advertisement
Getting Started
HP Notebook
© Copyright 2011 Hewlett-Packard
Development Company, L.P.
Bluetooth is a trademark owned by its proprietor and used by Hewlett-Packard
Company under license. Microsoft and
Windows are U.S. registered trademarks of
Microsoft Corporation. SD Logo is a trademark of its proprietor.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services.
Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Second Edition: May 2011
First Edition: May 2011
Document Part Number: 648118-002
Product notice
This guide describes features that are common to most models. Some features may not be available on your computer.
Software terms
By installing, copying, downloading, or otherwise using any software product preinstalled on this computer, you agree to be bound by the terms of the HP End User
License Agreement (EULA). If you do not accept these license terms, your sole remedy is to return the entire unused product (hardware and software) within 14 days for a refund subject to the refund policy of your place of purchase.
For any further information or for requesting a full refund of the computer, please contact your local point of sale (the seller).
Safety warning notice
WARNING!
To reduce the possibility of heat-related injuries or of overheating the computer, do not place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to come into contact with the skin or a soft surface, such as pillows or rugs or clothing, during operation.
The computer and the AC adapter comply with the user-accessible surface temperature limits defined by the International Standard for Safety of Information Technology Equipment (IEC 60950).
iii
iv Safety warning notice
Table of contents
v
vi
Pinching/Zooming ............................................................................. 28
vii
viii
1 Welcome
●
●
After you set up and register the computer, it is important to take the following steps:
● Connect to the Internet—Set up your wired or wireless network so that you can connect to the
Internet. For more information, refer to Networking on page 16 .
● Update your antivirus software—Protect your computer from damage caused by viruses. The software is preinstalled on the computer and includes a limited subscription for free updates. For more information, refer to the HP Notebook Reference Guide. For instructions on accessing this
guide, refer to Finding information on page 3 .
● Get to know your computer—Learn about your computer features. Refer to
Getting to know your computer on page 5
and Keyboard and pointing devices on page 21 for additional
information.
● Create recovery discs or a recovery flash drive—Recover the operating system and software to factory settings in case of system instability or failure. For instructions, refer to
Backup and recovery on page 38 .
● Find installed software—Access a list of the software preinstalled on the computer. Select
Start > All Programs. For details about using the software included with the computer, refer to the software manufacturer's instructions, which may be provided with the software or on the manufacturer's Web site.
1
What's new?
Beats Audio (select models only)
Beats Audio is an enhanced audio profile that provides a deep, controlled bass while maintaining a clear sound. Beats Audio is enabled by default.
▲ To increase or decrease the Beats Audio bass settings, press fn + b .
You can also view and control the bass settings through the Windows operating system. To view and control the bass properties:
Select Start > Control Panel > Hardware and Sound > Beats Audio.
The following table shows and describes the Beats Audio icons.
Icon Description
Indicates that Beats Audio is enabled.
Indicates that Beats Audio is disabled.
2 Chapter 1 Welcome
Finding information
The computer comes with several resources to help you perform various tasks.
Resources
Quick Setup poster
Getting Started
To access this guide:
Select Start > Help and Support > User Guides.
– or –
Select Start > All Programs > HP > HP
Documentation.
HP Notebook Reference Guide
To access this guide:
Select Start > Help and Support > User Guides.
– or –
Select Start > All Programs > HP > HP
Documentation.
Help and Support
To access Help and Support, select Start > Help and
Support.
NOTE: For country- or region-specific support, go to http://www.hp.com/support , select your country or region, and follow the on-screen instructions.
Regulatory, Safety, and Environmental Notices
To access this guide:
Select Start > Help and Support > User Guides.
– or –
Select Start > All Programs > HP > HP
Documentation.
For information about
● How to set up the computer
● Help to identify computer components
● Computer features
● How to connect to a wireless network
● How to use the keyboard and pointing devices
● How to replace or upgrade the hard drive and memory modules
● How to perform a backup and recovery
● How to contact customer support
● Computer specifications
● Power management features
● How to maximize battery life
● How to use the multimedia features of the computer
● How to protect the computer
● How to care for the computer
● How to update the software
● Operating system information
● Software, driver, and BIOS updates
● Troubleshooting tools
● How to access technical support
● Regulatory and safety information
● Battery disposal information
Finding information 3
Resources
Safety & Comfort Guide
To access this guide:
Select Start > Help and Support > User Guides.
– or –
Select Start > All Programs > HP > HP
Documentation.
– or –
Go to http://www.hp.com/ergo .
Worldwide Telephone Numbers booklet
This booklet is provided with your computer.
HP Web site
To access this Web site, go to http://www.hp.com/ support .
For information about
● Proper workstation setup, posture, health, and work habits
● Electrical and mechanical safety information
HP support telephone numbers
● Support information
● Ordering parts and finding additional help
● Software, driver, and BIOS updates
● Accessories available for the device
Warranty information Limited Warranty*
To access the warranty:
Select Start > Help and Support > User Guides >
View Warranty Information.
– or –
Select Start > All Programs > HP > HP
Documentation > View Warranty Information.
– or –
Go to http://www.hp.com/go/orderdocuments .
*You may find the expressly provided HP Limited Warranty applicable to your product located with the electronic guides on your computer and/or on the CD/DVD provided in the box. Some countries/regions may provide a printed HP Limited
Warranty in the box. In countries/regions where the warranty is not provided in printed format, you may request a printed copy at http://www.hp.com/go/orderdocuments or write to:
● North America: Hewlett-Packard, MS POD, 11311 Chinden Blvd, Boise, ID 83714, USA
● Europe, Middle East, Africa: Hewlett-Packard, POD, Via G. Di Vittorio, 9, 20063, Cernusco s/Naviglio (MI), Italy
● Asia Pacific: Hewlett-Packard, POD, P.O. Box 200, Alexandra Post Office, Singapore 911507
Please include your product number, warranty period (found on your serial number label), name, and postal address.
4 Chapter 1 Welcome
2 Getting to know your computer
●
●
●
●
●
●
●
5
Top
TouchPad
Component
(1)
(2)
(3)
(4)
(5)
(6)
TouchPad on/off button
TouchPad zone
Left TouchPad button
TouchPad accent light
Right TouchPad button
Description
● On: The TouchPad is off.
● Off: The TouchPad is on.
Turns the TouchPad on and off.
Moves the pointer and selects or activates items on the screen.
Functions like the left button on an external mouse.
Illuminates the TouchPad for visual comfort under dark conditions when the TouchPad is on.
Functions like the right button on an external mouse.
6 Chapter 2 Getting to know your computer
Lights
Component
(1)
(2)
(3)
(4)
(5)
(6)
(7)
Description
Caps lock light
Power light
Mute light
On: Caps lock is on.
● White: The computer is on.
● Blinking white: The computer is in the Sleep state.
● Off: The computer is off or in Hibernation.
● Amber: Computer sound is off.
Wireless light
● Off: Computer sound is on.
● White: An integrated wireless device, such as a wireless local area network (WLAN) device and/or a
Bluetooth® device, is on.
● Amber: All wireless devices are off.
● On: The TouchPad is off.
● Off: The TouchPad is on.
TouchPad accent light Illuminates the TouchPad for visual comfort under dark conditions when the TouchPad is on.
Fingerprint reader light (select models only) ● White: The fingerprint was read.
● Amber: The fingerprint was not read.
Top 7
Buttons, speakers, and fingerprint reader (select models only)
Component
(1)
(2)
(3)
(4)
Power button
Description
● When the computer is off, press the button to turn on the computer.
● When the computer is on, press the button briefly to initiate Sleep.
● When the computer is in the Sleep state, press the button briefly to exit Sleep.
● When the computer is in Hibernation, press the button briefly to exit Hibernation.
If the computer has stopped responding and Windows® shutdown procedures are ineffective, press and hold the power button for at least 5 seconds to turn off the computer.
To learn more about your power settings, select Start >
Control Panel > System and Security > Power Options, or refer to the HP Notebook Reference Guide.
Web browser button
Fingerprint reader (select models only)
Opens the default Web browser.
NOTE: Until you set up your Internet or network services, this button opens the Internet Connection Wizard.
Allows a fingerprint logon to Windows, instead of a password logon.
8 Chapter 2 Getting to know your computer
Keys
Component
(1)
(2)
(3) esc key fn key
Windows logo key
(4) b key
(5)
(6)
(7)
(8)
Windows applications key
Integrated numeric keypad num lock key
Action keys
Description
Displays system information when pressed in combination with the fn key.
Executes frequently used system functions when pressed in combination with the b key, the spacebar , or the esc key.
Displays the Windows Start menu.
Increases or decreases the Beats Audio bass settings
(select models only) when pressed in combination with the fn key.
Beats Audio is an enhanced audio profile that provides a deep, controlled bass while maintaining a clear sound.
Beats Audio is enabled by default.
You can also view and control the bass settings through the Windows operating system. To view and control the bass properties:
Select Start > Control Panel > Hardware and Sound >
Beats Audio.
Displays a shortcut menu for items beneath the pointer.
When the keypad has been enabled, the keys can be used like an external numeric keypad.
Alternates between the navigational and numeric functions on the integrated numeric keypad.
Execute frequently used system functions.
Top 9
Front
Component
(1) Digital Media Slot
(2) Speakers (2) (select models only)
Description
Supports the following digital card formats:
● Secure Digital (SD) Memory Card
● Secure Digital Extended Capacity (SDxC) Memory Card
● Secure Digital High Capacity (SDHC) Memory Card
● Ultra High Speed MultiMediaCard (UHS/MMC)
Produce sound.
10 Chapter 2 Getting to know your computer
Right side
(6)
(7)
(8)
Component
(1)
(2)
Optical drive
Optical drive light
(3)
(4)
Optical drive eject button
Power light
(5) Hard drive light
(9)
USB ports (2)
Security cable slot
Power connector
Description
Reads and writes (select models only) to an optical disc.
● Green: The optical drive is being accessed.
● Off: The optical drive is idle.
Ejects the optical disc.
● White: The computer is on.
● Blinking white: The computer is in the Sleep state.
● Off: The computer is off or in Hibernation.
● Blinking white: The hard drive is being accessed.
● Amber: HP ProtectSmart Hard Drive Protection has temporarily parked the hard drive.
NOTE: For information on HP ProtectSmart Hard
Drive Protection, refer to the HP Notebook Reference
Guide.
Connect optional USB devices.
Attaches an optional security cable to the computer.
NOTE: The security cable is designed to act as a deterrent, but it may not prevent the computer from being mishandled or stolen.
● White: The computer is connected to external power and the battery is fully charged.
● Amber: A battery is charging.
● Blinking amber: The battery has reached a low battery level, or there is a battery error. When a battery reaches a critical battery level, the battery light begins blinking rapidly.
Connects an AC adapter.
Right side 11
Left side
Component
(1)
(6)
(7)
(4)
(5)
(2)
(3)
Vent
External monitor port
HDMI port
RJ-45 (network) jack
USB ports (2)
Audio-in (microphone) jack
Audio-out (headphone) jacks (2)
Description
Enables airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.
Connects an external VGA monitor or projector.
Connects an optional video or audio device, such as a high-definition television, or any compatible digital or audio component.
Connects a network cable.
Connect optional USB devices.
NOTE: Depending on your computer model, your computer may be equipped with 2 USB 3.0 ports, which connect optional USB 3.0 devices and provide enhanced
USB power performance. USB 3.0 ports are also compatible with USB 1.0 and 2.0 devices.
Connects an optional computer headset microphone, stereo array microphone, or monaural microphone.
Produce sound when connected to optional powered stereo speakers, headphones, ear buds, a headset, or television audio.
WARNING!
To reduce the risk of personal injury, adjust the volume before putting on headphones, earbuds, or a headset. For additional safety information, refer to the
Regulatory, Safety, and Environmental Notices.
NOTE: When a device is connected to a headphone jack, the computer speakers are disabled.
12 Chapter 2 Getting to know your computer
Display
Component
(1)
(2)
(3)
(4)
WLAN antennas (2)*
Internal microphones (2)
Webcam light
Webcam
Description
Send and receive wireless signals to communicate with wireless local area networks (WLAN).
Record sound.
On: The webcam is in use.
Records video and captures still photographs.
To use the webcam, select Start > All Programs > CyberLink
YouCam > CyberLink YouCam.
*The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around the antennas free from obstructions. To see wireless regulatory notices, refer to the section of the Regulatory, Safety,
and Environmental Notices that applies to your country or region. These notices are located in Help and Support.
Display 13
Rear
Component
Vent
Description
Enables airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.
14 Chapter 2 Getting to know your computer
Bottom
Component
(1)
(2)
(3)
(4)
Battery bay
Battery release latch
Vents (6)
Hard drive bay, WLAN, and memory module compartments
Description
Holds the battery.
Releases the battery from the battery bay, and releases the hard drive/memory module compartment cover.
Enable airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool internal components and prevent overheating. It is normal for the internal fan to cycle on and off during routine operation.
Holds the hard drive, and contains the wireless LAN
(WLAN) device and the memory module slots.
CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless module authorized for use in the computer by the governmental agency that regulates wireless devices in your country or region. If you replace the module and then receive a warning message, remove the module to restore computer functionality, and then contact technical support through Help and Support.
Bottom 15
3 Networking
●
Using an Internet service provider (ISP)
●
Connecting to a wireless network
NOTE: Internet hardware and software features vary depending on computer model and your location.
Your computer may support one or both of the following types of Internet access:
● Wireless—For mobile Internet access, you can use a wireless connection. Refer to
Connecting to an existing WLAN on page 18
or
Setting up a new WLAN network on page 19 .
● Wired—You can access the Internet by connecting to a wired network. For information on connecting to a wired network, refer to the HP Notebook Reference Guide.
16 Chapter 3 Networking
Using an Internet service provider (ISP)
Before you can connect to the Internet, you must establish an ISP account. Contact a local ISP to purchase Internet service and a modem. The ISP will help set up the modem, install a network cable to connect your wireless computer to the modem, and test the Internet service.
NOTE: Your ISP will give you a user ID and password to access the Internet. Record this information and store it in a safe place.
The following features will help you set up a new Internet account or configure the computer to use an existing account:
● Internet Services & Offers (available in some locations)—This utility assists with signing up for a new Internet account and configuring the computer to use an existing account. To access this utility, select Start > All Programs > Online Services > Get Online.
● ISP-provided icons (available in some locations)—These icons may be displayed either individually on the Windows desktop or grouped in a desktop folder named Online Services. To set up a new Internet account or configure the computer to use an existing account, double-click an icon, and then follow the on-screen instructions.
● Windows Connect to the Internet Wizard—You can use the Windows Connect to the Internet
Wizard to connect to the Internet in any of these situations:
◦ You already have an account with an ISP.
◦ You do not have an Internet account and want to select an ISP from the list provided within the wizard. (The list of ISP providers is not available in all regions.)
◦ You have selected an unlisted ISP, and the ISP has provided you with information such as a specific IP address and POP3 and SMTP settings.
To access the Windows Connect to the Internet Wizard and instructions for using it, select
Start > Control Panel > Network and Internet > Network and Sharing Center.
NOTE: If you are prompted within the wizard to choose between enabling or disabling
Windows Firewall, choose to enable the firewall.
Connecting to a wireless network
Wireless technology transfers data across radio waves instead of wires. Your computer may be equipped with one or more of the following wireless devices:
● Wireless local area network (WLAN) device
● HP Mobile Broadband Module, a wireless wide area network (WWAN) device (select models only)
● Bluetooth device
For more information on wireless technology and connecting to a wireless network, refer to the
HP Notebook Reference Guide and information and Web site links provided in Help and Support.
Using an Internet service provider (ISP) 17
Connecting to an existing WLAN
1.
Turn on the computer.
2.
Be sure that the WLAN device is on.
3.
Click the network icon in the notification area, at the far right of the taskbar.
4.
Select a network to connect to.
5.
Click Connect.
6.
If required, enter the security key.
18 Chapter 3 Networking
Setting up a new WLAN network
Required equipment:
● A broadband modem (either DSL or cable) (1) and high-speed Internet service purchased from an Internet service provider (ISP)
● A wireless router (purchased separately) (2)
● Your new wireless computer (3)
NOTE: Some modems have a built-in wireless router. Check with your ISP to determine what type of modem you have.
The illustration shows an example of a completed WLAN network installation that is connected to the
Internet. As your network grows, additional wireless and wired computers can be connected to the network to access the Internet.
Connecting to a wireless network 19
Configuring a wireless router
For help in setting up a WLAN, refer to the information provided by your router manufacturer or your
ISP.
The Windows operating system also provides tools to help you set up a new wireless network. To use the Windows tools to set up your network, select Start > Control Panel > Network and Internet >
Network and Sharing Center > Set up a new connection or network > Set up a new network.
Then follow the on-screen instructions.
NOTE: It is recommended that you initially connect your new wireless computer to the router by using the network cable provided with the router. When the computer successfully connects to the
Internet, you can disconnect the cable, and then access the Internet through your wireless network.
Protecting your WLAN
When you set up a WLAN or access an existing WLAN, always turn on security features to protect your network from unauthorized access.
For information on protecting your WLAN, refer to the HP Notebook Reference Guide.
20 Chapter 3 Networking
4 Keyboard and pointing devices
●
●
21
Using the keyboard
Using the action keys
Action keys are customized actions that are assigned to specific keys at the top of the keyboard. The icons on the f1 through f4 and f6 through f12 keys represent the action key functions.
To use an action key, press and hold this key to activate the assigned function.
NOTE: The action key feature is enabled at the factory. You can disable this feature in Setup Utility.
If this feature is disabled in Setup Utility, you must press fn and an action key to activate the assigned function.
Icon f2 f3 f4 f8 f9 f10 f6 f7
Key f1
Description
Opens Help and Support, which provides information about your Windows operating system and computer, answers to questions and tutorials, and updates to your computer.
Help and Support also provides automated troubleshooting and links to support specialists.
Decreases the screen brightness level incrementally when you hold down this key.
Increases the screen brightness level incrementally when you hold down this key.
Switches the screen image among display devices connected to the system. For example, if a monitor is connected to the computer, pressing this key alternates the screen image from computer display to monitor display to simultaneous display on both the computer and the monitor.
Most external monitors receive video information from the computer using the external
VGA video standard. The switch screen image key can also alternate images among other devices that are receiving video information from the computer.
Plays the previous track of an audio CD or the previous section of a DVD or a BD.
Plays, pauses, or resumes a track of an audio CD or a section of a DVD or a BD.
Plays the next track of an audio CD or the next section of a DVD or a BD.
Decreases speaker volume incrementally when you hold down this key.
Increases speaker volume incrementally when you hold down this key.
22 Chapter 4 Keyboard and pointing devices
Icon Key f11 f12
Description
Mutes or restores speaker sound.
Turns the wireless feature on or off.
NOTE: This key does not establish a wireless connection. To establish a wireless connection, a wireless network must also be set up.
Using the hotkeys
A hotkey is a combination of the fn key (1) and either the esc key (2), the b key (3), or the spacebar
(4).
To use a hotkey:
▲ Briefly press the fn key, and then briefly press the second key of the hotkey combination.
Function Hotkey
Display system information.
fn + esc
Description
Displays information about system hardware components and the system BIOS version number.
Using the keyboard 23
Function
Control the bass settings
(select models only).
Hotkey fn + b
Turn the TouchPad accent light on or off.
fn + spacebar
Description
Increases or decreases the Beats Audio bass settings (select models only).
Beats Audio is an enhanced audio profile that provides a deep, controlled bass while maintaining a clear sound. Beats Audio is enabled by default.
You can also view and control the bass settings through the
Windows operating system. To view and control the bass properties:
Select Start > Control Panel > Hardware and Sound > Beats
Audio.
Turns the TouchPad accent light on or off when the TouchPad is on.
NOTE: The TouchPad accent light is turned on at the factory. To extend battery life, turn off the TouchPad accent light.
Using the keypad
The computer includes an integrated numeric keypad. The computer also supports an optional external numeric keypad or an optional external keyboard that includes a numeric keypad.
Using the integrated numeric keypad
(1)
Component num lock key
(2) Integrated numeric keypad
24 Chapter 4 Keyboard and pointing devices
Description
Alternates between the navigational and numeric functions on the integrated numeric keypad.
NOTE: The keypad function that is active when the computer is turned off remains on when the computer is turned back on.
Can be used like an external numeric keypad.
Using pointing devices
NOTE: In addition to the pointing devices included with your computer, you can use an external
USB mouse (purchased separately) by connecting it to one of the USB ports on the computer.
Setting pointing device preferences
Use Mouse Properties in Windows® to customize settings for pointing devices, such as button configuration, click speed, and pointer options.
To access Mouse Properties, select Start > Devices and Printers. Then right-click the device representing your computer, and select Mouse settings.
Using the TouchPad
To move the pointer, slide one finger across the TouchPad in the direction you want the pointer to go.
Use the left and right TouchPad buttons like the buttons on an external mouse.
Using pointing devices 25
Turning the TouchPad off and on
To turn the TouchPad off and on, quickly double-tap the TouchPad on/off button.
NOTE: The TouchPad light is off when the TouchPad is on.
Navigating
To move the pointer, slide one finger across the TouchPad in the direction you want the pointer to go.
26 Chapter 4 Keyboard and pointing devices
Selecting
Use the left and right TouchPad buttons like the corresponding buttons on an external mouse.
Using TouchPad gestures
The TouchPad supports a variety of gestures. To use TouchPad gestures, place two fingers on the
TouchPad at the same time.
NOTE: TouchPad gestures are not supported in all programs.
To view the demonstration of a gesture:
1.
Click the Show hidden icons icon in the notification area, at the far right of the taskbar.
2.
Right-click the Synaptics Pointing Device icon , and then click TouchPad Properties.
3.
Click a gesture to activate the demonstration.
To turn the gestures on and off:
1.
Click the Show hidden icons icon in the notification area, at the far right of the taskbar.
2.
Right-click the Synaptics Pointing Device icon , and then click TouchPad Properties.
3.
Select the check box next to the gesture that you want to turn on or off.
4.
Click Apply, and then click OK.
Using pointing devices 27
Scrolling
Scrolling is useful for moving up, down, or sideways on a page or image. To scroll, place two fingers slightly apart on the TouchPad, and then drag them across the TouchPad in an up, down, left, or right motion.
NOTE: Scrolling speed is controlled by finger speed.
NOTE: Two-finger scrolling is enabled at the factory.
Pinching/Zooming
Pinching allows you to zoom in or out on images or text.
● Zoom in by placing two fingers together on the TouchPad, and then moving them apart.
● Zoom out by placing two fingers apart on the TouchPad, and then moving them together.
NOTE: Pinching/zooming is enabled at the factory.
28 Chapter 4 Keyboard and pointing devices
5 Maintenance
●
Inserting or removing the battery
●
Replacing or upgrading the hard drive
●
Adding or replacing memory modules
29
Inserting or removing the battery
NOTE: For additional information on using the battery, refer to the HP Notebook Reference Guide.
To insert the battery:
1.
Turn the computer upside down on a flat surface, with the battery bay toward you.
2.
Align the battery (1) with the outer edge of the battery bay.
3.
Rotate the battery (2) into the battery bay until it is seated. The battery release latch automatically locks the battery into place.
To remove the battery:
CAUTION: Removing a battery that is the sole power source for the computer can cause loss of information. To prevent loss of information, save your work and initiate Hibernation or shut down the computer through Windows before removing the battery.
1.
Turn the computer upside down on a flat surface.
2.
Slide the battery release latch (1) to release the battery.
NOTE: The battery release latch automatically returns to its original position.
30 Chapter 5 Maintenance
3.
Pivot the battery (2) upward and remove it from the computer (3).
Replacing or upgrading the hard drive
CAUTION: To prevent information loss or an unresponsive system:
Shut down the computer before removing the hard drive from the hard drive bay. Do not remove the hard drive while the computer is on, in the Sleep state, or in Hibernation.
If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system.
Removing the hard drive
1.
Save your work and shut down the computer.
2.
Disconnect all external devices connected to the computer.
3.
Unplug the power cord from the AC outlet.
4.
Turn the computer upside down on a flat surface.
5.
Remove the battery from the computer.
NOTE:
For more information, refer to the previous section, Inserting or removing the battery on page 30
.
Replacing or upgrading the hard drive 31
6.
Slide the battery release latch (1) until the cover is released, and then lift up and remove the cover (2).
7.
Disconnect the hard drive cable (1) from the computer.
8.
Remove the 4 hard drive screws (2).
9.
Lift the hard drive (3) out of the hard drive bay.
32 Chapter 5 Maintenance
Installing a hard drive
1.
Insert the hard drive (1) into the hard drive bay.
2.
Replace the 4 hard drive screws (2).
3.
Connect the hard drive cable (3) to the computer.
4.
Replace the hard drive cover: a.
With the battery bay toward you, position the hard drive cover (1) at a 45-degree angle from the surface of the computer so that the tabs on the underside of the cover align with the matching slots on the computer.
b.
Gently press the hard drive cover (2) down, applying pressure to both the left and right edges of the cover, until it snaps into place.
5.
Replace the battery.
Replacing or upgrading the hard drive 33
6.
Turn the computer right-side up, and then reconnect external power and external devices.
7.
Turn on the computer.
34 Chapter 5 Maintenance
Adding or replacing memory modules
The computer has two memory module slots. The memory module slots are located on the bottom of the computer under the hard drive cover. The memory capacity of the computer can be upgraded by adding a memory module or replacing the existing memory module in one of the memory module slots.
WARNING!
To reduce the risk of electric shock and damage to the equipment, unplug the power cord and remove all batteries before installing a memory module.
CAUTION: Electrostatic discharge (ESD) can damage electronic components. Before beginning any procedure, ensure that you are discharged of static electricity by touching a grounded metal object.
To add or replace a memory module:
CAUTION: To prevent information loss or an unresponsive system:
Shut down the computer before adding or replacing memory modules. Do not remove a memory module while the computer is on, in the Sleep state, or in Hibernation.
If you are not sure whether the computer is off or in Hibernation, turn the computer on by pressing the power button. Then shut down the computer through the operating system.
1.
Save your work and shut down the computer.
2.
Disconnect all external devices connected to the computer.
3.
Unplug the power cord from the AC outlet.
4.
Turn the computer upside down on a flat surface.
5.
Remove the battery from the computer.
NOTE: For more information, refer to the section
Inserting or removing the battery on page 30 .
6.
Slide the battery release latch (1) until the cover is released, and then lift up and remove the cover (2).
Adding or replacing memory modules 35
7.
If you are replacing a memory module, remove the existing memory module: a.
Pull away the retention clips (1) on each side of the memory module.
The memory module tilts up.
b.
Grasp the edge of the memory module (2), and then gently pull the memory module out of the memory module slot.
CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module.
To protect a memory module after removal, place it in an electrostatic-safe container.
8.
Insert a new memory module:
CAUTION: To prevent damage to the memory module, hold the memory module by the edges only. Do not touch the components on the memory module.
a.
Align the notched edge (1) of the memory module with the tab in the memory module slot.
b.
With the memory module at a 45-degree angle from the surface of the memory module compartment, press the module (2) into the memory module slot until it is seated.
c.
Gently press the memory module (3) down, applying pressure to both the left and right edges of the memory module, until the retention clips snap into place.
CAUTION: To prevent damage to the memory module, be sure that you do not bend the memory module.
36 Chapter 5 Maintenance
9.
Replace the memory module compartment cover: a.
With the battery bay toward you, position the memory module compartment cover (1) at a
45-degree angle from the surface of the computer so that the tabs on the underside of the cover align with the matching slots on the computer.
b.
Gently press the cover (2) down, applying pressure to both the left and right edges of the cover, until it snaps into place.
10.
Replace the battery.
11.
Turn the computer right-side up, and then reconnect external power and external devices.
12.
Turn on the computer.
Adding or replacing memory modules 37
6 Backup and recovery
●
●
●
●
Backing up and recovering your information
Your computer includes tools provided by the operating system and HP to help you safeguard your information and restore it if ever needed.
This chapter provides information on the following topics:
● Creating a set of recovery discs or a recovery flash drive (HP Recovery Manager software feature)
● Performing a system restore (from the partition, recovery discs, or a recovery flash drive)
● Backing up your information
● Recovering a program or driver
38 Chapter 6 Backup and recovery
Restore
In the event of hard drive failure, to restore your system to its factory image you will need a set of recovery discs or a recovery flash drive that you can create using HP Recovery Manager. HP recommends that you use this software to create either a set of recovery discs or a recovery flash drive immediately after software setup.
If for some other reason you need to restore your system, this can be achieved using the HP
Recovery partition (select models only), without the need for recovery discs or a recovery flash drive.
To check for the presence of a recovery partition, click Start, right-click Computer, click Manage, and then click Disk Management. If the recovery partition is present, a Recovery drive is listed in the window.
CAUTION: HP Recovery Manager (partition or discs/flash drive) restores only software that was preinstalled at the factory. Software not provided with this computer must be reinstalled manually.
NOTE: Recovery discs have been included if your computer does not have a recovery partition.
Creating restore media
HP recommends that you create either a set of recovery discs or a recovery flash drive to be sure that you can restore your computer to its original factory state if the hard drive fails, or if for any reason you cannot restore using the recovery partition tools. Create these discs or the flash drive after setting up the computer for the first time.
NOTE: HP Recovery Manager allows the creation of only one set of recovery discs or one recovery flash drive. Handle these discs or the flash drive carefully and keep them in a safe place.
NOTE: If your computer does not include an integrated optical drive, you can use an optional external optical drive (purchased separately) to create recovery discs, or you can purchase recovery discs for your computer from the HP Web site. If you use an external optical drive, it must be connected directly to a USB port on the computer, not to a USB port on an external device, such as a
USB hub.
Guidelines:
● Purchase high-quality DVD-R, DVD+R, DVD-R DL, or DVD+R DL discs.
NOTE: Read-write discs, such as CD-RW, DVD±RW, double-layer DVD±RW, and BD-RE
(rewritable Blu-ray) discs, are not compatible with the HP Recovery Manager software.
● The computer must be connected to AC power during this process.
● Only one set of recovery discs or one recovery flash drive can be created per computer.
NOTE: If you are creating recovery discs, number each disc before inserting it into the optical drive.
● If necessary, you can exit the program before you have finished creating the recovery discs or recovery flash drive. The next time you open HP Recovery Manager, you will be prompted to continue the backup creation process.
To create a set of recovery discs or a recovery flash drive:
1.
Select Start > All Programs > HP > HP Recovery Manager > HP Recovery Media Creation.
2.
Follow the on-screen instructions.
Restore 39
Performing a system restore
HP Recovery Manager software allows you to repair or restore the computer to its original factory state. HP Recovery Manager works from recovery discs or a recovery flash drive, or from a dedicated recovery partition (select models only) on the hard drive.
NOTE: A system restore needs to be performed if the computer hard drive has failed or if all attempts to correct any functional computer issues fail. A system restore should be used as a final attempt to correct computer issues.
Note the following when performing a system restore:
● You can restore only the system that you have previously backed up. HP recommends that you use Recovery Manager to create either a set of recovery discs or a recovery flash drive as soon as you set up the computer.
● Windows has its own built-in repair features, such as System Restore. If you have not already tried these features, try them before using HP Recovery Manager.
● HP Recovery Manager restores only software that was preinstalled at the factory. Software not provided with this computer must be downloaded from the manufacturer's Web site or reinstalled from the disc provided by the manufacturer.
Restoring using the dedicated recovery partition (select models only)
When using the dedicated recovery partition, there is an option to back up pictures, music and other audio, videos and movies, recorded TV shows, documents, spreadsheets and presentations, e-mails, and Internet favorites and settings during this process.
To restore the computer from the recovery partition, follow these steps:
1.
Access HP Recovery Manager in either of the following ways:
● Select Start > All Programs > HP > HP Recovery Manager > HP Recovery Manager.
– or –
● Turn on or restart the computer, and then press esc while the “Press the ESC key for
Startup Menu” message is displayed at the bottom of the screen. Then, press f11 while the
“F11 (System Recovery)” message is displayed on the screen.
2.
Click System Recovery in the HP Recovery Manager window.
3.
Follow the on-screen instructions.
40 Chapter 6 Backup and recovery
Restoring using the restore media
1.
If possible, back up all personal files.
2.
Insert the first recovery disc into the optical drive on your computer or an optional external optical drive, and then restart the computer.
– or –
Insert the recovery flash drive into a USB port on your computer, and then restart the computer.
NOTE: If the computer does not automatically restart in HP Recovery Manager, the computer boot order needs to be changed.
3.
Press f9 at system bootup.
4.
Select the optical drive or the flash drive.
5.
Follow the on-screen instructions.
Changing the computer boot order
To change the boot order for recovery discs:
1.
Restart the computer.
2.
Press esc while the computer is restarting, and then press f9 for boot options.
3.
Select Internal CD/DVD ROM Drive from the boot options window.
To change the boot order for a recovery flash drive:
1.
Insert the flash drive into a USB port.
2.
Restart the computer.
3.
Press esc while the computer is restarting, and then press f9 for boot options.
4.
Select the flash drive from the boot options window.
Performing a system restore 41
Backing up and recovering your information
It is very important to back up your files and keep any new software in a safe place. As you add new software and data files, continue to create backups on a regular basis.
How completely you are able to recover your system depends on how recent your backup is.
NOTE: A recovery from your most recent backup needs to be performed if the computer has a virus attack or if any major system components fail. In order to correct computer issues, a recovery should first be attempted before a system restore is attempted.
You can back up your information to an optional external hard drive, a network drive, or discs. Back up your system at the following times:
● At regularly scheduled times
TIP: Set reminders to back up your information periodically.
● Before the computer is repaired or restored
● Before you add or modify hardware or software
Guidelines:
● Create system restore points using the Windows® System Restore feature, and periodically copy them to an optical disc or an external hard drive. For more information on using system restore points, refer to
Using Windows system restore points on page 44 .
● Store personal files in the Documents library and back up this folder periodically.
● Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your settings. The screen shot can be a time-saver if you have to re-enter your preferences.
To create a screen shot:
1.
Display the screen you want to save.
2.
Copy the screen image:
To copy only the active window, press alt + prt sc .
To copy the entire screen, press prt sc .
3.
Open a word-processing document, and then select Edit > Paste. The screen image is added to the document.
4.
Save and print the document.
42 Chapter 6 Backup and recovery
Using Windows Backup and Restore
Guidelines:
● Be sure that the computer is connected to AC power before you start the backup process.
● Allow enough time to complete the backup process. Depending on file sizes, it may take over an hour.
To create a backup:
1.
Select Start > Control Panel > System and Security > Backup and Restore.
2.
Follow the on-screen instructions to schedule and create a backup.
NOTE: Windows® includes the User Account Control feature to improve the security of the computer. You may be prompted for your permission or password for tasks such as installing software, running utilities, or changing Windows settings. Refer to Help and Support for more information.
Backing up and recovering your information 43
Using Windows system restore points
A system restore point allows you to save and name a snapshot of your hard drive at a specific point in time. You can then recover back to that point if you want to reverse subsequent changes.
NOTE: Recovering to an earlier restore point does not affect data files saved or e-mails created since the last restore point.
You also can create additional restore points to provide increased protection for your files and settings.
When to create restore points
● Before you add or modify software or hardware
● Periodically, whenever the computer is functioning optimally
NOTE: If you revert to a restore point and then change your mind, you can reverse the restoration.
Create a system restore point
1.
Select Start > Control Panel > System and Security > System.
2.
In the left pane, click System Protection.
3.
Click the System Protection tab.
4.
Follow the on-screen instructions.
Restore to a previous date and time
To revert to a restore point (created at a previous date and time), when the computer was functioning optimally, follow these steps:
1.
Select Start > Control Panel > System and Security > System.
2.
In the left pane, click System Protection.
3.
Click the System Protection tab.
4.
Click System Restore.
5.
Follow the on-screen instructions.
44 Chapter 6 Backup and recovery
7 Customer support
●
●
45
Contacting customer support
If the information provided in this user guide, in the HP Notebook Reference Guide, or in Help and
Support does not address your questions, you can contact HP Customer Support at: http://www.hp.com/go/contactHP
NOTE: For worldwide support, click Contact HP worldwide on the left side of the page, or go to http://welcome.hp.com/country/us/en/wwcontact_us.html
.
Here you can:
● Chat online with an HP technician.
NOTE: When technical support chat is not available in a particular language, it is available in
English.
● E-mail HP Customer Support.
● Find HP Customer Support worldwide telephone numbers.
● Locate an HP service center.
46 Chapter 7 Customer support
Labels
The labels affixed to the computer provide information you may need when you troubleshoot system problems or travel internationally with the computer:
● Serial number label—Provides important information, including the following:
Component
(1) Product name
(2)
(3)
(4)
(5)
Serial number (s/n)
Part number/Product number (p/n)
Warranty period
Model description
Have this information available when you contact technical support. The serial number label is affixed to the bottom of the computer.
● Microsoft® Certificate of Authenticity—Contains the Windows Product Key. You may need the
Product Key to update or troubleshoot the operating system. The Microsoft Certificate of
Authenticity is located on the bottom of the computer.
● Regulatory label—Provides regulatory information about the computer. The regulatory label is affixed inside the battery bay.
● Wireless certification label or labels (select models only)—Provide information about optional wireless devices and the approval markings of some of the countries or regions in which the devices have been approved for use. If your computer model includes one or more wireless devices, one or more certification labels are included with your computer. You may need this information when traveling internationally. Wireless certification labels are affixed to the bottom of the computer.
Labels 47
8 Specifications
●
●
48 Chapter 8 Specifications
Input power
The power information in this section may be helpful if you plan to travel internationally with the computer.
The computer operates on DC power, which can be supplied by an AC or a DC power source. The
AC power source must be rated at 100–240 V, 50–60 Hz. Although the computer can be powered from a standalone DC power source, it should be powered only with an AC adapter or a DC power source supplied and approved by HP for use with this computer.
The computer can operate on DC power within the following specifications.
Input power
Operating voltage and current
Rating
18.5 V dc @ 3.5 A – 65 W; 19 V dc @ 4.74 A – 90 W; or 18.5 V dc @ 6.5 A –
120 W
DC plug of external HP power supply
NOTE: This product is designed for IT power systems in Norway with phase-to-phase voltage not exceeding 240 V rms.
NOTE: The computer operating voltage and current can be found on the system regulatory label.
Input power 49
Operating environment
Factor
Temperature
Operating (writing to optical disc)
Nonoperating
Relative humidity (noncondensing)
Operating
Nonoperating
Maximum altitude (unpressurized)
Operating
Nonoperating
Metric
5°C to 35°C
-20°C to 60°C
10% to 90%
5% to 95%
-15 m to 3,048 m
-15 m to 12,192 m
U.S.
41°F to 95°F
-4°F to 140°F
10% to 90%
5% to 95%
-50 ft to 10,000 ft
-50 ft to 40,000 ft
50 Chapter 8 Specifications
Index
A action keys decrease screen brightness
audio-in (microphone) jack 12 audio-out (headphone) jacks 12
B
backing up customized window, toolbar,
and menu bar settings 42 personal files 42
buttons
C
caps lock light, identifying 7
Certificate of Authenticity label 47
components
D
DC plug of external HP power
Digital Media Slot, identifying 10
E
F
H hard drive
hard drive bay, identifying 15
hotkeys
description 23 display system information 23
I
integrated numeric keypad,
integrated webcam light,
internal microphones, identifying
J jacks
audio-in (microphone) 12 audio-out (headphone) 12 network 12
K
keyboard hotkeys, identifying 23
keys
action 9 b 9 esc 9 fn 9 num lock 9
L labels
Microsoft Certificate of
Authenticity 47 regulatory 47 serial number 47
Index 51
lights
caps lock 7 fingerprint reader 7
M memory module
memory module compartment
memory module compartment,
Microsoft Certificate of Authenticity
mouse, external
N
num lock key, identifying 9, 24
O
operating system
Microsoft Certificate of
optical drive eject button,
identifying 11 optical drive light, identifying 11 optical drive, identifying 11
P
pointing devices, setting
ports
power connector, identifying 11 power lights, identifying 7, 11
product name and number,
R recovering from the dedicated
recovering from the recovery
regulatory information
regulatory label 47 wireless certification labels 47
RJ-45 (network) jack, identifying
S
security cable slot, identifying 11
serial number 47 serial number, computer 47
slots
T
TouchPad
TouchPad accent light hotkey 24
TouchPad gestures
pinching 28 scrolling 28 zooming 28
traveling with the computer 47
U
V
W
webcam light, identifying 13 webcam, identifying 13
Windows applications key,
Windows logo key, identifying 9
wireless certification label 47
wireless module compartment,
wireless network (WLAN),
wireless network, connecting 17
wireless router, configuring 20
WLAN
Z
52 Index
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement