MOTION DETECTOR INSIDE MDI01

MDI01 : Motion Detector Inside

Technical Product Information

MOTION DETECTOR INSIDE MDI01

Figure 1 : Bticino

®

Motion Detector MDI01/N Light

1. Product Description

This module contains a motion detector with adjustable angle and an integrated light cell. The detector is integrated in a built-in frame with claw attachment. A bus connection with connector (no polarity) has been provided. The motion detector has a range of approximately 7m at an angle of 110 degrees. The light cell is positioned internally.

The motion detector MDI01 can make the difference between movement coming from the left or the right when it’s wall mounted and when the movement crosses the angle. This can be useful for distinguishing an incoming or an outgoing movement.

The Serial Manager software allows you determine whether the output is a combination of motion AND light or only motion or only light.

Software-settings:

Triggers:

First: This is the amount of movement needed to activate the output (higher = more movement needed to activate)

Keep : Is the amount of movement to maintain the output activated. (higher = more movement needed to keep activated)

Sensitivity: How sensitive the MDI is to air-flow.

Sensitivity can be set on a high leven (higher = more sensitive), but if e.g. outputs are activated when no-one is in the room sensitivity should be reduced (MDI is reacting to airflows of heating e.g.).

With the Timers the time can be set during which the outputs will be activated (extension). The Lock timer is used to lock the detector from directional detection when this is being used. E.g. the MDI can be set to detect motion from left to right or vice versa.

The Led (inside the MDI) can be set to blink based on movement or based on Light every 2 or 5 seconds.

One can program up to 4 outputs (only Toggle). Every output must be activated by one (eg. Left) or more actions (eg. Left+Right and light cel). When Alarm is selected this means that this specific output will be activated when the Alarm-trigger is activated.

Actions for activating the output:

Alarm: When there is a certain level of continuous

movement (5 seconds).

Light: The amount of light is less than the value set.

The Overrule LDR function allows you to select an output which, when activated, disables the light sensor on this MDI so it will only function based on movement.

To use the MDI based on movement, both movement flags (L and R) need to be activated.

All outputs still can be controlled by other inputs (eg. switches,...). Options exist to give priority, temporary disable output, ...

THE MODULE SHOULD BE MOUNTED ON THE

BEST PLACE TO GET A MAXIMUM COVERAGE

OF THE ‘VIEWING ANGLE’ AND NOT IN ANY

DIRECT LOCATION NEAR HEATING OR

COOLING DEVICES.

NEVER CONNECT OR DISCONNECT MODULES

WHILE THE BUS IS ENERGIZED!

2. Safety Instructions

Read the complete manual before carrying out the installation and activating the system.

WARNING

________________________________________________________



The device must be mounted and commissioned by an authorised electrician in accordance with the country-specific regulations.



The device may be used for permanent INTERIOR installations in dry locations within box mounts.

________________________________________________________________________________________________________

© QBUS NV.

Joseph Cardijnstraat 19

B-9420 Erpe-Mere

Belgium

Page 1/3 Technical Product Information

October2010

TB/MDI01/EN_02

MDI01 : Motion Detector Inside

Technical Product Information

MOTION DETECTOR INSIDE MDI01



The device must not be installed in box mounts together with 230V devices.



The device must not be opened.

________________________________________________________

3. Mounting and wiring

Bticino

®

MDI01/L Living

Niko

®

:

Figure 2 : Connection MDI01

FITTING BTICINO

®

, NIKO

®



:

Mount the MDI01 into a mounting box and secure with the claw attachment. Connect the bus cable to the back of the switch.

IMPORTANT :

THE BUS MUST NEVER COME INTO CONTACT

WITH THE EARTHING OR A LIVE WIRE!

ADJUST VIEWING ANGLE



:

Adjust the motion detector to get the maximum coverage of the room.

LED INDICATION



:

Red LED : motion + light indicator.

4. Different versions

Niko

®

MDI01/100 (Cream) Niko

®

MDI01/121 (Sterling)

Bticino

®

:

Niko

®

MDI01/122 (Anthracite)

5. Technical Data

Bticino

®

MDI01/N Light Bticino

®

MDI01/NT Light-Tech

GENERAL SPECIFICATIONS :



Power supply : bus connection



Ambient temperature :

Working temp. range : 10°C to 50°C

Storage temp. range : -10°C to 60°C



Maximum humidity : 93%, no moisture condensation



Bus load : 15mA at nominal 13,8V



Maximum installation altitude : 2.000m

________________________________________________________________________________________________________

© QBUS NV.

Joseph Cardijnstraat 19

B-9420 Erpe-Mere

Belgium

Page 2/3 Technical Product Information

October2010

TB/MDI01/EN_02

MDI01 : Motion Detector Inside

Technical Product Information

MOTION DETECTOR INSIDE MDI01

PHYSICAL SPECIFICATIONS



Housing : Plastic



Protection Degree : IP20, EN 60529



Dimensions :

Bticino

®

: 73mmx72mm

Niko

®

: 71mmx73mm



Weight : Bticino

®

,Niko

®

= 0,053kg

ELECTRICAL SAFETY



Bus : 13,8VDC safety extra low voltage (according

EN 60950 – 1 : 2006).

CE



Complies with the EMC regulations. The device complies with EN 61000-4-2 and 50090-2-2.

6. Dimension Diagram

Dimensions in mm.

Bticino

®

:

Any faulty devices should be send postage-free with a description of the defect to our central customer service office :

QBUS N.V.

Joseph Cardijnstraat 19

9420 Erpe-Mere

Belgium

T +32 53 60 72 10

F +32 53 60 72 19

Email : [email protected]

Niko

®

:

7. Guarantee provisions

Period of guarantee : 2 years from date of delivery.

Guarantee will not be accepted if the device has been opened!

________________________________________________________________________________________________________

© QBUS NV.

Joseph Cardijnstraat 19

B-9420 Erpe-Mere

Belgium

Page 3/3 Technical Product Information

October2010

TB/MDI01/EN_02