Projector

CP-DX351

User Manual

Thank you for purchasing this product.

Please read this manual before you operate your projector.

Save it for future reference.

Table of contents

Important safety instructions .......................2

Introduction......................4

Projector features ................................. 4

Shipping contents................................. 5

Projector exterior view......................... 6

Controls and functions ......................... 7

Positioning your projector..........................10

Choosing a location............................ 10

Projection dimensions ........................ 11

Connection ......................12

Connecting a computer or monitor .... 13

Connecting Video source devices ...... 14

Operation ........................17

Starting up the projector..................... 17

Using the menus................................. 18

Utilizing the password function ......... 19

Switching input signal........................ 21

Adjusting the projected image ........... 22

Magnifying and searching for details. 23

Selecting the aspect ratio ................... 24

Optimizing the image......................... 26

Setting the presentation timer ............ 29

Hiding the image................................ 30

Locking control keys.......................... 30

Freezing the image............................. 30

Operating in a high altitude environment ....................................... 31

Shutting down the projector............... 31

Menu operation .................................. 32

Maintenance ...................41

Care of the projector .......................... 41

Lamp information .............................. 42

Troubleshooting .............47

Specifications ..................48

Projector specifications...................... 48

Dimensions ........................................ 49

........................................................... 49

Timing chart ...................................... 50

Regulation Statements ...54

FCC statement ................................... 54

ICES-003 ........................................... 54

WEEE ................................................ 54

Copyright information...56

Warranty and afterservice..............................57

Entries and graphical symbols explanation

The following entries and graphical symbols are used for the manuals and the product as follows, for safety purpose. Please know their meanings beforehand, and heed them.

WARNING: This entry warns of a risk of serious personal injury or even death.

CAUTION: This entry warns of a risk of personal injury or physical damage.

1

Important safety instructions

Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product.

Safety Instructions

WARNING

1.

Please read this manual before you operate your projector. Save it for future reference.

2.

Do not look straight at the projector lens during operation. The intense light beam may damage your eyes.

3.

Refer servicing to qualified service personnel.

4.

In some countries, the line voltage is NOT stable. This projector is designed to operate safely within a mains voltage between 100 to 240 volts AC, but could fail if power cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate

or cut out, it is recommended that you connect your projector through a power stabilizer, surge protector or uninterruptible power supply (UPS).

5.

Do not block the projection lens with any objects when the projector is under operation as this could cause the objects to become heated and deformed or even cause a fire. To temporarily turn off the display, press

BLANK on the remote control.

6.

The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement.

7.

Never replace the lamp assembly or any electronic components unless the projector is unplugged.

8.

Do not place this product on an unstable cart, stand, or table. The product may fall, sustaining serious damage.

9.

Do not attempt to disassemble this projector. There are dangerous high voltages inside which may cause death if you should come into contact with live parts. The only user serviceable part is the lamp which has its own removable cover.

Under no circumstances should you ever undo or remove any other covers. Refer servicing only to suitably qualified professional service personnel.

10. Do not place this projector in any of the following environments.

- Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls and free flow of air around the projector.

- Locations where temperatures may become excessively high, such as the inside of a car with all windows rolled up.

- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shortening the projector's life span and darkening the picture.

- Locations near fire alarms

- Locations with an ambient temperature above 35°C / 95°F (The altitude is 1500 m~3050 m : Ambient temperature above 30°C / 86°F)

- Locations where the altitudes are higher than 3050 m (10007 feet).

11.

Do not block the ventilation holes. Otherwise the components inside the projector will become overheated and result in a fire or malfunction. In addition, do not place the

2

projector in locations near an air conditioner, fan or dryer because direct contact with constant heat or warm air may cause deformation to the outer casing of the projector.

- Do not place this projector on a blanket, bedding or any other soft surface.

- Do not cover this projector with a cloth or any other item.

- Do not place inflammables near the projector.

12. Always place the projector on a level, horizontal surface during operation.

- Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of more than 15 degrees front to back. Using the projector when it is not fully horizontal may cause a malfunction of, or damage to, the lamp.

13. Do not stand the projector on end vertically. Doing so may cause the projector to fall over, causing injury or resulting in damage to the projector.

14. Do not step on the projector or place any objects upon it. Besides probable physical damage to the projector, doing so may result in accidents and possible injury.

15. Do not place liquids near or on the projector. Liquids spilled into the projector may cause it to fail. If the projector does become wet, disconnect it from the power supply's wall socket and call your local service center to have the projector serviced.

16. When the projector is under operation, you may sense some heated air and odor from its ventilation grill. It is a normal phenomenon and not a product defect.

17. Do not use the security lock slot for transporting or installation. It should be used with a commercially available theft prevention cable.

3

Introduction

Projector features

The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use.

The projector offers the following features.

• Presentation timer for better control of time during presentations

• Supports 3D display

• Color Management allowing color adjustments to your liking

• Less than 0.5W power consumption when standby mode is saving

• Wall Color correction allowing projection on surfaces of several predefined colors

• Quick auto search speeding up the signal detecting process

• Multiple sets of preset modes providing choices for different projection purposes

• One-key auto-adjustment to display the best picture quality

• Digital keystone correction to correct distorted images

• Adjustable color management control for data/video display

• High brightness projection lamp

• Ability to display 1.07 billion colors

• Multi-language On-Screen Display (OSD) menus

• Switchable normal and economic modes to reduce the power consumption

• Component HDTV compatibility (YP b

P r

)

• The apparent brightness of the projected image will vary depending on the ambient lighting conditions, selected input signal contrast/brightness settings, and is directly proportional to projection distance.

• The lamp brightness will decline over time and may vary within the lamp manufacturers specifications. This is normal and expected behavior.

4

Shipping contents

Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase.

Standard accessories

The supplied accessories will be suitable for your region, and may differ from those illustrated.

Projector Power Cord VGA Cable

Multi-language user manual CD

User manual Remote Control & Battery

CU-TR Declaration

Optional accessories

1.

Replacement lamp: DT01853

2.

Ceiling mount: HAS-DX301

5

3

4

5

Projector exterior view

Front/upper side

1

2

6

7

8

9

10

Rear/lower side

13 16

12 14 17 18

19

20 21 22

AUDIO IN S-VIDEO

AUDIO OUT

VIDEO

HDMI

COMPUTER IN2 COMPUTER IN1 MONITOR OUT(1 ONLY)

SERVICE

CONTROL

11

15

5 23

23

24

1.

Control panel

(See

"Control panel" on page 7 for

details.)

2.

Lamp cover

3.

Vent (heated air exhaust)

4.

Projection lens

5.

Front elevator foot

6.

Zoom ring

7.

Focus ring

8.

Vent (cool air intake)

9.

Speaker

10. Front IR remote sensor

11.

AC power cord inlet

12. AUDIO OUT port

13. AUDIO IN port

14. S-VIDEO port

15. VIDEO port

16. HDMI port

17. COMPUTER IN2 port

18. COMPUTER IN1 port

19. MONITOR OUT port

20. SERVICE port

21. CONTROL port

22. Security lock slot

23. Rear elevator foot

24. Name tag bar

5

WARNING

• THIS APPARATUS MUST BE EARTHED.

• When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should occur during operation of the unit, operate the disconnect device to switch the power supply off, or disconnect the power plug.

6

Controls and functions

Control panel

1

2

7

8

3

4 9

5

10

6

3

1.

TEMPerature indicator light

Lights up red if the projector's temperature becomes too high.

2.

LAMP indicator light

Indicates the status of the lamp. Lights up or flashes when the lamp has developed a problem.

7.

POWER indicator light

Lights up or flashes when the projector is under operation.

8.

Toggles the projector between standby mode and on.

3.

4.

Keystone/Arrow keys (

Down)

Manually corrects distorted images resulting from an angled projection.

Left

Up,

Used to hide the screen picture.

5.

MODE/ENTER

Selects an available picture setup mode.

Enacts the selected On-Screen Display

(OSD) menu item.

6.

SOURCE

Displays the source selection bar.

9.

Right

Activates panel key lock.

When the On-Screen Display (OSD)

menu is activated, the #3, #4, and #9 keys

are used as directional arrows to select the desired menu items and to make adjustments.

10. MENU

Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings.

7

Remote control

1

4

5

6

7

2

3

8

11

12

13

14

7

9

10

1.

Toggles the projector between standby mode and on.

2.

MENU/EXIT

Turns on the On-Screen Display (OSD) menu. Goes back to previous OSD menu, exits and saves menu settings.

3.

FREEZE

Freezes the projected image.

4.

Left

5.

MODE/ENTER

Selects an available picture setup mode.

Enacts the selected On-Screen Display

(OSD) menu item.

6.

BLANK

Used to hide the screen picture.

7.

Keystone/Arrow keys ( Up,

Down)

Manually corrects distorted images resulting from an angled projection.

8.

VOLUME (+, -)

Adjusts the sound level.

15

9.

AUTO

Automatically determines the best picture timings for the displayed image.

10.

Right

Activates panel key lock.

When the On-Screen Display (OSD)

menu is activated, the #4, #7, and #10

keys are used as directional arrows to select the desired menu items and to make adjustments.

11.

SOURCE

Displays the source selection bar.

12. MAGNIFY (+, -)

Magnifies or reduces the projected picture size.

13. TIMER ON

Activates or displays an on-screen timer based on your own timer setting.

14. TIMER SET UP

Enters presentation timer setting directly.

15. Battery cover

8

Remote control effective range

The Infra-Red (IR) remote control is located on the front of the projector. The remote control must be held at an angle within 30 degrees perpendicular to the projector's

IR remote control sensor to function correctly. The distance between the remote control and the sensor should not exceed 4 meters (~ 13 feet).

Make sure that there are no obstacles between the remote control and the IR sensor on the projector that might obstruct the infra-red beam.

Remote control function may not work correctly, if the strong light or light from the inverter fluorescent lamp hits sensor window.

Replacing the remote control battery

1.

Pull out the battery holder.

Please follow the illustrated instructions. Push and hold the locking arm while pulling out the battery holder.

15º

15º

4m

(approx.)

2.

Insert the new battery in the holder. Note the positive polarity should face outward.

3.

Push the holder into the remote control.

WARNING

Improper use may result in battery explosion, cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment. If you observe battery leakage, wipe out the leakage and then replace a battery.

If the leakage adheres to your body or clothes, rinse well with water immediately.

• Keep the battery away from children and pets. Be careful for them not to swallow a battery.

• Avoid leaving the remote control and battery in an excessive heat or humid environment like the kitchen, bathroom, sauna, sunroom or in a closed car.

• Replace only with the same or equivalent type recommended by the battery manufacturer: [type: CR2025]

• Dispose of the used battery according to the manufacturer's instructions and local environment regulations for your region.

• Never throw the battery into a fire. There may be danger of an explosion.

• If the battery is dead or if you will not be using the remote control for an extended period of time, remove the battery to avoid damage to the remote control from possible battery leakage.

• Do not recharge, short circuit, solder or disassemble a battery.

9

Positioning your projector

Choosing a location

Your room layout or personal preference will dictate which installation location you select.

Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment.

Your projector is designed to be installed in one of following possible installation locations:

1.

Normal

Select this location with the projector placed near the floor in front of the screen. This is the most common way to position the projector for quick setup and portability.

2.

H Invert

Select this location with the projector placed near the floor behind the screen.

Note that a special rear projection screen is required.

Set H Invert in the SYSTEM SETTING: BASIC

> Mirror menu after you turn the projector on.

3.

V Invert

Select this location with the projector suspended upside-down from the ceiling behind the screen.

Note that a special rear projection screen is required.

Set V Invert in the SYSTEM SETTING: BASIC

> Mirror menu after you turn the projector on.

4.

H & V Invert

Select this location with the projector suspended upside-down from the ceiling in front of the screen.

Set H & V Invert in the SYSTEM SETTING:

BASIC > Mirror menu after you turn the projector on.

10

Projection dimensions

Refer to "Dimensions" on page 49 for the center of lens dimensions of this projector before

calculating the appropriate position.

The "screen" mentioned below refers to the projection screen usually consisting of a surface and a support structure.

Zoom Ratio: 1.1 x a:

Screen size

(Diagonal) type

(inch) m

60

70

80

90

100

120

150

200

250 m b: Projection distance min.

inch m max.

4:3 screen inch cm c1:

Screen height inch c2:

Screen height cm inch

2.0 3.2 125 3.5 138 122 48 -12 -5

2.3 3.6 141 3.9 155 137 54 -14 -5

2.5 4.0 156 4.4 172 152 60 -15 -6

3.0 4.8 188 5.2 207 183 72 -18 -7

3.8 6.0 235 6.6 258 229 90 -23 -9

5.1 7.9 313 8.7 344 305 120 -30 -12

6.4 9.9 391 10.9 430 381 150 -38 -15 a:

Screen size

(Diagonal) type

(inch) m b: Projection distance

16:9 screen c1:

Screen height c2:

Screen height m min.

inch m max.

inch cm inch cm inch

60

70

80

90

100

120

150

2.0 3.5 136 3.8 150 133 52 -33 -13

2.3 3.9 153 4.3 169 150 59 -37 -15

2.5 4.3 171 4.8 188 166 65 -42 -16

3.0 5.2 205 5.7 225 199 78 -50 -20

200

250

3.8 6.5 256 7.1 281 249 98 -62 -25

5.1 8.7 341 9.5 375 332 131 -83 -33

• There is 3% tolerance among these numbers due to optical component variations. It is recommended that if you intend to permanently install the projector, you should physically test the projection size and distance using the actual projector in situ before you permanently install it, so as to make allowance for this projector's optical characteristics. This will help you determine the exact mounting position so that it best suits your installation location.

• To obtain the clearest image possible, we suggest that you keep the desired image size within 60" to 180".

11

Connection

When connecting a signal source to the projector, be sure to:

1.

Turn all equipment off before making any connections.

2.

Use the correct signal cables for each source.

3.

Ensure the cables are firmly inserted.

• In the connections shown below, some cables may not be included with the projector (see

"Shipping contents" on page 5 ). They are commercially available from electronics stores.

• The connection illustrations below are for reference only. The rear connecting ports available on the projector vary with each projector model.

•

For detailed connection methods, see pages 13-16.

Speakers

(with an amplifier)

Computer

AUDIO

OUT HDMI RGB OUT

R L

AUDIO IN S-VIDEO

AUDIO OUT

VIDEO

HDMI

COMPUTER IN2 COMPUTER IN1 MONITOR OUT(1 ONLY)

SERVICE

CONTROL

Monitor

VCR/DVD/Blu-ray Disc

TM

player

AUDIO

OUT

R

L VIDEO

AUDIO

R

OUT

L

S-VIDEO

HDMI

AUDIO

R

OUT

L

COMPONENT

Y Cb/Pb Cr/Pr

AUDIO IN S-VIDEO

AUDIO OUT

VIDEO

HDMI

COMPUTER IN2 COMPUTER IN1

MONITOR OUT(1 ONLY)

SERVICE

CONTROL

12

Connecting a computer or monitor

Connecting a computer

The projector provides two VGA input sockets that allow you to connect them to both

IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are connecting legacy version Macintosh computers.

To connect the projector to a notebook or desktop computer:

1.

Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer.

2.

Connect the other end of the VGA cable to the COMPUTER IN1 or COMPUTER

IN2 signal input socket on the projector.

Many notebooks do not turn on their external video ports when connected to a projector.

Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press

FN and the labeled function key simultaneously. Refer to your notebook's documentation to find your notebook's key combination.

Connecting a monitor

If you want to view your presentation close-up on a monitor as well as on the screen, you can connect the MONITOR OUT signal output socket on the projector to an external monitor with a VGA cable following the instructions below:

To connect the projector to a monitor:

1.

Connect the projector to a computer as described in

"Connecting a computer" on page

13

.

2.

Take a suitable VGA cable (only one supplied) and connect one end of the cable to the

D-Sub input socket of the video monitor.

Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable and connect the DVI end of the cable to the DVI input socket of the video monitor.

3.

Connect the other end of the cable to the MONITOR OUT socket on the projector.

The MONITOR OUT output only works when COMPUTER IN1 connection is made to the projector.

13

Connecting Video source devices

You can connect your projector to various Video source devices that provide any one of the following output sockets:

• HDMI

• Component Video

• S-Video

• Video (composite)

You need only connect the projector to a Video source device using just one of the above connecting methods, however each provides a different level of video quality. The method you choose will most likely depend upon the availability of matching terminals on both the projector and the Video source device as described below:

Best video quality

The best available video connection method is HDMI. If your source device is equipped with a HDMI socket, you can enjoy uncompressed digital video quality.

See "Connecting an HDMI device" on page 15

for how to connect the projector to a HDMI source device and other details.

If no HDMI source is available, the next best video signal is Component video (not to be confused with composite video). Digital TV tuner and DVD players output Component video natively, so if available on your devices, this should be your connection method of choice in preference to (composite) video.

See "Connecting a Component Video source device" on page 15 for how to connect the

projector to a component video device.

Better video quality

The S-Video method provides a better quality analog video than standard composite Video.

If you have both composite Video and S-Video output terminals on your Video source device, you should elect to use the S-Video option.

See "Connecting an S-Video source device" on page 16 for how to connect the projector to

an S-Video device.

Least video quality

Composite Video is an analog video and will result in a perfectly acceptable, but less than optimal result from your projector, being the least video quality of the available methods described here.

See

"Connecting a composite Video source device" on page 16

for how to connect the projector to a composite Video device.

Connecting audio

The projector has one built-in mono speaker which is designed to provide basic audio functionality accompanying data presentations for business purposes only. It is not designed for, nor intended for stereo audio reproduction use as might be expected in home theater or home cinema applications. Any stereo audio input (if provided), is mixed into a common mono audio output through the projector speaker.

If you wish, you can make use of the projector (mixed mono) speaker in your presentations, and also connect separate amplified speakers to the Audio Out socket of the projector. The audio output is a mixed mono signal and controlled by the projector Volume and Mute settings.

14

If you have a separate sound system, you will most likely want to connect the audio output of your Video source device to that sound system, instead of to the mono audio projector.

• The audio output only works when a signal source is connected to the projector.

• When an audio cable is connected to the AUDIO OUT port, the projector’s speaker will be muted.

Connecting an HDMI device

You should use an HDMI cable when making connection between the projector and HDMI devices.

To connect the projector to an HDMI device:

1.

Take an HDMI cable and connect one end to the HDMI output port of the video device.

2.

Connect the other end of the cable to the HDMI input port on the projector.

The projector is only capable of playing mixed mono audio. See

"Connecting audio" on page

14 for details.

Connecting a Component Video source device

Examine your Video source device to determine if it has a set of unused Component Video output sockets available:

• If so, you can continue with this procedure.

• If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to a Component Video source device:

1.

Take a VGA (D-Sub)-Component adaptor cable and connect the end with 3 RCA type connectors to the Component Video output sockets of the Video source device. Match the color of the plugs to the color of the sockets; green to green, blue to blue, and red to red.

2.

Connect the other end of the VGA (D-Sub)-Component adaptor cable (with a D-Sub type connector) to the COMPUTER IN1 or COMPUTER IN2 socket on the projector.

• The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See

"Connecting audio" on page 14 for details.

• If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

15

Connecting an S-Video source device

Examine your Video source device to determine if it has an unused S-Video output socket available:

• If so, you can continue with this procedure.

• If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to an S-Video source device:

1.

Take an S-Video cable and connect one end to the S-Video output socket of the Video source device.

2.

Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.

• The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See

"Connecting audio" on page 14 for details.

• If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

• If you have already made a Component Video connection between the projector and this

S-Video source device using Component Video connections, you need not connect to this device using an S-Video connection as this makes an unnecessary second connection of poorer picture quality. See

"Connecting Video source devices" on page 14

for details.

Connecting a composite Video source device

Examine your Video source device to determine if it has a set of unused composite Video output sockets available:

• If so, you can continue with this procedure.

• If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to a composite Video source device:

1.

Take a Video cable and connect one end to the composite Video output socket of the

Video source device.

2.

Connect the other end of the Video cable to the VIDEO socket on the projector.

• The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See

"Connecting audio" on page 14 for details.

• If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

• You need only connect to this device using a composite Video connection if Component

Video and S-Video inputs are unavailable for use. See

"Connecting Video source devices" on page 14

for details.

16

Operation

Starting up the projector

1.

Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch

(where fitted).

AUDIO IN

S-VIDE

2.

Press on the projector or remote control to start the projector. The POWER indicator light stays blue when the projector is on.

(If necessary) Rotate the focus ring to adjust the image clearness.

AUDIO OUT

VIDEO

• If the projector is still hot from previous activity, it will run the cooling fan for approximately 60 seconds before energizing the lamp.

• To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before turning it off.

• Also, do not turn the projector on for about 10 minutes or more after turning off.

3.

If the projector is activated for the first time, select your OSD language and High Altitude

Mode following the on-screen instructions.

Language

See "Using the menus" on page 18

for details.

High Altitude Mode

See "Operating in a high altitude environment" on page 31 for details.

4.

Switch all of the connected equipment on.

5.

The projector will start to search for input signals. The current input signal being scanned appears in the upper left corner of the screen. If the projector doesn't detect a valid signal, the message 'No Signal' will continue to be displayed until an input signal is found.

You can also press SOURCE on the projector or remote control to select your desired

input signal. See "Switching input signal" on page 21 for details.

• If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the message 'Out of Range' displayed on a blank screen. Please change to an input signal which is compatible with the projector's resolution or set the input signal to a lower setting. See

"Timing chart" on page 50

for details.

• OSD languages and user manual languages may not match.

17

Using the menus

The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings.

The OSD screenshots below are for reference only, and may differ from the actual design.

Below is the overview of the OSD menu.

Main menu icon

Highlight

Sub-menu

Current input signal

Wall Color

Aspect Ratio

Keystone

Position

Phase

H. Size

Magnify

3D Sync

3D Sync Invert

Analog RGB

15

15

Off

Auto

Disable

MENU Exit

Status

Go to the previous page or to exit.

To use the OSD menus, please set them to your familiar language first.

1.

Press MENU on the projector or

MENU/EXIT on the remote control to turn the OSD menu on.

3.

Press highlight and press MODE/ENTER.

Wall Color

Aspect Ratio

Keystone

Position

Phase

H. Size

Magnify

3D Sync

3D Sync Invert

Analog RGB

15

15

Off

Auto

Disable

MENU Exit

Presentation Timer

Language

Mirror

Auto Power Off

Blank Timer

Panel Key Lock

Sleep Timer

Background Color

Analog RGB

ENTER

Normal

30 min

Disable

Off

Disable

Original

MENU Exit

2.

Use / to highlight the SYSTEM

SETTING: Basic menu.

Presentation Timer

Language

Mirror

Auto Power Off

Blank Timer

Panel Key Lock

Sleep Timer

Background Color

Analog RGB

English

Normal

30 min

Disable

Off

Disable

Original

MENU

Exit

4.

Press / / / to select a preferred language and press

MODE/ENTER.

5.

Press MENU on the projector or

MENU/EXIT on the remote control to leave and save the settings.

: DISPLAY

: PICTURE

: SOURCE

: SYSTEM SETTING: Basic

: SYSTEM SETTING: Advanced

: INFORMATION

18

Utilizing the password function

For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display

(OSD) menu. For details of the OSD menu operation, please refer to

"Using the menus" on page 18 .

You will be inconvenienced if you activate the password functionality and subsequently forget the password. Print this user manual (if necessary) and write the password you used in this manual, and keep it in a safe place for later use.

Setting a password

1.

Open the OSD menu and go to the SYSTEM SETTING: Advanced > Security

Settings menu. Press MODE/ENTER on the projector or remote control. The

Security Settings page is displayed.

2.

Highlight Change Password and press MODE/ENTER.

3.

As pictured to the right, the four arrow keys

INPUT NEW PASSWORD

( , , , ) respectively represent 4 digits (1,

2, 3, 4). According to the password you desire to set, press the arrow keys to enter six digits for the password.

4.

Confirm the new password by re-entering the new password.

Once the password is set, the OSD menu returns to the Security Settings page.

MENU

Back

5.

To activate the Power on Lock function, press / to highlight Power on Lock and press / to select On. When the Power on Lock function is activated, you have to enter the correct password to turn on the projector.

6.

To leave the OSD menu, press MENU on the projector or MENU/EXIT on the remote control.

• Once a password has been set, the projector cannot be used unless the correct password is entered every time the projector is started.

• The digits being input will be displayed as asterisks on-screen. Write your selected password down here in this user manual in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __ __

Keep this user manual in a safe place.

If you forget the password

If the password function is activated, you will be asked to enter the six-digit password every time you turn on the projector. If you enter the wrong password, the password error message as pictured to the right is

Password Error

Please try again.

displayed lasting for three seconds, and the message

'INPUT PASSWORD' follows. You can retry by entering another six-digit password, or if you did not record the password in this user manual, and you absolutely do not remember it, you can use

the password recall procedure. See "Entering the password recall procedure" on page 20

for details.

If you enter an incorrect password 5 times in succession, the projector will automatically shut down in a short time.

19

Entering the password recall procedure

1.

Press and hold AUTO on the remote control for 3 seconds. The projector will display a coded number on the screen.

2.

Write down the number and turn off your projector.

3.

Seek help from the local dealer to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector.

RECALL PASSWORD

Please write down the recall code, and contact the dealer.

Recall Code:

XXX XXX XXX XXX

MENU

Exit

Changing the password

1.

Open the OSD menu and go to the SYSTEM SETTING: Advanced > Security

Settings > Change Password menu.

2.

Press MODE/ENTER on the projector or remote control. The message 'INPUT

CURRENT PASSWORD' is displayed.

3.

Enter the old password.

• If the password is correct, another message 'INPUT NEW PASSWORD' is displayed.

• If the password is incorrect, the password error message is displayed lasting for three seconds, and the message 'INPUT CURRENT PASSWORD' is displayed for your retry. You can press MENU on the projector or MENU/

EXIT on the remote control to cancel the change or try another password.

4.

Enter a new password.

5.

Confirm the new password by re-entering the new password.

6.

You have successfully assigned a new password to the projector. Remember to enter the new password next time the projector is started.

7.

To leave the OSD menu, press MENU on the projector or MENU/EXIT on the remote control.

The digits being input will be displayed as asterisks on-screen. Write your selected password down here in this user manual in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __ __

Keep this user manual in a safe place.

20

Disabling the password function

To disable password protection, go back to the SYSTEM SETTING: Advanced >

Security Settings > Power on Lock menu after opening the OSD menu system. Select Off by pressing / . The message 'INPUT PASSWORD' is displayed. Enter the current password.

•

• If the password is correct, the OSD menu returns to the Security Settings page with 'Off' shown in the row of Power on Lock. You will not have to enter the password next time you turn on the projector.

If the password is incorrect, the password error message is displayed lasting for three seconds, and the message 'INPUT PASSWORD' is displayed for your retry. You can press MENU on the projector or MENU/EXIT on the remote control to cancel the change or try another password.

Though the password function is disabled, you need to keep the old password in hand should you ever need to re-activate the password function by entering the old password.

Switching input signal

The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time.

Be sure the Quick Auto Search function in the SOURCE menu is On if you want the projector to automatically search for the signals.

You can also manually select the desired signal by pressing one of the source selection keys on the remote control, or cycle through the available input signals. Once you have done this, the Quick Auto Search function will be turned off automatically.

1.

Press SOURCE on the projector or remote control. A source selection bar is displayed.

2.

Press / until your desired signal is selected and press MODE/ENTER on the projector or remote control.

Once detected, the selected source information will be displayed on the screen for

seconds. If there are multiple devices connected to the projector, repeat steps 1-2 to

search for another signal.

• The brightness level of the projected image will change accordingly when you switch between different input signals. Data (graphic) "computer" presentations using mostly static images are generally brighter than "Video" using mostly moving images (movies).

•

The input signal type effects the options available for the Preset Mode. See "Selecting a preset mode" on page 26 for details.

• Please see

"Projector specifications" on page 48 for the native display resolution of this

projector. For best display picture results, you should select and use an input signal which outputs at this resolution. Any other resolutions will be scaled by the projector depending upon the 'aspect ratio' setting, which may cause some image distortion or loss

of picture clarity. See "Selecting the aspect ratio" on page 24

for details.

21

Adjusting the projected image

Adjusting the projection angle

The projector is equipped with two adjuster feet.

They change the image height and vertical projection angle. Screw the adjuster feet to fine tune the angle until the image is positioned where you want it.

If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image becomes trapezoidal. To correct this situation,

see "Correcting keystone" on page 23 for

details.

CAUTION

Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes.

Be careful when you screw the front adjuster foot as it is close to the exhaust vent where hot air comes from.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press AUTO on the remote control or activate the Auto Adjustment function in the SOURCE menu. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of

Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the upper left corner of the screen for 3 seconds.

• The screen will be blank while AUTO is functioning.

• This function is only available when computer signal (analog RGB) is selected.

Fine-tuning the image clarity

1.

Adjust the projected image to the size that you need using the zoom ring.

2.

If necessary, sharpen the image by rotating the focus ring.

FOCUS ring

ZOOM ring

22

Correcting keystone

Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen.

To correct this, besides adjusting the height of the projector, you will need to manually correct it following one of these steps.

• Press / on the projector or remote control to display the Keystone correction page. Press

to correct keystoning at the top of the image. Press to correct keystoning at the bottom of the image.

Press

/

Press

/

• Using the OSD menu

1.

Press MENU on the projector or MENU/EXIT on the remote control and then press

/ until the

DISPLAY

menu is highlighted.

2.

Press to highlight Keystone and press MODE/ENTER on the projector or remote control. The Keystone correction page is displayed.

3.

Press to correct keystoning at the top of the image or press to correct keystoning at the bottom of the image.

Magnifying and searching for details

If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys for navigating the picture.

• Using the remote control

1.

Press Magnify + /Magnify - on the remote control to display the Zoom bar.

2.

Press Magnify + on the remote control or on the projector repeatedly to magnify the picture to a desired size.

3.

To navigate the picture, press the directional arrows ( , , , ).

4.

To reduce size of the picture, press Magnify - on the remote control, or on the projector. You can also restore the picture to its original size by pressing the AUTO button on the remote control.

• Using the OSD menu

1.

Press MENU on the projector or MENU/EXIT on the remote control and then press

/ until the DISPLAY menu is highlighted.

2.

Press to highlight Magnify and press MODE/ENTER on the projector remote control. The Zoom bar is displayed.

3.

Repeat steps 2-4 in the section of Using the remote control

above.

The picture can only be navigated after the picture is magnified. You can further magnify the picture while searching for details.

23

Selecting the aspect ratio

The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio.

With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal.

To change the projected image ratio (no matter what aspect the source is):

1.

Press MENU on the projector or MENU/EXIT on the remote control and then press

/ until the DISPLAY menu is highlighted.

2.

Press to highlight Aspect Ratio.

3.

Press / to select an aspect ratio to suit the format of the video signal and your display requirements.

24

About the aspect ratio

In the pictures below, the black portions are inactive areas and the white portions are active areas. OSD menus can be displayed on those unused black areas.

1.

Auto: Scales an image proportionally to fit the projector's native resolution in its horizontal width. This is suitable for the incoming image which is neither in 4:3 nor 16:9 and you want to make most use of the screen without altering the image's aspect ratio.

16:10 picture

15:9 picture

2.

Real: The image is projected as its original resolution, and resized to fit within the display area. For input signals with lower resolutions, the projected image will display smaller than if resized to full screen. You could adjust the zoom setting or move the projector towards the screen to increase the image size if necessary. You may also need to refocus the projector after making these adjustments.

4:3 picture

16:9 picture

3.

4:3: Scales an image so that it is displayed in the center of the screen with a 4:3 aspect ratio. This is most suitable for 4:3 images like computer monitors, standard definition TV and 4:3 aspect

DVD movies, as it displays them without aspect alteration.

4:3 picture

4.

16:9: Scales an image so that it is displayed in the center of the screen with a 16:9 aspect ratio.

This is most suitable for images which are already in a 16:9 aspect, like high definition TV, as it displays them without aspect alteration.

16:9 picture

25

Optimizing the image

Selecting a preset mode

The projector is preset with several predefined preset modes so that you can choose one to suit your operating environment and input signal picture type.

To select an operation mode that suits your need, you can follow one of the following steps.

• Press MODE/ENTER on the projector or remote control repeatedly until your desired mode is selected.

• Go to the PICTURE > Preset Mode menu and press / to select a desired mode.

The preset modes available for different types of signals are listed below.

1.

Bright mode: Maximizes the brightness of the projected image. This mode is suitable for environments where extra-high brightness is required, such as using the projector in well lit rooms.

2.

Presentation mode: Is designed for presentations under daylight environment to match computer and notebook computer coloring.

3.

sRGB mode: Maximizes the purity of RGB colors to provide true-to-life images regardless of brightness setting. It is most suitable for viewing photos taken with an sRGB compatible and properly calibrated camera, and for viewing computer graphic and drawing applications.

4.

Cinema mode: Is appropriate for playing colorful movies, video clips from digital cameras or DVs through the computer input for best viewing in a blackened (little light) environment.

5.

Game mode: Suitable for all types of entertainment media, including gaming and movies.

6.

User mode: Recalls the settings customized based on the current available preset modes. See

"Setting the User mode" on page 26

for details.

Setting the User mode

1.

Press MENU on the projector or MENU/EXIT on the remote control to open the On-

Screen Display (OSD) menu.

2.

Go to the PICTURE > Preset Mode menu.

3.

Press / to select User. The adjustments you make in the Brightness, Contrast,

Color, Tint, Sharpness, Brilliant Color, Color Temperature and 3D Color

Management will automatically be saved as the User mode.

Fine-tuning the image quality in user modes

According to the detected signal type, there are some user-definable functions available when User mode is selected. You can make adjustments to these functions based on your needs.

Adjusting Brightness

Highlight the PICTURE > Brightness menu and press / .

The higher the value, the brighter the image. And the lower the setting, the darker the image. Adjust this control so the black areas of the image appear just as black and that detail in the dark areas is visible.

+0

+50 +100

26

Adjusting Contrast

Highlight the PICTURE > Contrast menu and press / .

The higher the value, the greater the contrast. Use this to set the peak white level after you have previously adjusted the Brightness setting to suit your selected input and viewing environment.

Adjusting Color

Highlight the PICTURE > Color menu and press / .

-50

0 +50

Lower setting produces less saturated colors. If the setting is too high, colors on the image will be overpowering, which makes the image unrealistic.

This function is only available when a Video, S-Video or Component Video signal is selected.

Adjusting Tint

Highlight the PICTURE > Tint menu and press / .

The higher the value, the more reddish the picture becomes. The lower the value, the more greenish the picture becomes.

This function is only available when a Video, S-Video with NTSC signal is selected.

Adjusting Sharpness

Highlight the PICTURE > Sharpness menu and press / .

The higher the value, the sharper the picture becomes. The lower the value, the softer the picture becomes.

This function is only available when a Video, S-Video or Component Video signal is selected.

Adjusting Brilliant Color

Highlight the PICTURE > Brilliant Color menu and press / .

This feature utilizes a new color-processing algorithm and system level enhancements to enable higher brightness while providing truer, more vibrant colors in the projected picture.

It enables a greater than 50% brightness increase in mid-tone images, which are common in video and natural scenes, so the projector reproduces images in realistic and true colors. If you prefer images with that quality, select On. If you don’t need it, select Off.

When Off is selected, the Color Temperature and 3D Color Management functions are not available.

Selecting a Color Temperature

Highlight the PICTURE > Color Temperature menu and press / .

The options available for color temperature* settings vary according to the signal type selected.

1.

Cool: Makes images appear bluish white.

2.

Normal: Maintains normal colorings for white.

3.

Warm: Makes images appear reddish white.

*About color temperatures:

27

There are many different shades that are considered to be "white" for various purposes. One of the common methods of representing white color is known as the “color temperature”. A white color with a low color temperature appears to be reddish white. A white color with a high color temperature appears to have more blue in it.

Color Management

Only in permanent installations with controlled lighting levels such as boardrooms, lecture theaters, or home theaters, should color management be considered. Color management provides fine color control adjustment to allow for more accurate color reproduction, should you require it.

If you have purchased a test disc which contains various color test patterns and can be used to test the color presentation on monitors, TVs, projectors, etc., you can project any image from the disc on the screen and enter the 3D Color Management menu to make adjustments.

To adjust the settings:

1.

Go to the DISPLAY menu and highlight 3D Color Management.

2.

Press MODE/ENTER on the projector or remote control and the 3D Color

Management page is displayed.

3.

Highlight Primary Color and press / to select a color from among Red, Yellow,

Green, Cyan, Blue, or Magenta.

4.

Press to highlight Hue and press / to select its range. Increase in the range will

5.

include colors consisted of more proportions of its two adjacent colors.

Please refer to the illustration to the right for how the colors relate to each other.

For example, if you select Red and set its range at 0, only pure red in the projected picture will be selected. Increasing its range will include red close to yellow and red close to magenta.

RED

Yellow

Press

Magenta

Cyan

GREEN

its values to your preference by pressing /

BLUE

. Every adjustment made will reflect to the image immediately.

For example, if you select Red and set its value at 0, only the saturation of pure red will be affected.

Saturation is the amount of that color in a video picture. Lower settings produce less saturated colors; a setting of “0” removes that color from the image entirely. If the saturation is too high, that color will be overpowering and unrealistic.

6.

Press to highlight Gain and adjust its values to your preference by pressing / .

The contrast level of the primary color you select will be affected. Every adjustment made will reflect to the image immediately.

7.

Repeat steps 3 to 6 for other color adjustments.

8.

Make sure you have made all of the desired adjustments.

9.

Press MENU on the projector or MENU/EXIT on the remote control to exit and save the settings.

28

Setting the presentation timer

This function is only available when an input signal is selected and active.

Presentation timer can indicate the presentation time on the screen to help you achieve better time management when giving presentations. Follow these steps to utilize this function:

1.

Press TIMER SET UP on the remote control to access the Presentation Timer menu or go to the SYSTEM SETTING: Basic > Presentation Timer menu and press

MODE/ENTER to display the Presentation Timer page.

2.

Highlight Timer Period and decide the time period by pressing / . The length of time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5minute increments.

If the timer is already on, the timer will restart whenever the Timer Period is reset.

3.

Press the screen by pressing /

.

Selection

Always

Description

Displays the timer on screen throughout the presentation time.

1 min/2 min/3 min Displays the timer on screen in the last 1/2/3 minute(s).

Never Hides the timer throughout the presentation time.

4.

Press highlight

.

Top-Left Bottom-Left Top-Right Bottom-Right

5.

Press direction by pressing / .

Selection

Count Up

Count Down

Description

Increases from 0 to the preset time.

Decreases from the preset time to 0.

6.

Press reminder by pressing / . If you select On, a double beep sound will be heard at the last 30 seconds of counting down/up, and a triple beep sound will be produced when the timer is up.

7.

To activate the presentation timer, press and press / to highlight On and press

MODE/ENTER.

8.

A confirmation message displays. Highlight Yes and press MODE/ENTER on the projector or remote control to confirm. You will see the message “Timer is On” displaying on the screen. The timer starts counting when the timer is on.

29

To cancel the timer, perform the following steps:

1.

Go to the SYSTEM SETTING: Basic > Presentation Timer menu and highlight

Off. Press MODE/ENTER. A confirmation message displays.

2.

Highlight Yes and press MODE/ENTER to confirm. You will see the message

“Timer is Off” displaying on the screen.

Hiding the image

In order to draw the audience's full attention to the presenter, you can use on the projector or BLANK on the remote control to hide the screen image. Press any key on the projector or remote control to restore the image.

You can set the blank time in the taken on the blank screen.

SYSTEM SETTING: Basic > Blank Timer

menu to let the projector return the image automatically after a period of time when there is no action

CAUTION

Do not block the projection lens from projecting as this could cause the blocking object to become heated and deformed or even cause a fire.

Locking control keys

With the control keys on the projector locked, you can prevent your projector settings from being changed accidentally (by children, for example). When the Panel Key Lock is on, no control keys on the projector will operate except .

1.

Press on the projector or Lock on the remote control, or go to the

SYSTEM

SETTING: Basic > Panel Key Lock menu

, and select On by pressing / on the projector or remote control.

2.

A confirmation message is displayed. Select Yes to confirm.

To release panel key lock, press and hold on the projector or Lock on the remote control for 3 seconds.

You can also use the remote control to enter the SYSTEM SETTING: Basic > Panel Key

Lock menu and press / to select Off.

• Keys on the remote control are still functional when panel key lock is enabled.

• If you press to turn off the projector without disabling panel key lock, the projector will still be in locked status the next time it is turned on.

Freezing the image

Press FREEZE on the remote control to freeze the image. The word 'FREEZE' will be displayed in the upper left corner of the screen.

To release the function, press any key on the projector or remote control.

Even if an image is frozen on the screen, the pictures are running on the video or other device. If the connected devices have active audio output, you will still hear the audio even though the image is frozen on screen.

30

Operating in a high altitude environment

We recommend you use the High Altitude Mode when your environment is between 1500 m–3050 m above sea level, and temperature is between 0°C–30°C.

CAUTION

Do not use the High Altitude Mode if your altitude is between 0 m and 1499 m and temperature is between 0°C and 35°C. The projector will be over cooled, if you turn the mode on under such a condition.

To activate the High Altitude Mode:

1.

Press MENU on the projector or MENU/EXIT on the remote control and then press / until the SYSTEM SETTING: Advanced menu is highlighted.

2.

Press

High Altitude Mode

Select 1 or 2

1. (High) Equal or higher than 1500m

2. (Normal) Lower than 1500m

1 2

press / to select 1 or 2.

3.

A confirmation message is displayed.

4.

Highlight 1 and press MODE/ENTER on the projector or remote control.

Operation under "High Altitude Mode" may cause a higher decibel operating noise level because of increased fan speed necessary to improve overall system cooling and performance.

If you use this projector under other extreme conditions excluding the above, it may display auto shut-down symptoms, which is designed to protect your projector from over-heating.

In cases like this, you should switch to High Altitude Mode to solve these symptoms.

However, this is not to state that this projector can operate under any and all harsh or extreme conditions.

Shutting down the projector

1.

Press and a confirmation message is displayed prompting you.

If you don't respond in a few seconds, the message will disappear.

2.

Press a second time.

3.

Disconnect the power cord from the wall socket if the projector will not be used in an extended period of time.

CAUTION

• To protect the lamp, the projector will not respond to any commands during the cooling process.

• Do not unplug the power cord before the projector shutdown sequence is complete.

AUDIO IN

S

AUDIO OUT

31

Menu operation

Menu system

Please note that the on-screen display (OSD) menus vary according to the signal type selected.

The menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

Main menu

1.

DISPLAY

2.

PICTURE

Sub-menu Options

Wall Color

Off/Light Yellow/Pink/Light

Green/Blue/Blackboard

Auto/Real/4:3/16:9 Aspect Ratio

Keystone

Position

Phase

H. Size

Magnify

3D Sync

3D Sync Invert

Preset Mode

Brightness

Contrast

Color

Tint

Sharpness

Brilliant Color

Color Temperature

3D Color

Management

Primary Color

Hue

Saturation

Gain

Auto/Frame Sequential/Frame

Packing/Top-Bottom/Side-by-

Side/Off

Disable/Invert

Bright/Presentation/sRGB/Cinema/Game/User

On/Off

Cool/Normal/Warm

R/G/B/C/M/Y

32

Main menu

3. SOURCE

Sub-menu

Quick Auto Search

Auto Adjustment

Timer Period

Timer Display

4.

SYSTEM

SETTING:

Basic

Presentation

Timer

Language

Mirror

Auto Power Off

Timer Position

Timer Counting

Direction

Sound Reminder

On/Off

Blank Timer

Panel Key Lock

Sleep Timer

Background Color

Off/On

Options

1~240 minutes

Always/1 min/2 min/3 min/

Never

Top-Left/Bottom-Left/Top-

Right/Bottom-Right

Count Down/Count Up

On/Off

Multi-language OSD selection

Normal/H Invert/V Invert/H & V

Invert

Disable/5 min/10 min/15 min/

20 min/25 min/30 min

Disable/5 min/10 min/15 min/

20 min/25 min/30 min

On/Off

Disable/30 min/1 hr/2 hr/3 hr/4 hr/8 hr/12 hr

Black/Blue/Original

33

Main menu

Quick Cooling

Sub-menu

High Altitude Mode

Audio Settings

Mute

Volume

Menu Display Time

5.

SYSTEM

SETTING:

Advanced

Menu Settings

Standby Mode

Menu Position

Lamp Settings

Security Settings

Closed Caption

Reset All Settings

6.

INFORMATION

Current System Status

Lamp Mode

Reset Lamp Timer

Equivalent Lamp

Hour

Change Password

Power on Lock

Closed Caption

Enable

Caption Version

Reset/Cancel

Options

On/Off

1 (High) Equal or higher than 1500 m

2 (Normal) Lower than

1500 m

On/Off

5 sec/10 sec/15 sec/20 sec/25 sec/30 sec

Center/Top-Left/Top-

Right/Bottom-Right/

Bottom-Left

Normal/Saving

Normal/Economic/

Intelligent Eco

On/Off

On/Off

CC1/CC2/CC3/CC4

•

Source

•

Preset Mode

•

Color System

•

Resolution

•

Equivalent Lamp Hour

•

Serial Number

34

Description of each menu

Function Description

In the situation where you are projecting onto a colored surface such as a painted wall which may not be white, the Wall Color feature can help correct the projected picture' colors to prevent possible color difference between the source and projected pictures.

Wall Color

Aspect Ratio

Keystone

Position

Use the / buttons to select a color which is closest to the color of the projection surface.

This function is only available when a computer signal (analog

RGB) is selected.

There are three options to set the image's aspect ratio depending on

your input signal source. See "Selecting the aspect ratio" on page 24

for details.

Corrects any keystoning of the image. See

"Correcting keystone" on page 23 for details.

Displays the position adjustment page. To move the projected image, use the directional arrow keys. The values shown on the lower position of the page change with every key press you made until they reach their maximum or minimum.

This function is only available when a computer signal (analog

RGB) is selected.

Adjusts the clock phase to reduce image distortion.

Phase

H. Size

Magnify

This function is only available when a computer signal (analog RGB) is selected.

Adjusts the horizontal width of the image.

This function is only available when a computer signal (analog

RGB) is selected.

Magnifies or reduces the projected image. See "Magnifying and searching for details" on page 23 for details.

35

Function

3D Sync

Description

This projector features 3D function which enables you to enjoy 3D movies, videos, and sporting events in a more realistic way by presenting the depth of the images. You need to wear a pair of 3D glasses to view 3D images.

1.

Press the MODE/ENTER button to display the 3D Sync menu.

2.

Use the / buttons to select a 3D sync mode.

- When Auto is selected, the projector detects the input signal and determines a suitable 3D sync mode automatically. In case the 3D sync mode is not detected correctly and the 3D image is not displayed properly, select another 3D sync mode until the image is displayed correctly.

- If Off is selected, the 3D function will be turned off.

The 3D function is only available when the refresh rate of the

Video source is 60Hz and computer source is 120Hz.

3D Sync Invert

When the 3D Sync function is on:

• The brightness level of the projected image will decrease.

• The Preset Mode cannot be adjusted.

• Images cannot be magnified.

When you discover the inversion of the image depth, enable this function to correct the problem.

36

Function

Preset Mode

Brightness

Contrast

Color

Tint

Sharpness

Brilliant Color

Color

Temperature

3D Color

Management

Quick Auto

Search

Description

Pre-defined preset modes are provided so you can optimize your projector image set-up to suit your program type. See

"Selecting a preset mode" on page 26

for details.

Adjusts the brightness of the image. See "Adjusting Brightness" on page 26

for details.

Adjusts the degree of difference between dark and light in the image.

See

"Adjusting Contrast" on page 27 for details.

Adjusts the color saturation level -- the amount of each color in a video image. See

"Adjusting Color" on page 27 for details.

This function is only available when a Video, S-Video or

Component Video signal is selected.

Adjusts the red and green color tones of the image. See

"Adjusting

Tint" on page 27

for details.

The function is only available when a Video or S-Video signal with NTSC system is selected.

Adjusts the image to make it look sharper or softer. See "Adjusting

Sharpness" on page 27

for details.

This function is only available when a Video, S-Video or

Component Video signal is selected.

Adjusts white peaking while maintaining correct color presentation.

See

"Adjusting Brilliant Color" on page 27

for details.

See

"Selecting a Color Temperature" on page 27

for details.

See

"Color Management" on page 28 for details.

See

"Switching input signal" on page 21

for details.

Auto

Adjustment

See

"Auto-adjusting the image" on page 22 for details.

37

Function

Presentation

Timer

Language

Mirror

Auto Power

Off

Blank Timer

Panel Key

Lock

Description

Reminds the presenter to finish the presentation within a certain time

frame. See "Setting the presentation timer" on page 29

for details.

Sets the language for the On-Screen Display (OSD) menus. See

"Using the menus" on page 18 for details.

See "Choosing a location" on page 10 for details.

Allows the projector to turn off automatically if no input signal is

detected after a set period of time. See "Setting Auto Power Off" on page 42 for details.

Sets the image blank time when the Blank feature is activated, once

elapsed the image will return to the screen. See "Hiding the image" on page 30 for details.

Disables or enables all panel key functions except POWER on the projector and keys on the remote control. See

"Locking control keys" on page 30 for details.

This function allows the projector to turn off automatically if there is no user operation after a set period of time.

Sleep Timer

Use the / to select the period of time.

Background

Color

Allows you to select which logo screen will be displayed during projector start-up.

Quick Cooling

Enables or disables the Quick Cooling function. Use the / buttons to select On or Off.

Selecting On enables the function and projector cooling time will be shortened from a normal 70-second duration to approximately 13 seconds.

A mode for operation in high altitude areas. See "Operating in a high altitude environment" on page 31 for details.

High Altitude

Mode

Audio Settings

Menu Settings

The sound adjustments made as below will have an effect on the projector speaker. Be sure you have made a correct connection to the

projector audio input/output ports. See "Connection" on page 12 for

more details.

Mute

Mutes the sound received from AUDIO IN and HDMI.

Volume

Adjusts the sound level received from AUDIO IN and HDMI.

Menu Display Time

Sets the length of time the OSD will remain active after your last key press. The range is from 5 to 30 seconds in 5-second increments.

Menu Position

Sets the On-Screen Display (OSD) menu position.

38

Function Description

Standby Mode

Lamp Settings

Use / to select a standby mode.

Normal

The projector is able to provide the following functions when it is in standby mode.

• The projector can output a VGA signal when it is in standby mode and the COMPUTER IN 1 port is correctly connected to devices.

• The projector can output audio signals when it is in standby mode and the corresponding ports are correctly connected to devices.

Speaker is disabled in standby mode.

See "Connection" on page 12 for how to make the connections.

Saving

The projector consumes less than 0.5W power during standby when this mode is selected. The Monitor out and Audio out functions are disabled.

Lamp Mode

See "Setting Lamp Mode as Economic or Intelligent Eco" on page 42

for details.

Reset Lamp Timer

See "Resetting the lamp timer" on page 45 for details.

Equivalent Lamp Hour

See "Getting to know the lamp hour" on page 42 for details on how

the total lamp hour is calculated.

Security

Settings

See "Utilizing the password function" on page 19 for details.

Closed

Caption

Reset All

Settings

Closed Caption Enable

Activates the function by selecting On when the selected input signal carries closed captions.

• Captions: An on-screen display of the dialogue, narration, and sound effects of TV programs and videos that are closed captioned (usually marked as "CC" in TV listings).

This function is only available when a Composite video or S-

Video input signal is selected and its system format is NTSC.

Caption Version

Selects a preferred closed captioning mode. To view captions, select

CC1, CC2, CC3, or CC4 (CC1 displays captions in the primary language in your area).

Returns all settings to the factory preset values.

The following settings will still remain: Language, Mirror, High

Altitude Mode, Security Settings.

39

Function

Current

System Status

Description

Source

Shows the current signal source.

Preset Mode

Shows the selected mode in the PICTURE menu.

Color System

Shows input system format, NTSC, PAL, SECAM, or RGB.

Resolution

Shows the native resolution of the input signal.

Equivalent Lamp Hour

Displays the number of hours the lamp has been used.

Serial Number

Shows the serial number of the projector.

40

Maintenance

Care of the projector

Your projector needs little maintenance. The only thing you need to do on a regular basis is to keep the lens clean.

Never remove any parts of the projector except the lamp. Contact your dealer if other parts need replacing.

Cleaning the lens

Clean the lens whenever you notice dirt or dust on the surface.

• Use a canister of compressed air to remove dust.

• If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner and gently wipe the lens surface.

CAUTION

Never rub the lens with abrasive materials.

Cleaning the projector case

Before you clean the case, turn the projector off using the proper shutdown procedure as described in

"Shutting down the projector" on page 31

and unplug the power cord.

• To remove dirt or dust, wipe the case with a soft, lint-free cloth.

• To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH detergent. Then wipe the case.

CAUTION

Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the case.

Storing the projector

If you need to store the projector for an extended time, please follow the instructions below:

• Make sure the temperature and humidity of the storage area are within the recommended range for the projector. Please refer to

"Specifications" on page 48

or consult your dealer about the range.

• Retract the adjuster feet.

• Remove the battery from the remote control.

• Pack the projector in its original packing or equivalent.

Transporting the projector

It is recommended that you ship the projector with its original packing or equivalent.

41

Lamp information

Getting to know the lamp hour

When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer. The method of calculating the equivalent lamp hour is as follows:

Total lamp hour = (hours used in Normal mode) + (hours used in Economic mode) +

(hours used in Intelligent Eco mode)

To obtain the lamp hour information:

1.

Press MENU on the projector or MENU/EXIT on the remote control and then press

/ until the SYSTEM SETTING: ADVANCED menu is highlighted.

2.

Press remote control. The Lamp Settings page is displayed.

3.

You will see the Equivalent lamp hour information on the menu.

4.

To leave the menu, press MENU on the projector or MENU/EXIT on the remote control.

You can also get the lamp hour information on the INFORMATION menu.

Extending lamp life

The projection lamp is a consumable item. To keep the lamp life as long as possible, you can do the following settings via the OSD menu.

Setting Lamp Mode as Economic or Intelligent Eco

Using Economic/Intelligent Eco mode reduces system noise and power consumption. If the Economic/Intelligent Eco mode is selected, the light output will be reduced and result in darker projected pictures.

Setting the projector in Economic/Intelligent Eco mode also extends the lamp operation life. To set Intelligent Eco mode, go into the SYSTEM SETTING: ADVANCED > Lamp

Settings > Lamp Mode menu and press / .

Setting Auto Power Off

This function allows the projector to turn off automatically if no input source is detected after a set period of time to prevent unnecessary waste of lamp life.

To set Auto Power Off, go into the SYSTEM SETTING: BASIC > Auto Power Off menu and press / . If the preset time lengths are not suitable for your presentation, select

Disable. The projector will not automatically shut down in a certain time period.

42

Replacing the lamp

To prepare a new lamp, contact your dealer and tell the lamp type number.

Type number: DT01853

WARNING

• The projector uses a high-pressure mercury glass lamp.

• The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.

Hg - Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org

• To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the lamp.

• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp.

• To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp glass that has shattered into sharp pieces. Before replacing the lamp, clean the lamp compartment and dispose of cleaning materials. Be careful of sharp edges in the lamp compartment. Wash hands after lamp replacement.

• If the lamp should break (it will make a loud bang when it does), ventilate the room well, and make sure not to inhale the gas or fine particles that come out from the projector's vent holes, and not to get them into your eyes or mouth.

• Only certified lamps are tested with this projector. Use of other lamps may cause electrical shock and fire.

• Be sure to place the projector on a flat surface to replace the lamp.

1.

Turn the power off and disconnect the power cord from the wall socket. If the lamp is hot, avoid burns by waiting for approximately 45 minutes until the lamp has cooled.

2.

Prepare a new lamp. If the projector is mounted in a high position, or if the lamp has broken, also ask the dealer to replace the lamp.

3.

Loosen the screw of the lamp cover. Refer to the right figure to identify the screw.

4.

Remove the lamp cover from the projector.

WARNING

• Do not turn the power on with the lamp cover removed.

• Do not insert your fingers between the lamp and the projector. It may cause injuries.

1

2

43

5.

Remove the protection film. Loosen the screw that secures the lamp. Refer to the right figure to identify the screw.

1

2

6.

Disconnect the lamp's wire connector from the projector, and then slowly pick up the lamp by the handle.

CAUTION

• Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.

• Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials.

• Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images.

7.

Insert the new lamp into the lamp compartment and make sure it fits in the projector. Connect the new lamp’s wire connector to the projector.

2

8.

Tighten the screw that secures the lamp.

CAUTION

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screw.

9.

Ensure the handle is fully laid flat and locked in place.

10. Replace the new protection film that comes with the new lamp.

3 2

1

1

44

11.

Replace the lamp cover on the projector.

2

1

12. Tighten the screw that secures the lamp cover.

CAUTION

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screws.

13. Restart the projector.

CAUTION

Do not turn the power on with the lamp cover removed.

Resetting the lamp timer

14. After the startup logo, open the On-Screen

Display (OSD) menu.

15. Go to the SYSTEM SETTING:

ADVANCED > Lamp Settings menu. Press

MODE/ENTER on the projector or remote control. The Lamp Settings page is displayed.

16. Press Reset lamp timer and press MODE/ENTER on the projector or remote control. A warning message is displayed asking if you want to reset the lamp timer.

17. Highlight Reset and press MODE/ENTER on the projector or remote control. The lamp time will be reset to '0'.

CAUTION

Do not reset if the lamp is not new or replaced as this could cause damage.

Notice

Reset Lamp Timer?

Reset Cancel

45

Indicators

Light

POWER TEMP LAMP

Off

Status & Description

Off

System Messages

Stand-by

Purple

Blue

Flashing

Blue

Purple

Flashing

Off

Off

Off

Off

Off

Off

Powering up

Normal operation

Power-down cooling

Blue

Red

Flashing

Off

Off

Red

Red

Red

Blue

Off

Off

Off

Off

Off

Red

Red

Flashing

Red

Red

Off

CW start fail. Please contact your dealer for assistance.

Scaler shutdown fail. Please contact your dealer for assistance.

Lamp Error Messages

Red

Red

Flashing

Red

Flashing

Lamp error. Please contact your dealer for assistance.

Lamp is not lit up. Please contact your dealer for assistance.

Lamp door is open.

Thermal Error Messages

Off

Fan 1 error. Please contact your dealer for assistance.

Off

Off

Fan 2 error. Please contact your dealer for assistance.

Over heated. Please contact your dealer for assistance.

46

Troubleshooting

The projector does not turn on.

Cause

There is no power from the power cord.

Remedy

Plug the power cord into the AC inlet on the projector, and plug the power cord into the power outlet. If the power outlet has a switch, make sure that it is switched on.

Wait until the cooling down process has completed.

Attempting to turn the projector on again during the cooling process.

No picture

Cause

The video source is not turned on or connected correctly.

The projector is not correctly connected to the input signal device.

The input signal has not been correctly selected.

Remedy

Turn the video source on and check that the signal cable is connected correctly.

Check the connection.

Select the correct input signal with the

SOURCE key on the projector or remote control.

Blurred image

Cause

The projection lens is not correctly focused.

The projector and the screen are not aligned properly.

Remote control does not work

Cause

The battery is out of power.

There is an obstacle between the remote control and the projector.

You are too far away from the projector.

Remedy

Adjust the focus of the lens using the focus ring.

Adjust the projection angle and direction as well as the height of the projector if necessary.

Remedy

Replace the battery with a new one.

Remove the obstacle.

Stand within 4 meters (~13 feet) of the projector.

47

Specifications

Projector specifications

• All specifications are subject to change without notice.

• Not all models can be purchased in your region.

General

Product name

Optical

Resolution

Display system

Lamp

Electrical

Projector

1024 x 768 XGA

1-CHIP DMD

220 W lamp

Power supply

Power consumption

Mechanical

AC 100-120V: 3.2 A, AC 220-240V: 1.5 A

AC 100-120V: 310W, AC 220-240V: 300W

Weight

Input terminal

Approx. 2.4 kg

Computer input

COMPUTER IN1 port

COMPUTER IN2 port D-Sub 15-pin (female) x 2

Video signal input

S-VIDEO port

VIDEO port

SD/HDTV signal input

Mini DIN 4-pin x 1

RCA x 1

Analog – D-Sub <–> Component RCA x 3

(through COMPUTER IN1/COMPUTER IN2 input port)

Audio signal input

Digital – HDMI x 1

AUDIO IN port Stereo mini x 1

48

Output terminal

MONITOR OUT port D-Sub 15-pin (female) x 1

AUDIO OUT port Stereo mini x 1

Speaker 2 watt x 1

Control terminal

CONTROL port

IR receiver

Service terminal

SERVICE port

RS-232 serial control 9 pin x 1

x 1 (Front)

USB mini B x 1

Environmental Requirements

Operating temperature

Operating relative humidity

Operating altitude

• 0°C–35°C at 0–1499 m above sea level

• 0°C–30°C at 1500–3050 m above sea level

10%–90% (without condensation)

• 0–1499 m (with High Altitude Mode 2 (Normal))

• 1500–3050 m (with High Altitude Mode 1 (High))

Dimensions

Max. size 314.6 mm (W) x 91.2 mm (H) x 218.8 mm (D)

Min. size 314.6 mm (W) x 89.1 mm (H) x 208 mm (D)

314.6

Unit: mm

49

Timing chart

Supported timing for PC input

Resolution Mode

Refresh rate

(Hz)

640 x 480

800 x 600

1024 x 768

1152 x 864

1280x720

1280 x 768

1280 x 800

1280 x 1024

1280 x 960

1360 x 768

1440 x 900

1400X1050

1600x1200

1680 x 1050

640 x 480@67Hz

832 x 624@75Hz

1024 x 768@75Hz

1152 x 870@75Hz

VGA_60***

VGA_72

VGA_75

VGA_85

SVGA_60***

SVGA_72

SVGA_75

SVGA_85

SVGA_120*

(Reduce

Blanking)

XGA_60***

XGA_70

XGA_75

XGA_85

XGA_120*

(Reduce

Blanking)

1152 x 864_75

1280 x 720_60***

1280 x 768_60***

WXGA_60***

WXGA_75

WXGA_85

WXGA_120*

(Reduce

Blanking)

SXGA_60**

SXGA_75

SXGA_85

1280 x 960_60**

1280 x 960_85

1360 x 768_60**

WXGA+_60**

SXGA+_60**

UXGA**

1680 x

1050_60**

MAC13

MAC16

MAC19

MAC21

119.854

119.989

75.00

60

59.870

59.810

74.934

84.880

119.909

75.025

85.024

60.000

85.002

60.015

59.887

59.978

60.000

59.954

66.667

74.546

74.93

75.06

• *Supported timing for 3D signal in Frame Sequential format.

H-frequency

(kHz)

77.425

97.551

67.500

45.000

47.776

49.702

62.795

71.554

101.563

79.976

91.146

60.000

85.938

47.712

55.935

65.317

121.750

75.000 162.000

65.290

35.000

49.722

60.241

68.68

Clock

(MHz)

83.000

115.500

108.000

74.250

79.5

83.500

106.500

122.500

146.25

135.000

157.500

108

148.500

85.500

106.500

146.250

30.240

57.280

80.000

100.00

50

• **Supported timing for 3D signal in Top-Bottom and Side-by-Side formats.

• ***Supported timing for 3D signal in Frame Sequential, Top-Bottom and Side-by-Side formats.

Supported timing for HDMI input

Resolution

640 x 480

800 x 600

1024 x 768

1152 x 864

1280 x 720

1280 x 768

1280 x 800

1280 x 1024

1280 x 960

1360 x 768

1440 x 900

1400 x 1050

1600 x 1200

1680 x 1050

640x480@67Hz

832x624@75Hz

1024x768@75Hz

1152x870@75Hz

Mode

VGA_60***

VGA_72

VGA_75

VGA_85

SVGA_60***

SVGA_72

SVGA_75

SVGA_85

SVGA_120*

(Reduce

Blanking)

XGA_60***

XGA_70

XGA_75

XGA_85

XGA_120*

(Reduce

Blanking)

1152 x 864_75

1280x720_60***

1280 x 768_60***

WXGA_60***

WXGA_75

WXGA_85

WXGA_120*

(Reduce

Blanking)

SXGA_60**

SXGA_75

SXGA_85

1280 x 960_60**

1280 x 960_85

1360 x 768_60**

WXGA+_60**

SXGA+_60**

UXGA**

1680x1050_60**

MAC13

MAC16

MAC19

MAC21

Refresh rate

(Hz)

119.854

60.004 48.363 65.000

70.069 56.476 75.000

75.029 60.023 78.750

84.997 68.667 94.500

119.989

75.00

60

59.870

59.810

74.934

84.880

119.909

75.025

85.024

60.000

85.002

60.015

59.887

59.978

60.000

59.954

66.667

74.546

75.020

75.06

H-frequency

(kHz)

77.425

97.551

67.500

45.000

47.776

49.702

62.795

71.554

101.563

• *Supported timing for 3D signal in Frame Sequential format.

79.976

91.146

60.000

85.938

47.712

55.935

65.317

75.000

65.290

35.000

49.722

60.241

68.68

Clock (MHz)

59.940 31.469 25.175

72.809 37.861 31.500

75.000 37.500 31.500

85.008 43.269 36.000

60.317 37.879 40.000

72.188 48.077 50.000

75.000 46.875 49.500

85.061 53.674 56.250

83.000

115.500

108.000

74.250

79.5

83.500

106.500

122.500

146.25

135.000

157.500

108

148.500

85.500

106.500

121.750

162.000

146.250

30.240

57.280

80.000

100.00

51

• **Supported timing for 3D signal in Top-Bottom and Side-by-Side formats.

• ***Supported timing for 3D signal in Frame Sequential, Top-Bottom and Side-by-Side formats.

Timing

480i*

480p

576i

576p

720/50p**

720/60p**

1080/24P**

1080/30P

1080/50i***

1080/60i***

1080/50P

1080/60P

Resolution

720 (1440) x 480

720 x 480

720 (1440) x 576

720 x 576

1280 x 720

1280 x 720

1920 x 1080

1920 x 1080

1920 x 1080

1920 x 1080

1920 x 1080

1920 x 1080

Horizontal frequency

(KHz)

15.73

31.47

15.63

31.25

37.5

45.00

27

33.75

28.13

33.75

56.25

67.5

Vertical frequency

(Hz)

59.94

59.94

50

50

50

60

24

30

50

60

50

60

Dot Clock

Frequency

(MHz)

27

27

27

27

74.25

74.25

74.25

74.25

74.25

74.25

148.5

148.5

• *Supported timing for 3D signal in Frame Sequential format.

• **Supported timing for 3D signal in Frame Packing and Top-Bottom formats.

• ***Supported timing for 3D signal in Side-by-Side format.

Supported timing for Component-YP b

P r input

Timing

480i

480p

576i

576p

720/50p

720/60p

1080/50i

1080/60i

1080/24P

1080/30P

1080/50P

1080/60P

Resolution

720 x 480

720 x 480

720 x 576

720 x 576

1280 x 720

1280 x 720

1920 x 1080

1920 x 1080

1920 x 1080

1920 x 1080

1920 x 1080

1920 x 1080

Horizontal frequency

(KHz)

15.73

31.47

15.63

31.25

37.5

45.00

28.13

33.75

27

33.75

56.25

67.5

Vertical

Frequency

(Hz)

59.94

59.94

50

50

50

60

50

60

24

30

50

60

Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image vibration.

Dot Clock

Frequency

(MHz)

13.5

27

13.5

27

74.25

74.25

74.25

74.25

74.25

74.25

148.5

148.5

52

Supported timing for Video and S-Video inputs

Video mode

NTSC

PAL

SECAM

PAL-M

PAL-N

PAL-60

NTSC4.43

Horizontal

Frequency (kHz)

15.73

15.63

15.63

15.73

15.63

15.73

15.73

Vertical Frequency

(Hz)

60

50

50

60

50

60

60

Color sub-carrier

Frequency (MHz)

3.58

4.43

4.25 or 4.41

3.58

3.58

4.43

4.43

53

Regulation Statements

FCC statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

•

•

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Changes or modifications not expressly approved by the manufacturer void the user's authority to operate the equipment.

ICES-003

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.

WEEE

Disposing of this product correctly will help save valuable resources and prevent any potential negative effects on human health and the environment, which could otherwise arise from inappropriate waste handling.

Please contact your local authority for further details of your nearest designated collection point.

Penalties may be applicable for incorrect disposal of this waste, in accordance with you national legislation.

For business users in the European Union

If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

Information on Disposal in other Countries outside the European Union

54

This symbol is only valid in the European Union. If you wish to discard this product please contact your local authorities or dealer and ask for the correct method of disposal.

55

Copyright information

Copyright

Copyright 2015. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of this company.

Disclaimer

This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, this company reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation to notify any person of such revision or changes.

The illustrations in this manual are for illustrative purposes. They may differ slightly from your projector.

The reproduction, transfer or copy of all or any part of this document is not permitted without express written consent.

*DLP and Digital Micromirror Device (DMD) are trademarks of Texas Instruments. Others are copyrights of their respective companies or organizations.

*Registered trademarks of HDMI Licensing LLC in the United States and other countries.

*Mac

®

and Macintosh

®

are registered trademarks of Apple Inc.

*Microsoft

®

and PowerPoint

U.S. and/or other countries.

®

are registered trademarks of Microsoft Corporation in the

All other trademarks are the properties of their respective owners.

56

Warranty and after-service

If an abnormal operation (such as smoke, strange odor or excessive sound) should occur, stop using the projector immediately.

Otherwise if a problem occurs with the projector, first refer to “Troubleshooting”, and run through the suggested checks.

If this does not resolve the problem, please consult your dealer or service company. They will tell you what warranty condition is applied.

57

Hitachi America, Ltd.

Business Solutions Group

2420 Fenton Street, Suite 200

Chula Vista,CA 91914 USA CANADA

Tel: +1 -800-448-2244

► http://www.hitachi-america.us/projectors

Hitachi Europe Ltd., Digital Media Group

Consumer Affairs Department

Whitebrook Park, Lower Cookham Road,

Maidenhead

Berkshire SL6 8YA UNITED KINGDOM

Tel: 0844 481 0297

(international call is NOT available for this number)

Email: [email protected]

► http://www.equinox.co.uk/hitachi/

Hitachi Europe S.A.S.,

Digital Media Group

31 bis rue du 35ème Régiment de l’aviation

ZAC DU CHENE, 69500 BRON FRANCE

Tel: 0 478 262135 +33 478 262135

Email: [email protected]

Hitachi Europe GmbH

Am Seestern 18

40547 Düsseldorf GERMANY

Tel: 0 40 73353 468 +49 (0) 40 73353 468

Email: [email protected]

Hitachi Europe S.A.

364, Kifissias Ave. & 1, Delfon Str.

152 33 Chalandri

Athens GREECE

Tel: +30 210 921 0800

Email: [email protected]

Hitachi Europe S.r.l.

Via T. Gulli, 39

20147 MILANO ITALY

Tel: +39 2 257 12355

Email: [email protected]

Hitachi Europe S.A.

Gran Via Carles III, 86 Planta 5ª

Edificios Trade - Torre Este

08028 Barcelona SPAIN

Tel: 0 93 266 4747 +34 93 266 4747

Email: [email protected]

Hitachi Europe AB

Frösundaviks Alle 15

169 29 Solna SWEDEN

Sweden Tel: +46 36 16 16 90

Finland Tel: +358 9 8494 133

Norway Tel: +47 2290 1930

Denmark Tel: +45 7562 4577

► http://www.hitachidigitalmedia.com

Hitachi Australia Pty Ltd.

Suite 801, Level 8, 123 Epping Road

North Ryde N.S.W 2113 AUSTRALIA

Tel: +61 -2-9888-4100

► http://www.hitachi.com.au

Hitachi (Hong Kong), Ltd.

18/F., Ever Gain Centre, 28 On Muk Street.,

Shatin, N.T. HONG KONG

Tel: +852 -2113-8883

► http://www.hitachi-hk.com.hk

Hitachi Sales (Malaysia) Sdn. Bhd.

Lot 12, Jalan Kamajuan, Bangi Industrial Estate,

43650 Bandar Baru Bangi, Selangor Darul Ehsan

MALAYSIA

Tel: +60 -3-8911-2670

► http://www.hitachiconsumer.com.my

Hitachi Home Electronics Asia (S) Pte. Ltd.

438A Alexandra Road #01-01/02/03

Alexandra Technopark, 119967 SINGAPORE

Tel: +65 -6536-2520

► http://www.hitachiconsumer.com.sg

Hitachi Sales Corp. of Taiwan

2 nd Floor, No.65, Nanking East Road, Section 3,

Taipei 104 TAIWAN

Tel: +886-2-2516-0500

► http://www.hsct.com.tw

Hitachi Sales (Thailand), Ltd.

994, 996 Soi Thonglor, Sukhumvit 55 Rd.,

Klongtonnua, Vadhana, Bangkok 10110

THAILAND

Tel: +66 -2381-8381-98

► http://www.hitachi-th.com

Hitachi Maxell, Ltd.

JAPAN

► http://www.hitachi.co.jp/proj/

( :Country/Region)

58