- Computers & electronics
- Computer components
- Chassis components
- Mounting kits
- Metra
- 99-7422
- Specification
advertisement
INSTALLATION INSTRUCTIONS FOR PART 99-7422
APPLICATIONS
Nissan Sentra
2007-2010
99-7422
KIT FEATURES
• DIN Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
A) Radio Housing • B) Radio Housing Trimplate • C) Radio Housing Brackets
• D) Double DIN Trim Plate • E) (2) Carriage Bolts • F) (2) Nuts
A
B
C D
E
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• 70-7552 - Nissan harness 2007-up
• NIRD-01 - Nissan display and Bluetooth retention harness 2007-08
Antenna Adapter:
• 40-NI12 - Nissan antenna adapter 2007-up
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • Hook Tool • Socket Set
F
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION
99-7422
TABLE OF CONTENTS
Dash Disassembly
- Nissan Sentra 2007 -2010 . . . . . . . . . . . . . . . . . . . . . . .
. . . . 1,2
Kit Assembly
- Kit Preparation (For DIN radio with pocket only) . . . . . . . . . . . . . . . . . 3
- DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
- Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
- Stacked ISO Mount Units Provision . . .. . . . . . . . . . . . . . . . . . . . . . . . 6
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
*Note:
Refer also to the instructions included with the aftermarket radio.
99-7422 DASH DISASSEMBLY
NISSAN SENTRA 2007-2010
A
1 Disconnect the negative battery terminal to prevent an accidental short circuit.
1 2 3
2 Push down on the collar below the shift knob to unclip. Using a small screwdriver or hook tool remove the spring clip to release and remove the shift knob. (Figure A)
3 Unclip and remove shifter trim panel around shifter. (Figure B)
B
4 Unclip and remove the a/c control panel. (Figure C)
LO cc
HI
5 Remove (2) Phillips screws securing the bottom of the radio trim panel.
(Figure D)
D
SEEK
POWER
TUNE
C
SEEK
POWER
TUNE
PASS AIRBAG
LO cc
HI LO cc
HI
1
99-7422 DASH DISASSEMBLY
NISSAN SENTRA 2007-2010
E
6 Unclip and remove the trim panel at the top of the radio trim panel.
(Figure E)
7 Remove (2) Phillips screws securing the top of the radio trim panel.
(Figure F)
8 Unplug and remove radio/trim panel assembly. (Figure G)
9 Remove (4) Phillips screws securing the radio brackets to the trim panel and remove the trim panel.
10 Remove (6) Phillips screws (3 per side) securing the factory brackets to the radio/display assembly. (Retain the factory brackets and display for possible use during kit assembly.)
Continue to kit assembly.
F
SEEK
POWER
POWER
SEEK TUNE
TUNE
G
SEEK
POWER
TUNE
2
99-7422 KIT ASSEMBLY
KIT PREPARATION
(FOR DIN RADIO WITH POCKET ONLY)
* Note: Refer also to the instructions included with the aftermarket radio.
A
1 Attach the (2) radio housing brackets to the radio housing using the supplied
(2) carriage bolts and nuts. (Figure A)
2 Secure the display* into the assembled radio housing/bracket assembly using the factory hardware. (Figure B)
*NOTE: Display can be replaced with
Metra’s Pocket, Part number 88-00-
7422 sold separately.
Continue to final assembly.
B
3
99-7422 KIT ASSEMBLY
DIN RADIO PROVISION WITH POCKET
* Note: Refer also to the instructions included with the aftermarket radio.
A
1 Slide the DIN cage into the Radio
Housing and secure by bending the metal locking outward. (Figure A)
2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B)
3 Attach the radio housing trim plate supplied with the kit. (Figure B)
NOTE: Display can be replaced with
Metra’s Pocket, Part number 88-00-
7422 sold separately.
Continue to final assembly.
B
4
99-7422 KIT ASSEMBLY
DOUBLE DIN RADIO PROVISION
* Note: Refer also to the instructions included with the aftermarket radio.
A
1 Re-Secure the display* to the factory brackets using the factory hardware.
(Figure A)
2 Slide the Double DIN radio into the factory brackets and secure the unit to the brackets using the screws supplied with the radio. (Figure B)
3 Place the Double DIN trim plate over the face of the aftermarket radio.
(Figure B)
*NOTE: Display can be replaced with
Metra’s Pocket, Part number 88-00-
7422 sold separately.
Continue to final assembly.
B
5
99-7422 KIT ASSEMBLY
STACKED ISO MOUNT UNITS PROVISION
* Note: Refer also to the instructions included with the aftermarket radio.
1 Re-Secure the display* to the factory brackets using the factory hardware.
(Figure A)
2 Slide the stacked ISO Mount units into the factory bracket/display assembly and secure the units to the assembly using the screws supplied with the units. (Figure B)
3 Place the Double DIN trim plate over the face of the units. (Figure B)
*NOTE: Display can be replaced with
Metra’s Pocket, Part number 88-00-
7422 sold separately.
Continue to final assembly.
A
B
6
99-7422 FINAL ASSEMBLY
FINAL ASSEMBLY
A
B
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
C
D
1
2
3
Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer . . . . . . . . . . . . . . . . . Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
7
99-7422
NOTES
8
99-7422
NOTES
9
99-7422 INSTRUCTIONS
1-800-221-0932 www.metraonline.com
REV. 04/21/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-7422
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project