Netgear Arlo Quick Start Guide
Add to my manuals
16 Pages
Netgear Arlo is a wireless home security camera system that lets you keep an eye on your property from anywhere. With 100% wire-free cameras, you can place them anywhere inside or outside your home, and they'll connect to your Wi-Fi network and the Arlo app on your smartphone, tablet, or computer. Arlo cameras are weather-resistant, so you can use them indoors or outdoors, and they have night vision capabilities, so you can see what's happening even in the dark.
advertisement
Quick Start Guide
1
2
Welcome
Thank you for choosing Arlo.
Getting started is easy.
What’s Included
Base station Base station power adapter
Ethernet cable Magnetic wall mounts
Mounting screws
100% wireless camera(s)
Lithium 123 batteries
(number of batteries varies with number of cameras)
3
1
Get the App
For the best experience, download the Arlo app for your smartphone by scanning the QR code below or searching for “Arlo” in the app store.
4
http://www.netgear.com/arloapps
2
Connect Your Base Station to the Internet
Connect the base station to your router using an Ethernet cable.
Connect the AC adapter to your base station and plug it in.
5
6
Turn the base station on by pressing the
On-Off button.
The power LED and Internet LED on the front of the base station turn green in about two minutes.
(If this doesn’t happen, visit http://support.arlo.com
for troubleshooting tips.)
3
Get an Account
Launch the app from your smartphone and click the New System Setup button.
Follow the on-screen instructions.
Or from a computer, visit https://arlo.netgear.com/ and follow the on-screen instructions.
7
Available AFTER beta
8
4
Set Up and Sync Your Cameras
Insert batteries
• Unlock the battery compartment by
sliding and holding the latch.
• Slide the battery door back and lift
it to open the compartment.
• Insert the batteries as shown and close
the battery door.
Sync your cameras with the base station
Bring the camera within one to three feet (30 to 100 centimeters) of the base station.
1’ - 3’
30 cm - 100 cm
9
Sync your cameras with the base station (cont’d)
Press the Sync button on the side of the base station.
Wait for the sync status LED to blink green.
Press the Sync button on top of the camera.
Cameras must be synced one at a time.
10
A blue LED on the camera blinks rapidly to confirm sync.
The camera is ready for viewing.
Note: The LED blinks amber if the sync is not successful. You must repeat the sync process.
The camera LED on the base station turns solid green after the camera is synced.
Note: If the sync procedure is not completed within 60 seconds, press the Sync button on the base station and try again .
Repeat these steps for each camera.
11
5
Place or Mount Your Cameras
Locate a spot for your camera
You can place your camera on a shelf or other flat surface, or you can mount it to the wall.
Tip: Use the Arlo app in Position mode
(found in Camera Settings) to help aim the camera.
12
To mount your camera to the wall:
Fasten the mounting screw into the wall, and hang the magnetic mount from the screw.
If you’re mounting the camera to drywall, be sure to use the drywall plastic anchors that are provided.
Tip: You can also use double-sided tape instead of screws.
13
14
You’re Done!
Congratulations! Your Arlo System is set up and ready to go.
To view useful tutorial videos, find troubleshooting tips, or get support, visit http://support.arlo.com
or call (US only)
1-888-NETGEAR .
Base Station LED Guide
Power
Green
The base station is powered on.
Blinking green
A firmware update is in progress. DO
NOT TURN OFF
BASE STATION OR
CAMERAS.
Amber
The base station is booting up.
Off
The base station is powered off.
Reserved for upcoming features
Internet
Green
The base station is connected to the Internet.
Blinking green
The base station is sending data over the Internet.
Amber
The base station is connected to the router but does not have an Internet connection.
Off
The base station is not connected to your router.
Camera
Green
Cameras are connected to the base station.
Blinking green
The base station is attempting to sync with a camera.
Blinking amber
A camera is too far from the base station. Signal strength is weak.
Off
No cameras detected..
15
©2014 NETGEAR, Inc. NETGEAR, the NETGEAR Logo, and Arlo are trademarks of NETGEAR, Inc.
Compliance
For regulatory compliance information, visit
http://www.netgear.com/about/regulatory/ .
350 East Plumeria Drive
San Jose, CA 95134, USA
October 2014
16
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- Indoor & outdoor IP security camera
- CMOS 1280 x 720 pixels
- Wired & Wireless Ethernet LAN Wi-Fi
- Night vision 7.62 m IR
- Cube Ceiling/wall
- IP65
- White
Related manuals
advertisement