is set to 'AUTO' and 'ZOOM TRK' is 'ON'.


D-ZOOM : Co nfigure magnification limit from x2~x12 using this feature. Position the indicator over 'D-ZOOM' moving up or down direction of Function Setup

Switch. Set 'D-ZOOM' to 'ON' and press the Function Setup Switch to confirm.

FOCUS SETUP

MODE

ZOOM TRK

ZOOM SPEED

D-ZOOM

ONE-PUSH

AUTO TRACK

FAST

OFF

ZOOM POS INIT AUTO

- Set 'ZOOM LIMIT' to the desired level moving left or right direction of Function Setup Switch.

D-ZOOM LIMIT SETUP

▶ LIMIT

END

X2

Notes

• When the DIS is enabled, you cannot use the D-ZOOM.

ZOOM POS INIT: Mo ves to the controlled ZOOM position when the power truned on and is a function of the initial ZOOM position control.

FOCUS SETUP

MODE

ZOOM TRK

ZOOM SPEED

D-ZOOM

ONE-PUSH

AUTO TRACK

FAST

OFF

ZOOM POS INIT AUTO

USER PRESET OFF



- AUTO : If you turn the power off and on, the zoom magnification level is set to the previous level that was set before the power went off.

- MANUAL : The zoom magnification level can be set from 1x to 37x.

Notes

• The zoom postion is saved after 5 seconds when you set zoom function.

USER PRESET

• Prese t user-designated configurations using this feature. Position the indicator over

‘USER PRESET’ moving up or down direction of Function Setup Switch and then set to ‘ON’ moving left or right direction of Function Setup Switch. Press the Function

Setup Switch to confirm.

FOCUS SETUP

MODE

ZOOM TRK

ONE-PUSH

AUTO TRACK

ZOOM SPEED

D-ZOOM

FAST

OFF

ZOOM POS INIT AUTO

USER PRESET OFF

LENS INIT

END

MANUAL

ZOOM/FOCUS POS SETUP



- PRESET NO : Up to 128 preset configuratons are supported.

USER PRESET SETUP

▶ PRESET NO 1

PRESET SAVE

| |||||||||||||||||||||||||

PRESET CLEAR

END

PRESET NOT DEFINED

- PRESET SAVE : Save configured preset.

- PRESET CLEAR : Clear configured preset.

- END : Revert to the FOCUS SETUP menu.

USER PRESET SETUP

PRESET NO 1

▶ PRESET SAVE

PRESET CLEAR

END

| |||||||||||||||||||||||||

PRESET NOT DEFINED


LENS INIT : Moving left or right direction of Function

Setup Switch in the ‘Lens initialization’ item to select ‘Automatic’ or ‘Manual’ and press the SET button to set up the initialization of the lens.

USER PRESET SETUP

PRESET NO 1

PRESET SAVE

▶ PRESET CLEAR

END

| |||||||||||||||||||||||||

PRESET NOT DEFINED

• AUTO : The lens is initialized by setting the date. reset time can be set from 1 day to

7 days and the lens resets every 24 hours from the set time.

• Manual : The Lens will reset when you press the Function Setup Switch.

FOCUS SETUP

MODE

ZOOM TRK

ZOOM SPEED

D-ZOOM

ONE-PUSH

AUTO TRACK

FAST

OFF

ZOOM POS INIT AUTO

USER PRESET OFF

LENS INIT

END

MANUAL

DAY

END

LENS INIT SETUP

1

END : To revert to the main setup menu.

EXPOSURE

MAIN SETUP

WHITE BAL ATW

BACKLIGHT

MOTION DET

FOCUS

OFF

OFF

EXPOSURE

SPECIAL



1. Press the Function Setup Switch to access the main setup menu and then position the indicator over 'EXPOSURE' moving up or down direction of Function Setup

Switch.

2. Press the Function Setup Switch to confirm.

BR IGHTNESS:

Use this feature to adjust image brightness. Position the indicator over 'BRIGHTNESS' moving up or down direction of Function Setup Switch. Then increase or decrease brightness level moving up or down direction of Function Setup Switch while verifying the changes on screen. Set END once desired level is obtained.

EXPOSURE SETUP

BRIGHTNESS 50

|||||||||||| | |||||||||||||

IRIS AUTO

IRIS : Set 'IRIS' to 'AUTO' or 'MANUAL'. Position the indicator over 'IRIS' moving up or down direction of Function Setup Switch and then select the desired iris mode moving left or right direction of Function Setup Switch.

EXPOSURE SETUP

BRIGHTNESS 50 |

|||||||||||||

IRIS

SHUTTER

AUTO

ESC

• AUTO : The iris is automatically activated upon illumination.

• MANUAL : Man ual iris configuration. Set 'IRIS' to 'MANUAL' moving left or right direction of Function Setup Switch and then press the Function Setup

Switch. Increase or decrease iris level moving left or right direction of

Function Setup Switch while verifying the changes on screen.

IRIS MANUAL SETUP

▶ IRIS VAL F1.6

END


SHUTTER : Control image brightness by adjusting shutter speed.

1 Position the indicator over 'SHUTTER' moving up or down direction of Function

Setup Switch. Then select the desired shutter mode (A.FLK, ESC, MANUAL) moving up or down direction of Function Setup Switch.

EXPOSURE SETUP

BRIGHTNESS 50

||||||||||||

|

|||||||||||||

IRIS

SHUTTER

AGC

AUTO

ESC

MEDIUM

• A.FLK (NTSC: 1/100, PAL: 1/120) : Flicker-free mode

• ESC : Automatic shutter speed setting (optimal).

Auto operation is possible only when the IRIS is set to MANUAL.

• MANUAL : Manual shutter speed setting

2 If you choose ’MANUAL‘, select the optimal shutter speed.

• In MANUAL mode, the optimal shutter speed needs to be designated. Select from 1/60 to

1/120,000 (NTSC) or from 1/50 to 1/120,000

(PAL). * 'Sens-Up' mode can be configured manually (2x to 256x).

• Verify changes made to the shutter speed by referencing to changes in on screen brightness.

3 Press the Function Setup Switch to complete.

SHUTTER MANUAL SETUP

▶ SHUTTER VAL 1/60

END

Notes

• Image may become unstable if the camera is set to 'ESC' mode and faces a strong fluorescent light.

• Under 'ESC' mode, the brightness can be adjusted moving left or right direction of

Function Setup Switch.



AGC (Auto Gain Control) : For brighter images.

1 Position the indicator over 'AGC' moving up or down direction of Function Setup Switch.

2 Set 'AGC' to the desired mode moving left or right direction of Function Setup Switch.

• HIGH : Wide range gain value adjustment

• MEDIUM : MEDIUM range gain value adjustment

• LOW : Narrow range gain value adjustment

• MANUAL : Selecting gain value range. (5dB ~ 41dB)

• OFF : Disabled

EXPOSURE SETUP

BRIGHTNESS 50

||||||||||||

|

|||||||||||||

IRIS

SHUTTER

AUTO

ESC

AGC

SSNR

MEDIUM

MEDIUM

GAIN MANUAL SETUP

▶ LEVEL

END

5dB

SSNR(Samsung Super Noise Reduction): On screen noise reduction.

1 Position the indicator over 'SSNR' moving up or down direction of Function Setup Switch.

2 Set 'SSNR' to the desired mode moving left or right direction of Function Setup Switch.

• LOW : Low noise reduction

• MEDIUM : Medium noise reduction

• HIGH : High noise reduction

• OFF : Disabled

EXPOSURE SETUP

BRIGHTNESS 50

| |||||||||||||

IRIS

SHUTTER

AUTO

ESC

AGC

SSNR

SENS-UP

MEDIUM

MEDIUM

OFF


Notes

• Changing 'AGC' setting from LOW to HIGH results in greater sensitivity, as well as on screen noise.

• Setting 'AGC' to OFF locks 'SSNR' configuration.

SENS-UP : Thi s feature ensures clear images at night or under low lighting conditions.

1 Position the indicator over 'SENS-UP' moving up or down direction of Function Setup

Switch.

2 Set 'SENS-UP' to the desired mode moving left or right direction of Function Setup

Switch.

• AUTO : Select this mode for use in night time or under low lighting conditions.

• OFF : Disabled

EXPOSURE SETUP

BRIGHTNESS 50

| |||||||||||||

IRIS

SHUTTER

AGC

SSNR

SENS-UP

AUTO

ESC

MEDIUM

MEDIUM

OFF

Notes

• Once 'AUTO' mode is set, the user can configure Sens-Up limit by increasing / decreasing the shutter speed (e.g.: X2,X4....... X32,X64,X128,X256).

• Enabling Sens-Up increases camera sensitivity and may result in additional noise and/or other phenomenons. This is normal.



SPECIAL

MAIN SETUP

WHITE BAL

BACKLIGHT

ATW

OFF

MOTION DET OFF

FOCUS

EXPOSURE

SPECIAL

RESET

1. Press the Function Setup Switch to access the main setup menu and then position the indicator over 'SPECIAL' moving up or down direction of Function Setup Switch.

2. Press the Function Setup Switch to confirm.

PRIVACY : Hide an area you want to hide on the screen.

DIS

SPECIAL SETUP

PRIVACY

DAY/NIGHT

OFF

AUTO

OFF

1 When the SPECIAL menu screen is displayed, moving up or down direction of Function Setup Switch so that the arrow indicates ‘PRIVACY’.

PRIVACY SETUP

▶

AREA SEL AREA1

AREA MODE ON

MASK COLOR GRAY

MASK TONE 0

END

| |||||||||||||||||||||||||

2 Set up the mode using the 4 direction buttons.

• AREA SEL : You can select up to 8 MD areas.

• AREA MODE : Determines whether to use the area selected in the AREA SEL, and the size and position of the area.

• MASK COLOR : Determine area color. You can select

Gray, Green, Red, Blue, Black, White.

AREA SETUP

▶ TOP 45

BOTTOM 110

LEFT

RIGHT

END

||||| | ||||||||||||||||||||

|||||||||| | |||||||||||||||

20

20

| | ||||||||||||||||||||||||

|||||||||||||||||||||||||

70

||||| | ||||||||||||||||||||


• MASK TONE : Determine the transparency of selected area as controlling number from 0 to 3.

• END : Select this to save the PRIVACY menu settings and return to the

SPECIAL menu.

DAY/NIGHT : You can display pictures in color or black and white.

SPECIAL SETUP

PRIVACY OFF

DAY/NIGHT

DIS

COMM ADJ

AUTO

OFF

1 When the SETUP menu screen is displayed, select ‘DAY/NIGHT’ moving up or down direction of Function Setup Switch so that the arrow indicates 'DAY/NIGHT'.

2 Select a desired mode moving left or right direction of Function Setup Switch according to the picture display you want.

• COLOR : The picture is always displayed in color.

• B/W : The picture is always displayed in black and white.

• AUTO : The m ode is switched to 'Color' in a normal environment, but switches to

'B/W' mode when ambient illumination is low. To set up the sswitching time or speed for AUTO mode, press the Function Setup Switch.

- DWELL TIME : You can select the duration time about changing the day/night mode.

→ 5,7,10,15,20,30,40, 60(sec)

- DURATION : You can select brightness of illumination about changing the day/night mode.

DAY/NIGHT AUTO SETUP

▶

DWELL TIME 5 SEC

DURATION FAST

END

Fast

Slow

Color → B/W

2.5 lux

0.8 lux

B/W → Color

4 lux

6 lux

• EXT : This mode allows you to apply a desired filter to external signals.



Notes

• When using a Video Auto Iris Lens, if you set the lens level to low, automatic switching between Color and Black & White may not occur.

• You cannot control the DAY/NIGHT menu when AGC in the EXPOSURE menu is ‘OFF’.

At this time, the exchange between DAY mode and NIGHT mode operates as like selecting

‘COLOR’ mode.

• The OSD key does not work for 3 seconds when switching to Color or B/W, to ensure stable camera operation.

• The camera may focus less well under infrared illumination than under normal illumination.

• Since the camera may not focus as well under infrared illumination at night as it does under normal illumination, install an Extra-low Dispersion Lens to obtain sharp pictures.

• The brightness of illumination is changeable by installed environment.

DIS : The DIS mode can compensate for vibration of the camera.

SPECIAL SETUP

PRIVACY OFF

DAY/NIGHT

DIS

COMM ADJ

COLOR

OFF

Notes

• When DIS is operating, D-ZOOM does not operate.

COMM ADJ (Communication Adjustment) :

This function sets up the camera communication status when controlling the camera through an external control device.

COMMUNICATION SETUP

▶ PROTOCOL

CAM ID

STW

1

| |||||||||||||||||||||||||

BAUD RATE 9600

UART MODE 8-N-1

TERMINATON OFF

RET PKT DISABLE

END

1 When the SPECIAL menu screen is displayed, moving up or down direction of

Function Setup Switch so that the arrow indicates ‘COMM ADJ’.

2 Set up the mode moving the 4 direction of Function Setup Switch.


• CAM ID

• Protocol

: Determines the camera's identification number

(between 0 and 255).

: Select the communication PROTOCOL. (STW/PELCO-D/PELCO-P/

BOSCH/HONEYWELL/VICON/AD/SEC/PANASONIC)

• BAUD RATE : You can select 2400/4800/9600/19200/38400/57600/115200 bps.

• UART MODE : You can select NONE, EVEN or ODD for the parity bits.

• TERMINATION : Functi on that sets the resistance at the end of RS-485 communications.

✽ Setting Termination Resistance.

In order to prevent signal reduction, the termination resistance of the 2 end units, which are the distant paths for camera and controller to be connected on the RS485 interface, should be connected.

As the termination resistance is built in the camera, whether to make the termination resistance valid or invalid is selected with the TERMINATION.

See the connection diagram for determining to which device the termination resistance will be connected to.

Set up the termination resistance in the dark products.

The installation distance of the product for the termination resistance setting should be less than 1.2 Km. (Maximum cable length is 1.2 Km according to the RS-485 standards.)



• RET PKT : You can choose whether to send an ACK signal when the communication control command is issued to the camera.

Notes

• If Camera is controlled by the Vicon Controller,function button may not work properly.

IMAGE ADJ : Includes image quality or special function factors.

SPECIAL SETUP

PRIVACY OFF

DAY/NIGHT

DIS

SYNC

COLOR

OFF

INT

COMM ADJ

IMAGE ADJ

DISPLAY

1 When the SETUP menu screen is displayed, select ‘IMAGE ADJ.’ by moving up or down direction of Function Setup Switch so that the arrow indicates 'IMAGE ADJ.

2 Select a desired mode moving up or down direction of Function Setup Switch.

• H-REV

• V-REV

: You can flip the picture horizontally on the screen.

: You can flip the picture vertically on the screen.

• SHARPNESS : As you increase this value, the picture outline becomes stronger and clearer.

IMAGE SETUP

▶

H-REV

V-REV

SHARPNESS ON

COLOR

END

OFF

OFF

50

|||||||||||| | |||||||||||

SHARPNESS SETUP

▶ LEVEL

END

16

|||||| | |||||||||||||||||


• COLOR : Adjusting this value affects the chroma level only; the burst level is unaffected.

• END : evert back to the USER PRESET menu.

DISPLAY : Us e this feature to designate a name for the camera, which will display on the monitor screen

SPECIAL SETUP

PRIVACY OFF

DAY/NIGHT

DIS

COLOR

OFF

INT SYNC

COMM ADJ

IMAGE ADJ

DISPLAY

END

CAM TITLE

1 Press the Function Setup Switch to display the main setup menu and move the arrow indicator to ‘CAM TITLE’ moving up or down direction of Function Setup

Switch.

2 Set ‘CAM TITLE’ to ‘ON’ moving left or right direction of Function Setup Switch.

Notes

• If the CAM TITLE feature is set to ‘OFF’, the name will not displayed in the monitor

DISPLAY SETUP

▶

CAM TITLE

CAM ID

CAM INFO

MD ALARM

ZOOM MAG

LANGUAGE

END

OFF

ON

ON

-----

ON

ENGLISH



3 Press Function Setup Switch.

CAMERA TITLE SETUP

ABCDEFGHIJKLM

NOPQRSTUVWXYZ

0 1 2 3 4 5 6 7 8 9 ( )

< >-/#¬S!?,.

←→

CLR POS END

➍ You can enter up to 20 characters.

a. Move the cursor to the character entry field moving left or right direction of

Function Setup Switch.

b. Use the 4 direction of Function Setup Switch to select a desired character.

c. Press the Function Setup Switch to confirm selection of the blinking character. The character is then saved, and the cursor in the entry field moves to the next position.

d. Repeat steps a through c until the desired name has been entered.

Notes

• Correcting Mistakes

Move the cursor th ‘CLR’ and press the Function Setup Switch to clear the entire entry. To modify one character, use LEFT or RIGHT to position the cursor above the character to be modified and click the Function Setup Switch after selecting the character to enter.

➎ Enter a title, move the cursor to ‘POS’ and press the Function Setup Switch. The entered title appears on the screen. Select the position to display the title on the screen by moving the 4 direction of Function

Setup Switch and press the Function Setup Switch.

When the position is determined, select.

FRONT DOOR

• CAM ID

• CAM INFO

: Displays camera ID on top left corner of the screen.

: Displays camera information on screen.

• MOTION ALARM : You can toggle the use of the camera alarm.

• ZOOM MAG : Use th is feature to display the current zoom magnification level on screen. Position the indicator over ‘ZOOM MAG’ moving up


• LANGUAGE

• END or down direction of Function Setup Switch. Then set to ON moving left or right direction of Function Setup Switch.

: You ca n select the menu language according to your requirements (Korean, ESPANOL, FRANCAIS, ITALIANO,

DEUTSCH, ENGLISH, Japanese, Chinese)

: Select this to save the SPECIAL menu settings and return to the

SPECIAL menu.

RESET

To reset your camera to factory default condition.

EXIT

To finish setup menu.

Troubleshooting

If you have trouble operating your camera, refer to the following table.

If the guidelines do not enable you to solve the problem, contact an authorized technician.

• Nothing appears on the screen.

- Check that the power cord and line connection between the camera and monitor are fixed properly.

- Check that you have properly connected VIDEO cable to the camera VIDEO output jack.

• The image on the screen is dim.

- Is lens stained with dirt? Clean your lens with soft, clean cloth.

- Set the monitor to proper condition.

- If the camera is exposed to too strong light, change the camera position.


Troubleshooting

• The image on the screen is dark.

- Adjust the contrast feature of the monitor.

- If you have an intermediate device, set the 75Ω / Hi-z properly.

• The camera is not working properly, and the surface of the camera is hot.

- Check that you have properly connected the camera to an appropriate power source.

• The DAY/NIGHT menu does not work.

- Check that AGC of EXPOSURE SETUP menu is ‘OFF’.

• The SENS-UP function does not work.

- Check that AGC of EXPOSURE SETUP menu is ‘OFF’.

- Check that SHUTTER of EXPOSURE SETUP menu is ‘A.FLK’ or ‘MANUAL’.

• The Motion Detection function does not work.

- Check that MOTION DEF of SPECIAL SETUP menu is ‘OFF’.

• Color is not correct.

- Check the setting of WHITE BAL SETUP menu .

• The screen flickers continually.

- Check that direction of camera turns toward the Sun.

• RS-485 communication fails.

- Check the polarity between RS-485 Control Port and RS-485 cable.

485 Control Board Connection Port RS-485 Control Port

(+) CONNECTION TERMINAL (TRX+)

( - ) CONNECTION TERMINAL (TRX-)

485+

485-

- Check the RS-485 Communication establishment initial value

* RS-485 Communication establishment initial value

Item

Initial value

Camera ID

1

BAUD RATE

9600

UART MODE

8-NONE-1

RET PKT

DISABLE

- We recommend that you make ground connect between camera and controller in order to maintain safety communication control.


Specifications

POWER

CCD

C

I

P

T

S

Sync.

I

C

T

R

A

L

E

L

E

C

Input Voltage

Power Consumption

Size

Total Pixels

Effective Pixels

Optics

Min. Focus Distance

D. ZOOM

Angle Field of view

Scanning System

Synchronization

Frequency

Resolution

Min. Illumination

S/N (Y signal)

Video Output

Focus

Zoom Movement Speed

IRIS Control

Lens Initialize

Camera Title

Camera ID

Day & Night

Gain Control

White Balance

BACK LIGHT

Shutter Speed

O.S.D

Motion Detection

Control Output

SSNR

Privacy Function

FLIP

MIRROR

DIS

PRESET

PROTOCOL

Operating Temperature/Humidity

Storge Temperature/Humidity

Dimension

Weight

SID-370N SID-370P

DC 12V ±10%

2.7 W : Steady-state (at 12V)

4.5 W : Max. (Zoom, Focus, Day&night motor operating, at 12V)

1/4 Inch, Super HAD color CCD

811(H) x 508(V)

768(H) x 494(V)

795(H) x 596(V)

752(H) x 582(V)

37X, f=3.5 to 129.5mm(F1.6 to 3.9)

1500mm

OFF/ON (Limit 12x)

H : Appr. 55.5˚(Wide) to 1.59˚(Tele) V : Appr. 42.5˚(Wide) to 1.19˚(Tele)

2:1 Interlace

Internal

H: 15.734KHz / V: 59.94Hz

H: 15.625KHz / V: 50.00Hz

550 TV Lines(Min.) : Color / 680 TV Lines(Min.) : B/W

0.4 Lux/F1.6(50IRE): Color/0.02 Lux/F1.6(50IRE): B/W

50 dB

CVBS (1.0Vp-p/75Ω)

AUTO/MANUAL/ONE-PUSH

2.5 Sec

AUTO/MANUAL

Built-In

ON/OFF

256EA

AUTO/COLOR/BW/EXT

LOW/MEDIUM/HIGH/MANUAL/OFF

ATW/AWC/MANUAL/INDOOR/OUTDOOR

BLC/HLC/OFF

AUTO/MANUAL/A.FLK

KOREAN,ESPANOL,FRANCAIS,ITALIANO,DEUTSCH,ENGLISH,JAPANESE,

CHINESE : total 8 language

ON/OFF

RS-485 (2400/4800/9600/19200/38400/57600/115200bps)

LOW/MEDIUM/HIGH/OFF

ON/OFF (8 Zones)

ON/OFF

ON/OFF

ON/OFF

128 Positions

STW, PELCO-D, PELCO-P, SEC, PANASONIC, VICON, AD, HONEYWELL, BOSCH

-10˚C to +50˚C / 20% to 80% RH

-20˚C to +60˚C / 20% to 95% RH

(Ø)161 x 124mm

900g

※ This specification can be changed without notice for performance improvement of product.

Note

Max 4.5 ±5% W

(AGC OFF, Weight ON)

Wide to Tele

20 characters

ID:000 ->

Remote only

IR-Cut Filter

Removable

1/120,000sec~X256


STW Protocol Command Description

Command Name

Reset

Focus Far

Focus Near

Zoom Wide

Zoom Tele

ZOOM Direct

AF Stop

One push AF

Command Packet

Return Packet

Byte1

STX

STX

Byte2

CAM ID

Byte3

HOST ADDR

CAM ID HOST ADDR

Checksum

Function Reset all data to factory default value.

Byte4 ll Byte5

CAMMAND

CAMMAND

Byte 6

DATA3

DATA3

Byte7

DATA4

DATA4

Byte8

DATA5

DATA5

Byte9

DATA6

DATA6

Byte10

ETX

ETX

Byte11

CHECKSUM

CHECKSUM

CHECKSUM CALCULATION : UNARY OPERATI ON, OF SUMMATION FROM BYTE2 TO BYTE9. / EX) CHECKSUM = ~(BYTE2+BYTE3+... +BYTE8+ BYTE9);

Command Packet

Return Packet

Function

Command Packet

Return Packet

Function

A0h

A0h

Move focus lens to far direction.

A0h

A0h

CAM ID

CAM ID

CAM ID

CAM ID

HOST ADDR

HOST ADDR

HOST ADDR

HOST ADDR

Move focus lens to near direction.

000Fh

000Fh

0100h

0100h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

AFh

AFh

AFh

AFh

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

Command Packet

Return Packet

Function

Command Packet

Return Packet

Function

A0h

A0h

CAM ID HOST ADDR

CAM ID HOST ADDR

Move zoom lens to wide direction.

A0h CAM ID HOST ADDR


Move wide lens to tele direction.

0200h

0200h

0040h

0040h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

AFh

AFh

AFh

AFh

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

Command Packet

Return Packet

Function

Command Packet

Return Packet

Parameter

Function

Command Packet

Return Packet

Function

Command Packet

Return Packet

A0h

A0h

A0h

A0h

P1, P2: OPTICAL ZOOM = 0000h~06EAh, P3: DIGITAL ZOOM = ((256*10)/Ratio)-1 ex) D-ZOOM 1.1x : P3 = E7h = ((256*10)/ 11)-1, Ratio 11 means 1.1x., D-ZOOM 2.0x : P3 = 7Fh = ((256*10)/20)-1, Ratio 20 means 2.0x.

Stop zoom & focus lens moving.

A0h

A0h

A0h

CAM ID HOST ADDR

CAM ID HOST ADDR

Move ZOOM lens to specific position directly

CAM ID

CAM ID

CAM ID

CAM ID

HOST ADDR

HOST ADDR

HOST ADDR

HOST ADDR

Unconditionally execute auto focus.


CAM ID HOST ADDR

0020h

0020h

00FFh

00FFh

0000h

0000h

0045h

0045h

00h

00h

P1

P1

00h

00h

00h

00h

00h

00h

P2

P2

00h

00h

00h

00h

00h

00h

P3

P3

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

AFh

AFh

AFh

AFh

AFh

AFh

AFh

AFh

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

COLOR CCD CAMERA 42 User’s Manual (SID-370) COLOR CCD CAMERA 43 User’s Manual (SID-370)

STW Protocol Command Description

User Preset Save

User Preset Exec.

User Preset Clear

OSD Menu On/Off

OSD Menu Up

OSD Menu Down

OSD Menu Left

OSD Menu Right

OSD Menu Set

OSD Menu ESC

Function

Command Packet

Return Packet

Parameter

Function

Command Packet

Return Packet

Parameter

Function

Command Packet

Return Packet

Parameter

Function

Command Packet

Return Packet

Parameter

Function

Command Packet

Return Packet

Function

Command Packet

Return Packet

Function

Command Packet

Return Packet

Function

Command Packet

Return Packet

Functio

Command Packet

Return Packet

Function

Command Packet

Return Packet

Save current user preset configuration info rmation.

A0h CAM ID HOST ADDR 0003h

A0h CAM ID HOST ADDR 0003h

P1:00h(USER PRESET 1) ~80h(USER PRES ET 128)

Execute selected user preset.

A0h

A0h

CAM ID

CAM ID

HOST ADDR

HOST ADDR

0007h

0007h


P1

P1

P1

P1

00h

00h

00h

00h

Clear selected user preset.



0005h

0005h

P1

P1

00h

00h


Display OSD menu on the screen. Clear O SD menu and save current menu setup.

A0h

A0h

CAM ID

CAM ID

P1: 00h = ON / 01h = OFF

HOST ADDR

HOST ADDR

00B1h

00B1h

P1

P1

00h

00h

Move OSD arrow to up.

A0h

A0h

CAM ID

CAM ID

HOST ADDR

HOST ADDR

Move OSD arrow to down.



Move OSD arrow to left.

A0h CAM ID

A0h CAM ID

HOST ADDR

HOST ADDR

Move OSD arrow to right.



Move to inside menu

A0h CAM ID

A0h CAM ID

HOST ADDR

HOST ADDR

Move to upper menu.

A0h CAM ID

A0h CAM ID

HOST ADDR

HOST ADDR

0008h

0008h

0010h

0010h

0004h

0004h

0002h

0002h

0100h

0100h

0200h

0200h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h


00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h


00h

00h

Afh

Afh

00h

00h

Afh

Afh

00h

00h

Afh

Afh

00h

00h

Afh

Afh

AFh

AFh

AFh

AFh

AFh

AFh

AFh

AFh

AFh

AFh

AFh

AFh

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

00h

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

CHECK SUM

DECLARATION OF CONFORMITY

Application of Council Directive(s)

Manufacturer's Name

Manufacturer's Address

European Representative Name

European Representative Address

Equipment Type/Environment

Model Name

Beginning Serial NO.

Year of Manufacture

Conformance to

89 / 336 / EEC

SAMSUNG TECHWIN CO., LTD

SAMSUNG TECHWIN CO., LTD

42, SUNGJU-DONG CHANGWON-CITY,

KYUNGNAM, KOREA, 641-716

CCTV Camera

SID-370P

C11S4010007

2009. 4. 1

EN 50081-1 : 1992

EMC-Directive 89/336 EEC and 92/31/EEC

EN 50130-4 : 1996

We, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s).

Manufacturer SAMSUNG TECHWIN CO., LTD

Signature

Full Name

Position

BON JENG GU

QUALITY CONTROL MANAGER

Place

Date

CHANGWON, KOREA

2009. 4. 1

Legal Representative in Europe

Signature

Full Name

Position

Place

Date


MEMO


SALES NETWORK

•

SAMSUNG TECHWIN CO., LTD.

145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si Gyeonggi-do, Korea, 462-703

TEL : +82-31-740-8151~8 FAX : +82-31-740-8145

•

SAMSUNG TECHWIN AMERICA Inc.

1480 Charles Willard St, Carson, CA 90746, UNITED STATES

Tol Free : +1-877-213-1222 FAX : +1-310-632-2195 www.samsungcctvusa.com

www.samsungtechwin.com

www.samsungcctv.com

•

SAMSUNG TECHWIN EUROPE CO., LTD.

Samsung House, 1000 Hillswood Drive, Hillswood Business

Park Chertsey, Surrey, UNITED KINGDOM KT16 OPS

TEL : +44-1932-45-5300 FAX : +44-1932-45-5325

P/No. : Z6806-0983-01A

VAN 09. 04

User's manual | Samsung SID-370 User`s manual

High Resolution 37X Zoom Color Dome Camera SID-370 User’s Manual

Thank you for purchasing a SAMSUNG Dome CAMERA.

Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use.

ENGLISH

Warning/Attention/Special Mark Messages

Installation

When installing on a adapter plate

Adjust the panning and tilting, rotating while watching the monitor

Connecting Monitor

Connecting to Power

RS-485 communication control

Connecting to RS-485 Control Cable

Menu Configuration

Menu Setup

White Balance (White Bal.)

BACKLIGHT

Motion Detection

FOCUS

EXPOSURE

SPECIAL

RESET

EXIT

DECLARATION OF CONFORMITY

Related manuals

D-MAX

DCC-520DV

Divitec

XIN-VCL-0522

Samsung

SDZ-370