Owner's manual | Salter PT-297 Owner`s manual

ENGLISH
PT-297 CINTA DE CORRER MOTORIZADA
MOTORIZED TREADMILL
MANUAL DEL USUARIO
OWNER’S MANUAL
OWNER’S MANUAL V. 1 ENGLISH
PT-297 MOTORIZED TREADMILL
This manual is available at www.salter.es
1
ESPAÑOL
ENGLISH
ENGLISH
1. SAFETY INSTRUCTIONS
WARNING: To reduce the risk of serious injury, read the following safety instructions before using the equipment.
1.
Read all warnings posted on the equipment.
2.
Read this Owner's Manual and follow it carefully before using the equipment. Make sure that it is properly
assembled and tightened before use.
3.
We recommend that two people be available for assembly of this product.
4.
Keep children and pets away from the equipment. Do not allow children and pets to use or play on the equipment.
Always keep children and pets away from the equipment when it is in use.
5.
It is recommended that you place this exercise equipment on an equipment mat.
6.
Set up and operate the equipment on a solid level surface. Do not position the equipment on loose rugs or uneven
surfaces.
7.
Inspect the equipment for worn or loose components prior to each use.
8.
Tighten / replace any loose or worn components prior to using the equipment.
9.
Consult a physician prior to commencing an exercise program. If, at any time during exercise, you feel faint, dizzy,
or experience pain, stop and consult your physician.
10. Follow your physician's recommendations in developing your own personal fitness program.
11. Always choose the workout which best fits your physical strength and flexibility level. Know your limits and train
within them. Always use common sense when exercising.
12. Before using this product, please consult your personal physician for a complete physical examination.
13. Do not wear loose or dangling clothing while using the equipment.
14. Never exercise in bare feet or socks; always wear correct footwear, such as running, walking, or cross-training
shoes.
15. Be careful to maintain your balance while using, mounting, dismounting, or assembling the equipment loss of
balance may result in a fall and serious bodily injury.
16. Keep both feet firmly and securely on the Foot Pedals while exercising.
17. The equipment should not be used by persons weighing over 120 kg.
18. The equipment should be used by only one person at a time.
19. The equipment is for semi-commercial, light-commercial and home usage.
20. Maintenance: Replace the defective components immediately and / or keep the equipment out of use until repair
the equipment completely.
21. Make sure that adequate space is available for access to and passage around the equipment; keep at least a
distance of 1 meter from any obstruction object while using the machine
WARNING: Before starting any exercise or conditioning program you should consult with your personal physician to
see if you require a complete physical exam. This is especially important if you are over the age of 35, have never
exercised before, are pregnant, or suffer from any illness.
OWNER’S MANUAL V. 1 ENGLISH
PT-297 MOTORIZED TREADMILL
This manual is available at www.salter.es
2
ENGLISH
2. MAIN PARTS
Console
Safety Key
Speed Adjustment Switch
Incline Adjustment Switch
Handrail
Running Belt
Wheel
Main Frame
OWNER’S MANUAL V. 1 ENGLISH
PT-297 MOTORIZED TREADMILL
This manual is available at www.salter.es
3
ENGLISH
3. HARDWARE KIT
Nº 74. 3.5 × 12 m/m
Sheet Metal Screw (4)
Nº 100. 5/16" × 18 × 1.5T
Flat washer (6)
Nº 125. M5 × 25m/m
Phillips Head Screw (2)
Nº 44. Safety Key (1)
Nº 103. M6 (66 × 88)
Allen Wrench (1)
OWNER’S MANUAL V. 1 ENGLISH
PT-297 MOTORIZED TREADMILL
This manual is available at www.salter.es
Nº99. 5/16" × 1/2"
Button Head Socket Bolt (14)
Nº 101. 5/16" × 23 × 1.5T
Curved washer (8)
Nº 126. M5 × 35m/m
Phillips Head Screw (2)
Nº 104. Lubricant (1)
Nº 102. Combination M5 Allen Wrench &
Phillips Head Screw Driver (1)
4
ENGLISH
4. ASSEMBLY INSTRUCTIONS
STEP 1
Take out the treadmill from the carton and lay it aside on the smooth ground.
STEP 2
Connect the Computer Cable (Lower)(53) with the Right Upright (4).
4
53
STEP 3
Insert the Uprights (L, R)(5,4) into the Frame Base (2) with the 8pcs of 5/16" ×1/2" Button Head Socket Bolts (99), 4pcs
of 5/16" x 18 x 1.5T Flat Washers (100) and 4pcs of 5/16" × 23 × 1.5T Curved Washers (101) by using the Combination
M5 Allen Wrench & Phillips Head Screw Driver (102).
4
100
99
101
99
5
102
99
101
100
99
2
OWNER’S MANUAL V. 1 ENGLISH
PT-297 MOTORIZED TREADMILL
This manual is available at www.salter.es
5
ENGLISH
STEP 4
Connecting the Computer Cable (Middle) (55) with the Computer Cable (Lower)(53).
55
53
STEP 5
Install the Console Support (6) into the Uprights (L,R) (5,4) with the 6pcs of 5/16" ×1/2" Button Head Socket Bolts (99) ,
2pcs of 5/16" × 18 × 1.5T Flat Washers (100) and 4pcs of 5/16" × 23 × 1.5T Curved Washers (101) by using the
Combination M5 Allen Wrench & Phillips Head Screw Driver (102).
99
101
6
100
99
101
99
101
4
100
99
99
101
99
5
OWNER’S MANUAL V. 1 ENGLISH
PT-297 MOTORIZED TREADMILL
This manual is available at www.salter.es
6
ENGLISH
STEP 6
Install the Outer Handlebar Covers (L & R) (129 & 130) on the Console Support (6) with the 4pcs of 3.5 × 12 m/m Sheet
Metal Screws (74) by using the Combination M5 Allen Wrench & Phillips Head Screw Driver (102) and tighten them.
6
130
129
74
74
74
OWNER’S MANUAL V. 1 ENGLISH
PT-297 MOTORIZED TREADMILL
This manual is available at www.salter.es
7
ENGLISH
STEP 7
Connect the Computer Cable (Middle) (55) with the Computer Cable (21-10). Connect the Connecting Cable (90-7) with
the Connecting Cable (21-9). Connect 5-Pin HR receiver upper cable (21-11) and 5-Pin HR receiver lower cable (90-8).
21-11
21-9
21-10
55
90-8
90-7
STEP 8
Insert the Console Assembly (21) into the Console Support (6). Install the Console Assembly (21) and the Console
Support (6) with the 2pcs of M5×25mm Phillips Head Screws (125) and 2pcs of M5×35mm Phillips Head Screws (126) by
using the Combination M5 Allen Wrench & Phillips Head Screw Driver (102) and tighten them.
21
6
125
126 126
NOTE: Tighten all screw after all components assembly complete.
OWNER’S MANUAL V. 1 ENGLISH
PT-297 MOTORIZED TREADMILL
This manual is available at www.salter.es
8
ENGLISH
5. CONSOLE INSTRUCTIONS
After turning on and put on the safety key, the console will show up welcome greeting then display total running
mileage, hours, program version and then enter ready mode. When total mileage accumulates to 100 km total running
time to 150 hours, the system will show a lubrication prompt. After this prompt is shown two times, the message will
be deleted automatically.
5.1. WINDOW DISPLAYS
TIME：Accumulated running time from 00:00~99:59 or count-down time from 10~99:00.
SPEED： Showing the running speed of the tread belt from 1KM/h(0.6)~16KM/h(10)
DISTANCE：Accumulated running distance from 0.1~99.99KM.
CALORIES：Showing the fat burnt from 0.1~999.9 calories.
INCLINE：Showing 16 incline levels from 0~15.
PULSE：Showing the heart rate value either wearing heart rate monitor stripe or gripping hand pulse sensor, the heart
rate value is displayed in this window.
LAPS： Displaying track with one circle stands for 0.4KM with value from 0~99.
5.2. FUNCTION BUTTONS
START：Press this button, while running, to start the treadmill after displaying 3, 2, 1, GO.
STOP： Press this button to gradually stop the treadmill and end the workout.
FAST： Press this button to increase workout speed. Press once each time increases 0.1KM/h. The increment can be
adjusted between 0.1 and 1while setting the treadmill factor.
SLOW： Press this button to decrease workout speed. Press once each time decreases 0.1KM/h. The increment can be
adjusted between 0.1 and 1 while setting the treadmill factor.
UP：
Press this button while running to increase the incline. Press once each time increases one incline level.
OWNER’S MANUAL V. 1 ENGLISH
PT-297 MOTORIZED TREADMILL
This manual is available at www.salter.es
9
ENGLISH
DOWN：Press this button while running to decrease the incline. Press once each time decreases one incline level.
ENTER：Press this button to enter setting the parameter. While setting, press this button again to accept and enter
next step. Press this button while running to switch the dot matrix window between speed and incline profiles.
FAN： This function is optional. Press this button to the fan on/off.
PROGRAM: Press this button to choose training mode. There are four modes: MANUAL, RANDOM PROGRAM, USER
and HRC (Heart Rate Control).
SELECT：While running RANDOM PROGRAM, you can keep on pressing this button to generate new programs until
there is the program you want.
SPEEDY BUTTON FOR SPEED：There are five speedy buttons for speed: 2KM/h, 4 KM/h, 6 KM/h, 8 KM/h and 10 KM/h
for speedy setting.
SPEEDY BUTTON FOR INCLINE：There are five speedy buttons for incline: 2, 4, 6, 8 and 10 for speedy setting.
Audio Input: This function is optional. It plays the audio signal by the speaker through the internal amplifier.
SAFETY KEY: Put on this key after turning on the power to function the treadmill. Taking off this key automatically shuts
down the treadmill.
5.3. FUNCTION MODES
SPEEDY START. The user initiates the training immediately.
Press START button to speedily start the treadmill after turning on the power and putting on the safety key. Both speed
and incline will be at the lowest value. The user has to adjust them to the desire levels manually using UP/DOWN y
SLOW/FAST buttons.
P0 MANUAL MODE. The user sets an objective parameter.
A. Use PROGRAM button to choose PO MANUAL then press ENTER to set parameters. First is setting weigh. Use
FAST/SLOW buttons to adjust the weigh and press ENTER for next setting.
B. Now the AGE will be displayed. Use FAST/SLOW buttons to select the correct value then press ENTER for next
setting.
C. Choose one of count-down factors TIME, DISTANCE, CALORIES and use SELECT to confirm then press ENTER to set
the value. You can press SELECT to return to select the factor again.
D. Now the selected factor and the value will be displayed. Use FAST/SLOW buttons to select the proper value and
press START to start the treadmill and finish the setting.
E. You can press STOP button to return to the previous step or START to start the treadmill.
RANDOM PROGRAM. This mode which is a profile includes speed and incline automatically generated by the
program. The user can continually choose the profiles until the one which is satisfied. It can also save the USER mode
and make adjustments until a most suitable profile is reached.
A. Use PPROGRAM button to select RANDOM PROGRAM mode and press ENTER to profile selection.
B. Now the dot matrix will display speed profile for 5 seconds then switch to incline profile for another 5 seconds and
recycle. Press ENTER to select the profile and forward to enter next parameter. Press SELECT button to generate
new profile. This step can be continued until ENTER is pressed.
C. Now the value of the weight is displayed. Use FAST/SLOW buttons to adjust the weight and press ENTER for next
setting.
D. Now the value of the age will be displayed. Use FAST/SLOW buttons to adjust the age and press ENTER for next
setting.
E. Now the preset time 20:00 will be displayed. Use FAST/SLOW buttons to adjust for proper time duration and press
START to start the treadmill.
F. The profile can be saved as an USER profile when the workout is finished. The USER can be adjusted whenever is
necessary.
OWNER’S MANUAL V. 1 ENGLISH
PT-297 MOTORIZED TREADMILL
This manual is available at www.salter.es
10
ENGLISH
USER MODE. This mode provides five personal profiles.
A.
B.
C.
D.
E.
F.
Use PROGRAM to select the USER mode. Use UP/DOWM buttons to switch the user names. Use NAME to enter
the user name with FAST/SLOW buttons to enter characters A~Z. There are no more than 7 characters to enter.
Press STOP after entering the last character and exit.
Now the value of the weight is displayed. Use FAST/SLOW buttons to adjust the weight and press ENTER for next
setting.
Now the value of the age will be displayed. Use FAST/SLOW buttons to adjust the age and press ENTER for next
setting.
Now the preset time 30:00 will be displayed. Use FAST/SLOW buttons to adjust for proper time duration and press
ENTER to set profile.
Now the dot matrix window will display the SPEED blinking the first row. Use FAST/SLOW buttons to adjust and
press ENTER for next segment. There are 20 segments in a profile. The segment will blink while setting. After
finishing 20 segments, press ENTER to set incline profile.
Now the dot matrix window will display the incline blinking the first row. Use FAST/SLOW buttons to adjust and
press ENTER for next segment. There are 20 segments in a profile. The segment will blink while setting. After
finishing 20 segments, press START to begin the workout.
HRC (HEART RATE CONTROL MODE). The user preset a heart rate target and the program automatically adjusts the
profile speed and inclination.
Wearing HR stripe is recommended to use this mode.. If it is not installed, the user will grab the hand pulse sensor
throughout this mode. The program will ask for heart rate value when hands are released from the sensor. When there
is no heart rate value for a certain of time, the program stops.
There are two modes for HRC program:
1.
2.
HRC1 adjusts the speed to keep the heart rate at the target value.
HRC2 adjusts the incline to keep the heart rate at the target value.
A.
Use PROGRAM to select HRC program. Press ENTER button to enter this mode and use SELECT button to switch
between two modes. Press ENTER button to set parameters.
Now the value of the weight is displayed. Use FAST/SLOW buttons to adjust the weight and press ENTER for next
setting.
Now the preset time 30:00 will be displayed. Use FAST/SLOW buttons to adjust for proper time duration and press
ENTER to set next parameter.
Now the value of the age will be displayed. Use FAST/SLOW buttons to adjust the age and press ENTER for next
setting.
To change the target heart rate value, the target heart rate value will be in the range of 55%~85% value calculated
by the program according to the age you have entered. You can increase or decrease the target value as what fits
you. Consulting your physician to determine the proper value before setting is recommended. Press START to
begin your workout.
B.
C.
D.
E.
OWNER’S MANUAL V. 1 ENGLISH
PT-297 MOTORIZED TREADMILL
This manual is available at www.salter.es
11
ENGLISH
6. ADJUSTMENTS
UNFOLDING
Pull locking knob and hold running deck and lower down to the floor.
(As shown Figure 1_2.)
FOLDING
Pull the locking knob with right hand, left hand lift the running deck up to 30cm then two hands lift it until it is
locked by the locking knob. (As shown in Figure 3_4)
TRANSPORT
Before moving the treadmill, convert the treadmill to the storage as described above. Make sure that the Locking
Knob is closer fully over the frame guide.
1).Hold the upper ends of the handrails. Place one foot on the base.
2).Tilt the treadmill back until it rolls freely on the rear wheels. Carefully move the treadmill to the
desired location. To reduce the risk of injury, use extreme caution while moving the treading. Do not
attempt to move the treadmill over an uneven surface.
3).Place one foot on the base, and carefully lower the treadmill until it is resting in the storage position.
1
2
4
OWNER’S MANUAL V. 1 ENGLISH
PT-297 MOTORIZED TREADMILL
This manual is available at www.salter.es
3
12
ENGLISH
BELT ALIGNMENT
If during use you notice that walking belt either shifts to the right or the left of center, first remove "Safety Key" and
unplug equipment from AC power source. Using M6 Allen wrench provided, turn left rear roller adjustment as
indicated below clockwise no more the 1/4" of a turn. Remove M6 Allen wrench, insert "Safety Key" and insert AC
power cord into AC outlet. Turn on your treadmill and observe after running a few minutes to see if problem has been
corrected. This may take several adjustments, so repeat the above procedure.
TREADMILL LUBRICATION
When total mileage accumulates to 100 km total running time to 150 hours, the system will show a lubrication prompt.
After this prompt is shown two times, the message will be deleted automatically.
It is important to lubricate periodically the treadmill.
WHEN YOU SHOULD LUBRICATE THE BELT?
1. After the first 25 hours of use (2-3 months).
2. Every 50 hours of use (5-8 months).
HOW TO CHECK TREADBELT FOR PROPER LUBRICATION?
Lift one side of the treadbelt and feel the top surface of the
treadboard.
If the surface is slick to the touch, then no further lubrication is
required.
If the surface is dry to the touch, apply one packet of lubricant or half
of the bottle of lubricant.
HOW TO APPLY LUBRICANT?
1. Lift one side of treadbelt.
2. Pour one half of the lubricant bottle under the center of the treadbelt on the top surface of the treadboard.
3. Walk on the treadmill at a slow speed for 3 to 5 minutes to evenly distribute lubricant.
NOTE: DO NOT over lubricate treadboard. Any excess lubricant that comes out should be wiped off.
NOTE: DO NOT over lubricate treadboard. Any excess lubricant that comes out should be wiped off.
OWNER’S MANUAL V. 1 ENGLISH
PT-297 MOTORIZED TREADMILL
This manual is available at www.salter.es
13
ENGLISH
7. MAINTENANCE
The maintenance of the equipment is easy:
•
Dry and clean those areas exposed to perspiration, especially the console. It is recommended to use towels in order
to avoid the sweat falling to the equipment.
•
Dust and dirt may be the cause of functioning problems in the gears and the internal bearings. It is recommended
keeping the equipment casing and its different elements clean.
¡ATTENTION!
Error message “LOST SPEED” : The signal of RPM speed has been lost. Check the imbedded magnet in front roller and
the sensor together with the proper connection of the cable.
OWNER’S MANUAL V. 1 ENGLISH
PT-297 MOTORIZED TREADMILL
This manual is available at www.salter.es
14
ENGLISH
8. PARTS LIST
Nº
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
16~3
17
18
19
20
21
21~1
21~2
21~3
21~6
21~7
21~9
21~10
21~12
21~13
21~14
21~16
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
Description
Main Frame
Frame Base
Incline Bracket
Right Upright
Left Upright
Console Support
Outer Slide
Inner Slide
Locking Knob
Incline Motor
Drive Belt
Motor Bracket
Motor
Running Belt
Running Deck
Front Roller W/Pulley
Magnet
Rear Roller
Deck Cross Brace
Wheel Sleeve
Rear Wheel Sleeve
Console Assembly
Console Top Cover
Console Bottom Cover
Top Book Rack
Fan
2.5 × 32m/m_Sheet Metal Screw
350m/m_Connecting Cable
350m/m_Computer Cable (Upper)
Amplifier Controller (Optional)
Amplifier Cable (Optional)
300m/m_Computer Cable
200m/m_Ground Wire
Console Locking Tube
Frame Base Cover (L)
Frame Base Cover (R)
Motor Top Cover
Rear Adjustment Base (L )
Rear Adjustment Base (R )
Speed/Hand Pulse Complex
Incline/Hand Pulse Complex
Breaker
On/Off Switch
Frame Base End Cap
Frame Base Front Wheel
Frame Base Rear Wheel
Cushion
Handgrip Foam
Foot Rail
Non-Slip Rubber
OWNER’S MANUAL V. 1 ENGLISH
PT-297 MOTORIZED TREADMILL
This manual is available at www.salter.es
Quantity
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
4
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
2
2
6
2
2
2
15
ENGLISH
Nº
Description
40
41
42
43
44
Motor Cover Anchor
□21.4 × 21.4m/m_Square End Cap
□25.4 × 25.4m/m_Square End Cap
□30 × 60m/m_Square End Cap
800m/m_Safety Key
5
1
1
2
1
45
46
47
48
49
50
51
52
53
55
56
58
59
60
61
62
63
64
65
66
67
68
69
70
71
Power Socket
3/8" × 7T_Nut
Sensor Rack
Power Cord
150m/m_Connecting Wire (White)
150m/m_Connecting Wire (Black)
10cm × 764 × 764_Connecting Wire (Black)
Controller
2100m/m_Computer Cable (Lower)
700m/m_Computer Cable (Middle)
1000m/m_Sensor W/Cable
1/2" × 1"_Hex Head Bolt
3/8" × 92m/m_Button Head Socket Bolt
3/8" × 1-3/4"_Hex Head Bolt
3/8" × 1-1/2"_Hex Head Bolt
3/8" × 3/4"_Hex Head Bolt
M8 × 60m/m_Hex Head Bolt
M8 × 12 m/m_Hex Head Bolt
5/16" × 1"_Button Head Socket Bolt
3/8" × 4-1/2"_Socket Head Cap Bolt
3/8" × 2"_Flat Head Socket Bolt
1/2" × 1-1/4"_Carriage Bolt
M8 × 80m/m_Socket Head Cap Bolt
M8 × 25m/m_Flat Head Countersink Bolt
Motor Bottom Cover
5 × 16m/m_Tapping Screw
3.5 × 12 m/m_Sheet Metal Screw
1/2" × 8T_Nyloc Nut
3/8" × 7T_Nyloc Nut
5/16" × 7T_Nyloc Nut
M8 × 8T_Nyloc Nut
3/8" × 2T_Split Washer
M8 × 1.5T_Split Washer
M5_Split Washer
3/8" × 19 × 1.5T_Flat Washer
3/8" × 25 × 2T_Flat Washer
5 × 13 × 1.0T_Flat Washer
Ø50 × Ø13 × 3T_Nylon Washer
Ø10 × Ø25 × 3T_Nylon Washer
Ø6.5 × Ø25 × 1.5T_Concave Washer
M5_Star Washer
5 × 2T_Speed Nut Clip
Beverage Holder Assembly
Beverage Holder
300m/m_Safety Switch Module W/Cable
1
3
1
1
1
1
1
1
1
1
1
2
1
1
2
4
1
2
2
1
4
2
2
6
1
13
28
4
6
2
1
6
2
3
6
4
10
4
3
8
3
2
1
1
1
3 × 10m/m_Sheet Metal Screw
2
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
90~1
90~3
90~5
OWNER’S MANUAL V. 1 ENGLISH
PT-297 MOTORIZED TREADMILL
This manual is available at www.salter.es
Quantity
16
ENGLISH
Nº
90~7
90~8
91
92
93
95
96
99
100
101
102
103
104
105
106
111
112
113
114
114~2
114~3
114~4
115
115~2
115~3
115~4
116
125
126
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
147
148
149
150
Description
150m/m_Computer Cable
150m/m_Computer Cable
4 × 12m/m_Sheet Metal Screw
Belt Guide
5 × 16m/m_Tapping Screw
Cylinder
M8 × 50m/m_Flat Head Countersink Bolt
5/16" × 1/2"_Button Head Socket Bolt
5/16" × 18 × 1.5T_Flat Washer
5/16" × 23 × 1.5T_Curved Washer
Combination M5 Allen Wrench & Phillips Head Screw Driver
M6 (66 × 88)_Allen Wrench
Lubricant
Adjustable Foot Pad
Beverage Holder Cover
3.5 × 16m/m_Tapping Screw
Wire Tie Mount
Top Motor Cover Plate
Console Speaker Cover (L)
Speaker W/Cable (L) (Optional)
Speaker Grill Anchor (Optional)
3 × 10m/m_Sheet Metal Screw (Optional)
Console Speaker Cover (R)
Speaker W/Cable (R) (Optional)
Speaker Grill Anchor (Optional)
3 × 10m/m_Sheet Metal Screw (Optional)
3 × 10 m/m_Sheet Metal Screw
M5 × 25m/m_Phillips Head Screw
M5 × 35m/m_Phillips Head Screw
M5 × 12m/m_Phillips Head Screw
Outer Handlebar Cover (L)
Outer Handlebar Cover (R)
Bottom Inner Handlebar Cover (R)
Bottom Inner Handlebar Cover (L)
Top Inner Handlebar Cover (L)
Top Inner Handlebar Cover (R)
3 × 75m/m_Sheet Metal Screw
Handgrip End Cap
Choke
Filter
400m/m_Connecting Cable Of Motor
4 × 19m/m_Sheet Metal Screw
Chest Strap (Optional)
200m/m_Connecting Wire (White)
Receiver, HR (Optional)
1000m/m_Connecting Cable (Lower)
300m/m_Ground Wire
Copper Foil
Audio Cable (Optional)
Drink Bottle (Optional)
OWNER’S MANUAL V. 1 ENGLISH
PT-297 MOTORIZED TREADMILL
This manual is available at www.salter.es
Quantity
1
1
12
2
30
1
2
14
6
8
1
1
1
2
1
5
5
1
1
1
3
3
1
1
3
3
2
2
2
7
1
1
1
1
1
1
2
2
1
1
1
4
1
1
1
1
1
1
1
1
17
ENGLISH
OWNER’S MANUAL V. 1 ENGLISH
PT-297 MOTORIZED TREADMILL
This manual is available at www.salter.es
18
ENGLISH
9. ENVIRONMENTAL NOTE
The symbol with which is marked this unit (waste bin with wheels) indicates that it cannot be thrown
for any reason to the domestic waste. When disposing of the product should be taken to a proper
recycling point.
If properly dispose of the product may be reused and recycled, and it will help to conserve natural
resources, preserve the environment and significally reduce the potential negative impact on our
environment.
For more information about the return system, collection and recycling of these products contact your City Council or
the retailer.
REF. PT- 297
MOTORIZED TREADMILL
SALTER Design and quality
Made in: TAIWAN
Imported by Cial. SALTER, S.A.
Lluis Millet, 52
08950 Esplugues de Llobregat
Barcelona – Spain
N.I.F.: A-08544298
OWNER’S MANUAL V. 1 ENGLISH
PT-297 MOTORIZED TREADMILL
This manual is available at www.salter.es
19