Kenroy Home 93243CH Instructions / Assembly

 MODEL: 93243CH
PACKING DIAGRAM
STYROFOAM:
LA a
IXTURE BODY
CANOPY ASSEMBLY
AND PARTS
mover: 9 324 3CH
|- —cAnoPY ASSEMBLY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
A
O. ———FINIAL
KNO (2 PCS) READ INSTRUCTIONS ALL THE WAY THROUGH PRIOR TO ASSEMBLY.
THIS FIXTURE SHOULD TAKE APPROXIMATELY 5 MINUTES TO
ASSEMBLE.
MAKE SURE ALL PARTS ARE FIRMLY TIGHTENED.
TOOLS: YOU WILL NEED THE FOLLOWING TOOLS OR
EQUIPMENT: LADDER, SCREWDRIVER, WIRE CUTTERS.
UNPACK THE FIXTURE
YOU SHOULD HAVE RECEIVED THE FOLLOWING PARTS IN THE
PACKAGE: CANOPY AND FIXTURE BODY. TO PROTECT THE
FINISH, PLACE ALL PARTS ON A SOFT SURFACE.
—CORD
MOUNTING HARDWARE PACKAGE:
(2) 8-32 x 1-1/4” SCREWS AND (3) WIRE CONNECTORS.
FIXTURE ASSEMBLY
1. REMOVE MOUNTING PLATE FROM TOP OF THE CANOPY BY
UNSCREWING (2) FINIALS.
2. LOOSE THE KNOB ON BOTTOM OF CANOPY AND ADJUST
THE CORD LENGTH, THEN SECURE THE CORD TO CANOPY BY
TIGHTENING THE KNOB.
3. CUT OFF THE CORD TO KEEP THE CORD 12” LONGER
I THAN THE LENGTH THAT YOU WANT.
4. SPLIT THE END OF THE POWER SUPPLY WIRE 3-1/2"
FROM THE END AND STRIP THE PLASTIC COVER OFF THE
WIRE ABOUT 1/2”.
5. INSTALL A 60 WATT MAX. MEDIUM BASE TYPE "A” BULB
(NOT INCLUDED) INTO THE SOCKET.
6. COMPLETE INSTALLATION INSTRUCTIONS ON NEXT PAGE.
FIXTURE
BODY
Y
Y
SOCKET
07/2014 93243CH ASSEMBLY INSTRUCTIONS
-— OUTLET BOX
SUPPLY GROUND WIRE N
I 7 — N WHITE SUPPLY WIRE
BLACK SUPPLY WIRE - |
RÉ FA WIRE CONNECTORS,
N I (3 PCS)
CEILING -— AN cf
|
| |
SILVER FIXTURE WIRE WHITE FIXTURE WIRE
| |
8—32 SCREWS, Е GREEN GROUND WIRE
SUPPLIED WITH BOX al E MOUNTING PLATE
8—32 x 1” SCREW - Е GREEN GROUND SCREW
- CANOPY
O O- FINIAL (2 PCS)
- CORD
A
INSTALLATION INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
CAUTION
TO AVOID POSSIBLE ELECTRIC SHOCK, MAKE SURE THE ELECTRICITY IS SHUT OFF AT THE MAIN PANEL. IF YOU
ARE REPLACING AN EXISTING FIXTURE, FIRSTLY, TURN THE FIXTURE OFF. NEXT, TURN THE WALL SWITCH OFF.
FINALLY, GO TO THE MAIN FUSE OR BREAKER BOX IN YOUR HOME. TURN THE FUSE OR BREAKER TO THE OFF
POSITION. SOME TYPES OF FUSES MUST BE UNSCREWED TO SHUT OFF THE POWER.
* ALL WIRING MUST BE DONE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRIC CODES.
** IF YOU ARE NOT FAMILIAR WITH WIRING, YOU SHOULD USE A QUALIFIED ELECTRICIAN.
*** THIS FIXTURE IS INTENDED TO BE MOUNTED TO A UL LISTED OUTLET BOX CAPABLE OF SUPPORTING THE
FIXTURE.
COMPLETE FIXTURE ASSEMBLY INSTRUCTIONS FIRST (SEE PREVIOUS).
1. ATTACH THE MOUNTING PLATE TO THE CEILING OUTLET BOX USING THE TWO SCREWS PROVIDED WITH THE
OUTLET BOX. (NOTE: IF THE SCREWS WITH THE OUTLET BOX ARE TOO SHORT, USE THE (2) 8-32 x 1-1/4"
SCREWS PROVIDED IN THE MOUNTING HARDWARE PACKAGE).
2. CONNECT THE WHITE FIXTURE WIRE TO THE WHITE SUPPLY WIRE IN THE OUTLET BOX USING THE TWIST—ON
WIRE CONNECTORS PROVIDED. CONNECT THE SILVER FIXTURE WIRE TO THE BLACK SUPPLY WIRE IN THE SAME
MANNER. INSTALL THE GREEN GROUND WIRE UNDER THE GREEN GROUND SCREW ON THE MOUNTING PLATE
THEN CONNECT THE GREEN GROUND WIRE TO THE SUPPLY GROUND WIRE IN THE OUTLET BOX USING THE
TWIST—ON WIRE CONNECTOR PROVIDED.
3. TUCK THE WIRES CAREFULLY INSIDE THE OUTLET BOX. SPREAD THE ELECTRICAL SPLICES SO THAT THE
BLACK WIRES ARE ON ONE SIDE OF THE OUTLET BOX AND THE WHITE WIRES ARE ON THE OTHER SIDE.
4. RAISE THE FIXTURE TO THE CEILING AND SECURE IN PLACE WITH (2) BALL FINIALS.
5. RESTORE POWER, YOUR FIXTURE IS NOW READY FOR USE.
07/2014 93243CH INSTALLATION