Electrolux EDI97170W User's Manual

user manual
Iron Aid
EDI97170W
2 electrolux
Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com
Contents
Important safety information
Environment
Product description
Control panel
What is shown in the display
Before first use
Sorting and preparing laundry
Starting up for the first time
Iron AidTM Steam System
Starting an Iron AidTM programme
Drying
2
4
5
6
6
6
7
7
8
12
13
Starting a drying programme
Drying rack
Cleaning and maintenance
What to do if ...
Technical data
Machine settings
Hints for test institutes
Installation
Service
Guarantee/Customer Service
European Guarantee
15
16
17
20
22
23
24
24
26
26
27
Subject to change without notice
Important safety information
Important! Only operate the Iron Aid
programmes with distilled water!
Mains water causes damage to the appliance.
Important! In the interest of your safety
and to ensure the correct use, before
installing and first using the appliance,
read this user manual carefully,
including its hints and warnings. To
avoid unnecessary mistakes and
accidents, it is important to ensure that
all people using the appliance are
thoroughly familiar with its operation
and safety features. Save these
instructions and make sure that they
remain with the appliance if it is moved
or sold, so that everyone using it through
its life will be properly informed on
appliance use and safety.
General safety
• It is dangerous to alter the specifications or
attempt to modify this product in any way.
• This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use
of the appliance by a person responsible
for their safety.
• Make sure that small pets do not climb into
the drum. To avoid this, please check into
the drum before using.
• Any objects such as coins, safety pins,
nails, screws, stones or any other hard,
sharp material can cause extensive damage and must not be placed into the machine.
• In order to avoid danger of fires caused by
excessive drying, do not use appliance to
dry the following items: cushions, quilts
and the like (these items accumulate heat).
• Items such as foam rubber (latex foam),
shower caps, waterproof textiles, rubber
backed articles and clothes or pillows fitted with foam rubber pads should not be
dried in the tumble dryer.
• Always unplug the appliance after use,
clean and maintenance.
• Under no circumstances should you attempt to repair the machine yourself. Repairs carried out by inexperienced persons
may cause injury or serious malfunctioning. Contact your local Service Centre. Always insist on genuine spare parts.
electrolux 3
• Items that have been soiled with substances such as cooking oil acetone, petrol,
kerosene, spot removers, turpentine, waxes and wax removers should be washed in
hot water with an extra amount of detergent before being dried in the tumble dryer.
• Danger of explosion: never tumble dry
items that have been in contact with inflammable solvents (petrol, methylated
spirits, dry cleaning fluid and the like). As
these substance are volatile, they could
cause an explosion. Only tumble dry items
washed with water.
• Risk of fire: items that have been spotted
or soaked with vegetable or cooking oil
constitute a fire hazard and should not be
placed in the tumble dryer.
• If you have washed your laundry with stain
remover you must execute an extra rinse
cycle before loading your tumble dryer.
• Please make sure that no gas lighters or
matches have accidentally been left in
pockets of garments to be loaded into appliance
• When removing from the socket, never pull
the mains plug by the cable, instead take
a hold of the plug.
• The height adjustable screw feet must
never be removed.
• Manifold plugs, couplings and extension
cables must not be used. Risk of fire from
overheating!
• Do not spray down the appliance with jets
of water. Risk of electric shock!
• Do not lean on the open door. The appliance may tip over.
• Once the drying cycle or Iron Aid programme has been interrupted, the laundry
and drum may be hot. Risk of burns! Take
care when removing the laundry.
• Take care when interrupting the Iron Aid
programme: Do not open the machine
door during the steam phase. Hot steam
may result in burns. The display shows a
message to indicate the steam phase.
• The final part of a drying cycle occurs without heat (cool down cycle) to ensure that
the items are left at a temperature that ensures that the items will not be damaged.
•
Caution – Hot surface:
Do not touch the back of the appliance
while it is operating.
Warning! Never stop a tumble dry
before the end of the drying cycle
unless all items are quickly removed
and spread out so that the heat is
dissipated. Risk of fire!
• Risk of electric shock! Do not spray
down the appliance with jets of water.
Installation
• This appliance is heavy. Care should be
taken when moving it.
• When unpacking the appliance, check that
it is not damaged. If in doubt, do not use it
and contact the Service Centre.
• All packaging must be removed before
use. Serious damage can occur to the
product and to property if this is not adhered to. See relevant section in the user
manual.
• The final part of a tumble dryer cycle occurs without heat ( cool down cycle ) to
ensure that the items are left at a temperature that ensures that items will not be
damaged.
• Any electrical work required to install this
appliance should be carried out by a qualified electrician or competent person.
• Care must be taken to ensure that the appliance does not stand on the electrical
supply cable.
• If the machine is situated on a carpeted
floor, please adjust the feet in order to allow air to circulate freely under the appliance.
• After having installed the appliance, check
that it is not pressing or standing on its
electrical supply cable.
• If the tumble dryer is placed on top of a
washing machine, it is compulsory to use
the stacking kit (optional accessory).
Use
• The appliance is intended for drying and
steam treatment of standard laundry in domestic applications.
• This appliance is designed for domestic
use. It must not be used for purposes other
than those for which it was designed.
• Only dry fabrics which are designed to be
machine dried. Follow the instructions on
each garment label.
• Do not dry unwashed items in the tumble
dryer.
4 electrolux
• Do not overload the appliance. See the
relevant section in the user manual.
• Clothes which are dripping wet should not
be placed in the dryer.
• Garments which have been in contact with
volatile petroleum products should not be
machine dried. If volatile cleaning fluids are
used, care should be taken to ensure that
the fluid is removed from the garment before placing in the machine.
• When using dry-cleaning sets: only use
those products which are declared as suitable for the dryer by the manufacturer.
• Clean the micro-fine filter and fine strainer
after each drying cycle or Iron Aid programme.
• Do not use the machine without a lint filter
or with a damaged lint filter. Risk of fire!
• Only fill the water reservoir for steam treatment with distilled water. Do not use tap
water or any additives! The condensed
water from this appliance’s condensed
water container can also be used, if it is
filtered first (e. g. with a coffee filter).
• Clean the heat exchanger regularly.
• Never pull the power supply cable to remove the plug from the socket; always
take hold of the plug itself.
• Never use the tumble dryer if the power
supply cable, the control panel, the work-
•
•
•
•
ing surface or the base are damaged so
that the inside of the tumble dryer is accessible.
With stacked washer and Iron Aid appliance: do not place objects on the appliance. These may fall off during operation.
The lamp cover for the interior light must
be screwed down tightly.
Fabric softeners, or similar products
should be used as specified by the fabric
softener instructions.
Caution - hot surface : Do not touch the
door light cover surface when the light is
switched on.
Child safety
• This machine is not intended for use by
young children or infirm persons without
supervision.
• Children should be supervised to ensure
that they do not play with the appliance.
• The packaging components (e.g. plastic
film, polystyrene) can be dangerous to children - danger of suffocation! Keep them
out of children’s reach.
• Keep all detergents in a safe place out of
children’s reach.
• Make sure that children or pets do not
climb into the drum.
Environment
The symbol
on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it should be taken to the appropriate
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product. For more
detailed information about recycling of this
product, please contact your local council,
your household waste disposal service or the
shop where you purchased the product.
Old appliance
Warning!
Remove mains plug from socket when you
have no further use for the machine. Cut off
mains cable and dispose of together with
plug. Destroy loading door hook. Children
cannot then lock themselves in the machine
and put their lives at risk.
Packaging material
The packaging materials are environmentally
friendly and can be recycled. The plastic
components are identified by markings, e.g.
>PE<, >PS<, etc. Please dispose of the
packaging materials in the appropriate container at the community waste disposal facilities.
Environmental tips
• In the dryer, laundry becomes fluffy and
soft. Fabric softeners are not therefore
needed when washing.
electrolux 5
• Your dryer will function most economically
if you:
– always keep the ventilation slots on the
base of the dryer unobstructed;
– use the loading volumes specified in the
programme overview;
– ensure you have good ventilation in the
installation room;
– clean the micro-fine filter and fine strainer after each drying cycle;
– spin the laundry well before drying.
Energy consumption depends on spinning speed set in washing machine.
Higher spinning speed - lower energy
consumption.
Product description
1
6
7
8
2
9
10
3
11
4
12
5
13
14
1
2
3
4
5
6
Control panel
Fluff filters
Loading door (reversible)
Ventilation grille
Adjustable feet
Water recirculation valve/filter, Filler neck
for steam water tank
7 Drawer with condensed water container
8
9
10
11
12
13
14
Drum light
Drying rack
Push button for base door opening
Rating Plate
Heat exchanger
Drainage hose for water tank
Heat exchanger door
6 electrolux
Control panel
1
2
3
5
1
2
3
4
4
6
– FILTER
– CONTAINER
5 Function buttons
6 START/PAUSE button
Programme knob and On/Off switch
Display
DELAY TIMER button
Maintenance displays
– HEAT EXCHANGER
What is shown in the display
1
2
3 4 5 6 7
8
9 10 11 12 13 14 15
1
2
3
4
5
6
7
8
LOAD
DRYNESS
Start time preselection
Drying
Iron Aid programme
Cooling
Anticrease
Degree of dryness Display
9
10
11
12
13
14
15
Steam Filter indicator
DELICATE
Child safety device
Steam water tank indicator
BUZZER
Steam display
Start time /programme duration display
Before first use
In order to remove any residues which may
have been produced during production, wipe
the dryer drum with a damp cloth or carry out
a brief drying cycle (30 MIN) with damp cloths
in the machine.
1. Turn the programme knob to
TIME.
2. Press the TIME button repeatedly until
0.30 appears in the display.
3. Press the START/PAUSE button.
electrolux 7
Sorting and preparing laundry
Sorting laundry
• Sort by fabric type:
– Cotton/linen for programmes in
COTTONS programme group.
– Mixed fibres and synthetics for programmes in the
SYNTHETICS programme group.
Drying in the tumble
dryer possible in principle
Dry at normal temperature
Important! Do not place in the appliance any
wet laundry which is not specified on the care
label as being suitable for tumble-drying.
This appliance can be used for all wet laundry
items which are labelled as suitable for tumble-drying.
• Do not dry new, coloured textiles together
with light-coloured laundry items. Textile
colours may bleed.
• Do not dry cotton jersey and knitwear with
the EXTRA programme. Items may shrink!
• Wool and wool-like textiles can be dried
using the
WOOL programme. Before
the drying cycle spin the woollen textiles as
well as possible (max. 1200 rpm). Only dry
woollen textiles together which are similar
or the same with respect to material, colour and weight. Please dry heavy laundry
items made of wool separately.
Special notes about Iron Aid
Caution!
• The following textiles cannot be treated
using an Iron Aid programme: woollen
knitwear, leather, textiles with large metal,
wooden or plastic parts, textiles with rusting metal parts, oilskins or wax cotton garments.
• To smooth or freshen laundry with an Iron
Aid programme, sort laundry by size,
• Sorting by care label. The care labels
mean:
Dry at reduced temperature (press DELICATE
button!)
Drying in the tumble
dryer not possible
weight, material and colour. Only smooth
textiles together that are similar in terms of
size, weight, material and colour.
• Do not dry new, coloured textiles together
with light-coloured laundry items. Colours
may fade (check colour fastness of fabric
when damp in an inconspicuous area).
• Do not use dry cleaning sets such as dryel
in combination with Iron Aid programmes.
Preparing laundry
• To avoid laundry becoming tangled: close
zips, button up duvet covers and tie loose
ties or ribbons (e.g. of aprons).
• Empty pockets. Remove metal items (paper clips, safety pins, etc).
• Turn items with double-layered fabrics inside out (e.g. with cotton-lined anoraks,
the cotton layer should be outermost).
These fabrics will then dry better.
Special notes about Iron Aid
• Before treating garments with an Iron Aid
programme, remove stains by washing or
using localised stain removal.
• Turn items with double-layered fabrics inside out (e.g. with cottonlined anoraks, the
cotton layer should be outermost). These
fabrics will then dry better.
Starting up for the first time
Switching appliance on / switching light on.
Turn the programme selector to any programme. The appliance has been switched
on. When the loading door is opened, the
drum is illuminated. Opening loading door /
loading laundry
1. Open loading door: Push against the
loading door (push point )
8 electrolux
2. Load your laundry (do not force it in/ overload the machine).
Caution! Be careful not to trap laundry
in between the loading door and rubber
seal.
3. Close loading door securely. Lock must
audibly lock.
Iron AidTM Steam System
Fill water tank
You must fill up the water tank before using
an Iron Aid programme for the first time. Use
the distilled water provided if there is not yet
any condensed water from previous drying
programmes (see chapter on "Cleaning and
Maintenance, Emptying condensed water
container"). If, after an Iron Aid programme is
selected, the
water tank indicator on the
display lights up, you will need to fill up the
water tank with distilled water. Otherwise,
you will not be able to start any Iron Aid programme.
Caution! Important! Only fill the water
tank with distilled or fully desalinated
water. Do not use tap water or additives!
You can also use the condensed water
from the tank, as long as you filter it first
(use the canister supplied with the filter
fitted: see figure opposite).
1. Pull drawer containing condensed water
container out a little (1),
1
2. Push down the water tank’s filler neck (1)
and pull out it (2).
1
2
3. Fill with distilled water from the canister
provided, up to the MAX mark inside the
container.
electrolux 9
To activate recirculation set valve to the ON
position. To do that:
1. Pull drawer containing condensed water
container out a little (1). Behind the drawer there is water tank’s filler neck (2).
max
2
4. Push filler neck and drawer with condensed water container back in.
When dry, all textiles not specifically prohibited in the chapter ‘Sorting and preparing
laundry’ may be treated with the Iron Aid
Steam System. Wet textiles may only be treated if they are labelled as suitable for dry programmes.
1
2. Turn the valve to the ON position. Water
will be supplied by the water circuit directly to the steam water tank filling it automatically during the next drying cycle.
Water recirculation system
This system allows you to automatically use
for an Iron Aid Steam cycle the condensed
water collected in the condense water tank
during a drying cycle.
Caution! The water in the condense
water tank will never automatically fill the
steam water tank. The water
recirculation system works only if it is
supplied by water arising during
standard drying cycles.
To activate this system turn the valve to the
ON position. When the valve is ON the steam
water tank will be filled during the next drying
cycle. Water will be supplied by the water
circuit directly to the steam water tank filling
it automatically.
The steam water tank is empty. Please fill it
and then press START/PAUSE
If valve is closed (OFF position) recirculation system does not work.
Additional
functions / options
BUZZER
Application/properties
LOAD
Programmes
max. load
(weight when dry)
Overview of Iron Aid programmes
COTTON
1.0 kg
•
•
For 1- 6 cotton shirts. Min. 80% natural
fibres (cotton, linen etc).
wet,
dry
SYNTHETICS
1.0 kg
•
•
For 1- 6 synthetic shirts. Max. 20% natural fibres (cotton, linen etc).
wet,
dry
Additional
functions / options
BUZZER
Application/properties
LOAD
Programmes
max. load
(weight when dry)
10 electrolux
COTTON
3.0 kg
•
•
For smoothing cotton garments. Min.
80% natural fibres (cotton, linen etc).
wet,
dry
SYNTHETICS
1.5 kg
•
•
For smoothing easy-care garments.
Max. 20% natural fibres (cotton, linen
etc).
wet,
dry
REFRESH
2.5 kg
•
•
For one suit or up to two suit jackets or
pairs of trousers or similar garments. Also suitable for removing odours. For dry
garments only
All information on applications is for
guidance only. Smoothing results
may vary depending on the selected
programme and especially the fittings and material properties of the
textile. The results can be improved
if necessary by using different programmes and steam volumes. For
example, some textiles containing
more than 20% synthetics but with
the right fittings may behave more
like cotton textiles in an Iron Aid programme. You may therefore get better smoothing results by selecting a
cotton Iron Aid programme.
Given the wide range of different
textile grades and properties that
can be manufactured today using
different mechanical and chemical
processes, we recommend running
the first few Iron Aid programmes at
low steam levels and with a small
number of garments that are as similar as possible. Later, you can carefully start to vary the conditions of
Iron Aid programmes to learn from
experience how to get the best results from the volume of laundry loaded, the quality of the textiles and
the most suitable steam levels and
Iron AidTM programmes. Please also
note the accompanying ‘Textile
Guide’.
electrolux 11
Programme
COTTON
SYNTHETICS
COTTON
SYNTHETICS
REFRESH
LOAD
Loading volume
MIN
MED
MAX
1 - 2 shirts
MIN
MED
MAX
1 - 2 shirts
MIN
MED
MAX
0.5 - 1 kg
MIN
MED
MAX
0.2 - 0.5 kg
MIN
MED
MAX
1 pair of trousers
3 - 4 shirts
DURATION
dry [min.]1)
DURATION
wet [min.]1)
20-23
41-51
14-17
24-49
13-16
53-64
12-16
43-53
5 - 6 shirts
3 - 4 shirts
5 - 6shirts
1 - 2 kg
2 - 3 kg
0.5 - 1 kg
1 - 1.5 kg
1 jacket
12-16
1 suit
1) exact programme times appear in the display once the machine has performed wet/dry recognition
(approx. 2 min.)
All information provided on selecting the steam level and corresponding load are suggestions only. In
some cases, using a higher steam
level or smaller load may give better
results. The
REFRESH programme is a gentle Iron Aid programme for nonwashable textiles.
Any distortion to the shape of a garment which might occur in few cases, can be remedied by ironing.
Selecting the programme
Use the programme selector to set the programme you require. The estimated programme duration (in minutes) appears in the
multi-display.
Select steam level
(LOAD)
To achieve the best results, different steam
levels are required for different volumes of
laundry.
The LOAD button is used to set the required
steam level: MIN, MED or MAX.
All Iron Aid programmes, apart from the
REFRESH programme, automatically recognise the remaining dampness in clothes.
When laundry is wet, a drying cycle is activated first if required.
The table shows the steam levels appropriate
for the selected load, under LOAD.
1. Press the LOAD button repeatedly until
the desired steam level (MIN, MED or
MAX) is shown in the display.
If the LOAD button is not pressed after an
Iron Aid programme is selected, then medium steam level (MED) is selected automatically. If you select the
REFRESH programme, MIN is selected automatically.
12 electrolux
Important: If in doubt, always select a
lower steam level first until you have
more experience with load volumes, fabric types and the corresponding optimum steam level. If too high a steam
level is selected, garments may lose their
shape. If too low a steam level is selected, creases may remain.
Selecting additional functions
The additional functions available for the
Iron Aid programmes are BUZZER, DELAY
and the CHILD LOCK.
1. Select the programme and additional
functions.
2. Press the DELAY button as many times
as necessary until the required start delay
appears on the display, e.g.
if the programme is to be started in
12 hours.
3. To activate the delay timer, press the
START/PAUSE button. The amount of
time remaining until the programme is set
to start is continuously displayed (e.g.
,
,
,…
etc).
If the display is showing
and you press the button again, the
time delay will be cancelled. The display
will show
and then the duration of the
selected programme.
BUZZER
The appliance is supplied with the BUZZER
function activated. When the drying cycle
has finished, an intermittent acoustic signal
will sound. Each time a button is pressed or
a programme is changed using the programme knob, an audible signal is also set to
sound. The button is used to switch the function on or off. When the function is active, the
BUZZER
symbol appears in the display.
DELAY
With the DELAY button, you can delay
the start of a programme by between 30
minutes (
) and a maximum of 20 hours (
).
CHILD LOCK
The child lock can be set to prevent a programme being accidentally started or a programme in operation being accidentally
changed. The child safety device locks all
buttons and the programme knob. The child
safety device can be activated or deactivated
by holding down the BUZZER and TIME buttons simultaneously for 5 seconds.
• Before programme is started: Appliance
cannot be used
• After programme is started: Programme in
operation cannot be changed
The symbol
appears in the display to indicate that the child safety device is activated. The child safety device is not deactivated
once the programme comes to an end. If you
want to set a new programme, you must first
deactivate the child safety device.
Starting an Iron AidTM programme
Press the START/PAUSE button. The programme is started. First, the drying phase indicator appears in the display. The display
will also show the programme duration for
the selected Iron Aid programme, not including the additional drying phase. With wet
laundry, after a few minutes the appliance will
show the correct programme duration for the
Iron Aid programme including the preceding
drying programme. As soon as the right level
of dryness is reached, the Iron Aid programme will start automatically. The steam
indicator shows the progress of the Iron Aid
programme in the display. The individual
steam phases are shown by animated
clouds of steam.
Caution! Important: During the steam
phases that form part of the Iron Aid
programme and also the anti-crease
phase (represented by animated clouds
of steam in the display), the loading door
cannot be opened. Risk of burns!
electrolux 13
If the
water tank indicator lights up when
you select an Iron Aid programme, the programme cannot be started. You will need to
fill the water tank first (see section on ‘Cleaning and maintenance,filling water tank’.)
It is normal for the appliance to make
noises during an Iron Aid or drying programme if garments with hard parts,
such as metal buttons, are put in the
drum.
Changing a programme
To change a programme which has been selected by mistake once the programme has
started, first turn the programme selector to
O OFF and then reset the programme.
The programme can no longer be
changed directly once the programme
has started. If you nevertheless attempt
to change the programme with the programme knob or an additional function
button (except the BUZZER button), the
START/PAUSE button and
will
flash in the display. The drying programme is not however affected by this.
Putting in extra items or taking items out before end of programme
1. Open door.
2. Load or remove laundry items.
3. Close door securely.
4. Press the START/PAUSE button to continue the drying cycle.
Iron Aid programme complete /
removing laundry
After the Iron Aid phase has ended,
is illuminated and the icon
TICREASE appears in the display. If the
BUZZER has been activated, an audible signal sounds at regular intervals.
The Iron Aid programme is automatically
followed by an anti-crease phase, including brief steam phases, which lasts
around 90 minutes.
The drum rotates during the anti-crease
phase. This keeps the laundry loose and free
of creases. It can be removed at any point
during the anti-crease phase, except during
steam phases (look for steam animation in
the display!). Laundry should be removed as
quickly as possible.
1. Open the loading door to remove the
laundry.
2. Before removing the laundry, remove fluff
from the micro-fine filter. It is best to use
a damp hand for this purpose. (See
“Cleaning and maintenance” section.)
3. Remove laundry one garment at a time.
4. Turn the programme knob to O OFF.
Important! After each drying cycle
– Clean the micro-fine filter and fine filter
– Drain the condensed water container
(See section “Cleaning and maintenance”.)
5. Close door.
Caution! To retain the effects of the Iron
Aid treatment, clothes must be removed
one garment at a time during the anticrease phase and hung immediately on
a clothes hanger to dry (for at least 5-15
mins, depending on fabric and selected
steam level). Do up the buttons and tug
the garment into shape, paying particular attention to cuffs and seams.
AN-
Drying
COTTON
Care symbols
Application/properties
TIME
DRYNESS
DELICATE
Additional
functions /
options
BUZZER
max. load
(weight when dry)
Programmes
Overview of drying programmes
14 electrolux
DELICATE
DRYNESS
TIME
7 kg
•
•
•
-
Thorough drying of thick or multilayered fabrics,
e.g. terry towelling items, bathrobes.
CUPBOARD
7 kg
•
•
•
-
Thorough drying of fabrics of even thicknesses,
e.g. terry towelling items, knitwear, towels.
DAMP
7 kg
•
•
•
-
For normal thickness cotton or linen laundry, e.g.
bedding, table linen .
Care symbols
BUZZER
EXTRA
Programmes
max. load
(weight when dry)
Additional
functions /
options
Application/properties
SYNTHETICS
EXTRA
3 kg
•
•
•
-
Thorough drying of thick or multilayered fabrics,
e.g. pullovers, bedding, table linen.
CUPBOARD
3 kg
•
•
•
-
For thin fabrics which are not ironed e.g. easy care
shirts, table linen, baby clothes, socks, lingerie with
bones or wires.
DAMP
3 kg
•
•
•
-
For thin textiles which are still to be ironed, e.g.
knitted items, shirts.
•
For further drying of individual items of laundry or
for small volumes of less than 1kg. You can select
a programme duration from 10 mins to 3 hrs in 10minute steps.
TIME
TIME
7 kg
•
•
-
SPECIAL
SILK
WOOL
& SPORT
SHOES (with
RACK)
1 kg
1 kg
•
•
a
u
t
o
a
u
t
o
•
-
-
Special programme for drying silk using warm air
and gentle movement. .
•
For drying woollen fabrics after they have been
washed, using warm air at minimum mechanical
load (Follow section “Sorting and preparing washing”). Recommendation: Remove fabrics immediately after drying, as no anticrease programme follows.
For gentle drying of one pair of sport shoes, washed and spindried at 1000 rpm.
You can select a programme duration from 10
mins to 3 hrs in 10-minute steps.
1) Press the DELICATE button.
Selecting the programme
Use the programme selector to set the programme you require. The estimated programme duration (in minutes) appears in the
multi-display.
1)
1)
1)
electrolux 15
level MIN, MED or MAX. In the case of a drying cycle with relatively dry laundry, the length
of the programme cycle displayed at the beginning is corrected after a while.
Caution! Make sure that by selecting
the DRYNESS function, you do not overdry your wool or silk.
Selecting additional functions
You can choose from the additional functions
DRYNESS, DELICATE, BUZZER and TIME (if
a TIME programme has been selected). The
symbols of the functions available for the selected programme are shown in the display.
DRYNESS
If laundry comes out of the machine too
damp after a standard drying programme,
you can increase the drying result by using
the DRYNESS function. Laundry becomes
drier as you move from MIN to MAX.
1. Press the DRYNESS button repeatedly
until the desired dryness level (MIN, MED
or MAX) is shown in the display. If another
programme has been selected, AUTO
flashes in the display.
If wool or silk comes out of the machine too
damp at the end of a
WOOL or
SILK
programme, you can dry it again by restarting
the appropriate programme, this time with
the DRYNESS function selected and dryness
DELICATE
For especially gentle drying of sensitive fabrics with the care label and for temperaturesensitive textiles (e.g. acrylic, viscose). Programme is executed with reduced heat.
DELICATE is only suitable for use with loads
of up to 3kg.
1. Press the DELICATE button. The DELICATE symbol appears in the display.
TIME
To select the programme duration after setTIME programme. You can select
ting the
a programme duration from 10 minutes to 3
hours in 10-minute steps. (corresponding to
the
COOLING programme).
1. Turn the programme knob to the
TIMED PROGRAMME. The
minutes is in the display
2. Press the TIME button repeatedly until
the desired programme duration is
shown in the display, e.g.
for a programme of 20 minutes.
If the programme duration is not selected,
the duration is automatically set to 10 mins.
BUZZER
See chapter "Iron AidTM Steam System" ,
section "Selecting additional functions BUZZER"
DELAY
See chapter "Iron AidTM Steam System" ,
section "Selecting additional functions - DELAY"
CHILD LOCK
See chapter "Iron AidTM Steam System" ,
section "Selecting additional functions CHILD LOCK"
Starting a drying programme
Press the START/PAUSE button. The programme is started. The programme progress
display shows drying progress. The symbols
DRYING and
COOLING appear in
for
the display one after the other. The number
of droplets in the dryness indicator gradually
goes down as the drying process progresses.
16 electrolux
Changing a programme
To change a programme which has been selected by mistake once the programme has
started, first turn the programme selector to
O OFF and then reset the programme.
The programme can no longer be
changed directly once the programme
has started. If you nevertheless attempt
to change the programme with the programme knob or an additional function
button (except the BUZZER button), the
START/PAUSE button and
will
flash in the multi-display. The drying programme is not however affected by this.
Removing laundry or loading laundry
when necessary
Warning! Laundry and drumcan become hot. Risk of burns!
1. Open loading door
2. Load or remove laundry items.
3. Close the door securely. Lock must audibly lock.
4. Press the START/PAUSE button to continue the drying cycle.
If the
BUZZER is activated, an audible
signal sounds at regular intervals.
The drying cycle is automatically followed by a anti-crease phase which
lasts around 30 minutes.
The drum rotates at intervals during this
phase. This keeps the laundry loose and free
of creases. It can be removed at any time
during the anti-crease phase. (The laundry
should be taken out towards the end of the
anti-crease phase at the latest to prevent
creases from forming.)
1. Open door.
2. Before removing the laundry, remove fluff
from the micro-fine filter. It is best to use
a damp hand for this purpose. (See
“Cleaning and maintenance” section.)
3. Remove laundry.
4. Turn the programme knob to O OFF.
5. Important! After each drying cycle
– Clean the micro-fine filter and fine filter
– Drain the condensed water container
(See section “Cleaning and maintenance”.)
6. Close door.
Drying cycle complete / removing
laundry
Once the drying programme has finished,
CREASE GUARD lights up in the display.
Drying rack
The drying rack offers the possibility of drying
washable woollen fabrics and sports shoes.
The drying rack does not turn with the
clothes-dryer drum. This allows the drying of
woollen garments or sports shoes.
When wet, the wool must be moved as little
as possible because it tends to become matted, so drying rack is a solution.
Sports shoes cannot be dried without the
rack otherwise can damage the drum due to
their weight.
Lift the rack horizontally in the drum.
Guide the rack down until the support
bracket at the front rests on the opening.
For first unpacking of the rack please refer to the installation chapter.
Warning! Before installing the rack
check the dryer drum. It must be
empty!
1. Open the loading door.
2. Insert the rack.
3. Place the washing on the rack:
electrolux 17
– Spread the garment out in the rack and
roll it up, without squashing or folding
it.
– Place sport shoes on the rack.
4. Select the required programme run time,
selectable with an interval of 10 min, from
30 min. up to 180 minutes.
Press the TIME button as many times as
necessary until the required programme
running time is shown in the display.
5. Press the START/PAUSE button. The
programme is started.
6. At the end of the drying programme open
the loading door and remove the garments or shoes.
7. Turn the programme selector to O OFF.
8. Remove the rack from the drum at the
end of drying.
Important! Take out the insoles and place
them beside the shoes on the rack. Tie the
shoelaces.
Cleaning and maintenance
Cleaning lint filters
To ensure that the appliance works perfectly,
the lint filters in the door and in front of the
drum must be cleaned after every Iron
AidTM or drying cycle.
Caution! Important. Never operate the
dryer without the lint filter or with a
damaged or blocked lint filter.
1. Open loading door
2. Use a damp hand to clean the micro- fine
filter, which is built into the lower part of
the loading aperture.
18 electrolux
3. After a period of time, a patina due to detergent residue on laundry forms on the
filters. When this occurs, clean the filters
with warm water using a brush. Remove
the filter from the door pulling it out. It can
be positioned with the tooth facing to the
left or to the right). After cleaning do not
forget to put it back.
1
2
2. Clean the valve/filter under warm water.
4. Remove fluff from lint filter, preferably using a damp hand for this purpose.
5. Replace the filter.
3. Re-insert the valve/filter.
4. Turn the valve/filter in ON position.
Cleaning the water recirculation valve/
filter
STEAM FILTER symbol is shown in
If the
the display, the recirculation filter needs to be
cleaned. The valve/filter is placed behind the
tank handle - see chapter "Product description".
1. Push down the water tank’s filler neck (1)
and pull out it (2).
Clean the door seal
Wipe the door seal using a damp cloth immediately after the Iron Aid or drying cycle.
Emptying the condensed water
container
Empty condensed water container after every drying cycle. If the condensed water container is full, an active programme will break
off automatically and the
icon display will
electrolux 19
light up. In order to continue the programme,
the condensed water container must first be
emptied.
remove any residues and small pieces of
fluff.
Warning! The condensed water is
not suitable for drinking or for
preparing foodstuffs.
1. Pull drawer containing condensed water
container all the way out (1) and pull up
the condensed water container’s drainage pipe as far as it will go (2).
2.
Using the attached canister to filter: Pour
the water out of the container straight
through the filter at the top of the canister.
1.
2. Pour out the condensed water into a basin or similar container.
3. Push drainage pipe in and refit condensed water container.
Cleaning heat exchanger
If the
HEAT EXCHANGER is displayed,
the heat exchanger needs to be cleaned.
Caution! Operating when the heat
exchanger is blocked with fluff can
damage the dryer. This also increases
energy consumption.
1. Open door.
2. Open door in plinth. To do this, press the
release button on the bottom of the door
aperture and open the door in the plinth
to the left.
If the programme has been interrupted as
a result of the condensed water container
being full: Press the START/PAUSE button to continue the drying cycle.
The condensed water container has a
volume of approx. 4 litres. This is sufficient for around 7 kg of laundry which
has previously been spun at 1000 revolutions/ minute.
4. The condensed water can be used as
distilled water, e.g. for steam irons. However, first filter the condensed water to
3. Clean fluff from the inside of the door and
the heat exchanger front chamber. Wipe
the door seal with a damp cloth.
4. Turn both lock washers inwards.
20 electrolux
8. Replace heat exchanger and lock into
place (turn both lock washers outwards
until they snap into place).
9. Close door in plinth.
The appliance will not operate if the
HEAT EXCHANGER indicator is still lit.
Caution! Never operate the dryer
without the heat exchanger.
Cleaning the drum
5. Use the handle to pull the heat exchanger
out of the base and carry it horizontally to
prevent any remaining water from spilling.
Caution! Do not use abrasives or steel
wool to clean the drum.
Lime in the water or cleaning agents may
form a barely visible lining on the inside
of the drum. The degree to which the
laundry has been dried is then no longer
detected reliably. The laundry is damper
than expected when removed from the
appliance.
Use a standard domestic cleaner (e.g. vinegar-based cleaner) to wipe down the inside
of the drum and drum ribs.
6. To empty the heat exchanger, hold vertically over a washing-up bowl.
Caution! Do not use sharp objects to
clean. The heat exchanger could
develop leaks.
7. Clean heat exchanger.
It is best to use a brush or to rinse thoroughly with a hand-held shower.
Clean control panel and housing
Caution! Do not use furniture cleaners
or aggressive cleaning agents to clean
the machine.
Use a damp cloth to wipe down the control
panel and housing.
What to do if ...
Troubleshooting by yourself
If during operation, the error code E plus
number or letter) appears on the multi-display: Switch the appliance off and on again.
Problem
Dryer does not work.
IronAid programme does
not start. the
water
tank indicator lights up.
Reset programme. Press the START/PAUSE
button. If the error appears again, please
contact the Customer Care Department,
stating the error code
Possible cause
Remedy
Mains plug is not plugged in or fuse Plug in at mains socket. Check fuse
is not working correctly.
in fuse box (domestic installation).
Loading door is open.
Close loading door.
Have you pressed the START/
PAUSE button?
Press the START/PAUSE button
again.
Water tank is empty.
Fill water tank.
Recirculation valve is closed (OFF
position)
Turn the recirculation valve to ON
position.
electrolux 21
After a IronAid programme, garments are
not sufficiently smooth.
Wrong programme selected (e.g.
SYNTHETICS instead of
COTTON).
Note the composition of the fabric.
Too low a LOAD level set.
Set a higher LOAD level.
Too many garments in machine, or
garments that are too different.
Load the machine with fewer garments, or only similar ones.
Clothes are not removed until the
anti-crease phase is finished.
Remove clothes quickly one at a
time from the machine as soon as
possible after the start of the anticrease phase.
Garments not hung on clothes
hangers and/or not tugged into
shape.
Hang garments on clothes hangers, do up buttons and tug garments into shape.
Reshape multi-layered garments by
Multi-layered garments tend to lose
ironing after they come out of the
their shape.
machine.
After a IronAid programme, there are no
creases left in the garments.
The IronAid programme has the ef- Iron creases in again after the Ironfect of smoothing garments.
Aid programme.
Drying results unsatisfactory.
Wrong programme selected.
Select a different programme the
next time you dry (see “Programme
overview” chapter).
Lint filters clogged.
Clean lint filters.
Fluff filter clogged.
Clean fluff filter.
Heat exchanger clogged with lint.
Clean heat exchanger.
Overloading of laundry.
Observe recommended loading
volumes.
Ventilation slots in base area covered up.
Uncover ventilation slots in base
area.
Residue on inside surface of drum
or drum ribs.
Clean inside surface of drum and
drum ribs.
Make an adjustment using the
DRYNESS function (see chapter ”Drying”)
Conductance of water at installation site differs from standard setting of machine.
Re-programme standard setting for
degree of drying (see ‘Programming options’ chapter).
When a button is pressed
- no reaction of the machine.
Drying protection. After the start of
the programme, the option can no
longer be set.
Turn the programme knob to OFF.
Set the programme again.
Drum light does not work.
Programme selector in OFF position.
Turn programme selector to any
programme.
Defective light bulb.
Replace light bulb (see next section).
Displayed programme
time changes erratically or
stays unchanged for a
long time.
Programme time is corrected autoAutomatic process; this is not a
matically depending on type and
machine fault.
volume of laundry and level of
dampness.
22 electrolux
Empty Condensed water container , then start programme with
START/PAUSE button.
Programme inactive,
CONTAINER display illuminated.
Condensed water container is full.
Drying cycle ends shortly
after programme starts.
ANTICREASE display
illuminated.
Select time programme or higher
Not enough washing loaded or
EXTRA instead
washing loaded is too dry for selec- drying level (e.g.
ted programme.
of
CUPBOARD).
Drying cycle lasts an unusually long time. Note:
After up to 5 hours the
Lint filter clogged.
drying cycle ends automatically (see ‘End of drying cycle’).
Clean lint filter.
Fluff filter clogged.
Clean fluff filter.
Load volume too big.
Reduce load volume.
Laundry insufficiently spun.
Laundry must be adequately spun.
Particularly high room temperature. Automatic process, there is no fault
Temporary switching off of the
with the appliance. If possible, lowcompressor to avoid overload.
er the room temperature.
Discoloration
Colour fastness of textiles.
Changing the bulb for interior lighting
Only use a special bulb which is designed
specially for dryers. The special bulb can be
obtained from your local Service Force centre.
Warning! When the appliance is
switched on, the interior lighting
switches itself off after 4 minutes when
the door is open.
Check colour fastness of textiles.
Only treat textiles together if they
are a similar colour.
1. Unscrew cover above the bulb (this can
be found directly behind the loading aperture, at the top; refer to “Description of
machine” section.)
2. Replace defective bulb.
3. Screw cover back down.
Check the correct positioning of o-ring gasket before screwing back the door light cover. Do not operate the dryer when missing oring gasket on door light cover.
Warning! Do not use standard bulbs!
These develop too much heat and may
damage the machine!
Warning! For safety reasons, the cover
must be screwed down tightly. If this is
not done, the dryer must not be
operated.
Warning! Before replacing the bulb,
disconnect the mains plug.
Technical data
This appliance conforms with the following EU Directives:
– 2006/95/EC dated 12.12.2006 Low Voltage Directive
– 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending Directive
92/31/EEC
– 93/68/EEC dated 22.07.1993 CE Marking Directive
Height x width x depth
85 x 60 x 58 cm
Drum volume
108 l
Depth with loading door open
109 cm
Height can be adjusted by
1.5 cm
electrolux 23
Weight when empty
Loading volume (depends on
approx. 46 kg
programme)1)
max. 7 kg
Voltage
240V
Required fuse
13A
Total power
2350
Energy efficiency class
B
Energy consumption (7 kg of cotton, predrained
at 1000 rpm) 2)
3,92
Use
Domestic
Permissible ambient temperature
+ 5°C to + 35°C
Consumption values
The consumption values have been established under standard conditions. They may deviate when
the machine is operated in domestic circumstances.
Programme
Energy consumption in kWh
COTTON CUPBOARD DRY2)
4,0 (7 kg load pre-drained at 800 rpm)
3,9 (7 kg load pre-drained at 1000 rpm)
3,6 (7 kg load pre-drained at 1400 rpm)
COTTON IRON DRY2)
3.3 (7 kg load pre-drained at 1000 rpm)
SYNTHETICS CUPBOARD DRY2)
1,3 (7 kg load pre-drained at 1200 rpm)
1) Different loading volume data may be needed in some countries as a result of different measuring
methods.
2) in accordance with EN 61121
Machine settings
Setting
Implementation
BUZZER permanent off
1. Turn the programme selector to any programme.
2. Press simultaneously the DRYNESS and DELICATE buttons
and hold down for approx. 5 seconds.
3. The buzzer is by default always off. You can use BUZZER button
to activate or deactivate sound but machine does not memorize
your selection.
Water hardness
Water contains, a variable
quantity of limestone and mineral salts of which quantities
vary according to geographical
locations thus varying its conductivity values.
Relevant variations of the conductivity of the water compared
to those prefixed by the factory
could slightly influence the residual humidity of the laundry at
the end of the cycle. Your dryer
allows you to regulate the sensitivity of the drying sensor
based on conductivity values of
the water.
1. Turn the programme selector to any programme.
2. Press simultaneously the DELICATE and START/PAUSE buttons and hold down for approx. 5 seconds. The current setting
is on the display:
–
low conductivity <300 micro S/cm
–
medium conductivity 300-600 micro S/cm
–
high conductivity >600 micro S/cm
3. Press the START/PAUSE button sequentially until you set desired level.
4. To memorize setting press simultaneously the the DELICATE
and START/PAUSE buttons or turn knob to O OFF position
24 electrolux
Hints for test institutes
Parameters possible to checked by the Test
Institutes:
• Energy consumption (corrected with final
humidity) during the cupboard dry cotton
cycle with nominal load.
• Energy consumption (corrected with final
humidity) during the cupboard dry cotton
cycle with half load.
• Final humidity (during cupboard dry cotton, iron dry cotton and cupboard dry easy
care)
• Condensation efficiency (corrected with final humidity) during cupboard dry cotton
cycle with nominal and half load
All the cycles have to be checked in accordance with EN 61121 (Tumble dryers for
household use – Methods for measuring the
performance).
Installation
Important! The appliance must be moved in
vertical position for transport.
Appliance positioning
• It is recommended that, for your convenience, the machine is positioned close to
your washing machine.
• The tumble dryer must be installed in a
clean place, where dirt does not build up.
• Air must be able to circulate freely all round
the appliance. Do not obstruct the front
ventilation grille or the air intake grilles at
the back of the machine.
• To keep vibration and noise to a minimum
when the dryer is in use, it should be
placed on a firm, level surface.
• Once in its permanent operating position,
check that the dryer is absolutely level with
the aid of a spirit level. If it is not, raise or
lower the feet until it is.
• The feet must never be removed. Do not
restrict the floor clearance through deeppile carpets, strips of wood or similar. This
might cause heat built-up which would interfere with the operation of the appliance.
Important!
The hot air emitted by the tumble dryer can
reach temperatures of up to 60°C. The appliance must therefore not be installed on
floors which are not resistant to high temperatures.
When operating the tumble dryer, the room
temperature must not be lower than +5°C
and higher than +35°C, as it may affect the
performance of the appliance.
Important! Should the appliance be moved,
it must be transported vertically.
Important! The appliance must not be
installed behind the lockable door, a sliding
door a door with a hinge on the opposite side
to that of the appliance.
Removing transport safety packaging
Caution!
Before use all parts of the transport packaging must be removed.
1. Open loading door
2. Pull off adhesive strips from inside machine on top of drum.
3. Remove foil hose and polystyrene padding from the machine.
electrolux 25
Electrical connection
Details on mains voltage, type of current and
the fuses required should be taken from the
rating plate. The rating plate is fitted near the
loading aperture (see “Product description”
chapter).
Connect the machine to an earthed socket,
in accordance with current wiring regulations.
Drying rack unpacking
Caution! Before use all packaging parts
and rack must be removed from the
drum
To unpack the rack:
1. Remove upper protection polystyrene
parts by pulling them.
1
The appliance is supplied with a 13 amp plug
fitted. In the event of having to change the
fuse in the plug supplied, a 13 amp ASTA
approved BS 1363/A fuse must be used.
4
1
2. Lift slightly rack handle (not to the end).
For easiest unpacking turn the rack
upside down
3. Take it carefully out of the drum.
3
Warning! The manufacturer declines
any responsibility for damage or
injury through failure to comply with
the above safety precautions.
Should the appliance power supply
cable need to be replaced, this must
be carried out by an authorised service engineer or a qualified electrician. .
2
4. Remove from the drum rest of packing
elements.
3
1
2
The wires in the mains lead are coloured in
accordance with the following code:
1 Blue - Neutral
2 cord clamp
3 Brown - Live
4 Green and Yellow - Earth
The wire coloured green and yellow must be
connected to the terminal marked with the
letter «E» or by the earth symbol
or coloured green and yellow.
The wire coloured blue must be connected
to the terminal «N» or coloured black.
The wire coloured brown must be connected
to the terminal marked «L» or coloured red.
26 electrolux
Upon completion there must be no cut, or
stray strands of wire present and the cord
clamp must be secure over the outer sheath.
Warning! A cut off plug inserted into
a 13 amp socket is a serious safety
(shock) hazard.
Ensure that the cut off plug is disposed of safely.
Warning! The power supply cable
must be accessible after installing
the machine.
Permanent connection
In the case of permanent connection it is
necessary that you install a double pole
switch between the appliance and the electricity supply (mains), with a minimum gap of
3 mm between the switch contacts and of a
type suitable for the required load in compliance with the current electrical regulations.
The switch must not break the yellow and
green earth cable at any point.
Special accessories
The following special accessories are available from your Electrolux Service Force Centre
or your specialist dealer:
Intermediate installation kits for stacked
washer and iron aid appliance:
These intermediate installation kits can be
used to arrange the iron aid appliance and an
automatic Electrolux washing machine
(60cm wide, front loading) as a space-saving
washer/iron aid stack. The automatic washing machine is at the bottom and the iron aid
appliance is at the top. Two versions can be
supplied:
• without stacker plate
• with extractable stacker plate
Read the manual supplied with the installation kit carefully.
Service
In the event of technical faults, please first
check whether you can remedy the problem
yourself with the help of the operating instructions - see chapter What to do if….
If you were not able to remedy the problem
yourself, please contact the Customer Care
Department or one of our service partners.
In order to be able to assist you quickly, we
require the following information:
– Model description
– Product number (PNC)
– Serial number (S No. is on rating plate stuck
to the product - to find it see chapter Product
description))
GB
– Type of fault
– Any error messages displayed by the appliance
So that you have the necessary reference
numbers from your appliance at hand, we
recommend that you write them in here:
Model description:
PNC:
S No:
IE Guarantee/Customer Service
GREAT BRITAIN & IRELAND
Standard guarantee conditions
We, Electrolux, undertake that if within 12
months of the date of the purchase this Electrolux appliance or any part thereof is proved
to be defective by reason only of faulty workmanship or materials, we will, at our option
repair or replace the same FREE OF
CHARGE for labour, materials or carriage on
condition that:
• The appliance has been correctly installed
and used only on the electricity supply stated on the rating plate.
• The appliance has been used for normal
domestic purposes only, and in accordance with the manufacturer's instructions.
• The appliance has not been serviced,
maintained, repaired, taken apart or tampered with by any person not authorised
by us.
• Electrolux Service Force Centre must undertake all service work under this guarantee
• Any appliance or defective part replaced
shall become the Company's property.
• This guarantee is in addition to your statutory and other legal rights.
electrolux 27
Exclusions
• Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or removable
parts of glass or plastic.
• Costs incurred for calls to put right an appliance which is improperly installed or
calls to appliances outside the United
Kingdom.
• Appliances found to be in use within a
commercial environment, plus those
which are subject to rental agreements.
• Products of Electrolux manufacturer that
are not marketed by Electrolux
Service and Spare Parts
In the event of your appliance requiring service, or if you wish to purchase spare parts,
please contact your local Service Force Centre by telephoning
0870 5 929 929
Your telephone call will be automatically routed to the Service Force Centre covering your
postcode area.
For the address of your local Service Force
Centre and further information about Service
Force, please visit the website at
www.serviceforce.co.uk
Before calling out an engineer, please ensure
you have read the details under the heading
"What to do if..."
When you contact the Service Force Centre
you will need to give the following details:
1. Your name, address and postcode.
2. Your telephone number.
3. Clear concise details of the fault.
4. The model and Serial number of the appliance (found on the rating plate).
5. The purchase date.
Please note a valid purchase receipt or guarantee documentation is required for in guarantee service calls.
Customer Care
For general enquiries concerning your Electrolux appliance, or for further information on
Electrolux products please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.electrolux.co.uk
Customer Care Department, Electrolux Major Appliances
Addington Way, Luton
Bedfordshire, LU4 9QQ
Tel:
Electrolux
08705 950 950 1)
AEGElectrolux
08705 350 350 1)
ZanussiElectrolux
08705 727 727 1)
1) Calls may be recorded for training purposes
For Customer Service in The Republic of
Ireland please contact us at the address
below:
Electrolux Group (Irl) Ltd
Long Mile Road, Dublin 12, Republic of Ireland
Tel: +353 (0)1 4090751
Email: service.eid@electrolux.ie
European Guarantee
This appliance is guaranteed by Electrolux in
each of the countries listed at the back of this
user manual, for the period specified in the
appliance guarantee or otherwise by law. If
you move from one of these countries to another of the countries listed, the appliance
guarantee will move with you subject to the
following qualifications:• The appliance guarantee starts from the
date you first purchased the appliance
which will be evidenced by production of a
valid purchase document issued by the
seller of the appliance.
• The appliance guarantee is for the same
period and to the same extent for labour
and parts as exists in your new country of
residence for this particular model or range
of appliances.
• The appliance guarantee is personal to the
original purchaser of the appliance and
cannot be transferred to another user.
• The appliance is installed and used in accordance with instructions issued by Electrolux and is only used within the home, i.e.
is not used for commercial purposes.
• The appliance is installed in accordance
with all relevant regulations in force within
your new country of residence.
The provisions of this European Guarantee
do not affect any of the rights granted to you
by law.
www.electrolux.com
136906520-01-04082008