Chief MPAUB Installation Instructions

I N S T A L L A T I O N I N S T R U C T I O N S

Instrucciones de instalación

Installationsanleitung

Instruções de Instalação

Istruzioni di installazione

Installatie-instructies

Instructions d´installation

Height Adjustable Video Cart

Spanish Product Description

German Product Description

Portuguese Product Description

Italian Product Description

Dutch Product Description

French Product Description

MPAU

MPAU

DISCLAIMER

Milestone AV Technologies and its affiliated corporations and subsidiaries (collectively "Milestone"), intend to make this manual accurate and complete. However, Milestone makes no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.

Chief® is a registered trademark of Milestone AV Technologies.

All rights reserved.

Installation Instructions

WARNING: Use this mounting system only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.

WARNING: Never operate this mounting system if it is damaged. Return the mounting system to a service center for examination and repair.

WARNING: Do not use this product outdoors.

WARNING: RISK OF INJURY TO PERSONS! Do not place video equipment such as televisions or computer monitors on cart legs.

--SAVE THESE INSTRUCTIONS--

IMPORTANT SAFETY INSTRUCTIONS

WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION: A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresponding instructions.

WARNING: Failure to read, thoroughly understand, and follow all instructions can result in serious personal injury, damage to equipment, or voiding of factory warranty! It is the installer’s responsibility to make sure all components are properly assembled and installed using the instructions provided.

WARNING: Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment.

Reinforce the structure as required before installing the component.

WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components located between the MPAU up to (and including) the display does not exceed 125 lbs (56.7 kg).

2

Installation Instructions

DIMENSIONS

+/-2 ROLL

ADJUSTMENT

CABLE CORD WRAP HOOKS

TILT

ADJUSTMENT

47.74

1212.5

MPAU

3

MPAU

LEGEND

Tighten Fastener

Apretar elemento de fijación

Befestigungsteil festziehen

Apertar fixador

Serrare il fissaggio

Bevestiging vastdraaien

Serrez les fixations

Loosen Fastener

Aflojar elemento de fijación

Befestigungsteil lösen

Desapertar fixador

Allentare il fissaggio

Bevestiging losdraaien

Desserrez les fixations

Phillips Screwdriver

Destornillador Phillips

Kreuzschlitzschraubendreher

Chave de fendas Phillips

Cacciavite a stella

Kruiskopschroevendraaier

Tournevis à pointe cruciforme

Open-Ended Wrench

Llave de boca

Gabelschlüssel

Chave de bocas

Chiave a punte aperte

Steeksleutel

Clé à fourche

By Hand

A mano

Von Hand

Com a mão

A mano

Met de hand

À la main

Hex-Head Wrench

Llave de cabeza hexagonal

Sechskantschlüssel

Chave de cabeça sextavada

Chiave esagonale

Zeskantsleutel

Clé à tête hexagonale

4

Installation Instructions

Adjust

Ajustar

Einstellen

Ajustar

Regolare

Afstellen

Ajuster

Remove

Quitar

Entfernen

Remover

Rimuovere

Verwijderen

Retirez

Pencil Mark

Marcar con lápiz

Stiftmarkierung

Marcar com lápis

Segno a matita

Potloodmerkteken

Marquage au crayon

Drill Hole

Perforar

Bohrloch

Fazer furo

Praticare un foro

Gat boren

Percez un trou

Optional

Opcional

Optional

Opcional

Opzionale

Optie

En option

Security Wrench

Llave de seguridad

Sicherheitsschlüssel

Chave de segurança

Chiave di sicurezza

Veiligheidssleutel

Clé de sécurité

Installation Instructions

TOOLS REQUIRED FOR INSTALLATION

MPAU

#2

M5 (included)

3/16" (included)

PARTS

T (1)

[hardware bag]

A (4)

[upright cover]

C (1)

[column upper cover]

B (2)

[interface upright]

D (1)

[column inner cover]

TA (8)

M4x16mm

TB (6)

M4x20mm

TC (6)

M4x25mm

G (1)

[back cover]

TD (6)

M5x16mm

TE (6)

M5x20mm

E (1)

[interface head assembly]

J (1)

[right cart leg]

F (1)

[column assembly]

K (2)

[cable hook]

H (1)

[left cart leg]

TG (6)

M6x16mm

TI (6)

M8x20mm

TJ (6)

TH (6)

M8x30mm

TF (6)

M5x25mm

M6x25mm

TK (4)

M8x50mm

L (1)

[left transition cover]

M (1)

[right transition cover]

TL (8)

1/4"

TM (8)

1/2"

TN (8)

[universal]

TP (1)

M5

N (5)

5/16-18 x 3/4"

P (4)

5/16-18 x 3 3/4"

Q (2)

1/4-20 x 1/2"

R (1)

3/16"

U (10)

[FCA clip]

V (10)

[cable clip]

W (1)

3/16"

5

MPAU

Assembly And Installation

CAUTION: Attachment holes may be damaged if a power drill is used to insert button head cap screws. Screws should first be inserted and turned BY HAND with the hex key or with a handheld screwdriver BEFORE using the head head drill bit and power drill to complete the attachment.

Cart Assembly

1.

Carefully set column assembly (F) on its left side. (See

Figure 1)

2.

Place right transition cover (M) on right cart leg (J), lining up the holes on the cover with the holes on the leg and column assembly base. (See Figure 1)

3.

Use two 5/16-18 x 3 3/4" button head cap screws (P) to secure leg (J) and cover (M) to column assembly (F). (See

Figure 1)

(rear view)

3 (P) x 2

Installation Instructions

5.

Place left transition cover (L) on left cart leg (H), lining up the holes on the cover with the holes on the leg and column assembly base. (See Figure 2)

6.

Use two 5/16-18 x 3 3/4" button head cap screws (P) to secure leg (H) and cover (L) to column assembly (F). (See

Figure 2)

7.

Slide interface head assembly (E) into column assembly

(F). (See Figure 3)

8.

Use four 5/16-18 x 3/4" button head cap screws (N) to secure interface head assembly (E) to column assembly

(F). (See Figure 3)

8 (N) x 4

(E)

7

(F)

(J)

2

(M)

(F)

1

Figure 1

4.

Turn column assembly (F) onto its right side. (See Figure 2)

6

(P) x 4

Figure 3

9.

Use remaining 5/16-18 x 3/4" button head cap screw (N) to secure column upper cover (C) to interface head assembly

(E). (See Figure 4)

10. Snap column inner cover (D) onto column assembly (F).

(See Figure 4)

9 (N)

(C)

(H)

(E)

(D)

5

(L)

4

10

(F)

10

(F)

Figure 2

Figure 4

6

Installation Instructions

Display Installation

MPAU

WARNING: Exceeding the weight capacity can result in serious personal injury or damage to equipment! It is the installer’s responsibility to make sure the combined weight of all components located between the MPAU up to (and including) the display does not exceed 125 lbs (56.7 kg).

1.

Lay display face down on protective surface.

CAUTION: Using screws of improper diameter may damage your display! Proper screws will easily thread into display mounting holes.

2.

Select screw diameter by examining hardware (TA-TK)

(4mm, 5mm, 6mm or 8mm) and comparing with mounting holes on display. (See Figure 5)

3.

Select spacers: (See Figure 5)

• If mounting holes are not recessed and both uprights (B) can lay flat against display, then no spacers are required.

• If mounting holes are recessed, or if protrusions prevent uprights (B) from laying flat, then spacers

(TL or TM) must be used.

CAUTION: Using screws of improper length may damage your display! Proper screws will have adequate thread engagement without contacting bottom of display mounting holes.

4.

Select screw length: (See Figure 5)

• Using your hand, insert SHORTEST length screw of selected diameter (TA, TD, TG or TI) through universal washer (TN), uprights (B), selected spacer (TL or TM), into display mounting hole. Do

NOT thread screw into hole at this time.

NOTE: Universal washers (TN) are not needed if using M8 button head cap screws (TI, TJ or TK).

• Proper screw length requires base of screw head to protrude above flat washer a distance equal to

or greater than the screw diameter. If screw length is inadequate, select longer screw. Select

shortest screw which will protrude the required distance.

5.

Place uprights (B) on display, ensuring: (See Figure 5)

• Center of uprights (B) are as close to the center of the back of display as possible after being installed. Center of bracket is indicated by the diamond-shaped hole.

6.

Use selected screws and spacers to install two interface uprights (B) to back of display. (See Figure 5)

6 (TA-TH) or (TI-TK) x 4, 6 or 8

(B) x 2

5

5

3 (TL or TM)

Figure 5

7

MPAU

WARNING: Display may be very heavy! Ensure display may be safely lifted and maneuvered as required to install on cart. Failure to take adequate precautions can result in serious personal injury or damage to equipment!

7.

Position latches on interface uprights so that they are in the

"open" position. (See Figure 6)

8.

Hang interface uprights (B) on interface head assembly (E).

(See Figure 6)

Installation Instructions

9.

Move latches on interface uprights to the "closed" position to secure display to head assembly. (See Figure 8)

9 open position

9

Figure 8

10. Snap four upright covers (A) onto uprights. (See Figure 9)

NOTE: Tabs on inside of covers (A) will snap directly into holes on uprights to ensure a secure connection.

7

8

7

8

Figure 6

IMPORTANT ! : In order to ensure an even mount, install uprights to be centered over column assembly. Do NOT install both uprights to the same side of column assembly! (See Figure 7)

(B) x 2

10 (A) x 4

11

Figure 9

11. (Optional) Use padlocks (not provided) to secure uprights to head assembly. (See Figure 9)

Figure 7

8

Installation Instructions

Cable Management

NOTE: The following cable management options may vary based on type of display being mounted and user preference.

1.

Use two 1/4-20 x 1/2" Phillips pan machine screws (Q) to attach two cable hooks (K) to bottom of column assembly

(F). (See Figure 10)

MPAU

5.

Route cables along FCA clips to be used for cable management. (See Figure 12)

6.

Use cable ties (V) to secure cables to FCA clips. (See

Figure 12)

(F)

5

6 (V)

(K) x 2 1 (Q) x 2

Figure 10

2.

Place FCA clip (U) into groove on back of Fusion mount with clip handle in a vertical position. (See Figure 11)

3.

Rotate FCA clip (U) 90° in either direction until clip handle is in a horizontal position. (See Figure 11)

4.

Repeat Steps 1-2 for all clips to be installed.

Figure 12

7.

Route cables from display through front channel of column assembly. (See Figure 13) cable (example)

3

3

2

(U) clip handle front channel

Figure 13

7

Figure 11

9

MPAU

8.

Route cables down column channel, tucking them behind height-adjustment carriage and underneath bracket holding height-adjustment shaft. (See Figure 14)

9.

Wrap cables around cable hooks hooks as desired. (See

Figure 14)

10. Snap back cover (G) onto back of column assembly making sure cables fit through opening at bottom of cover. (See

Figure 14)

Installation Instructions

Adjustments

Height Adjustment

1.

Remove cable cover (G) to expose height adjustment knob.

2.

Turn height adjustment knob clockwise to raise display.

(See Figure 15)

3.

Turn height adjustment knob counterclockwise to lower display. (See Figure 15)

(rear view)

10

(G)

WARNING: Do not attempt to raise or lower the adjustment carriage beyond its upper or lower limit. High and low points are shown in Figures 15 and 16.

NOTE: A 1/2" socket wrench may also be used to adjust height by turning bolt just above height adjustment knob.

4.

Reinstall cable cover (G) to column assembly.

8

10 height adjustment knob

8 under bracket

2 3

1 high point

2

1 9 cable hooks

Figure 14 cable opening

3

Figure 15 low point

Figure 16

10

Installation Instructions

Pitch Adjustment

5.

Turn pitch adjustment knob clockwise to tilt display forward.

(See Figure 17)

6.

Turn pitch adjustment knob counterclockwise to tilt display back. (See Figure 17)

Roll Adjustment

7.

Turn roll adjustment knob clockwise to adjust roll to the left.

(See Figure 17)

8.

Turn roll adjustment knob counterclockwise to adjust roll to the right. (See Figure 17)

7

8

5

5 6

7 8

6 pitch adjustment knob roll adjustment knob

Figure 17

MPAU

11

MPAU Installation Instructions

Chief Manufacturing, a products division of Milestone AV Technologies

8800-002273 Rev04

2013 Milestone AV Technologies, a

Duchossois Group Company www.chiefmfg.com

01/13

USA/International A 6436 City West Parkway, Eden Prairie, MN 55344

P 800.582.6480 / 952.225.6000

Europe

F 877.894.6918 / 952.894.6918

A Franklinstraat 14, 6003 DK Weert, Netherlands

P +31 (0) 495 580 852

Asia Pacific

F +31 (0) 495 580 845

A Office No. 1 on 12/F, Shatin Galleria

18-24 Shan Mei Street

Fotan, Shatin, Hong Kong

P 852 2145 4099

F 852 2145 4477