Bernina 135 S Sewing Machine User Manual

BenQ RS232 Code
Model: SP870
1. Connection :
The below shows the illustration of connection between control terminal and projector.
WIRE RUN LIST
CONN1
COLOR
CONN2
3
BLACK
1
7
BROWN
2
4
RED
3
5
ORANGE
4
8
YELLOW
5
1
GREEN
6
2
BLUE
7
9
WHITE
8
Shell
SHIELD
Shell
<Pin assignment: CONN1>
Pin
Description
Pin
Description
1
NC
2
RXD
3
TXD
4
NC
5
GND
6
NC
7
RTS
8
CTS
9
NC
1
2
6
3
7
4
8
5
9
<Pin assignment: CONN2>
Pin
Description
Pin
Description
1
RX
2
CTS
3
NC
4
GND
5
RTS
6
NC
7
TX
8
GND
8
7
5
6
4
2
3
1
‹
‹
Make sure that your computer and projector are turned off before connection.
Power on the computer first, and then plug the power cord of the projector.
(It may cause Com port incorrect function, if you do not follow this instruction)
‹
Adapters may be necessary depending on the PC connected to this projector. Please contact with
your dealer for further details.
2. Interface Setting :
Baud Rate
115200 bps
Data Length
8 bit
Parity Check
None
Stop Bit
1 bit
Flow Control
None
3. RS232 Commands
Function
Type
Operation
ASCII
Power
Write
on
<CR>*pow=on#<CR>
Write
off
<CR>*pow=off#<CR>
Read
Status( on/off/cool down)
<CR>*pow=?#<CR>
Write
Source scan on
<CR>*scan=on#<CR>
Write
Source scan off
<CR>*scan=off#<CR>
Read
Source scan status
<CR>*scan=?#<CR>
Write
VGA
<CR>*sour=vga#<CR>
Write
DVI
<CR>*sour=dvi#<CR>
Write
HDTV
<CR>*sour=hdtv#<CR>
Write
YPbPr
<CR>*sour=YPbr#<CR>
Write
Composite
<CR>*sour=comp#<CR>
Write
S-Video
<CR>*sour=svid# <CR>
Write
YCbCr
<CR>*sour=YCbr#<CR>
Read
Status
<CR>*sour=?#<CR>
Write
Mute on
<CR>*mute=on#<CR>
Write
Mute off
<CR>*mute=off#<CR>
Read
Mute status
<CR>*mute=?#<CR>
Write
Volume +
<CR>*vol=+#<CR>
Write
Volume -
<CR>*vol=-#<CR>
Read
Volume status
<CR>*vol=?# <CR>
Write
Contrast +
<CR>*con=+#<CR>
Write
Contrast -
<CR>*con=-#<CR>
Read
Contrast value
<CR>*con=?#<CR>
Write
Brightness +
<CR>*bri=+#<CR>
Write
Brightness -
<CR>*bri=-#<CR>
Read
Brightness value
<CR>*bri=?#<CR>
Write
Aspect ratio 4:3
<CR>*asp=4:3#<CR>
Write
Aspect ratio 16:9
<CR>*asp=16:9#<CR>
Read
Aspect status
<CR>*asp=?#<CR>
Write
Blank on/off
<CR>*blank#<CR>
Read
Blank status
<CR>*blank=?#<CR>
Write
Freeze on/off
<CR>*freeze#<CR>
Read
Freeze status
<CR>*freeze=?#<CR>
Source Selection
Audio
Picture Setting
Function
Picture Setting
Lamp Control
Menu Control
Type
Operation
ASCII
Write
Auto adjust
<CR>*auto#<CR>
Write
Mirror: Normal
<CR>*mir=nor#<CR>
Write
Mirror: H Inverse
<CR>*mir=hinv#<CR>
Write
Mirror: V Inverse
<CR>*mir=vinv#<CR>
Write
Mirror: H&V Inverse
<CR>*mir=vhinv#<CR>
Read
Mirror status
<CR>*mir=?#<CR>
Write
Horizontal position shift right <CR>*hpos=left#<CR>
Write
Horizontal position shift left
<CR>*hpos=right#<CR>
Read
Horizontal position
<CR>*hpos=?#<CR>
Write
Vertical position shift up
<CR>*vpos=up#<CR>
Write
Vertical position shift down
<CR>*vpos=down#<CR>
Read
Vertical position
<CR>*vpos=?#<CR>
Write
Color temperature low
<CR>*ctmp=T3#<CR>
Write
Color temperature standard
<CR>*ctmp=T2#<CR>
Write
Color temperature high
<CR>*ctmp=T1#<CR>
Read
Color temperature status
<CR>*ctmp=?#<CR>
Write
Keystone +
<CR>*keyst=+#<CR>
Write
Keystone -
<CR>*keyst=-#<CR>
Read
Keystone status
<CR>*keyst=?#<CR>
Write
Preset mode: presentation(PC) <CR>*appmod=preset#<CR>
Write
preset mode: brightness
<CR>*appmod=bright#<CR>
Write
preset mode: srgb
<CR>*appmod=srgb#<CR>
Write
Preset mode: gaming
<CR>*appmod=game#<CR>
Write
Preset mode: video
<CR>*appmod=video#<CR>
Write
preset mode: movie
<CR>*appmod=mov#<CR>
Write
Preset mode: cinema
<CR>*appmod=cine#<CR>
Write
Preset mode: game
<CR>*appmod=game#<CR>
Write
Preset mode: photo
<CR>*appmod=phot#<CR>
Read
Preset mode status
<CR>*appmod=?#<CR>
Write
Reset Lamp usage hour
<CR>*ltim=rst#<CR>
Read
Lamp usage hour
<CR>*ltim=?#<CR>
Write
OSD Reset
<CR>*rst#<CR>
Write
English
<CR>*lang=eng#<CR>
Function
Type
Operation
ASCII
Menu Control
Write
FRE(Français)
<CR>*lang=fre#<CR>
Write
Deutsch
<CR>*lang=ger#<CR>
Write
Italiano
<CR>*lang=ita#<CR>
Write
Español
<CR>*lang=spa#<CR>
Write
<CR>*lang=pro#<CR>
Write
РУССКИЙ
繁體中文
Write
简体中文
<CR>*lang=chs#<CR>
Write
日本語
<CR>*lang=jap#<CR>
Write
<CR>*lang=kor#<CR>
Write
korean(한국어)
swidish
<CR>*lang=swd#<CR>
Write
dutch
<CR>*lang=dut#<CR>
Write
turkish
<CR>*lang=turk#<CR>
Write
czech
<CR>*lang=czech#<CR>
Write
portugese
<CR>*lang=portug#<CR>
Write
thai
<CR>*lang=thai#<CR>
Write
polish
<CR>*lang=pol#<CR>
Read
Language
<CR>*lang=?#<CR>
Read
Error status
<CR>*err#<CR>
Error status
<CR>*lang=cht#<CR>