- Computers & electronics
- Telecom & navigation
- Telephones
- Avaya
- 1600 Series IP Deskphones
- Operating instructions
advertisement
Avaya 1600 Series IP Deskphones
Administrator Guide
Release 1.3.5
16-601438
Issue 5
May 2014
© 2014 Avaya Inc.
All Rights Reserved.
Notice
While reasonable efforts were made to ensure that the information in this document was complete and accurate at the time of printing, Avaya Inc. can assume no liability for any errors. Changes and corrections to the information in this document may be incorporated in future releases.
For full legal page information, please see the complete document, Avaya
Legal Page for Hardware Documentation, Document number 03-600759.
To locate this document on our Web site, simply go to http:// www.avaya.com/support and search for the document number in the search box.
Documentation disclaimer
Avaya Inc. is not responsible for any modifications, additions, or deletions to the original published version of this documentation unless such modifications, additions, or deletions were performed by Avaya. Customer and/or End User agree to indemnify and hold harmless Avaya, Avaya's agents, servants and employees against all claims, lawsuits, demands and judgments arising out of, or in connection with, subsequent modifications, additions or deletions to this documentation to the extent made by the Customer or End User.
Link disclaimer
Avaya Inc. is not responsible for the contents or reliability of any linked Web sites referenced elsewhere within this documentation, and Avaya does not necessarily endorse the products, services, or information described or offered within them. We cannot guarantee that these links will work all of the time and we have no control over the availability of the linked pages.
Warranty
Avaya Inc. provides a limited warranty on this product. Refer to your sales agreement to establish the terms of the limited warranty. In addition, Avaya’s standard warranty language, as well as information regarding support for this product, while under warranty, is available through the following Web site: http://www.avaya.com/support
Copyright
Except where expressly stated otherwise, the Product is protected by copyright and other laws respecting proprietary rights. Unauthorized reproduction, transfer, and or use can be a criminal, as well as a civil, offense under the applicable law.
Avaya support
Avaya provides a deskphone number for you to use to report problems or to ask questions about your product. The support deskphone number is 1-800-242-2121 in the United States. For additional support deskphone numbers, see the Avaya Web site: http://www.avaya.com/support
Software License
USE OR INSTALLATION OF THE PRODUCT INDICATES THE END USER’S
ACCEPTANCE OF THE TERMS SET FORTH HEREIN AND THE GENERAL
LICENSE TERMS AVAILABLE ON THE AVAYA WEBSITE AT http:// support.avaya.com/LicenseInfo/ (“GENERAL LICENSE TERMS”). IF YOU DO
NOT WISH TO BE BOUND BY THESE TERMS, YOU MUST RETURN THE
PRODUCT(S) TO THE POINT OF PURCHASE WITHIN TEN (10) DAYS OF
DELIVERY FOR A REFUND OR CREDIT.
Avaya grants End User a license within the scope of the license types described below. The applicable number of licenses and units of capacity for which the license is granted will be one (1), unless a different number of licenses or units of capacity is specified in the Documentation or other materials available to End User. “Designated Processor” means a single stand-alone computing device. “Server” means a Designated Processor that hosts a software application to be accessed by multiple users. “Software” means the computer programs in object code, originally licensed by Avaya and ultimately utilized by End User, whether as stand-alone Products or pre-installed on Hardware. “Hardware” means the standard hardware
Products, originally sold by Avaya and ultimately utilized by End User.
License Type(s):
Designated System(s) License (DS). End User may install and use each copy of the Software on only one Designated Processor, unless a different number of Designated Processors is indicated in the Documentation or other materials available to End User. Avaya may require the Designated Processor(s) to be identified by type, serial number, feature key, location or other specific designation, or to be provided by End User to Avaya through electronic means established by Avaya specifically for this purpose.
Third-party Components
Certain software programs or portions thereof included in the Product may contain software distributed under third party agreements (“Third Party
Components”), which may contain terms that expand or limit rights to use certain portions of the Product (“Third Party Terms”). Information identifying
Third Party Components and the Third Party Terms that apply to them is available on Avaya’s Web site at: http://support.avaya.com/ThirdPartyLicense/
Interference
Using a cell, mobile, or GSM deskphone, or a two-way radio in close proximity to an Avaya IP Deskphone might cause interference.
Security
See http://support.avaya.com/security to locate and/or report known vulnerabilities in Avaya products. See http://support.avaya.com
to locate the latest software patches and upgrades. For information about secure configuration of equipment and mitigation of toll fraud threats, see the Avaya
Toll Fraud and Security Handbook at http://support.avaya.com
.
Contents
Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
New in this release. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Document Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Other Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 2: Administration Overview and Requirements . . . . . . . . . . . . . . . . . . .
1600 Series IP Deskphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parameter Data Precedence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The Administrative Process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Administrative Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Deskphone Initialization Process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 1: Deskphone to Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 2: DHCP Server to Deskphone . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 3: Deskphone and File Server . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 4: Deskphone and the Call Server . . . . . . . . . . . . . . . . . . . . . . . .
Error Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 3: Network Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Network Assessment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Hardware Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Server Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DHCP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HTTP/HTTPS Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Required Network Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Other Network Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reliability and Performance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IEEE 802.1P and 802.1Q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network Audio Quality Display on 1600 Series IP Deskphones . . . . . . . . . . .
IP Address Lists and Station Number Portability . . . . . . . . . . . . . . . . . . .
TCP/UDP Port Utilization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Registration and Authentication . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 4: Avaya Aura Communication Manager Administration . . . . . . . . . . . . . .
Call Server Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switch Compatibility and Aliasing IP Deskphones . . . . . . . . . . . . . . . . . .
Issue 5 May 2014 1
Media Server (Switch) Administration . . . . . . . . . . . . . . . . . . . . . . . . . . .
IP Interface and Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UDP Port Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RSVP and RTCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
QoS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IEEE 802.1P and 802.1Q . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIFFSERV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voice Mail Integration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
1600 Series IP Deskphones with Avaya Aura Communication Manager 5.2 Native Support
1600 Series IP Deskphones Aliased as 4600 Series IP Deskphones . . . . . . . . . 30
Deskphone Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System-Wide Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Feature-Related System Parameters . . . . . . . . . . . . . . . . . . . . . . . . . .
Administering Stations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Aliasing 1600 Series IP Deskphones . . . . . . . . . . . . . . . . . . . . . . . . . .
Administering Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Feature Buttons and Call Appearances . . . . . . . . . . . . . . . . . . . . . . . . . .
For the 1603/1603SW/1603-I/1603SW-I and 1608/1608-I IP Deskphones . . . . . . .
For the 1616/1616-I IP Deskphones . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conference Details Screen for Ad-Hoc Conferences . . . . . . . . . . . . . . . . .
Shuffling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Printing Button Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 5: Server Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Software Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DHCP and File Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
DHCP Server Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DHCP Generic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windows NT 4.0 DHCP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Verifying the Installation of the DHCP Server . . . . . . . . . . . . . . . . . . .
Creating a DHCP Scope for the IP Deskphones . . . . . . . . . . . . . . . . . .
Editing Custom Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adding the DHCP Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Activating the Leases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Verifying Your Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windows 2000 DHCP Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Verifying the Installation of the DHCP Server . . . . . . . . . . . . . . . . . . .
Adding DHCP Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Activating the New Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HTTP Generic Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HTTP Configuration for Backup/Restore. . . . . . . . . . . . . . . . . . . . . . . . . .
For IIS Web Servers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Web Configuration Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 6: Deskphone Software and Application Files . . . . . . . . . . . . . . . . . . . .
General Download Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1600 Series IP Deskphone Scripts and Application Files . . . . . . . . . . . . . . . . .
Choosing the Right Application File and Upgrade Script File . . . . . . . . . . . .
Upgrade Script File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Settings File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents of the Settings File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The GROUP System Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Call Center Administration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 7: Administering Deskphone Options . . . . . . . . . . . . . . . . . . . . . . . .
Administering Options for the 1600 Series IP Deskphones . . . . . . . . . . . . . . .
VLAN Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
VLAN Tagging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
VLAN Default Value and Priority Tagging . . . . . . . . . . . . . . . . . . . . . . .
VLAN Separation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DNS Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IEEE 802.1X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
802.1X Pass-Through and Proxy Logoff . . . . . . . . . . . . . . . . . . . . . . . .
802.1X Supplicant Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Link Layer Discovery Protocol (LLDP) . . . . . . . . . . . . . . . . . . . . . . . . . . .
Local Administrative Options Using the Deskphone Dialpad . . . . . . . . . . . . . .
Clear Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disabling or enabling the Debug mode . . . . . . . . . . . . . . . . . . . . . . . .
Group Identifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset System Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restart the Deskphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interface Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The View Local Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Static Addressing Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disable/Enable Event Logging . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logoff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Issue 5 May 2014 3
Self-Test Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
1600 Series Global Deskphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
1600 Series International Deskphones . . . . . . . . . . . . . . . . . . . . . . . . . 103
Enhanced Local Dialing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Backup/Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
Restore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Chapter 8: Administering Applications and Options . . . . . . . . . . . . . . . . . . . . . 111
Customizing 1600 Series IP Deskphone Applications and Options . . . . . . . . . . . 111
The Application Status Flag (APPSTAT) . . . . . . . . . . . . . . . . . . . . . . . . 114
Appendix A: Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Appendix B: Related Documentation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
IETF Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
ITU Documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
ISO/IEC, ANSI/IEEE Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Appendix C: Sample Administration Forms . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
4 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Chapter 1: Introduction
About This Guide
This guide is for personnel who administer Avaya Aura™ Communication Manager, Avaya Aura
Communication Manager Branch (formerly known as Avaya Distributed Office), DHCP, HTTP/HTTPS servers for Avaya 1600 Series IP Deskphones, a Local Area Network (LAN), or a Web server.
The 1600 Series IP Deskphones use Internet Protocol (IP) technology with Ethernet line interfaces and support the H.323 protocol only. The 1600 Series IP Deskphones provide support for DHCP, HTTP, and
HTTPS over IPv4, which enhances the administration and servicing of the deskphones. These deskphones use DHCP to obtain dynamic IP Addresses, and HTTPS or HTTP to download new versions of software or customized settings for the deskphones.
CAUTION:
!
CAUTION:
Avaya does not support many of the products mentioned in this document. Take care to ensure that there is adequate technical support available for servers used with any 1600
Series IP Deskphone system. If the servers are not functioning correctly, the 1600 Series
IP Deskphones might not operate correctly.
New in this release
Release 1.3.5 has the following new enhancements:
● Supported on the 1603, 1603-I, 1603SW, 1603SW-I, 1608, 1608-I, 1616, and 1616-I IP
Deskphones only. This package will not load or operate on any other models.
● Avaya recommends that all the customers upgrade both new and installed 1600 Series IP
Deskphones to this version at their earliest convenience.
Issue 5 May 2014 1
Introduction
Document Organization
The guide contains the following sections:
Software and Application Files
Provides an overview of this document.
Provides an overview of the administrative process and describes general hardware, software, and operational requirements.
Describes administrative requirements for your Local Area
Network.
Describes how to administer Avaya Aura Communication
Manager to operate with 1600 Series IP Deskphones.
Describes DHCP, HTTP, and HTTPS administration for the
1600 Series IP Deskphones.
Describes deskphone software, covers application software downloads, and provides information about the configuration file.
Describes how to use file parameters and options to administer 1600 Series IP Deskphones. Covers backup and restoration of deskphone data. Also describes how to use local procedures to customize a single deskphone from the dialpad.
Provides a table of customizable application-specific parameters, to provide administrative control of deskphone functions and options.
Provides a glossary of terms used in this document or which can be applicable to 1600 Series IP Deskphones.
Provides references to external documents that relate to telephony in general, which can provide additional information about specific aspects of the deskphones.
Provides examples of Avaya Aura Communication Manager forms related to system-wide and individual deskphone administration.
2 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Other Documentation
Other Documentation
See the Avaya support site at http://www.avaya.com/support for 1600 Series IP Deskphone technical and end user documentation.
The following documents are available for the 1600 Series IP Deskphones:
● Avaya 1600 Series IP Deskphones Installation and Maintenance Guide, Document Number
16-601438.
● Avaya one-X™ Deskphone Value Edition 1600 Series IP Deskphone Pre-Installation Checklist,
Document Number 16-601439.
● Avaya one-X™ Deskphone Value Edition 1600 Series IP Deskphone Safety Instructions,
Document Number 16-601440.
● Avaya one-X™ Deskphone Value Edition 1600 Series IP Deskphones BM32 Button Module
Installation and Safety Instructions, Document Number 16-601441.
● Avaya one-X™ 9600 Series IP Deskphone Application Programmer Interface (API) Guide,
Document Number 16-601442.
● Avaya 1600 Series IP Deskphones Administrator Guide, Document Number 16-601443.
● Avaya 1603/1603SW/1603-I/1603SW-I IP Deskphone User Guide, Document Number
16-601444.
● Avaya 1608/1608-I IP Deskphone User Guide, Document Number 16-601446.
● Avaya 1616/1616-I IP Deskphone User Guide, Document Number 16-601448.
● Avaya one-X™ Deskphone Value Edition 1600 Series IP Deskphones BM32 Button Module User
Guide, Document Number 16-601450
● Avaya one-X™ Deskphone Value Edition 1600 Series IP Deskphone Wall Mount Instructions,
Document Number 16-601453.
● Avaya one-X™ Deskphone Value Edition 1600 Series IP Deskphone Stand Instructions,
Document Number 16-601451.
● Avaya 1603/1603SW/1603-I/1603SW-I IP Deskphone Quick Reference,
Document Number 16-601445.
● Avaya 1608/1608-I IP Deskphone Quick Reference, Document Number 16-601447.
● Avaya 616/1616-I IP Deskphone Quick Reference, Document Number 16-601449.
See
Appendix B: Related Documentation
for a list of non-Avaya documents, such as those published by the Internet Engineering Task Force (IETF) and the International Telecommunication Union (ITU).
Issue 5 May 2014 3
Introduction
4 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Chapter 2: Administration Overview and
Requirements
1600 Series IP Deskphones
The 1600 Series IP Deskphones currently support the H.323 signaling protocol.
The H.323 standard provides for real time audio, video, and data communications transmission over a packet network. An H.323 deskphone protocol stack comprises several protocols:
● H.225 for registration, admission, status (RAS), and call signaling,
● H.245 for control signaling,
● Real Time Transfer Protocol (RTP), and
● Real Time Control Protocol (RTCP)
The parameters under which the 1600 Series IP Deskphones need to operate are summarized as follows:
● Deskphone and System Administration on the Avaya Media Server, as covered in
Chapter 4: Avaya Aura Communication Manager Administration .
● IP address management for the deskphone, as covered in
DHCP and File Servers on page 37 for
dynamic addressing. For static addressing, see the Avaya 1600 Series IP Deskphones Installation
and Maintenance Guide.
● Tagging Control and VLAN administration for the deskphone, if appropriate, as covered in
7: Administering Deskphone Options
.
● Quality of Service (QoS) administration for the deskphone, if appropriate. QoS is covered in
on page 19 and QoS on page 28.
● Interface administration for the deskphone, as appropriate. Administer the deskphone to LAN interface using the PHY1 parameter described in
Chapter 3: Network Requirements
. Administer the deskphone to PC interface using the PHY2 parameter described in “Local Procedures” in the
Avaya 1600 Series IP Deskphones Installation and Maintenance Guide.
● Application-specific deskphone administration, if appropriate, as described in
8: Administering Applications and Options . An example of application-specific data is specifying
the extent to which users can add/edit/delete data for Contacts entries.
● Protocol administration, for example, Simple Network Management Protocol (SNMP) and Link
Layer Discovery Protocol (LLDP).
Issue 5 May 2014 5
Administration Overview and Requirements
Table 1 indicates that you can administer system parameters in a variety of ways and use a variety of delivery mechanisms like:
● Maintaining the information on the call server.
● Manually entering the information by means of the deskphone dialpad.
● Administering the DHCP server.
● Editing the configuration file on the applicable HTTP or HTTPS file server.
● User modification of certain parameters, when given administrative permission to do so.
Note:
Note:
Not all parameters can be administered on all delivery mechanisms.
Table 1: Administration Alternatives and Options for 1600 Series IP
Deskphones
Parameter(s)
Administrative
Mechanisms
Deskphone
Administration
Avaya call server
IP Addresses DHCP
(strongly recommended)
Configuration file
For More Information See:
Chapter 4: Avaya Aura Communication Manager
, Chapter 5: Server Administration
, and
Appendix B: Related Documentation
.
DHCP and File Servers on page 37, and especially
DHCP Server Administration on page 38.
Manual administration at the deskphone
Chapter 6: Deskphone Software and Application
and Chapter 7: Administering Deskphone
“Static Addressing Installation” in the Avaya 1600
Series IP Deskphones Installation and
Maintenance Guide.
Tagging and
VLAN
LLDP
LLDP
DHCP
Configuration file
(strongly recommended)
Link Layer Discovery Protocol (LLDP) on page 78.
Link Layer Discovery Protocol (LLDP) on page 78.
DHCP Server Administration on page 38, and
Chapter 7: Administering Deskphone Options
.
DHCP and File Servers on page 37 and
7: Administering Deskphone Options
.
1 of 3
6 1600 Series IP Deskphone Administrator Guide Release 1.3.5
1600 Series IP Deskphones
Table 1: Administration Alternatives and Options for 1600 Series IP
Deskphones (continued)
Parameter(s)
Administrative
Mechanisms
Manual administration at the deskphone
Avaya call server
For More Information See:
“Static Addressing Installation” in the Avaya 1600
Series IP Deskphones Installation and
Maintenance Guide.
Use the change ip-network-map command to configure the VLAN ID.
2 of 3
Issue 5 May 2014 7
Administration Overview and Requirements
Table 1: Administration Alternatives and Options for 1600 Series IP
Deskphones (continued)
Parameter(s)
Quality of
Service
Interface
Administrative
Mechanisms
Avaya call server
(strongly recommended)
DHCP
Configuration file
DHCP
Configuration file
(strongly recommended)
Manual administration at the deskphone
For More Information See:
UDP Port Selection on page 28 and
Appendix B: Related Documentation
.
DHCP and File Servers on page 37, and
7: Administering Deskphone Options
.
DHCP and File Servers on page 37, and
7: Administering Deskphone Options
.
DHCP and File Servers on page 37, and
6: Deskphone Software and Application Files .
DHCP and File Servers on page 37, and
6: Deskphone Software and Application Files .
Application - specific parameters
LLDP
DHCP
Configuration file
(strongly recommended)
“Ethernet (Hub) Interface Enable/Disable” in the
Avaya 1600 Series IP Deskphones Installation and
Maintenance Guide.
Link Layer Discovery Protocol (LLDP) on page 78.
DHCP and File Servers on page 37, and especially
DHCP Server Administration on page 38.
Also, Chapter 8: Administering Applications and
DHCP and File Servers on page 37, and especially
HTTP Generic Setup on page 49. Also,
Chapter 8: Administering Applications and Options
.
3 of 3
General information about administering DHCP servers is covered in
page 37, and more specifically, DHCP Server Administration on page 38. General information about
administering HTTP servers is covered in
DHCP and File Servers , and more specifically,
. Once you are familiar with that material, you can administer deskphone options as described in
Chapter 7: Administering Deskphone Options .
8 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Parameter Data Precedence
Parameter Data Precedence
If a given parameter is administered in multiple places, the last server to provide the parameter has precedence. The precedence, from lowest to highest, is:
1. LLDP,
2. Manual administration, with the two exceptions described for the system parameter
3. DHCP,
4. HTTP/HTTPS script file,
5. the Avaya Media Server, and finally,
6. Backup files, if administered and if permitted.
Settings the IP deskphone receives from backup files or the media server overwrite any previous settings, including manual settings. The only exception to this sequence is in the case of VLAN IDs. In the case of VLAN IDs, LLDP settings of VLAN IDs are the absolute authority. Then the usual sequence applies through HTTP/HTTPS.
Note:
Note:
For the L2QVLAN and L2Q system values, LLDP settings of VLAN IDs are the absolute authority only if the LLDP task receives the VLAN IDs before DHCP and HTTP, and the
DHCP client of the deskphone is activated at all. If the LLDP task receives the VLAN IDs after DHCP negotiation, several criteria must be successful before the deskphone
accepts VLAN IDs from LLDP. For more information, see Link Layer Discovery Protocol
The Administrative Process
The following list depicts administration for a typical 1600 Series IP Deskphone network. Your own configuration might differ depending on the servers and system you have in place.
1. LAN and applicable servers administered to accept the deskphones.
2. Deskphone software downloaded from the Avaya support site.
3. 46xxsettings file updated with site-specific information, as applicable.
4. 1600 Series Deskphones installed. For more information, see the Avaya 1600 Series IP
Deskphones Installation and Maintenance Guide.
5. Individual 1600 Series IP Deskphones updated using local procedures, as applicable. For more information, see “Local Administrative Procedures” in the Avaya 1600 Series IP Deskphones
Installation and Maintenance Guide.
Issue 5 May 2014 9
Administration Overview and Requirements
Administrative Checklist
Use the following checklist as a guide to system and LAN administrator responsibilities. This high-level list helps ensure that all deskphone system prerequisites and requirements are met prior to deskphone installation.
Note:
Note:
One person might function as both the system administrator and the LAN administrator in some environments.
Table 2: Administrative Checklist
Task
Network Requirements
Assessment
Administer the call server
Description
Determine that network hardware is in place and can handle deskphone system requirements.
Verify that the call server is licensed and is administered for
Voice over IP (VoIP).
Verify the individual deskphones are administered as desired.
For More Information See:
.
.
.
Vendor-provided instructions.
DHCP server installation
Administer DHCP application
HTTP/HTTPS server installation
Install a DHCP application on at least one new or existing PC on the LAN.
Add IP deskphone administration to DHCP application.
Install an HTTP/HTTPS application on at least one new or existing PC on the LAN.
Download the files from the
Avaya support site.
Application file(s), script file, and settings file installation on HTTP/
HTTPS server
Modify settings file as desired
Edit the settings file as desired, using your own tools or the
[Avaya] Web configuration tool.
.
Vendor-provided instructions.
http://www.avaya.com/support
Chapter 6: Deskphone Software and Application Files .
Chapter 6: Deskphone Software and Application Files and
Configuration Tool on page 52.
1 of 2
10 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Deskphone Initialization Process
Note:
Table 2: Administrative Checklist (continued)
Task
Administer deskphones locally as applicable
Installation of deskphones in the network
Allow user to modify
Options, if applicable
Description
As a Group:
Individually:
For More Information See:
The GROUP System Value on page 59 and the Avaya 1600
Series IP Deskphones
Installation and Maintenance
Guide.
The applicable Local
Procedures in the Avaya 1600
Series IP Deskphones
Installation and Maintenance
Guide.
Avaya 1600 Series IP
Deskphones Installation and
Maintenance Guide.
respective User Guide for the specific deskphone model.
2 of 2
Note:
The 1608/1608-I and 1616/1616-I deskphones support the Top Line Text and Audio
Push types (but not the WML Push type).
Deskphone Initialization Process
These steps offer a high-level description of the information exchanged when the deskphone initializes and registers. This description assumes that all equipment is properly administered ahead of time. This description can help you understand how the 1600 Series IP Deskphones relate to the routers and servers in your network.
Step 1: Deskphone to Network
The deskphone is appropriately installed and powered. After a short initialization process, the deskphone identifies the LAN speed and sends a message out into the network, identifying itself and requesting further information. A router on the network receives and relays this message to the appropriate DHCP server if the phone IP address is 0.0.0.0.
Issue 5 May 2014 11
Administration Overview and Requirements
Step 2: DHCP Server to Deskphone
The DHCP file server provides information to the deskphone, as described in DHCP and File
Servers on page 37. Among other data passed to the deskphone is the IP address of the HTTP or
HTTPS server.
Step 3: Deskphone and File Server
The 1600 Series IP Deskphones can download script files and settings files from either an HTTP or
HTTPS server. These deskphones can also download the application files from the HTTP server. The deskphone queries the file server, which transmits a script file to the deskphone. This script file, at a minimum, tells the deskphone which application file the deskphone must use. The application file is the software that has the telephony functionality.
The deskphone uses the script file to determine if it has the proper application file. If the deskphone determines the proper application file is missing, the deskphone requests an application file download from the HTTP server. The deskphone then downloads the file and conducts some checks to ensure that the file was downloaded properly. If the deskphone determines it already has the proper file, the deskphone proceeds as described in the next paragraph without downloading the application file again.
The deskphone checks and loads the application file, then uses the script file to look for a settings file, if appropriate. The optional settings file can contain settings you have administered for any or all of the
1600 Series IP Deskphones in your network. For more information about this download process and settings file, see
Chapter 6: Deskphone Software and Application Files .
Step 4: Deskphone and the Call Server
The call server referred to in this step is the Avaya Media Server.
In this step, the deskphone might prompt the user for an extension and password. The deskphone uses that information to exchange a series of messages with the call server. For a new installation and for full service, the user can enter the deskphone extension and password. For a restart of an existing installation, this information is already stored on the deskphone, but the user might have to confirm the information. The deskphone and the call server exchange more messaging. The expected result is that the deskphone is appropriately registered and call server data such as feature button assignments are downloaded.
12 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Error Conditions
The 1600 Series IP Deskphones support a feature called Unnamed Registration. Unnamed
Registration allows a deskphone to register with the Avaya Media Server without an extension, assuming the Avaya Media Server also supports this feature. To invoke Unnamed Registration, take no action. Allow the Extension... prompt to display for 60 seconds without making an entry. The deskphone automatically attempts to register by means of Unnamed Registration. A deskphone registered with Unnamed Registration has the following characteristics:
● only one call appearance,
● no administrable features,
● can make only outgoing calls, subject to call server Class of Restriction/Class of Service limitations, and
● can be converted to normal “named” registration by the user entering a valid extension and password (that is, logging in).
Note:
Note:
Unnamed Registration requires administration on the Avaya Aura Communication
Manager system.
You can also administer the deskphone to avoid unnamed registration and remain unregistered if no extension and password are provided. For more information, see
.
For more information about the installation process, see the Avaya 1600 Series IP Deskphones
Installation and Maintenance Guide.
Error Conditions
Assuming proper administration, most of the problems reported by deskphone users are likely to be
LAN-based. Quality of Service, server administration, and other issues can impact user perception of
IP deskphone performance.
The Avaya 1600 Series IP Deskphones Installation and Maintenance Guide covers possible operational problems that might be encountered after successful 1600 Series IP Deskphone installation. The following User Guides also contain guidance for users having problems with specific IP deskphone applications:
● Avaya 1603/1603SW/1603-I/1603SW-I IP Deskphone User Guide,
Document Number 16-601444.
● Avaya 1608/1608-I IP Deskphone User Guide, Document Number 16-601446.
● Avaya 1616/1616-I IP Deskphone User Guide, Document Number 16-601448.
● Avaya one-X™ Deskphone Value Edition 1600 Series IP Deskphones BM32 Button Module User
Guide, Document Number 16-601450.
Issue 5 May 2014 13
Administration Overview and Requirements
14 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Chapter 3: Network Requirements
Network Assessment
Perform a network assessment to ensure that the network will have the capacity for the expected data and voice traffic, and that it can support for all applications:
● H.323,
● DHCP,
● HTTP/HTTPS, and
● Jitter buffers
Also, QoS support is required to run VoIP on your configuration. For more information, see Appendix
and
UDP Port Selection on page 28.
Hardware Requirements
To operate properly, you need:
● Category 5e cables designed to the IEEE 802.3af-2003 standard, for power over Ethernet,
●
●
For Avaya Aura Communication Manager: TN2602 IP Media Processor circuit pack. Sites with a
TN2302 IP Media Processor circuit pack are strongly encouraged to install a TN2602 circuit pack.
For Avaya Aura Communication Manager: TN799C or D Control-LAN (CLAN) circuit pack.
Important:
!
Important:
IP deskphone firmware Release 1.0 or greater requires TN799C V3 or greater CLAN circuit pack(s). For more information, see the Avaya Aura Communication Manager
Software and Firmware Compatibility Matrix on the Avaya support Web site http://www.avaya.com/support .
To ensure that the appropriate circuit pack(s) are administered on your media server, see
4: Avaya Aura Communication Manager Administration . For more information about hardware
requirements in general, see the Avaya 1600 Series IP Deskphones Installation and Maintenance
Guide.
Issue 5 May 2014 15
Network Requirements
Server Requirements
Two server types can be configured for the 1600 Series IP Deskphones:
● DHCP
● HTTP or HTTPS
Note:
Note:
HTTPS does not provide all of the functionality of HTTP. For example, backup/restore is unavailable via HTTPS, and firmware cannot be downloaded via HTTPS.
While the servers listed provide different functions that relate to the 1600 Series IP Deskphones, they are not necessarily different boxes. For example, DHCP provides file management whereas HTTP provides application management, yet both functions can co-exist on one hardware unit. Any standards-based server is recommended.
For parameters related to Avaya Media Server information, see Chapter 4: Avaya Aura Communication
Manager Administration , and the administration documentation for your call server. For parameters
related to DHCP and file servers, see
Chapter 5: Server Administration .
CAUTION:
!
CAUTION:
The deskphones obtain important information from the script files on the file server and depend on the application file for software upgrades. If the DHCP file server is unavailable when the deskphones reset, the deskphones register with the media server and operate. Some features might not be available. To restore them you need to reset the deskphone(s) when the file server is available.
DHCP Server
Avaya recommends that a DHCP server and application be installed and that static addressing be
avoided. Install the DHCP server and application as described in DHCP and File Servers on page 37.
HTTP/HTTPS Server
16 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Required Network Information
Required Network Information
Before you administer DHCP and HTTP, and TLS, as applicable, complete the information in
you have more than one Gateway, HTTP/TLS server, subnetwork mask, and Gatekeeper in your configuration, complete
for each DHCP server.
The 1600 Series IP Deskphones support specifying a list of IP addresses for a gateway/router, HTTP/
HTTPS server, and Avaya Media Server Gatekeeper(s). Each list can contain up to 255 total ASCII characters, with IP addresses separated by commas with no intervening spaces. Depending on the specific DHCP application, only 127 characters might be supported.
When specifying IP addresses for the file server or media server, use either dotted decimal format
(“xxx.xxx.xxx.xxx”) or DNS names. If you use DNS, the system value DOMAIN is appended to the IP addresses you specify. If DOMAIN is null, the DNS names must be fully qualified, in accordance with
IETF RFCs 1034 and 1035. For more information about DNS, see
and DNS Addressing on page 75.
Table 3: Required Network Information Before Installation - Per DHCP Server
1. Gateway (router) IP address(es)
2. HTTP server IP address(es)
3. Subnetwork mask
4. Avaya Media Server Gatekeeper IP address(es)
5. Avaya Media Server Gatekeeper port Although this can be a value between 0 and
65535, the default value is 1719. Do not change the default value unless that value conflicts with an existing port assignment.
6. HTTP server file path
7. Deskphone IP address range
From:
To:
8. DNS server address(es)
9. HTTPS server address(es)
If applicable.
If applicable.
The file server file path is the “root” directory used for all transfers by the server. All files are uploaded to or downloaded from this default directory. In configurations where the upgrade script and application
files are in the default directory, do not use item 6 in Table 3 .
As the LAN or System Administrator, you are also responsible for:
● Administering the DHCP server as described in
Chapter 5: Server Administration .
● Editing the configuration file on the applicable HTTP or HTTPS file server, as covered in
Series IP Deskphone Scripts and Application Files .
Issue 5 May 2014 17
Network Requirements
Other Network Considerations
SNMP
The 1600 Series IP Deskphones are fully compatible with SNMPv2c and with Structure of Management
Information Version 2 (SMIv2). The deskphones respond correctly to queries from entities that comply with earlier versions of SNMP, such as SNMPv1. “Fully compatible” means that the deskphones respond to queries directed either at the MIB-II or the read-only Custom MIB. Read-only means that the values therein cannot be changed externally by means of network management tools.
You can use the system value SNMPADD to restrict the IP addresses from which the deskphone accepts SNMP queries. You can also customize your community string with the system value
SNMPSTRING. For more information, see Chapter 5: Server Administration and
IP Deskphone Customizable System Parameters
.
Note:
Note:
As of Release 1.0, SNMP is disabled by default. Administrators must initiate SNMP by setting the SNMPADD and SNMPSTRING system values appropriately.
For more information about SNMP and MIBs, see the IETF references listed in
Appendix B: Related Documentation
. The Avaya Custom MIB for the 1600 Series IP Deskphones is available for download in *.txt format on the Avaya support Web site at http://www.avaya.com/support .
18 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Other Network Considerations
Reliability and Performance
All 1600 Series IP Deskphones respond to a ping or traceroute message sent from the DEFINITY
®
,
MultiVantage™, Avaya Aura Communication Manager, or Avaya Aura Communication Manager
Branch system (formerly known as Avaya Distributed Office) or any other network source. The deskphones do not originate a ping or traceroute. The 1600 Series IP Deskphones offer and support
“remote ping” and “remote traceroute.” The switch can instruct the deskphone to originate a ping or a traceroute to a specified IP address. The deskphone carries out that instruction and sends a message to the switch indicating the results. For more information, see your switch administration documentation.
If applicable, the deskphones test whether the network Ethernet switch port supports IEEE 802.1P/Q
tagged frames by ARPing the router with a tagged frame. For more information, see VLAN
Considerations on page 72. If your LAN environment includes Virtual LANs (VLANs), your router must
respond to ARPs for VLAN tagging to work properly.
QoS
For more information about the extent to which your network can support any or all of the QoS initiatives, see your LAN equipment documentation. See
QoS on page 28 about QoS implications for
the 1600 Series IP Deskphones.
All 1600 Series IP Deskphones provide some detail about network audio quality. For more information see,
Network Audio Quality Display on 1600 Series IP Deskphones on page 20.
IEEE 802.1P and 802.1Q
For more information about IEEE 802.1P and IEEE 802.1Q and the 1600 Series IP Deskphones, see
VLAN Considerations on page 72. Three bits of the 802.1Q
tag are reserved for identifying packet priority to allow any one of eight priorities to be assigned to a specific packet.
●
●
●
●
●
●
●
●
7: Network management traffic
6: Voice traffic with less than 10ms latency
5: Voice traffic with less than 100ms latency
4: “Controlled-load” traffic for critical data applications
3: Traffic meriting “extra-effort” by the network for prompt delivery, for example, executive e-mail
2: Reserved for future use
0: The default priority for traffic meriting the “best-effort” for prompt delivery of the network.
1: Background traffic such as bulk data transfers and backups
Issue 5 May 2014 19
Network Requirements
Note:
Note:
Priority 0 is a higher priority than Priority 1.
Network Audio Quality Display on 1600 Series IP Deskphones
All 1600 Series IP Deskphones give the user an opportunity to monitor network audio performance while on a call. For more information, see the deskphone user guide.
While on a call, the deskphones display network audio quality parameters in real-time, as shown in
:
Table 4: Parameters in Real-Time
Parameter
Received Audio Coding
Packet Loss
Packetization Delay
One-way Network Delay
Network Jitter
Compensation Delay
Possible Values
G.711, G.711u, G.711a, G.726, G.729A, or G.729B.
"No data" or a percentage. Late and out-of-sequence packets are counted as lost if they are discarded. Packets are not counted as lost until a subsequent packet is received and the loss confirmed by the RTP sequence number.
"No data" or an integer number of milliseconds. The number reflects the amount of delay in received audio packets, and includes any potential delay associated with the codec.
"No data" or an integer number of milliseconds. The number is one-half the value RTCP computes for the round-trip delay.
"No data" or an integer number of milliseconds reporting the average delay introduced by the jitter buffer of the deskphone.
The implication for LAN administration depends on the values the user reports and the specific nature of your LAN, like topology, loading, and QoS administration. This information gives the user an idea of how network conditions affect the audio quality of the current call. Avaya assumes you have more detailed tools available for LAN troubleshooting.
IP Address Lists and Station Number Portability
The 1600 Series IP Deskphones provide the capability to specify IP address lists. On startup or a reboot, the deskphone attempts to establish communication with these various network elements in turn. The deskphone starts with the first address on the respective list. If the communication is denied or times out, the deskphone proceeds to the next address on the appropriate list and tries that one. The deskphone does not report failure unless all the addresses on a given list fail, thereby improving the reliability of IP telephony.
20 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Other Network Considerations
This capability also has the advantage of making station number portability easier. Assume a situation where the company has multiple locations in London and New York, all sharing a corporate IP network.
Users want to take their deskphones from their offices in London and bring them to New York. When users start up their deskphones in the new location, the local DHCP server usually routes them to the local call server. With proper administration of the local DHCP server, the deskphone knows to try a second call server IP address, this one in London. The user can then be automatically registered with the London call server.
Chapter 5: Server Administration
contains details on administration of DHCP servers for lists of
alternate media servers, router/gateways, and HTTP/HTTPS servers. For more information, see DNS
TCP/UDP Port Utilization
The 1600 Series IP Deskphones use a variety of protocols, particularly TCP and UDP, to communicate with other equipment in the network. Part of this communication identifies which TCP or UDP ports each piece of equipment uses to support each protocol and each task within the protocol. For additional
TCP/UDP port utilization information as it applies to Avaya Aura Communication Manager, see UDP
Depending on your network, you might need to know what ports or ranges are used in the operation of
1600 Series IP Deskphones. Knowing these ports or ranges helps you administer your networking infrastructure.
● The box on the left always represents the 1600 Series IP Deskphone.
● Depending on the diagram, the boxes on the right refer to various pieces of network equipment with which the deskphone can communicate.
) represent the direction(s) of socket initialization. ● Open-headed arrows (for example,
● Closed-headed arrows (for example, of data transfer.
) represent the direction(s)
● The text the arrows point to identifies the port or ports that the 1600 Series IP Deskphones support for the specific situation. Brackets identify ranges when more than one port applies. The text indicates any additional qualifications or clarifications. In many cases, the ports used are the ones called for by IETF or other standards bodies.
Issue 5 May 2014 21
Network Requirements
Figure 1: Signaling, Audio and Management Diagram
Signaling, Audio and Management
1600 Series IP
Deskphone
Port: 49300
Port: [1500–6500] randomly selected
H.323 RAS (UDP/IP)
H.323 Signaling (TCP/IP)
Port: [4000–10000] randomly selected; range may be changed via
Gatekeeper administration; always an even number
Port: audio port + 1
(only active during a call if RTCP is enabled)
RTP Audio (UDP/IP)
RTCP (UDP/IP)
Port: audio port + 2
(only active during a call if RTCP monitoring is enabled)
Port:161
RTCP (UDP/IP)
SNMP (UDP/IP)
H.323 Gatekeeper
Port: 1719
Port: 1720
Media Gateway or another IP endpoint
Port selected from the audio port range administered for the network region
Port: audio port + 1
Voice Monitoring
Manager
Port depends on Voice
Monitoring Manager admin
SNMP MIB Viewer
Port depends on
MIB viewer admin
22 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Other Network Considerations
Figure 2: Initialization and Address Resolution Diagram
Initialization and Address Resolution
1600 Series IP
Deskphone
Port: 68
DHCP (TCP/IP)
DHCP Server
Port: 67
HTTPS Read Request (TCP/IP)
Port: [1024 - 5000]
Operating System
–selected (a new port is used for each file requested)
HTTPS Data, ACKs & Errors (TCP/IP)
HTTPS Server
Port:411
Port: Operating
System – selected (a new port is used for each file
HTTP Read Request (TCP/IP)
Port: [1024 - 5000]
Operating System – selected (a new port
is used for each file requested)
HTTPS Data, ACKs & Errors (TCP/IP)
HTTP Server
Port: 80
Port: Operating System
– selected (a new port is used for each file)
DNS(UDP/IP)
DNS Server
Port: 53 Port: [1024 - 5000]
Operating System
Issue 5 May 2014 23
Network Requirements
Security
For information about toll fraud, see the DEFINITY
®
, Avaya Aura Communication Manager, or Avaya
Aura Communication Manager Branch documents on the Avaya support Web site. The 1600 Series IP
Deskphones cannot guarantee resistance to all Denial of Service attacks. However, there are checks and protections to resist such attacks while maintaining appropriate service to legitimate users.
You also have a variety of optional capabilities to restrict or remove how crucial network information is displayed or used. These capabilities are covered in more detail in
Chapter 5: Server Administration
.
● Support signaling channel encryption while registering, and when registered, with appropriately administered Avaya Media Servers.
Note:
Note:
Signaling and audio are not encrypted when unnamed registration is effective.
● Restricting the response of the 1600 Series IP Deskphones to SNMP queries to only IP addresses on a list you specify.
● Specifying an SNMP community string for all SNMP messages the deskphone sends.
● Restricting dialpad access to Local Administration Procedures, such as specifying IP addresses, with a password.
● Removing dialpad access to most Local Administration Procedures.
● Restricting the end user’s ability to use a deskphone Options application to view network data.
As of Release 1.1, three existing security-related parameters can be administered on the call server and downloaded with encrypted signaling, in addition to unencrypted HTTP or encrypted HTTPS.
Those parameters are SNMP community string, SNMP Source IP Addresses, and Craft Access Code
(PROCPSWD).
Registration and Authentication
The Avaya Media Server supports using the extension and password to register and authenticate 1600
Series IP Deskphones. For more information, see the current version of your call server administration manual.
24 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Chapter 4: Avaya Aura Communication Manager
Administration
Call Server Requirements
Before you perform administration tasks, ensure that the proper hardware is in place, and your call server software is compatible with the 1600 Series IP Deskphones. Avaya recommends the latest PBX software and the latest IP deskphone firmware.
Switch Compatibility and Aliasing IP Deskphones
As of Release 1.1, 1600 Series IP Deskphones were natively supported by Avaya Aura Communication
Manager Release 5.2. Native support means that if you have Avaya Aura Communication Manager
Release 5.2, you:
● do not have to alias 1600 Series IP Deskphones,
● can add up to two BM32 Button Modules on each 1616 Series IP Deskphone, and
● can administer a call coverage deskphone number on a station-by-station basis.
If you have Avaya Aura Communication Manager Release 5.1 or earlier, you must alias the deskphones as follows:
1600 Series
Deskphone Model Aliased as...
1603
1603-I
1603SW
1603SW-I
1608
4610
4610
4610
4610
4610
Earliest Avaya Aura
Communication Manager Release
Avaya Aura Communication
Manager 3.0
Avaya Aura Communication
Manager 3.0
Avaya Aura Communication
Manager 3.0
Avaya Aura Communication
Manager 3.0
Avaya Aura Communication
Manager 3.0
Issue 5 May 2014 25
Avaya Aura Communication Manager Administration
1600 Series
Deskphone Model
1608-I
1616
1616-I
BM32
Aliased as...
4610
4620
4620
EU24
Earliest Avaya Aura
Communication Manager Release
Avaya Aura Communication
Manager 3.0
Avaya Aura Communication
Manager 3.0
Avaya Aura Communication
Manager 3.0
Avaya Aura Communication
Manager 3.0
The 1603, 1603SW, 1603-I, and 1603SW-I IP Deskphones support three administrable call appearances or feature buttons. The 1608 and 1608-I IP Deskphones support eight administrable call appearances or feature buttons. The 1616 and 1616-I IP Deskphones support 16 administrable call appearances or feature buttons. In addition, the 1616/1616-I IP Deskphones support the BM32 Button
Module. The 1616/1616-I always support a single BM32, and with Avaya Aura Communication
Manager Release 5.2 or later, support up to two BM32 Button Modules per deskphone.
Note:
Note:
Using one BM32 can be supported by PoE. If you use a second button module, you must use the Avaya approved external auxiliary 5V power supply for the 1616/1616-I IP
Deskphone. While the auxiliary power supply can support up to three BM32 button modules, Communication Manager Release 5.2 can only configured to support up to two
BM32.
The BM32 Button Module provides another 32 administrable call appearances and features. When attached to a 1616/1616-I IP Deskphone that is aliased as a 4620, the first 16 administered call appearances and features are placed directly on the deskphone, and the next 32 administered call appearances and features are placed on the button module, for a total of 48 administrable buttons.
For more information about aliasing one deskphone model as another, see “Using an Alias” in the
Administrator Guide for Avaya Aura™ Communication Manager (Document 03-300509).
Avaya Aura Communication Manager Branch systems provide native support for the 1600 Series
Deskphones. See the Avaya Aura Communication Branch Device Manager online help for more information.
26 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Media Server (Switch) Administration
Media Server (Switch) Administration
If you are using the 1600 Series IP Deskphones with Avaya Aura Communication Manager, see the following documents on the Avaya support Web site for information about specific switch administration:
● The Administrator Guide for Avaya Aura™ Communication Manager (Document 03-300509) provides detailed instructions for administering an IP deskphone system on Avaya Aura
Communication Manager. See Chapter 3 “Managing Deskphones,” which describes the process of adding new deskphones. Also, you can locate pertinent screen illustrations and field descriptions in Chapter 19 “Screen References” of that guide.
● Administration for Network Connectivity for Avaya Aura™ Communication Manager (Document
Number 555-233-504) provides detailed information about switch administration for your network.
If you are using the 1600 Series IP Deskphones with Avaya Aura Communication Manager Branch, see the Avaya Aura Communication Manager Branch Device Manager online help for information about specific switch administration.
IP Interface and Addresses
If you are using the 1600 Series IP Deskphones with Avaya Aura Communication Manager, follow these general guidelines:
● Define the IP interfaces for each CLAN and Media processor circuit pack on the switch that uses the IP Interfaces screen. For more information, see Administration for Network Connectivity for
Avaya Aura™ Communication Manager (Document 555-233-504).
● On the Customer Options form, verify that the IP Stations field is set to “y” (Yes). If it is not, contact your Avaya sales representative. The IP Softphone field does not have to be set to “y”
(Yes).
If you are using the 1600 Series IP Deskphones with Avaya Aura Communication Manager Branch, see the Avaya Aura Communication Manager Branch Device Manager online help for information about administering these deskphones.
Issue 5 May 2014 27
Avaya Aura Communication Manager Administration
UDP Port Selection
The 1600 Series IP Deskphones can be administered from the Avaya Aura Communication Manager
Network Region form to support UDP port selection. Locate specific port assignment diagrams in the
1600 IP Deskphone Installation and Maintenance Guide. For information about Avaya Aura
Communication Manager implementation, see Administration for Network Connectivity for Avaya
Aura™ Communication Manager (Document Number 555-233-504) on the Avaya support Web site.
Administer the switch to use a port within the proper range for the specific LAN, and the IP deskphone(s) copy that port. If no UDP port range is administered on the switch, the IP deskphone uses an even-numbered port, randomly selected from the interval 4000 to 10000.
RSVP and RTCP
Avaya IP Deskphones implement the Resource ReSerVation Protocol (RSVP) administered from the media server and the RTP Control Protocol (RTCP). The Avaya Voice over IP (VoIP) Monitoring
Manager (VMON) software can then provide real-time monitoring and historical data of audio quality for
VoIP calls.
The only way to change these parameters is by appropriate switch administration. For more information, see your Avaya Media Server administration documentation and Administration for
Network Connectivity for Avaya Aura™ Communication Manager (Document Number 555-233-504).
QoS
The 1600 Series IP Deskphones support both IEEE 802.1P/Q and DiffServ. Other network-based QoS initiatives such as UDP port selection do not require support by the deskphones. However, they contribute to improved QoS for the entire network.
IEEE 802.1P and 802.1Q
The 1600 Series IP Deskphones can simultaneously support receipt of packets using, or not using,
802.1Q parameters. To support IEEE 802.1P/Q, you can administer 1600 Series IP Deskphones from the network by appropriate administration of the DHCP or HTTP/HTTPS servers, or by using dialpad input at the deskphone.
Important:
!
Important:
Avaya Aura Communication Manager administration always takes precedence over manual administration of IEEE 802.1P/Q data.
28 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Media Server (Switch) Administration
The four IEEE 802.IP/Q QoS parameters in the deskphones that can be administered on the IP
Network Region form are L2Q, L2QVLAN, L2QAUD, and L2QSIG. To set these parameters at the switch, see “About Quality of Service (QoS) and voice quality administration” in Administration for
Network Connectivity for Avaya Aura™ Communication Manager (Document Number 555-233-504).
To set these parameters manually see the 1600 IP Deskphone Installation and Maintenance Guide.
You can specify VLAN ID and VLANTEST values with the ADDR Local Administrative Option.
Note:
Note:
All local administrative procedures are on a phone-by-phone basis. Administration using
Avaya Aura Communication Manager, DHCP, and HTTP applies to the deskphone system itself or to a range of deskphones.
NAT
Network Address Translation (NAT) usage can lead to problems that affect the consistency of addressing throughout your network. All H.323 IP Deskphones support NAT interworking. Support for
NAT does not imply support for Network Address Port Translation (NAPT). The deskphones do not support communication to the PBX through any NAPT device.
NAT requires specific administration on the media server. A direct Avaya IP Deskphone-to-Avaya IP
Deskphone call with NAT requires Avaya Aura Communication Manager Release 3.0 or greater software. For more information, see Administration for Network Connectivity for Avaya Aura™
Communication Manager (Document Number 555-233-504) on the Avaya support Web site.
DIFFSERV
The DiffServ values change to the values administered on the media server as soon as the deskphone registers. For more information, see Chapter 4 “Network Quality Administration” in Administration for
Network Connectivity for Avaya Aura™ Communication Manager (Document Number 555-233-504).
Unless there is a specific need in your enterprise LAN, Avaya recommends that you do not change the default values.
Issue 5 May 2014 29
Avaya Aura Communication Manager Administration
Voice Mail Integration
1600 Series IP Deskphones with Avaya Aura Communication
Manager 5.2 Native Support
Release 1.1 provides native support for 1600 Series IP Deskphones running on Avaya Aura
Communication Manager Release 5.2 or later. When native support applies, pressing the Messages button causes the deskphone to first determine if the call server has a dedicated number for retrieving voice mail and when found, to proceed with voice mail retrieval.
1600 Series IP Deskphones Aliased as 4600 Series IP Deskphones
When native support does not apply, 1600 Series IP Deskphones are aliased as 4600 Series IP
Deskphones and run under an Avaya Aura Communication Manager Release earlier than 5.2. In this case, use the settings file to configure the Messages button by setting the system parameter
to any dialable string. MSGNUM examples are:
● a standard deskphone number the deskphone should dial to access your voice mail system, such as AUDIX or Octel.
● a Feature Access Code (FAC) that allows users to transfer an active call directly to voice mail.
FACs are supported only for QSIG-integrated voice mail systems like AUDIX or Octel. QSIG is an enhanced signaling system that allows the voice mail system and Avaya Aura Communication
Manager Automated Call Processing (ACP) to exchange information.
When the user presses the Messages button on the deskphone, that number or FAC is automatically dialed, giving the user one-touch access to voice mail.
The settings file specifies the deskphone number to be dialed automatically when the user presses this button. The command is:
SET MSGNUM 1234 where 1234 is the Voice Mail extension (Avaya Aura Communication Manager hunt group or VDN). For more information, see
.
MSGNUM is used both in native support and when the deskphone is aliased using non-native support.
Messaging must be configured for native support.
A separate Voice Mail extension can be administered for each station.
30 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Deskphone Administration
Deskphone Administration
This section describes how to administer Avaya Aura Communication Manager for 1600 Series IP
Deskphones. For detailed information about administering Avaya Aura Communication Manager, see the following Avaya documents:
●
●
Administrator Guide for Avaya Aura™ Communication Manager (Document 03-300509).
Feature Description and Implementation for Avaya Aura™ Communication Manager (Document
555-245-770).
For detailed information about administering Avaya Aura Communication Manager Branch for 1600
Series IP Deskphones, see the Avaya Aura Communication Manager Branch Device Manager online help.
System-Wide Administration
This section refers to Avaya Aura Communication Manager administration on the Switch Administration
Terminal (SAT) or by Avaya Site Administration. The system wide Avaya Aura Communication Manager form and the particular page that needs to be administered for each feature are provided. These features, which already exist, are not required but are recommended because they optimize the deskphone user interface. Avaya Aura Communication Manager Release 3.0 or greater is required.
Note:
Note:
See Appendix C: Sample Administration Forms for illustrated examples of the pages
used to administer Avaya Aura Communication Manager features.
Feature-Related System Parameters
Release 1.1 supports the functionality introduced on Avaya Aura Communication Manager Release 5.2 that allows call server administration of three system-wide parameters. By administering these parameters on Avaya Aura Communication Manager, they can be automatically downloaded to the deskphone during registration, instead of or in addition to from the settings file or locally per deskphone. The three system parameters are: SNMP community string, SNMP Source IP addresses,
Issue 5 May 2014 31
Avaya Aura Communication Manager Administration and Craft Access Code (PROCPSWD). Administer these three parameters using Page 3 of the change system-parameters ip-options form.
Avaya Aura Communication Manager Feature Administration
Feature
On-Hook Dialing
Auto Hold
Coverage Path
Enhanced Conference
Features
Administration
Set up Avaya Aura Communication Manager so that the phone supports on-hook dialing. Use the System Parameters Features form page 10. Use the command Change system-parameters features to view the form and make the change.
Set up Avaya Aura Communication Manager to enable Auto
Hold, so that the phone automatically places an active call on hold when the user answers or resumes a call on another call appearance. Use the System Parameters Features form, page 6 .
Administer a coverage path for both phone demonstration and normal operations. Use the Coverage Path form and give it a number, for example, Coverage path 1. If Voice Mail is available, this is also where you administer the hunt group or VDN, depending on the type of Voice Mail system being used.
Enable enhanced conference display to support the user experience for conferences. Block Enhanced Conference Display on the Class of Restriction (COR) form must be set to No. Use the command Change COR, followed by a number, to view the form and make the change. a sample of the Class of Restriction form.
Administering Stations
This section refers to Avaya Aura Communication Manager administration on the Switch Administration
Terminal (SAT) or by Avaya Site Administration. Administer the following items on the Station form, sample screens of which are provided in
through Figure 4 . Avaya recommends setting the
features covered in this section because they optimize the user interface.
Release 1.1 supports the functionality introduced on Avaya Aura Communication Manager Release 5.2 that allows call server administration of the GROUP parameter on a station-by-station basis. As covered in
The GROUP System Value on page 59, the GROUP Identifier can be used in conjunction
with the 46xxsettings file to allow administration to apply to specific “groups” of deskphones. Before
Release 1.1, the Group Identifier had to be administered locally on each applicable deskphone. As of
Release 1.1, the Group Identifier can be administered centrally, and downloaded to each applicable deskphone. The GROUP ID parameter is administered on page 3 of the Change Station Form. Once downloaded, the Group Identifier takes effect starting with the next deskphone boot-up.
For sample Station Forms, see
Appendix C: Sample Administration Forms
.
32 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Administering Stations
Aliasing 1600 Series IP Deskphones
Avaya Aura Communication Manager releases earlier than 5.2 do not provide native support for 1600
Series IP Deskphones. On the Station Form, administer (alias) the deskphones as follows:
Change Alias Station:
●
●
●
Alias set up type 1603/1603SW/1603-I/1603SW-I to a 4610
Alias set up type 1608/1608-I to a 4610
Alias set up type 1616/1616-I to a 4620SW/4621SW
Avaya Aura Communication Manager Release 5.2 (and later) provides native support for the
1603,1603SW, 1603-I, 1603SW-I, 1608, 1608-I, 1616, and 1616-I.
Administering Features
The following are administrable Station Features that Avaya recommends you administer for your 1600
Series IP Deskphones for maximum user experience.
Administrable Station Features
Feature
Enhanced Conference
Features
Far End Mute
Send All Calls (SAC)
Coverage Path
Auto select any idle
appearance
Restrict Last Call
Appearance
Conference/Transfer on
Primary Appearance
Administration
Administer Conf-dsp (conference display) on the station form as a feature button. Doing so turns on enhanced conference features and gives users advanced conference features.
Administer fe-mute (far end mute). When this is enabled the phone shows a “Silence” softkey on the Conference details screen. This feature works only for trunk calls.
On the Station form, administer SAC (send-calls) as a feature button. On the Station form to the right of where send all calls is administered, leave the extension box empty. This feature requires a coverage path to be administered on the station form.
For normal operation, you must set up a coverage path for each deskphone. Administer the Station form to point to the appropriate system coverage path, for example, coverage path 1.
Set Auto select any idle appearance to N (no) to optimize answering calls.
Set Restrict Last Call Appearance to Y (yes).
Set Conference/Transfer on Primary Appearance to Y (yes) to ensure that conference/transfer of a bridged appearance works properly.
Issue 5 May 2014 33
Avaya Aura Communication Manager Administration
Feature Buttons and Call Appearances
For the 1603/1603SW/1603-I/1603SW-I and 1608/1608-I IP
Deskphones
You can administer Feature/Call Appearance Buttons 1 – 8 on the Avaya Aura Communication
Manager Station form, which the deskphone Feature screen then displays in sequence. The deskphone does not display any of the Feature Button labels administered on buttons 9 – 24. These deskphones do not support the BM32 Button Module.
For the 1616/1616-I IP Deskphones
You can administer Feature/Call Appearance Buttons 1 – 16 on the Avaya Aura Communication
Manager Station form. The features administered on the Station form appear in the same sequence on the deskphone Feature screen. Features administered on the Expansion Module BM32 Call
Appearance buttons display on the deskphone Features screen following the first 16 administered feature buttons. All administered BM32 Button Labels (Call Appearances and Feature Buttons) display on the corresponding BM32 module buttons.
In Table 5 the term “phone screen” refers to either the call appearance screen or the features screen, as applicable to the button type.
Table 5: Station Form Administration Results
Feature / Call Appearance (CA) /
Bridged Call Appearance (BA) buttons on the Station form...
Is displayed on the phone as:
1
2 to 16
17 to 48
49 to 80
1603/1603SW
1603-I/1603SW-I
Phone screen
CAs/BAs on
Phone screen; must scroll to see more than 1
N/A
N/A
1608/1608-I
Phone screen
CAs/BAs on
Phone screen; must scroll to see more than 1
N/A
N/A
1616/1616-I
Phone screen
CAs/BAs on
Phone screen; must scroll to see more than 1
First BM32
Second BM32
34 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Shuffling
For additional information about administering the call server for 1600 Series IP Deskphones, see the following Avaya documents, available on the Avaya Support Web site:
●
●
Administrator Guide for Avaya Aura™ Communication Manager (Document Number 03-300509).
Feature Description and Implementation for Avaya Aura™ Communication Manager (Document
Number 555-245-770).
Conference Details Screen for Ad-Hoc Conferences
Conference Details allows the user to view parties on a conference call and selectively mute or drop individual parties for a conference call setup.
If administered on an Expansion Module button, the BM32 Button Module must be connected.
To enable Conference Details capabilities:
1. On the Class of Restriction (COR) form make sure that Block Enhanced Conference/Transfer
Displays is set to No.
2. As described in On-Hook Dialing , administer the Conference Display Feature Button to a Phone button on the Phone screen.
Shuffling
Administer shuffling on three forms:
● Feature-Related Parameters form, shown in
. Set the Direct IP-IP Audio Connections? field to y (yes).
● IP Network Region form, shown in
Figure 9 . Set both the Intra-region IP-IP Direct Audio field
and the Inter-region IP-IP Direct Audio field to y (yes).
●
Station form, shown in Figure 2
. Set the Direct IP-to-IP Audio Connection to y (yes). The Station form setting overrides the network region, which overrides the system setting.
Issue 5 May 2014 35
Avaya Aura Communication Manager Administration
Printing Button Labels
You can download software from www.desi.com that enables you to print button labels for the 1600 series deskphones. To download this software, perform the following steps:
1. Using your web browser, go to www.desi.com.
2. Click DESI downloads.
3. Download the appropriate application.
If you are using Avaya Aura Communication Manager Branch, you can export the button settings from
Local Manager and import the settings into the DESI application. For more information, see the Avaya
Aura Communication Manager Branch Device Manager online help.
36 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Chapter 5: Server Administration
Software Checklist
Ensure that you own licenses to use the DHCP, HTTP, and HTTPS server software.
Note:
CAUTION:
Note:
You can install the DHCP and HTTP server software on the same machine.
!
CAUTION:
The firmware in the 1600 Series IP Deskphones reserves IP addresses of the form
192.168.0.24 and 192.168.1.x for internal communications. The deskphone(s) improperly use addresses you specify if they are of that form.
DHCP and File Servers
Dynamic Host Configuration Protocol (DHCP) minimizes maintenance for a 1600 Series IP Deskphone network by removing the need to individually assign and maintain IP addresses and other parameters for each IP deskphone on the network.
The DHCP server provides the following information to the 1600 Series IP Deskphones:
● IP address of the 1600 Series IP Deskphone(s)
● IP address of the Gatekeeper board on the Avaya Media Server
● IP address of the HTTP or HTTPS server
● The subnet mask
● IP address of the router
● DNS Server IP address
Administer the LAN so each IP deskphone can access a DHCP server that contains the IP addresses and subnet mask.
The IP deskphone cannot function without an IP address. The failure of a DHCP server at boot time leaves all the affected deskphones unusable. A user can manually assign an IP address to an IP deskphone. When the DHCP server finally returns, the deskphone never looks for a DHCP server unless the static IP data is unassigned manually. In addition, manual entry of IP data is an error-prone process.
Issue 5 May 2014 37
Server Administration
Avaya recommends that:
● A minimum of two DHCP servers be available for reliability.
● A DHCP server be available when the IP deskphone reboots.
● A DHCP server be available at remote sites if WAN failures isolate IP deskphones from the central site DHCP server(s).
The file server provides the 1600 Series IP Deskphone with a script file and, if appropriate, new or updated application software. See
Step 3: Deskphone and File Server
. In addition, you can edit an associated settings file to customize deskphone parameters for your specific environment. For more information, see
DHCP Server Administration
This document concentrates on the simplest case of the single LAN segment. Information provided here can be used for more complex LAN configurations.
CAUTION:
!
CAUTION:
Before you start, understand your current network configuration. An improper installation can cause network failures or reduce the reliability and performance of your network.
DHCP Generic Setup
This document is limited to describing a generic administration that works with the 1600 Series IP
Deskphones. Three DHCP software alternatives are common to Windows operating systems:
● Windows NT
®
4.0 DHCP Server
● Windows 2000
®
DHCP Server
● Windows 2003
®
DHCP Server
38 1600 Series IP Deskphone Administrator Guide Release 1.3.5
DHCP Server Administration
Any other DHCP application might work. It is the responsibility of the customer to install and configure the DHCP server correctly.
DHCP server setup involves:
1. Installing the DHCP server software according to vendor instructions.
2. Configuring the DHCP server with:
● IP addresses available for the 1600 Series IP Deskphones.
● The following DHCP options:
- Option 1 - Subnet mask.
As described in
- Option 3 - Gateway (router) IP address(es).
As described in Table 3 , item 1. If using more than one address, the total list can contain up to
255 total ASCII characters. You must separate IP addresses with commas with no intervening spaces.
- Option 6 - DNS server(s) address list.
If using more than one address, the total list can contain up to 127 total ASCII characters. You must separate IP addresses with commas with no intervening spaces. At least one address in
Option 6 must be a valid, non zero, dotted decimal address.
- Option 12 - Host Name.
Value is AVohhhhhh, where: o is “A” if the OID (first three octets) of the MAC address for the deskphone is 00-04-0D. “E” if the OID is 00-09-6E, “L” if the OID is 00-60-1D, and “X” if the
OID is anything else and where hhhhhh are ASCII characters for the hexadecimal representation of the last three octets of the MAC address for the deskphone.
- Option 15 - DNS Domain Name.
This string contains the domain name to be used when DNS names in system parameters are resolved into IP addresses. This domain name is appended to the DNS name before the 1600
IP Deskphone attempts to resolve the DNS address. Option 15 is necessary if you want to use a DNS name for the HTTP server. Otherwise, you can specify a DOMAIN as part of customizing HTTP as indicated in
- Option 51 - DHCP lease time.
If this option is not received, the DHCPOFFER is not be accepted. Avaya recommends a lease time of six weeks or greater. If this option has a value of FFFFFFFF hex, the IP address lease is assumed to be infinite as per RFC 2131, Section 3.3, so that renewal and rebinding procedures are not necessary even if Options 58 and 59 are received. Expired leases cause
Avaya IP Deskphones to reboot. Avaya recommends providing enough leases so an IP address for an IP deskphone does not change if it is briefly taken offline.
Issue 5 May 2014 39
Server Administration
Note:
Note:
The DHCP standard states that when a DHCP lease expires, the device should immediately cease using its assigned IP address. If the network has problems and the only DHCP server is centralized, the server is not accessible to the given deskphone. In this case the deskphone is not usable until the server can be reached.
Avaya recommends, once assigned an IP address, the deskphone continues using that address after the DHCP lease expires, until a conflict with another device is detected. As
Table 9: 1600 Series IP Deskphone Customizable System Parameters
indicates, the system parameter DHCPSTD allows an administrator to specify that the deskphone will either: a). Comply with the DHCP standard by setting DHCPSTD to “1”, or b). Continue to use its IP address after the DHCP lease expires by setting DHCPSTD to
“0.”
The latter case is the default. If the default is invoked, after the DHCP lease expires the deskphone sends an ARP Request for its own IP address every five seconds.
The request continues either forever, or until the deskphone receives an ARP Reply.
After receiving an ARP Reply, the deskphone displays an error message, sets its IP address to 0.0.0.0, and attempts to contact the DHCP server again.
- Option 52 - Overload Option, if desired.
If this option is received in a message, the deskphone interprets the sname and file fields in accordance with IETF RFC 2132,
Section 9.3, listed in Appendix B: Related Documentation .
- Option 53 - DHCP message type.
Value is 1 (DHCPDISCOVER) or 3 (DHCPREQUEST).
- Option 55 - Parameter Request List.
Acceptable values are:
1 (subnet mask),
3 (router IP address[es])
6 (domain name server IP address[es])
15 (domain name)
NVSSON (site-specific option number)
- Option 57 - Maximum DHCP message size.
- Option 58 - DHCP lease renew time.
If not received or if this value is greater than that for Option 51, the default value of T1
(renewal timer) is used as per IETF RFC 2131, Section 4.5, listed in
- Option 59 - DHCP lease rebind time.
If not received or if this value is greater than that for Option 51, the default value of T2
(rebinding timer) is used as per RFC 2131, Section 4.5
40 1600 Series IP Deskphone Administrator Guide Release 1.3.5
DHCP Server Administration
The 1600 Series IP Deskphones do not support Regular Expression Matching, and therefore, do not use wildcards. For more information, see
Administering Options for the 1600 Series IP Deskphones on page 65.
In configurations where the upgrade script and application files are in the default directory on the HTTP server, do not use the HTTPDIR=<path>.
You do not have to use Option 242. If you do not use this option, you must ensure that the key information, especially HTTPSRVR and MCIPADD, is administered appropriately elsewhere.
Avaya recommends that you administer DHCP servers to deliver only the options specified in this document. Administering additional, unexpected options might have unexpected results, including causing the IP deskphone to ignore the DHCP server.
The media server name and HTTP server name must each be no more than 32 characters in length.
Examples of good DNS administration include:
- Option 6: “aaa.aaa.aaa.aaa”
- Option 15: “dnsexample.yourco.com,zzz.zzz.zzz.zzz”
- Option 242: “MCIPADD=xxxx.xxx.xxx.xxx”
Depending on the DHCP application you choose, be aware that the application most likely does not immediately recycle expired DHCP leases. An expired lease might remain reserved for the original client a day or more. For example, Windows NT
®
DHCP reserves expired leases for about one day. This reservation period protects a lease for a short time. If the client and the DHCP server are in two different time zones, the clocks of the computers are not in sync, or the client is not on the network when the lease expires, there is time to correct the situation.
The following example shows the implication of having a reservation period: Assume two IP addresses, therefore two possible DHCP leases. Assume three IP deskphones, two of which are using the two available IP addresses. When the lease for the first two deskphones expires, the third deskphone cannot get a lease until the reservation period expires. Even if the other two deskphones are removed from the network, the third deskphone remains without a lease until the reservation period expires.
Issue 5 May 2014 41
Server Administration
, the 1600 Series IP Deskphone sets the system values to the DHCPACK message field values shown.
Table 6: DHCPACK Setting of System Values
System Value
IPADD
NETMASK
GIPADD
TLSSRVR
HTTPSRVR
DNSSRVR
DOMAIN
DHCP lease time
DHCP lease renew time
DHCP lease rebind time
Set to
The yiaddr field.
Option #1 (if received).
Option #3 (if received, which might be a list of IP addresses).
The siaddr field, if that field is non-zero.
The siaddr field, if that field is non-zero.
Option #6 (if received, which might be a list of IP addresses).
Option #15 (if received).
Option #51 (if received).
Option #58 (if received).
Option #59 (if received).
The system values L2Q, L2QVLAN, and PHY2VLAN are not set from a name=value pair if those
system values were previously set by LLDP. For more information, see Link Layer Discovery Protocol
.
Windows NT 4.0 DHCP Server
Verifying the Installation of the DHCP Server
Use the following procedure to verify whether the DHCP server is installed.
1. Select Start-->Settings-->Control Panel.
2. Double-click the Network icon.
3. Verify that Microsoft DHCP Server is listed as one of the Network Services on the
Services tab.
4. If it is listed, continue with the next section. If it is not listed, install the DHCP server.
42 1600 Series IP Deskphone Administrator Guide Release 1.3.5
DHCP Server Administration
Creating a DHCP Scope for the IP Deskphones
Use the following procedure to create a DHCP scope for the IP deskphones.
1. Select Start-->Programs-->Admin Tools-->DHCP Manager.
2. Expand Local Machine in the DHCP Servers window by double clicking it until the + sign changes to a - sign.
3. Select Scope-->Create.
4. Using information recorded in
Table 3: Required Network Information Before Installation - Per
Define the Deskphone IP Address Range.
Set the Subnet Mask.
To exclude any IP addresses you do not want assigned to IP deskphones within the Start and
End addresses range: a. In the Exclusion Range Start Address field, enter the first IP Address in the range that you want to exclude.
b. In the Exclusion Range End Address field, enter the last IP Address in the range that you want to exclude.
c. Click the Add button.
d. Repeat steps a. through c. for each IP address range to be excluded.
Note:
Note:
Avaya recommends that you provision the 1600 Series IP Deskphones with sequential
IP addresses. Also do not mix 1600 Series IP Deskphones and PCs in the same scope.
5. Under Lease Duration, select the Limited To option and set the lease duration to the maximum.
6. Enter a sensible name for the Name field, such as “DEFINITY IP Deskphones.”
7. Click OK.
A dialog box prompts you: Activate the new scope now?
8. Click No.
Note:
Activate the scope only after setting all options.
Note:
Issue 5 May 2014 43
Server Administration
Editing Custom Options
Use the following procedure to edit custom options.
1. Highlight the newly created scope.
2. Select DHCP Options-->Defaults in the menu.
3. Click the New button.
4. In the Add Option Type dialog box, enter an appropriate custom option name, for example,
“1600OPTION.”
5. Change the Data Type Byte value to String.
6. Enter 242 in the Identifier field.
7. Click the OK button.
The DHCP Options menu displays.
8. Select the Option Name for 242 and set the value string.
9. Click the OK button.
10. For the Option Name field, select 003 Router from the drop-down list.
11. Click Edit Array.
12. Enter the Gateway IP Address recorded in Table 3: Required Network Information Before
Installation - Per DHCP Server
for the New IP Address field.
13. Select Add and then OK.
Adding the DHCP Option
Use the following procedure to add the DHCP option.
1. Highlight the scope you just created.
2. Select Scope under DHCP Options.
3. Select the 242 option that you created from the Unused Options list.
4. Click the Add button.
5. Select option 003 from the Unused Options list.
6. Click the Add button.
7. Click the OK button.
8. Select the Global parameter under DHCP Options.
9. Select the 242 option that you created from the Unused Options list.
10. Click the Add button.
11. Click the OK button.
44 1600 Series IP Deskphone Administrator Guide Release 1.3.5
DHCP Server Administration
Activating the Leases
Use the following procedure to activate the leases.
● Click Activate under the Scope menu.
The light-bulb icon for the scope lights.
Verifying Your Configuration
This section describes how to verify that the 1600OPTION is correctly configured for the Windows NT
®
4.0 DHCP server.
Note:
Note:
Although this configuration represents that for 1600 Series IP Deskphones, the file remains as 46XXOPTIONS. This allows shared use by 4600, 9600, and 1600 Series IP
Deskphones.
Verify the Default Option, 242 1600OPTION
1. Select Start-->Programs-->Admin Tools-->DHCP Manager.
2. Expand Local Machine in the DHCP servers window by double clicking until the + sign changes to a - sign.
3. In the DHCP servers frame, click the scope for the IP deskphone.
4. Select Defaults from the DHCP_Options menu.
5. In the Option Name pull-down list, select 242 1600OPTION.
6. Verify that the Value String box contains the correct string from DHCP Server Administration
.
If not, update the string and click the OK button twice.
Verify the Scope Option, 242 1600OPTION
1. Select Scope under DHCP OPTIONS.
2. In the Active Options: scroll list, click 242 1600OPTION.
3. Click the Value button.
4. Verify that the Value String box contains the correct string from
DHCP Generic Setup on page 38.
If not, update the string and click the OK button.
Issue 5 May 2014 45
Server Administration
Verify the Global Option, 242 1600OPTION
1. Select Global under DHCP OPTIONS.
2. In the Active Options: scroll list, click 242 1600OPTION.
3. Click the Value button.
4. Verify that the Value String box contains the correct value from DHCP Generic Setup on page 38.
If not, update the string and click the OK button.
Windows 2000 DHCP Server
Verifying the Installation of the DHCP Server
Use the following procedure to verify whether the DHCP server is installed.
1. Select Start-->Program-->Administrative Tools-->Computer Management.
2. Under Services and Applications in the Computer Management tree, find DHCP.
3. If DHCP is not installed, install the DHCP server. Otherwise, proceed directly to Creating and
for instructions on server configuration.
Creating and Configuring a DHCP Scope
Use the following procedure to create and configure a DHCP scope.
1. Select Start-->Programs-->Administrative Tools-->DHCP.
2. In the console tree, click the DHCP server to which you want to add the DHCP scope for the IP deskphones. This is usually the name of your DHCP server machine.
3. Select Action-->New Scope from the menu.
Windows displays the New Scope Wizard to guide you through rest of the setup.
4. Click the Next button.
The Scope Name dialog box displays.
5. In the Name field, enter a name for the scope such as “DEFINITY IP Deskphones,” then enter a brief comment in the Description field.
6. When you finish Steps 1 - 5, click the Next button.
The IP Address Range dialog box displays.
7. Define the range of IP addresses used by the IP deskphones listed in Table 3: Required Network
Information Before Installation - Per DHCP Server
. The Start IP Address is the first IP address available to the IP deskphones. The End IP Address is the last IP address available to the IP deskphones.
Note:
Note:
Avaya recommends not mixing 1600 Series IP Deskphones and PCs in the same scope.
8. Define the subnet mask in one of two ways:
46 1600 Series IP Deskphone Administrator Guide Release 1.3.5
DHCP Server Administration
● The number of bits of an IP address to use for the network/subnet IDs.
● The subnet mask IP address.
Enter only one of these values. When you finish, click the Next button.
The Add Exclusions dialog box displays.
9. Exclude any IP addresses in the range specified in the previous step that you do not want assigned to an IP deskphone.
a. In the Start Address field under Exclusion Range, enter the first IP Address in the range you want to exclude.
b. In the End Address field under Exclusion Range, enter the last IP Address in the range you want to exclude.
c. Click the Add button.
d. Repeat steps a. through c. for each IP address range that you want to exclude.
Note:
Note:
You can add additional exclusion ranges later by right clicking the Address Pool under the newly created scope and selecting the New Exclusion Range option.
Click the Next button after you enter all the exclusions.
The Lease Duration dialog box displays.
10. For all deskphones that obtain their IP addresses from the server, enter 30 days in the Lease
Duration field. This is the duration after which the IP address for the device expires and which the device needs to renew.
11. Click the Next button.
The Configure DHCP Options dialog box displays.
12. Click the No, I will activate this scope later button.
The Router (Default Gateway) dialog box displays.
13. For each router or default gateway, enter the IP Address and click the Add button.
When you are done, click the Next button.
The Completing the New Scope Wizard dialog box displays.
14. Click the Finish button.
The new scope appears under your server in the DHCP tree. The scope is not yet active and does not assign IP addresses.
15. Highlight the newly created scope and select Action-->Properties from the menu.
Issue 5 May 2014 47
Server Administration
CAUTION:
16. Under Lease duration for DHCP clients, select Unlimited and then click the OK button.
!
CAUTION:
IP address leases are kept active for varying periods of time. To avoid having calls terminated suddenly, make the lease duration unlimited.
Adding DHCP Options
Use the following procedure to add DHCP options to the scope you created in the previous procedure.
1. On the DHCP window, right-click the Scope Options folder under the scope you created in the last procedure.
A drop-down menu displays.
2. In the left pane of the DHCP window, right click the DHCP Server name, then click Set Predefined
Options....
3. Under Predefined Options and Values, click Add.
4. In the Option Type Name field, enter any appropriate name, for example, “Avaya IP
Deskphones.”
5. Change the Data Type to String.
6. In the Code field, enter 242, then click the OK button twice.
The Predefined Options and Values dialog box closes, leaving the DHCP dialog box enabled.
7. Expand the newly created scope to reveal its Scope Options.
8. Click Scope Options and select Action-->Configure Options from the menu.
9. In the General tab page, under the Available Options, check the Option 242 checkbox.
10. In the Data Entry box, enter the DHCP IP deskphone option string as described in
DHCP Generic Setup on page 38.
Note:
Note:
You can enter the text string directly on the right side of the Data Entry box under the
ASCII label.
11. From the list in Available Options, check option 003 Router.
12. Enter the gateway (router) IP Address from the IP address field of Table 3: Required Network
Information Before Installation - Per DHCP Server
.
13. Click the Add button.
14. Click the OK button.
48 1600 Series IP Deskphone Administrator Guide Release 1.3.5
HTTP Generic Setup
Activating the New Scope
Use the following procedure to activate the new scope.
1. In the DHCP console tree, click the IP Deskphone Scope you just created.
2. From the Action menu, select Activate.
The small red down arrow over the scope icon disappears, indicating that the scope was activated.
HTTP Generic Setup
You can store the same application software, script file, and settings file on an HTTP server as you can on a TFTP server. TFTP is not supported for 1600 Series IP Deskphones. With proper administration, the deskphone seeks out and uses that material. Some functionality might be lost by a reset if the
HTTP server is unavailable. For more information, see DHCP and File Servers on page 37.
CAUTION:
Note:
!
CAUTION:
The files defined by HTTP server configuration must be accessible from all IP deskphones invoking those files. Ensure that the file names match the names in the upgrade script, including case, since UNIX systems are case-sensitive.
Note:
Use any HTTP application you want. Commonly used HTTP applications include
Apache
®
and Microsoft
®
IIS™.
Important:
!
Important:
You must use the Avaya Web configuration server to obtain HTTPS so information is authenticated.
The Avaya Web configuration server does not support backup/restore. If you intend to use HTTP for backup/restore purposes, you must use an HTTP server that is independent of the Avaya Web configuration server.
To set up an HTTP server:
● Install the HTTP server application.
● Administer the system parameter HTTPSRVR to the address(es) of the HTTP server. Include these parameters in DHCP Option 242, or the appropriate SSON Option.
Issue 5 May 2014 49
Server Administration
● Download the upgrade script file and application file(s) from the Avaya Web site http://www.avaya.com/support to the HTTP server. For more information, see
Contents of the Settings File on page 58.
Note:
Note:
Many LINUX servers distinguish between upper and lower case names. Ensure that you specify the settings file name accurately, as well as the names and values of the data within the file.
If you choose to enhance the security of your HTTP environment by using Transport Layer Security
(TLS), you also need to:
● Install the TLS server application.
● Administer the system parameter TLSSRVR to the address(es) of the Avaya HTTPS server.
HTTP Configuration for Backup/Restore
For IIS Web Servers
For IIS 4.0 (WinNT4.0), IIS 5.0 (Win2000), IIS 5.1 (WinXP), IIS 6.0 (Win2003):
1. Create a “backup” folder under the root directory of your Web server. All backup files will be stored in that directory.
For example, if your backup folder is C:/Inetpub/wwwroot/backup the 46xxsettings.txt file should have a line similar to:
[SET BRURI http://www.website.com/backup/]
If your backup folder is the root directory, the 46xxsettings.txt file should have a line similar to:
[SET BRURI http://www.website.com/]
2. Use Internet Information Services Manager or Internet Information Services depending on your OS. Go to Start --> Settings --> Control Panel --> Administrative Tools.
3. Right click on the folder created for backup, or right click on Default Web Site if there is no specific backup directory.
4. Select Properties.
5. In the Directory tab, make sure the Write box is checked.
50 1600 Series IP Deskphone Administrator Guide Release 1.3.5
HTTP Configuration for Backup/Restore
Additional step for IIS 6.0 (Win2003):
1. Use Internet Information Services. Go to Start --> Settings --> Control Panel -->
Administrative Tools.
2. Below Default Web Site select Web Services Extension.
3. Make sure the WebDAV option is set to Allowed.
For Apache Web servers:
1. Create a “backup” folder under the root directory of your Web server, and make the folder
writable by everyone. All backup files will be stored in that directory.
If your backup folder is for instance C:/Program Files/Apache Group/Apache2/htdocs/backup, the 46xxsettings.txt file should have a line similar to:
[SET BRURI http://www.website.com/backup/]
If your backup folder is the root directory, the 46xxsettings.txt file should have a line similar to:
[SET BRURI http://www.website.com/]
2. Edit your Web server configuration file httpd.conf.
3. Uncomment the two LoadModule lines associated with DAV:
LoadModule dav_module modules/mod_dav.so
LoadModule dav_fs_module modules/mod_dav_fs.so
Note:
Note:
If these modules are not available on your system, typically the case on some Unix/Linux
Apache servers, you have to recompile these two modules (mod_dav & mod_dav_fs) into the server. Other ways to load these modules might be available. Check your
Apache documentation at http://httpd.apache.org/docs/ for more details.
4. Add the following lines in the httpd.conf file:
#
# WebDAV configuration
#
DavLockDB "C:/Program Files/Apache Group/Apache2/var/DAVLock"
<Location />
Dav On
</Location>
For Unix/Linux Web servers the fourth line might look more like:
DavLockDB/usr/local/apache2/var/DAVLock
5. Create the var directory and make it writable by everyone. Right click
Properties-->Security-->Add-->Everyone-->Full Control.
Issue 5 May 2014 51
Server Administration
Web Configuration Tool
Recent call server versions provide all the Web configuration support the 1600 Series IP Deskphones require. Also, the media server has an easy to use, PC-based interface for creating script files. Given
these resources, you do not need to manually create the text files discussed in 1600 Series IP
Deskphone Scripts and Application Files
. For more information about the media server, see Installation
and Upgrades for Avaya G700 Media Gateway and Avaya S8300 Media Server, available on the Avaya support Web site.
Table 9: 1600 Series IP Deskphone Customizable System Parameters lists the parameters you can
administer when manually creating the configuration file. Manual administration is discussed in 1600
Series IP Deskphone Scripts and Application Files
. When using the media server, you do not need to know the specific parameter names, since the media server handles that. For more information,
lists the parameter names from 1600 Series IP Deskphone Customizable System Parameters and the
corresponding field name from the media server HTTP server application. Any limits, restrictions, etc. about the parameters are built into the media server.
Note:
Note:
The Web Configuration application covers other IP deskphones in addition to the 1600
Series IP Deskphones. This document covers only data applicable to 1600 Series IP
Deskphones.
Table 7: Media Server Field Names & Corresponding Script File Parameter
Names
Media Server Field Name
Handset Audio Gain Control Status
Headset Audio Gain Control Status
Speaker Audio Gain Control Status
Application Status
Script File Server Authentication
Note: Applicable only when configuration file downloaded using HTTPS. Not applicable if file downloaded using HTTP.
Idle Time Before Backlight Turnoff
Backup and Restore URI
802.1X Supplicant Mode
Script File Parameter Name
AGCHAND
AGCHEAD
AGCSPKR
APPSTAT
AUTH
BAKLIGHTOFF
BRURI
DOT1X
DOT1XSTAT
1 of 3
52 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Web Configuration Tool
Table 7: Media Server Field Names & Corresponding Script File Parameter
Names (continued)
Media Server Field Name
DHCP Lease Violation Flag
Domain Name
Domain Name Server
HTTP Server IP Address
HTTP Directory
Send Destination Unreachable Messages
Process Received Redirect Messages
Layer 2 Frame Tagging
802.1A VLAN Identifier
System-Wide Language
English Language Selection Status
Language File Name
Font File Name
Event Log Security Level
Syslog Server Address
Management Complex IP Addresses
Voice Mail Deskphone Number
User Options Access
Deskphone Country Code
Deskphone Dial Plan Length
International Access Code
Long Distance Access Code
National Deskphone # Length
Outside Line Access Code
Ethernet Line Interface Status
Script File Parameter Name
DHCPSTD
DOMAIN
DNSSRVR
HTTPSRVR
HTTPDIR
ICMPDU
ICMPRED
L2Q
L2QVLAN
LANGSYS
LANG0STAT
LANGxFILE (with x being 1-4)
FONTFILE
LOGLOCAL
LOGSRVR
MCIPADD
MSGNUM
OPSTAT
PHNCC
PHNDPLENGTH
PHNIC
PHNLD
PHNLDLENGTH
PHNOL
PHY1STAT
2 of 3
Issue 5 May 2014 53
Server Administration
Table 7: Media Server Field Names & Corresponding Script File Parameter
Names (continued)
Media Server Field Name
Secondary Ethernet Interface Layer 2 Priority Value
Secondary Ethernet Line Interface Status
Secondary Ethernet Interface VLAN Identifier
Local (dial pad) Procedure Password
Local Dialpad Procedures Allowed
Reregistration Timer
RTCP Monitor IP Address
Source IP Addresses for SNMP Queries
SNMP Community String
Subscription List
Trusted Domains/Paths
Unnamed Registration Status
Secondary Ethernet Interface Layer 2 Frame Tagging
Wait Time for DHCP Offer
Script File Parameter Name
PHY2PRIO
PHY2STAT
PHY2VLAN
PROCPSWD
PROCSTAT
REREGISTER
RTCPMON
SNMPADD
SNMPSTRING
SUBSCRIBELIST
TPSLIST
UNNAMEDSTAT
VLANSEP
VLANTEST
3 of 3
54 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Chapter 6: Deskphone Software and Application
Files
General Download Process
The 1600 Series IP Deskphones download script files and settings files from either an HTTP or HTTPS server. These deskphones download the application files from the HTTP server. The HTTPS server applies only if the server supports Transport Layer Security (TLS) encryption.
Note:
Note:
The script files, application files, and settings files discussed in this chapter are identical for HTTP and HTTPS servers. The generic term “file server” refers to both “HTTP server” and “HTTPS server.”
The file downloading process is the same for both servers, except when you use an HTTPS server, a
TLS server is contacted first. The deskphone queries the file server, which transmits a script file to the deskphone. The script file tells the deskphone which application file the deskphone must use. The application file is the software that has the telephony functionality, and is easily updated for future enhancements. In a newly installed deskphone, the application file might be missing. In a previously installed deskphone, the application file might not be the proper one. In both cases, the deskphone requests a download of the proper application file from the HTTP server. The file server downloads the file and conducts some checks to ensure that the file was downloaded properly. If the deskphone determines it already has the proper file, the deskphone proceeds to the next step without downloading the application file again.
After checking and loading the application file, the 1600 Series IP Deskphone, if appropriate, uses the script file to look for a settings file. The settings file contains options you have administered for any or all of the 1600 Series IP Deskphones in your network. For more information about the settings file, see
Contents of the Settings File on page 58.
Software
When shipped from the factory, the1600 Series IP Deskphones might not contain sufficient software for registration and operation. When the deskphone is first plugged in, a software download from an HTTP server starts to give the phone its proper functionality.
For software upgrade downloads, the call server provides the capability for a remote restart of the 1600
Series IP Deskphone. As a result of restarting, the deskphone automatically starts reboot procedures. If new software is available on the server, the deskphone downloads it as part of the reboot process. The
Avaya 1600 Series IP Deskphones Installation and Maintenance Guide covers upgrades to a previously installed deskphone and related information.
Issue 5 May 2014 55
Deskphone Software and Application Files
1600 Series IP Deskphone Scripts and Application Files
Choosing the Right Application File and Upgrade Script File
The software releases containing the files needed to operate the 1600 Series IP Deskphones are bundled together. You download this self-extracting executable file to your file server from the Avaya support Web site at: http://www.avaya.com/support . The file is available in both zipped and unzipped format.
The bundle contains:
● An upgrade script file and a settings file, which allow you to upgrade to new software releases and new functionality without having to replace IP deskphones.
● Application files for all current 1600 Series IP Deskphones.
● Other useful information such as a ReadMe file and a settings file template to customize parameters and settings, and the latest binary code.
● Font files
● Language files
Upgrade Script File
An upgrade script file tells the IP deskphone whether the deskphone needs to upgrade software. The
Avaya IP Deskphones attempt to read this file whenever they reset. The upgrade script file also points to the settings file.
You download a default upgrade script file, sometimes called the “script file,” from http://www.avaya.com/support . This file allows the deskphone to use default settings for customer-definable options. This file must reside in the same directory as the upgrade script file, and must be called 46xxsettings.txt. The settings file contains settings for 1600, 9600, and 4600 Series IP
Deskphones.
Note:
Note:
Avaya recommends that the settings file have the extension *.txt. The Avaya IP
Deskphones can operate without this file. You can also change these settings with
DHCP or, in some cases, from the dialpad of the deskphone.
56 1600 Series IP Deskphone Administrator Guide Release 1.3.5
1600 Series IP Deskphone Scripts and Application Files
Settings File
The settings file contains the option settings you need to customize the Avaya IP Deskphones for your enterprise.
Note:
Note:
You can use one settings file for all your Avaya IP Deskphones. The settings file includes the 1600 Series IP Deskphones covered in this document as well as 9600 Series IP
Deskphones and 4600 Series IP Deskphones.
The settings file can include any of five types of statements, one per line:
●
●
●
●
●
Comments, which are statements with a “#” character in the first column.
Tags, which are comments that have exactly one space character after the initial #, followed by a text string with no spaces.
Goto commands, of the form GOTO tag. Goto commands cause the deskphone to continue interpreting the configuration file at the next line after a # tag statement. If no such statement exists, the rest of the configuration file is ignored.
Conditionals, of the form IF $name SEQ string GOTO tag. Conditionals cause the Goto command to be processed if the value of name is a case-insensitive equivalent to string. If no such name exists, the entire conditional is ignored. The only system values that can be used in a conditional statement are: BOOTNAME, GROUP, and SIG.
SET commands, of the form SET parameter_name value. Invalid values cause the specified value to be ignored for the associated parameter_name so the default or previously administered value is retained. All values must be text strings, even if the value itself is numeric, a dotted decimal IP address, and so on.
Note:
Note:
Enclose all data in quotation marks for proper interpretation.
The upgrade script file Avaya provides includes a line that tell the deskphone to GET 46xxsettings.txt.
This lines causes the deskphone to use HTTP or HTTPS to attempt to download the file specified in the
GET command. If the file is obtained, its contents are interpreted as an additional script file. That is how your settings are changed from the default settings. If the file cannot be obtained, the deskphone continues processing the upgrade script file.
If the configuration file is successfully obtained but does not include any setting changes the deskphone stops using HTTP. This happens when you initially download the script file template from the Avaya support Web site, before you make any changes. When the configuration file contains no setting changes, the deskphone does not go back to the upgrade script file.
Avaya recommends that you do not alter the upgrade script file. If Avaya changes the upgrade script file in the future, any changes you have made will be lost. Avaya recommends that you use the
46xxsettings file to customize your settings instead. However, you can change the settings file name, if desired, as long as you also edit the corresponding GET command in the upgrade script file.
For more information on customizing your settings file, see Contents of the Settings File
.
Issue 5 May 2014 57
Deskphone Software and Application Files
Contents of the Settings File
After checking the application software, the 1600 Series IP Deskphone looks for a 46xxsettings file.
This optional file is where you identify non-default option settings, application-specific parameters, and so on. You can download a template for this file from the Avaya support Web site. An example of what the file might look like follows.
Note:
Note:
The following is intended only as a simple example. Your settings will vary from the settings shown. This sample assumes specification of a DNS Server and turning off enhanced local dialing for 96xx Series IP Deskphones.
DNSSRVR=”dnsexample.yourco.com”
ENDIALSTAT=0
See Chapter 7: Administering Deskphone Options
for details about specific values. You need only specify settings that vary from defaults, although specifying defaults is harmless.
VLAN separation controls whether or not traffic received on the secondary Ethernet interface are forwarded on the voice VLAN and whether network traffic received on the data VLAN are forwarded to the deskphone. Add commands to the 46xxsettings.txt file to enable VLAN separation. The following example assumes the voice VLAN ID is “xxx”, the data VLAN ID is “yyy” and the data traffic priority is
“z”:
SET VLANSEP 1
SET L2Q 1 (or 0 for auto)
SET L2QVLAN xxx
SET PHY2VLAN yyy
SET PHY2PRIO z
Note:
Note:
Also configure the network switch so that 802.1Q tags are not removed from frames forwarded to the deskphone.
58 1600 Series IP Deskphone Administrator Guide Release 1.3.5
The GROUP System Value
The GROUP System Value
You might have different communities of users, all of which have the same deskphone model, but which require different administered settings. For example, you might want to restrict Call Center agents from being able to Logoff, which might be an essential capability for “hot-desking” associates. We provide examples of the group settings for each of these situations later in this section.
Use the GROUP system value for this purpose:
1. identify which deskphones are associated with which group, and designate a number for each group. The number can be any integer from 0 to 999, with 0 as the default, meaning your largest group is assigned as Group 0.
2. At each non-default deskphone, instruct the installer or user to invoke the GROUP Local (dialpad)
Administrative procedure as specified in the Avaya 1600 Series IP Deskphones Installation and
Maintenance Guide and specify which GROUP number to use. The GROUP System value can only be set on a phone-by-phone basis.
3. Once the GROUP assignments are in place, edit the configuration file to allow each deskphone of the appropriate group to download its proper settings.
Here is an example of the configuration file for the Call Center agent:
IF $GROUP SEQ 1 goto CALLCENTER
IF $GROUP SEQ 2 goto HOTDESK
{specify settings unique to Group 0} goto END
# CALLCENTER
{specify settings unique to Group 1} goto END
# HOTDESK
{specify settings unique to Group 2}
# END
{specify settings common to all Groups}
Call Center Administration
With Release 1.3.3, you can control the operations of the following buttons in a call center environment by setting the appropriate values in the settings file.
Issue 5 May 2014 59
Deskphone Software and Application Files
● HOLD
● CONFERENCE
● DROP
● MUTE
● HEADSET
● SWITCH HOOK
● TRANSFER
60 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Call Center Administration
Table 8: Call Center administration parameters
Parameter name
CCBTNSTAT 1
Default value
Valid values
HEADSTAT
HOLDSTAT
HOOKSTAT
MUTESTAT
XFERSTAT
0
0
0
0
0
Usage
1 ASCII numeric digit; 0 and 1
1 ASCII numeric digit; 0 and 1
1 ASCII numeric digit; 0 and 1
1 ASCII numeric digit; 0 and 1
1 ASCII numeric digit 0 and 1
1 ASCII numeric digit 0 and 1
Call Center permission flag;
1 = all buttons have normal operation;
0 = Conference, Drop, Headset, Hold,
Mute, and Transfer buttons, and the switchhook are disabled unless you individually configure the values as indicated in the following rows.
Headset button permission flag;
1 = normal operation;
0 = normal operation unless
CCBTNSTAT = 0, in which case the
Headset button is disabled.
Hold button permission flag;
1 = normal operation;
0 = normal operation unless
CCBTNSTAT = 0, in which case the
Hold button is disabled.
Switchhook permission flag;
1 = normal operation;
0 = normal operation unless
CCBTNSTAT = 0, in which case the switchhook is disabled.
Mute button permission flag;
1 = normal operation;
0 = normal operation unless
CCBTNSTAT = 0, in which case the
Mute button is disabled.
Transfer button permission flag;
1 = normal operation;
0 = normal operation unless
CCBTNSTAT = 0, in which case the
Transfer button is disabled.
Issue 5 May 2014 61
Deskphone Software and Application Files
Table 8: Call Center administration parameters
Parameter name
CONFSTAT
DROPSTAT
HEADSTAT
HOLDSTAT
HOOKSTAT
MUTESTAT
XFERSTAT
Default value
0
0
0
0
0
0
0
Valid values Usage
1 ASCII numeric digit; 0 and 1
1 ASCII numeric digit; 0 and 1
1 ASCII numeric digit; 0 and 1
1 ASCII numeric digit; 0 and 1
1 ASCII numeric digit; 0 and 1
1 ASCII numeric digit 0 and 1
1 ASCII numeric digit 0 and 1
Conference button permission flag;
1 = normal operation;
0 = normal operation unless
CCBTNSTAT = 0, in which case the
Conference button is disabled.
Drop button permission flag;
1 = normal operation;
0 = normal operation unless
CCBTNSTAT = 0, in which case the
Drop button is disabled.
Headset button permission flag;
1 = normal operation;
0 = normal operation unless
CCBTNSTAT = 0, in which case the
Headset button is disabled.
Hold button permission flag;
1 = normal operation;
0 = normal operation unless
CCBTNSTAT = 0, in which case the
Hold button is disabled.
Switchhook permission flag;
1 = normal operation;
0 = normal operation unless
CCBTNSTAT = 0, in which case the switchhook is disabled.
Mute button permission flag;
1 = normal operation;
0 = normal operation unless
CCBTNSTAT = 0, in which case the
Mute button is disabled.
Transfer button permission flag;
1 = normal operation;
0 = normal operation unless
CCBTNSTAT = 0, in which case the
Transfer button is disabled.
!
Important:
Example
Important:
You can access the local procedures only if you have enabled the Mute button.
62 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Call Center Administration
If you want to disable all the buttons, except the switchhook so that the switchhook functions normally, set CCBTNSTAT to 0 so that by default, all the applicable buttons are disabled and set HOOKSTAT=1 to enable the switchhook button.
Issue 5 May 2014 63
Deskphone Software and Application Files
64 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Chapter 7: Administering Deskphone Options
Administering Options for the 1600 Series IP Deskphones
This chapter explains how to change parameters by means of the DHCP or HTTP servers. In all cases, you are setting a system parameter in the deskphone to a desired value.
lists:
● the parameter names,
● their default values,
● the valid ranges for those values, and
● a description of each one.
For DHCP, the DHCP Option sets these parameters to the desired values as discussed in
File Servers on page 37. For HTTP, the parameters in
Table 9 are set to desired values in the script file.
For more information, see Contents of the Settings File on page 58. When using a media server, see
Table 7: Media Server Field Names & Corresponding Script File Parameter Names on page 52 for
information on parameters set by the media server application.
Avaya recommends that you administer options on the 1600 Series IP Deskphones using script files.
Some DHCP applications have limits on the amount of user-specified information. The administration required can exceed those limits for the more full-featured deskphone models.
You might choose to completely disable the capability to enter or change option settings from the dialpad. You can set the system value, PROCPSWD, as part of standard DHCP/HTTP administration.
Alternately, you can set PROCPSWD on the system-parameters ip-options form, as of Avaya Aura
Communication Manager Release 5.2.
For more information on dialpad options, see the Avaya 1600 Series IP Deskphones Installation and
Maintenance Guide.
CAUTION:
!
CAUTION:
PROCPSWD is likely stored on the server in clear text and is sent to the deskphone in the unencrypted. Therefore, do not consider PROCPSWD as a high-security technique to inhibit a sophisticated user from obtaining access to local procedures.
Administering this password can limit access to all local procedures, including
V I E W. VIEW is a read-only option that allows review of the current deskphone settings.
Table 9: 1600 Series IP Deskphone Customizable System Parameters
Parameter Name
AGCHAND
Default Value
1
Description and Value Range
Automatic Gain Control status for handset
(0=disabled, 1=enabled).
1 of 7
Issue 5 May 2014 65
Administering Deskphone Options
Table 9: 1600 Series IP Deskphone Customizable System Parameters (continued)
Parameter Name
AGCHEAD
AGCSPKR
APPNAME
APPSTAT
AUTH
BAKLIGHTOFF
BRURI
DHCPSTD
DNSSRVR
DOMAIN
DOT1X
Default Value
1
1
" " (Null)
1
0
120
" " (Null)
0
0.0.0.0
" " (Null)
0
Description and Value Range
Automatic Gain Control status for headset
(0=disabled, 1=enabled).
Automatic Gain Control status for Speaker
(0=disabled, 1=enabled).
Primary application image file name, as provided in the
1600upgrade.txt file.
Controls whether specific applications are enabled, restricted, or disabled. Values are: 1=all applications enabled, 2=Speed Dial (Contacts) changes and Call
Log disabled and Redial last number only, 3=Speed
Dial (Contacts) changes disabled, 0=Speed Dial
(Contacts) changes, Call Log, and Redial disabled.
Script file authentication value (0=HTTP is acceptable,
1=HTTPS is required).
Number of minutes without display activity to wait before turning off the backlight. Values: 0-999, no spaces and no null value. A value of 0 means the backlight never turns off.
URL used for backup and retrieval of user data. Specify
HTTP server and directory path to backup file. Do not specify backup file name. Value: 0-255 ASCII characters. Null is a valid value and spaces are allowed.
DHCP Standard lease violation flag. Indicates whether to keep the IP address if there is no response to lease renewal. If set to “1” (No) the deskphone strictly follows the DHCP standard with respect to giving up IP addresses when the DHCP lease expires. If set to “0”
(Yes) the deskphone continues using the IP address until it detects reset or a conflict (see
).
Text string containing the IP address of zero or more
DNS servers, in dotted-decimal format, separated by commas with no intervening spaces (0-255 ASCII characters, including commas).
Text string containing the domain name to be used when DNS names in system values are resolved into
IP addresses. Valid values are 0-255 ASCII characters.
If Null, no spaces allowed.
802.1X Supplicant operation mode. Valid values are:
0=With PAE pass-through, 1=with PAE pass-through and proxy Logoff, 2=without PAE pass-through or proxy Logoff. For more information, see
2 of 7
66 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Administering Options for the 1600 Series IP Deskphones
Table 9: 1600 Series IP Deskphone Customizable System Parameters (continued)
Parameter Name
DOT1XSTAT
ENHDIALSTAT
FONTFILE
HTTPDIR
HTTPSRVR
ICMPDU
ICMPRED
L2Q
L2QVLAN
LANG0STAT
LANGxFILE
Default Value
0
1
" " (Null)
" " (Null)
" " (Null)
0
0
0
0
1
" " (Null)
Description and Value Range
Determines how the deskphone handles Supplicants.
Valid values are:
0=Supplicant operation is completely disabled.
1=Supplicant operation is enabled, but responds only to received unicast EAPOL messages.
2=Supplication operation is enabled and responds to received unicast and multicast EAPOL messages. For
more information, see IEEE 802.1X
Enhanced Dialing Status. If set to “1” the
Local Dialing feature is turned on for all associated
applications. If set to “0” the feature is turned off.
Name of the font file for a language for a 1600 Series
International deskphone.
HTTP server directory path. The path name prepended to all file names used in HTTP and HTTPS get operations during initialization. Value: 0-127 ASCII characters, no spaces. Null is a valid value. Leading or trailing slashes are not required.
Text list of HTTP server addresses in dotted decimal or
DNS format, separated by commas (0-255 ASCII characters, including commas).
Controls whether ICMP Destination Unreachable messages will be processed. Values are: 0=No,
1=Send limited Port Unreachable messages, 2=Send
Protocol and Port Unreachable messages.
Controls whether ICMP Redirect messages will be processed. Values are: 0=No, 1=Yes.
Controls whether Layer 2 frames have IEEE 802.1Q tags (0=auto, 1=enabled, 2=disabled).
802.1Q VLAN Identifier (0 to 4094). Null (" ") is not a valid value and the value cannot contain spaces. VLAN identifier used by IP deskphones. Set this parameter only when IP deskphones are to use a VLAN that is separate from the default data VLAN. If the VLAN identifier is to be configured via H.323 signaling based on Avaya Aura Communication Manager administration forms, it should not be set here.
Controls whether the built-in English language text strings can be selected by the user. Valid values are:
0 = User cannot select English language text strings
1 = User can select English language text strings/
Name of the language file in use:
LANG1FILE =
LANG2FILE =
LANG3FILE =
LANG4FILE =
3 of 7
Issue 5 May 2014 67
Administering Deskphone Options
Table 9: 1600 Series IP Deskphone Customizable System Parameters (continued)
Parameter Name
LANGSYS
LOGLOCAL
LOGSRVR
MCIPADD
MSGNUM
OPSTAT
Default Value
" " (Null)
0
" " (Null)
0.0.0.0
" " (Null)
111
Description and Value Range
0 to 32 ASCII characters. The file name of the system default language file, if any.
Event Log Severity Level (one 0-8 ASCII numeric digit). Controls the level of events logged in the endptRecentLog and endptResetLog objects in the
SNMP MIB. Events with the selected level and with a higher severity level will be logged. Valid values are:
0=Disabled, 1=emergencies, 2=alerts, 3=critical,
4=errors, 5=warnings, 6=notices, 7=information,
8=debug.
Voice Monitoring Manager (VMM) Server Address.
Zero or one IP address in dotted-decimal format or
DNS Name format (0-15 ASCII characters).
Call Server Address. Zero or more Avaya Aura
Communication Manager server IP addresses. Format is dotted-decimal or DNS name format, separated by commas without intervening spaces (0-255 ASCII characters, including commas). Null is a valid value.
Voice mail deskphone number. Specifies the number to be dialed automatically when the deskphone user presses the Message button. Value: 0-30 ASCII dialable characters (0-9, * and #) and no spaces. Null is a valid value.
Options status flag(s) (1 or 3 ASCII numeric digits) indicate which options are user-selectable. The default of 111 grants access to all options and related applications.
Single digit valid values are:
1=user can access all options, including Logout,
2= user can access only view-oriented applications.
PHNCC 1
Three-digit valid values are a concatenation of binary values, in the form abc, where each letter represents a
0 (disabled/off) or 1 (enabled/on), interpreted as:
a = base settings for all user options and related applications, except as noted in b or c.
b = setting for view-oriented applications (for example, the Network Information application), as applicable.
c = setting for Logout application, if applicable.
The binary "0" does not allow an end user to see or invoke options and related applications. The binary "1" allows full display and access to all options and related applications.
Deskphone country code. The administered international country code for the location by the algorithm that dials calls from the incoming Call Log or from Web pages. Range: 1-3 digits, from “1” to “999.”
4 of 7
68 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Administering Options for the 1600 Series IP Deskphones
Table 9: 1600 Series IP Deskphone Customizable System Parameters (continued)
Parameter Name
PHNDPLENGTH
PHNIC
PHNLD
PHNLDLENGTH
PHNOL
PHY1STAT
PHY2PRIO
PHY2STAT
Default Value
5
011
1
10
9
1
0
1
Description and Value Range
Internal extension deskphone number length. Specifies the number of digits associated with internal extension numbers by the algorithm that dials calls from the incoming Call Log or from Web pages. Range: 1 or 2 digits, from “3” to “10.”
Deskphone international access code. The maximum number of digits, if any, dialed to access public network international trunks by the algorithm that dials calls from the incoming Call Log or from Web pages. Range:
0-4 digits.
Deskphone long distance access code. The digit, if any, dialed to access public network long distance trunks by the algorithm that dials calls from the incoming Call Log or from Web pages. Range: 1 digit or " " (Null).
Length of national deskphone number. The number of digits in the longest possible national deskphone number by the algorithm that dials calls from the incoming Call Log or from Web pages. Range: 1 or 2 digits, from “3” to “10.” Range: 1 or 2 ASCII numeric characters, from “5” to “15.”
Outside line access code. The character(s) dialed, including # and *, if any, to access public network local trunks by the algorithm that dials calls from the incoming Call Log or from Web pages. Range: 0-2 dialable characters, including " " (Null).
Ethernet line interface setting (1=auto-negotiate,
2=10Mbps half-duplex, 3=10Mbps full-duplex,
4=100Mbps half-duplex, 5=100Mbps full-duplex, and
6=1000Mbps full-duplex if supported by the hardware).
Layer 2 priority value for frames received on or forwarded to the secondary Ethernet interface. Set this parameter only when VLAN separation is "1"
(enabled). Values are from 0-7 and correspond to the drop-down menu selection.
Secondary Ethernet interface setting
(0=Secondary Ethernet interface off/disabled,
1=auto-negotiate, 2=10Mbps half-duplex, 3=10Mbps full-duplex, 4=100Mbps half-duplex, 5=100Mbps full-duplex), and 6=1000Mbps full-duplex if supported by the hardware).
5 of 7
Issue 5 May 2014 69
Administering Deskphone Options
Table 9: 1600 Series IP Deskphone Customizable System Parameters (continued)
Parameter Name
PHY2VLAN
PROCPSWD
Default Value
0
27238
Description and Value Range
VLAN identifier used by frames received on or forwarded to the secondary Ethernet interface. Set this parameter only when VLAN separation is "1"
(enabled). Value is 1-4 ASCII numeric digits from “0” to
“4094.” Null is not a valid value, nor can the value contain spaces. If this value is set by LLDP using the
Port VLAN ID TLV value, it will not change regardless of settings from other sources. For more information,
see Parameter Data Precedence .
Text string containing the local dialpad procedure password. The string can have a value of 4 to 7 ASCII digits from 0000 to 9999999. If set, you must enter the password immediately after you press the Mute button and before you enter the procedure command, for example, the VIEW command. The password is
Intended to facilitate restricted access to local procedures even when command sequences are known. Password is viewable, not hidden.
PROCSTAT
REREGISTER
RTCPMON
SNMPADD
SNMPSTRING
0
20
" " (Null)
" " (Null)
" " (Null)
Note:
Note:
After you upgrade the deskphone to
Release 1.3.3, a default value of 27238 is assigned to PROCPSWD if you have not previously changed the value of
PROCPSWD.
Local (dialpad) Administrative procedures status
(0=Local procedures enabled, 1=all Administrative
Options are disabled).
Registration timer in minutes. Controls an H.323 protocol timer that should only be changed under very special circumstances by someone who fully understands the system operation impact. Value is
1-120.
Text string containing the 4-octet IP address of the
RTCP monitor currently in use, in dotted decimal or
DNS Name format (0-15 ASCII characters, no spaces).
Text string containing zero or more allowable source IP addresses for SNMP queries, in dotted decimal or DNS format, separated by commas, with up to 255 total
ASCII characters including commas.
Text string containing the SNMP community name string (up to 32 ASCII characters, no spaces).
6 of 7
70 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Administering Options for the 1600 Series IP Deskphones
Table 9: 1600 Series IP Deskphone Customizable System Parameters (continued)
Parameter Name
STATIC
SUBSCRIBELIST
TPSLIST
UNNAMEDSTAT
VLANSEP
VLANTEST
Default Value
0
" " (Null)
" " (Null)
1
1
60
Description and Value Range
Static programming override flag. If set to “0” static programming never overrides call server (DHCP) or call server administered data. If set to “1” static programming overrides only file server administered data. If set to “2” static programming overrides only call server administered data. If set to “3” static programming overrides both file server- and call server-administered data. Allows a call server IP address that has been manually programmed into a deskphone to override any value received via DHCP or via this configuration file. A manually programmed IP address will only be used if it is not 0.0.0.0, so this parameter may be used to allow only specific deskphones to use a different value than otherwise provided by this configuration file. If STATIC is to be used to select a manual override of file server IP address(es), STATIC must be set via DHCP, not via this configuration file.
One or more Push application server subscription
URLs, separated by commas without any intervening spaces (0-255 ASCII characters, including commas).
One or more trusted domain/path strings, separated by commas without any intervening spaces (0-255 ASCII characters, including commas). A URL pushed to a deskphone must contain one of these strings if it is to be used to obtain content to be rendered by the deskphone.
Unnamed Registration Status. Specifies whether unnamed registration is initiated if the user fails to enter a value at the Extension: prompt or Login screen.
Unnamed registration provides the deskphone with a
TTI-level service, enabling a user, for example, to dial emergency services like 911. Value 1=Yes, 0=No.
VLAN separation. Controls whether frames to/from the secondary Ethernet interface receive IEEE 802.1Q tagging treatment. The tagging treatment enables frames to be forwarded based on their tags in a manner separate from deskphone frames. If tags are not changed, no tag-based forwarding is employed.
Values are: 1=On/Enabled, 0= Off/Disabled. This parameter is used with several related parameters. For
more information, see VLAN Separation on page 73.
Number of seconds to wait for a DHCPOFFER when using a non-zero VLAN ID (1-3 ASCII digits, from “0” to
“999”).
7 of 7
Issue 5 May 2014 71
Administering Deskphone Options
Note:
Note:
Table 9 applies to all 1600 Series IP Deskphones. Certain 1600 IP Deskphones might
have additional, optional information that you can administer. For more information, see
Chapter 8: Administering Applications and Options .
VLAN Considerations
If your LAN environment does not include Virtual LANs (VLANs), ignore this section. Otherwise, this section contains information on how to administer 1600 Series IP Deskphones to minimize registration time and maximize performance in a VLAN environment.
VLAN Tagging
IEEE 802.1Q tagging (VLAN) is a useful method of managing VoIP traffic in your LAN. Avaya recommends that you establish a voice LAN, set L2QVLAN to that VLAN, and provide voice traffic with priority over other traffic. If LLDP was used to set the deskphones’ VLAN, that setting has absolute authority. Otherwise, you can set VLAN tagging manually, by DHCP, or in the 46xxsettings.txt file.
If VLAN tagging is enabled (L2Q=0 or 1), the 1600 Series IP Deskphones set the VLAN ID to
L2QVLAN, and VLAN priority for packets from the deskphone to L2QAUD for audio packets and
L2QSIG for signalling packets. The default value (6) for these parameters is the recommended value for voice traffic in IEEE 802.1D.
Regardless of the tagging setting, a 1600 Series IP Deskphone will always transmit packets from the deskphone at absolute priority over packets from secondary Ethernet. The priority settings are useful only if the downstream equipment is administered to give the voice LAN priority.
VLAN Default Value and Priority Tagging
The system value L2QVLAN is initially set to “0” and identifies the 802.1Q VLAN Identifier. This default value indicates “priority tagging” as defined in IEEE 802.IQ Section 9.3.2.3. Priority tagging specifies that your network closet Ethernet switch automatically insert the switch port default VLAN without changing the user priority of the frame (cf. IEEE 802.1P and 802.1Q).
If you do not want the default VLAN to be used for voice traffic:
● Ensure that the switch configuration lets frames tagged by the 1600 Series IP Deskphone through without overwriting or removing them.
● Set the system value L2QVLAN to the VLAN ID appropriate for your voice LAN.
72 1600 Series IP Deskphone Administrator Guide Release 1.3.5
VLAN Considerations
Another system value you can administer is VLANTEST. VLANTEST defines the number of seconds the 1600 IP Series Deskphone waits for a DHCPOFFER message when using a non-zero VLAN ID.
The VLANTEST default is “60” seconds. Using VLANTEST ensures that the deskphone returns to the default VLAN if an invalid VLAN ID is administered or if the phone moves to a port where the L2QVLAN value is invalid. The default value is long, allowing for the scenario that a major power interruption is causing the phones to restart. Always allow time for network routers, the DHCP servers, etc. to be returned to service. If the deskphone restarts for any reason and the VLANTEST time limit expires, the deskphone assumes the administered VLAN ID is invalid. The deskphone then initiates registration with the default VLAN ID.
Setting VLANTEST to “0” has the special meaning of telling the phone to use a non-zero VLAN indefinitely to attempt DHCP. In other words, the deskphone does not return to the default VLAN.
Note:
Note:
If the deskphone returns to the default VLAN but must be put back on the L2QVLAN
VLAN ID, you must Reset the deskphone. See the Reset procedure in the Avaya 1600
Series IP Deskphones Installation and Maintenance Guide.
VLAN Separation
VLAN separation controls whether or not traffic received on the secondary Ethernet interface can be forwarded on the voice VLAN. VLAN separation also controls whether network traffic received on the data VLAN can be forwarded to the deskphone. The following system parameters control VLAN separation:
● VLANSEP - enables (1) or disables (0) VLAN separation. The default is 1 (on), which allows full separation. When set to 0 (off), VLAN IDs are not used as a criteria for forwarding frames.
● L2Q - 802.1Q tagging must be set to 1 (on) or 0 (auto).
● L2QVLAN - must be set to the non-zero VLAN ID of the voice VLAN.
● PHY2VLAN - must be set to the non-zero VLAN ID of the data VLAN, which cannot be the same as the voice VLAN ID.
● PHY2PRIO - the layer 2 priority value to be used for tagged frames received on the secondary
Ethernet interface.
provides several VLAN separation guidelines.
Issue 5 May 2014 73
Administering Deskphone Options
Table 10: VLAN Separation Rules
If Then
VLANSEP is “0”
(Off/Disabled),
OR the deskphone is tagging frames with a
VLAN ID equal to
PHY2VLAN.
VLANSEP is “1” (On/Enabled)
VLANSEP is “1”
(On/Enabled)
OR the deskphone is not tagging frames,
AND the deskphone is not tagging frames,
OR if the deskphone is tagging frames with a
VLAN ID equal to
PHY2VLAN,
Frames received on the secondary Ethernet interface will not be changed before forwarding. For example, tagging is not added or removed and the VLAN ID and tagged frames priority are not changed. The Ethernet switch forwarding logic determines that frames received on the Ethernet line interface are forwarded to the secondary Ethernet interface or to the deskphone without regard to specific
VLAN IDs or the existence of tags.
All tagged frames received on the secondary
Ethernet interface are changed before forwarding to make the VLAN ID equal to the
PHY2VLAN value and the priority value equal to the PHY2PRIO value.
Untagged frames received on the secondary
Ethernet interface are not changed before forwarding.
The Ethernet switch forwarding logic determines that frames received on the
Ethernet line interface are forwarded to the secondary Ethernet interface or to the deskphone without regard to specific VLAN
IDs or the existence of tags.
VLANSEP is “1”
(On/Enabled)
OR if the PHY2VLAN value is zero.
AND the deskphone is tagging frames with a
VLAN ID not equal to
PHY2VLAN,
AND the PHY2VLAN value is not zero.
Tagged frames received on the Ethernet line interface will only be forwarded to the secondary Ethernet interface if the VLAN ID equals PHY2VLAN.
Tagged frames received on the Ethernet line interface will only be forwarded to the deskphone if the VLAN ID equals the VLAN ID used by the deskphone.
Untagged frames will continue to be forwarded or not forwarded as determined by the
Ethernet switch forwarding logic.
74 1600 Series IP Deskphone Administrator Guide Release 1.3.5
DNS Addressing
DNS Addressing
The 1600 IP Deskphones support DNS addresses and dotted decimal addresses. The deskphone attempts to resolve a non-ASCII-encoded dotted decimal IP address by checking the contents of DHCP
Option 6. See DHCP Generic Setup on page 38 for information. At least one address in Option 6 must
be a valid, non-zero, dotted decimal address, otherwise, DNS fails. The text string for the DOMAIN
system parameter (Option 15, Table 9
) is appended to the address(es) in Option 6 before the deskphone attempts DNS address resolution. If Option 6 contains a list of DNS addresses, those addresses are queried in the order given if no response is received from previous addresses on the list.
As an alternative to administering DNS by DHCP, you can specify the DNS server and/or Domain name in the HTTP script file. But first SET the DNSSRVR and DOMAIN values so you can use those names later in the script.
Note:
Note:
Administer Options 6 and 15 appropriately with DNS servers and Domain names respectively.
IEEE 802.1X
Certain 1600 Series IP Deskphones support the IEEE 802.1X standard for pass-through and
Supplicant operation. The system parameter
determines how the deskphones handle 802.1X multicast packets and proxy logoff, as follows:
● When DOT1X = 0, the deskphone forwards 802.1X multicast packets from the Authenticator to the
PC attached to the deskphone and forwards multicast packets from the attached PC to the
Authenticator (multicast pass-through). Proxy Logoff is not supported.
● When DOT1X = 1, the deskphone supports the same multicast pass-through as when DOT1X=0.
Proxy Logoff is supported.
● When DOT1X = 2, the deskphone forwards multicast packets from the Authenticator only to the deskphone, ignoring multicast packets from the attached PC (no multicast pass-through). Proxy
Logoff is not supported.
● Regardless of the DOT1X setting, the deskphone always properly directs unicast packets from the
Authenticator to the deskphone or its attached PC, as dictated by the MAC address in the packet.
All 1600 Series deskphones support Supplicant operation and parameter values as specified in IEEE
802.1X, but, as of software Release 1.2, only if the value of the parameter DOT1XSTAT is "1" or "2". If
DOT1XSTAT has any other value, Supplicant operation is not supported.
IP deskphones will respond to unicast EAPOL frames (frames with the deskphone’s MAC address as the destination MAC address, and a protocol type of 88-8E hex) received on the Ethernet line interface if the value of DOT1XSTAT is "1" or "2", but will only respond to EAPOL frames that have the PAE group multicast address as the destination MAC address if the value of DOT1XSTAT is "2". If the value
Issue 5 May 2014 75
Administering Deskphone Options of DOT1XSTAT is changed to "0" from any other value after the Supplicant has been authenticated, an
EAPOL-Logoff will be transmitted before the Supplicant is disabled.
As of software Release 1.2, the system parameter DOT1XSTAT determines how the deskphone handles Supplicants as follows:
● When DOT1XSTAT=0, Supplicant operation is completely disabled. This is the default value.
● When DOT1XSTAT=1, Supplicant operation is enabled, but responds only to received unicast
EAPOL messages.
● When DOT1XSTAT=2, Supplicant operation is enabled and responds to received unicast and multicast EAPOL messages.
Note:
Note:
If the Ethernet line interface link fails, the 802.1X Supplicant, if enabled, enters the
Disconnected state. The 802.1X Supplicant variable userLogoff normally has a value of
FALSE. This variable will be set to TRUE before the deskphone drops the link on the
Ethernet line interface (and back to FALSE after the link has been restored). The userLogoff variable may also be briefly set to TRUE to force the Supplicant into the
LOGOFF state when new credentials are entered.
802.1X Pass-Through and Proxy Logoff
1600 Series IP Deskphones with a secondary Ethernet interface support pass-through of 802.1X packets to and from an attached PC. This enables an attached PC running 802.1X supplicant software to be authenticated by an Ethernet data switch.
The IP Deskphones support two pass-through modes:
● pass-through and
● pass-through with proxy logoff.
The DOT1X parameter setting controls the pass-through mode. In Proxy Logoff mode (DOT1X=1), when the secondary Ethernet interface loses link integrity, the deskphone sends an 802.1X
EAPOL-Logoff message to the data switch on behalf of the attached PC. The message alerts the switch that the device is no longer present. For example, a message would be sent when the attached
PC is physically disconnected from the IP deskphone. When DOT1X = 0 or 2, the Proxy Logoff function is not supported
802.1X Supplicant Operation
1600 IP Deskphones that support Supplicant operation also support Extensible Authentication Protocol
(EAP), but only with the MD5-Challenge authentication method as specified in IETF RFC 3748
[8.5-33a].
76 1600 Series IP Deskphone Administrator Guide Release 1.3.5
IEEE 802.1X
A Supplicant identity (ID) and password of no more than 12 numeric characters are stored in reprogrammable non-volatile memory. The ID and password are not overwritten by deskphone software downloads. The default ID is the MAC address of the deskphone, converted to ASCII format without colon separators, and the default password is null. Both the ID and password are set to defaults at manufacture. EAP-Response/Identity frames use the ID in the Type-Data field. EAP-Response/
MD5-Challenge frames use the password to compute the digest for the Value field, leaving the Name field blank.
When a deskphone is installed for the first time and 802.1x is in effect, the dynamic address process prompts the installer to enter the Supplicant identity and password. The IP deskphone does not accept null value passwords. See “Dynamic Addressing Process” in the Avaya 1600 Series IP Deskphones
Installation and Maintenance Guide. The IP deskphone stores 802.1X credentials when successful authentication is achieved. Post-installation authentication attempts occur using the stored 802.1X credentials, without prompting the user for ID and password entry.
An IP deskphone can support several different 802.1X authentication scenarios, depending on the capabilities of the Ethernet data switch to which it is connected. Some switches may authenticate only a single device per switch port. This is known as single-supplicant or port-based operation. These switches typically send multicast 802.1X packets to authenticating devices.
These switches support the following three scenarios:
● Standalone deskphone (Deskphone Only Authenticates) - When the IP deskphone is configured for Supplicant Mode (DOT1XSTAT=2), the deskphone can support authentication from the switch.
● Deskphone with attached PC (Deskphone Only Authenticates) - When the IP deskphone is configured for Supplicant Mode (DOT1X=2 and DOT1XSTAT=2), the deskphone can support authentication from the switch. The attached PC in this scenario gains access to the network without being authenticated.
● Deskphone with attached PC (PC Only Authenticates) - When the IP deskphone is configured for Pass-Through Mode or Pass-Through Mode with Logoff (DOT1X=0 or 1 and DOT1XSTAT=0), an attached PC running 802.1X supplicant software can be authenticated by the data switch. The deskphone in this scenario gains access to the network without being authenticated.
Some switches support authentication of multiple devices connected through a single switch port. This is known as multi-supplicant or MAC-based operation. These switches typically send unicast 802.1X packets to authenticating devices. These switches support the following two scenarios:
● Standalone deskphone (Deskphone Only Authenticates) - When the IP deskphone is configured for Supplicant Mode (DOT1XSTAT=2), the deskphone can support authentication from the switch. When DOT1X is "0" or "1", the deskphone is unable to authenticate with the switch.
● Deskphone and PC Dual Authentication - Both the IP deskphone and the connected PC can support 802.1X authentication from the switch. The IP deskphone may be configured for
Pass-Through Mode or Pass-Through Mode with Logoff (DOT1X=0 or 1 and DOT1XSTAT=1 or
2). The attached PC must be running 802.1X supplicant software.
Issue 5 May 2014 77
Administering Deskphone Options
Link Layer Discovery Protocol (LLDP)
Release 1.1 1600 Series IP Deskphones support IEEE 802.1AB. Link Layer Discovery Protocol (LLDP) is an open standards layer 2 protocol IP Deskphones use to advertise their identity and capabilities and to receive administration from an LLDP server. LAN equipment can use LLDP to manage power, administer VLANs, and provide some administration.
The transmission and reception of LLDP is specified in IEEE 802.1AB-2005. The 1600 Series IP
Deskphones use Type-Length-Value (TLV) elements specified in IEEE 802.1AB-2005, TIA TR-41
Committee - Media Endpoint Discovery (LLDP-MED, ANSI/TIA-1057), and Proprietary elements. LLDP
Data Units (LLDPDUs) are sent to the LLDP Multicast MAC address (01:80:c2:00:00:0e).
These deskphones:
●
● do not support LLDP on the secondary Ethernet interface.
will not forward frames received with the 802.1AB LLDP group multicast address as the destination MAC address between the Ethernet line interface and the secondary Ethernet interface.
A 1600 Series IP Deskphone initiates LLDP after receiving an LLDPDU message from an appropriate system. Once initiated, the deskphones send an LLDPDU every 30 seconds with the following contents:
Table 11: LLDPDU Transmitted by the 1600 Series IP Deskphones
Category
Basic Mandatory
Basic Mandatory
Basic Mandatory
Basic Optional
Basic Optional
TLV Name (Type)
Chassis ID
Port ID
Time-To-Live
System Name
System Capabilities
TLV Info String (Value)
IPv4 IP Address of deskphone.
MAC address of the deskphone.
120 seconds.
The Host Name sent to the DHCP server in
DHCP option 12.
Bit 2 (Bridge) will be set in the System
Capabilities if the deskphone has an internal
Ethernet switch. If Bit 2 is set in Enabled
Capabilities then the secondary port is enabled.
Bit 5 (Deskphone) will be set in the System
Capabilities. If Bit 5 is set in the Enabled
Capabilities than the deskphone is registered.
1 of 3
78 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Link Layer Discovery Protocol (LLDP)
Table 11: LLDPDU Transmitted by the 1600 Series IP Deskphones (continued)
Category
Basic Optional
TLV Name (Type) TLV Info String (Value)
Management Address Mgmt IPv4 IP Address of deskphone.
Interface number subtype = 3 (system port).
Interface number = 1.
IEEE 802.3
Organization
Specific
TIA LLDP MED
MAC / PHY
Configuration / Status
OID = SNMP MIB-II sysObjectID of the deskphone.
Reports autonegotiation status and speed of the uplink port on the deskphone.
TIA LLDP MED
TIA LLDP MED
TIA LLDP MED
TIA LLDP MED
TIA LLDP MED
TIA LLDP MED
TIA LLDP MED
TIA LLDP MED
Avaya Proprietary
Avaya Proprietary
LLDP-MED
Capabilities
Extended
Power-Via-MDI
Network Policy
Inventory – Hardware
Revision
Inventory – Firmware
Revision
Inventory – Software
Revision
Inventory – Serial
Number
Inventory –
Manufacturer Name
Inventory – Model
Name
PoE Conservation
Level Support
Media Endpoint Discovery - Class III - IP
Deskphone.
Power Value = 0 if the deskphone is not
currently powered via PoE, else the
maximum power usage of the deskphone plus
all modules and adjuncts powered by the
deskphone in tenths of a watt.
Tagging Yes/No, VLAN ID for voice, L2 Priority,
DSCP Value.
MODEL - Full Model Name.
BOOTNAME.
APPNAME.
Deskphone serial number.
Avaya.
MODEL with the final Dxxx characters removed.
Provides Power Conservation abilities/settings,
Typical and Maximum Power values.
Call Server IP
Address
OUI = 00-40-0D (hex), Subtype = 1.
Call Server IP Address.
Subtype = 3.
2 of 3
Issue 5 May 2014 79
Administering Deskphone Options
Table 11: LLDPDU Transmitted by the 1600 Series IP Deskphones (continued)
Category
Avaya Proprietary
TLV Name (Type) TLV Info String (Value)
IP Phone Addresses Phone IP Address, Phone Address Mask,
Gateway IP Address.
Avaya Proprietary
Avaya Proprietary
Basic Mandatory
File Server
802.1Q Framing
End-of-LLDPDU
Subtype = 4.
File Server IP Address.
Subtype = 6.
802.1Q Framing = 1 if tagging or 2 if not.
Subtype = 7.
Not applicable.
3 of 3
On receipt of a LLDPDU message, the Avaya IP Deskphones will act on the TLV elements described in
Table 12 :
80 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Link Layer Discovery Protocol (LLDP)
Table 12: Impact of TLVs Received by 1600 Series IP Deskphones on System Parameter
Values
System
Parameter Name
TLV
Name
PHY2VLAN
L2QVLAN and
L2Q
IEEE 802.1 Port
VLAN ID
IEEE 802.1 VLAN
Name
Impact
System value changed to the Port VLAN identifier in the TLV.
The system value is changed to the TLV VLAN
Identifier. L2Q will be set to 1 (ON).
VLAN Name TLV is only effective if:
● The deskphone is not registered with the Call
Server.
● Name begins with VOICE (case does not matter).
●
●
The VLAN is not zero.
DHCP Client is activated.
● The deskphone is registered but is not tagging layer 2 frames with a non-zero VLAN
ID.
If VLAN Name causes the deskphone to change
VLAN and the deskphone already has an IP
Address the deskphone will release the IP Address and reset.
If the TLV VLAN ID matches the VLAN ID the deskphone is using, the VLAN ID is marked as set by LLDP. Otherwise, if already registered, the deskphone waits until there are no active calls, releases its IP Address, turns on tagging with the
TLV VLAN ID, sets L2Q to "on," changes the default
L2Q to "on," and resets. If there is no valid IP
Address, the deskphone immediately starts tagging with the new VLAN ID without resetting.
Issue 5 May 2014 81
Administering Deskphone Options
Table 12: Impact of TLVs Received by 1600 Series IP Deskphones on System Parameter
Values (continued)
System
Parameter Name
TLV
Name
L2Q, L2QVLAN,
L2QAUD,
L2QSIG,
DSCPAUD,
DSCPSIG
MED Network
Policy TLV
MCIPADD
TLSSRVR and
HTTPSRVR
L2Q
Proprietary Call
Server TLV
Proprietary File
Server TLV
Proprietary 802.1
Q Framing
Proprietary - PoE
Conservation TLV
Extended
Power-Via-MDI
Impact
L2Q - set to “2” (off) If T (the Tagged Flag) is set to
0; set to “1” (on) if T is set to 1.
L2QVLAN - set to the VLAN ID in the TLV.
L2QAUD and L2QSIG - set to the Layer 2 Priority value in the TLV.
DSCPAUD and DSCPSIG - set to the DSCP value in the TLV.
A check is made as to whether a reset is necessary to obtain a new IP address due to a change in the values of the parameters L2Q or L2QVLAN.
This TLV is ignored if:
● the value of USE_DHCP is “0” and the value of IPADD is not “0.0.0.0”, or
●
● the Application Type is not 1 (Voice) and is not 2 (Voice Signaling), or the Unknown Policy Flag (U) is set to 1.
MCIPADD will be set to this value if it has not already been set.
TLSSRVR and HTTPSRVR will be set to this value if neither of them have already been set.
The default L2Q is set to the value of this TLV. No change is made to the current L2 tagging, but the new default value is used on the next reboot. If TLV
= 1, L2Q set to "1" (On). If TLV = 2, L2Q set to "2"
(Off). If TLV = 3, L2Q set to "0" (Auto).
This proprietary TLV can initiate a power conservation mode. The deskphones that support this will turn on/off the deskphone backlight and the backlight of an attached Button Module in response to this TLV.
Power conservation mode will be enabled if the received binary Power Source value is 10, and power conservation mode will be disabled if the received binary Power Source value is not 10.
Power conservation mode is enabled even if the deskphone is not powered over Ethernet because the deskphone sends information about the power source that it is using in a TIA LLDP MED Extended
Power-Via-MDI TLV; it is assumed that the power management system intends to conserve local power as well.
82 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Local Administrative Options Using the Deskphone Dialpad
Local Administrative Options Using the Deskphone
Dialpad
The local procedures you use most often as an administrator are:
● CLEAR - Remove all administered values, user-specified data, option settings, etc. and return a deskphone to its initial “out of the box” default values.
● DEBUG - Enable or disable debug mode for the button module serial port.
● GROUP - Set the group identifier on a per-phone basis.
● RESET - Reset all system values and system initialization values except AUTH, NVAUTH, registration extension, and password to the default values. Also resets the 802.1X identity and password to the default values.
● VIEW - Review the 1600 IP Deskphone system parameters to verify current values and file versions.
● Ethernet Interface Enable/Disable - Enable or disable the Ethernet Interface locally.
Clear Procedure
Sometimes, you might want to remove all administered values, user-specified data, and option settings.
Essentially, you want to return a deskphone to its initial “clean slate” or out of the box condition. This is usually done when passing a deskphone to a new, dedicated user when the user’s L O G O F F option is not sufficient. For example, a new user is assigned the same extension, but requires different permissions than the previous user.
The C L E A R option erases all administered data—static programming, file server and call server programming, and user settings including Contact button labels and locally programmed Feature button labels, and restores all such data to default values. The C L E A R option does not affect the software load itself. If you have upgraded the deskphone, the deskphone retains the latest software.
Once you have cleared a deskphone, you can administer it normally.
CAUTION:
!
CAUTION:
This procedure erases all administered data, without any possibility of recovering the data.
Issue 5 May 2014 83
Administering Deskphone Options
Use the following procedure to clear the deskphone of its administrative, user-assigned and options values.
1. While the deskphone is on-hook and idle, press the following sequence of keys on the faceplate of the deskphone:
Mute 2 7 2 3 8 2 5 3 2 7 # (Mute C R A F T C L E A R #)
Important:
Note:
!
Important:
2 7 2 3 8 is the default password. If you have changed that password by changing the value of PROCPSWD, replace 27238 with the latest password.
Note:
Press the Mute button momentarily. Do not press this button while pressing other keys/ buttons.
The following text displays left-justified at the top of the display:
Clear all values?
*=no #=yes
2. If you do not want to clear all values, press * (no) to terminate the procedure and retain the current values.
A screen displays the following prompt on the top line:
Are you sure?
*=no #=yes
3. Press the * button to terminate the procedure without clearing the values. Press the # button to clear all values to their initial default values.
A confirmation tone sounds and the following text displays left-justified at the top of the display:
Clearing values.
The deskphone is cleared to its “out of the box” state.
Note:
Disabling or enabling the Debug mode
Note:
The Debug mode is available only on the 1616 deskphone.
With Release 1.3.3, the Debug mode is available only if you change the default CRAFT password. You can change the password to any value between 0000 to 9999999.
84 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Local Administrative Options Using the Deskphone Dialpad
Use the following procedure to turn the debug mode for the button module serial port to on or off.
1. While the deskphone is on-hook and idle, press the following sequence of keys on the faceplate of the deskphone:
Mute XXXXX 3 3 2 8 4 # (Mute XXXXX D E B U G #) where XXXXX is the changed or non-default CRAFT password.
Important:
!
Important:
2 7 2 3 8 is the default password. If you have changed that password by changing the value of PROCPSWD, replace 27238 with the latest password.
Note:
Note:
Press the Mute button momentarily. Do not press this button while pressing other keys/ buttons.
2. After entry of the command sequence, the following displays, based on the current value of the system value NVDEBUG:
If NVDEBUG = 1: Debug mode= on
0=off #=OK
If NVDEBUG = 0: Debug mode= off
1=on #=OK
If a value different from the current NVDEBUG value is entered, the following text displays left-justified at the top of the display:
Save new value?
*=no #=yes
3. Press the * button to terminate the procedure, or the # button to save the new value. If you press the # button, the deskphone displays the following text:
New value being saved
The deskphone saves the new value.
Group Identifier
Use the following procedure to set or change the Group Identifier.
Note:
Note:
Perform this procedure only if the LAN Administrator instructs you to do so.
For more information about groups, see The GROUP System Value on page 59.
Issue 5 May 2014 85
Administering Deskphone Options
While the deskphone is on-hook and idle, press the following sequence of keys on the faceplate of the deskphone:
Mute 2 7 2 3 8 4 7 6 8 7 (Mute C R A F T G R O U P)
Important:
Note:
!
Important:
2 7 2 3 8 is the default password. If you have changed that password by changing the value of PROCPSWD, replace 27238 with the latest password.
Note:
Press the Mute button momentarily. Do not press this button while pressing other keys/ buttons.
The following text displays left-justified at the top of the display:
Group= ddd
New=_ where ddd is the Group value.
1. Enter a valid Group value (0-999).
If a value different from the current Group value is entered, the following text displays left-justified at the top of the display:
Save new value?
*=no #=yes
2. Press the * button to terminate the procedure, or the # button to save the new value.
If you press the # button, the following text displays:
New value being saved
The new value is saved and the user interface is restored to its previous state.
Reset System Values
Use the following procedure to reset all system values and system initialization values except AUTH,
NVAUTH, registration extension, and password to the default values. Also resets the 802.1X identity and password to the default values.
CAUTION:
!
CAUTION:
This procedure erases all static information except the extension number and password, without any possibility of recovering the data.
86 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Local Administrative Options Using the Deskphone Dialpad
Important:
Note:
1. While the deskphone is on-hook and idle, press the following sequence of keys on the faceplate of the deskphone:
Mute 2 7 2 3 8 7 3 7 3 8 # (Mute C R A F T R E S E T #)
!
Important:
2 7 2 3 8 is the default password. If you have changed that password by changing the value of PROCPSWD, replace 27238 with the latest password.
Note:
Press the Mute button momentarily. Do not press this button while pressing other keys/ buttons.
The IP deskphones display the following text left-justified at the top of the display:
Reset values?
*=no #=yes
CAUTION:
!
CAUTION:
As soon as you press the # button, all static information except the extension number and password will be erased, without any possibility of recovering the data.
2. If you do not want to reset the system values, press * (no) and proceed to Step 4.
The following prompt displays on the top line:
Are you sure?
*=no #=yes
3. Press the * button to continue without resetting the values and proceed to Step 4. Or, press the # button to reset values to their defaults.
All deskphones display the following text left-justified at the top of the display while the system values are reset to defaults:
Resetting values.
The deskphone resets from the beginning of registration, which takes a few minutes.
4. If you do not reset the deskphone, the deskphone displays the following prompt:
Restart phone?
*=no #=yes
5. Press the * key to terminate the procedure without restarting the deskphone. Otherwise, press # and perform the following Restart procedure.
Issue 5 May 2014 87
Administering Deskphone Options
Restart the Deskphone
Use the following procedure to restart the deskphone.
1. While the deskphone is on-hook and idle, press the following sequence of keys on the faceplate of the deskphone:
Mute 2 7 2 3 8 7 3 7 3 8 # (Mute C R A F T R E S E T #)
Important:
Note:
!
Important:
2 7 2 3 8 is the default password. If you have changed that password by changing the value of PROCPSWD, replace 27238 with the latest password.
Note:
Press the Mute button momentarily. Do not press this button while pressing other keys/ buttons.
The IP deskphone displays the following text left-justified at the top of the display:
Reset values?
*=no #=yes
2. Press the # button to reset values to their defaults, or * to continue a restart without resetting the values to their defaults.
The deskphones display the following text left-justified at the top of the display while the system values are reset to defaults:
Resetting values.
Once the system values are reset, the following prompt displays on all IP deskphones:
Restart phone?
*=no #=yes
3. Press the * key to terminate the procedure without restarting the deskphone.
Press the # key to restart the deskphone.
The remainder of the procedure depends on the status of the boot and application files.
88 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Interface Control
Interface Control
Use the following procedure to set or change the interface control value.
1. While the deskphone is on-hook and idle, press the following sequence of keys on the faceplate of the deskphone:
Mute 2 7 2 3 8 4 6 8 # (Mute C R A F T I N T #)
Important:
!
Important:
2 7 2 3 8 is the default password. If you have changed that password by changing the value of PROCPSWD, replace 27238 with the latest password.
Note:
Note:
Press the Mute button momentarily. Do not press this button while pressing other keys/ buttons.
2. After entry of the command sequence, deskphones with an internal Ethernet switch display the following text, depending on the current interface control value:
PHY1= status
*=change #=OK where status is the value of PHY1STAT, defined as:
● Status is auto when PHY1STAT = 1
● Status is 10Mbps HDX when PHY1STAT = 2
● Status is 10Mbps FDX when PHY1STAT = 3
● Status is 100Mbps HDX when PHY1STAT = 4
● Status is 100Mbps FDX when PHY1STAT = 5
3. To change the PHY1 value, press *.
Depending on the current value, the next sequential valid PHY1 value is selected and displayed as the status. For example, if the current value is 10Mbps HDX (2), pressing * changes the value to 3
(10Mbps FDX).
4. Press the * button to terminate the procedure, or the # button to save the new value. If you press the # button, the following text displays:
PHY2= status
*=change #=OK where status is the value of PHY2STAT, defined as:
● Status is disabled when PHY2STAT = 0
● Status is auto when PHY2STAT = 1
Issue 5 May 2014 89
Administering Deskphone Options
● Status is 10Mbps HDX when PHY2STAT = 2
● Status is 10Mbps FDX when PHY2STAT = 3
90 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Interface Control
● Status is 100Mbps HDX when PHY2STAT = 4
● Status is 100Mbps FDX when PHY2STAT = 5
5. To change the PHY2 value, press *.
Depending on the current value, the next sequential valid PHY2 value is selected and displayed as the status. For example, if the current value is 10Mbps HDX (2), pressing * changes the value to 3
(10Mbps FDX).
The following text displays left-justified at the top of the display:
Save new value?
*=no #=yes
6. Press the * button to terminate the procedure, or the # button to save the new values.
If you press the # button, the following text displays.
New value being saved
The new values are saved and a restart occurs automatically. The user interface is restored to its previous state.
The View Local Procedure
If you are using static addressing and encounter problems, use the following procedure to verify the current values of system parameters and file versions.
Issue 5 May 2014 91
Administering Deskphone Options
Important:
Note:
1. While the deskphone is on-hook and idle, press the following sequence of keys on the faceplate of the deskphone:
Mute 2 7 2 3 8 8 4 3 9 # (Mute C R A F T V I E W #)
!
Important:
2 7 2 3 8 is the default password. If you have changed that password by changing the value of PROCPSWD, replace 27238 with the latest password.
Note:
Press the Mute button momentarily. Do not press this key while pressing other keys.
The following text displays left-justified at the top of the display:
View settings
*=next #=exit
2. Press the * button at any time during viewing to display the next name and system value pair or filename from Table 13 . The first pair returns after the last pair displays. Values that cannot display on one line wrap to the next line.
Press the # button at any time during viewing to terminate the procedure and restore the user interface to its previous state. The names and values display in the following order:
Table 13: Parameter Values
Name
Model
System Value
16ccDccc
Phone SN
PWB SN
PWB comcode
MAC address
cccccccccccccccccc
cccccccccccccccccc
nnnnnnnnn
hh:hh:hh:hh:hh:hh
Format
Up to 8 ASCII characters: MODEL value.
Deskphone Serial Number, up to 18
ASCII characters.
Printed Wiring Board (circuit board)
Serial Number, up to 18 ASCII characters. Applies only to 16xx IP
Deskphones that have a software-readable PWB serial number and comcode.
9 ASCII numeric characters. Applies only to 16xx IP Deskphones that have a software-readable PWB serial number and comcode.
Each octet of the MAC address displays as a pair of hexadecimal numbers.
1 of 3
92 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Interface Control
Table 13: Parameter Values (continued)
Name
L2 tagging
VLAN ID
IP address
Subnet mask
Router
File server
Call server
802.1X
Group
System Value Format
ccccccccc
cccc
Up to 9 ASCII characters:
“on” if NVL2Q = 1
“off” if NVL2Q = 2
“auto: on” if NVL2Q = 0 and 802.1Q tagging is on
“auto: off” if NVL2Q = 0 and 802.1Q tagging is off
Up to 4 ASCII characters. Value is
L2QVLAN if 802.1Q tagging is on or
“none” of 802.1Q tagging is off.
nnn.nnn.nnn.nnn
nnn.nnn.nnn.nnn
Up to 15 ASCII characters:
IPADD value.
Up to 15 ASCII characters:
NETMASK value.
nnn.nnn.nnn.nnn Up to 15 ASCII characters: the IP address of the router in use.
nnn.nnn.nnn.nnn.nnnnn Up to 21 ASCII characters: IP address and port of last file server used successfully during initialization or
“0.0.0.0” if no file server was used successfully.
nnn.nnn.nnn.nnn.nnnnn Up to 21 ASCII characters: IP address and port of the call server currently in use, otherwise “0.0.0.0.”
If DOT1X = 0
If DOT1X = 1
If DOT1X = 2
nnn
Pass-thru mode.
Pass-thru with Logoff.
Supplicant mode.
Up to 3 ASCII numeric characters:
GROUP value.
2 of 3
Issue 5 May 2014 93
Administering Deskphone Options
Table 13: Parameter Values (continued)
Name
Protocol:
System Value
cccccccc
filename.ext
cccccccc Ethernet
bootcodename
Button Module 1 cccccccccccccc
Button Module 2 cccccccccccccc
Button Module 3 cccccccccccccc
Format
Up to 8 ASCII characters, currently only
“H.323.”
4 to 32 ASCII characters. The name of the primary ("big app") image file currently stored in the deskphone
(endptAPPINUSE).
2 to 7 ASCII characters, either
“100Mbps”, “10Mbps”, or “No” depending on the current speed of the
Ethernet line interface.
1 to 32 ASCII characters. The name of the backup ("little app") image file currently stored in the deskphone
(endptBOOTNAME).
Up to 14 ASCII characters. The version identifier of the software in the Button
Module, if applicable.
Up to 14 ASCII characters. The version identifier of the software in the Button
Module, if applicable.
Up to 14 ASCII characters. The version identifier of the software in the Button
Module, if applicable.
3 of 3
Static Addressing Installation
The usual way to assign IP addresses to IP deskphones is the automatic method. There might be times, however, when manual assignment of IP addresses is desired.
!
CAUTION:
Static addressing is necessary when a DHCP server is unavailable.
CAUTION:
Because of the increased opportunities for text entry errors associated with static addressing, we very strongly recommend that a DHCP server be installed and static addressing avoided.
Use the following procedure to invoke manual address information programming.
1. Start manual address programming by performing one of the following steps:
94 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Interface Control
Important:
Note: a. During normal DHCP processing, press the * key while “* to program“ displays during the
DHCP process.
or b. While the deskphone is on-hook and idle, press the following sequence of keys on the faceplate of the deskphone:
Mute 2 7 2 3 8 2 3 3 7 # (Mute CRAFT A D D R #)
!
Important:
2 7 2 3 8 is the default password. If you have changed that password by changing the value of PROCPSWD, replace 27238 with the latest password.
Note:
Press the Mute button momentarily. Do not press this button while pressing other keys/ buttons.
The deskphone displays:
Phone= nnn.nnn.nnn.nnn
New=_ where nnn.nnn.nnn.nnn is the current IP address system value of the deskphone.
2. Enter the deskphone’s IP address followed by the # button.
The deskphone displays:
CallSv= nnn.nnn.nnn.nnn
New=_ where nnn.nnn.nnn.nnn is the current system value of the media server/gatekeeper IP address.
3. Enter the Gatekeeper IP address followed by the # button.
The deskphone displays:
Router= nnn.nnn.nnn.nnn
New=_ where nnn.nnn.nnn.nnn is the current system value of the gateway/router IP address.
4. Enter the Gateway router IP address followed by the # button.
The deskphone displays:
Mask= nnn.nnn.nnn.nnn
New=_ where nnn.nnn.nnn.nnn is the current system value of the IP netmask.
Issue 5 May 2014 95
Administering Deskphone Options
5. Enter the IP netmask followed by the # button.
The deskphone displays:
FileSv= nnn.nnn.nnn.nnn
New=_ where nnn.nnn.nnn.nnn is the current system value of the HTTP/HTTPS server IP address.
6. Enter the File server followed by the # button.
The deskphone displays one of the following texts, depending on the current setting of the system parameter NVL2Q (802.1Q):
If NVL2Q is 0: 802.1Q=auto
*=change #=OK
If NVL2Q is 1: 802.1Q=on
*=change #=OK
If NVL2Q is 2: 802.1Q=off
*=change #=OK
7. Press * to change 802.1Q to the next sequential value. For example, if the current value is 0 (auto) pressing * changes it to 1 (on) and if the current value is 2 (off), pressing * changes it to 0 (auto).
The display is updated to show the current status of 802.1Q.
8. Press the # button to continue the procedure without changing the displayed status of 802.1Q
The deskphone displays the following text:
VLAN ID= dddd
New=_ where dddd is the current system value of the 802.1 VLAN ID.
9. Enter a valid value between 0 and 4094 for the new value of the 802.1 VLAN ID.
The deskphone displays the following message:
VLAN test= ddd
New=_ where ddd is the number of seconds to wait for a DHCPOFFER on a non-zero VLAN.
96 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Interface Control
10. Enter a valid value between 0 and 999 for the new value of the DHCPOFFER wait period.
The deskphone displays:
Save new values?
*=no #=yes
11. Press the # button to save the new values you entered.
The deskphone displays:
New values being saved
Once the new values are stored, the deskphone is reset.
If a new boot program is downloaded from the HTTP server after you enter static addressing information, you must reenter your static addressing information.
Disable/Enable Event Logging
Use the following procedure to enable or disable logging of system events.
1. While the deskphone is on-hook and idle, press the following sequence of keys on the faceplate of the deskphone:
Mute 2 7 2 3 8 5 6 4 # (Mute C R A F T L O G #)
Important:
!
Important:
2 7 2 3 8 is the default password. If you have changed that password by changing the value of PROCPSWD, replace 27238 with the latest password.
Note:
Note:
Press the Mute button momentarily. Do not press this button while pressing other keys/ buttons.
2. After entry of the command sequence, the deskphone displays the following text, depending on the current value of the system parameter NVLOGSTAT:
Log= status
*=change #=OK where status is the type of logging indicated by the NVLOGSTAT value, defined as:
● Status is disabled when NVLOGSTAT = 0
● Status is emergencies when NVLOGSTAT = 1
● Status is alerts when NVLOGSTAT = 2
Issue 5 May 2014 97
Administering Deskphone Options
● Status is critical when NVLOGSTAT = 3
● Status is errors when NVLOGSTAT = 4
● Status is warnings when NVLOGSTAT = 5
● Status is notices when NVLOGSTAT = 6
● Status is information when NVLOGSTAT = 7
● Status is debug when NVLOGSTAT = 8
3. To change the logging status, press *.
Depending on the current value, the next sequential valid NVLOGSTAT value is selected and displayed as the status. For example, if the current value is alerts (2), pressing * changes the value to 3 (critical). If the current value is debug (8), pressing * changes the value to 0 (disabled).
If a value different from the current NVLOGSTAT value is entered, the following text displays left-justified at the top of the display:
Save new value?
*=no #=yes
4. Press the * button to terminate the procedure, or the # button to save the new value. If you press the # button, the deskphone displays the following text:
New value being saved
The deskphone saves the new value.
Logoff
Use the following procedure to log off a deskphone.
CAUTION:
!
CAUTION:
Once a deskphone is logged off, a password and extension might be needed to log back on.
1. While the deskphone is on-hook and idle, press the following sequence of keys on the faceplate of the deskphone:
Mute 2 7 2 3 8 5 6 4 6 3 3 # (Mute C R A F T L O G O F F #)
Important:
!
Important:
2 7 2 3 8 is the default password. If you have changed that password by changing the value of PROCPSWD, replace 27238 with the latest password.
98 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Interface Control
Note:
Note:
Press the Mute button momentarily. Do not press this button while pressing other keys/ buttons.
2. After entry of the command sequence, the deskphone unregisters from the call server. The deskphone display clears and then displays the following prompt for subsequent login:
Enter Extension
EXT= #=OK
Self-Test Procedure
Note:
Note:
Replace variable w/ short product name stores two software code images in reprogrammable non-volatile memory. The primary image, called the “big app” must be running to perform a self-test. The backup image, called the “little app” does not support the self-test.
For self-testing, use the following procedure:
1. To invoke Replace variable w/ short product name self-test procedures, press the following sequence of keys on the faceplate of the deskphone:
Mute 2 7 2 3 8 8 3 7 8 # (Mute C R A F T T E S T #)
Important:
!
Important:
2 7 2 3 8 is the default password. If you have changed that password by changing the value of PROCPSWD, replace 27238 with the latest password.
Issue 5 May 2014 99
Administering Deskphone Options
Note:
Note:
Press the Mute button momentarily. Do not press this button while pressing other keys/ buttons.
All deskphones show the following text, left-justified at the top of the display, for 1 second after self-test is invoked:
Self test
#=end
A block character with all pixels on then displays in all display character locations for
5 seconds. Display of the block character helps to find bad display pixels.
The deskphone displays one of the following:
If self-test passes: Self test passed
#=end
If self-test fails: Self test failed
#=end
2. To terminate the self-test, press the # button on the dial pad at any time. Doing so generates a confirmation tone, and returns the user interface to its previous state.
100 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Language Selection
Language Selection
1600 Series IP Deskphones are factory-set to display information in the English language. The languages available depend of the type of deskphone you have. The following 1600 Series IP
Deskphones are available:
● Global deskphones
- 1603
- 1603SW
- 1608
- 1616
● International deskphones
- 1603-I
- 1603SW-I
- 1608-I
- 1616-I
1600 Series Global Deskphones
The 1600 Series Global Deskphones consist of the following deskphone models:
● 1603
● 1603SW
● 1608
● 1616
As of Release 1.0, all software downloads include language files for 9 additional languages.
Administrators can specify from one to four of those languages per deskphone to replace English. End users can then select which of those languages they want their deskphone to display.
All downloadable language files contain:
● UTF-16 encoded Unicode characters (only)
● a file name ending in .txt
● the language name as it should be presented to the user for selection
● a translation of each available language name into all other languages
● an indication of the preferred character input method as shown in
Issue 5 May 2014 101
Administering Deskphone Options
● text string replacements for the built-in English text strings, for example, entry prompts and error messages
● an indication of the font corresponding to the language
Table 14: Language Files Available with Software Downloads for 1600 Series Global
Deskphones
Language Font
Dutch
English
French (Canadian)
French (Parisian)
German
Italian
Portuguese (Brazilian)
Russian
Spanish (Castilian)
Spanish (Latin American)
Character Input Method to be specified in each respective language file
Latin-1
Latin-1
French
French
German
Italian
Portuguese
Russian
Spanish
Spanish
Default
Default
Default
Default
Default
Default
Default
Default
Default
Default
Note:
Note:
The 1600 Series Global Deskphones also support half-width Katakana.
There are no dependencies between the languages available from the software download and the actual character input method. If a character input method is not supported, ASCII is used instead.
Acceptable input methods are as follows:
● ASCII
● Latin-1
● German
● French
● Italian
● Spanish
● Portuguese
102 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Language Selection
Use the configuration file and these parameters to customize the settings for up to four languages:
● LANGxFILE - The name of a selected language file, for example, "French". In addition to providing the language name as this value, replace the "x" in this parameter with a "1", "2", "3", or
"4" to indicate which of four languages you are specifying. For example, to indicate German and
French are the available languages, the setting is: LANG1FILE=mlf_german.txt and
LANG2FILE=mlf_french.txt.
● LANG0STAT - Allows the user to select the built-in English language when other languages are downloaded. If LANG0STAT is "0" and at least one language is downloaded, the user cannot select the built-in English language. If LANG0STAT is "1" the user can select the built-in English language text strings.
● LANGSYS = The file name of the system default language file, if any.
For more information, see 1600 Series IP Deskphone Customizable System Parameters . To view
multiple language strings, see the MLS local procedure in the Avaya 1600 Series IP Deskphones
Installation and Maintenance Guide.
Note:
Note:
Specifying a language other than English in the configuration file has no impact on Avaya
Aura Communication Manager settings, values, or text strings.
1600 Series International Deskphones
The 1600 Series International Deskphones consist of the following deskphone models:
● 1603-I
● 1603SW-I
● 1608-I
● 1616-I
As of Release 1.1, all software downloads include language files for six additional languages.
Administrators can specify one of those languages per deskphone to replace English.
All downloadable language files contain:
● UTF-16 encoded Unicode characters (only)
● a file name ending in .txt. (This is the language file.)
● a file name ending in .lzma. (This is the font file.)
● the language name as it should be presented to the user for selection
● a translation of each available language name into all other languages
● an indication of the preferred character input method as shown in Table 15
● text string replacements for the built-in English text strings, for example, entry prompts and error messaged
Issue 5 May 2014 103
Administering Deskphone Options
Note:
● an indication of the font corresponding to the language
Note:
The 1600 Series International Deskphones also require a font file (*.lzma) that must be paired with the language file. Both the language file and corresponding font file must reside on the HTTP server.
Table 15: Language Files Available with Software Downloads for 1600 Series
International Deskphones
Language Font
Arabic
Chinese - Simplified
Character Input Method to be specified in each respective language file
Latin-1
Latin-1
Chinese - Traditional Latin-1
Hebrew Latin-1
Japanese Katakana
Korean
Latin-1
Latin-1
Arabic/Hebrew
Simplified
Chinese
Traditional
Chinese
Arabic/Hebrew
Default
Korean
Note:
Note:
The 1600 Series International Deskphones also support half-width Katakana.
There are no dependencies between the languages available from the software download and the actual character input method. If a character input method is not supported, ASCII is used instead.
Acceptable input methods are as follows:
● ASCII
● Arabic
● Chinese - Simplified
● Chinese - Traditional
● Hebrew
● Korean
Use the configuration file and these parameters to customize the settings for one language:
● FONTFILE - The name of the selected font file for a language to be downloaded. You must specify this parameter for any language except Japanese Katakana. For example, to use Arabic, the setting is: SET FONTFILE Arabic_b004i.rbm.lzma.
104 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Language Selection
Note:
Note:
Arabic and Hebrew share one font file.
● LANGxFILE - The name of a selected language file. In addition to providing the language name as this value, replace the "x" in this parameter with a "1" For example, to use Arabic, the setting is:
SET LANG1FILE=mlf_arabic_b004i.txt.
● LANG0STAT - Allows the user to select the built-in English language when other languages are downloaded. If LANG0STAT is "0" and at least one language is downloaded, the user cannot select the built-in English language. If LANG0STAT is "1" the user can select the built-in English language text strings.
● LANGSYS = The file name of the system default language file, if any.
For more information, see 1600 Series IP Deskphone Customizable System Parameters . To view
multiple language strings, see the MLS local procedure in the Avaya 1600 Series IP Deskphones
Installation and Maintenance Guide.
Note:
Note:
Keep in mind the following information:
- Specifying a language other than English in the configuration file has no impact on Avaya
Aura Communication Manager settings, values, or text strings.
- You can download only one language (with the corresponding font file and language file) at a time.
- The font files for the five languages also contain the font information for the languages supported on the 1600 Series Global Deskphones.
- You can use the GROUP feature to logically separate the 1600 Series Global Deskphones from the 1600 Series International Deskphones in one enterprise network by specifying different language/font files in the 46xxsettings.txt file.
Issue 5 May 2014 105
Administering Deskphone Options
Enhanced Local Dialing
The 1600 Series IP Deskphones have a variety of telephony-related applications that might obtain a deskphone number during operation. For example, the Call Log saves a number of an incoming caller.
The deskphones can evaluate a raw deskphone number. Based on administered parameters, the deskphone can automatically prepend the correct digits, saving the user time and effort. This is the
Enhanced Dialing feature. The key to the success of this feature is accurate administration of several important values, summarized below.
Note:
Note:
In all cases, the values you administer are the values relevant to the location of the
Avaya Media Server at which the IP deskphones are registered. If a deskphone is in
Japan, but its media server is in the United States, set the PHNCC value to “1" for the
United States.
In all cases, the digits the deskphones insert and dial are subject to standard Avaya
Media Server features and administration. This includes Class of Service (COS), Class of Restriction (COR), Automatic Route Selection (ARS), and so on.
, you can administer the system parameter ENHDIALSTAT to turn off the Enhanced Local Dialing feature.
The system values relevant to the Enhanced Dialing Feature are:
● PHNCC - the international country code of the media server.
For example, “1” for the United States, “44” for the United Kingdom, and so on.
● PHNDPLENGTH - the length of the dial plan on the media server.
● PHNIC - the digits the media server dials to access public network international trunks.
For example, “011” for the United States.
● PHNLD - the digit dialed to access public network long distance trunks on the media server.
● PHNLDLENGTH - the maximum length, in digits, of the national deskphone number for the country in which the Avaya Media Server is located.
● PHNOL - the character(s) dialed to access public network local trunks on the media server.
106 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Backup/Restore
Backup/Restore
The 1600 Series IP Deskphones support the HTTP client to back up and restore the user-specific data indicated in Table 17 . For backup, the deskphone creates a file with all the user-specific data if a backup file location is specified in system parameter BRURI. The file is sent to the server by an HTTP
PUT message, with appropriate success or failure confirmation.
For restore, the initiating process must supply only the backup file name. The file is requested from the server by an HTTP GET message. If successful, the file is returned to the initiating process, otherwise a failure message is returned.
Backup and restore operations construct the URI used in the HTTP message from the value of the
BRURI parameter and from the file name as follows:
● If BRURI ends with / (a forward slash), the file name is appended.
● Otherwise, a forward slash is appended to the BRURI value, then the file name is appended to that.
Note:
Note:
A directory path and/or a port number can be included in BRURI as specified in IETF
RFCs 2396 and 3986.
HTTP authentication is supported for both backup and restore operations. The authentication credentials and realm are stored in re-programmable, non-volatile memory, which is not overwritten when new deskphone software is downloaded. Both the authentication credentials and realm have a default value of null, set at manufacture or at any other time user-specific data is removed from the deskphone.
The new value(s) replace the currently stored values when HTTP authentication for backup or restore succeeds.
If HTTP authentication fails, the user is prompted to enter new credentials.
Note:
Note:
Users can request a backup or restore using the Advanced Options Backup/Restore screen, as detailed in the user guide for their specific deskphone model. or specific error messages relating to Backup/Restore, see the Avaya 1600 Series IP Deskphones
Installation and Maintenance Guide.
Issue 5 May 2014 107
Administering Deskphone Options
Backup
When the system parameter BRURI is non-null, user changes are automatically backed up to the file
ext_16xxdata.txt (where ext is the value of NVPHONEXT) on the HTTP server to a user-specified directory. Backup formats are as follows:
Table 16: Backup File Formats
Item/Data Value
Generic
Contacts
Format
name=value
ABKNAMEmmm=ENTRY_NAME
ABKNUMBERmmm=ENTRY_NUM
BER_1
(where mmm is the one-, two-, or three-digit entry ID, with leading zeros for single and double-digit entry IDs)
In addition to the parameters listed in
Table 9 , a backup saves the options and non-password
parameters shown in Table 17 .
108 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Backup/Restore
Table 17: Options and Non-Password Parameters Saved During Backup
Parameter Name
LANGUSER
LOGACTIVE
LOGBRIDGED
LOGLINEAPPS
LOGOTHERANS
OPTAGCHAND
OPTAGCHEAD
OPTAGCSPKR
OPTAUDIOPATH
OPTCLICKS
OPTERRORTONE
PERSONALRING
PHNREDIAL
PHNSCRONCALL
PHNSCRONALERT
PHNTIMERS
PHNVISUALALERT
Setting
Display Language
Call Log Active
Log Bridged Calls
Log Line Calls
Log Calls Answered By Others
Handset Automatic Gain Control
Headset Automatic Gain Control
Speaker Automatic Gain Control
Audio Path
Button Clicks
Error Tone
Personalized Ring
Redial
Go to Phone Screen on Calling
Go to Phone Screen on Ringing
Call Timer
Visual Alerting
Restore
When automatic or user-requested retrieval of backup data is initiated, system values and internal values are set to values contained in the backup file. This occurs only if the OPSTAT parameter setting allows the user to change those values. Therefore, any restrictions set using OPSTAT are recognized and honored.
The backup file value is not retrieved, and the current setting remains valid:
● when a value in the backup file has changed and
● that value corresponds to an application that OPSTAT indicates should not be changed.
This prevents a user from bypassing the administration of OPSTAT and changing options settings in the backup file.
Issue 5 May 2014 109
Administering Deskphone Options
Note:
Note:
If you administered the APPSTAT parameter to suppress changes to one or more applications, the deskphone backs up and restores data as usual, but ignores data for
“suppressed” applications. This prevents a user from bypassing your APPSTAT restrictions by editing the backup file. For information about APPSTAT, see
Application Status Flag (APPSTAT) on page 114.
During backup file restoration, user activity is prohibited until a Restore successful or Restore
Failed message displays. When a restore attempt fails, if a retrieved file has no valid data, or if a retrieved file cannot be successfully stored, a Retrieval Failed message displays at the deskphone until the user takes another action.
Data retrieval considerations are as follows:
● When you create a backup file rather than edit an existing one, be sure to create the file with
UTF-16 LE (little endian) characters, with Byte Order Mark (BOM) for LE of 0xFFFE.
● Backup saves data values using the generic format name=value. For specific formats, see
● All identifiers, for example, names, are interpreted in a case-insensitive manner, but the case of parameter values, Contact names, and numbers is preserved.
● Spaces preceding, within, or following a name are treated as part of the name.
● <CR> and <LF> (UTF-16 characters 0x000D and 0x000A, respectively) are interpreted as line termination characters.
● Blank lines are ignored.
● When an identifier is not recognized or is invalid, the entire line is ignored. Likewise, if an identifier is valid but the data itself is invalid or incomplete, the line is ignored.
● When an identifier is valid with valid and complete data, but the data is not applicable to the current state of the deskphone, the data is retained for possible use later, and is considered data to be backed up at the appropriate time.
● When more than one line contains a value for an option, parameter, or Contacts entry, the last value read is retrieved, to allow new values to overwrite previous values as lines are read from the backup file. In all other cases, the line order in the backup file has no bearing on retrieval.
● The existence of invalid data does not constitute a failed retrieval. The success of the retrieval process requires the deskphone to obtain the backup file and successfully restore valid data.
110 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Chapter 8: Administering Applications and Options
Customizing 1600 Series IP Deskphone Applications and
Options
The 1600 Series IP Deskphones have some unique and powerful capabilities that take advantage of their display and access to LAN facilities. You need to provide the information called for in relevant
sections of Table 18 in a customized script file. For more information, see
Scripts and Application Files on page 56.
CAUTION:
!
CAUTION:
For the deskphones to work properly, you must have a 46xxsettings.txt file in the same directory as the application file. If you do not edit the 46xxsettings.txt file, those deskphones use default settings only. The 46xxsettings file is available as a standalone download. If you already have such a file because you downloaded it for a previous 1600
Series, 9600 Series, or 4600 Series IP Deskphone release, installing the standalone file overwrites the original file.
Note:
Note:
To facilitate administration, the 1600 Series, 9600 Series, and 4600 Series IP
Deskphones use the same 46xxsettings.txt file.
In Table 18 , parameters shown with a Mandatory status must be accurate and non-null for the
application to work. You can change parameters with an Optional status to suit your environment. If you do not change parameters, the defaults are used.
Issue 5 May 2014 111
Administering Applications and Options
Table 18: 1600 Series IP Deskphone Customizable System Parameters
Parameter Name Default Value Status Description and Value Range
General User Parameters:
APPSTAT 1
OPSTAT 111
Optional Applications status flag. See
description. See
for the range of values.
Optional Options status flag(s) (1 or 3 ASCII numeric digits) indicate which options are user-selectable. The default of 111 grants access to all options and related applications.
Single digit valid values are:
1=user can access all options, including Logout,
2= user can access only view-oriented applications.
Three-digit valid values are a concatenation of binary values, in the form abc, where each letter represents a 0 (disabled/off) or 1
(enabled/on), interpreted as:
a = base settings for all user options and related applications, except as noted in b or c.
b = setting for view-oriented applications (for example, the
Network Information application), as applicable.
c = setting for Logout application, if applicable.
The binary "0" does not allow an end user to see or invoke options and related applications. The binary "1" allows full display and access to all options and related applications.
1 of 2
112 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Customizing 1600 Series IP Deskphone Applications and Options
Table 18: 1600 Series IP Deskphone Customizable System Parameters (continued)
Parameter Name Default Value Status Description and Value Range
Web Access Application Parameters:
SUBSCRIBELIST " " (Null)
TPSLIST " " (Null)
Optional Subscription list for potential pushed content. List of zero or more fully qualified URLs, separated by commas without intervening spaces, with up to 255 total characters.
Optional List of Trusted Push Servers. List of zero or more fully qualified domain/ path strings, separated by commas without intervening spaces, with up to 255 total characters. For more information, see the 9600 Series IP
Deskphone Application Programmer
Interface (API) Guide (Document
Number 16-601442).
Backup/Restore Parameters
BRURI " " (Null) Mandator y
URL used for backup and retrieval of user data. Specify HTTP server and directory path to backup file. Do not specify backup file name. Value:
0-255 ASCII characters. Null is a valid value and spaces are allowed.
If this value is null or begins with a character sequence other than http:/
/ or https:// the Backup/Restore option will not display to the deskphone user.
Backlight Parameters
BAKLIGHTOFF 120 Optional Number of idle minutes after which the backlight turns off (1-3 ASCII digits, from 0-999).
2 of 2
Issue 5 May 2014 113
Administering Applications and Options
The Application Status Flag (APPSTAT)
The 1600 Series IP Deskphones offer the user numerous applications like Contacts, Call Log, Redial, and so on. Each of these applications allows the user to add, delete, or in some cases, edit entries.
You, as the administrator, might not want the user to have that level of functionality. For example, a hotel lobby deskphone probably should not allow a user to delete the concierge’s contact number.
Further, for privacy reasons, that same deskphone should not allow a Call Log display. You can use the
Application Status Flag, APPSTAT, to administer specific application functionality permission levels for one or more deskphones.
APPSTAT consists of one number, specifying a certain level of allowed functionality. A Zero (“0”) value is the most limiting setting. Values “2” and “3” allow increasing levels of functionality, and “1” allows the user complete application functionality.
Table 19: Application Status Flags and Their Meaning
APPSTAT Value Meaning
0
1
2
3
Redial and Call Log are suppressed. Contact changes are not allowed.
All administered applications are displayed, with full functionality.
This is the default value.
Call Log is suppressed. Contact changes are not allowed. Only one-number Redial is allowed.
Contact changes are not allowed.
and so on are not labeled or displayed. Options associated with suppressed applications can continue to display unless you override them by appropriate OPSTAT parameter administration. Displayed options have no effect while the application is suppressed.
In Table 19 , “Contact changes are not allowed” means the Contact application displays and the user
can make calls as normal. Any controls that allow the user to change any aspect of the Contact application do not display. This restriction includes the ability to add, delete, or edit any Contact name or number.
In Table 19 , “Only one-number Redial is allowed” means the user Option that allows a choice between
displaying last numbers dialed is suppressed. The Redial buffer stores only one number. The Redial application does not display since the user can redial only one number. This restriction allows privacy once a given user has left the deskphone.
You can:
● set APPSTAT to 1, for example, in a staging area,
● administer a given deskphone with Contact entries of your choice, like the Concierge deskphone
number button in the earlier example,
● then move the deskphone to where it will be used, where you have administered APPSTAT to be, for example, 0 (zero).
114 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Customizing 1600 Series IP Deskphone Applications and Options
When the relocated deskphone resets, it retains its Contact entries, like Concierge, but does not allow the user to create new entries.
When you set APPSTAT to any valid value other than 1, the deskphone does not accept any Contact button label changes that might have been made directly on a backup file. Only the existing labels of the deskphone are used. This restriction prevents circumvention of the APPSTAT restrictions.
Issue 5 May 2014 115
Administering Applications and Options
116 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Appendix A: Glossary of Terms
802.1P
802.1Q
802.1X
ARP
CELP
CLAN
DHCP
Control LAN, type of Gatekeeper circuit pack.
Dynamic Host Configuration Protocol, an IETF protocol used to automate IP address allocation and management.
Differentiated Services, an IP-based QoS mechanism.
DiffServ
DNS
Domain Name System, an IETF standard for ASCII strings to represent IP addresses. The Domain Name System (DNS) is a distributed Internet directory service. DNS is used mostly to translate between domain names and IP addresses.
Avaya 1600 Series IP Deskphones can use DNS to resolve names into IP addresses. In DHCP, TFTP, and HTTP files, DNS names can be used wherever IP addresses were available as long as a valid DNS server is identified first.
Gatekeeper H.323 application that performs essential control, administrative, and managerial functions in the media server. Sometimes called CLAN in Avaya documents.
H.323
HTTP
HTTPS
IETF
A TCP/IP-based protocol for VoIP signaling.
Hypertext Transfer Protocol, used to request and transmit pages on the World Wide
Web.
A secure version of HTTP.
Internet Engineering Task Force, the organization that produces standards for communications on the internet.
LAN
LLDP
MAC
Media
Channel
Encryption
NAPT
802.1Q defines a layer 2 frame structure that supports VLAN identification and a QoS mechanism usually referred to as 802.1P.
Authentication method for a protocol requiring a network device to authenticate with a back-end Authentication Server before gaining network access. Applicable 1600
Series IP deskphones support IEEE 802.1X for pass-through and for Supplicant operation with the EAP-MD5 authentication method.
Address Resolution Protocol, used, for example, to verify that the IP address provided by the DHCP server is not in use by another IP deskphone.
Code-excited linear-predictive. Voice compression requiring only 16 kbps of bandwidth.
Local Area Network.
Link Layer Discovery Protocol. All IP deskphones with an Ethernet interface support the transmission and reception of LLDP frames on the Ethernet line interface in accordance with IEEE standard 802.1AB.
Media Access Control, ID of an endpoint.
Encryption of the audio information exchanged between the IP deskphone and the call server or far end deskphone.
Network Address Port Translation.
1 of 2
Issue 5 May 2014 117
Glossary of Terms
NAT
OPS
PHP
PSTN
QoS
RSVP
RTCP
RTP
SDP
Signaling
Channel
Encryption
SIP
SNTP
TCP/IP
TFTP
TLS
UDP
Unnamed
Registration
VLAN
VoIP
Network Address Translation.
Off-PBX Station.
Hypertext Preprocessor, software used to assist in the format and display of Web pages.
Public Switched Deskphone Network, the network used for traditional telephony.
Quality of Service, used to refer to several mechanisms intended to improve audio quality over packet-based networks.
Resource ReSerVation Protocol, used by hosts to request resource reservations throughout a network.
RTP Control Protocol, monitors quality of the RTP services and can provide real-time information to users of an RTP service.
Real-time Transport Protocol. Provides end-to-end services for real-time data such as voice over IP.
Session Description Protocol. A well-defined format for conveying sufficient information to discover and participate in a multimedia session.
Encryption of the signaling protocol exchanged between the IP deskphone and the call server. Signaling channel encryption provides additional security to the security provided by media channel encryption.
Session Initiation Protocol. An alternative to H.323 for VoIP signaling. This protocol is not applicable to 1600 Series IP Deskphones.
Simple Network Time Protocol. An adaptation of the Network Time Protocol used to synchronize computer clocks in the internet.
Transmission Control Protocol/Internet Protocol, a network-layer protocol used on
LANs and internets.
Trivial File Transfer Protocol, used to provide downloading of upgrade scripts and application files to certain IP deskphones.
Transport Layer Security, an enhancement of Secure Sockets Layer (SSL). TLS is compatible with SSL 3.0 and allows for privacy and data integrity between two communicating applications.
User Datagram Protocol, a connectionless transport-layer protocol.
Registration with Avaya Aura Communication Manager by an IP deskphone with no extension. Allows limited outgoing calling.
Virtual LAN.
Voice over IP, a class of technology for sending audio data and signaling over LANs.
2 of 2
118 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Appendix B: Related Documentation
IETF Documents
The following documents provide standards relevant to IP Telephony and are available for free from the IETF Web site: http://www.ietf.org/rfc.html
.
● Requirements for Internet Hosts - Communication Layers, October 1989, by R. Braden (STD 3: RFC 1122)
● Requirements for Internet Hosts - Application and Support, October 1989, by R. Braden (STD 3: RFC 1123)
● Internet Protocol (IP), September 1981, by Information Sciences Institute
(STD 5: RFC 791), as amended by Internet Standard Subnetting Procedure,
August 1985, by J. Mogul and J. Postel (STD 5: RFC 950)
● Broadcasting Internet Datagrams, October 1984, by J. Mogul (STD 5: RFC 919)
● Broadcasting Internet Datagrams in the Presence of Subnets, October 1984, by J. Mogul (STD 5: RFC 922)
● User Datagram Protocol (UDP), August 28, 1980, by J. Postel (STD 6: RFC 768)
● Transmission Control Protocol (TCP), September 1981, by Information Sciences
Institute (STD 7: RFC 793)
● Domain Names - Concepts and Facilities (DNS), November, 1987, by P. Mockapetris (STD 13: RFC 1034)
● Domain Names - Implementation and Specification (DNS), November 1987, by P. Mockapetris (STD 13: RFC 1035)
● An Ethernet Address Resolution Protocol (ARP), November 1982, by David C. Plummer (STD 37: RFC 826)
● Dynamic Host Configuration Protocol (DHCP), March 1997, by R. Droms (RFC 2131)
● DHCP Options and BOOTP Vendor Extensions, March 1997, by S. Alexander and R. Droms (RFC 2132)
● RTP: A Transport Protocol for Real-Time Applications (RTP/RTCP),
January 1996, by H. Schulzrinne, S. Casner, R. Frederick, V. Jacobson (RFC 1889)
● Definition of the Differentiated Services Field (DS Field) in the IPv4 and IPv6 Headers,
(DIFFSRV), December 1998, by K. Nichols, S. Blake, F. Baker and D. Black (RFC 2474)
Issue 5 May 2014 119
Related Documentation
● Management Information Base for Network Management of TCP/IP Internets: MIB-II, March 1991, edited by K. McCloghrie and M. Rose (RFC 1213)
● SNMPv2 Management Information Base for the Internet Protocol using SMIv2,
November 1996, edited by K. McCloghrie (RFC 2011)
● Structure of Management Information Version 2 (SMIv2), April 1999, edited by K. McCloghrie, D. Perkins, and J. Schoenwaelder (RFC 2578)
● Resource ReSerVation Protocol VI, September 1997, by R. Braden, L. Zhang, S. Berson, S.
Herzog, and S. Jamin (RFC 2205)
● The TLS Protocol Version 1.0, January 1999, by T. Dierks and C. Allen (RFC 2246)
ITU Documents
The following documents are available for a fee from the ITU Web site: http://www.itu.int
.
● Recommendation G.711, Pulse Code Modulation (PCM) of Voice Frequencies,
November 1988
● Recommendation G.722, 7 kHz Audio-Coding within 64 kbit/s, November 1988
● Recommendation G.729, Coding of speech at 8 kbit/s using Conjugate-Structure
Algebraic-Code-Excited Linear-Prediction (CS-ACELP), March 1996
● Annex A to Recommendation G.729: Reduced complexity 8 kbit/s CS-ACELP
speech codec, November 1996
● Annex B to Recommendation G.729: A silence compression scheme for G.729
optimized for terminals conforming to Recommendation V.70, November 1996
● Recommendation H.225.0, Call signalling protocols and media stream
packetization for packet-based multimedia communications systems, February 1998
● Recommendation H.245, Control protocol for multimedia communication,
February 1998
● Recommendation H.323, Packet-based multimedia communications systems,
February 1998
120 1600 Series IP Deskphone Administrator Guide Release 1.3.5
ISO/IEC, ANSI/IEEE Documents
The following documents are available for a fee from the ISO/IEC standards Web site: http:// www.iec.ch
.
● International Standard ISO/IEC 8802-2:1998 ANSI/IEEE Std 802.2, 1998 Edition, Information technology - Telecommunications and information exchange between systems - Local and
metropolitan area networks- Specific requirements- Part 2: Logical Link Control
● ISO/IEC 15802-3: 1998 ANSI/IEEE Std 802.1D, 1998 Edition, Information technology-
Telecommunications and information exchange between systems- Local and metropolitan area
networks- Common specifications- Part 3: Media Access Control (MAC) Bridges
● IEEE Std 802.1Q-1998, IEEE Standards for Local and Metropolitan Area Networks: Virtual
Bridged Local Area Networks
● IEEE Std 802.3af-2003, IEEE Standard for Information technology- Telecommunications and information exchange between systems- Local and metropolitan area networks- Specific requirements- Part 3: Carrier Sense Multiple Access with Collision Detection (CSMA/CD) Access
Method and Physical Layer Specifications- Amendment: Data Terminal Equipment (DTE) Power
via Media Dependent Interface (MDI)
● IEEE Std. 802.1X-2004, IEEE Standard for Local and Metropolitan Area Networks - Port-Based
Network Access Control. For more information about 802.1X, see: http://www.standards.ieee.org/getieee802/download/802.1X-2004.pdf
Issue 5 May 2014 121
Related Documentation
122 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Appendix C: Sample Administration Forms
Use the sample screens that follow as guidelines for deskphone setup.
Figure 1: Station Form - Basic Deskphone Information
Issue 5 May 2014 123
Sample Administration Forms
Figure 2: Station Form - Feature Options
124 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Figure 3: Station Form - IP Phone Group ID, Bridged Calls, and Enhanced Call Forwarding
Issue 5 May 2014 125
Sample Administration Forms
Figure 4: Station Form - Site Data, Abbreviated Dial, and Button Assignments
126 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Figure 5: Feature-Related System Parameters Form
Issue 5 May 2014 127
Sample Administration Forms
Figure 6: IP Address Mapping Form
128 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Figure 7: IP Codec Set Form
Issue 5 May 2014 129
Sample Administration Forms
Figure 8: Inter-Network Region Connection Management Form
The entries on the IP Address network map shown in
Figure 6 might redirect endpoints into a particular
network region. That region could be different from what is administered on the previous forms.
130 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Figure 9: IP Network Region Form
Issue 5 May 2014 131
Sample Administration Forms
Figure 10: IP-Options System Parameters Form
132 1600 Series IP Deskphone Administrator Guide Release 1.3.5
Index
Numerical
1600 Series IP Telephone
Restart . . . . . . . . . . . . . . . . . . . . .
1600 Series IP Telephones
Administering Options for . . . . . . . . . . . .
Administration Alternatives and Options . . . . . .
Customizable System Parameters . . . . . . . .
Customizing Applications and Options . . . . . .
Initialization Process . . . . . . . . . . . . . . .
Network Audio Quality Display . . . . . . . . . .
Scripts and Application Files . . . . . . . . . . .
1603/1603SW/1603-I IP Telephone . . . . . . . . .
1608/1608-I IP Telephone . . . . . . . . . . . . .
1616/1616-I IP Telephones . . . . . . . . . . . . .
802.1X
. . . . . . . . . . . . . . . . . . . . . .
A
About This Guide
ADDR Option
. . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . .
Ad-Hoc Conferences . . . . . . . . . . . . . . . .
Administering Applications and Options . . . . . . .
Administering Avaya Communication Manager . . . .
Administering Features . . . . . . . . . . . . . . .
Administering Telephone Options . . . . . . . . . .
Administration Alternatives and Options for 1600 Series IP Telephones
Administration Forms . . . . . . . . . . . . . . . .
Administration Forms, Samples . . . . . . . . . . .
Administration, for Avaya Communication Manager
Administration, for Telephones on media server
.
. . .
Administrative Checklist . . . . . . . . . . . . . .
Administrative Options, Local . . . . . . . . . . . .
Administrative Process, The . . . . . . . . . . . . .
Aliasing . . . . . . . . . . . . . . . . . . . . . .
Aliasing 1600 Series IP Telephones . . . . . . . . .
Alternatives, Administration . . . . . . . . . . . . . .
ANSI/IEEE Documents . . . . . . . . . . . . . . .
Application File and Upgrade Script, Choosing . . . .
Application Files and Telephone Software . . . . . .
Application Files, and Scripts for 1600 Series IP Telephones
Application Status Flag (APPSTAT) . . . . . . . . .
Application Status Flags and Their Meaning . . . . .
Applications and Options, Administering . . . . . . .
Applications, Customizing . . . . . . . . . . . . .
Application-specific parameters, administering . . . . .
APPSTAT . . . . . . . . . . . . . . . . . . . . .
Assessment, of Network . . . . . . . . . . . . . .
Auto Hold administration . . . . . . . . . . . . . .
Issue 5 May 2014 133
Index
Auto select any idle appearance administration . . .
B
Backup . . . . . . . . . . . . . . . . . . . . . .
Backup File Formats . . . . . . . . . . . . . . . .
Backup, Options and Non-Password Parameters Saved
Backup/Restore . . . . . . . . . . . . . . . . . .
Backup/Restore HTTP Configuration . . . . . . . .
button labels . . . . . . . . . . . . . . . . . . . .
C
Call Appearances and Feature Buttons . . . . . . .
Call Center Administration
Call Server Requirements
. . . . . . . . . . . . .
. . . . . . . . . . . . .
Call Transfer Considerations . . . . . . . . . . . .
Checklist, Administrative . . . . . . . . . . . . . .
Clear Procedure . . . . . . . . . . . . . . . . . .
Communication Manager Administration . . . . . . .
Conference/Transfer on Primary Appearance administration
Contents of the Settings File . . . . . . . . . . . .
Coverage Path administration . . . . . . . . . .
,
Customizable System Parameters . . . . . . . . .
Customizing 1600 Series IP Telephone Applications and Options
D
Debug Procedure . . . . . . . . . . . . . . . . .
DHCP and File Servers
DHCP Generic Setup
. . . . . . . . . . . . . .
. . . . . . . . . . . . . . .
DHCP options . . . . . . . . . . . . . . . . . . .
DHCP Server . . . . . . . . . . . . . . . . . . .
DHCP Server Administration . . . . . . . . . . . .
DHCP Server Setup . . . . . . . . . . . . . . . .
DHCP Server to Telephone initialization
DHCP Server, Windows 2000 Setup
. . . . . . .
. . . . . . . .
DHCP Server, Windows NT 4.0 Setup . . . . . . . .
DIFFSERV . . . . . . . . . . . . . . . . . . . .
Disable Event Logging . . . . . . . . . . . . . . .
DNS Addressing . . . . . . . . . . . . . . . . . .
Document Organization . . . . . . . . . . . . . . .
Documentation, Related . . . . . . . . . . . . .
E
Enable Event Logging . . . . . . . . . . . . . . .
Enhanced Conference Features administration . .
,
Enhanced Dialing Procedures
Enhanced Local Dialing
. . . . . . . . . . .
. . . . . . . . . . . . . .
Error Conditions . . . . . . . . . . . . . . . . . .
Event Logging . . . . . . . . . . . . . . . . . . .
134 1600 Series IP Deskphone Administrator Guide Release 1.3.5
F
Far End Mute administration . . . . . . . . . . . .
Feature Administration for Avaya Communication Manager
Feature Buttons and Call Appearances . . . . . . .
Feature-Related System Parameters Form . . . . .
Feature-Related System Parameters, administering on CM
Features, Administering . . . . . . . . . . . . . .
File download
Choosing the Right Application and Upgrade Script File 56
Download File Content . . . . . . . . . . . . .
from . . . . . . . . . . . . . . . . . . . . . . . .
G
General Download Process . . . . . . . . . . . . .
Generic Setup, for DHCP . . . . . . . . . . . . . .
Glossary of Terms . . . . . . . . . . . . . . . . .
Group Identifier . . . . . . . . . . . . . . . . . .
GROUP System Value . . . . . . . . . . . . . . .
H
Hardware Requirements . . . . . . . . . . . . . .
HTTP Configuration for Backup/Restore . . . . . . .
HTTP/HTTPS Server . . . . . . . . . . . . . . . .
I
IEC/ISO Documents . . . . . . . . . . . . . . . .
IEEE 802.1D and 802.1Q
. . . . . . . . . . . . .
,
IEEE 802.ID/Q QoS parameters
IEEE/ANSI Documents
. . . . . . . . . .
. . . . . . . . . . . . . . .
IETF Documents . . . . . . . . . . . . . . . . . .
Initialization and Address Resolution Diagram . . . .
Initialization Process, for 1600 Series IP Telephones . .
Installation, Network Information Required before installing 17
Interface Control . . . . . . . . . . . . . . . . . .
Interface, administering the . . . . . . . . . . . . . .
Inter-Network Region Connection Management Form
IP Address Lists and Station Number Portability . . .
IP Address Mapping Form . . . . . . . . . . . . .
IP Addresses, administering . . . . . . . . . . . . .
IP Codec Set Form . . . . . . . . . . . . . . . . .
IP Interface and Addresses, for media servers . . . .
IP-Options System Parameters Form . . . . . . . .
ISO/IEC, ANSI/IEEE Documents . . . . . . . . . .
ITU Documents . . . . . . . . . . . . . . . . . .
L
Language Selection . . . . . . . . . . . . . . . .
Link Layer Discovery Protocol (LLDP) . . . . . . . .
Issue 5 May 2014 135
Index
LLDP Data Units Transmitted . . . . . . . . . . . .
Local Administrative Options . . . . . . . . . . . .
LOG Procedure . . . . . . . . . . . . . . . . . .
Logoff Procedure . . . . . . . . . . . . . . . . .
M
Media Server (Switch) Administration . . . . . . . .
Media Server Administration, Other Considerations .
Media Server Field Names and Corresponding Script File Parameter Names
N
NAT . . . . . . . . . . . . . . . . . . . . . . . .
Network Assessment . . . . . . . . . . . . . . . .
Network Audio Quality Display . . . . . . . . . . .
Network Audio Quality Display on 1600 Series IP Deskphones on page 16 19
Network Considerations, Other . . . . . . . . . . .
Network Information, Required . . . . . . . . . . .
Network Region Form . . . . . . . . . . . . . . .
Network Requirements . . . . . . . . . . . . . . .
O
On-Hook Dialing administration . . . . . . . . . . .
Options and Applications, Administering . . . . . . .
Options, Administering . . . . . . . . . . . . . . .
Options, Customizing . . . . . . . . . . . . . . .
Options, entering using the Telephone Dialpad . . .
Options, for 1600 Series IP Telephone Administration .
Other Considerations, for media server administration
Other Network Considerations . . . . . . . . . . .
P
Parameter Data Precedence . . . . . . . . . . . . .
Parameter Values . . . . . . . . . . . . . . . . .
Parameters in Real-Time . . . . . . . . . . . . . .
Parameters Saved During Backup
Parameters, Customizable
. . . . . . . . .
. . . . . . . . . . .
Pass-Through and Proxy Logoff, 802.1X
. . . . . .
Port Utilization
Selection . . . . . . . . . . . . . . . . . . . .
TCP/UDP . . . . . . . . . . . . . . . . . . .
Proxy Logoff and Pass-Through, 802.1X
. . . . . .
Q
QoS . . . . . . . . . . . . . . . . . . . . . . .
,
Administrative Parameters . . . . . . . . . . . .
IEEE 802.1D and 802.1Q
. . . . . . . . . . . .
136 1600 Series IP Deskphone Administrator Guide Release 1.3.5
R
Registration and Authentication . . . . . . . . . . .
Related Documentation . . . . . . . . . . . . . .
Reliability and Performance . . . . . . . . . . . . .
Requirements . . . . . . . . . . . . . . . . . . . .
Call Server . . . . . . . . . . . . . . . . . . .
Hardware
Network
. . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . .
Server . . . . . . . . . . . . . . . . . . . . .
Reset System Values . . . . . . . . . . . . . . .
Restore . . . . . . . . . . . . . . . . . . . . . .
Restore/Backup . . . . . . . . . . . . . . . . . .
Restrict Last Call Appearance administration
RSVP and RTCP
. . . .
. . . . . . . . . . . . . . . . .
RTCP and RSVP . . . . . . . . . . . . . . . . .
S
Sample Administration Forms . . . . . . . . . . . .
Script File Parameter Names and Corresponding Media Server Field Names
Scripts and Application Files, for 1600 Series IP Telephones
Security . . . . . . . . . . . . . . . . . . . . . .
Send All Calls (SAC) administration
Server Administration
. . . . . . . . .
. . . . . . . . . . . . . . .
Server Administration, DHCP . . . . . . . . . . . .
Server Requirements . . . . . . . . . . . . . . . .
Settings File . . . . . . . . . . . . . . . . . . . .
Settings File, Contents . . . . . . . . . . . . . . .
SNMP . . . . . . . . . . . . . . . . . . . . . . .
Software . . . . . . . . . . . . . . . . . . . . .
Software Checklist . . . . . . . . . . . . . . . . .
Software, Telephone . . . . . . . . . . . . . . . .
Static Addressing
Installation . . . . . . . . . . . . . . . . . . .
Station Form
Basic Telephone Information . . . . . . . . . .
Feature Options . . . . . . . . . . . . . . . .
IP Phone Group ID, Bridged Calls & Enhanced Call Forwarding
Site Data, Abbreviated Dialing, & Button Assignments
Station Form - Basic Telephone Information . . . . .
Station Form - Feature Options . . . . . . . . . . .
Station Form Administration Results Chart . . . . . .
Station Number Portability and IP Address Lists . . .
Supplicant Operation, 802.1X
. . . . . . . . . . . .
Switch Administration . . . . . . . . . . . . . . .
Switch Compatibility and Aliasing IP Telephones . . .
System Parameter Values, Impact of Received TLVs .
System Parameter Values, troubleshooting . . . . .
System Parameters . . . . . . . . . . . . . . . .
System Parameters, Customizable . . . . . . .
System Values, Reset . . . . . . . . . . . . . . .
Issue 5 May 2014 137
Index
T
Tagging and VLAN, administering . . . . . . . . . . .
TCP/UDP Port Utilization . . . . . . . . . . . . . .
Telephone Administration . . . . . . . . . . . .
,
Telephone and Call Server initialization . . . . . . .
Telephone and File Server initialization . . . . . . .
Telephone Initialization Process . . . . . . . . . . .
Telephone Software and Application Files . . . . . .
Telephone to Network initialization . . . . . . . . . .
Terms, Glossary of . . . . . . . . . . . . . . . . .
TEST Procedure . . . . . . . . . . . . . . . . . .
TLVs Received, Impact on System Parameter Values
Troubleshooting
Parameter Values . . . . . . . . . . . . . . .
VIEW Administrative Option . . . . . . . . . . .
U
UDP Port Selection . . . . . . . . . . . . . . . .
UDP/TCP Port Utilization . . . . . . . . . . . . . .
Unnamed Registration . . . . . . . . . . . . . . .
Upgrade Script and Application File, Choosing the Right 56
Upgrade Script File . . . . . . . . . . . . . . . .
Upgrade Script, contents of . . . . . . . . . . . . .
V
VIEW Administrative Option
VLAN Considerations
. . . . . . . . . . . .
. . . . . . . . . . . . . . .
VLAN Default Value
VLAN Separation
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
VLAN Separation Rules . . . . . . . . . . . . . .
VLAN tagging . . . . . . . . . . . . . . . . . . .
Voice Mail Integration . . . . . . . . . . . . . . .
W
Web Configuration Tool . . . . . . . . . . . . . .
138 1600 Series IP Deskphone Administrator Guide Release 1.3.5
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 1 Avaya 1600 Series IP Deskphones
- 3 Contents
- 7 Chapter 1: Introduction
- 7 About This Guide
- 7 New in this release
- 8 Document Organization
- 9 Other Documentation
- 11 Chapter 2: Administration Overview and Requirements
- 11 1600 Series IP Deskphones
- 15 Parameter Data Precedence
- 15 The Administrative Process
- 16 Administrative Checklist
- 17 Deskphone Initialization Process
- 17 Step 1: Deskphone to Network
- 18 Step 2: DHCP Server to Deskphone
- 18 Step 3: Deskphone and File Server
- 18 Step 4: Deskphone and the Call Server
- 19 Error Conditions
- 21 Chapter 3: Network Requirements
- 21 Network Assessment
- 21 Hardware Requirements
- 22 Server Requirements
- 22 DHCP Server
- 22 HTTP/HTTPS Server
- 23 Required Network Information
- 24 Other Network Considerations
- 24 SNMP
- 25 Reliability and Performance
- 25 QoS
- 25 IEEE 802.1P and 802.1Q
- 26 Network Audio Quality Display on 1600 Series IP Deskphones
- 26 IP Address Lists and Station Number Portability
- 27 TCP/UDP Port Utilization
- 30 Security
- 30 Registration and Authentication
- 31 Chapter 4: Avaya Aura Communication Manager Administration
- 31 Call Server Requirements
- 31 Switch Compatibility and Aliasing IP Deskphones
- 33 Media Server (Switch) Administration
- 33 IP Interface and Addresses
- 34 UDP Port Selection
- 34 RSVP and RTCP
- 34 QoS
- 34 IEEE 802.1P and 802.1Q
- 35 NAT
- 35 DIFFSERV
- 36 Voice Mail Integration
- 36 1600 Series IP Deskphones with Avaya Aura Communication Manager 5.2 Native Support
- 36 1600 Series IP Deskphones Aliased as 4600 Series IP Deskphones
- 37 Deskphone Administration
- 37 System-Wide Administration
- 37 Feature-Related System Parameters
- 38 Administering Stations
- 39 Aliasing 1600 Series IP Deskphones
- 39 Administering Features
- 40 Feature Buttons and Call Appearances
- 40 For the 1603/1603SW/1603-I/1603SW-I and 1608/1608-I IP Deskphones
- 40 For the 1616/1616-I IP Deskphones
- 41 Conference Details Screen for Ad-Hoc Conferences
- 41 Shuffling
- 42 Printing Button Labels
- 43 Chapter 5: Server Administration
- 43 Software Checklist
- 43 DHCP and File Servers
- 44 DHCP Server Administration
- 44 DHCP Generic Setup
- 48 Windows NT 4.0 DHCP Server
- 48 Verifying the Installation of the DHCP Server
- 49 Creating a DHCP Scope for the IP Deskphones
- 50 Editing Custom Options
- 50 Adding the DHCP Option
- 51 Activating the Leases
- 51 Verifying Your Configuration
- 52 Windows 2000 DHCP Server
- 52 Verifying the Installation of the DHCP Server
- 54 Adding DHCP Options
- 55 Activating the New Scope
- 55 HTTP Generic Setup
- 56 HTTP Configuration for Backup/Restore
- 56 For IIS Web Servers
- 58 Web Configuration Tool
- 61 Chapter 6: Deskphone Software and Application Files
- 61 General Download Process
- 61 Software
- 62 1600 Series IP Deskphone Scripts and Application Files
- 62 Choosing the Right Application File and Upgrade Script File
- 62 Upgrade Script File
- 63 Settings File
- 64 Contents of the Settings File
- 65 The GROUP System Value
- 65 Call Center Administration
- 71 Chapter 7: Administering Deskphone Options
- 71 Administering Options for the 1600 Series IP Deskphones
- 78 VLAN Considerations
- 78 VLAN Tagging
- 78 VLAN Default Value and Priority Tagging
- 79 VLAN Separation
- 81 DNS Addressing
- 81 IEEE 802.1X
- 82 802.1X Pass-Through and Proxy Logoff
- 82 802.1X Supplicant Operation
- 84 Link Layer Discovery Protocol (LLDP)
- 89 Local Administrative Options Using the Deskphone Dialpad
- 89 Clear Procedure
- 90 Disabling or enabling the Debug mode
- 91 Group Identifier
- 92 Reset System Values
- 94 Restart the Deskphone
- 95 Interface Control
- 97 The View Local Procedure
- 100 Static Addressing Installation
- 103 Disable/Enable Event Logging
- 104 Logoff
- 105 Self-Test Procedure
- 107 Language Selection
- 107 1600 Series Global Deskphones
- 109 1600 Series International Deskphones
- 112 Enhanced Local Dialing
- 113 Backup/Restore
- 114 Backup
- 115 Restore
- 117 Chapter 8: Administering Applications and Options
- 117 Customizing 1600 Series IP Deskphone Applications and Options
- 120 The Application Status Flag (APPSTAT)
- 123 Appendix A: Glossary of Terms
- 125 Appendix B: Related Documentation
- 125 IETF Documents
- 126 ITU Documents
- 127 ISO/IEC, ANSI/IEEE Documents
- 129 Appendix C: Sample Administration Forms
- 139 Index
- 139 Numerical
- 139 A
- 140 B
- 140 C
- 140 D
- 140 E
- 141 F
- 141 G
- 141 H
- 141 I
- 141 L
- 142 M
- 142 N
- 142 O
- 142 P
- 142 Q
- 143 R
- 143 S
- 144 T
- 144 U
- 144 V
- 144 W