Kenroy Home 10180BS installation Guide

 y |
CROSSBAR чм :
CANOPY
—
—
Aa —] A a
ДЕЙ
Xx eV NV
FIXTURE
BODY
HAR
LIGHT CLUSTE
=
STABILIZER———
WIRE CONNECTOR
(3 PCS)
IPPLE
CREW
COLLAR NUT
CREW
COLLAR LOOP
HAIN
HAIN LOOP
| on SOCKET
SOCKET
RING
OWER SOCKET
NIPPLE
GLASS SHADE
—«———10180BSES
(REPLACEMENT
PART)
al}
METAL WASHER
OD NUT
[F=———0NT
CJ
FINIAL
AVAILABLE PART IS:
10180BSGS (GLASS SHADE)
12/08
moEL: 101 80BS
ASSEMBLY INSTRUCTIONS —1
READ AND SAVE THESE INSTRUCTIONS
TOOLS: YOU WILL NEED THE FOLLOWING TOOLS OR
EQUIPMENT: LADDER, SCREWDRIVER, ADJUSTABLE WRENCH,
WIRE CUTTERS AND PLIERS.
UNPACK THE FIXTURE
YOU SHOULD HAVE RECEIVED THE FOLLOWING PARTS IN
THE PACKAGE: CANOPY, CHAIN, FIXTURE BODY, HARP,
SOCKET RING, LIGHT CLUSTER, NIPPLE, STABILIZER, METAL
WASHER, NUT, FONT, FINIAL. TO PROTECT THE FINISH,
PLACE ALL PARTS ON A SOFT SURFACE.
MOUNTING HARDWARE PACKAGE:
EXTRA CANOPY, (2) SMALL FINIALS, (2) EXTRA METAL
WASHERS, SCREW COLLAR LOOP, SCREW COLLAR NUT, (2)
NUTS, NIPPLE, (2) 8-32 X 1-1/4" SCREWS, CROSSBAR,
GREEN GROUND SCREW AND (3) WIRE CONNECTORS.
NOTE: IF MOUNT AS UP PENDANT, PROCEED TO THE
INSTRUCTIONS—1 AS BELOW, IF MOUNT AS DOWN
PENDANT, PROCEED TO THE INSTRUCTIONS—2 ON THE
NEXT PAGE, IF MOUNT AS SEMI-FLUSH, PROCEED TO THE
INSTRUCTIONS—3 ON THE NEXT PAGE.
FIXTURE ASSEMBLY
1. DETERMINE THE LENGTH OF CHAIN REQUIRED TO HANG
THE FIXTURE AT THE DESIRED HEIGHT. USING PLIERS,
OPEN ONE END LINK OF CHAIN AND ATTACH TO THE CHAIN
LOOP ON TOP OF THE FIXTURE. REMOVE OR ADD CHAIN
AS DESIRED AT THIS TIME. LACE FIXTURE WIRE AND
GROUND WIRE UP THROUGH EVERY OTHER LINK OF CHAIN.
TO SPREAD A LINK OF CHAIN
USE A PAIR OF PLIERS AND A SCREWDRIVER AS
SHOWN ABOVE, BEING CAREFUL TO WRAP THE
JAWS OF THE PLIERS WITH CLOTH TO PROTECT
THE FINISH OF THE CHAIN.
¥*STOP** COMPLETE INSTALLATION
INSTRUCTIONS ON NEXT PAGE BEFORE
CONTINUING TO FINAL ASSEMBLY.
FINAL ASSEMBLY
1. SECURE HARP TO UPPER SOCKET WITH SOCKET RING.
2. SCREW LIGHT CLUSTER INTO UPPER SOCKET.
3. SCREW NIPPLE TO BOTTOM OF HARP.
4. SLIDE STABILIZER, GLASS SHADE OVER THE NIPPLE,
THEN SECURE WITH A METAL WASHER AND A NUT.
5. SLIDE FONT OVER END OF THE NIPPLE AND SECURE
WITH FINIAL.
6. INSTALL A 75 WATT MAX. MEDIUM BASE TYPE "A" BULB
(NOT INCLUDED) INTO EACH LOWER SOCKET.
7. RESTORE POWER, YOUR NEW FIXTURE IS NOW READY
FOR USE.
10180BS INSTRUCTIONS (PAGE 1 / 5)
WIRE CONNECTOR
(3 PCS)
IPPLE
= CREW
e COLLAR NUT
CREW
COLLAR LOOP
FIXTURE
BODY
SOCKET
| GLASS SHADE
«——10180BSCS
(REPLACEMENT
PART)
- METAL WASHER
ENE — SOCKET RING
AVAILABLE PART IS:
10180BSGS (GLASS SHADE)
12/08
moEL: 101 80BS
ASSEMBLY INSTRUCTIONS—2
READ AND SAVE THESE INSTRUCTIONS
TOOLS: YOU WILL NEED THE FOLLOWING TOOLS OR
EQUIPMENT: LADDER, SCREWDRIVER, ADJUSTABLE WRENCH,
WIRE CUTTERS AND PLIERS.
UNPACK THE FIXTURE
YOU SHOULD HAVE RECEIVED THE FOLLOWING PARTS IN
THE PACKAGE: CANOPY, CHAIN, FIXTURE BODY, HARP,
SOCKET RING, LIGHT CLUSTER, NIPPLE, STABILIZER, METAL
WASHER, NUT, FONT, FINIAL. TO PROTECT THE FINISH,
PLACE ALL PARTS ON A SOFT SURFACE.
MOUNTING HARDWARE PACKAGE:
EXTRA CANOPY, (2) SMALL FINIALS, (2) EXTRA METAL
WASHERS, SCREW COLLAR LOOP, SCREW COLLAR NUT, (2)
NUTS, NIPPLE, (2) 8-32 X 1-1/4" SCREWS, CROSSBAR,
GREEN GROUND SCREW AND (3) WIRE CONNECTORS.
NOTE: IF MOUNT AS DOWN PENDANT, PROCEED TO THE
INSTRUCTIONS AS BELOW, IF MOUNT AS UP PENDANT,
PROCEED TO THE INSTRUCTIONS—1 ON THE PREVIOUS
PAGE, IF MOUNT AS SEMI-FLUSH, PROCEED TO THE
INSTRUCTIONS—3 ON THE NEXT PAGE.
FIXTURE ASSEMBLY
1. DETERMINE THE LENGTH OF CHAIN REQUIRED TO HANG
THE FIXTURE AT THE DESIRED HEIGHT. USING PLIERS,
OPEN ONE END LINK OF CHAIN AND ATTACH TO THE CHAIN
LOOP ON TOP OF THE FIXTURE. REMOVE OR ADD CHAIN
AS DESIRED AT THIS TIME. LACE FIXTURE WIRE AND
GROUND WIRE UP THROUGH EVERY OTHER LINK OF CHAIN.
TO SPREAD A LINK OF CHAIN
USE A PAIR OF PLIERS AND A SCREWDRIVER AS
SHOWN ABOVE, BEING CAREFUL TO WRAP THE
JAWS OF THE PLIERS WITH CLOTH TO PROTECT
THE FINISH OF THE CHAIN.
¥*STOP** COMPLETE INSTALLATION
INSTRUCTIONS ON NEXT PAGE BEFORE
CONTINUING TO FINAL ASSEMBLY.
FINAL ASSEMBLY
1. RAISE GLASS SHADE OVER THE SOCKET, THEN SECURE
WITH METAL WASHER AND SOCKET RING.
2. INSTALL A 150 WATT MAX. MEDIUM BASE TYPE "A" BULB
(NOT INCLUDED) INTO SOCKET.
3. RESTORE POWER, YOUR NEW FIXTURE IS NOW READY
FOR USE.
10180BS INSTRUCTIONS (PAGE 2 / 5)
(can LOOP
(REMOVE)
FIXTURE
BODY
NUT——— a»
- METAL WASHER
METAL WASHER -
| |+—EXTRA CANOPY
CORD -
8 4 he SMALL FINIAL
NIPPLE : “a (2 PCS)
—] —
FIXTURE
BODY
! “am SOCKET
HAR SOCKET
RING
LIGHT CLUSTE OWER SOCKET
É NIPPLE
STABILIZER— —
GLASS SHADE
-———10180BSGS
| (REPLACEMENT
PART)
- METAL WASHER
= NUT
[РОМ
о- FINIAL
12/08
moEL: 101 80BS
ASSEMBLY INSTRUCTIONS—3
READ AND SAVE THESE INSTRUCTIONS
TOOLS: YOU WILL NEED THE FOLLOWING TOOLS OR
EQUIPMENT: LADDER, SCREWDRIVER, ADJUSTABLE WRENCH,
WIRE CUTTERS AND PLIERS.
UNPACK THE FIXTURE
YOU SHOULD HAVE RECEIVED THE FOLLOWING PARTS IN
THE PACKAGE: CANOPY, CHAIN, FIXTURE BODY, HARP,
SOCKET RING, LIGHT CLUSTER, NIPPLE, STABILIZER, METAL
WASHER, NUT, FONT, FINIAL. TO PROTECT THE FINISH,
PLACE ALL PARTS ON A SOFT SURFACE.
MOUNTING HARDWARE PACKAGE:
EXTRA CANOPY, (2) SMALL FINIALS, (2) EXTRA METAL
WASHERS, SCREW COLLAR LOOP, SCREW COLLAR NUT, (2)
NUTS, NIPPLE, (2) 8-32 X 1-1/4" SCREWS, CROSSBAR,
GREEN GROUND SCREW AND (3) WIRE CONNECTORS.
NOTE: IF MOUNT AS SEMI-FLUSH, PROCEED TO THE
INSTRUCTIONS AS BELOW, IF MOUNT AS UP PENDANT,
PROCEED TO THE INSTRUCTIONS—1 ON THE PREVIOUS
PAGE, IF MOUNT AS DOWN PENDANT, PROCEED TO THE
INSTRUCTIONS—2 ON THE PREVIOUS PAGE.
FIXTURE ASSEMBLY
1. REMOVE CHAIN LOOP FROM FIXTURE BODY.
2. CUT THE CORD, LEAVING AT LEAST 15.2 CM (6”)
LENGTH ABOVE NIPPLE FOR ELECTRICAL CONNECTTING.
3. PLACE THE EXTRA CANOPY OVER THE NIPPLE ON TOP
OF FIXTURE BODY, THEN SECURE WITH (2) WASHERS AND
A NUT.
¥*STOP** COMPLETE INSTALLATION
INSTRUCTIONS—2 ON NEXT PAGE BEFORE
CONTINUING TO FINAL ASSEMBLY.
FINAL ASSEMBLY
1. SECURE HARP TO UPPER SOCKET WITH SOCKET RING.
2. SCREW LIGHT CLUSTER INTO UPPER SOCKET.
3. SCREW NIPPLE TO BOTTOM OF HARP.
4. SLIDE STABILIZER, GLASS SHADE OVER THE NIPPLE,
THEN SECURE WITH A METAL WASHER AND A NUT.
5. SLIDE FONT OVER END OF THE NIPPLE AND SECURE
WITH FINIAL.
6. INSTALL A 75 WATT MAX. MEDIUM BASE TYPE "A" BULB
(NOT INCLUDED) INTO EACH LOWER SOCKET.
7. RESTORE POWER, YOUR NEW FIXTURE IS NOW READY
FOR USE.
AVAILABLE PART IS:
10180BSGS (GLASS SHADE)
10180BS INSTRUCTIONS (PAGE 3 / 5)
SUPPLY GROUND WIRE = - | OUTLET BOX
< WHITE
BLACK SUPPLY WIRE - SUPPLY WIRE
CEILING A a WIRE CONNECTORS
BLACK OR SMOOTH — — | | (3) REQUIRED
FIXTURE WIRE: '
WHITE OR RIBBED
8—32 SCREWS, FIXTURE WIRE
SUPPLIED WITH BOX
All
ROSSBAR
NIPPLE -
IXTURE GROUND WIRE
CANOPY >
| REEN GROUND SCREW
SCREW COLLAR NUT:
SCREW COLLAR LOOP
CHAIN
INSTALLATION INSTRUCTIONS -1
READ AND SAVE THESE INSTRUCTIONS
CAUTION
TO AVOID POSSIBLE ELECTRIC SHOCK, MAKE SURE THE ELECTRICITY IS SHUT OFF AT THE MAIN PANEL. IF YOU
ARE REPLACING AN EXISTING FIXTURE, FIRSTLY, TURN THE FIXTURE OFF. NEXT, TURN THE WALL SWITCH OFF.
FINALLY, GO TO THE MAIN FUSE OR BREAKER BOX IN YOUR HOME. TURN THE FUSE OR BREAKER TO THE OFF
POSITION. SOME TYPES OF FUSES MUST BE UNSCREWED TO SHUT OFF THE POWER.
* ALL WIRING MUST BE DONE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRIC CODES. IF YOU ARE NOT
FAMILIAR WITH WIRING, YOU SHOULD USE A QUALIFIED ELECTRICIAN.
** THIS FIXTURE IS INTENDED TO BE MOUNTED TO A UL LISTED OUTLET BOX CAPABLE OF SUPPORTING THE
FIXTURE.
1. ATTACH THE CROSS BAR TO THE CEILING OUTLET BOX USING THE TWO SCREWS PROVIDED WITH THE
OUTLET BOX. (NOTE: IF THE SCREWS WITH THE OUTLET BOX ARE TOO SHORT, USE THE (2) 8-32 x 1-1/4"
SCREWS PROVIDED IN THE MOUNTING HARDWARE PACKAGE). NEXT, SCREW THE SCREW COLLAR LOOP ONTO
THE NIPPLE AND THEN SCREW THE NIPPLE INTO THE CROSS BAR.
2. SLIDE THE SCREW COLLAR NUT AND THEN THE CANOPY ONTO THE END OF THE CHAIN. THEN FASTEN THE
END LINK OF CHAIN TO THE SCREW COLLAR LOOP.
3. INSERT THE FIXTURE WIRE AND THE GROUND WIRE UP THROUGH THE NIPPLE. CONNECT THE WHITE OR
RIBBED FIXTURE WIRE TO THE WHITE SUPPLY WIRE IN THE OUTLET BOX USING THE TWIST—ON WIRE
CONNECTORS PROVIDED. CONNECT THE BLACK OR SMOOTH FIXTURE WIRE TO THE BLACK SUPPLY WIRE IN THE
SAME MANNER. INSTALL THE FIXTURE GROUND WIRE UNDER THE GREEN GROUND SCREW ON THE CROSSBAR
THEN CONNECT THE FIXTURE GROUND WIRE TO THE SUPPLY GROUND WIRE IN THE OUTLET BOX USING THE
TWIST—ON WIRE CONNECTOR PROVIDED.
4. TUCK THE WIRES CAREFULLY INSIDE THE OUTLET BOX. SPREAD THE ELECTRICAL SPLICES SO THAT THE
BLACK WIRES ARE ON ONE SIDE OF THE OUTLET BOX AND THE WHITE WIRES ARE ON THE OTHER SIDE. NEXT
RAISE THE CANOPY TO THE CEILING AND SECURE IN PLACE BY SCREWING THE SCREW COLLAR NUT ONTO THE
SCREW COLLAR LOOP.
5. SEE PREVIOUS PAGE FOR FINAL ASSEMBLY INSTRUCTIONS.
eL 12/08 10180BS INSTRUCTIONS (PAGE 4 / 5)
OUTLET BOX
SUPPLY GROUND wee |___
BLACK SUPPLY WIRE
CEILING _
BLACK OR SMOOTH
FIXTURE WIRE
8—32 SCREWS, - : WHITE OR RIBBED
SUPPLIED WITH BOX Eo com E FIXTURE WIRE
WHITE SUPPLY WIRE
WIRE CONNECTORS,
(3) REQUIRED
CROSS BAR
FIXTURE GROUND WIRE
GREEN GROUND SCREW
CANOPY >
SMALL FINIAL (2 PCS)
INSTALLATION INSTRUCTIONS—2
READ AND SAVE THESE INSTRUCTIONS
CAUTION: TO AVOID POSSIBLE ELECTRIC SHOCK, MAKE SURE THE ELECTRICITY IS SHUT OFF AT THE MAIN
PANEL. IF YOU ARE REPLACING AN EXISTING FIXTURE, FIRSTLY, TURN THE FIXTURE OFF. NEXT, TURN THE
WALL SWITCH OFF. FINALLY, GO TO THE MAIN FUSE OR BREAKER BOX IN YOUR HOME. TURN THE FUSE OR
BREAKER TO THE OFF POSITION. SOME TYPES OF FUSES MUST BE UNSCREWED TO SHUT OFF THE POWER.
* ALL WIRING MUST BE DONE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRIC CODES.
** IE YOU DO NOT HAVE ELECTRICAL WIRING EXPERIENCE, HAVE YOUR FIXTURE INSTALLED BY A QUALIFIED
LICENSED ELECTRICIAN.
***THIS FIXTURE IS TO BE MOUNTED TO A UL LISTED OUTLET BOX CAPABLE OF SUPPORTING THE WEIGHT OF
THIS FIXTURE. THE OUTLET BOX MUST BE DIRECTLY SUPPORTED BY THE BUILDING STRUCTURE.
COMPLETE FIXTURE ASSEMBLY INSTRUCTIONS—3 FIRST ON PREVIOUS PAGE.
1. SCREW (2) 8-32 x 1-1/4" SCREWS INTO THE CROSSBAR MAKING SURE THAT THEY LINE UP WITH THE
HOLES IN THE CANOPY. ATTACH THE CROSS BAR TO THE CEILING OUTLET BOX USING THE TWO SCREWS
PROVIDED WITH THE OUTLET BOX. (NOTE: IF THE SCREWS WITH THE OUTLET BOX ARE TOO SHORT, USE THE
(2) 8-32 x 1-1/4" SCREWS PROVIDED IN THE MOUNTING HARDWARE PACKAGE).
2. INSERT THE FIXTURE WIRE UP THROUGH THE NIPPLE. CONNECT THE WHITE OR RIBBED FIXTURE WIRE TO
THE WHITE SUPPLY WIRE IN THE OUTLET BOX USING THE TWIST—ON WIRE CONNECTORS PROVIDED. CONNECT
THE BLACK OR SMOOTH FIXTURE WIRE TO THE BLACK SUPPLY WIRE IN THE SAME MANNER. INSTALL THE
FIXTURE GROUND WIRE UNDER THE GREEN GROUND SCREW ON THE CROSSBAR THEN CONNECT THE FIXTURE
GROUND WIRE TO THE SUPPLY GROUND WIRE IN THE OUTLET BOX USING THE TWIST—ON WIRE CONNECTOR
PROVIDED.
3. TUCK THE WIRES CAREFULLY INSIDE THE OUTLET BOX. SPREAD THE ELECTRICAL SPLICES SO THAT THE
BLACK WIRES ARE ON ONE SIDE OF THE OUTLET BOX AND THE WHITE WIRES ARE ON THE OTHER SIDE.
4, RAISE THE FIXTURE TO THE CEILING AND SECURE IN PLACE WITH THE (2) SMALL FINIALS.
5. SEE PREVIOUS PAGE FOR FINAL ASSEMBLY INSTRUCTIONS.
® 12/08 10180BS INSTRUCTIONS (PAGE 5 / 5)