Exaco RIGA 5 Kit Assembly Instructions


Add to my manuals
25 Pages

advertisement

Exaco RIGA 5 Kit Assembly Instructions | Manualzz
ALUMINIUM
GREENHOUSE
Riga S/Riga
Subject to technical changes!
Current as of 02/2012
Basic kit
assembly instructions
model Riga
system width 2,96 m
model Riga S
system width 2,32 m
1
Dear garden friend,
congratulations on the purchase of an aluminium greenhouse made by
The construction is simple. First read the assembly instructions and follow them step by step.
Parts and parts list
Please complete all boxes stored dry and protected from direct sunlight!
number of cartons
basic construction
(gable/eaves)
curved center
profiles
windows/
doors
glazing
Riga S/II/III/IV
1
1
1
1
Riga III/IV/V
1
1
1
1
Start with the basic kit. Please do not open all the boxes at the same time. Let's not get confused
by the variety of items.
Before you begin assembly, check on the parts lists, if all parts are present. Each box goes
through a quality check before it is closed, thus missing parts are almost excluded. Should any
parts are missing, please give us the wrong position.
Customer Service: 877-760-8500 or 512-407-8500 [email protected]
Exaco Trading
10203 Metropolitan Dr.
Austin, TX 78758
Location
Choose, if possible, a sunny place for your greenhouse. Avoid the shadow of buildings and trees.
For vegeteables, like tomatoes, cucumbers and melons, make your greenhouse as possible in
north-south-direction. For flowers and potted plants in east-west-direction.
Warning:
The greenhouse should preferably be placed in a sheltered spot and not in
stormy weather. It is dangerous to leave a partly assembled house!
With the correct assembly resists this greenhouse and strong winds. The manufacturer assumes
no responsibility for any damage by improper installation or acts of God.
The constructions of the greenhouse must be conducted by at least two people.
Work with secure, craft-oriented tools. Be careful when assembling on a secure stand of the ladder
(risk of accident!).
In principle, only with gloves on (risk of injury, average risk!).
2
For the configuration you need the following tools:
1 pc. Phillips screwdriver size 2
1 pc. foot-end wrench10 mm
1 pc. screwdriver
1 pc. allen key 3 mm (in the accessoires bag of the roof window)
1 pc. level
1 pc. stepladder
1 pc. file to remove any burrs on the profiles
1 pc. rubber hammer
1 pc. tape measure
You should be careful:
Hexagonal screws can also be inserted later in the plastic slider!
Wedge seals (V23) pull
apart the center!
Plastic slider in the bottom door
frame, side and roof bars
Push the seal 3 - 5 mm between the soil profile and the glazing.
Both within the greenhouse!
Important: This compress the seals because they contract in cold weather!
numbers of wedge seals
length
model
3 - 5 mm
3 - 5 mm
6 - 8 mm
712 mm
768 mm
1030 mm
4
4
4
1
1
1
7
11
14
Riga S II
Riga S III
Riga S IV
length
model
Riga III
Riga IV
Riga V
-5
s.1
po
-4
1
.4-
-2
s.3
o
p
3
.3-
s
s.
s.1
pos.2-3.1
po
po
s.1
-1
pos.2-3.1
pos.1-7
6
-9
8
-5-
s.1
.1-
s.1
po
po
s
po
pos.1-6
po
po
-4
1-5
2
.4-
s
po
-1
s.2
o
p
-9
3
3 - 5 mm
768 mm
1030 mm 1030 mm
1
1
1
pos.1-5-6
s
po
3 - 5 mm
4
4
4
6 - 8 mm
11
14
16
!!!Note: Important information for glazing!!!
The ISO-Cellular sheets, speak glazing, always install the UV coated side out. The plates have
on the protective film has a hint.
The protective film, first loosen the edges and only after the complete assembly pull it off
immediately. After several days of sunlight can burn the film firmly on the plates and can be
solved only with difficulty.
Do not pull the box right after the film, otherwise you could not tell which side has the UV
protection!
Question: Do I have a greenhouse and the greenhouse glazing and "seal"?
In principle: No.
But we recommend the horizontal transitions of the glazing to the profile (see sketch -->
dashed line ----) sealed with neutral cure, silicone transparent, so that as little water and can
therefore get a little dirt in the glas shots.
Advantage: The greenhouse looks to length of optically better. The tendency to formation of
algae just takes considerably in these areas.
Moisture/water can also occur
within the glass/hollow chambers depending on the wheather, since the plastic plates are
not "water-vapor-permeable
solid", ie moisture occurs in the
form of water vapor into the
plate. This is possible a purely
optical disadvantage, however,
can not be avoided.
The plates can thus take no
damage, even at freezing temperatures.
Warning: Use only neutral cure silicone, otherwise it may lead to stress cracks in plastic deglazing. This is the most common silicone sealant.
It is in any hardware store or at HOKLAR-Therm for about 4 - 6 € available/
cartridge.
Cleaning and care:
The greenhouse with plenty of water such as car washing brush. In addition, using a little
detergent.
4
Foundation frame for digging (optional)
!!!Warning: Use only according to instructions under foundation. See below!!!
This is the easiest, safest and also foundation of a greenhouse.
The foundation frame is hooked force-fit into the soil profile of the greenhouse screwed into the corners with a corner angle (V26). (See page 6).
The foundation frame is assemble to coincide with the greenhouse
together.
Setting up the foundation frame
A small ditch, sod (about 10 - 12 cm deep), dug into the dimensions of the
foundation frame. Use in the corners as a paving stone according to the
other horizontally.
These are then the safe circulation and avoid "bagging" a possibly of the
greenhouse. The greenhouse and the foundation frame in this "gab" and set them
with earth fill.
Expedient is also the creation of garden slaps or stone pavement, so the
greenhouse at eg heavy rain is not covered by mud splashes is.
In addition, the work made easier around the greenhouse, such as mowing the
lawn.
Profiles and accessoires for foundation frame Riga S:
overview
pos.
6.1
6.2
V26
V27
description
foundation frame profile/
gable
foundation frame profile/
eaves
foundation frame corner bracket
40/40/2 x 105
item no 9999 0078
mounting bracket
(rung/foundation frame)
item no 9999 0267
S12
S1
hexagonal screw M6 x 12 +
nut M6
number/length in mm
type II
type III
type IV
2
2
2
2199
2199
2199
2
2
2
2033
3091
4149
4
4
4
105
105
105
10
135
10
135
10
135
20
20
20
item no 9999 0124 + 9999 0128
Profiles and accessoires for foundation frame Riga: (V26/V27/S12/S1 as above)
overview
pos.
6.1
6.2
description
foundation frame profile/
gable
floundation frame profile/
eaves
5
number/length in mm
type III
type IV
type V
2
2
2
2835
2835
2835
2
2
2
3091
4149
5207
Assembly foundation frame
The foundation frame profiles separately in the soil
profiles rotate and center align.
Note: The foundation frame profiles are shorter than
soil profiles!
Note: The foundation frame profiles
are shorter than
soil profiles!
To stabilisize the house,
the mounting bracket
(V27) using bolts M6 x 12
(S12) retracted bolted to
the foundation frame and
the side rungs or door
frames.
In the foundation frame profiles in the corner of
one bolt M6 x 12 (S12) to move, corner brackets
(V26) and fasten with nut M6 (S1).
Foundation of the greenhouse
We recommend that you use for the bolt in place anchor bolts. These are not included!
side rung/
door frame
mounting bracket
- offset - (V15)
bolt M6 x 12 (S12)
+ nut M6 (S1)
soil profile
6
Foundation plan Riga S/Riga
all dimensions in [cm]
Foundation of your greenhouse with a strip foundation
If you have not bought a foundation frame, the secure foundation by means fo strip
foundation. Then please create such a foundation in accordance with the specified
dimensions below.
You have set up your possibility to the greenhouse on low cur stones such as,
50 x 25 x 8 cm or better 50 x 30 x 10 cm.
Please note that the foundation is made evenly horizontally.
exterior edge of the foundation
The greenhouse then please anchoring with the included mounting brackets (V15)
with the dowels (minimum)
7
Screws and ancors are not included.
exterior edge of the greenhouse
frost-free ground
upper edge of ground
model
Riga S II
Riga S III
Riga S IV
Riga III
Riga IV
Riga V
foundation
B1
L1
greenhouse
B2
L2
249
249
249
312
312
312
232
338
443
338
443
533
233
233
233
296
296
296
216
322
427
322
427
533
Content main box - basic kit Riga S/Riga
Please check in the tables list the completeness of the components.
Profiles for both gables:
overview
pos.
1.1
number/length in mm
Riga S
Riga
II
III
IV
III
IV
2
2
2
2
2
2238 2238 2238 2874 2874
description
soil profile/gable
V
2
2874
1.5.4 rand rung left - curved
2
2
2
2
2
2
1.5.6 rand rung right - curved
2
2
2
2
2
2
2
1876
2
1876
2
758
1
758
4
702
2
1876
2
1876
2
758
1
758
4
702
2
1876
2
1876
2
758
1
758
4
702
2
2059
2
2059
2
758
1
758
4
1020
2
2059
2
2059
2
758
1
758
4
1020
2
2059
2
2059
2
758
1
758
4
1020
1.6
1.7
1.8
1.8
1.9
door frame left
with slant
door frame right
with slant and drilling
door frame above
crossbar
in the side door without
crossbar left and right
Profiles for eaves:
overview
pos.
description
II
number/length in mm
Riga S
Riga
III
IV
III
IV
V
2.1
soil profile/eaves
2
2072
2
3130
2
4188
2
3130
2
4188
2
5246
2.3
side rung - curved
2
4
6
4
6
8
3.2
cross bar/roof window
1
1020
1
1020
2
1020
1
1020
2
1020
4
1020
3.3
ridge profile
1
2137
1
3195
1
4253
1
3195
1
4253
1
5311
3.4
angle stabilization
4
2104
4
3162
4
4220
4
3162
4
4220
4
5278
8
Accessories bag basic kit Riga S/Riga
overview
num- number
ber
RigaS Riga
description/
pos.
item number
V9
corner soil profile
4
4
Ortgangprofil/Türzarge
4
4
mounting
crossbar/rear
2
2
2
2
item no 9999 0003
V5
connecting plate
item no 9999 0028
V10
connecting plate 90 x 35 mm
item no 9999 0030
V11
endplate ridge/gutter
item no 9999 0075
V4
connecting plate
for crossbar/roof window
item no 9999 0031
V12
S21
corner
30/30/2/15 mm
item no 9999 0072
blind plug Ø10 mm
II = 2 III = 2
III = 2 IV = 4
IV= 4 V = 8
soil profile
screw the corner from inside
4
4
rand rung -drilling crossbar
4
4
door threshold seal
1
1
sealing the soil profile inside
See
table
below !
See
table
below!
door frame-soil profile/
cover plate/corner (V12)
38*
38*
gable
6
6
item no 9999 0097
V14
hose section 760 mm lg.
item no 9999 0181
V23
wedge seal 3 - 5 mm
item no 9999 0119
S9
self-tapping screw pan head
4,2 x 13
item no 9999 0144
S13
self-tapping screw pan head
4,8 x 45
item no 9999 0150
S5/
S1
hexagnal screw M6 x 16
+ nut
screws for pulling
item no 9999 0183 + 9999 0128
for the attachement of the
greenhouse on foundation by
customer (not with foundation
item no 9999 0207 frame)
V15
mounting bracket - offset
74 x 30 x 33 mm
S32
washer A6,4
door frames, roof and side
rungs
item no 9999 0173
V1
mounting corner bracket
inside
item no 9999 00074
9
II = 40* III = 40*
III = 40* IV = 44*
IV = 44* V = 48*
10
10
20
20
V = 24
je
je
2x lks. 2x lks.
2x rts. 2x rts.
Assembly procedure gable
view from inside
ATTENTION! When using a foundation frame assemble in advance on this soil profile (see page S. 5, 6)
step 1
to step 1:
door frame right (pos.1.7)
door frame left (pos.1.6)
corner soil profile (V9)
First, please slide the door frame
left (pos.1.6) and the door frame
(pos.1.7)
(profile with 8 drill holes, a 30° chamfer and
a black plastic glide)
up to the small holes in the middle
of the soil profile. The chamfer must
show this to the outside. Then attach the corner bracket (V9) on the
soil profile.
soil profile (pos.1.1)
step 2
to step 2:
Riga
730 x 728
1048 x 728
gl
az
i
gl
az
i
ng
ng
Riga S
Even now you need the small side
windows.
Dimensions are listed in the table.
With bar direction - vertical - in the
soil profile and sideways while in the
door frame.
self-tapping screw pan head 4,2 x 13 (S9)
Note: Only after the screw mounting of the door -->
ability to align.
to step 3:
step 3
Now the crossbar (pos. 1.9) is inserted from the top of the glazing.
crossbar (pos.1.9)
crossbar (pos.1.9)
self-tapping screw pan head 4,2 x 13 (S9)
step 4
view from inside
connecting plate (V5)
g
az
in
screw M6 x 16 (S5)
with nut M6 (S1)
gl
gl
az
in
g
door frame
above
(pos.1.8)
10
to step 4:
Before the connecting plate (V5)
with the door frame above (pos.1.8)
screwed, slide in the vertical door
frames (pos.1.6/1.7) two hex screws
M6 x 16 (S5) and in the horizontal
door frame in M6 x 16 (S5) one.
Assembly procedure gable
view from inside
ATTENTION! When using a foundation frame assemble in advance on this soil profile (see page 5, 6)
to step 5:
holes for
door lock
The square peg of the corner connector is plugged in the rand rung
(pos.1.5.4/1.5.6).
Small triangular glazing positioned
on the door frame (pos.1.8).
rand rung right - curved (pos.1.5.6)
rand rung left - curved (pos.1.5.4)
step 5
glazing
The rand rung by means of
connecting plate (V5) screwed to
the door frame. On the rand rung
you need 2 self-tapping screws pan
head 4,2 x 13 (S9), on the door
frame 2 hexagonal screws M6 x 16
(S5).
rand rung to the corner connection peg plugged
- See also step 4! -
step 6:
to step 6:
view from outside
The crossbars (pos.1.9) are
mounted sideways with the selftapping screw pan head 4,8 x 45
(S13).
The rear gable is assembled in the same way!!!
Only rear gable!
to step 7:
Slide before mounting the crossbar
required hex screws M6 x 16 (S5)
into the profile of the crossbar
(pos.1.8 und 1.9).
The crossbar in the rear gable
is used the same height as the
existing crossbar. Attachment is to
the connecting plate (V10).
connecting
plate (V10)
crossbar
(Pos.1.8)
az
in
g
Now comes the glazing
(787 x 728 mm).
The remaining opening is later
closed by the supplied rear window.
gl
step 7:
11
You should be careful:
T-seals (V25) for all doors and windows
(total: 15 meters)
Attention! When the roof window for
pushing into the ridge the T-seal at
this side omit!!!
In the door area the hose section(V14)
is pressed into the soil profile. (As a
stop/seal to protect from dirt into the
soil profile).
Attention! In the bottom door is
first pressed the seal, and only
then will the rectangular tube
screwed!
Profiles for roof windows (per roof window)
overview
numlength in mm
ber
pos. description
4.1
roof window profile
2
541
4.2
roof window profile
2
953
Content accessories bag roof window (per roof window)
overview
pos. description/item number
*
V25 T-seal
item no 9999 0032
V13 corner with grub screw, internal hex and flat point
numlength in mm
ber
2
641
1
1052
4
item no 9999 0070
V21 allen key
1
item no 9999 0056
S12/ hexagonal screw M6 x 12
S1 nut M6
V24 corner bracket/roof window
item no 9999 0124
4
item no 9999 0005
* Note: The seal is bundled in one strand for all doors and windows, please cut accordingly.
12
3
item no 9999 0128
Assembly roof window
corner with grub
screw (V13)
corner bracket/roof window (V24)
window profil (pos.4.2)
(Pull in this profile no seal!)
Recommendation!
It is advisable to seal up around the window and the corner
bracket, thus no moisture can occur.
Attention: In the bottom cross profile inserting two hex
screws M6 x 12 (S12) for the window opener!
window profil (pos. 4.1)
window profil (pos. 4.1)
First you screw three profiles, then use the glazing and finally
attach the fourth profile.
window profile (pos. 4.2)
automatic roof window opener
Mounting roof window
wrong!!!
right
Please push the roof window from the gable
side into the ridge and slide in position.
Automatic window opener mount.
13
Insertion of the seal in the roof window area
pos. 4.1
Please insert all the 4 plastic
corner connectors with silicone and seal the transitions
cleanly (
).
▲
cross-section
of the seal
▲
▲
pos. 4.1
pos. 3.2
length: 2,3 m
The seal is inserted as the sketch above.
Attention: Seal does not cut into the corners! Important!
The transitions of the glazing and the corner bracket/roof window to roof
it with silicone →
window profile, please seal
see sketch.
Here you need seal all around (
▲
▲
▲
side rung
pos. 2.3
crossbar
pos. 3.2
window profile
pos. 4.1 und 4.2
14
)!
Parts window opener
1
2
3
4
5
window opener
pressure cylinder
cotter pin
mounting plate window profile
mounting plate crossbar
3
1
4
2
5
User guide - window opener Assembly instructions:
1. Check whether the greenhouse window can open and close freely and unhinderedly.
Please remove from other manufacturers in advance the existing hand openers.
2. First install the window opener with the mounting plate (4) to the roof window profile (pos. 4.2).
3. Choose from the mounting plate (5) the middle hole and attach it to the cross rung (pos.3.2)
below the roof window.
4. The pressure cylinder at the upper end of threaded device secure with the cotter pin in the
t-coupling (upper hole).
Ajustment:
The window opener needed after the assembly about 3 - 4 hours to adjust the temperature in
the greenhouse. The more you screw the pressure cylinder into the threaded device, the earlier and more highly opens the window. Do you want earlier/higher opening, turn the pressure
cylinder clockwise. In a later/lower opening counter-clockwise, with one turn is about 0,5°C.
Please keep in mind that can vary the temperature in your greenhouse and several window
openers have small tolerances.
Winter-storage:
If the greenhouse is not "frost-free" hold, we recommend you to remove the entire window opener or only the pressure cylinder. Please keep the window opener in a dry or frost-free place.
Before reassembly in the spring especially the cylinder rod and the cylinder threads are greased to check if it is. The cylinder rod check for ease of movement, please.
15
Profiles for divided revolving door - bottom overview
numlength in mm
ber
pos. description
5.3.1 door profile bottom
1
700
5.6
door profile left
with hole for sash lock
1
692
5.7
door profile right
with hinge hole
1
692
5.9
door profile top
with transverse hole
1
700
5.8
square tube
with transverse hole
1
740
number
length in mm
Content accessories bag divided revolving door - bottom overview
pos. description
V51 metal hinge, black
2
item no 9999 0358
V28 sash lock
1
item no 9999 0023
V29 QR-stopper 30 x 30 x 1,5-2
2
item no 9999 0099
*
V25 T-seal
item no 9999 0032
self-tapping screw countersunk head 4,8 x 25
S18 (hinges)
2
2
8
item no 9999 0163
self-tapping screw countersunk head 4,2 x 45
S17 (doors)
4
item no 9999 0160
self-tapping screw countersunk head 3,5 x 22
S19 (sash
lock)
2
item no 9999 0152
S6
self-tapping screw pan head 3,5 x 38 (square tube)
2
item no 9999 0138
V32 glazing block 30 x 10 x 4
V30/
corner bracket door profile
V31
2
left - item no 9999 0009
right - item no 9999 0011
* Note: The seal is bundled in one strand for all doors and windows, please cut accordingly.
16
4
710
744
Assembly - divided revolving door - bottom view from outside
Place the profile like the image on a flat underground (possibly on cardboard or something
similar).
Square tube and door
profile top screw with
self-tapping screw pan
head 3,5 x 38 (S6).
Attention:
Move before sealing.
(see sketch!)
corner bracket door profile
(V30/V31)
QR-stopper
(V29)
square tube (pos. 5.8)
door profile right (pos. 5.7)
sash lock (V28)
with self-tapping screw
countersunk
head 3,5 x 22
(S19) scews.
door profile left (pos. 5.6)
door profile top (pos. 5.9)
glazing block (V32)
self-tapping screw countersunk head 4,2 x 45 (S17)
door profile bottom (pos. 5.3.1)
* Note: The seal is bundled in one strand for all doors and windows, please cut accordingly.
17
Profiles for divided revolving door - top overview
pos. description
5.1
door profile left
5.2
door profile right
5.3
door profile top
with hinge hole
with hole for lockable door
handle
5.4.1 crossbar
number/length in mm
Riga S
Riga
1
1
1081
1264
1
1
1081
1264
1
1
700
700
1
1
700
700
Content accessories bag - divided revolving door - top
overview
number/length in mm
Riga S
Riga
pos. description
V52 door handle, lockable
outside - item no 9999 0035
inside - item no 9999 0244
self-tapping screw countersunk head 4,2 x 45
S17 (door)
1
1
6
6
2
2
2
710
2
1112
2
710
2
1295
2
2
8
8
1
1
2
2
1
1
1
1
2
2
item no 9999 0160
V32 glazing block 30 x 10 x 4
*
V25 T-seal
item no 9999 0032
V51 metal hinge, black
item no 9999 0358
screw countersunk head 4,8 x 25
S18 self-tapping
(hinge)
item no 9999 0163
V28 sash lock, small
item no 9999 0023
screw countersunk head 3,5 x 22
S19 self-tapping
(sash lock)
item no 9999 0152
V33 door locking device
item no 9999 0230
self drill, screw counters head 3,5 x 13
S22 wing-type
(door stop)
item no 9999 0189
V30/
corner bracket door profile
V31
left - item no 9999 0009
right - item no 9999 0011
* Note: The seal is bundled in one strand or all doors and windows, please cut accordingly.
18
Assembly - divided revolving door - top view from outside
Place the profiles like the image on a flat underground (possibly on cardboard or something
similar).
corner bracket door profile
(V30/V31)
door profile top (pos. 5.3)
door profile right (pos.5.2)
Assembly o door locking
2.
door profile left (pos.5.1)
1.
3.
4.
glazing block with silicone fix in position
crossbar (pos.5.4.1)
self-tapping screw countersunk
head 4,2 x 45 (S17)
sash lock (V28) with self-tapping
screw countersunk head 3,5 x 22
(S19) screws
* Note: The seal is bundled in one strand for all doors and windows, please cut accordingly.
19
Profiles for rear window
overview
pos.
description
5.1.2 door profile left
5.2
with hole for sash lock
door profile right
with hinge hole
5.3.1 door profile top
5.4.2 door profile bottom
with hole for window opener
number/length in mm
Riga S
Riga
1
1
1081
1264
1
1
1081
1264
1
1
700
700
1
1
700
700
Content accessories bag - rear window overview
number/length in mm
Riga S
Riga
pos. description
S17
self-tapping screw countersunk head 4,2 x 45
(window)
item no 9999 0160
6
6
2
2
2
710
2
1112
2
710
2
1295
2
2
screw countersunk head 4,8 x 25
S18 self-tapping
(hinges)
10
10
V28 sash lock, small
1
1
screw countersunk head 3,5 x 22
S19 self-tapping
(sash lock)
2
2
V53 fixation of window
1
1
1
1
1
1
screw countersunk head 4,2 x 16
S31 self-tapping
(f. holder V35)
2
2
S2/
S1
hexagonal screw M6 x 30 + nut
1
1
S3/
S4
screw countersunk M6 x 20 +
hex nut - self locking
1
1
1
1
2
2
V32 glazing block 30 x 10 x 4
*
V25 T-seal
item no 9999 0032
V51 metal hinge, black
item no 9999 0358
item no 9999 0163
item no 9999 0023
item no 9999 0152
item no 9999 0079
V34 corner (fixation of window)
item no 9999 0094
V35 holder (fixation of window)
item no 9999 0002
item no 9999 0157
item no 9999 0126 + 9999 0128
item no 9999 0170 + 9999 0151
S20 knurled nut - white
item no 9999 0025
V30/
corner bracket door profile
V31
left - item no 9999 0009
right - item no 9999 0011
* Note: The seal is bundled in one strand for all doors and windows, please cut accordingly.
20
Assembly - rear window view from outside
sash lock, small (V28)
with self-tapping screw
countersunk 3,5 x 22
(S19) screws
door profile right (pos. 5.2)
door profile left (pos. 5.1.2)
door profile top (pos. 5.3.1)
glazing block with silicone fix in position
self-tapping screw
countersunk head
4,2 x 45 (S17)
crossbar (pos. 5.4.2)
openers for rear
window
window fixation with
self-tapping countersunk screw 4,2 x 16
(S31) screw
* Note: The seal is bundled in one strand for all doors and windows, please cut accordingly.
21
Assembly procedure - eaves ATTENTION! When using a foundation frame assemble in advance on this soil profile (see page 5, 6)
step 8
to step 8:
First, the lateral soil profiles on the
corner bracket on the gable attach.
)
2.1
s.
po et
(
file ack
pro er br
l
i
so corn
to
corner bracket (V12) screwed with
self-tapping screw pan head
4,2 x 13 (S9).
slid
e
to step 9:
step 9
ridge profile (pos. 3.3) at the gable and
end plate (V11) screw with self-tapping
screw pan head 4,2 x 13 (S9)
(p
fil
rid
g
Now you need several hands or
corresponding aids.
.3)
.3
os
Gable upright, hold and secure
support.
ro
ep
The ridge profile (pos. 3.3) now
introduce into the existing grooves/
slots of the gable, so that the
profiles is flush with the front.
Now screw the end plate (V11) with
self-tapping screw pan head 4,2 x
13 (S9).
ends support or
hold up it
to step 10:
step 10
Slide the side glazing in the soil profiile and rand rung and threading.
tip:
please solve the foil only at the
margin!
insert the side glazing and
thread
22
Assembly procedure - eaves ATTENTION! When using a foundation frame assemble in advance on this soil profile (see page 5, 6)
step 11
to step 11:
The side rung (pos. 2.3) above into
the ridge profile and below into the
soil profile to glazing insert it. There,
the plate is threading.
If neccessary, timber and plastic
hammer to get help.
Tip:
Greasing plastic gliders perhaps a
little!
shown enlarged side
rung (pos. 2.3)
step 12
to step 12:
Insert further side glazing and
rungs.
The connecting plate (V4) from
inside screwed with screw hex M6 x
16 and nut M6.
step 13
to step 13:
Insert the remaining plates and
rungs now.
23
Assembly procedure - eaves ATTENTION! When using a foundation frame assemble advance on this soil profile (see page 5, 6)
to step 14:
step 14
The door gable is pre-mounted and
screwed.
For added stability must now
mounting inside corner (V1) be
attached. Use the self-tapping screw
pan head 4,2 x 13 (S9).
to step 15:
step 15
Install door and window.
Instructions, see page 12-21.
Mounting roof window
wrong!!!
right
step 16
to step 16:
Represented
for the better
representation
plates cut.
The stabilization angle (pos 3.4)
become on both sides from inside
to the side rung with screw M6 x 16,
nut M6 and washer A6,4 screwed.
The angles are also profiles for
rearward tables and shelves (see
separate instructions).
24
glas plan with ISO-cellular sheets 10 mm
gable
above
gable below
gable
triangular
door/
window
div. revolv. rear gable
door/bottom below
side plate
roof
window
below roof
window
b
b
b
b
b
b
b
b
b
type of
house
a
a
a
number
size (a x b)
number
size (a x b)
number
size (a x b)
number
size (a x b)
1
724 x 676
1
787 x 728
3
1048 x 2634
1
974 x 565
1
1048 x 1984
2
724 x 1031
1
724 x 676
1
787 x 728
5
1048 x 2634
1
974 x 565
1
1048 x 1984
2
779 x 239
2
724 x 1031
1
724 x 676
1
787 x 728
6
1048 x 2634
2
974 x 565
2
1048 x 1984
4
1048 x 728
2
779 x 239
2
724 x 1215
1
724 x 676
1
787 x 728
5
1048 x 3000
1
974 x 565
1
1048 x 2345
4
1048 x 1319
4
1048 x 728
2
779 x 239
2
724 x 1215
1
724 x 676
1
787 x 728
6
1048 x 3000
2
974 x 565
2
1048 x 2345
4
1048 x 1319
4
1048 x 728
2
779 x 239
2
724 x 1215
1
724 x 676
1
787 x 728
6
1048 x 3000
4
974 x 565
4
1048 x 2345
a
a
a
number
size (a x b)
number
size (a x b)
Riga II S
4
730 x 1135
Riga III S
Riga IV S
a
number
size (a x b)
number
size (a x b)
number
size (a x b)
4
730 x 728
2
779 x 239
2
724 x 1031
4
730 x 1135
4
730 x 728
2
779 x 239
4
730 x 1135
4
730 x 728
Riga III
4
1048 x 1319
Riga IV
Riga V
25
a
a

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement