advertisement
P5N-T Deluxe
E3411
First Edition V1
October 2007 ii
Copyright © 2007 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE,
AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO
RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners’ benefit, without intent to infringe.
Contents
Notices .......................................................................................................... v
P5N-T Deluxe specifications summary ..................................................... ix
Chapter 1:
Product introduction
1.2 Package contents ......................................................................... 1-1
1.3.1 Product highlights ........................................................... 1-2
1.3.2 ASUS AI Lifestyle unique features .................................. 1-4
1.3.3 ASUS Intelligent Performance and Overclocking features .............................................. 1-8
Chapter 2:
Hardware information
2.1 Before you proceed ..................................................................... 2-1
2.2 Motherboard overview ................................................................. 2-2
2.2.1 Placement direction ........................................................ 2-2
2.2.2 Screw holes .................................................................... 2-2
2.2.3 Motherboard layout ......................................................... 2-3
2.2.4 Layout contents ............................................................... 2-4
2.3 Central Processing Unit (CPU) ................................................... 2-6
2.3.1 Installing the CPU ........................................................... 2-7
2.3.2 Installing the CPU heatsink and fan ................................ 2-9
2.3.3 Uninstalling the CPU heatsink and fan ..........................2-11
2.4 System memory ......................................................................... 2-13
2.4.1 Overview ....................................................................... 2-13
2.4.2 Memory configurations .................................................. 2-13
2.4.3 Installing a DIMM .......................................................... 2-15
2.4.4 Removing a DIMM ........................................................ 2-15
2.5 Expansion slots .......................................................................... 2-16
2.5.1 Installing an expansion card ......................................... 2-16
2.5.2 Configuring an expansion card ..................................... 2-16
2.5.3 Interrupt assignments ................................................... 2-17
2.5.4 PCI slot ......................................................................... 2-18
2.5.5 PCI Express x1 slots ..................................................... 2-18
2.5.6 PCI Express 2.0 x16 slots ............................................. 2-18
iii
iv
Contents
2.7.1 Rear panel connectors .................................................. 2-21
2.7.2 Internal connectors ....................................................... 2-23
2.7.3 Installing the optional fans ............................................ 2-33
Chapter 3:
Powering up
3.1 Starting up for the first time ........................................................ 3-1
3.2 Turning off the computer ............................................................. 3-2
3.2.1 Using the OS shut down function .................................... 3-2
3.2.2 Using the dual function power switch .............................. 3-2
Chapter 4:
BIOS up
4.1 Managing and updating your BIOS ............................................ 4-1
4.1.1 ASUS Update utility ........................................................ 4-1
4.1.2 Creating a bootable floppy disk ....................................... 4-4
4.1.3 ASUS EZ Flash 2 utility ................................................... 4-5
4.1.4 Updating the BIOS .......................................................... 4-6
4.1.5 Saving the current BIOS file ............................................ 4-8
4.1.6 ASUS CrashFree BIOS 3 utility ...................................... 4-9
4.2 BIOS setup program .................................................................... 4-9
4.2.1 BIOS menu screen ........................................................ 4-10
4.2.2 Menu bar ....................................................................... 4-10
4.2.3 Legend bar .....................................................................4-11
4.2.4 Menu items ....................................................................4-11
4.2.5 Sub-menu items .............................................................4-11
4.2.6 Configuration fields ........................................................4-11
4.2.7 Pop-up window ............................................................. 4-12
4.2.8 General help ................................................................. 4-12
4.3.1 System Time [xx:xx:xx] ................................................. 4-13
4.3.2 System Date [Day xx/xx/xxxx] ....................................... 4-13
4.3.3 Language [English] ....................................................... 4-13
4.3.4 Legacy Diskette A [1.44M, 3.5 in.] ................................. 4-13
4.3.5 Primary IDE Master/Slave ............................................. 4-14
4.3.7 HDD SMART Monitoring [Disabled] .............................. 4-17
4.3.8 Installed Memory [xxx MB] ............................................ 4-17
4.3.9 Usable Memory [XXX MB] ............................................ 4-17
4.4 Extreme Tweaker menu ............................................................. 4-18
4.4.1 AI Tuning [Auto] ............................................................ 4-18
4.4.2 Overclocking ................................................................. 4-21
4.4.3 Over Voltage ................................................................. 4-23
4.4.4 NVIDIA GPU Ex [Disabled] ........................................... 4-24
4.4.5 SLI-Ready Memory [Disabled] ...................................... 4-24
4.4.6 SLI-Ready Memory CPUOC [CPUOC 0%] ................... 4-24
4.5 Advanced menu ......................................................................... 4-25
4.5.1 AI NET2 ........................................................................ 4-25
4.5.2 PCIPnP ......................................................................... 4-26
4.5.3 Onboard Device Configuration ...................................... 4-27
4.6 Power menu ................................................................................ 4-30
4.6.1 ACPI Suspend Type [S1&S3]........................................ 4-30
4.6.2 ACPI APIC Support [Enabled] ....................................... 4-30
4.6.3 APM Configuration ........................................................ 4-31
4.6.4 Hardware Monitor ......................................................... 4-33
4.7.1 Boot Device Priority ...................................................... 4-35
4.7.2 Removable Drives ......................................................... 4-35
4.7.3 Hard Disk Drives ........................................................... 4-36
4.7.4 CDROM Drives ............................................................. 4-36
4.7.5 Boot Settings Configuration ......................................... 4-37
4.7.6 Security ......................................................................... 4-38
4.8.1 ASUS O.C. Profile ......................................................... 4-40
4.8.3 ASUS EZ Flash 2 .......................................................... 4-42
Chapter 5: Software support
5.1 Installing an operating system ................................................... 5-1
5.2 Support DVD information ............................................................ 5-1
5.2.1 Running the support DVD ............................................... 5-1
5.2.2 Drivers menu ................................................................... 5-2
v
vi
5.2.3 Utilities menu .................................................................. 5-3
5.2.4 Make disk menu .............................................................. 5-5
5.2.5 Manual menu .................................................................. 5-6
5.2.6 ASUS Contact information .............................................. 5-6
5.2.7 Other information ............................................................ 5-7
5.3 Software information ................................................................... 5-9
5.3.1 ASUS MyLogo3™ ........................................................... 5-9
5.3.2 AI NET2 .........................................................................5-11
5.3.3 ASUS PC Probe II ......................................................... 5-12
5.3.4 ASUS AI Suite ............................................................... 5-18
5.3.5 ASUS EPU Utility -- AI Gear 3 ...................................... 5-20
5.3.6 ASUS AI Nap ................................................................ 5-21
5.3.7 ASUS Q-Fan 2 .............................................................. 5-22
5.3.8 ASUS AI Booster ........................................................... 5-23
5.3.9 ASUS AI Direct Link ...................................................... 5-24
High Definition Audio utility) ... 5-26
5.4 RAID configurations .................................................................. 5-35
5.4.1 RAID definitions ............................................................ 5-35
RAID configurations........................................ 5-36
5.5 Creating a RAID driver disk ....................................................... 5-43
Chapter 6:
NVIDIA
SLI™ technology support
Requirements ................................................................................. 6-1
6.2 Graphics card setup .................................................................... 6-2
6.2.1 Installing three SLI-ready graphics cards ........................ 6-2
6.2.2 Installing two SLI-ready graphics cards .......................... 6-6
6.2.3 Installing the device drivers ............................................. 6-7
6.2.3 Enabling the multi-GPU feature in Windows
Appendix: CPU features
EM64T ..................................................................................A-1
Technology (EIST) ........................A-1
A.2.1 System requirements ......................................................A-1
A.2.2 Using the EIST ................................................................A-2
Hyper-Threading Technology ...........................................A-3
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer’s instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
vii
viii
Safety information
Electrical safety
• To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system.
• When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected. If possible, disconnect all power cables from the existing system before you add a device.
• Before connecting or removing signal cables from the motherboard, ensure that all power cables are unplugged.
• Seek professional assistance before using an adapter or extension cord.
These devices could interrupt the grounding circuit.
• Make sure that your power supply is set to the correct voltage in your area.
If you are not sure about the voltage of the electrical outlet you are using, contact your local power company.
• If the power supply is broken, do not try to fix it by yourself. Contact a qualified service technician or your retailer.
Operation safety
• Before installing the motherboard and adding devices on it, carefully read all the manuals that came with the package.
• Before using the product, make sure all cables are correctly connected and the power cables are not damaged. If you detect any damage, contact your dealer immediately.
• To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry.
• Avoid dust, humidity, and temperature extremes. Do not place the product in any area where it may become wet.
• Place the product on a stable surface.
• If you encounter technical problems with the product, contact a qualified service technician or your retailer.
This symbol of the crossed out wheeled bin indicates that the product (electrical, electronic equipment and mercury-containing button cell battery) should not be placed in municipal waste. Check local regulations for disposal of electronic products.
About this guide
This user guide contains the information you need when installing and configuring the motherboard.
How this guide is organized
This guide contains the following parts:
• Chapter 1: Product introduction
This chapter describes the features of the motherboard and the new technology it supports.
• Chapter 2: Hardware information
This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
• Chapter 3: Powering up
This chapter describes the power up sequence and ways of shutting down the system.
• Chapter 4: BIOS setup
This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
• Chapter 5: Software support
This chapter describes the contents of the support DVD that comes with the motherboard package and the software.
• Chapter 6: NVIDIA
®
SLI™ technology support
This chapter tells how to install SLI-ready PCI Express graphics cards.
• Appendix: CPU features
The Appendix describes the CPU features and technologies that the motherboard supports.
Where to find more information
Refer to the following sources for additional information and for product and software updates.
1. ASUS websites
The ASUS website provides updated information on ASUS hardware and software products. Refer to the ASUS contact information.
2. Optional documentation
Your product package may include optional documentation, such as warranty flyers, that may have been added by your dealer. These documents are not part of the standard package.
ix
x
Conventions used in this guide
To make sure that you perform certain tasks properly, take note of the following symbols used throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself when trying to complete a task.
CAUTION: Information to prevent damage to the components when trying to complete a task.
IMPORTANT: Instructions that you MUST follow to complete a task.
NOTE: Tips and additional information to help you complete a task.
Typography
Bold text
Italics
<Key>
<Key1+Key2+Key3>
Command
Indicates a menu or an item to select.
Used to emphasize a word or a phrase.
Keys enclosed in the less-than and greater-than sign means that you must press the enclosed key.
Example: <Enter> means that you must press the
Enter or Return key.
If you must press two or more keys simultaneously, the key names are linked with a plus sign (+).
Example: <Ctrl+Alt+D>
Means that you must type the command exactly as shown, then supply the required item or value enclosed in brackets.
Example: At the DOS prompt, type the command line:
format A:/S
P5N-T Deluxe specifications summary
CPU
Chipset
Front Side Bus
Memory
Expansion slots
Scalable Link Interface
(SLI™)
Storage
LAN
High Definition Audio
IEEE 1394
USB
LGA775 socket for Intel
®
Core™2 Quad /
Core™2 Extreme / Core™2 Duo / Pentium
Pentium
Intel
®
®
D / Pentium
®
4 Processors
next generation 45nm Multi-Core CPU
®
Extreme /
Compatible with Intel
®
05B/05A/06 processors
Note: Visit the ASUS website at www.asus.com for the Intel
®
CPU support list.
NVIDIA
® nForce 780i SLI
1333 / 1066 / 800 MHz
4 x DIMM, max. 8GB, DDR2 1066/800/667 MHz,
non-ECC, un-buffered memory
Dual channel memory architecture
Note: Visit the ASUS website at www.asus.com for the latest Qualified
Vendors List (QVL).
(blue �PCIe 2.0 x16 mode, black �
PCIe x16 mode) with SLI™ suppport
2 x PCIe x1
1 x PCI
Supports three identical NVIDIA
cards (all at x16 mode)
®
SLI™-Ready graphics
Southbridge supports:
- 1 x Ultra DMA 133/100/66
- 6 x Serial ATA 3 Gb/s
- NVIDIA
®
MediaShield™ RAID supports RAID 0, 1,
10(0+1), 5 and JBOD configuration across Serial
ATA drives
Marvell
®
88E1116 PCIe Gigabit LAN controller, featuring
AI NET2
ADI
®
1988B 8-channel High Definition Audio CODEC
Supports Jack-Sensing, Enumeration, and
Multi-streaming
Coaxial / Optical S/PDIF out ports at back panel
controller supports:
- 2 x IEEE 1394a connectors (one at mid-board; one
at back panel)
Supports up to 10 USB 2.0 ports (6 at mid-board, 4 at
back panel)
(continued on the next page)
xi
xii
ASUS AI Lifestyle
Unique features
ASUS Stylish Features
ASUS Exclusive
Overclocking features
ASUS Power Saving Solution:
- ASUS EPU (Energy Processing Unit)
- ASUS 3rd Generation 8-phase Power Design
- ASUS AI Nap
ASUS AI Lifestyle Features:
- ASUS AI Direct Link
ASUS Quiet Thermal Solution:
- ASUS Fanless Design: Heat-pipe solution
- ASUS Fanless Design: StackCool 2
- ASUS Q-Fan 2
- ASUS Optional Fan for Water-cooling or Passive-
Cooling only
ASUS Crystal Sound:
- ASUS Audio 2
- ASUS Noise Filter
ASUS EZ DIY:
- ASUS Q-Shield
- ASUS Q-Connector
- ASUS O.C. Profile
- ASUS CrashFree BIOS 3
- ASUS EZ Flash 2
- ASUS AI Slot Detector
ASUS MyLogo3™
Multi-language BIOS
Intelligent overclocking tools:
- ASUS AI Booster utility
Precision Tweaker 2:
- vCore: Adjustable CPU voltage at 0.00625V increment
- vDIMM: 64-step DRAM voltage control
- vChipset (N.B.): 33-step Chipset voltage control
- vFSB Termination: 15-step reference voltage control
- vCPU PLL: 64-step CPU PLL voltage control
SFS (Stepless Frequency Selection)
- FSB tuning from 200MHz up to 800MHz at 1MHz
increment
- Memory tuning from 800MHz up to 3200MHz
- PCI Express frequency tuning from 100MHz up to
150MHz at 1MHz increment
Overclocking Protection:
- ASUS C.P.R.(CPU Parameter Recall)
(continued on the next page)
Rear panel
Internal connectors
BIOS features
Manageability
Support DVD contents
Form factor
2 x PS/2 Keyboard port (purple)
1 x Optical S/PDIF Output port
1 x Coaxial S/PDIF Output port
1 x External SATA
1 x LAN (RJ45) port
4 x USB 2.0/1.1 ports
1 x IEEE1394a port
1 x Floppy disk drive connector
3 x USB connectors support additional 6 USB ports
1 x COM connector
1 x CPU / 1 x Power / 2 x Chassis Fan connectors
Front panel audio connector
1 x S/PDIF Out Header
Chassis Intrusion connector
CD audio in
24-pin ATX Power connector
8-pin ATX 12V Power connector
System Panel (Q-Connector)
8 Mb Award BIOS, PnP, DMI2.0, WfM2.0, SM BIOS 2.3,
Multi-Language BIOS
WOL by PME, WOR by PME, Chasis Intrusion, PXE
Drivers
ASUS PC Probe II
ASUS Update
ASUS AI Suite
Anti-virus software (OEM version)
ATX form factor: 12 in x 9.6 in (30.5 cm x 24.5 cm)
*Specifications are subject to change without notice.
xiii
xiv
This chapter describes the motherboard features and the new technologies it supports.
1
introduction
Chapter summary
1
1.2 Package contents ......................................................................... 1-1
ASUS P5N-T Deluxe
1.1 Welcome!
Thank you for buying an ASUS
®
P5N-T Deluxe motherboard!
The motherboard delivers a host of new features and latest technologies, making it another standout in the long line of ASUS quality motherboards!
Before you start installing the motherboard, and hardware devices on it, check the items in your package with the list below.
1.2 Package contents
Check your motherboard package for the following items.
Motherboard
I/O modules
Cables
Accessories
Application DVD
Documentation
1 x 1-port IEEE 1394a module
1 x 2-port USB 2.0 module
1 x Serial ATA power cable for 2 devices
6 x Serial ATA signal cables
1 x Ultra DMA 133/100/66 cable
1 x Floppy disk drive cable
Q-Shield (I/O shield)
1 x ASUS Optional Fans for Water-Cooling or
Passive-Cooling only
1 x 3-in-1 ASUS Q-Connector Kit
(USB, IEEE 1394, system panel; Retail version only)
3 x ASUS SLI Bridges
ASUS motherboard support DVD
User guide
If any of the above items is damaged or missing, contact your retailer.
ASUS P5N-T Deluxe 1-1
1-2
1.3 Special features
1.3.1 Product highlights
Intel
®
Core™ 2 Quad Processor Ready
the latest Intel
®
Core™ 2 Quad processors in the
LGA775 package. It is excellent for multi-tasking, multi-media and enthusiastic gamers with 1066 / 800 MHz FSB. The Intel the most powerful CPUs in the world. This motherboard also supports Intel in the new 45 nm manufacturing process.
®
Quad processor is one of
Intel
®
CPUs
Intel
®
Core™2 Duo/ Intel
®
Core™2 Extreme CPU support
This motherboard supports the latest Intel
®
Core™2 processor in the LGA775 package. With the new Intel
®
Core™ microarchitecture technology and 1600 / 1333
/ 1066 / 800 MHz FSB, the Intel
®
Core™2 is one of the most powerful and energy efficient CPUs in the world.
NVIDIA
®
nForce
®
780i SLI chipset
The NVIDIA
®
nForce 780i SLI chipset supports the NVIDIA
®
Scalable Link Interface
(SLI™) technology that allows three graphics processing units (GPUs) in a single system. It’s designed for enthusiast, extreme overclocking capability, ultimate gaming performance with SLI technology support. It’s definitely one of the fastest platform in the world. The NVIDIA
®
nForce 780i SLI chipset also supports six
(6) Serial ATA 3 Gb/s devices, three PCI Express™ x16 slots with NVIDIA support at full x16, x16, x16 mode, and up to 10 USB 2.0 ports.
®
SLI
™
NVIDIA
®
Scalable Link Interface (SLI™)
NVIDIA SLI™ (Scalable Link Interface) takes advantage of the increased bandwidth of the PCI Express bus architecture and features intelligent hardware and software that allows two GPUs to efficiently work together to deliver earthshattering, scalable performance.
NVIDIA
®
3-Way SLI™ (Scalable Link Interface)
NVIDIA 3-Way SLI™ (Scalable Link Interface) takes advantage of the increased bandwidth of the PCI Express 2.0 bus architecture and features intelligent hardware and software that allows three GPUs to efficiently work together to deliver earth-shattering, scalable performance. For some applications nearly triple performance!
Chapter 1: Product Introduction
PCIe 2.0
This motherboard supports the latest PCIe 2.0 device for twice the current speed and bandwidth. This enhances system performance while still providing backward compatibility to PCIe 1.0 devices. See page 2-18 for details.
DDR2 memory support
The motherboard supports DDR2 memory that features data transfer rates of
1066/800/667 MHz to meet the higher bandwidth requirements of the latest
3D graphics, multimedia, and Internet applications. The dual-channel DDR2 architecture doubles the bandwidth of your system memory to boost system performance, eliminating bottlenecks with peak bandwidths of up to 12.8 GB/s.
See page 2-13 for details.
Serial ATA 3 Gb/s technology and SATA-On-The-Go
This motherboard supports the next-generation hard drives based on the Serial
ATA (SATA) 3 Gb/s storage specification, delivering enhanced scalability and doubling the bus bandwidth for high-speed data retrieval and saves. The external
SATA port located at the back I/O provides smart setup and hot-plug functions.
Easily backup photos, videos and other entertainment contents to external devices.
See page 2-22 for details.
The NVIDIA
®
MediaShield™ RAID controller integrated in the NVIDIA
®
nForce
®
780i SLI™ chipset allows RAID 0, RAID 1, RAID 10(0+1), RAID 5, and JBOD configurations for six SATA 3 Gb/s connectors. See page 2-24 for details.
IEEE 1394a support
The IEEE 1394a interface provides high speed digital interface for audio/video appliances such as digital television, digital video camcorders, storage peripherals
& other PC portable devices. See pages 2-21 and 2-26 for details.
S/PDIF digital sound ready
This motherboard provides convenient connectivity to external home theater audio systems via coaxial and optical S/PDIF-out (SONY/PHILIPS Digital Interface) jacks. It allows to transfer digital audio without converting to analog format and keeps the best signal quality. See pages 2-21 and 2-22 for details.
ASUS P5N-T Deluxe 1-3
Gigabit LAN solution
PCI Express Gb LAN controller delivers transfer speeds up to ten times faster than conventional 10/100/1000 Ethernet connections. Gigabit LAN is the networking standard for the early future and is ideal for handling large amounts of data such
See page 2-21 for details.
High Definition Audio
Enjoy high-end sound quality on your PC! The onboard 8-channel HD audio (High
Definition Audio, previously codenamed Azalia) CODEC enables high-quality
192KHz/24-bit audio output that simultaneously sends different audio streams to different destinations. You can now talk to your partners on the headphone while playing multi-channel network games. See pages 2-21 and 2-22 for details.
Green ASUS
This motherboard and its packaging comply with the European Union’s Restriction on the use of Hazardous Substances (RoHS). This is in line with the ASUS vision of creating environment-friendly and recyclable products/packaging to safeguard consumers’ health while minimizing the impact on the environment.
1-4
1.3.2 ASUS AI Lifestyle unique features
ASUS Power Saving Solution
ASUS Power Saving solution intelligently and automatically provides balanced computing power and energy consumption.
ASUS EPU
The ASUS EPU utilizes innovative technology to digitally monitor and tune the CPU power supply with improved VR responses in heavy or light loadings. It automatically provides power for higher performance or improve efficiency by 7% when the PC is running low intensity applications. Working together with AI Gear 3, this can help you attain the best possible power efficiency and energy savings up to 58.6% to help save the environment.
Chapter 1: Product Introduction
AI Nap
With AI Nap, the system can continue running at minimum power and noise when you are temporarily away. To wake the system and return to the OS environment, simply click the mouse or press a key.
ASUS Quiet Thermal Solution
ASUS Quiet Thermal solution makes system more stable and enhances the overclocking capability.
ASUS 3rd Generation 8 Phase Power Design
Longer Life, & Higher Efficiency!
With power efficiency so important to operating temperatures, ASUS' 3rd generation 8-phase VRM design leads the industry with its 95% power efficiency. High quality power components such as low RDS (on) MOSFETs for minimum switching loss & lower temperatures, Ferrite core chokes with lower hysteresis loss, and high quality Japanese-made conductive polymer capacitors all add up to ensure longer component life and lower power loss
- creating more energy efficiency.
Fanless Design - Stack Cool 2
ASUS Stack Cool 2 is a fan-less and zero-noise cooling solution that lowers the temperature of critical heat generating components. The motherboard uses a special design on the printed circuit board (PCB) to dissipate heat these critical components generate.
Fanless Design - Pure Copper Heat-pipe
The Heat Pipe design effectively directs the heat generated by the chipsets to the heatsink near the back IO ports, where it can be carried away by existing airflow from CPU fan or bundled optional fan. The purpose of the innovative heat pipe design on this motherboard is that the groundbreaking fanless design does not have lifetime problems as a chipset fan does. Furthermore, it provides options for users to install side-flow fan or passive cooler. The Heat
Pipe design is the most reliable fanless thermal solution to date.
DO NOT uninstall the heat-pipe by yourself. Doing so may bend the tubing and affect the heat dissipation performance.
ASUS P5N-T Deluxe 1-5
1-6
Optional Fan (for Water-Cooling or Passive-Cooling only)
The optional fan is specifically designed to provide sufficient airflow over the
CPU power modules and chipset area when water-cooling or passive-cooling is utilized, ensuring effective heat dissipation for the entire system. See page
2-33 for details.
Q-Fan 2
ASUS Q-Fan2 technology intelligently adjusts both CPU fan and chassis fan speeds according to system loading to ensure quiet, cool and efficient operation.
ASUS Crystal Sound
This feature can enhance speech-centric applications like Skype, online game, video conference and recording.
AI Audio 2
AI Audio 2 creates a virtual center channel that expands the overall sound field without introducing a picket fencing effect. Preserving the dialogue or solo performances with downmixing from multichannels will allow you to experience true-to-life high quality audio.
Noise Filter
This feature detects repetitive and stationary noises (non-voice signals) like computer fans, air conditioners, and other background noises then eliminates it in the incoming audio stream while recording.
ASUS EZ DIY
ASUS EZ DIY feature collection provides you easy ways to install computer components, update the BIOS or back up your favorite settings.
ASUS Q-Shield
The specially designed ASUS Q-Shield provides conductivity to best protect your motherboard against static electricity damage and shields it against
Electronic Magnetic Interference (EMI). Without the usual "fingers" present, this new design is convenient and safe to install.
Chapter 1: Product Introduction
ASUS Q-Connector
ASUS Q-Connector allows you to easily connect or disconnect the chassis front panel cables to the motherboard. This unique module eliminates the trouble of connecting the system panel cables one at a time and avoiding wrong cable connections. See page 2-32 for details.
ASUS O.C. Profile
The motherboard features the ASUS O.C. Profile that allows users to conveniently store or load multiple BIOS settings. The BIOS settings can be stored in the CMOS or a separate file, giving users freedom to share and distribute their favorite settings.
ASUS CrashFree BIOS 3
The ASUS CrashFree BIOS 3 allows users to restore corrupted BIOS data from a USB flash disk containing the BIOS file.
ASUS EZ Flash 2
EZ Flash 2 is a user-friendly BIOS update utility. Simply press the predefined hotkey to launch the utility and update the BIOS without entering the OS.
Update your BIOS easily without preparing a bootable diskette or using an
OS-based flash utility.
ASUS AI Slot Detector
When PCIE/PCI devices are installed, you can find out if they are installed successfully via ASUS’s innovatively designed on-board LEDs when they switch on the power. This provides an efficient way to identify the correct way to set up without entering the operating system.
ASUS MyLogo3™
This feature allows you to convert your favorite photo into a 256-color boot logo for a more colorful and vivid image on your screen.
ASUS Multi-language BIOS
The multi-language BIOS allows you to select the language of your choice from the available options. The localized BIOS setup menu helps you configure your system easier and faster.
ASUS P5N-T Deluxe 1-7
1.3.3 ASUS Intelligent Performance and Overclocking features
AI Booster
The ASUS AI Booster allows you to overclock the CPU speed in Windows environment without the hassle of booting the BIOS.
Precision Tweaker 2
Allows the user to adjust the NB Voltage, FSB termination Voltage, CPU PLL
Voltage and the DRAM Voltage in 0.02v steps to finetune voltages to achieve the most precise setting for the ultimate customized overclocking configuration.
C.P.R. (CPU Parameter Recall)
The C.P.R. feature of the motherboard BIOS allows automatic re-setting to the
BIOS default settings in case the system hangs due to overclocking. When the system hangs due to overclocking, C.P.R. eliminates the need to open the system chassis and clear the RTC data. Simply shut down and reboot the system, and the
BIOS automatically restores the CPU default setting for each parameter.
1-8 Chapter 1: Product Introduction
This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
2
information
Chapter summary
2
2.1 Before you proceed ..................................................................... 2-1
2.2 Motherboard overview ................................................................. 2-2
2.3 Central Processing Unit (CPU) ................................................... 2-6
2.4 System memory ......................................................................... 2-13
2.5 Expansion slots .......................................................................... 2-16
ASUS P5N-T Deluxe
2.1 Before you proceed
Take note of the following precautions before you install motherboard components or change any motherboard settings.
• Unplug the power cord from the wall socket before touching any component.
• Use a grounded wrist strap or touch a safely grounded object or a metal object, such as the power supply case, before handling components to avoid damaging them due to static electricity.
• Hold components by the edges to avoid touching the ICs on them.
• Whenever you uninstall any component, place it on a grounded antistatic pad or in the bag that came with the component.
• Before you install or remove any component, ensure that the ATX power supply is switched off or the power cord is detached from the power supply. Failure to do so may cause severe damage to the motherboard, peripherals, and/or components.
Onboard LED
The motherboard comes with a standby power LED. The green LED lights up to indicate that the system is ON, in sleep mode, or in soft-off mode. This is a reminder that you should shut down the system and unplug the power cable before removing or plugging in any motherboard component. The illustration below shows the location of the onboard LED.
®
P5N-T DELUXE Onboard LED
ON
Power
SB_PWR
OFF
Off
ASUS P5N-T Deluxe 2-1
2-2
2.2 Motherboard overview
Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it.
Make sure to unplug the power cord before installing or removing the motherboard. Failure to do so can cause you physical injury and damage motherboard components.
2.2.1 Placement direction
When installing the motherboard, make sure that you place it into the chassis in the correct orientation. The edge with external ports goes to the rear part of the chassis as indicated in the image below.
2.2.2 Screw holes
Place nine (9) screws into the holes indicated by circles to secure the motherboard to the chassis.
DO NOT overtighten the screws! Doing so can damage the motherboard.
Place this side towards the rear of the chassis
®
Chapter 2: Hardware information
2.2.3 Motherboard layout
24.5cm (9.6in)
EATX12V
KBMS
CPU_FAN
COM1
USB34
SPDIF_O12
F_ESATA
LAN1_USB12
AUDIO
Marvell
®
88SE6111
Marvell ®
88SE1116
AD1988B
AAFP
LGA775
EPU
NVIDIA nForce
®
®
200
CHA_FAN1
PCIEX16_1
NVIDIA nForce ®
®
780i SLI™
PCIEX1_1
PCIEX16_2
PCI1
PCIEX16_3
PCIEX1_2
CD
IE1394_2
®
NVIDIA
®
570 SLI™
SATA56
SATA34
SATA12
Lithium Cell
CMOS Power
USB910 USB78
BIOS
CHASSIS
USB56
SB_PWR
PANEL
Refer to 2.7 Connectors for more information about rear panel connectors and internal connectors.
ASUS P5N-T Deluxe 2-3
2-4
2.2.4 Layout contents
Slots
1.
2.
3.
4.
DDR2 DIMM slots
PCI slot
PCI Express x 1 slots
PCI Express 2.0 x16 slots
Jumper
1. Clear RTC RAM (3-pin CLRTC)
12.
13.
14.
15.
8.
9.
10.
11.
4.
5.
6.
7.
Rear panel connectors
1. PS/2 mouse port (green)
2.
3.
Coaxial S/PDIF Out port
IEEE 1394a port
LAN (RJ-45) port
Center/Subwoofer port (orange)
Rear Speaker Out port (black)
Line In port (light blue)
Line Out port (lime)
Microphone port (pink)
Side Speaker Out port (gray)
USB 2.0 ports 1 and 2
External SATA port
USB 2.0 ports 3 and 4
Optical S/PDIF Out port
PS/2 keyboard port (purple)
Page
2-13
2-18
2-18
2-18
Page
2-20
2-21
2-22
2-22
2-22
2-22
2-22
2-22
Page
2-21
2-21
2-21
2-21
2-21
2-21
2-21
2-22
Chapter 2: Hardware information
4.
5.
6.
7.
Internal connectors
1. Floppy disk drive connector (34-1 pin FLOPPY)
2.
3.
IDE connector (40-1 pin PRI_IDE))
Serial ATA connectors (7-pin SATA1-6)
USB connectors (10-1 pin USB56, USB78, USB910)
IEEE 1394a port connector (10-1 pin IE1394_2)
Serial port connector (10-1 pin COM1)
CPU, chassis, power, and optional fan connectors
(4-pin CPU_FAN, 3-pin CHA_FAN1-2, 3-pin PWR_FAN)
8.
9.
10.
11.
12.
13.
Chassis intrusion connector (4-1 pin CHASSIS)
ATX power connectors (24-pin EATXPWR, 2 x 4-pin EATX12V)
Front panel audio connector (10-1 pin AAFP)
Optical drive audio connector (4-pin CD)
System panel connector (20-8 pin PANEL)
ASUS Q-Connector (system panel)
2-28
2-28
2-30
2-30
2-31
2-32
Page
2-23
2-23
2-24
2-25
2-26
2-26
2-27
ASUS P5N-T Deluxe 2-5
2.3 Central Processing Unit (CPU)
The motherboard comes with a surface mount LGA775 socket designed for the Intel
®
Core
™
2 Quad / Core
™
2 Extreme / Core
™
2 Duo / Pentium
®
Extreme /
Pentium
®
D/ Pentium
®
4 processors.
• Make sure that all power cables are unplugged before installing the CPU.
• If installing a dual-core CPU, connect the chassis fan cable to the
CHA_FAN1 connector to ensure system stability.
• Due to the chipset limitation, we recommend you use FSB 800MHz CPU or above.
• Upon purchase of the motherboard, make sure that the PnP cap is on the socket and the socket contacts are not bent. Contact your retailer immediately if the PnP cap is missing, or if you see any damage to the PnP cap/socket contacts/motherboard components. ASUS will shoulder the cost of repair only if the damage is shipment/transit-related.
• Keep the cap after installing the motherboard. ASUS will process Return
Merchandise Authorization (RMA) requests only if the motherboard comes with the cap on the LGA775 socket.
• The product warranty does not cover damage to the socket contacts resulting from incorrect CPU installation/removal, or misplacement/loss/ incorrect removal of the PnP cap.
2-6 Chapter 2: Hardware information
2.3.1 Installing the CPU
To install a CPU:
1. Locate the CPU socket on the motherboard.
®
P5N-T DELUXE CPU Socket 775
Before installing the CPU, make sure that the socket box is facing towards you and the load lever is on your left.
2. Press the load lever with your thumb (A), then move it to the left (B) until it is released from the retention tab.
Retention tab
Load lever
A
PnP cap
B
This side of the socket box should face you.
To prevent damage to the socket pins, do not remove the PnP cap unless you are installing a CPU.
3. Lift the load lever in the direction of the arrow to a 135º angle.
ASUS P5N-T Deluxe 2-7
4. Lift the load plate with your thumb and forefinger to a 100º angle (A), then push the PnP cap from the load plate window to remove (B).
B
A
Load plate
Alignment key
5. Position the CPU over the socket, making sure that the gold triangle is on the bottom-left corner of the socket then fit the socket alignment key into the
CPU notch.
CPU notch
Gold triangle mark
The CPU fits in only one correct orientation. DO NOT force the CPU into the socket to prevent bending the connectors on the socket and damaging the CPU!
2-8
6. Close the load plate (A), then push the load lever (B) until it snaps into the retention tab.
7. If installing a dual-core CPU, connect the chassis fan cable to the CHA_FAN1 connector to ensure system stability.
B
A
The motherboard supports Intel
®
LGA775 processors with the Intel
®
Enhanced
Memory 64 Technology (EM64T), Enhanced Intel SpeedStep
®
Technology
(EIST), and Hyper-Threading Technology. Refer to the Appendix for more information on these CPU features.
Chapter 2: Hardware information
2.3.2 Installing the CPU heatsink and fan
The Intel
®
LGA775 processor requires a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance.
• When you buy a boxed Intel
®
processor, the package includes the CPU fan and heatsink assembly. If you buy a CPU separately, make sure that you use only Intel
®
-certified multi-directional heatsink and fan.
• Your Intel
®
LGA775 heatsink and fan assembly comes in a push-pin design and requires no tool to install.
• If you purchased a separate CPU heatsink and fan assembly, make sure that you have properly applied Thermal Interface Material to the CPU heatsink or CPU before you install the heatsink and fan assembly.
Make sure that you have installed the motherboard to the chassis before you install the CPU fan and heatsink assembly.
To install the CPU heatsink and fan:
1. Place the heatsink on top of the installed CPU, making sure that the four fasteners match the holes on the motherboard.
Orient the heatsink and fan assembly such that the CPU fan cable is closest to the CPU fan connector.
Narrow end of the groove
Make sure to orient each fastener with the narrow end of the groove pointing outward. (The photo shows the groove shaded for emphasis.)
ASUS P5N-T Deluxe 2-9
2-10
2. Push down two fasteners at a time in a diagonal sequence to secure the heatsink and fan assembly in place.
A
A B
B
B
A
B A
3. Connect the CPU fan cable to the connector on the motherboard labeled
CPU_FAN.
CPU_FAN
®
P5N-T DELUXE CPU fan connector
Do not forget to connect the CPU fan connector! Hardware monitoring errors can occur if you fail to plug this connector.
Chapter 2: Hardware information
2.3.3 Uninstalling the CPU heatsink and fan
To uninstall the CPU heatsink and fan:
1. Disconnect the CPU fan cable from the connector on the motherboard.
2. Rotate each fastener counterclockwise.
3. Pull up two fasteners at a time in a diagonal sequence to disengage the heatsink and fan assembly from the motherboard.
A
A B
B A
4. Carefully remove the heatsink and fan assembly from the motherboard.
B
B
A
ASUS P5N-T Deluxe 2-11
2-12
5. Rotate each fastener clockwise to ensure correct orientation when reinstalling.
The narrow end of the groove should point outward after resetting.
(The photo shows the groove shaded for emphasis.)
Narrow end of the groove
Refer to the documentation in the boxed or stand-alone CPU fan package for detailed information on CPU fan installation.
Chapter 2: Hardware information
2.4 System memory
2.4.1 Overview
The motherboard comes with four Double Data Rate 2 (DDR2) Dual Inline Memory
Modules (DIMM) sockets.
A DDR2 module has the same physical dimensions as a DDR DIMM but has a
240-pin footprint compared to the 184-pin DDR DIMM. DDR2 DIMMs are notched differently to prevent installation on a DDR DIMM socket.
The figure illustrates the location of the DDR2 DIMM sockets:
®
P5N-T DELUXE 240-pin DDR3 DIMM sockets
Channel
Channel A
Channel B
Sockets
DIMM_A1 and DIMM_A2
DIMM_B1 and DIMM_B2
2.4.2 Memory configurations
You may install 512 MB, 1 GB, and 2 GB unbuffered non-ECC DDR2 DIMMs into the DIMM sockets.
Mode
DIMM_A1 DIMM_B1
Sockets
DIMM_A2 DIMM_B2
Single-Channel
-
Populated
Dual-channel (1) Populated
Dual-channel (2) Populated
Populated
-
Populated
Populated
-
-
Populated
-
-
-
Populated
ASUS P5N-T Deluxe 2-13
2-14
• You may install varying memory sizes in Channel A and Channel B. The system maps the total size of the lower-sized channel for the dual-channel configuration. Any excess memory from the higher-sized channel is then mapped for single-channel operation.
• Always install DIMMs with the same CAS latency. For optimum compatibility, it is recommended that you obtain memory modules from the same vendor.
• Due to chipset resource allocation, the system may detect less than 8 GB system memory when you installed four 2 GB DDR2 memory modules.
• If you install four 1 GB memory modules, the system may detect less than
3 GB of total memory because of address space allocation for other critical functions. This limitation applies to Windows Vista 32-bit/Windows XP 32-bit version operating system since it does not support PAE (Physical Address
Extention) mode.
• If you install Windows Vista 32-bit/Windows XP 32-bit version operating system, we recommend that you install less than 3GB of total memory.
Notes on memory limitations
• Due to chipset limitation, this motherboard can only support up to
8 GB on the operating systems listed below. You may install a maximum of
2 GB DIMMs on each slot.
64-bit
Windows XP Professional x64 Edition
Windows Vista x64 Edition
Chapter 2: Hardware information
2.4.3 Installing a DIMM
Unplug the power supply before adding or removing DIMMs or other system components. Failure to do so can cause severe damage to both the motherboard and the components.
3
2
DDR2 DIMM notch
To install a DIMM:
1. Unlock a DIMM socket by pressing the retaining clips outward.
2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket.
3. Firmly insert the DIMM into the socket until the retaining clips snap back in place and the DIMM is properly seated.
1
1
Unlocked retaining clip
• A DDR2 DIMM is keyed with a notch so that it fits in only one direction. Do not force a DIMM into a socket to avoid damaging the DIMM.
• The DDR2 DIMM sockets do not support DDR DIMMs. Do not install DDR
DIMMs to the DDR2 DIMM sockets.
2.4.4 Removing a DIMM
To remove a DIMM:
1. Simultaneously press the retaining clips outward to unlock the DIMM.
Support the DIMM lightly with your fingers when pressing the retaining clips. The DIMM might get damaged when it flips out with extra force.
1
2. Remove the DIMM from the socket.
2
DDR2 DIMM notch
1
ASUS P5N-T Deluxe 2-15
2-16
2.5 Expansion slots
In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support.
Make sure to unplug the power cord before adding or removing expansion cards. Failure to do so may cause you physical injury and damage motherboard components.
2.5.1 Installing an expansion card
To install an expansion card:
1. Before installing the expansion card, read the documentation that came with it and make the necessary hardware settings for the card.
2. Remove the system unit cover (if your motherboard is already installed in a chassis).
3. Remove the bracket opposite the slot that you intend to use. Keep the screw for later use.
4. Align the card connector with the slot and press firmly until the card is completely seated on the slot.
5. Secure the card to the chassis with the screw you removed earlier.
6. Replace the system cover.
2.5.2 Configuring an expansion card
After installing the expansion card, configure it by adjusting the software settings.
1. Turn on the system and change the necessary BIOS settings, if any. See
Chapter 4 for information on BIOS setup.
2. Assign an IRQ to the card. Refer to the tables on the next page.
3. Install the software drivers for the expansion card.
When using PCI cards on shared slots, ensure that the drivers support “Share
IRQ” or that the cards do not need IRQ assignments. Otherwise, conflicts will arise between the two PCI groups, making the system unstable and the card inoperable. Refer to the table on the next page for details.
Chapter 2: Hardware information
2.5.3 Interrupt assignments
13
14
16
19
9
10
11
12
9
9
6
8
IRQ
0
1
4
22
23
23
20
20
21
22
Standard function
System timer
Standard 101/102-key or Microsoft Natural Keyboard
Communications Port (COM1)*
Standard floppy disk controller
System CMOS/real-time clock
Microsoft ACPI-compliant system
NVIDIA nForce networking controller #3
NVIDIA nForce networking controller #4
NVIDIA nForce PCI system management
Mass storage controller
PS/2 compatible mouse port
Numeric data processor
Primary IDE channel
NVIDIA GeForce 6600 GT
VIA OHCI compliant IEEE 1394 host controller
NVIDIA nForce 590/570/550 Serial ATA controller
NVIDIA network bus enumerator
NVIDIA network bus enumerator
Standard OpenHCD USB host controller
NVIDIA nForce 590/570/550 Serial ATA controller
Standard Enhanced PCI to USB host controller
NVIDIA nForce 590/570/550 Serial ATA controller
IRQ assignments for this motherboard
PCIEx16_2
PCIEx16_3
PCI Slot
PCIEx1_1
PCIEx1_2
USB 1.1
USB 2.0
LAN
PATA
SATA_1
SATA_2
SATA_3
SATA_RAID
1394
Audio
–
–
A
–
– – shared –
–
–
– shared –
– shared –
– – shared –
– shared – shared
–
– –
– shared –
–
–
–
B
–
– shared
–
–
–
C
–
–
–
–
– shared
– shared –
–
–
–
–
–
–
D
–
–
E
– shared
F
shared
–
–
–
–
–
– shared –
G
–
–
– used
–
–
– shared –
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
– –
–
–
–
–
–
–
–
–
–
–
–
–
–
–
H
–
ASUS P5N-T Deluxe 2-17
2.5.4 PCI slot
The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specifications. Refer to the figure below for the location of the slot.
2.5.5 PCI Express x1 slots
This motherboard supports PCI Express x1 network cards, SCSI cards and other cards that comply with the PCI Express specifications. Refer to the figure below for the location of the slots.
2.5.6 PCI Express 2.0 x16 slots
This motherboard has three PCI Express x16 slots that support PCI Express x16 graphic cards complying with the PCI Express specifications. With three graphics cards installed, the motherboard can enable tri-display. Two (blue slots) of the three
PCI Express x16 slots support PCIe 2.0 devices.
This motherboard supports 3 SLI-ready Express x16 graphics cards that comply with the PCI Express specifications.
2-18
PCI Express x1_2 slot
PCIe 2.0 x16_3 slot (blue, �x16)
PCI slot
PCIe x16_2 slot (black, �x16)
PCI Express x1_1 slot
PCIe 2.0 x16_1 slot (blue, �x16)
Chapter 2: Hardware information
• We recommend that you install a VGA card on the primary (blue) PCI
Express slots, and install any other PCI Express device on the PCI Express slot (black).
• Connect a rear chassis fan to the chassis (CHA_FAN1 or CHA_FAN2) connector when using two (or three) graphics cards for better thermal environment. See page 2-27 for details.
• In single card mode, use either the blue or black slot for PCI Express x16 graphics cards to get better performance.
• In SLI™ mode, we recommend that you use the PCIe 2.0 slots (blue slots) to get better performance.
• We recommend that you provide sufficient power when running NVIDIA
®
SLI™ mode. See page 2-29 for details.
ASUS P5N-T Deluxe 2-19
2-20
2.6 Jumper
1. Clear RTC RAM (3-pin CLRTC)
This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS.
You can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data. The onboard button cell battery powers the RAM data in CMOS, which include system setup information such as system passwords.
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Remove the onboard battery.
3. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3 for about 5~10 seconds, then move the cap back to pins 1-2.
4. Reinstall the battery.
5. Plug the power cord and turn ON the computer.
6. Hold down the <Del> key during the boot process and enter BIOS setup to re-enter data.
®
P5N-T DELUXE Clear RTC RAM
1 2
CLRTC
2 3
Clear RTC
• Make sure to re-enter your previous BIOS settings after you clear the
CMOS.
• You do not need to clear the RTC when the system hangs due to overclocking. For system failure due to overclocking, use the C.P.R. (CPU
Parameter Recall) feature. Shut down and reboot the system so the BIOS can automatically reset parameter settings to default values.
Chapter 2: Hardware information
2.7 Connectors
2.7.1 Rear panel connectors
1 2 3 4 5 6 7 8
15
14 13 12 11 10 9
1. PS/2 mouse port (green). This port is for a PS/2 mouse.
2. Coaxial S/PDIF Out port. This port connects an external audio output device via a coaxial S/PDIF cable.
3. IEEE 1394a port. This 6-pin IEEE 1394a port provides high-speed connectivity for audio/video devices, storage peripherals, PCs, or portable devices.
4. LAN (RJ-45) port. This port allows Gigabit connection to a Local Area
Network (LAN) through a network hub. Refer to the table below for the LAN port LED indications.
LAN port LED indications
Activity/Link Speed LED
Status Description Status
OFF
ORANGE
BLINKING
No link
Linked
Data activity
Description
OFF 10 Mbps connection
ORANGE 100 Mbps connection
GREEN 1 Gbps connection
ACT/LINK
LED
SPEED
LED
LAN port
5. Center/Subwoofer port (orange). This port connects the center/subwoofer speakers.
6. Rear Speaker Out port (black). This port connects the rear speakers in a
4-channel, 6-channel, or 8-channel audio configuration..
7. Line In port (light blue). This port connects the tape, CD, DVD player, or other audio sources.
8. Line Out port (lime). This port connects a headphone or a speaker. In
4-channel, 6-channel, and 8-channel configuration, the function of this port becomes Front Speaker Out.
ASUS P5N-T Deluxe 2-21
2-22
9. Microphone port (pink). This port connects a microphone.
10. Side Speaker Out port (gray). This port connects the side speakers in an
8-channel audio configuration.
Refer to the audio configuration table below for the function of the audio ports in
2, 4, 6, or 8-channel configuration.
Audio 2, 4, 6, or 8-channel configuration
Port
Light Blue
Lime
Pink
Orange
Black
Gray
Headset
2-channel
4-channel 6-channel 8-channel
Line In Line In Line In Line In
Line Out Front Speaker Out Front Speaker Out Front Speaker Out
Mic In
–
–
–
Mic In
–
Rear Speaker Out
–
Mic In
Center/Subwoofer
Rear Speaker Out
–
Mic In
Center/Subwoofer
Rear Speaker Out
Side Speaker Out
11. USB 2.0 ports 1 and 2. These 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices.
12. External SATA port. This port connects to an external a Serial ATA hard disk drive.
The external SATA port supports external Serial ATA 3 Gb/s devices. Longer cables support higher power requirements to deliver signal up to two meters away, and enables improved hotswap function.
When using hot-plug and NCQ, set the J-Micron eSATA/PATA Controller Mode in the BIOS to [AHCI].
DO NOT insert a different connector to the external SATA port.
13. USB 2.0 ports 3 and 4. These 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices.
14. Optical S/PDIF Out port. This port connects an external audio output device via an optical S/PDIF cable.
15. PS/2 keyboard port (purple). This port is for a PS/2 keyboard.
Chapter 2: Hardware information
2.7.2 Internal connectors
1. Floppy disk drive connector (34-1 pin FLOPPY)
This connector is for the provided floppy disk drive (FDD) signal cable. Insert one end of the cable to this connector, then connect the other end to the signal connector at the back of the floppy disk drive.
Pin 5 on the connector is removed to prevent incorrect cable connection when using a FDD cable with a covered Pin 5.
FLOPPY
PIN 1
®
P5N-T DELUXE Floppy disk drive connector
2. IDE connector (40-1 pin PRI_IDE)
The onboard IDE connector is for the Ultra DMA 133/100/66 signal cable.
There are three connectors on each Ultra DMA 133/100/66 signal cable: blue, black, and gray. Connect the blue connector to the motherboard’s IDE connector, then select one of the following modes to configure your device.
PRI_EIDE
®
P5N-T DELUXE IDE connector
PIN 1
Drive jumper setting
Single device Cable-Select or Master
Two devices Cable-Select
Master
Slave
ASUS P5N-T Deluxe
Mode of device(s)
-
Master
Slave
Master
Slave
Cable connector
Black
Black
Gray
Black or gray
2-23
2-24
• Pin 20 on the IDE connector is removed to match the covered hole on the
Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable.
• Use the 80-conductor IDE cable for Ultra DMA 133/100/66 IDE devices.
If any device jumper is set as “Cable-Select,” make sure all other device jumpers have the same setting.
3. Serial ATA connectors (7-pin SATA1-6)
These connectors are for the Serial ATA signal cables for Serial ATA hard disk drives.
If you installed Serial ATA hard disk drives, you can create a RAID 0, RAID
with the onboard NVIDIA
®
MediaShield™ RAID controller.
SATA6 SATA5
SATA4 SATA3
®
P5N-T DELUXE SATA connectors
SATA2 SATA1
The RAID function of these connectors is set to [Disabled] by default. If you intend to create a Serial ATA RAID set using these connectors, enable the RAID
Enabled item under the Serial ATA Configuration sub-menu in the BIOS.
These connectors support Native Command Queuing (NCQ), Power
Management (PM) Implementation Algorithm, Hot Swap and smart setup.
Chapter 2: Hardware information
Right-angle side
Connect the right-angle side of SATA signal cable to the SATA device, or connect the right-angle side of the
SATA cable to the onboard SATA port to avoid mechanical conflict with huge graphics cards.
4. USB connectors (10-1 pin USB56, USB78, USB910)
These connectors are for USB 2.0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.0 specification that supports up to 480 Mbps connection speed.
USB910
USB+5V USB_P10- USB_P10+ GND NC
USB78
USB+5V USB_P8- USB_P8+ GND NC
USB56
USB+5V USB_P6- USB_P6+ GND NC
®
P5N-T DELUXE USB 2.0 connectors
USB+5V USB_P9- USB_P9+ USB+5V USB_P7- USB_P7+ USB+5V USB_P5- USB_P5+
Never connect a 1394 cable to the USB connectors. Doing so will damage the motherboard!
You can connect the USB cable to ASUS Q-Connector (USB, blue) first, and then install the Q-Connector (USB) to the USB connector onboard.
ASUS P5N-T Deluxe 2-25
5. IEEE 1394a port connector (10-1 pin IE1394_2)
This connector is for a IEEE 1394a port. Connect the IEEE 1394a module cable to this connector, then install the module to a slot opening at the back of the system chassis.
®
IE1394_2
PIN 1
P5N-T DELUXE IEEE 1394a connector
Never connect a USB cable to the IEEE 1394a connector. Doing so will damage the motherboard!
You can connect the 1394 cable to ASUS Q-Connector (1394, red) first, and then install the Q-Connector (1394) to the 1394 connector onboard.
6. Serial port connector (10-1 pin COM1)
This connector is for a serial (COM) port. Connect the serial port module cable to this connector, then install the module to a slot opening at the back of the system chassis.
COM1
PIN 1
2-26
®
P5N-T DELUXE COM port connector
The serial port module is purchased separately.
Chapter 2: Hardware information
7. CPU, chassis, power, and optional fan connectors
(4-pin CPU_FAN, 3-pin CHA_FAN1-2, 3-pin PWR_FAN)
The fan connectors support cooling fans of 1A~2.2A (26.4 W max.) at +12V.
Connect the fan cables to the fan connectors on the motherboard, making sure that the black wire of each cable matches the ground pin of the connector.
CPU_FAN PWR_FAN
Rotation
CHA_FAN1 CHA_FAN2
®
P5N-T DELUXE Fan connectors
DO NOT forget to connect the fan cables to the fan connectors. Insufficient air flow inside the system may damage the motherboard components. These are not jumpers! DO NOT place jumper caps on the fan connectors!
• Only the CPU_FAN, CHA_FAN1 and CHA_FAN2 connectors support the
ASUS Q-FAN 2 feature.
• If you install two VGA cards, we recommend that you plug the rear chassis fan cable to the motherboard connector labeled CHA_FAN1 or CHA_FAN2 for better themal environment.
ASUS P5N-T Deluxe 2-27
8. Chassis intrusion connector (4-1 pin CHASSIS)
This connector is for a chassis-mounted intrusion detection sensor or switch.
Connect one end of the chassis intrusion sensor or switch cable to this connector. The chassis intrusion sensor or switch sends a high-level signal to this connector when a chassis component is removed or replaced. The signal is then generated as a chassis intrusion event.
By default , the pin labeled “Chassis Signal” and “ Ground” are shorted with a jumper cap. Remove the jumper caps only when you intend to use the chassis intrusion detection feature.
2-28
®
CHASSIS
(Default)
P5N-T DELUXE Chassis intrusion connector
9. ATX power connectors
(24-pin EATXPWR, 2 x 4-pin EATX12V)
These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit.
EATX12V EATXPWR
+3 Volts
+12 Volts
+12 Volts
+5V Standby
Power OK
Ground
+5 Volts
Ground
+5 Volts
Ground
+3 Volts
+3 Volts
Ground
+5 Volts
+5 Volts
+5 Volts
Ground
Ground
Ground
PSON#
Ground
-12 Volts
+3 Volts
®
P5N-T DELUXE ATX power connectors
• Make sure to remove the cap on the ATX12V connector before connecting an 8-pin EPS +12V power plug.
• Use only either a 4-pin ATX12V or an 8-pin EPS +12V power plug for the
EATX12V connector.
Chapter 2: Hardware information
• For a fully configured system, we recommend that you use a power supply unit (PSU) that complies with ATX 12V Specification 2.0 (or later version) and provides a minimum power of 550 W.
• Do not forget to connect the 4-pin/8pin EATX12V power plug; otherwise, the system will not boot.
• If you are uncertain about the minimum power supply requirement for your system, refer to the Recommended Power Supply Wattage Calculator at http://support.asus.com/PowerSupplyCalculator/PSCalculator.
aspx?SLanguage=en-us for details.
• Use of a PSU with a higher power output is recommended when configuring a system with more power-consuming devices. The system may become unstable or may not boot up if the power is inadequate.
• If you want to use two or more high-end PCI Express x16 cards, use a PSU with 1000 W power or above to ensure the system stability.
• The ATX12 V Specification 2.0-compliant (500 W) PSU has been tested to support the motherboard power requirement with the following configuration:
Normal Loading
CPU
PSC 3.73G 1066
DDR800
VGA
SATA-HD
ESATA-HD
IDE-HD
CD-ROM
USB
PCI
1GB*2
Nvidia 7800GTX*2
SATA*4
1
2
1
1
1
• If you want to use 3-way SLI™ configuration, visit the NVIDIA website
(www.nvidia.com) for the qualified PSU vendor list.
ASUS P5N-T Deluxe 2-29
2-30
10. Front panel audio connector (10-1 pin AAFP)
This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC`97 audio standard. Connect one end of the front panel audio I/O module cable to this connector.
AAFP
HD Audio-compliant pin definition
Legacy AC ‘97 audio pin definition
®
P5N-T DELUXE Analog front panel connector
• We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard’s high-definition audio capability.
• If you want to connect a high-definition front panel audio module to this connector, set the Front Panel Type item in the BIOS setup to [HD Audio]; if you want to connect an AC'97 front panel audio module to this connector, set the item to [AC'97]. By default, this connector is set to [HD Audio].
11. Optical drive audio connector (4-pin CD)
This connector allows you to receive stereo audio input from sound sources such as a CD-ROM, TV tuner, or MPEG card.
®
CD
(black)
Chapter 2: Hardware information
12. System panel connector (20-8 pin PANEL)
This connector supports several chassis-mounted functions.
• System power LED (2-pin PLED)
This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode.
• Hard disk drive activity LED (2-pin IDE_LED)
This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity
LED cable to this connector. The IDE LED lights up or flashes when data is read from or written to the HDD.
• System warning speaker (4-pin SPEAKER)
This 4-pin connector is for the chassis-mounted system warning speaker. The speaker allows you to hear system beeps and warnings.
• ATX power button/soft-off button (2-pin PWR)
This connector is for the system power button. Pressing the power button turns the system on or puts the system in sleep or soft-off mode depending on the BIOS settings. Pressing the power switch for more than four seconds while the system is ON turns the system OFF.
• Reset button (2-pin RESET)
This 2-pin connector is for the chassis-mounted reset button for system reboot without turning off the system power.
ASUS P5N-T Deluxe 2-31
2-32
13. ASUS Q-Connector (system panel)
You can use the ASUS Q-Connector to connect/disconnect chassis front panel cables in a few steps. Refer to the instructions below to install the ASUS Q-
Connector.
1. Connect the front panel cables to the
ASUS Q-Connector.
Refer to the labels on the Q-Connector to know the detailed pin definitions, then match them to the respective front panel cable labels.
2. Install the ASUS Q-Connector to the system panel connector, making sure the orientation matches the labels on the motherboard.
3. The front panel functions are now enabled.
The figure shows the Q-Connector properly installed on the motherboard.
Chapter 2: Hardware information
2.7.3 Installing the optional fans
Install the optional fan only if you are using a passive cooler or a water cooler.
Installing the optional fan with an active CPU cooler will interfere with the airflow and destabilize the system.
1. Position the fan above the pipe and heatsink assembly.
2. Fit the fan to the grooved edge of the heatsink.
3. Carefully push down the fan until it snugly fits the heatsink, then connect the fan cable.
4. The photo shows the fan installed on the motherboard.
• Plug the optional fan cable to the CHA_FAN1, CHA_FAN2 or PWR_FAN connector on the motherboard.
• Make sure the optional fan is installed correctly to prevent damage to the fan and motherboard components.
• We strongly recommend that you install the optional fan when using a passive cooler or a water cooler.
ASUS P5N-T Deluxe 2-33
2-34 Chapter 2: Hardware information
This chapter describes the power up sequence, the vocal POST messages, and ways of shutting down the system.
Chapter summary
3
3.1 Starting up for the first time ........................................................ 3-1
3.2 Turning off the computer ............................................................. 3-2
ASUS P5N32-E SLI
3.1 Starting up for the first time
1. After making all the connections, replace the system case cover.
2. Be sure that all switches are off.
3. Connect the power cord to the power connector at the back of the system chassis.
4. Connect the power cord to a power outlet that is equipped with a surge protector.
5. Turn on the devices in the following order: a. Monitor b. External SCSI devices (starting with the last device on the chain) c. System power
6. After applying power, the system power LED on the system front panel case lights up. For systems withATX power supplies, the system LED lights up when you press the ATX power button. If your monitor complies with “green” standards or if it has a “power standby” feature, the monitor LED may light up or switch between orange and green after the system LED turns on.
The system then runs the power-on self tests or POST. While the tests are running, the BIOS beeps (see BIOS beep codes table below) or additional messages appear on the screen. If you do not see anything within 30 seconds from the time you turned on the power, the system may have failed a power-on test. Check the jumper settings and connections or call your retailer for assistance.
7. At power on, hold down the <Delete> key to enter the BIOS Setup. Follow the instructions in Chapter 4.
3-1
3.2 Turning off the computer
3.2.1 Using the OS shut down function
If you are using Windows ® XP:
1. Click the Start button then select Turn Off Computer.
2. Click the Turn Off button to shut down the computer.
3. The power supply should turn off after Windows ® shuts down.
If you are using Windows
®
Vista:
1. Click the Start button then select ShutDown.
2. The power supply should turn off after Windows ® shuts down.
3.2.2 Using the dual function power switch
While the system is ON, pressing the power switch for less than four seconds puts the system to sleep mode or to soft-off mode, depending on the BIOS setting.
Pressing the power switch for more than four seconds lets the system enter the soft-off mode regardless of the BIOS setting. Refer to section 4.5 Power Menu in
Chapter 4 for details.
3-2 Chapter 3: Powering up
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 25 Welcome!
- 25 Package contents
- 25 Special features
- 25 Product highlights
- 25 ASUS AI Lifestyle unique features
- 25 and Overclocking features
- 26 Before you proceed
- 26 Motherboard overview
- 26 Placement direction
- 26 Screw holes
- 26 Motherboard layout
- 26 Layout contents
- 26 Central Processing Unit (CPU)
- 26 Installing the CPU
- 26 Installing the CPU heatsink and fan
- 26 Uninstalling the CPU heatsink and fan
- 26 System memory
- 26 Overview
- 26 Memory configurations
- 26 Installing a DIMM
- 26 Removing a DIMM
- 26 Expansion slots
- 26 Installing an expansion card
- 26 Configuring an expansion card
- 26 Interrupt assignments
- 26 PCI slot
- 26 PCI Express x1 slots
- 26 PCI Express 2.0 x16 slots
- 30 Jumper
- 30 Connectors
- 30 Rear panel connectors
- 30 Internal connectors
- 30 Installing the optional fans
- 31 Starting up for the first time
- 31 Turning off the computer
- 31 Using the OS shut down function
- 31 Using the dual function power switch
- 32 Managing and updating your BIOS
- 32 ASUS Update utility
- 32 Creating a bootable floppy disk
- 32 ASUS EZ Flash 2 utility
- 32 Updating the BIOS
- 32 Saving the current BIOS file
- 32 ASUS CrashFree BIOS 3 utility
- 32 BIOS setup program
- 32 BIOS menu screen
- 32 Menu bar
- 32 Legend bar
- 32 Menu items
- 32 Sub-menu items
- 32 Configuration fields
- 32 Pop-up window
- 32 General help
- 32 Main menu
- 32 System Time [xx:xx:xx]
- 32 System Date [Day xx/xx/xxxx]
- 32 Language [English]
- 32 Legacy Diskette A [1.44M, 3.5 in.]
- 32 Primary IDE Master/Slave