WP-PN2O

HONDA PIONEER 500 OVERHEAD AUDIO SYSTEM

Tools Needed For Installation

#3 Phillips Head Screwdriver

Wire Crimpers / Strippers

Wrench for battery terminals

Thread Locker

Figure 1 Figure 2

Figure 3 Figure 4

Figure 5

1) From the underside of the cage, place the rear of the enclosure in first, then push the front up in to place. (Figure 1 & 2)

2) While holding the enclosure in place, put one of the rear brackets on top of the enclosure and using the screws provided. Loosely screw into the threaded insert on the enclosure. (Figure 3 & 4) (It is recommended to use Loc-Tight or another type of thread locker to prevent the screws from loosening)

3) Repeat for the remaining brackets.

4) Center the unit in the cage. While pressing the brackets in to the cage tighten the screws.

5) The installation of the enclosure portion is now complete, Step 6 begins the wiring.

Figure 6

Figure 7

Figure 8 Figure 9 Figure 10

6) Using the cable ties provided run the power/ground cable down the rear passenger side to the battery located under the passenger seat. (Figure 6)

7) Cut the power/ground cable to length, be sure to leave enough wire at the battery location to wire to the battery, strip back approximately 4 inches of the black tubing to expose the red/black wires inside. (Figure 7)

8) Strip back 1/4"-1/2" of wire to make your connections. (Figure 8)

9) Crimp the supplied fuse holder onto the end of the RED wire and attach to the battery "+" terminal.

(Figure 9)

10) Crimp the supplied ring terminal to the BLACK wire and attach to the battery "-" terminal. (Figure 10)

Your connections are now complete, refer to the user guide for proper use of the system.

Contents:

1 – PN2O Enclosure

4 - 3mm Brackets

16 - M6 x 1.0 Stainless Machine screws

16 – Stainless washers

1 – Fuse Holder

1 – Crimp On Ring Terminal

5 – Zip Ties

CORPORATE: SSV WORKS, 201 N RICE AVE STE A, OXNARD, CA 93030

WEB: www.SSVworks.com PHONE: 818-991-1778

SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030 www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751

** Do not cut or modify any connectors **

When installing your SSV Works WP

Series overhead system, the following wires will be coming out of the harness:

1

2

3

1. Audio Output

Harness

2. Power / Ground

3. Antenna

4. Secondary Speaker

Harness

4

1. This wire harness will run down the vehicles cage and have a 4 pin connector at the bottom, this harness is an audio output and amplifier turn on. This is to add a SSV Works Powered 10” Subwoofer directly to your overhead system. Please visit our website www.ssvworks.com

for complete applications. To add a standard amplifier to power additional speakers you will need to purchase SSV Works part #WP-HRCA.

2. Power / Ground wire harness, run this to the battery and connect per the included instructions.

WP SERIES POWERED SUBWOOFERS

POLARIS RZR XP 1000 & XP4 1000

- WP-RZ3BSS10 (behind seat)

POLARIS RZR XP 1000, XP 4 1000/

TURBO/900 EPS

- WP-RZ3GBS10 (glove box)

POLARIS RANGER 2015+

- WP-RG3S10

POLARIS RANGER

- WP-RG2S10

POLARIS RZR, RZR4 & Jagged X 900

- WP-RZS10

CAN-AM COMMANDER & MAVERICK

- WP-CM2S10

3. External antenna, run this along the top of the cage (away from the power/ground) keep this high in the vehicle for increased

FM reception.

4. Certain units have the ability to add additional speakers. There will be a short 2-3" harness out of the main grommet with a 4 pin connector, this will plug into the SSV Works WP additional speaker add-on.

YAMAHA RHINO

- WP-RHS10

HONDA PIONEER 700

- WP-PNS10

HONDA PIONEER 500

- WP-PN2S10

KAWASAKI TERYX

- WP-TXS10

KAWASAKI TERYX

- WP-TX2S10 (2-seat Teryx )

ARCTIC CAT WILDCAT

TRAIL / SPORT

- WP-WC2S10

SSV Works # WP-HRCA

(Sold Separately)

© 2016 SSV WORKS WP-HRCA Rev. 2 2-3-16