Chief QMP1MB Installation Instructions


Add to my manuals
8 Pages

advertisement

Chief QMP1MB Installation Instructions | Manualzz

I N S T A L L A T I O N I N S T R U C T I O N S

Mobile Base Music Stand

QMP1MB

Installation Instructions

DISCLAIMER

Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies.

All rights reserved.

QMP1MB

WARNING:

Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided.

WARNING:

Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment.

Reinforce the structure as required before installing the component.

WARNING:

Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components on the stand does not exceed 150 lbs (68.04 kg).

IMPORTANT WARNINGS AND

CAUTIONS!

WARNING:

A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION:

A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.

DIMENSIONS

DIMENSIONS: [MILLIMETERS]

INCHES

2

QMP1MB

LEGEND

Tighten Fastener

Apretar elemento de fijación

Befestigungsteil festziehen

Apertar fixador

Serrare il fissaggio

Bevestiging vastdraaien

Serrez les fixations

Loosen Fastener

Aflojar elemento de fijación

Befestigungsteil lösen

Desapertar fixador

Allentare il fissaggio

Bevestiging losdraaien

Desserrez les fixations

Phillips Screwdriver

Destornillador Phillips

Kreuzschlitzschraubendreher

Chave de fendas Phillips

Cacciavite a stella

Kruiskopschroevendraaier

Tournevis à pointe cruciforme

Open-Ended Wrench

Llave de boca

Gabelschlüssel

Chave de bocas

Chiave a punte aperte

Steeksleutel

Clé à fourche

By Hand

A mano

Von Hand

Com a mão

A mano

Met de hand

À la main

Hex-Head Wrench

Llave de cabeza hexagonal

Sechskantschlüssel

Chave de cabeça sextavada

Chiave esagonale

Zeskantsleutel

Clé à tête hexagonale

3

Installation Instructions

Adjust

Ajustar

Einstellen

Ajustar

Regolare

Afstellen

Ajuster

Remove

Quitar

Entfernen

Remover

Rimuovere

Verwijderen

Retirez

Pencil Mark

Marcar con lápiz

Stiftmarkierung

Marcar com lápis

Segno a matita

Potloodmerkteken

Marquage au crayon

Drill Hole

Perforar

Bohrloch

Fazer furo

Praticare un foro

Gat boren

Percez un trou

Optional

Opcional

Optional

Opcional

Opzionale

Optie

En option

Security Wrench

Llave de seguridad

Sicherheitsschlüssel

Chave de segurança

Chiave di sicurezza

Veiligheidssleutel

Clé de sécurité

Installation Instructions

TOOLS REQUIRED FOR INSTALLATION

PARTS

3/16"

(included)

A (1)

[Left leg]

F (1)

[Cross bracket]

J (4)

5/16-18 x 3/4"

K (4)

5/16-18 x 2-3/4"

B (1)

[Right leg]

C (4)

[Snap-on cover]

E (1)

[Upright]

D (2)

[End cap]

G (1)

3/16"

[Drill bit]

H (1)

3/16"

M (4)

5/16"

L (4)

5/16-18 x 4-1/4"

QMP1MB

4

Installation Instructions

ASSEMBLY

CAUTION:

Attachment holes may be damaged if a power drill is used to insert button head cap screws. Screws should first be inserted and turned BY HAND with the hex key or with a handheld screwdriver BEFORE using the hex head drill bit

(G) and power drill to complete the attachment.

1.

Assemble two legs (A) and (B) to the stand cross bracket (F) using two 5/16-18 x 4-1/4" button head cap screws (L) through one end cap (D) per leg. (See Figure 1)

(L) x 4

Cable

Tie inner column

QMP1MB

(B)

(F)

Figure 2

NOTE:

Insert and turn screws in order shown (1, 2, 3, 4). (See

Figure 3)

(Front view of stand)

(A)

Figure 1

(D) x 2

1

3

4

2

CAUTION:

INNER COLUMN IS SHIPPED DISENGAGED and may pinch hands! Hold both inner column and outer upright while removing from box.

IMPORTANT ! : Press cable tie tab to loosen and remove cable tie from around knob post. (See Figure 2)

NOTE:

Disengage knob on upright BEFORE attaching base to the upright.

2.

Lift up slightly on the inner column of upright and hold firmly toward top of upright. (See Figure 2)

3.

Pull out knob on the upright and turn 90° in either direction to disengage the locking mechanism. (See Figure 2)

4.

Raise the inner column and turn the knob 90° in either direction to engage the knob and lock the column in place.

(See Figure 2)

(Bottom view of stand)

Figure 3

5.

Attach upright (E) to leg assembly using four 5/16-18 x 2-3/

4" button head cap screws (K) and four 5/16" washers (M).

(See Figure 3) and (See Figure 4)

(Front view of stand)

(E)

(K) x 4

(M) x 4

Figure 4

5

QMP1MB

Attaching Accessories to Mobile Stand

WARNING:

EXCEEDING MAXIMUM WEIGHT CAPACITY

MAY LEAD TO SERIOUS PERSONAL INJURY OR

DAMAGE TO EQUIPMENT! It is the installer’s responsibility to ensure the total amount of weight placed on the stand does not exceed 150 lbs (68.04 kg).

CAUTION:

Before attaching accessories to stand set the brakes on the back wheels by pressing down on the tab.

(See Figure 5)

1.

Attach accessory and component(s) to stand following instructions included with the accessory.

Press down to set brakes

Figure 5

Adjusting Stand Height

CAUTION:

ALWAYS remove components attached to accessories BEFORE adjusting the height of stand.

1.

Firmly grasp top of inner column. (See Figure 6)

IMPORTANT ! : Firmly grasp at the top of the inner column when adjusting stand height. (See Figure 6)

Do NOT let accessory rest here

2

Inner

Column

3

Installation Instructions

Figure 7

IMPORTANT ! :

Set the height of the stand so the accessories do NOT rest on the upper part of the outer column.

(See Figure 7) Always set the height so the knob is engaged in a hole in the inner column.

Cable Management

1.

Signal cables can be run down the front flap of the upright and out the front of the upright at any of the openings.

(See Figure 8)

2.

Any accessory power cords can be run through the front and down through the upright to exit out the back. (See

Figure 8)

3.

Install the snap-on covers (C) to any opening that is not being used. (See Figure 8)

4.

To remove the snap-on covers, grip the sides of the cover in the middle and pull off. They can also be removed by inserting a flat-blade screwdriver into the bottom slot and rotating the screwdriver.

(Front view of column)

2

1

(Rear view of column)

Grasp top of inner column (within shaded area) when adjusting stand height

Figure 6

2.

Adjust the stand to the desired height by slightly lifting the accessory, pulling out knob on the center post and turning

90 o

in either direction to disengage the locking mechanism.

(See Figure 7)

3.

Raise or lower the upright, then turn the knob 90 o

either direction to engage the knob and lock the stand at desired height. (See Figure 7)

6

Exits for signal cables

3

(C)

Figure 8

Exit for power cables

Installation Instructions

Stand Use and Maintenance

CAUTION:

This stand is intended for use only with the products and maximum weight indicated (150 lbs [68.04 kg]).

Use with other products or products heavier than the maximum weight indicated may result in instability causing possible injury.

WARNING:

STAND CAN TIP OVER RESULTING IN RISK

OF INJURY. Move stand slowly. Apply moving force on narrow dimension. Never apply force at top - always push near middle. Push, don’t pull.

Do NOT push stand near top

Push stand near middle

QMP1MB

Figure 10

x 4

Figure 9

1.

Always place stand on level surface.

2.

Always lock the wheels when the stand is not moving.

3.

Check and tighten the hex nuts on the casters occasionally.

(See Figure 10) These should be checked especially after use on uneven ground.

7

QMP1MB Installation Instructions

Chief Manufacturing, a products division of Milestone AV Technologies

8809-002005 Rev00

2011 Milestone AV Technologies, a Duchossois Group Company www.chiefmfg.com

01/11

USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378

P 800.582.6480 / 952.894.6280

Europe

F 877.894.6918 / 952.894.6918

A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands

P +31 (0)40 2668620

Asia Pacific

F +31 (0)40 2668615

A Office No. 1 on 12/F, Shatin Galleria

18-24 Shan Mei Street

Fotan, Shatin, Hong Kong

P 852 2145 4099

F 852 2145 4477

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Key Features

  • Multimedia stand Black
  • Material: Steel
  • Maximum weight capacity: 90.71 kg

Related manuals

Download PDF

advertisement