PLASMA DISPLAY

USER’S MANUAL

DT-42A1

Helpline Number : 0870 100 2525

Proper use guarantees product life.

Before using the product, be advised that you read this owner’s manual well and try to operate it.

• 42” VGA wide Plasma Panel

• Built in 2-Analog Tuners

This PDP has 2-analog tuners inside for watching terrestrial broadcasting without the need to purchase a separate broadcasting receiver.

• Support Picture-in-Picture (PIP)

• DVD Direct Connection / Outstanding Picture Quality via a Digital

Broadcast Receiver

DVD can be directly connected to the unit so that you can view clear digital images. You can enjoy even higher quality images by connecting a digital broadcasting receiver with which digital broadcasts can be viewed.

• PC Direct Connection

PC can be connected to the PDP without a separate device and can be used as a monitor making it ideal for presentation, various events and exhibitions.

• 160˚ Wide-Angle Viewing Area

• Flat Panel with No Distortion and Colour Blurring

Since Plasma TV has no problems such as distortion, blurring, flickering unlike existing CRT type displays you can enjoy Home Cinema picture quality and sound.

• Various Video Control

- 17 Languages OSD - Full-screen still function

- Various aspect ratio (16:9, 4:3, Panorama, LB(16:9), LBS(16:9), 14:9, LB(14:9), LBS(14:9), Auto)

• Free Volt (100-240V~, 50/60Hz)

• DVI (Digital Visual Interface) Connection

Using the DVI Input, you can receive directly a digital signal from the computer. Consequently, pictures on the screen are much more clear and fresh.

• MGDI (Meta Genuine Digital Image) Engine

MGDI is the image enhancement technology designed by Daewoo Electronics, which provides more clear, realistic, and delicate images.

This Owner’s Manual presents safety precautions and how to use the product.

After reading it thoroughly, use the product safely.

Keep this manual where the user can see it easily.

Failure to comply with warnings and cautions for the safe use of electric appliances may cause fire or human injury.

DISPOSAL OF USED ELECTRICAL & ELECTRONIC EQUIPMENT

The meaning of the symbol on the product, its accessory or packaging indicates that this product shall not be treated as household waste. Please, dispose of this equipment at your applicable collection point for the recycling of electrical & electronic equipments waste. In the European Union and Other European countries which there are separate collection systems for used electrical and electronic product. By ensuring the correct disposal of this product, you will help prevent potentially hazardous to the environment and to human health, which could otherwise be caused by unsuitable waste handling of this product.

The recycling of materials will help conserve natural resources. Please do not therefore dispose of your old electrical and electronic equipment with your household waste. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

4

Always obey all safety messages.

• All the safety and operating instructions should be read before the product is operated.

If anything strange happens, unplug this product from the wall outlet.

• Do not disassemble or replace any parts of the TV.

Refer to a qualified service personnel for repair.

WARNING

You can be Killed or seriously injured if you do not follow these instructions.

Power

During a lightning storm, or when it is left unattended and unused for a long period of time, unplug it from the wall outlet.

It can result in fire.

When unplugging your TV, always grip the plug firmly and pull straight out from the socket.

It can result in fire or electric shock due to damaged power cord.

This product must be properly grounded.

• Improper grounding may cause malfunction or electric shock.

• When proper grounding is not possible, install circuit breaker.

• Do not ground to gas pipe, water pipe, lightning rod, or telephone line.

During a lightning storm, unplug the

TV from the wall outlet, and do not touch the antenna.

It can cause fire or electric shock.

Installation

Do not use this product in the neighborhood of a bath or shower.

It can result in electric shock or fire.

Do not place this TV on an unstable cart, stand, or table

It may cause the product and cart to overturn, damaging equipment or causing possible injury.

During Use

Do not open the cover (or back) because high voltage is present within the TV enclosure.

It may cause electric shock.

Never push any kind of objects into this product through openings at the back of TV.

It may cause fire or electric shock.

The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

Spilled liquids may cause electric shock or fire.

Do not allow children to play or hang on the TV.

These actions may tip it over, causing personal injury.

Do not place a candle or lighted cigarette on the TV.

If these fall into the inside of the tv, it may cause a fire or explosion.

Do not disassemble batteries, and do not leave around in case children swallow them.

Heavy metal may contaminate environment, and can be harmful or detrimental to human health. (If children swallow the batteries, go to hospital and consult with a doctor.)

Batteries could explode if fitted incorrectly. Align the batteries according to the (+) and (-) indication inside the case.

Do not spray water onto the TV or wipe with damp cloth.

It may cause an electric shock or fire.

Unplug the TV from the wall outlet when smoke or a strange smell occurs, then refer to a service personnel.

Leaving the TV on in this condition, may cause fire or electric shock.

5

6

Always obey all safety messages.

• All the safety and operating instructions should be read before the product is operated.

Power

When moving your TV, remove the power plug, antenna, and cables, and be sure to move it by using two people..

Failure to follow this instruction can result in electric shock or personal injury.

Do not touch the power plug with wet hands when plugging or unplugging it into the wall socket.

It can result in a risk of electric shock.

CAUTION

You can be injured, or this product or any other of your property can be damaged if you don’t follow instructions.

Installation

Do not install the product where there is oil, smog, moist, or dust

It may cause malfunction.

Do not install the product where it will be exposed to the direct sunlight, and the product should not be near heat sources such as radiators, stoves, etc.

It may cause malfunction.

For proper ventilation, separate the product from the wall, and keep a distance of more than 10cm (4inches).

Due to the increase of temperature inside the TV, it may cause fire.

Minimum distances around the apparatus for sufficient ventilation.

Due to the increase of temperature inside the TV, it may cause a fire.

If you wish to install this product on the wall or ceiling, refer to a professional.

Failure to do so may cause damage to product and injury to human.

When using an outside antenna system, do not install it in the vicinity of overhead power lines.

If the antenna touches such power lines, it may cause electric shock.

During Use

Do not wipe the TV using a cloth damped with chemicals (benzene, thinners, etc.).

The TV appearance may be marred.

(Unplug the power plug and wipe with soft cloth.)

Do not place heavy objects or heat sources on the power cord.

It may damage the power cord, causing fire or electric shock.

The plasma display panel consists of fine cells. Although the panels are produced with more than 99.9

percent active cells, there may be some cells that do not produce light or remain lit.

Do not allow a still picture to be displayed for an extended period, as this can cause a permanent ghost image to remain on the Plasma

Display.

Examples of still pictures include logos, video games, computer images, teletext and images displayed in 4:3 mode.

Do not place any object or cover on the TV.

In an event of improper ventilation, the

TV will be overheated causing fire.

When watching the TV, the distance between the TV screen and your eye should be 5~7 times the diagonal size of the TV.

Watching the TV for a long time may hurt your eye sight.

The warranty does not cover any damage caused by image retention.

When cleaning of the inside of the

TV is required, consult A qualified service personnel.

When the TV is not cleaned for a long period of time, dust in it may cause fire or malfunction.

When the TV is placed on a cart or table, the front side of the TV should not project outward.

Unbalance may cause the TV to drop, resulting in personal injury or equipment malfunction and damage.

Do not grip speakers when moving the TV attached with speakers.

When moving the TV while gripping speakers, the speakers may fall from the

TV due to its weight, causing personal injury.

7

8

Note

Check to be sure that the following items are packed with your Plasma panel.

Supplied Accessories

Remote Control 1 UNIT

Ferrite Core 1UNIT

AC Cable 1 UNIT

For Scart

(1 unit)

Optional Accessories

Note

The following items are optional accessories.

Refer purchasing optional accessories from

Daewoo Electronics Local Retailers or the retailer from where you purchased the unit.

Table Top Stand

Wall Mounting Unit

9

PREPARATION

4 • Safety

8 • Checking Accessories

12 • Panel Controls

CONNECTION

15 • Antenna Connection

18 • To Watch TV

20 • Install Program

26 • Watching Digital Broadcasts

28 • Watching Cable Broadcasts

30 • Watching Satellite Broadcasts

32 • Watching a DVD Image

34 • Watching a VCR Image

36 • Watching a Camcorder/Game Console Image

38 • Connecting PC(15Pin D-Sub)

APPLICATION

44 • Selecting Picture Mode

45 • Customising Picture

50 • Watching a Still Image

53 • Adjusting Auto Sound Mode

58 • Checking the Current Input Signal

59 • MENU Background, Language and Child Lock Setting

61 • MGDI (Meta Genuine Digital Image)

65 • Image Sticking Minimisation (ISM)

70 • Teletext

MISC.

73 • Specifications

11

Front Panel, Rear Panel

* Items having the same names on the plasma display and the remote control would function in exactly the same way.

Front / Side

AV3

ON/OFF STAND-BY/OPERATE

• Power button

• Power Standby:

Red - Standby

Green - ON

• Power control sensor

INPUT SELECT

MENU

+

VOLUME

-

+

MOVE / PR

-

Pozycja obejm przeciwzakłóceniowych

Select when adjusting volume or select/adjust “MENU.”

Press when moving “MENU” or

“Program”.

12

Rear

DVI-D INPUT

DVI-D

INPUT

PC INPUT

(15 pin D-sub)

COMPONENT A/V jacks

(DTV/DVD INPUT jacks)

AV1 AV2

SCART, A/V

INPUT/OUTPUT,

Cable Receiver

INPUT/OUTPUT jacks

ANT

ANT Used when manufacturing

(or manufacturer use only)

Power

13

Remote Control

* The number in ( ) indicates the page in which the function of each button is explained in detail.

TV/VCR/DVD/SAT/CATV

19

Channel Number (0-9)

Use to select channel directly (0-9).

58 RECALL

Indicates the current state and resolution.

TV

Press to select TV Mode.

COMPONENT, PC/DVI

Press to select COMPONENT or PC/DVI modes.

20

Menu button

Used to display a main menu.

Previous Program button

It returns to previous channel.

Mute button

Mute sound.

43 Picture Mode button

Whenever pressing the button, it cycles in the following order: Normal - Dynamic - Cinema - User

53

Sound Mode button

Whenever pressing the button, it cycles in the following order: Normal - Movie - Music - News - User

55 Sound Effect button

Press to use a spatial sound effect

When using remote control:

• Be sure not to allow the remote control to drop or to become wet.

• Keep it away from hot or moist locations.

Note

• Use two “AAA” batteries.

• Be sure to use replacement batteries of the same type as the original ones.

• The life of a battery depends on how much it has been used.

Power button 19

Pressing the power button of the TV allows the display to be put in standby. (A red light is shown in the remote control sensor.) At this time, if you press the power button of the remote control, the display is turned ON (And shows a green light in the sensor).

Still

50

Used to view a still picture whilst watching moving images.(Sound can be heard.)

AV

Press to selet AV modes.

It changes in the following sequence

AV1 ->AV2 ->AV3

PR button ▲/▼: Adjusts the channel.

Volume button ◄/► : Adjusts the volume.

Screen Size button 46

Adjusts the size of the screen

(16:9, 4:3, Panorama etc.)

Sleep Timer

69

Each time you press this button, a different input mode appears. The sequence is as follows:

15Min. -> 30Min. - > 60Min. -> 90Min. -> 120Min. -> OFF

After the time is selected, the TV automatically goes into a stand-by state.

Teletext Function 70

I – II

- Selects the language during dual language broadcast.

- Selects mono sound during stereo broadcast.

51 PIP Mode Function

VIDEO/DVD Function

Installing the batteries in your remote control:

• Push to open the cover of the remote control

• Put the batteries in the battery cell after checking the polarities, and then shut the cover.

14

Remote Control supporting the multi brand devices.

- The remote control provided is designed to operate the Daewoo PDP set.

- However, using the remote control, you can control the Cable Converter, VCR , DVD and Satellite Broadcasting

Receiver of other brands after setting up the remote control.

Notices:

- All the preset codes are erased when replacing the battery. In this case, you must set the remote control again.

- Some of the products may not be applied because of different signal system.

- This is only for the basic control of the devices.

HOW TO SET UP THE REMOTE CONTROL FOR USING OTHER DEVICES .

• Turn on the device. (Cable Converter, VCR , DVD or Satellite Broadcasting Receiver)

• Press the device selection button of remote control until it is flickering. It takes about 3 seconds.

• Press the assigned three digits code of the device using number key button of the remote control toward the IR receiver of the device. The code number is provided below. Whenever pressing the number, the device selection button will be flicked once.

• If the code is set properly, the device will turn off automatically. If not, repeat the process 3.

• As the device is turned off, press the flickering device selection button of the remote control once.

Then the lamp of the button will be turned off.

• Now, the setting-up of the device can be controlled by Daewoo PDP remote control.

VCR (STANDARD: 002)

Maker (Brand) Name

DAEWOO

JVC

MITSUBISHI

PANASONIC

PHILIPS

SAMSUNG

SHARP

SONY

DVD

DAEWOO

LG

PANASONIC

PHILIPS

SAMSUNG

Remote Control Setup Code

Code Number (3 digit) List

SAT (STANDARD: 002)

Maker (Brand) Name

002 008 060 062 063

067 068

003 006 009 043 044

046 084 089

111 114 124

046 052 075 122

016 070 087 088 106

005 040 042 045 048

049 053 064

078 081 090 108

041 055 056 059 061

065 066 091 095

048 049 057 074

047 050 051 076 080

DAEWOO

PHILIPS

SAMSUNG

152 160

150 168 169

157 170

155

151 163 16

Code Number (3 digit) List

002

018 031 032

079

15

TV antenna installation may be found in most.

When a coaxial cable is used

Plug the coaxial cable to the antenna socket, and fix it firmly.

Antenna socket on the wall

Coaxial cable

Antenna socket at the back of the

PDP unit.

ANT/KABEL1

When a feeder cable is used

Antenna socket on the wall

Antenna socket at the back of the

PDP unit.

ANT/KABEL 1

Feeder cable connection with the combining adapter

16

Outdoor Antenna Connection

Outdoor antenna connection-such as VHF or/and UHF-may be necessary for installation at private houses.

Single Antenna Connection.

UHF Antenna

VHF Antenna

ANT/KABEL 1

Separate Antenna Connection.

VHF-Antenna

In case of coaxial cable

In case of feeder cable

UHF-Antenna ANT/KABEL 1

Antenna combining adapter

(separate purchase)

17

To Watch TV

- The buttons on the keypad in the PDP unit, which have the same name as those on the remote control, perform the same function as the remote control.

Press the “ON/OFF” button of the PDP unit.

• The „ PR ” or power button of the remote control and the keypad on the

PDP unit would be operated only when the „AC Power” of the PDP unit is supplied.

Otherwise, neither the remote control nor keypad of the PDP unit can turn on the

PDP.

When pressing the program button

• Select two digits if using the number button for Program selection.

For example, to watch Program No.9, press the number buttons 0 and 9. If pressing only number 9, it takes more time than pressing two digits for selecting a channel.

To mute the sound

1. Press the „ ” button.

2. No sound is heard if “MUTE” is displayed on the screen.

3. Sound is heard again if pressing the „ ”.

button once again. For example, you can use this button when telephone rings or when guest comes while watching TV.

Check of TV operation status

• If pressing the “RECALL” button, the status of the program or broadcasting being currently watched or entry status of video component is displayed on the screen.

Auto Power Off

• If TV broadcast for the day is finished, the TV will automatically turn off after about 30 minutes. However, if the Offtimer or Sleep timer is operating, it takes precedence. This auto power off feature only operates in the TV mode.

18

1 Press the “ON/OFF” button.

• Press the “ON/OFF” button of the

PDP unit.

• The LED of the PDP unit turns red colour.

• Press the “ PR ”, power button of the remote control, or any button on the keypad of the PDP unit.

• The LED of the PDP unit turns “green” colour and the TV turns on.

• To watch analog TV broadcasts, select the correct input, i.e. ‚PR’ in the on screen display box.

2 Select Program.

• Select the desired program by pressing the „ PR ” ,button or the number button.

Ex) Program 09

3

V

O

L

Adjust Volume.

PR

MENU

SC

RE

EN

S

IZ

E

V

O

L

• Sound reduces if pressing the

“ VOL” button.

• Sound increases if pressing the

“ VOL” button.

P

R

E

V

PR

PR

Volume 10

4 Press the “Power” Button to Turn the TV off.

• TV turns off and the LED of the PDP unit changes to red colour.

PR 09 _ _ _ _

MONO PM 12 : 00

19

Auto Setup

- This is the function for the TV to memorize the broadcasting channels. If the Auto Setup is done, you can simply find programs with “ PR ” buttons and so need not select programs by pressing each program number.

- Up to 100 TV stations can be stored in this set by programme numbers (0 to 99). Once you have preset the stations, you will be able to use the “ PR ” button or Number buttons to scan the stations you programmed.

Stations can be tuned using “Auto Setup” or “Manual Setup”.

20

1 Press the “Menu” Button.

• The menu screen appears as follows.

• Press the “ PR ” button and select

“Install”.

2

V

O

L

P

R

E

V

PR

Press the “◄ VOL ►” Button.

PR

MENU

SC

RE

EN

S

IZ

E

V

O

L

PR

Picture

Sound

Screen

Feature

Mode Normal

Brightness 32

Contrast 48

Sharpness 32

Color 32

Colour Temp. Normal

N.R. On

CTI On

Install

Move Select Exit

Picture

Sound

Screen

Auto Setup

Edit

Manual Setup

Feature

Install

Move Select Exit

3

V

O

L

Select the “Auto Setup”.

PR

• Select the “Auto Setup” with the

“ PR ” button.

• Then press the “ VOL ” button.

P

R

E

V

PR

MENU

PR

SC

RE

EN

S

IZ

E

V

O

L

Picture

Sound

Screen

Auto Setup

Edit

Manual Setup

Feature

Install

Move Select

4 Select the “Country”.

V

O

L

P

R

E

V

PR

PR

MENU

SC

RE

EN

S

IZ

E

V

O

L

PR

• There are 18 countries for selection. Choose the desired country before starting the search.

• If there is no proper country, select the “Others”.

Exit

Picture

Sound

Screen

Auto Setup

Country PL

Search

Feature

Install

Move Adjust Exit

5

V

O

L

Select the “Search”.

P

R

E

V

PR

PR

MENU

PR

SC

RE

EN

S

IZ

E

V

O

L

• Press the “VOL ” key to start searching.

• Then it automatically searches channels as on the right.

• While searching, if you press the

“Menu” button, the automatic channel search is stopped. But, channels searched by that time are saved.

Auto Searching ...

0 Channels Found...

Exit

6 Auto Search is completed.

V

O

L

P

R

E

V

PR

PR

MENU

SC

RE

EN

S

IZ

E

V

O

L

PR

• Edit menu appears as on the right if the search is completed.

• Refer to “Edit” on the following pages.

• The order of stored program may differ among countries.

Edit

PR CH Name Skip

PR98 S41 _ _ _ _ o

PR99 S41 _ _ _ _

PR0 C69 _ _ _ _ o

PR1 S41 _ _ _ _

PR2 S41 _ _ _ _

PR3 S41 _ _ _ _

PR4 S41 _ _ _ _ o o o o

Adjust

Move Delete

Exit

Skip

21

22

1 Deleting the Program.

• Place the selection bar on the program that you want to delete using the “ PR ” and “ VOL ” buttons.

• Press the Delete(Yellow) button.

• The deleted program goes to PR number 99 for recover.

Edit

PR CH Name Skip

PR98 S41 _ _ _ _ o

PR99 S41 _ _ _ _

PR0 C69 _ _ _ _ o

PR1 S41 _ _ _ _

PR2 S41 _ _ _ _

PR3 S41 _ _ _ _

PR4 S41 _ _ _ _ o o o o

Adjust

Move Delete

Exit

Skip

2 Moving the Program Positions

• Place the selection bar on the program that you want to move.

• Press the Move(Green) button.

• It becomes ready for moving as the colour of selection changes to green.

• Move the program that you desire to move to the wanted PR number.

• Press the Move(Green) button again to finish. The colour of selection changes to yellow.

3 Skipping the Channels

• Using “ PR ” and “ VOL ” buttons, place the selection bar on the program that you want to skip.

• Press the Skip(red) button.

• The colour of the program changes to red.

• The program will be skipped.

• In order to cancel skip state,press the Skip(red) button again.

1 Press the Number Buttons(0~9) or the “ VOL ”

Button to Select a Program Number You Want.

Picture

Sound

Screen

Feature

Install

0~9

Move

Adjust

Manual Setup

Program 01

Channel C06

Fine Tune 48

Name – – – – –

Video PAL

Audio D/K

Search

Memory

Adjust Exit

3

2 Find the Desired Channel.

V

O

L

P

R

E

V

PR

PR

MENU

PR

SC

RE

EN

S

IZ

E

V

O

L

• Using “ VOL ” button or number keys, select the desired channel directly, if you know it otherwise step through the numbers using the “VOL ” button until you find the right channel.

• By pressing red teletext button, you can toggle C channel to S-channel.

Picture

Sound

Screen

Feature

Install

0~9

Move

Adjust

Manual Setup

Program 01

Channel C06

Fine Tune 48

Name – – – – –

Video PAL

Audio D/K

Search

Memory

Adjust

Cable/Air

Exit

Fine Tune

• If you are unable to get a good picture or sound because of a poor signal reception, it is possible to adjust it with the Fine Tune feature.

• Move the selection bar to Fine Tune and press the “ VOL ” buttons to activate Fine

Tune up or down.

• Note that it operates while the “ VOL ” button is being pressed.

• It will be saved only when you select “OK” in

Memory.

Picture

Sound

Screen

Feature

Install

0~9

Move

Adjust

Manual Setup

Program 01

Channel C06

Fine Tune 48

Name – – – – –

Video PAL

Audio D/K

Search

Memory

Adjust

Cable/Air

Exit

23

24

4

V

O

L

Name the program

PR

MENU

SC

RE

EN

S

IZ

E

V

O

L

• Using ” VOL ” button, move the position where you want to write the character.

• Select the desired character with the “PR” button.

• There are A-Z, +, ., /, and 0-9 characters.

• After naming, you can exit by pressing the

”Menu” button.

P

R

E

V

PR

PR

Picture

Sound

Screen

Feature

Install

0~9

Move

Adjust

Manual Setup

Program 01

Channel C06

Fine Tune 48

Name C06

Video PAL

Audio D/K

Search

Memory

Adjust

Cable/Air

Exit

5 Select the Video and Audio System.

PR

• You can select the Video (PAL,SECAM,

SECAM-L) and Audio (B/G, DK, I, L)

System with these functions.

V

O

L

P

R

E

V

PR

MENU

SC

RE

EN

S

IZ

E

V

O

L

PR

Picture

Dźwiek

Screen

Feature

Install

Move

Manual Setup

Program 01

Channel C06

Fine Tune 48

Name C06

Video PAL

Audio D/K

Search

Memory

Select Exit

Picture

Dźwiek

Screen

Feature

Install

Move

Manual Setup

Program 01

Channel C06

Fine Tune 48

Name C06

Video PAL

Audio D/K

Search

Memory

Select Exit

6 Find the Desired Channel with ‘Search’.

V

O

L

P

R

E

V

PR

PR

MENU

SC

RE

EN

S

IZ

E

V

O

L

PR

• By selecting the Search function, you can find the desired channel, but it searches only one channel unlike Auto

Setup.

• If the nearest channel is found, the searching would be stopped automatically.

Picture

Dźwiek

Screen

Feature

Install

Move

Manual Setup

Program 01

Channel C06

Fine Tune 48

Name C06

Video PAL

Audio D/K

Search

Memory

Select Exit

7 Memorize the Program.

PR

• Without Memorizing, the program will not be saved.

• Press “ VOL ” buttons to memorize the program after selecting ‘Memory’. “OK” will flash green.

V

O

L

P

R

E

V

PR

MENU

PR

SC

RE

EN

S

IZ

E

V

O

L

Picture

Sound

Screen

Feature

Manual Setup

Program 01

Channel C06

Fine Tune 48

Name C06

Video PAL

Audio D/K

Search

Memory

Install

Move Select Exit

25

26

Watching Digital

Broadcasts

• To watch digital broadcasts:

- Purchase a separate

Digital Broadcasting

Receiver(SET-TOP BOX)

- Connect the PDP to a

Digital Broadcasting

Receiver as shown right.

1 Connect a Digital Broadcasting Receiver to the PDP

• Prepare A/V cables.

• Connect the cables from the digital TV Receiver output terminal to the

PDP(Component 1, 2) input terminal.

• When connecting the cables, be sure to match the cable colours.

Video Audio

Digital Broadcasting Receiver

(Set-Top Box)

2 Press the Power Buttons

• Turn the PDP and the receiver ON.

3 Input Select

C

O

M

PO

NE

NT

• Select [Component 1 or Component 2] by pressing the “COMPONENT” button of the remote control or using the “INPUT SELECT” button of the PDP unit.

• Each time you press the “COMPONENT” button, different input modes appear.

The sequence is as follows:

Component 1 Component 2

• N.B.: You cannot select component inputs if the picture in picture mode is on.

4 Select the Desired Channel and Function

• Select the desired channel and function by using the remote control of the Digital

Broadcasting Receiver.

NOTES:

1) Possible digital broadcasting signals: 1080i, 720p, 576p, 480p.

2) Antenna connection:

Apartment : Check if communal aerial receives digital broadcasts.

Private Houses: Set the indoor/outdoor UHF antenna to the direction of the digital broadcasting transmitting company.

3) For detailed connection method, refer to the owner’s manual of

Digital Broadcasting Receiver.

4) What is a component? : Signals with which luminance and chrominance are separated, producing a sharp picture.

5) If the Digital Broadcasting Receiver has PC output terminal or DVI output terminal, connect to ‘PC INPUT’ or ‘DVI INPUT’ at the rear of the panel of the PDP.

27

28

Watching Cable

Broadcasts

• To watch cable broadcasts, subscribe to your local cable TV broadcasting, and then connect a cable

Broadcasting Receiver to the PDP as shown right.

1 Connect a Cable Broadcasting Receiver to the PDP.

• Prepare the A/V cable.

• Connect the receiver(Output) to PDP(Video Input) as shown below.

• While using the scart cable for connection, put the ferrite core to the middle of the cable to prevent EMI (Electro Magnetic Interference).

AV3

AV1

Video/Audio

AV2

S-Video

Ferrite Core

Video/Audio

Cable Broadcasting Receiver

• N.B.: When using the AV3 input, there is no need to use both as S-Video will always take precedence on this input but you must have the right and left audio leads connected to produce sound when using S-Video.

2 Press the Power Buttons

• Turn the PDP and the receiver ON.

3 Input Select

AV

• Select [AV 1(Scart), AV 2(Scart) or

AV3(S-Video)] by pressing the [AV] button of the remote control or the

“INPUT SELECT” in keypad of the PDP unit.

• Each time you press the [AV] button, different input modes appear.

The sequence is as follows:

AV1 AV2

AV(S)3

• N.B.: An S-Video input into AV3 will take precedence over the normal yellow video lead so no need to utilise this if S-Video lead is used but you must still use the right and left audio leads to produce sound.

4 Select the Desired Program and Function

* Select the desired program and function by using the remote control of the Cable

Broadcasting Receiver.

NOTES:

1) If your local cable company re-transmits digital broadcasts, you may watch normal broadcasts and digital broadcasts simultaneously. For detailed information, refer to your local cable company.

2) A/V OUT OF SCART TERMINAL will provide with TV signal output of the selected channel.

29

30

Watching Satellite

Broadcasts

• To watch satellite broadcasting, subscribe to Digital Satellite

Broadcasting, then connect the satellite Broadcasting

Receiver to the PDP as shown right.

1 Connect a Satellite Broadcasting Receiver to the PDP.

• Prepare the A/V cable.

• Connect the receiver(Output) to PDP(Video Input) as shown below.

• When connecting to an external AV source, be sure to match the colours.

• If using the scart cable for connection, put the ferrite core to the middle of the cable for preventing EMI.

AV3

AV1 AV2

Video/Audio

S-Video

Ferrite Core

Video/Audio

Satellite Broadcasting Receiver

• N.B. : If using AV3 then S-Video takes precedence so no need for video lead if S-Video lead used the audio leads must still be used to produce sound.

2 Press the Power Buttons

• Turn the PDP and the Satellite receiver ON.

3 Input Select

AV

• Select [AV 1(Scart), AV 2(Scart) or

AV3(S-Video)] by pressing the [AV] button of the remote control or the

“INPUT SELECT” in keypad of the PDP unit.

• Each time you press the [AV] button, different input modes appear.

The sequence is as follows:

AV1 AV2

AV(S)3

4 Select the Desired Program and Function

• Select the desired program and function by using the Remote Control of the

Satellite Broadcasting Receiver.

31

32

Watching a

DVD Image

• Component Input is set to 480i/576i and

480p/576p mode.

• Connect the cable from the DVD Video output (Y, Pb/Cb,

Pr/Cr) to the

Component Input at the back of PDP, and connect the cable from DVD audio output (Left, Right) to the Audio Input at the back of PDP.

1 Connect a DVD Player to the PDP.

• Prepare the AV cable.

• Connect the DVD(Output) to the PDP(Component or Video Input) as shown below.

• When connecting to an external AV source, be sure to match the colours.

• If using the scart cable for connection, put the ferrite core to the middle of the cable for preventing EMI.

Video Audio

AV3

AV1 AV2

Video/Audio

S-Video

Ferrite Core

Video/Audio

DVD DVD DVD

• N.B. : Video input can be via scart cable S-Video lead or yellow phono jack.

The red and white plugs are for left and right audio to accompany the yellow video lead or to be used with the S-Video lead to produce sound.

2 Press the Power Buttons

• Turn the PDP and the DVD ON.

3 Input Select

C

O

M

P

O

NE

NT

AV

• Select [Component 1 or Component 2,

AV1(Scart), AV2(Scart) or AV3(S-Video)] by pressing the [COMPONENT] or [AV] button of the remote control or the “INPUT SELECT” in keypad of the PDP unit.

• Each time you press the [COMPONENT] or

[AV] button, a different input mode appears.

The sequence is as follows:

• [COMPONENT] button

Component 1 Component 2

• [AV] button

AV1 AV2

AV(S)3

4 Select the Desired Title and Function

• Select the desired title and function by using the remote control of the DVD.

NOTES:

1) Y/Cb/Cr, which stands for component video DVD player’s output can also be written as Y/B-Y/R-Y, Y/Pb/Pr depending on the kinds of DVD model.

2) The way of connecting the DVD to the PDP is as follows:

Y <---> Y Cb <---> Pb, B-Y, Cr <---> Pr, R-Y

3) The DVD output can be Video, S-Video or Component Video depending on the DVD model. There are various output modes, so be sure to check when you purchase it.

4) When connecting S-Video and Video simultaneously, only SVideo will be displayed on the screen as it takes precedence.

33

34

Watching a

VCR Image

• Video can use either the video terminal or the S-video terminal.

1 Connect a VCR to the PDP.

• Prepare the AV cable.

• Connect the Video(Output) to PDP(Video Input) as shown below.

• If using the scart cable for connection, put the ferrite core to the middle of the cable for preventing EMI.

AV3

AV1 AV2

Video/Audio

S-Video

Ferrite Core

Video/Audio

VCR

2 Press the Power Buttons

Turn the PDP and the VCR ON.

3 Input Select

AV

• Select [AV 1(Scart), AV 2(Scart) or AV 3(S-

Video)] by pressing the [AV] button of the remote control or the “INPUT SELECT” in keypad of the PDP unit.

• Each time you press the [AV] button, different input modes appear.

The sequence is as follows:

AV1 AV2

AV(S)3

4 Select the Desired Title and Function

* Select the desired title and function by using the remote control of the VCR.

NOTES:

1) When connecting a VCR the S-Video terminal provides a better image than the Video terminal.

2) When connecting to the Video terminal, connect 3 colour AV cables (video, left audio, right audio) to the PDP; for the SVideo terminal, connect the Audio terminal (Left, Right) in the same way, and connect the S-Video cable (sold separately).

3) When connecting the Video terminal and the S-Video simultaneously, the S-Video terminal is selected. This can be checked by the [Recall] button of the remote control.

35

36

Watching a

Camcorder/Game

Console Image

• Enjoy images recorded by camcorder or the game console after connecting to the

1 Connect a Camcorder/Game Console to the PDP.

• Prepare the AV cable.

• Connect the Video(Output) to the PDP(Video Input) as shown below.

• When connecting to an external AV source, be sure to match the colours.

• If using the scart cable for connection, put the ferrite core to the middle of the cable for preventing EMI.

AV3

AV1

Video/Audio

AV2

S-Video

Ferrite Core

Video/Audio

Game Console/Camcorder

2 Press the Power Buttons

• Turn the PDP and the

Camcorder/Game Console ON.

3 Input Select

AV

• Select [AV 1(Scart), AV 2(Scart) or AV 3] by pressing the [AV] button of the

Remote Control or the “INPUT SELECT” in keypad of the PDP unit.

• Each time you press the [AV] button, different input modes appear.

The sequence is as follows:

AV1 AV2

AV(S)3

4 Select Function

• Select the function by using the remote control of camcorder or game console.

NOTES:

1) When connecting the device, the S-Video terminal provides a better image than the Video terminal.

2) When connecting to the Video terminal, connect 3 colour AV cables (video, left audio, right audio) to the PDP; for the SVideo terminal, connect the Audio terminal (Left, Right) in the same way, and connect the S-Video cable(sold separately).

3) If connecting via component video, refer to “Watching a DVD

Image” on page 32-33.

37

38

Connecting PC

• This product supports resolutions of VGA, SVGA, XGA.

• Before connecting a

PC to the PDP, be sure to adjust the resolution of the PC.

1 Before Connecting to the PDP, Set the

Resolution of the PC.

• Go to SETUP-CONTROL PANEL-DISPLAY PROPERTIES in Window Screen of the PC.

• Choose the SETTINGS tab in the DISPLAY menu.

• In the SETTINGS menu, select 640 x 480 or 800 x 600.

2 Connect the PC to the PDP.

• Prepare the PC cable (D-sub 15pin) and the PC audio cable.

• Connect the PC(Output) to the

PDP(Input) as shown below.

Audio 15 PIN D-sub

PC

3 Press the Power Buttons.

• Turn on the PDP and the PC.

4 Input Select

PC

/D

V

I

• Select [PC] by pressing the [PC/DVI] button of the remote control or PDP unit.

• Each time you press the [PC/DVI] button, a different input mode appears.

The sequence is as follows:

PC DVI

• N.B. : You cannot select PC or DVI if the picture in picture mode is on.

5 Enjoy Dynamic Ultra Screen Monitor by

Using PC’s Keyboard or Mouse.

NOTES:

1) The resolution of the PC monitor is the best at 640 x 480 (VGA).

2) If there is a [Vertical Frequency]setting menu in the [Display] menu of the PC, adjust the frequency to 60Hz.

3) If the PC resolution is too high, it may be hard to read letters.

Select a suitable resolution.

4) If the picture don’t fit with the size or position of the screen, select the [Auto] function in the Screen Menu in order to make fit automatically. Also, you can adjust the position of the picture with [H.position] and [V.position] functions manually.

39

40

Connecting PC

• This product supports resolution of VGA, SVGA,

XGA.

• Before connecting a PC to the PDP, be sure to adjust the resolution of PC.

• This product is supported by Plug and Play only at

DVI.

1 Before Connecting to the PDP, Set the Resolution of the PC.

• Go to SETUP-CONTROL PANEL-DISPLAY PROPERTIES in Window Screen of the PC.

• Choose the SETTINGS tab in the DISPLAY menu.

• In the SETTINGS menu, select 640 x 480 or 800 x 600.

2 Connect the PC to the PDP.

• Prepare the DVI cable and the PC audio cable.

• Connect the PC(Output) to the PDP(Input) as shown below.

DVI-D INPUT

Audio DVI

PC

3 Press the Power Buttons.

• Turn on the PDP and the PC.

4 Input Select

PC

/D

V

I

• Select [DVI] by pressing the [PC/DVI button of the remote control or the Input button on the PDP unit.

• Each time you press the [PC/DVI] button, a different input mode appears.

The sequence is as follows:

PC DVI

• N.B. : You cannot select PC or DVI if the picture in picture mode is on.

5 Enjoy Dynamic Ultra Screen Monitor by

Using PC’s Keyboard or Mouse.

NOTES:

1) The resolution of the PC monitor is the best at 640 x 480 (VGA).

2) If there is a [Vertical Frequency]setting menu in the [Display] menu of the PC, adjust the frequency to 60Hz.

3) If the PC resolution is too high, it may be hard to read letters.

Select a suitable resolution.

4) DVI input port receives only digital signal.

5) Depending on the graphic card when plugged or unplugged the

DVI connection the screen may not display correctly.

Restart the computer if this happens.

41

• Depending on graphic card, problems like no signal detected or line noises can happen. If these problems happen, contact the graphic card company for help.

Resolution

640x400

640x480

720x400

800x600

1024x768

H Freq. (KHz)

37.879

48.077

46.875

53.674

48.363

56.476

60.023

68.677

37.861

31.469

37.861

37.500

43.269

31.469

37.927

35.156

V Freq. (Hz)

60.317

72.188

75.000

85.061

60.004

70.069

75.029

84.997

85.080

59.940

72.809

75.000

85.061

70.087

85.039

56.250

Remark

VESA

VESA

VESA

VESA

VESA

HP & VESA

VESA

VESA

VESA

DOS

VESA

VESA

VESA

IBM

VESA

VESA

DVI

O

O

O

O

O

O

O

O

O

O

O

O

O

PC

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

O

42

44

Selecting

Picture Mode

• Select the Picture mode that is appropriate depending on the kinds of pictures, you enjoy.

1 Selecting Picture Mode

• Press the [PICTURE MODE] on the remote control.

• While pressing the [PICTURE MODE] for the first time, the current picture mode will be displayed.

2 Each Press of the Button Will Select

One of Four Picture Modes.

• Each time you press the button, a different picture mode appears.

The sequence used is as follows:

Normal Dynamic Cinema User

* Normal : For a highly defined image in a normally bright room

* Dynamic: For a clear-cut image emphasizing high contrast for sports viewing

* Cinema: For a movie

* User: Allows the user to customise settings as desired.

3 Menu on the Screen will disappear.

• After selecting a desired picture mode, the menu on the screen will disappear.

• If you want to customise the picture modes, refer to the following page.

NOTES:

1) Normal, Dynamic, and Cinema modes are factory preset values.

2) When adjusting sub-menus while you are in Normal, Dynamic, and Cinema modes, the Picture Mode will be automatically converted to User Mode, and the adjustments will be made.

3) Selecting [Initialise] in the [Features], menu will allow the

Brightness, Contrast, etc. to return to the factory preset values.

1 Press the MENU Button.

• The MENU shown below will display on the screen.

Picture

Mode Normal

Sound

Screen

Feature

Colour Temp. Normal

N.R. On

CTI On

Install

Move Select Exit

2 Press the ▼PR▲ Button.

• After selecting [Picture] by the “ PR ”, buttons, press the “VOL ” button. Then the sub menu of [Picture] will be displayed.

Mode Normal

Picture

Sound

Screen

Feature

Colour Temp. Normal

N.R. On

CTI On

Install

Move Adjust Exit

3

V

O

L

P

R

E

V

PR

Select the User Mode.

PR

• Select [User] by the ” VOL ” buttons in the

[Mode].

MENU

SC

RE

EN

S

IZ

E

V

O

L

Picture

Mode User

PR

Sound

Screen

Feature

Colour Temp. Normal

N.R. On

CTI On

Install

Move Adjust Exit

Customising

Picture

• You can adjust the colour tone and brightness to your preference.

45

46

4 Select User Mode Adjustments

• While you are in [Picture Mode – User], press the “ PR ” buttons to select a specific adjustment item.

Mode User

Picture

Sound

Screen

Feature

Colour Temp. Normal

N.R. On

CTI On

Install

Move Adjust Exit

5

V

O

L

Picture Condition Adjustments

PR

• Press the “ VOL ” buttons to adjust the picture of your preference.

• N.R. and CTI function adjust the noise reduction and color resolution level of picture respectively.

MENU

SC

RE

EN

S

IZ

E

V

O

L

P

R

E

V

PR

PR

Picture

Mode User

Sound

Screen

Feature

Colour Temp. Normal

N.R. On

CTI On

Install

Move Adjust Exit

NOTES:

1) While you are in the PC or DVI input mode, you can only adjust brightness, contrast and colour temperature.

2) When you adjust Brightness, Contrast, and Colour in DTV mode or adjust Brightness and Contrast in PC and DVI mode, the picture is adjusted finely.

3) The Tint control is used when the input signal is NTSC or

Component. If input signal is NTSC, Tint control is displayed in picture menu.

4) Selecting the colour temperature makes the mood : normal, warm or cold.

1 Press the SCREEN SIZE Button.

• The current screen size will be displayed on the screen.

• Each time you press the SCREEN SIZE button on the remote control, a different screen size appears. The sequence used is as follows in case of AV and TV modes :

Auto 16:9 4:3

Panorama

LBS(14:9)

Adjusting with

Screen Size button

• You can adjust screen size or aspect ratio as desired.

LB(14:9) LB(16:9)

14:9 LBS(16:9)

• N.B. : You cannot select screen size if the picture in picture mode is on.

NOTES:

1) Displaying a picture in a 4:3 mode for a long time may cause phosphor of the PDP to be burned. So avoid displaying a picture in 4:3 screen size for a long time.

2) Under Component,PC and DVI inputs,only 16:9,4:3 and panorama are available.

3) Auto : Displays pictures of original picture size.

16:9 : 16:9 picture formats

14:9 : 14:9 picture formats

4:3 : 4:3 picture formats like an analog TV

Panorama : 16:9 picture formats with panorama effect

LB : Enlarges the screen as to fill the black part above and below the picture.

LBS : Enlarges the screen, and shifts up as to see the subtitles in case you are watching video with subtitles.

47

48

Adjusting Screen in the MENU

Adjusting Screen

• You can adjust the screen in the menu.

1 Press the MENU Button.

• The MENU screen as shown below will appear.

Mode Normal

Picture

Sound

Screen

Feature

Colour Temp. Normal

N.R. On

CTI On

Install

Move Select Exit

2 Press the “ ▼PR▲ ” Button.

• Press the ” PR ” buttons to select ‘Screen’.

Picture

Sound

Screen

Feature

H. Position.

V. Position

32

32

Auto

Install

Move Select Exit

< In case of PC input >

3

V

O

L

Press the Volume “ VOL ” Buttons.

PR

MENU

SC

RE

EN

S

IZ

E

V

O

L

• Press the Volume “ VOL ” buttons to enter the sub menu “Screen”.

• While you are in ‘Screen’ menu, press the ” PR” or

“PR ” button to select a desired item, and then, adjust the value by pressing the “ VOL” or “VOL ”

P

R

E

V

PR

PR

Picture

Sound

H. Position.

V. Position

Auto

Screen

Feature

Install

Move Adjust

< In case of PC input >

Exit

32

32

Screen Mode

Function

• This function is same to the [Screen Size] of remote controller.

NOTES:

1) Screen Menu is different according to the input modes.

Input

AV / TV

Available Screen Mode

16:9, 4:3, Panorama, LB(16:9), LBS(16:9),

14:9, LB(14:9), LBS(14:9), Auto

16:9, 4:3, Panorama Component, PC, DVI

2) Other Screen adjustments

< Under PC mode >

[H. Position] : As the value increases, the screen moves to the right.

[V. Position] : As the value increases, the screen moves up.

[Auto] : Adjusting automatically the screen to optimum states.

< Under PIP mode >

[PIP Size] : Adjusting the size of the sub-picture.

[Alpha Blend] : Adjusting the translucent rate of the subpicture.

49

50

Watching a STILL Image

Watching a

Still Image

• You can view still images with this function. However, displaying the same images such as still images for a long time may cause image burn.

1 Press the “STILL” Button.

• If you wish to freeze a picture, press the

“STILL” button. You can still hear the sound.

• Press “STILL” button again to cancel the

“STILL” function.

Still

NOTES:

1) Displaying the same images such as still images for a long time may cause image burn (after-image lagging).

2) In this case, such “image burn” may become less noticeable if moving images are later displayed for a long time.

3) However, an image burn may become a permanent one, damaging the Plasma Display; therefore, avoid displaying the same images for a long time.

4) Use the function [ISM], while displaying still images for a long period of time to minimize this effect.

ISM (on or off ) is in the Feature menu.

Main

• PIP (Picture-in-Picture) and P-by-P(Picture-by-Picture) modes allow users to watch two pictures simultaneously.

POP mode is used in searching memorized 5 or 12 channels.

1 Engaging PIP mode

• Press the ‘PIP’ button once on the remote control to engage the Picture-in-Picture mode.

• By pressing the button repeatedly, it will show the following cycle.

• If switched to P-by-P (Picture-by-Picture) mode, the screen will be split in half. The screen on the left side is the main picture, and the sub-picture will be on the right of the screen.

Screen Adjustment of the Sub-picture

2

Main

PIP

Sub

Main

P-by-P

Sub

POP5

Sub1 Sub2 Sub3

Sub4

Main

Sub5

POP12

Sub1 Sub2 Sub3 Sub4

Sub12

Sub11

Main

Sub5

Sub6

Sub10 Sub9 Sub8 Sub7

Position of the Sub-picture

• When PIP mode is engaged, the sub-picture can be displayed in one of the four corners by using ‚POSITION’ button.

• Whenever pressing the button, the sub-picture will be cycling in the following order.

Also, using “ PR ” and “ VOL ” button, the sub-picture can be moved to any position you want.

• Size and Alpha Blend of the subpicture can be adjusted on Screen Menu of OSD.

• These fuctions are availible only in PIP Mode.

Pip Size

Adjusting the size of the sub-picture with “ VOL ” buttons.

Alpha Blend

The adjustment of alpha blend allows the sub-picture to be translucent.

The translucent rate is controlled with “ VOL ” buttons.

<Using ‘Position’ button>

Main

Sub

Main

Sub

< Using „ buttons>

PR ” and „ VOL ”

Sub

Main Sub

Sub

3

Main

Swap the pictures

• In order to swap between the main picture and subpicture, press the ‘SWAP’ button.

• However, at POP5 and POP12, the pictures are not swapped. Main picture will change to the active subpicture.

• Also, only TV channels are available for the sub-pictures of

POP5 and POP12.

The sub-pictures search channels continuously until POP mode is exited.

51

52

4 Select the program

• Using program Up/Down buttons

(PR /PR ), you may select the desired channels for sub-pictures.

• The PR Up/Down buttons select the

TV channels.

5 Select the Input Source

• Various signal sources can be displayed within the sub-picture under PIP mode.

• Once the PIP mode is on, you may change the input source of the sub-picture by pressing the ‘SOURCE’ button.

• Pressing the ‚SOURCE’ button repeatedly will cycle through following order.

T V → AV1 → AV2 → AV3

6 Available PIP Input Combinations

• Main-pictue and sub-pictue input combinations

PIP

MAIN TV

(MAIN)

TV

(MAIN)

AV1

(CVBS)

AV2

(CVBS)

O

O

O

AV1

(CVBS)

O

X

O

AV2

(CVBS)

O

O

X

AV3 O O O

AV3

O

O

O

X

S-VIDEO

O

AV1

(RGB)

O

O

O

X

X

O

O

AV2

(RGB)

O

O

X

O

S-VIDEO

AV1

(RGB)

AV2

(RGB)

O

X

X

O

X

X

O

X

X

X

X

X

X

X

X

O

X

X

O

X

X

1 Select “SOUND MODE”.

• Press the “SOUND MODE” on the remote control.

• While pressing the “SOUND MODE” for the first time, the current sound mode will be displayed.

2 KEvery Press of the Button Changes Modes.

• Each time you press the button, a different sound mode appears.

The sequence used is as follows:

Adjusting Auto

Sound Mode

• Enjoy various sound modes by selecting your favourite Sound

Mode depending on the kinds of moving pictures.

Normal Movie Music News User

* Normal : Suitable for watching any motion picture

* Movie : Select this mode to simulate being at a movie theatre

* Music : Ideal for listening to music

* News : Allows human voice to be heard more clearly

* User : Allows the user to adjust as desired.

3 MENU will Disappear.

• After selecting a desired Sound Mode, the on-screen menu will disappear in about

2~3 seconds.

• Normal, Movie, Music and News modes are factory preset values.

If you want to customise the sound modes for your preference, refer to the following page.

53

Customising Sound Mode

54

Customising

Sound Mode

• This feature allows the user to adjust for their preference.

1 Press the MENU Button.

• The MENU screen as below will be displayed.

Picture

Sound

Screen

Feature

Mode Normal

Brightness 32

Contrast 48

Sharpness 32

Color 32

Colour Temp. Normal

N.R. On

CTI On

Install

Move Select Exit

2 Press the “ PR ” Button.

• Select [Sound] by the “ PR ” buttons, then press the “VOL ” button to display the following.

Picture

Sound

Screen

Effect Off

AVC Off

Mode Normal

Feature

Install

Move Select Exit

3

V

O

L

P

R

E

V

PR

Select SOUND BALANCE.

PR

• Select “Sound-Balance” by the “ VOL ” buttons, then adjust it.

MENU

SC

RE

EN

S

IZ

E

V

O

L

PR

Picture

Effect Off

AVC Off

Mode Normal

Sound

Screen

Feature

Install

Move Adjust Exit

4 Select the Effect Mode.

• Select [Effect] by pressing the “ PR ” then select the desire sound effect by pressing the

“VOL ” button.

• [Effect]: Used to emphasize stereo effect.

Picture

Sound

Screen

Effect Off

AVC Off

Mode Normal

Feature

Install

Move Adjust Exit

Language selection for dual language broadcast

• If a programme is received in two languages (dual language), you can switch to Dual I, Dual II or F mono by pressing the I/II button of the remote control repeatedly.

Dual I

Dual I sends the primary broadcast language to the loudspeakers.

Dual II

Dual II sends the secondary broadcast language to the loudspeakers.

F Mono

F Mono sends the Mono sound to the loudspeakers.

55

56

5

V

O

L

Select the Sound Mode.

PR

• Select the Sound Mode by pressing the

“ PR ” buttons, then adjust it by pressing the “ VOL ” buttons.

P

R

E

V

PR

MENU

PR

SC

RE

EN

S

IZ

E

V

O

L

Picture

Effect Off

AVC Off

Mode Normal

Sound

Screen

Feature

Install

Move Adjust Exit

Normal Movie Music News User

* Normal : Suitable for watching any motion picture

* Movie : Select this mode to simulate being at a movie theatre

* Music : Suitable for listening to music

* News : Allows human voice to be heard more clearly

* User : Allows the user to adjust as desired.

NOTES:

1) User Mode : Used as an equalizer with which the user can adjust the sound frequency as desired.

2) If you modify the sound frequency in auto Sound Mode

(News, Movie, Music, etc.), it is automatically switched to the

User Mode.

3) For a realistic sound effect, lower than 120Hz frequency sound and greater than 12kHz frequency adjust the equalizer accordingly.

4) AVC function : This function adjusts volume to the set level automatically. However, dependent on the sources, it may have different volume levels because the sound sources have their own initially set up levels.

1 Press the Input Signal Selecting Button.

TV

VCR/DVD

SAT

• Press the “TV”, “AV”, “COMPONENT” or “PC/DVI” button on the remote control or the PDP Display to select the desired input signal.

• Each time you press input mode buttons, a different input mode appears.

The sequence used is as follows:

• “TV ” button

CATV

TV

• “AV ” button

AV1 AV2 AV3

• “COMPONENT” button

Component1

• “PC/DVI” button

PC

Component2

DVI

INPUT SIGNAL

• Used to select INPUT signal of external device connected to the PDP.

Component 1

NOTES:

1) If an external device is not connected or INPUT signal is not applied a Warning Message (“No Signal”) will be displayed.

2) In this case, check if external device is connected and/or terminal connection is properly fitted.

3) Also, you can select input using [INPUT SELECT] button in the keypad of the PDP unit. The sequence of selection is as follows:

TV -> AV1 -> AV2 -> AV3 ->Component1

-> Component2 -> PC -> DVI -> TV

57

58

Checking the Current Input Signal

- Press the [RECALL] button on the remote control, then displays basic informations of the current input signal,

Under this state, pressing the [RECALL] button once more, additional informations about the current input signal will be displayed on the OSD.

Checking the

Current Input Signal

• Used to check the

INPUT signal mode, current time, resolution, channel, etc.

1 Press the RECALL Button.

• Press the [RECALL] button on the Remote Control.

Component 1

PM 12:00

[RECALL] button

H:1920

V:1080

[RECALL] button once more

1. If you watch Component, PC, or DVI :

Comopnent 1

PM 12:00

Displays which input terminal is used, and indicates the input signal mode.

Indicates the horizontal and vertical resolution of the current INPUT signal.

H:1920

V:1080

Indicates the mode and current time.

2. If you watch TV:

PR22 PR Name Displays the program number and its name.

Indicates the current sound state and time.

Video PAL B/G

Audio I

Country GB

Channel C35

Displays additional informations of TV signal of TV signal, video and audio system. country, channel.

3. If you watch VCR image:

AV1

PM 12:00

Displays the program number and input terminal, which is used.

Indicates the mode and current time.

Video PAL B/G

Displays the video system of input signal

NOTES:

1) “1920 x 1080” displayed in the INPUT signal is not the resolution of the monitor, but the signal that is sent by the

Digital Broadcasting Receiver.

1 Press the MENU Button.

• The MENU screen will be displayed as below.

Mode Normal

Picture

Sound

Screen

Feature

Colour Temp. Normal

N.R. On

CTI On

Install

Move Select Exit

2 Press the “ PR ” Button.

• Select [Features] by the “ PR ” button.

Picture

Sound

Language English

Child Lock Off

MGDI On

Auto Power

Time Setting

Off

ISM

Initialize

Screen

Feature

Install

Move Select Exit

3

V

O

L

Select the menu Background.

PR

• Select the MENU [Background] by pressing the “VOL ” button.

• Adjust the tanslucent level of OSD background using “VOL ” buttons.

P

R

E

V

PR

MENU

PR

SC

RE

EN

S

IZ

E

V

O

L

Picture

Sound

Screen

Language English

Child Lock Off

MGDI On

Auto Power Off

Time Setting

ISM

Initialize

Feature

Install

Move Adjust Exit

Selecting

Languages

• Used to select the tanslucent level of MENU background and language used in MENU.

59

60

4 Select LANGUAGE by using the “ PR ”Button.

• Select [Language] by using the” PR ” button.

• Every press of the “VOL ” button while you are in the [Language] mode would cycle through the different languages.

Picture

Sound

Screen

Language English

Child Lock Off

MGDI On

Auto Power Off

Time Setting

ISM

Initialize

Feature

Install

Move Adjust Exit

NOTES:

• When power is turned on the first time, ‘SELECT

LANGUAGE’ mode will be displayed, then, select the desired language by using “VOL ” button.

(Displayed only once)

5 Child Lock Setting

• Select [Child Lock] by the “ PR ” buttons.

• Whenever “VOL ” button is pressed, the lock mode would cycle On and Off.

• While the Child Lock is ON, if you have not turned off the PDP, all of it’s keys will work normaly. However, after turning the PDP off, the PDP will not be turned on with the keypad on the PDP. Only by the remote controller, the

PDP is turned on.

Picture

Sound

Screen

Feature

Install

Move

Language English

Child Lock Off

MGDI Off

Auto Power Off

Time Setting

ISM

Initialize

Adjust Exit

1

MGDI is the image enhancement technology of Daewoo Electronics, which provides more clear, realistic, and delicate images.

Press the MENU Button.

• The MENU screen will be displayed as below.

MGDI

Picture

Mode Normal

• MGDI function can not be used In PC and DVI modes.

Sound

Screen

Colour Temp. Normal

N.R. On

CTI On

Feature

Install

Move Select Exit

2 Select Features

• Select [Features] by the “ PR ” button.

Picture

Sound

Language English

Child Lock Off

MGDI On

Auto Power

Time Setting

Off

ISM

Initialize

Screen

Feature

Install

Move Select Exit

3 MGDI Setting

• Enter the sub Menu by using the “VOL ” button.

• Select the [MGDI] by pressing the “ PR ” button.

• You can select [MGDI] On or Off mode by using the “VOL ” button.

Picture

Sound

Screen

Language English

Child Lock Off

MGDI Off

Auto Power Off

Time Setting

ISM

Initialize

Feature

Install

Move Select Exit

61

62

POWER/STANDBY

Indicator

Front panel LED lights

• When the AC power is on : Green.

• When the AC power is in the standby mode : Red.

1 Auto Power Setting

• Select the [Auto Power] by pressing the “ PR ” button from [Features].

• You can select [Auto Power] ON and OFF mode by using the “VOL ” button.

Picture

Sound

Screen

Feature

Install

Move

Language English

Child Lock Off

MGDI Off

Auto Power

Time Setting

Off

ISM

Initialize

Adjust Exit

Auto Power

1) ON : When the AC power is ON, the TV will be turned on automatically without pressing the power button on the remote control.

AC POWER ON PDP SET ON

Automatically

2) OFF : When the AC power is ON, the TV will be turned on by pressing the power button on the remote control or the keypad of the front panel.

AC POWER ON STANDBY MODE PDP SET ON

With the remote control or the keypad of front panel.

3) If Child Lock function is ON, this function is not operated.

1 Press the MENU Button.

• The MENU screen will be displayed as below.

Picture

Mode Normal

Sound

Screen

Feature

Colour Temp. Normal

N.R. On

CTI On

Install

Move Select Exit

2 Select Features

• Select [Features] by the “ PR ” button.

Picture

Sound

Language English

Child Lock Off

MGDI On

Auto Power

Time Setting

Off

ISM

Initialize

Screen

Feature

Install

Move Select Exit

3 Select Time Setting

• Enter the sub menu by using the “VOL ” button.

• Select the [Time Setting] with the “ PR ” button.

• Enter [Time Setting] by pressing the “VOL ” button.

Picture

Sound

Screen

Feature

Install

Move

Language English

Child Lock Off

MGDI Off

Auto Power

Time Setting

Off

ISM

Initialize

Select Exit

63

64

Time Setting

• The “Current time” must be set up ahead of setting up other time memories.

4 Off-Time and Wake time setting

• Select Functions by pressing the “ PR ” button. First, set [Clock]- current time, and then You can setup off-time and wake time.

• [Clock] : Adjust the desired hour and minute with “◄VOL►” button.

• [Auto Clock] : Automatically setting the current time by teletext signal.

• [Off Time] and [Wake Time] Setting methods are same as [Clock] setting method.

• [Off Timer] and [Wake Timer] : Setting [On] and [Off] of each Timer.

• [Wake Prog.] and [Wake Vol. ] : Setting channel and volume when TV is turned on by

[Wake Timer].

Picture

Sound

Screen

Feature

Auto Clock

Off Timer

Off Time

Wake Timer

Wake Time

Wake Prog.

Wake Vol.

Time Setting

On

Off

AM 12:00

Off

AM 12:00

2

19

Install

Move Select Exit

Time Setting Functions

1) This time memory function automatically turns the TV set “On” or “Off”at a desired time. Once set up, this function works every day unless the set time is canceled or the TV set is unplugged.

Therefore, this function could be used for a “Get up” alarm (Wake up Call) by setting up the time for “On” in the morning.

2) However, if you once power off with ON/OFF in the PDP unit, the

Current time (Clock) will be reset.

1 Press the MENU Button.

• The MENU screen will be displayed as below.

Picture

Mode Normal

Sound

Screen

Feature

Colour Temp. Normal

N.R. On

CTI On

Install

Move Select Exit

2 Press the “ PR ”Button.

• Select [Features] by the “ PR ” button.

Picture

Sound

Language English

Child Lock Off

MGDI On

Auto Power Off

Time Setting

ISM

Initialize

Screen

Feature

Install

Move Select Exit

3 Select ISM.

• Enter the sub menu by using the “VOL►” button.

• Select the [ISM] by pressing the “▼PR▲” button.

• Press of the “VOL►” button while you are in the ISM.

Picture

Sound

Screen

Language English

Child Lock Off

MGDI Off

Auto Power Off

Time Setting

ISM

Initialize

Feature

Install

Move Select Exit

ISM

• Image Burn Minimisation

• Displaying a still image for a long time causes part image sticking on the screen.

• The ISM function minimises this effect.

65

66

4 Select Functions.

• Every press of the “VOL ” button after select function by the “ PR ” button would switch between ON/OFF.

ISM

On

Off

Off

Picture

Sound

Pixel Shift

Low Bright.

Img. Invert

Screen

Feature

Install

Move Adjust Exit

NOTES:

* Pixel Shift : The whole screen shifts up/down, left/right at 15 sec interval to minimize image sticking.

* Low Bright: When displaying a still picture or a fixed pattern for a long time (5Min), the brightness level decreases to minimize image sticking.

* Image Inverting: Inverting color of the original image to minimisation image sticking.

1 Press the MENU Button.

• The MENU screen will be displayed as below.

Picture

Mode Normal

Sound

Screen

Feature

Colour Temp. Normal

N.R. On

CTI On

Install

Move Select Exit

2 Select Features

• Select [Features] by the “ PR ” button.

Picture

Sound

Language English

Child Lock Off

MGDI On

Auto Power Off

Time Setting

ISM

Initialize

Screen

Feature

Install

Move Select Exit

Back to

Initialization

• You can restore the values of the adjustment setting made in the

MENU back to factory settings.

67

68

3 INITIALISATION

• Enter the sub Menu by using the “VOL ” button.

• Select the [Initialize] by pressing the “ PR ” button, then press the “VOL ” button.

• A confirmation message will be displayed.

• To perform initialization, press the “VOL ” button after selecting [YES] by the “ PR ” button.

• To return to MENU, press “MENU” button.

Picture

Sound

Screen

Language English

Child Lock Off

MGDI Off

Auto Power Off

Time Setting

ISM

Initialize

Feature

Install

Move Select Exit

Are You sure ?

Picture

Sound

Screen

Feature

Install

Move

No

Yes

Select Exit

When [INITIALIZATION] is completed:

1) When [INITIALIZATION] is completed, those values that have been set in the User Mode of [PICTURE MODE] and [SOUND MODE] will be returned to the factory preset values.

2) Once initialized, you can not undo.

3) The items in the [SCREEN] Menu are also initialized.

4) Language, program, time, volume, OSD background, input mode are not initialized.

1 Press the “SLEEP” Button.

• Press the “SLEEP” button on the Remote

Control.

• Pressing the “SLEEP” button first time will display the current setting for Sleep Timer.

• To cancel the Sleep Timer, press the “SLEEP” button to select ‘Off’.

Setting

Sleep Timer

• Sleep Timer turns the PDP off after a preset time.

Sleep Timer Off

Sleep Timer off

Sleep Timer 15

Sleep Timer 30

Sleep Timer 120

Sleep Timer 90

Sleep Timer 60

NOTES:

1) On-screen information disappears if you do not take any action for about two seconds after pressing the SLEEP button.

2) If you turn the PDP off after setting SLEEP, the setting is erased.

69

70

Switching Teletext ON/OFF

• Press the Text button ( ). The index page or the page viewed last will appear. Press the Text button again to return to the TV mode.

Colour buttons in TOP/FLOF Teletext

• A red, green, yellow and cyan field is shown at the bottom of the screen. If TOP or FLOF Teletext is transmitted by the station, pressing the corresponding colour button on the remote control, you can select the desired page easily.

Selecting Pages

• The Page selector button 0~9 are used to enter a page number.

The selected page number appears at the top of the screen and the page appears after a short time.

The UP( or )/( or ) buttons increase or decrease the current page number by 1.

Index Page

• You can switch directly to the program preview (with

TOP text) or the overview page of the station you are currently viewing by pressing the Index ( )button.

Page Hold

• Several sub pages can be combined under a page number and are scrolled at an interval determined by the television station. The presence of sub pages is indicated by, for example, 3/6 beneath the time, which means that you are looking at the 3rd page of a total of 6pages.

If you want to look at a subpage for a longer period of time, press the Hold ( ) button.

The contents of the subpage shown are kept no longer updated or switched to other subpages. Pressing the Hold button again, the current subpage appears.

Calling Up Subpage Directly

• Pressing the Subpage ( ) button. The subpage number is displayed at the bottom of the screen. To change the subpage, press the subpage number, for example, the

2nd page, sequence 02.

The desired subpage will eventually be displayed on the screen and holds it there.

Press this button again to exit this function.

Watching television during teletext mode

• Some pages are continually updated, for example, stock market reports, sports announcements, the latest news.

If you want to watch television and stay informed at the same time, press Update (

X

)button.

The regular program is still visible and the teletext page number appears at the top of the screen. Pressing the

Update button, the teletext page appears with the updated information.

Reveal Answer

• This function can be used on certain pages to reveal the solution of riddles. Press the Reveal button ( ) to reveal a hidden answer and press again to hide it.

Doubling Character size

• Repeatedly pressing the Size button ( ) doubles the character size in the following order. Upper half of the page → Lower half of the page → Return to normal size.

Mix

• You can simultaneously watch TV and Teletext screen by pressing the mixed window button ( ) in Teletext mode.

71

72

Before requesting for service, check the following points once again.

• Remote control does not function properly.

• Check for any obstacle between the

Remote Control and the Display.

• Check for dead batteries and incorrect battery orientation.

• Check if the Remote Control is the right one.

• Remove any obstacle between the

Remote Control and the Display.

• Replace batteries and use the correct polarity (+) or (-) of the batteries.

• Use the correct Remote Control proper to the model.

• The Display makes a snapping sound.

• There are empty spots at the top and the bottom area of the screen.

• Check if the pictures and sound are normal.

• This sound is produced due to variations in room temperature.

• This sound does not indicate that the

Display has a problem if the pictures and sound can be viewed and heard properly.

• Check if the screen size of an image is wider than 16:9 aspect ratio

(theatre screen size).

• When video screen is wider than

16:9 aspect ratio, you may see dark areas at the top and the bottom of the screen.

Before Requesting for Service

• There are spots on the screen or screen rolls.

• Screen size is suddenly changed.

• Check if your product is affected by any interference from automobiles, high-voltage transmission lines, neon signs or other potential sources.

• The screen size of a video image may not be matched to the size of the dark initial screen.

• Check by using other video tape.

SPECIFICATIONS

DISPLAY UNIT

Diagonal Size

Screen Aspect Ratio

System

Display Resolution

Pixel Pitch

Dimension

Weight

Power Requirement

106 cm (42”)

16:9

PAL B/G, I/I, SECAM B/G, D/K, L/L’

852(H) x 480(V) dots

1,08(H) x 1,08(V) mm

1260(Sz.) x 653(W) x 91(Gł.) mm

49.61(Sz.) x 25.71 (W) x 3.50 (Gł) inch

33 kg (72.75Lbs)

100-240V~, 50/60 Hz

* Appearance and specifications of this product are subject to change for improving the product without prior notice.

CONNECTION TERMINAL

ITEMS

DVI INPUT

PC INPUT

Component INPUT

AV 1,2

EXTERNAL

INPUT

AV3

TV

VIDEO

DVI-D Digital Only Jack one 15 pin D-sub jack two Y, Pb/Cb, Pr/Cr RCA Jack

SCART Jack

(Video In/Out, RGB In)

AUDIO

(LEFT/RIGHT)

(LEFT/RIGHT)

2sets (LEFT/RIGHT)

(LEFT/RIGHT)

(In/Out)

RCA Jack, S-VHS (LEFT/RIGHT)

Standard : PAL B/G, I/I, SECAM B/G, D/K, L/L’

Receiving Channel :

VHF Low : E2 ~ S6 Ch. (48.25MHz ~ 140.25MHz)

VHF High : S7 ~ S36 Ch. (147.25MHz ~ 423.25MHz)

UHF : S37 ~ E69 Ch. (431.25MHz ~ 855.25MHz)

L’-SECAM : FB, FC1, FC

AUDIO

OUTPUT

20W (10W + 10W), 8 Ohm

73