Smooth Fitness 9.35HR Treadmill User`s manual

USER’S MANUAL
9.35HR MOTORIZED TREADMILL
USER WEIGHT LIMITATION: 350lbs(160kgs).
SERIAL NUMBER (found on frame):
2
9.35HR TREADMILL
PRECAUTIONS
For future service or related questions:
Please staple your receipt and/or write in the name and phone number of the retail store where you purchased your treadmill.
Name: ______________________________ Phone Number: ___________________ Receipt: ______________________
Precautions:
WARNING: To reduce the risk of burns, fire, electric shock, or injury to persons, read the following important precautions and
information before operating the treadmill. It is the responsibility of the owner to ensure that all users of this treadmill are
adequately informed of all warnings and precautions.
•
Use the treadmill only as described in this manual.
•
Place on a level surface, with 6 feet (2 m) of clearance behind it. Do not place the treadmill on any surface that blocks air
openings. To protect the floor or carpet from damage, place a mat under the treadmill.
•
When choosing a location for the treadmill be sure that the location and position permit access to a plug.
•
Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a garage or covered patio, or near
water.
•
Do not operate the treadmill where aerosol products are used or where oxygen is being administered.
•
Keep children under the age of 12 and pets away from the treadmill at all times.
•
The treadmill should not be used by persons weighing more than 350LBS (160 Kgs).
•
Never allow more than one person on the treadmill at a time. Wear appropriate exercise clothing when using the treadmill.
Do not wear loose clothing that could become caught in the treadmill. Athletic support clothes are recommended for both
men and women. Always wear athletic shoes. Never use the treadmill with bare feet, wearing only stockings, or in
sandals.
•
When connecting the power cord, plug the power cord into a grounded circuit. No other appliance should be on the same
circuit.
•
Always straddle the belt and allow it to start moving before stepping onto the belt.
•
Always examine your treadmill before using to ensure all parts are in working order.
•
Allow the belt to fully stop before dismounting.
•
Never insert any object or body parts into any opening.
•
Follow the safety information in regards to plugging in your treadmill.
•
Keep the power cord away from the incline wheels and do not run the power cord underneath your treadmill. Do not
operate the treadmill with a damaged or frayed power cord.
•
Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed by an
authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to follow these
instructions will void the treadmill warranty.
•
Never leave the treadmill unattended while it is running.
•
Use “safety key” when operating the treadmill and make sure the “safety key” is clipped to the users clothing.
•
Remove the “safety key” and store it in a safe place when the treadmill is not in use. Keep the “safety key” away from
children.
www.smoothfitness.com
3
POWER REQUIREMENTS
Power Requirements:
IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULT IN THE RISK OF AN ELECTRIC
SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE
PRODUCT IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILL NOT FIT
THE OUTLET; HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.
This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltage spikes, surges and
noise interference can result from weather conditions or from other appliances being turned on or off. To reduce the possibility of
treadmill damage, always use a surge protector (not included) with your treadmill.
Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surge protector with a
UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltage rating of 400V or less and an
electrical rating 110VAC, 15 amps.
This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistance for electric
current, should the treadmill malfunction. This treadmill is equipped with an electrical cord that has an equipment-grounding
conductor and a grounding plug. Always plug the power cord into a surge protector, and plug the surge protector into an
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
This product is for use on a nominal 110-volt circuit, and has a grounding plug that looks like the plug illustrated in the drawing
below.
GFCI outlets and GFCI Circuit Breakers are NOT recommended for use on this product. GFCI outlets and GFCI Circuit Breakers
may cause this equipment to function improperly.
4
9.35HR TREADMILL
BEFORE YOU BEGIN
Open the boxes:
Open the boxes of your new equipment. Inventory all parts included in the boxes, and compare them to the Supplied
Components and Supplied Hardware lists on pages 5-6 for a full count of the parts included. If you are missing any
parts or have any questions contact us directly at 888-800-1167
Assembly instructions are on pages 18-26.
Gather your tools:
Before you begin, make sure that you have gathered all the necessary tools you may require to assemble the unit
properly. Having all of the necessary equipment at hand will save time and make the assembly quick and hassle-free.
Clear your work area:
Make sure that you have cleared away a large enough space to properly assemble the unit. Make sure the space is
free from anything that may cause injury during assembly. After the unit is fully assembled, make sure there is a
comfortable amount of free area around the unit for unobstructed operation.
Invite a friend:
Some of the assembly steps may require heavy lifting. It is recommended that you obtain the assistance of another
person when assembling this product.
User Weight Limitation:
Please note that there is a weight limitation for this product. If you weigh more than 350LBS (Approx. 160 Kgs). It is
not recommended that you use this product. Serious injury may occur if the user’s weight exceeds the limit shown
here. This product is not intended to support users whose weight exceeds this limit.
Care and maintenance:
The safety level can be maintained only if it is examined for damage and wear.
Replace any defective components immediately and stop all use of the equipment until repaired.
Always take care when mounting the equipment. Straddle the equipment by placing your feet on the straddle rails.
Dismount from the equipment only after all parts have stopped.
Always check the wear and tear components like pulley, belts, etc.…To prevent injury.
There is an emergency stop, in the form of a SAFETY KEY, to prevent injury; you can stop the treadmill immediately
by actuating the emergency stop for emergency dismount.
www.smoothfitness.com
5
SUPPLIED COMPONENTS
This list identifies the major components you will use to assemble this product.
No.
Description
Qty.
A1
Computer
1
A2
Front Handlebar Assembly
1
A3
Handlebar
2
A4
Upright Assembly Left
1
A5
Upright Assembly Right
1
A6
Main Frame Assembly
1
G
Chest Belt
1
H
Power Cord
1
I
Running Belt Lubrication
1
107
Safety Key
2
116
Water Bottle
1
120
MP3 Connection Wire
1
310
Adjustable Cylinder
2
315
Adjustable Cylinder Cover – Upper
2
303
Upright Cover – LL
1
304
Upright Cover – LR
1
305
Upright Cover – RL
1
306
Upright Cover – RR
1
311
Upright Plastic Shroud – LL
1
312
Upright Plastic Shroud – LR
1
313
Upright Plastic Shroud – RL
1
314
Upright Plastic Shroud – RR
1
A1
A2
A6
107
A3
G
116
A4
A5
H
I
310
120
303
304
305
311
312
313
315
306
314
6
9.35HR TREADMILL
SUPPLIED HARDWARE
This list identifies the hardware you will use to assemble the product. To help distinguish between the various types of
screws and bolts, use the scale below to measure them and compare them to the sizes listed.
No.
Description
Qty.
804
M8x16mm Bolt
2
805
M8x50mm Bolt
12
806
#8x20mm Screw
18
807
4x15mm Screw
19
826
M8 Nylon Nut
2
843
M8x15mm Allen Head Bolt
4
845
13x42mm Shaft
2
846
8x23x2mm Washer
2
A
5mm Allen Key
1
B
8mm Allen Key
1
C
Screwdriver
1
D
Spanner
1
E
6mm Allen Wrench
1
MILLIMETERS
www.smoothfitness.com
COMPLETE PARTS LIST
Item No.
9.35HR-100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
9.35HR-200
201
202
203
204
205
206
207
208
9.35HR-300
301
303
304
305
306
307
308
309
310
311
312
313
314
Description
Qty.
Part No.
Complete Computer Console
Overlay
Computer Plastic Insert
Console PC Board
Console Housing – Upper
Console Housing – Bottom
Safety Key Base
Safety Key
Safety Key Wire – Upper
8pin Computer Wire – Upper
Computer Ground Wire
Hand Pulse Wire – Upper
E – Prom
Motion Control Board
Motion Control Board Wire
Motion Control Sensor Wire
Water Bottle Holder
Speaker Cover – Left
Speaker Cover – Right
Speaker
1
1
1
1
1
1
1
1
1
1
2
1
1
1
2
2
1
1
2
9.35HR-101
9.35HR-102
9.35HR-103
9.35HR-104
9.35HR-105
9.35HR-106
9.35HR-107
9.35HR-108
9.35HR-109
9.35HR-110
9.35HR-111
9.35HR-112
9.35HR-113
9.35HR-114
9.35HR-115
9.35HR-116
9.35HR-117
9.35HR-118
9.35HR-119
2
2
1
1
2
2
2
2
9.35HR-201
9.35HR-202
9.35HR-203
9.35HR-204
9.35HR-205
9.35HR-206
9.35HR-207
9.35HR-208
2
1
1
1
1
1
1
2
2
1
1
1
1
9.35HR-301
9.35HR-303
9.35HR-304
9.35HR-305
9.35HR-306
9.35HR-307
9.35HR-308
9.35HR-309
9.35HR-310
9.35HR-311
9.35HR-312
9.35HR-313
9.35HR-314
Complete Handlebar Components
Handlebar Tube
Handlebar Foam Grip
Front Handlebar
Front Handlebar Foam Grip – Short
Front Handlebar Foam Grip – Long
Hand Pulse Set
Motion Control
Motion Control Base
Complete Upright Components
Upright
Upright Cover – LL
Upright Cover – LR
Upright Cover – RL
Upright Cover – RR
Safety Key Wire – Middle
8pin Computer Wire – Middle
Motion Control Sensor Wire – Middle
Adjustable Cylinder
Upright Plastic Shroud – LL
Upright Plastic Shroud – LR
Upright Plastic Shroud – RL
Upright Plastic Shroud – RR
7
8
9.35HR TREADMILL
COMPLETE PARTS LIST
Item No.
Description
Qty.
Part No.
315
Adjustable Cylinder Cover - Upper
2
9.35HR-315
318
Fixing Inserts
2
9.35HR-318
9.35HR-400
Complete Base Frame Components
401
Base Frame
1
9.35HR-401
402
Safety Key Wire – Lower
1
9.35HR-402
403
8pin Computer Wire – Lower
1
9.35HR-403
404
Power Switch Plate Cover
1
9.35HR-404
405
Power Socket
1
9.35HR-405
406
Power Breaker
1
9.35HR-406
407
Power Switch
1
9.35HR-407
411
Bushing 34x48x23.3
4
9.35HR-411
412
Fix Bolt Sets
2
9.35HR-412
413
Caster
4
9.35HR-413
414
Circular Cushion
2
9.35HR-414
415
Level Adjuster
2
9.35HR-415
416
Base Frame End Cap
2
9.35HR-416
417
Oblong Cushion
2
9.35HR-417
426
Shock
1
9.35HR-426
9.35HR-500
Complete Motor Components
501
Motor Hood
1
9.35HR-501
502
Elevation Motor
1
9.35HR-502
503
Elevation Gear Sleeve
1
9.35HR-503
504
Driving Motor
1
9.35HR-504
505
Motor Holder
1
9.35HR-505
506
Driving Belt
1
9.35HR-506
507
Motor Control Board
1
9.35HR-507
508
Elevation Control Board
1
9.35HR-508
509
Elevation Support Tube
1
9.35HR-509
510
Elevation Support Tube Cover – Left
1
9.35HR-510
511
Motor Bottom Cover
1
9.35HR-511
512
Deck Frame Side Cover – Left
1
9.35HR-512
513
Plastic Clamp – Top
2
9.35HR-513
514
Plastic Clamp – Bottom
2
9.35HR-514
515
Plastic Clamp Bracket
2
9.35HR-515
516
Deck Rubber Cushion
2
9.35HR-516
517
Vent Cover
1
9.35HR-517
518
Elevation Support Tube Cover – Right
1
9.35HR-518
519
Deck Frame Side Cover – Right
1
9.35HR-519
9.35HR-600
Complete Running Deck Components
601
Running Belt
1
9.35HR-601
602
Side Rail
2
9.35HR-602
603
Running Deck
1
9.35HR-603
604
Side Rail End Cap – Left
1
9.35HR-604
www.smoothfitness.com
COMPLETE PARTS LIST
Item No.
Description
605
9.35HR-700
Side Rail End Cap – Right
Qty.
Part No.
1
9.35HR-605
Complete Deck Frame Components
701
Deck Frame
1
9.35HR-701
702
Front Roller Shaft
1
9.35HR-702
703
704
Front Roller
1
9.35HR-703
Roller Bearing 6203
4
9.35HR-704
705
Rear Roller Shaft
1
9.35HR-705
706
Rear Roller
1
9.35HR-706
707
Running Deck Support Tube
1
9.35HR-707
708
Running Deck Support Tube Foam Grip
1
9.35HR-708
709
Deck Frame
1
9.35HR-709
9.35HR-800
Complete Hardware Pack
801
#6x12mm Screws
12
9.35HR-801
803
#8x12mm Screws
8
9.35HR-803
804
M8x16mm Bolt
2
9.35HR-804
805
M8x50mm Bolt
12
9.35HR-805
806
#8x20mm Screw
18
9.35HR-806
807
4x15mm Screw
19
9.35HR-807
808
M5x8mm Screw
4
9.35HR-808
809
M8x16mm Screw
36
9.35HR-809
813
5x12x1mm Washer
8
9.35HR-813
814
M10 Nylon Nut
8
9.35HR-814
816
M14x90mm Bolt
2
9.35HR-816
817
DU Bearing
4
9.35HR-817
818
M10x35mm Bolt
10
9.35HR-818
819
#8x10mm Screw
7
9.35HR-819
820
#8x50mm Screw
2
9.35HR-820
821
M10x63mm Bolt
1
9.35HR-821
822
Fixed Block
8
9.35HR-822
823
M10x120mm Bolt
1
9.35HR-823
824
10x30x3mm Plate Washer
2
9.35HR-824
825
Compression Spring
1
9.35HR-825
826
M8 Nylon Nut
2
9.35HR-826
827
M8x20mm Bolt
6
9.35HR-827
828
8x13x2mm Spring Washer
12
9.35HR-828
829
8x16x3mm Washer
2
9.35HR-829
830
M10x110mm Bolt
1
9.35HR-830
832
M8x25mm Screw
10
9.35HR-832
833
M8 Nut
10
9.35HR-833
834
M8x70mm Bolt
3
9.35HR-834
838
M10x43mm Bolt
2
9.35HR-838
839
Cushion Pad
10
9.35HR-839
9
10
9.35HR TREADMILL
COMPLETE PARTS LIST
Item No.
Description
Qty.
Part No.
840
M10x40mm Bolt
1
9.35HR-840
841
M6x10mm Screw
2
9.35HR-841
842
M10x30mm Allen Head Bolt
2
9.35HR-842
843
M8x15mm Allen Head Bolt
4
9.35HR-843
845
13x42mm Shaft
2
9.35HR-845
846
8x23x2mm Washer
2
9.35HR-846
848
3x8mm Screw – Cone Point
6
9.35HR-848
www.smoothfitness.com
PARTS DIAGRAM
MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED
11
12
9.35HR TREADMILL
PARTS DIAGRAM
MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED.
www.smoothfitness.com
PARTS DIAGRAM
A MAJORITY OF THE PARTS SHOWN HERE HAVE BEEN PREASSEMBLED AT THE FACTORY.
13
14
9.35HR TREADMILL
PARTS DIAGRAM
MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED.
www.smoothfitness.com
PARTS DIAGRAM
MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED.
517
501
517
501
819
820
819
820
820
824
825
816
503
824
820
824
505
502823
825
816
503
824827
505
823
504
828 827
814
829
821
504
814
828
814
829
821
814
830
509
506
518
830
502
507
507
508
508
809
809
510
513
512
514
510
506
814
518
842
513
512
515514
819
809
819
509 513
819
809
515827
827
819
513
514
516
511
511
516
806
514 827
515 519
806
809
809
515 519
827
15
16
9.35HR TREADMILL
PARTS DIAGRAM
MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED.
602
602
604
601
832
809
605
603
822
818
www.smoothfitness.com
PARTS DIAGRAM
MOST OF THE PARTS SHOWN HERE HAVE BEEN PRE-ASSEMBLED.
702
703
704
840
814
704
707
704 706
705
708
834
841
701
704
828
834
833
828
833
839
828
709
828
828
814
413
838
833
833
833
828
833
17
18
9.35HR TREADMILL
ASSEMBLY
STEP 1: UNPACKING AND INVENTORY
(A)Remove your treadmill from the carton and place it on the floor in an open area.
(B)Remove the treadmill and all the components and hardware from the box.
(C)Check the quantities of all components and hardware with the component and hardware lists on pages 5-6
(D) After verifying inventory if there are any missing parts please contact Smooth fitness at 1-888-800-1167.
A1
A2
G
A3
H
120
310
311
312
A4
313
A6
107
I
303
A5
304
314
116
305
315
306
www.smoothfitness.com
19
ASSEMBLY
STEP 2:ASSEMBLE UPRIGHT
NOTE: MAKE SURE ALL WIRES ARE RECESSED INTO THE FRAME. DO NOT TRAP OR PINCH. DO NOT TIGHTEN BOLTS
UNTIL STEP9.
(A) Connect the Lower and middle section wire as seen below (307 to 402)(308 to 403).
(B) Insert any extra cable length into the Left Upright (301).
(C) Insert the Left and Right Uprights (301) into the Base Frame (401).
307
402
308
403
20
9.35HR TREADMILL
ASSEMBLY
STEP 3: ASSEMBLE THE SIDE HANDLEBARS
NOTE: SIDE RAILS ARE INTERCHANGEABLE FOR USE IN BOTH RIGHT AND
LEFT SIDES. MAKE SURE ALL WIRES RECESSED INTO THE FRAME. DO
NOT TRAP OR PINCH.
(A) Connect the Left Motion Control lower wire to the middle wire (207 to 309). As
Shown in the diagram below.
804
X2
(B) Insert the Left Handlebar (201) into the Upright Tube (301). Using one M8x16mm
Bolt (804) to secure the upper portion. Use two M8x50mm Bolts (805) to secure
the lower portion to the base frame, and use two M8x50mm Bolts (805) to secure
the middle portion to the upright.
805
X8
(C) Repeat the above process for the Right side.
309
207
www.smoothfitness.com
ASSEMBLY
STEP 4: ASSEMBLE FRONT HANDLEBAR
(A) Place the front handlebar (203) on top of the left and right uprights (301).
(B) Now secure the front handlebar with four M8x50mm bolts (805).
(C) Tighten all handlebar hardware (be sure not to pinch wires).
805 X4
21
22
9.35HR TREADMILL
ASSEMBLY
STEP 5: ATTACHING THE UPRIGHT COVER AND CONNECT COMPUTER CABLE
NOTE: BE CAREFUL NOT TO DAMAGE THE WIRES WHEN SECURING THE
UPRIGHT COVERS.
(A) Attach the Upright Cover – LR (304) to the Left upright (301), and secure using the
two 4x15mm Screws (807).
(B) Repeat the above process for the left side.
806 X4
(C) Lower the console (100) onto Left and Right Upright Covers, and secure with four
#8x20mm Screws (806).
807 X4
(D) Make all the necessary computer connections as pictured below. The connectors are
specially designed to only connect with the matching connectors.
(E) Before proceeding to the next steps recheck that all the cables are firmly connected.
www.smoothfitness.com
ASSEMBLY
STEP 6: Attach the Outside Upright Covers
NOTE: CAREFULLY FOLD THE COMPUTER CABLES AND TUCK THEM BETWEEN
THE PLASTIC RIDGES OF PARTS 304 AND 305 SO THEY WILL NO BE
PINCHED.
(A) Secure the ground wire onto the Right upright with one 4x15mm Screw (807).
(B) Attached the Upright Cover – RR (306) to the right side Upright Tube., and secure using
two #8x20mm Screws (806) into the console, then secure using two 4x15mm Screw
(807) into the Upright Tube.
(C) Repeat this process for the left side.
807
301
806
x4
807
X5
23
24
9.35HR TREADMILL
ASSEMBLY
STEP 7: ATTACH ADJUSTABLE CYLINDER TO TREADMILL FRAME
WARNING: THE PATENTED HYDRASUSPENSION SYSTEM REQUIRES THE
ADJUSTABLE CYLINDER TO BE TIGHT FITTING. PLEASE BE
PATIENT WITH THIS ASSEMBLY STEP.
(A) Put Adjustable Cylinder Cover-Upper (315) into Adjustable Cylinder (310).
(B) Attach the bottom of the Adjustable Cylinder (310) to the left Cylinder Mounting
Shaft (509) and secure with 8x23x2mm washer (846) and one M8 Nylon Nut (826).
826
X2
843
X4
845
X2
846
X2
(C) Attach the head of the Adjustable Cylinder (310) to the left upright (301):
a: Align the through hole on the head of the Adjustable Cylinder (310) with the
mounting hole on the frame (301).
b: As you slide the threaded shaft (845) through the aligned holes .
(D) Secure the cylinder head with two M8x15mm Allen Head Bolts (843).
(E) Repeat this procedure to assemble the Adjustable Cylinder on the right side of the
frame.
www.smoothfitness.com
ASSEMBLY
STEP 8: ASSEMBLE FRONT PLASTIC SHROUDS
(A) Attach the outer Left Upright Plastic Shroud – LL (311) , the inner Left Upright Plastic
Shroud – LR (312) and the Adjustable Cylinder Cover – Upper 315 to the Left Upright
(301) and secure with five M8x20mm Screws (806) and five 4x15mm Screw (807).
(B) Repeat the above process for the Right side.
806 X10
807 X10
25
26
9.35HR TREADMILL
ASSEMBLY
STEP 9:Securing of the Upright Tubes
NOTE: ONLY TURN BOLTS CLOCKWISE. The Allen Bolt Sets (412) have been pre-assembled in the Base Frame (401).
(A) Secure The Upright Tubes by tightening the Allen Bolt (412), located in the Upright Tube, clockwise.
www.smoothfitness.com
27
STABILIZER ADJUSTMENT
FOLLOW THESE INSTRUCTIONS TO LEVEL YOUR TREADMILL:
An uneven floor or improper stabilizer level can cause the treadmill to wobble during use as well as the incline adjustment to
function incorrectly. Please follow the procedure described below to make sure the treadmill stabilizer is adjusted correctly prior to
use. You may need the assistance of another person to perform this adjustment.
First locate the two adjustable stabilizers under the base frame. Then simply rotate them in or out to adjust the level of
the treadmill. When properly adjusted the treadmill should sit firmly on both stabilizers and all cushions.
Locate the two adjustable stabilizers under the base frame.
Treadmill should sit firmly on both stabilizers and all cushions.
28
9.35HR TREADMILL
FEATURES
Serial Number Location
Insert safety key
The safety key must be inserted for the treadmill to function. The safety key clip
should be worn at all times when the treadmill is in use. This safety feature is designed
to prevent injury.
www.smoothfitness.com
MOTION CONTROL OPERATION
MOTION CONTROL:
Walking belt speed can be increased, decreased or stopped using the Motion
Control sensors on the handlebars. To do this follow the instructions below:
1.
Press the
button on the console to switch the motion control
function on and off:
•
•
When the LED light is ON the MOTION CONTROL is active.
When the LED light is OFF the MOTION CONTROL is off.
2.
After switching on the MOTION CONTROL wave your right hand
approximately 6 inches above the motion sensor on the right handle
bar to increase the speed. The sensor will sound one short BEEP
per scan and speed up by 0.1 MPH per BEEP. Holding your right
hand approximately 6 inches above the right sensor constantly
results in the sensor sounding one long BEEP per second and
speeding up by 0.5 MPH per second.
2. Use right sensor to speed up.
3.
Wave you left hand approximately 6 inches above the motion sensor
on the left handle bar to decrease the speed. The sensor will sound
one short BEEP per scan and decrease speed by 0.1 MPH. Holding
your left hand approximately 6 inches above the left sensor
constantly results in the sensor sounding one long BEEP per second
and decreasing speed by 0.5 MPH per second.
3. Use left sensor to slow down.
4.
Wave both hands approximately 6 inches above both motion
sensors at the same time. The sensor will sound two short BEEP
sounds then stop the belt.
•
Always switch off the motion control function by pressing the
MOTION CONTROL button on the console before turning
off the power to the treadmill.
4. Use both sensors to stop belt.
29
30
9.35HR TREADMILL
MAINTAINENCE
HOW TO MAINTAIN THE 9.35HR TREADMILL:
Proper maintenance is very important to ensure your treadmill is always in top working condition. Improper maintenance could
cause damage or shorten the life of your treadmill and exceed the LIMITED WARRANTY coverage.
•
Important: DO NOT use abrasives or solvents to clean the treadmill. To prevent damage to the computer, keep liquids
away and keep it out of direct sunlight.
•
Inspect and tighten all parts of the treadmill regularly. Replace any damaged or worn parts immediately.
BELT ADJUSTMENT:
ALL BELT ADJUSTMENTS ARE CONSIDERED MAINTENANCE, AND ARE THE RESPONSIBILITY OF THE END USER.
Belt adjustment and tension performs two functions: adjustment for tension and centering. The running belt has been adjusted
properly at the factory. However transportation, uneven flooring or other unpredicted reasons could cause the belt to shift off center
resulting in the belt rubbing on the plastic side rail or end caps and possibly causing damage to the equipment. To adjust the belt
back to it’s proper position please follow the directions below:
•
Walking belt has shifted to the left: First unplug the power cord from the surge protector. Using the hex key provided,
turn the left rear roller adjustment bolt 1/4 turn in the clockwise direction. Plug the power cord back into the surge
protector and run the treadmill at 2.5 mph. You should see the belt start to correct itself, moving back towards the center.
Repeat the above procedure until the walking belt is centered. It may be necessary to set walking belt tension once you
have completed this procedure if the belt feels like it is slipping while walking. Refer below to the "Walking belt slipping"
instructions.
•
Walking belt has shifted to the right: First unplug the power cord from the surge protector. Using the hex key provided,
turn the right rear roller adjustment bolt 1/4 turn in the clockwise direction. Plug the power cord back into the surge
protector and run the treadmill at 2.5 mph. You should see the belt start to correct itself, moving back towards the center.
Repeat the above procedure until the walking belt is centered. It may be necessary to set walking belt tension once you
have completed this procedure if the belt feels like it is slipping while walking. Refer below to the "Walking belt slipping"
instructions.
•
Walking belt is slipping: First unplug the power cord from the surge protector. Using the hex key provided, turn both the
left and right rear roller adjustment bolts the equal amounts , 1/2 turn in the clockwise direction. Plug the power cord back
into the surge protector and run the treadmill at 2.5 mph. You should now walk on the belt to determine if the belt is still
slipping. Repeat the above procedure until the walking belt is not slipping. The tension should be just tight enough not to
slip. If proper tension cannot be achieved within four attempts please contact Smooth Fitness Technical Support. Belt
centering may be necessary once you have completed the tensioning procedure.
WARNING! Do not over tighten rollers! This will cause premature roller bearing failure!
Right and left tension bolts are located at the rear of the treadmill.
www.smoothfitness.com
31
MAINTAINENCE
CLEANING:
Routine cleaning of your treadmill will extend the product's life.
•
Warning: To prevent electrical shock, be sure the power to the treadmill is OFF and the power cord is unplugged from the
wall electrical outlet before attempting any cleaning or maintenance.
•
Important: DO NOT use abrasives or solvents to clean the treadmill. To prevent damage to the computer, keep liquids
away and keep it out of direct sunlight.
•
After each workout: Wipe off the console and other treadmill surfaces with a clean, water dampened soft cloth to
remove excess perspiration.
•
Weekly: Use of a treadmill mat is recommended for ease of cleaning. Dirt from your shoes contacts the belt and
eventually makes it to underneath the treadmill. Vacuum underneath treadmill once a week.
DECK LUBRICATION:
The walking belt has been pre-lubricated at the factory. However, it is recommended that the running deck be checked periodically
for lubrication to ensure optimal treadmill performance. Your treadmill should not have to be lubricated usually within the first 400
hours of use.
Every 2 months of operation lift the sides of the walking belt and feel the top surface of the running deck as far as you can reach. If
you feel signs of silicone, no further lubrication is required. If it feels dry to the touch, follow the instructions below.
. To purchase lubricant Kit please contact Smooth Fitness 1-888-800-1167
To apply lubricant under the walking belt:
1.
Position the walking belt so that the seam is located on top and in center of the walking board.
2.
Insert the spray nozzle into the spray head of the lubricant can.
3.
While lifting the side of the walking belt, position the spray nozzle between the walking belt and the board approximately 6"
from the front of the treadmill and as far to the center as possible. Apply the silicone spray to the walking board, moving
from the front of the treadmill to the rear. Repeat this on the other side of the belt. Spray approximately 1/4 bottle
(supplied with treadmill) each time.
Allow the silicone to "set" for 1 minute before using the treadmill.
Spray lubricant from to back.
32
9.35HR TREADMILL
WARRANTY
LIMITED HOME USE WARRANTY – SMOOTH FITNESS Treadmills Warranty
Warranty Coverage: EVO Fitness and Smooth Fitness, Inc. ("Smooth Fitness") warrants to the original owner that each new product to be free
from defects in workmanship and material, under normal use and conditions.
Period of Coverage: The Warranty on this product runs from the date of original purchase using the following schedule:
Model Name
9.35HR
Frame
Lifetime
Drive Motor
Lifetime
Parts & Electronics
Lifetime Excluding TV
Labor
1 year
Labor: Smooth Fitness will reimburse for labor costs for One (1) year. Smooth Fitness reserves the right to either:
Hire and reimburse an independent service technician who will come into the home for the repair,
OR
In the event that there is not an available certified Smooth Fitness service technician, Smooth will send the part directly to the consumer and will pay
$75 US per occurrence for the labor costs of such repair. If multiple repair attempts must be made for one reported problem, Smooth will only
reimburse once per occurrence.
Smooth Fitness reserves the right to inspect damaged parts for misuse. Your Original Receipt is proof of purchase and should be kept with the
product manual. You may be required to show proof of purchase prior to warranty service being initiated.
Remedy Provided by Smooth Fitness: Smooth Fitness will provide a replacement part free of charge if a defect is found during the Warranty
period. Smooth Fitness may at its discretion, choose to provide any of following parts or repair options. In the event that a part is determined in need
of replacement, upon receipt of the part by Smooth Fitness, Smooth Fitness may send out the part by UPS ground or another such carrier directly to
the customer’s home.
Any redemption may be by repair or replacement of the affected parts and/or product at the sole discretion of Smooth Fitness, by personnel
approved by Smooth Fitness.
Parts repaired or replaced pursuant to this Warranty shall be warranted for the unexpired portion of the Warranty applying to the original product.
Any technical advice furnished before or after delivery in regard to the use or application of Smooth Fitness products is furnished without charge
and on the basis that it represents Smooth Fitness' best judgment under the circumstances but that the advice is used at your sole risk.
Procedure for Obtaining Your Remedy Under This Warranty: To obtain service on a Smooth Fitness product, call Smooth Fitness. In the
instance that service is not available in an area, Smooth Fitness, at its discretion, can either 1) find a service technician in your area to perform
warranty service, 2) have a local dealer perform warranty service, or 3) send the warranty parts to you and reimburse as described above. To help
the technician assist you, please have the following information ready:
•
Model name or number from the cover of the manual;
•
Serial number located on the frame of the unit; and
•
The part description and the order number.
Limitations on Warranty: This Warranty does not cover any problems, damages or failures that are caused by accident, improper assembly,
failure to observe cautionary labels on the product, failure to operate the product correctly, power grid failures or spikes from your local electricity
provider, abuse or freight damage. Smooth Fitness does not warrant against any damage or defects that may result from repair or alterations made
to the product by an unauthorized repair facility. In order for this warranty to be valid, all Smooth Fitness and EVO Fitness exercise equipment must
be stored and used in a fully finished and livable room within the residence (not including an indoor swimming pool room).
This Warranty shall terminate if you sell or otherwise transfer this product. This Warranty does not apply to any product shipped or handled outside
of the United States or Canada. This Warranty does not apply if the product is used as a rental product or in commercial use. Consequential and
incidental damages are not recoverable under this Warranty. (Some states do not allow
the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.)
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER EXPRESS WARRANTIES. ALL IMPLIED WARRANTIES,
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO ONE
(1) YEAR FROM THE EFFECTIVE DATE OF THIS WARRANTY. SMOOTH FITNESS IS NOT
LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES RESULTING FROM ANY DEFECT IN PARTS NOR FOR
ANY BREACH OF EXPRESS OR IMPLIED WARRANTIES. SMOOTH FITNESS' SOLE LIABILITY UNDER THIS
WARRANTY IS LIMITED TO THE TERMS DESCRIBED IN THIS FORM. THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
FORM WS-1 (rev. 03/2008)
www.smoothfitness.com
33
IMPORTANT STEPS
Warning:
Before using this product, please consult your personal physician for a complete physical examination. Frequent and strenuous
exercise should be approved by your doctor first. If any discomfort should result from your use of this product, stop exercising and
consult your doctor. Proper usage of this product is essential. Please read your manual carefully before exercising.
Please keep all children away from the equipment during use and when equipment is unattended.
Always wear appropriate clothing, including athletic shoes, when exercising. Do not wear loose clothing that could become caught
during exercising.
Make sure that all bolts and nuts are tightened when equipment is in use. Periodic maintenance is required on all exercise
equipment to keep it in good condition.
Before beginning:
How you begin your exercise program depends on your physical condition. If you have been inactive for several years, or are
severely overweight, you must start slowly and increase your time gradually, a few minutes per week.
Initially you may be able to exercise only for a few minutes in your target zone. However, your aerobic fitness will improve over the
next six to eight weeks. Don’t be discouraged if it takes longer. It’s important to work at your own pace. Ultimately, you’ll be able
to exercise continuously for 30 minutes. And the better your aerobic fitness, the harder you will have to work to stay in your target
zone. But remember these essentials:
•
Contact your physician before starting a workout or training program. Have your doctor review your training and diet
programs to advise you of a workout routine you should adopt.
•
Begin your training program slowly with realistic goals that have been set by you and your doctor.
•
Supplement your program with some type of aerobic exercise such as walking, jogging, swimming, dancing and/or
bicycling. Monitor your pulse frequently. If you do not have an electronic heart rate monitor, have your physician show
you the proper way to manually check your pulse by using your wrist or neck. Establish your target heart rate based on
your age and condition.
•
Drink plenty of fluids during the course of your routine. You must replace the water content lost from excessive exercising
to avoid dehydration. Avoid drinking large amounts of cold liquids. Fluids should be at room temperature when
consumed.
34
9.35HR TREADMILL
TARGET HEART RATE
Finding your pulse:
To make sure your heart is beating in its target zone, you’ll need to know how to monitor your heart rate. The easiest way is to feel
the pulse in the carotid artery on either side of your neck, between the windpipe and the large neck muscles. Count the number of
beats in ten seconds, and then multiply that number by six. This gives you the number of beats per minute.
How fast should your heart beat during aerobic exercise? Fast enough to reach and stay in its “target zone,” a range of beats per
minute that is largely determined by your age and physical condition. To determine your target zone, consult the chart we have
provided.
YOUR HEART RATE in beats per minute
FIND YOUR TARGET HEART RATE
200
180
160
140
120
100
80
20
25
30
35
40
45
50
YOUR AGE in years
55
60
65
70
ADVANCED: Sports, athletic conditioning or interval training
FITNESS: Optimal training, aerobic or cardiovascular
HEALTH: Beginner, low intensity with long duration produces fat burning
Aerobic exercise:
Is any sustained activity that sends oxygen to your muscles via your heart and lungs. It will improve the fitness of your lungs and
heart: your body’s most important muscle. Aerobic fitness is promoted by any activity that uses your large muscle groups - arms,
legs or buttocks, for example. Your heart beats quickly and you breathe deeply. An aerobic exercise should be part of your entire
exercise routine.
www.smoothfitness.com
35
MUSCLE CHART
Targeted muscle groups:
The exercise routine that is performed on this product will develop primarily lower body muscle groups. These muscle groups are
shown in gray color on the chart below.
MUSCLE GROUPS
A
Shoulder muscles
B
Pectoral muscles
C
Bicep muscle
D
Abdominal muscles
E
Forearm muscles
F
Quadricep muscles
Calf muscles
G
Trapezius muscles
H
Tricep muscles
I
Back muscles
J
Gluteal muscles
K
Hamstring muscles
L
36
9.35HR TREADMILL
STRETCHING ROUTINE
Warm up and cool down:
A successful exercise program consists of a warm-up, aerobic exercise, and a cool-down. Do the entire program at least two and
preferably three times a week, resting for a day between workouts. After several months, you can increase your workouts to four or
five times per week.
Warming up is an important part of your workout, and should begin every session. It prepares your body for more strenuous
exercise by heating up and stretching out your muscles, increasing your circulation and pulse rate, and delivering more oxygen to
your muscles. At the end of your workout, repeat these exercises to reduce sore muscle problems. We suggest the warm-up and
cool-down exercises on the following pages:
Toe Touch:
Slowly bend forward from
your waist, letting your back
and shoulders relax as you
stretch toward your toes.
Reach down as far as you
can and hold for 15 counts.
Shoulder Lift:
Lift your right shoulder up
toward your ear for one
count. Then lift your left
shoulder up for one count as
you lower your right
shoulder.
Inner Thigh Stretch:
Sit with the soles of your feet
together with your knees
pointing outward. Pull your
feet as close into your groin
as possible. Gently push
your knees towards the floor.
Hold for 15 counts.
Hamstring Stretch:
Sit with your right leg
extended. Rest the sole of
your left foot against your
right inner thigh. Stretch
toward your toe as far as
possible. Hold for 15 counts.
Relax and then repeat with
left leg extended.
Side Stretch:
Open your arms to the side
and continue lifting them until
they are over your head.
Reach your right arm as far
upward toward the ceiling as
you can for one count. Feel
the stretch up your right side.
Repeat this action with your
left arm.
Calf-Achilles Stretch:
Lean against a wall with your
left leg in front of the right
and your arms forward. Keep
your right leg straight and the
left foot on the floor; then
bend the left leg and lean
forward by moving your hips
toward the wall. Hold, and
then repeat on the other side
for 15 counts.
Head Roll:
Rotate your head to the right
for one count, feeling the
stretch up the left side of your
neck. Next, rotate your head
back for one count, stretching
your chin to the ceiling and
letting your mouth open.
Rotate your head to the left
for one count, and finally,
drop your head to your chest
for one count.
www.smoothfitness.com
37
TROUBLESHOOTING
NOTE: Do not touch any internal electric wires without consulting the manufacturer.
Treadmill will not start:
Symptom
Treadmill will not power up
Resolution
Check the following:
Make sure the power cord is plugged into a
surge protector, the surge protector is
plugged into a properly grounded outlet and
the surge protector is turned on (refer to the
Power Requirements section in this manual).
Equipment circuit breaker is in the reset
position
Equipment power switch is in the on position
Safety key is properly inserted into the
computer console
Wall outlet is properly functioning with correct
voltage (Have an electrician check for
inadequate voltage at the outlet refer to the
Power Requirements section in this manual)
House circuit breaker is reset and is the
proper size. (refer to the Power
Requirements section in this manual)
Safety key is properly inserted into the
computer console
Equipment circuit breaker is in the reset
position
House circuit breaker is reset, meets proper
requirements and if worn replaced by an
electrician. (refer to the Power Requirements
section in this manual)
Program time has expired
Check for proper positioning of spring knob for
folding(See procedure in owners manual)
Power Fold only
Check for proper positioning of spring knob
for folding(See procedure in owners manual)
Manual Fold only
Folding locking lever is depressed
Metric/English conversion (See owners manual
for Metric/English conversion process)
Metric/English conversion (See owners manual
for Metric/English conversion process)
Treadmill is properly leveled(See procedure
in owners manual)
Center running belt (See Centering
procedure in owners manual)
Tension running belt (See process in owners
manual)
Metric/English conversion (See owners manual
for Metric/English conversion process)
Treadmill stops operation during use
Treadmill will not incline(Power fold models only)
Treadmill will not unfold
Treadmill running belt moves slower than speed
displayed on computer
Treadmill running belt moves slower than speed
displayed on computer
Running belt is not centered
Running belt is slipping or hesitating while in use
Treadmill running belt moves slower than speed
displayed on computer
Treadmill is properly leveled(See procedure
in owners manual)
Center running belt (See Centering
procedure in owners manual)
Tension running belt (See process in owners
manual)
Running belt is not centered
Running belt is slipping or hesitating while in use
Smooth thFitness
780 5 Ave
King of Prussia, PA 19406
Toll Free Customer Service:
1.888.800.1167
Website:
www.smoothfitness.com