Kenroy Home 93323CHC Instructions / Assembly

 MODEL: 93323CHC
PACKING DIAGRAM
ARDBOARD
FIXTURE BODY:
OTHER PARTS
a ANOPY, CHAIN, CHAIN LOOP
— AND MOUNTING PARTS.
|
Cie
SIYROFOAM: 12 KGS.
GLASS SHADE
STYROFOAM: 12 KGS.
= (= WIRE CONNECTOR
DE (3 PCS)
CROSSBAR EN
я IPPLE
CANOPY: —
>]
T CREW
== COLLAR NUT
(1 CREW
(| COLLAR LOOP
)-——can
|
QUICK LINK ||
& HAIN LOOP
AXTURE / ARM (3 PCS)
BODY
HH
ws
NUT
IPPLE
NUT
——=——METAL WASHER
RUBBER WASHER— — ——
GLASS SHADE
(REPLACEMENT — e RUBBER WASHER
PART) — METAL WASHER
NUT:
7 ONT
FINAL —— 1
AVAILABLE PART IS:
93323GS (GLASS SHADE)
03/2014
moDEL: 9 3323CHC
ASSEMBLY INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
READ INSTRUCTIONS ALL THE WAY THROUGH PRIOR TO
ASSEMBLY.
THIS FIXTURE SHOULD TAKE APPROXIMATELY 10 MINUTES TO
ASSEMBLE.
MAKE SURE ALL PARTS ARE FIRMLY TIGHTENED.
TOOLS: YOU WILL NEED THE FOLLOWING TOOLS OR EQUIPMENT:
LADDER, SCREWDRIVER, ADJUSTABLE WRENCH, WIRE CUTTERS
AND PLIERS.
UNPACK THE FIXTURE
YOU SHOULD HAVE RECEIVED THE FOLLOWING PARTS IN THE
PACKAGE: CANOPY, CHAIN, QUICK LINK, CHAIN LOOP, FIXTURE
BODY, NIPPLE, (3) NUTS, (2) RUBBER WASHERS, (2) METAL
WASHERS, FONT AND FINIAL. TO PROTECT THE FINISH, PLACE
ALL PARTS ON A SOFT SURFACE.
MOUNTING HARDWARE PACKAGE:
SCREW COLLAR LOOP, SCREW COLLAR NUT, NUT, NIPPLE, (2)
8-32 X 1-1/4" SCREWS, CROSSBAR, GREEN GROUND SCREW
AND (3) WIRE CONNECTORS.
FIXTURE ASSEMBLY
1. SCREW THE CHAIN LOOP TO TOP OF THE FIXTURE BODY.
2. DETERMINE THE LENGTH OF CHAIN REQUIRED TO HANG THE
FIXTURE AT THE DESIRE HEIGHT, REMOVE OR ADD CHAIN AS
DESIRED. USING PLIERS, OPEN ONE END LINK OF CHAIN AND
ATTACH TO SCREW COLLAR LOOP, ATTACH THE QUICK LINK TO
END LINK OF THE CHAIN AND ATTACH THE QUICK LINK TO CHAIN
LOOP AND THEN SECURE WITH SMALL NUT. THREAD FIXTURE
WIRE AND GROUND WIRE UP THROUGH EVERY OTHER LINK OF
CHAIN.
TO OPEN A CHAIN LINK
Use a pair of pliers and a screwdriver
as shown above to open a chain link.
Wrap the jaws of the pliers with cloth
to protect the finish of the chain.
**STOP** COMPLETE INSTALLATION
INSTRUCTIONS ON NEXT PAGE BEFORE
CONTINUING TO FINAL ASSEMBLY.
FINAL ASSEMBLY
1. SCREW NIPPLE TO BOTTOM OF THE FIXTURE BODY AND
SECURE WITH A NUT.
2. SLIDE METAL WASHER, RUBBER WASHER AND GLASS SHADE
OVER THE NIPPLE, THEN SECURE WITH A RUBBER WASHER,
METAL WASHER AND A NUT.
3. SLIDE THE FONT OVER END OF THE NIPPLE AND SECURE
WITH FINIAL.
4, INSTALL A 60 WATT MAX. MEDIUM BASE TYPE "A" BULB (NOT
INCLUDED) INTO EACH SOCKET.
5. RESTORE POWER. YOUR FIXTURE IS NOW READY FOR USE.
93323CHC ASSEMBLY INSTRUCTIONS
SUPPLY GROUND WIRE = - | OUTLET BOX
< WHITE
BLACK SUPPLY WIRE - SUPPLY WIRE
CEILING A a WIRE CONNECTORS
BLACK OR SMOOTH — — | | (3 PCS)
FIXTURE WIRE
WHITE OR RIBBED
8—32 SCREWS, FIXTURE WIRE
SUPPLIED WITH BOX
All
ROSSBAR
NIPPLE -
IXTURE GROUND WIRE
CANOPY
REEN GROUND SCREW
SCREW COLLAR NUT:
SCREW COLLAR LOOP
CHAIN
INSTALLATION INSTRUCTIONS
READ AND SAVE THESE INSTRUCTIONS
CAUTION
TO AVOID POSSIBLE ELECTRIC SHOCK, MAKE SURE THE ELECTRICITY IS SHUT OFF AT THE MAIN PANEL. IF YOU
ARE REPLACING AN EXISTING FIXTURE, FIRSTLY, TURN THE FIXTURE OFF. NEXT, TURN THE WALL SWITCH OFF.
FINALLY, GO TO THE MAIN FUSE OR BREAKER BOX IN YOUR HOME. TURN THE FUSE OR BREAKER TO THE OFF
POSITION. SOME TYPES OF FUSES MUST BE UNSCREWED TO SHUT OFF THE POWER.
* ALL WIRING MUST BE DONE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRIC CODES. IF YOU ARE NOT
FAMILIAR WITH WIRING, YOU SHOULD USE A QUALIFIED ELECTRICIAN.
** THIS FIXTURE IS INTENDED TO BE MOUNTED TO A UL LISTED OUTLET BOX CAPABLE OF SUPPORTING THE
FIXTURE.
1. ATTACH THE CROSS BAR TO THE CEILING OUTLET BOX USING THE TWO SCREWS PROVIDED WITH THE
OUTLET BOX. (NOTE: IF THE SCREWS WITH THE OUTLET BOX ARE TOO SHORT, USE THE (2) 8-32 x 1-1/4"
SCREWS PROVIDED IN THE MOUNTING HARDWARE PACKAGE). NEXT, SCREW THE SCREW COLLAR LOOP ONTO
THE NIPPLE AND THEN SCREW THE NIPPLE INTO THE CROSS BAR.
2. SLIDE THE SCREW COLLAR NUT AND THEN THE CANOPY ONTO THE END OF THE CHAIN. THEN FASTEN THE
END LINK OF CHAIN TO THE SCREW COLLAR LOOP.
3. INSERT THE FIXTURE WIRE AND THE GROUND WIRE UP THROUGH THE NIPPLE. CONNECT THE WHITE OR
RIBBED FIXTURE WIRE TO THE WHITE SUPPLY WIRE IN THE OUTLET BOX USING THE TWIST—ON WIRE
CONNECTORS PROVIDED. CONNECT THE BLACK OR SMOOTH FIXTURE WIRE TO THE BLACK SUPPLY WIRE IN THE
SAME MANNER. INSTALL THE FIXTURE GROUND WIRE UNDER THE GREEN GROUND SCREW ON THE CROSSBAR
THEN CONNECT THE FIXTURE GROUND WIRE TO THE SUPPLY GROUND WIRE IN THE OUTLET BOX USING THE
TWIST—ON WIRE CONNECTOR PROVIDED.
4. TUCK THE WIRES CAREFULLY INSIDE THE OUTLET BOX. SPREAD THE ELECTRICAL SPLICES SO THAT THE
BLACK WIRES ARE ON ONE SIDE OF THE OUTLET BOX AND THE WHITE WIRES ARE ON THE OTHER SIDE. NEXT
RAISE THE CANOPY TO THE CEILING AND SECURE IN PLACE BY SCREWING THE SCREW COLLAR NUT ONTO THE
SCREW COLLAR LOOP.
5. SEE PREVIOUS PAGE FOR FINAL ASSEMBLY INSTRUCTIONS.
03/2014 93323CHC INSTALLATION