EBN Technology Corp. Service Manual


Add to my manuals
55 Pages

advertisement

EBN Technology Corp. Service Manual | Manualzz
EBN Technology Corp.
Service Manual
MPOS 50 Series
*MPOS50-8B-LX800
March 2007
©Copyright 2007 by EBN Technology Corp. All Rights Reserved.
3/30/2007
1/55
Rev. 1.1
EBN Technology Corp.
Copyright Notice
The information in this document is subject to change without prior notice in order to improve
reliability, design and function and does not represent a commitment on the part of the
manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or documentation,
even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or other
means in any form without prior written permission of the manufacturer.
Trademarks
AMD is a registered trademark of AMD Corporation. Award is registered trademarks of
Phoenix Technologies LTD. Other product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
companies.
3/30/2007
2/55
Rev. 1.1
EBN Technology Corp.
Contents
Chapter 1 Troubleshooting ................................................................................................................. 6
1.1
Symptoms and Solutions ................................................................................................ 6
1.2
BIOS Upgrade ................................................................................................................ 10
Chapter 2: Disassembly, Assembly ................................................................................................. 16
2.1
Main Unit......................................................................................................................... 16
2.1.1
2.1.2
Touch Panel + Touch Screen Holder ................................................................ 16
LCD, AUO 8.4”.................................................................................................... 21
2.1.3
LCD Chassis ....................................................................................................... 22
2.1.4
M/B....................................................................................................................... 23
2.1.5
EMI A/D Cover .................................................................................................... 24
2.1.6
Speaker Module.................................................................................................. 25
2.1.7
Inverter ................................................................................................................ 26
2.1.8
Inverter Cover ..................................................................................................... 27
2.1.9
51 I/O Board........................................................................................................ 27
2.1.10 LCD Rear Cover ................................................................................................. 28
2.1.11 I/O Cover ............................................................................................................. 28
2.1.12 MSR Module Base+ Power Button ................................................................... 28
2.1.13 MSR Reader Module Cover .............................................................................. 29
2.1.14 52 I/O Board........................................................................................................ 29
2.1.15 Battery Module.................................................................................................... 29
2.1.16 Handheld Belt ..................................................................................................... 30
2.2
Cables ............................................................................................................................. 30
2.2.1
Cable, M/B to Inverter ........................................................................................ 30
2.2.2
Cable, M/B To LCD............................................................................................. 31
2.2.3
Cable, M/B To LED............................................................................................. 32
2.2.4
Cable, M/B To I/O Connector ............................................................................ 33
2.3
Accessories .................................................................................................................... 34
2.3.1
MSR ..................................................................................................................... 34
2.3.2
Smart Card.......................................................................................................... 37
2.3.3
Barcode Scanner................................................................................................ 41
2.3.4
WLAN IEEE ........................................................................................................ 44
2.3.5
WLAN Bluetooth ................................................................................................. 45
2.3.6
Compact Flash.................................................................................................... 45
2.3.7
Memory................................................................................................................ 45
Chapter 3 Spare Parts ...................................................................................................................... 46
3.1
Main Unit......................................................................................................................... 47
3/30/2007
3/55
Rev. 1.1
EBN Technology Corp.
3.1.1
3.1.2
3.2
Battery Module ............................................................................................................... 49
3.2.1
Explode of Battery Module ................................................................................ 49
3.2.2
3.3
3/30/2007
Battery Module Parts List & Quotation ............................................................. 49
Recharge Cradle ............................................................................................................ 50
3.3.1
Explode of Recharge Cradle ............................................................................. 50
3.3.2
3.4
Explode of Main Unit .......................................................................................... 47
Main Unit Parts List & Quotation....................................................................... 47
Recharge Cradle Part List & Quotation............................................................ 50
Accessories .................................................................................................................... 54
3.4.1
3.4.2
Power Cord ......................................................................................................... 54
Memory................................................................................................................ 54
3.4.3
3.4.4
3.4.5
3.4.6
3.4.7
3.4.8
Compact Flash.................................................................................................... 55
MSR ..................................................................................................................... 55
Smart Card.......................................................................................................... 55
Barcode Scanner................................................................................................ 55
OS........................................................................................................................ 55
Wireless LAN ...................................................................................................... 55
4/55
Rev. 1.1
EBN Technology Corp.
Chapter 1
CHAPTER
1
Troubleshooting
3/30/2007
5/55
Rev. 1.1
EBN Technology Corp.
Chapter 1
Troubleshooting
1.1 Symptoms and Solutions
Error Code
Symptom
Check Points
Detail Steps
1. Check LED Light (Upper Left) should be on
2. If yes to item 1, check if Battery is well plugged on the
battery module
3. If yes to item 2, replace with another Battery for testing
4. If still fail, remove battery module/ remove MSR
1. Battery
3200
module base/ I/O Cover, open rear cover, open EMI
NO BOOT with 2. RAM
Power On
chassis, remove inverter cable on M/B (CN1), check if
3.MB
RAM well plugged on the memory slot
5. Check golden finger cleanness, if not clean, use pencil
eraser to clean golden finger
6. If fail, replace with another RAM for testing
7. If fail, replace with another mother board for testing
8. If fail, RMA system to EBN
1. Check if main unit is well plugged or not( The LED at
right hand side will show orange/ green color if it is
plugged correctly)
2. If the LED is on, check if Battery is well plugged on the
battery module
3100
NO POWER
1. Recharge cradle
3. If yes to item 2, push the power button to see if the LED
2. Battery
light is on(Upper left)
3. Power button cable
4. If the LED light is not on, check if power button cable is
4. 52 I/O board
well plugged or not
5. M/B to I/O connector 5. If yes to item 4, replace with another power button cable
cable
6. If fail, check if 52 I/O board is well plugged or not
6. MB
7. If yes to item 6, replace with another 52 I/O board
8. If still fail, check if M/B to I/O cable if well plugged or
not( MB CN32 and CN13)
9. If yes to item 8, replace with another I/O cable
10. If fail, replace with another mother board for testing
11. If still fail, RMA system to EBN
3/30/2007
6/55
Rev. 1.1
EBN Technology Corp.
Error Code
Symptom
Check Points
Detail Steps
1. Shut Down Power, remove battery module/ remove
MSR module base/ I/O Cover, open rear cover, check if
CF is well plugged or not
2. If yes to item 1, open EMI chassis, remove inverter
3201
System HANG
Up
1. CF
cable on M/B (CN1), check if check if RAM well plugged on
2. RAM
the memory slot
3. MB
2. Check golden finger cleanness, if not clean, use pencil
eraser to clean golden finger
3. If fail, replace with another RAM for testing
4. If fail, replace with another MB for testing
5. If fail, System RMA to EBN
1. Shut Down Power, remove battery module/ remove
MSR module base/ I/O Cover, open rear cover, open
inverter cover, replace with another inverter for testing
1. Inverter
3300
LCD Blank
2. If fail, check if LCD signal cable well connected on
2. MB
MB(CN2)
3. M/B to LCD cable
3. If yes to item 2, replace with another MB for testing
4. If fail, replace with another LCD signal cable for testing
5. If fail, System RMA to EBN
1. Shut Down Power, remove battery module/ remove
MSR module base/ I/O Cover, open rear cover, open
inverter cover, check if inverter to LCD cable is well
plugged or not.
2. If yes to item 1, replace with another inverter for testing
1. Inverter
2. If fail, is, remove EMI cover, check if inverter cable well
2. Inverter Cable
3301
connected between MB(CN1) and inverter
LCD Turn Black 3. MB
3. If yes, replace with another inverter cable for testing
4. M/B to LCD cable
4. If fail, check if LCD signal cable well connected on
5.LCD
MB(CN2)
5. If yes, replace with another MB for testing
6. If fail, replace with another LCD signal cable for testing
8. If fail, replace another LCD for testing
9. If fail, System RMA to EBN
3/30/2007
7/55
Rev. 1.1
EBN Technology Corp.
Error Code
Symptom
Check Points
Detail Steps
1. Shut Down Power, remove battery module/ remove
MSR module base/ I/O Cover, open rear cover, open EMI
chassis, remove inverter cable on M/B (CN1),
3. Check if CF Card well connected with CF Slot
3601
Unable to
1. CF Card
4. If yes to item 3, remove CF card, check if pins on CF
detect CF /
2. CF Slot
slot located at the correct position
Unstable CF
3. MB
5. If CF slot is damaged, go to item 7; if CF slot is not
damaged go to item 6
6. If yes to item 4, replace with another CF card for testing
7. If fail, replace with MB for testing
8 If fail, system RMA to EBN
1. Shut Down Power, remove battery module/ remove
MSR module base/ I/O Cover, open rear cover, open EMI
3602
chassis, remove inverter cable on M/B (CN1), check if CF
Data Can’t read 1. CF
and write
Card well connected with CF Slot
2. MB
2. If yes to item 2, replace with another CF card for testing
3. If fail, replace with MB for testing
4 If fail, system RMA to EBN
1. Shut Down Power, remove battery module/ remove
3500
CMOS
checksum error
MSR module base/ I/O Cover, open rear cover, open EMI
1. MB
chassis, remove inverter cable on M/B (CN1), replace with
another MB for testing
2. If fail, system RMA to EBN
1. Reinstall touch driver
2. If fail, shut down power, remove battery module/ remove
3400
1. Driver (NA)
MSR module base/ I/O Cover, open rear cover, open EMI
Touch
2. Touch to.MB cable
chassis, remove inverter cable on M/B (CN1), check if
malfunction
3. MB
touch panel cable well connected with MB
4. Touch panel
3. If yes to item 2, replace with another MB for testing
4. If fail, replace with another touch panel for testing
5. If fail, RMA system to EBN
3/30/2007
8/55
Rev. 1.1
EBN Technology Corp.
Error Code
Symptom
Check Points
Detail Steps
1. Check if USB keyboard cable well connected with USB
port
2. If yes to item 2, replace with another keyboard(same
model) for testing
Boot Up, USB
3700
K/B
Malfunction
3. If fail, replace with another keyboard(other model)
1. USB Keyboard
for
testing
3. MB
4. If fail, shut down power, remove battery module/ remove
MSR module base/ I/O Cover, open rear cover, open EMI
chassis, remove inverter cable on M/B (CN1), replace with
another MB for testing.
7. If fail, system RMA to EBN
1. Shut down power, remove battery module, check if MSR
1. MSR to 52 I/O board
3701
MSR
Cable
Malfunction
2. MSR
cable well connected with 52 I/O Board
2. If yes to item 2, replace with another MSR for testing
3. If fail, open rear cover, open EMI chassis, remove
inverter cable on M/B (CN1), replace with another MB for
3. MB
testing
4. If fail, RMA MSR to EBN
1. Check if USB keyboard cable well connected with USB
port
2. If yes to item 2, replace with another keyboard(same
model) for testing
3703
USB Device
1. Device USB cable
Malfunction
3. MB
3. If fail, replace with another keyboard(other model)
for
testing
4. If fail, shut down power, remove battery module/ remove
MSR module base/ I/O Cover, open rear cover, open EMI
chassis, remove inverter cable on M/B (CN1), replace with
another MB for testing.
7. If fail, system RMA to EBN
3/30/2007
9/55
Rev. 1.1
EBN Technology Corp.
1.2 BIOS Upgrade
1.2.1
Equipment List:
-USB Floppy Disk* 1 set
-Keyboard* 1 set,
-1.44MB Floppy Boot up Disk*1
-BIOS file
1.2.2
Upgrade Process
Make a start up disk and copy BIOS and EXE file
Item
Photo
Description
1
1.
Put empty 1.44MB disk into
USB floppy disk
2.
Plug the disk into another
computer with XP OS
installed
Click “My Computer”. The
new device “Floppy A” will
show on the screen
3.
2
1. Right click floppy disk and
select “Format”
3
1.
2.
3/30/2007
10/55
Click “Create an MS-DOS
startup disk”
Click “Start”
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
4
1. Click “OK”
5
1. Click “OK”.
2. The start up disk is created
6
1. Check the files in floppy disk
2. Leave 3 files in the floppy disk,
delete the rest files
highlighted.
7
1. Only 3 files left in the floppy
disk
-“COMMAND.COM”
-“IO SYS” (hidden file)
-“MSD OS.SYS”(hidden file)
2. Copy BIOS file and EXE. File
into floppy disk
3/30/2007
11/55
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
8
1. Plug the floppy disk into
Mobile POS
2. Power on the computer
3. Ensure that 3 files show on
the screen
-Commend COM
-AWDFLASH EXE
-BIOS file(Ex: B010R~1 Bin)
Update BIOS file
Item
Photo
Description
1
4. Reboot Mobile POS 50
5. Press “Del” button
6. Choose “Advanced BIOS
Features”
7. Press “Enter” Key
2
1. Choose “First Boot Device”.
2. Press “Enter” Key
3
1.
2.
3.
4.
file
3/30/2007
12/55
Select “USB-FDD”.
Press “Enter” Key
Press “F10”.
Press “Enter” key to save the
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
4
1. Key in BIOS Utility and BIOS
Version needs to be updated. Ex:
“awdflash b010wr10.bin”
awdflash = BIOS FLASH
B010wr10.bin =BIOS file
5
1. Press “N”.
6
1. Press “Y”. Press “Enter” Key
7
Note: DO NOT TURN OFF or
RESET SYSTEM Until the BIOS
update is completed. Stopping
the BIOS update before it is
completed will cause the system
to become non-functional.
3/30/2007
13/55
Press “Enter” Key
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
1. Wait till the screen shows
“Flashing Complete”.
8
2. Press “F1” to reset
9
3/30/2007
1. Double check the BIOS
version is updated when the
system resets.
Note:
The BIOS contained here is
exclusively for EBN MPOS 50
Series only. EBN has no
responsibility for any damages
resulting from improper use or
lacking of technical expertise at
field side
14/55
Rev. 1.1
EBN Technology Corp.
Chapter 2
CHAPTER
2
Disassembly, Assembly
3/30/2007
15/55
Rev. 1.1
EBN Technology Corp.
Chapter 2
Disassembly, Assembly
2.1 Main Unit
2.1.1 Touch Panel + Touch Screen Holder
Item
Photo
Description
1
1. Unpack handheld belt
2
1. Remove 2 screw pad
2. Remove 2 screws from I/O
cover
3
1. Move the clicker to right and
push up
4
1. Remove battery from battery
module
3/30/2007
16/55
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
5
6
1. Remove 4 screws from MSR
reader module cover
1
1. Remove MSR reader module
cover
2. Remove handheld belt
2
7
1. Remove I/O cover
8
1. Remove power button cable
2. Remove 4 screws from I/O
board
3. Remove MSR cable if needed
2
1
3
3/30/2007
17/55
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
1. Remove I/O board from MSR
9
module base
10
1. Remove 4 screws from MSR
module base
11
1. Remove MSR module base
12
1. Remove 4 screws from LCD
rear cover
2. Be aware of different screw
length. The misplace of the
screw will cause the LCD
broken
3/30/2007
18/55
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
1. Push out the LCD rear cover
13
1
to loose clicker
2. Push down the LCD rear
cover to enable COM port go
underneath the cover
3. Push up the LCD rear cover to
loose clicker
2
3
14
1. Remove 2 hex nuts from COM
port
2. Remove cable (inverter to
LCD)
2
1
15
1. Remove 4 screws from EMI
cover
2. Remove cable( inverter to
M/B)
2
1
3/30/2007
19/55
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
16
1. Push up the EMI cover
17
1. Remove touch panel cable
2. Pull up the black tape
1
2
18
1. Remove the LCD module / M/B
and EMI cover from touch panel
module
19
1. Replace with another touch
panel module
3/30/2007
20/55
Rev. 1.1
EBN Technology Corp.
2.1.2 LCD, AUO 8.4”
Item
Photo
1
3
Description
1. Follow 2.1.1 item 1 to 16
4
2. Remove cable (touch panel to
M/B )(CN29) and pull up the
2
black tape
3. Pull out LED cable from LED
CN2
CN6
frames
4. Remove cables (LCD to M/B)
(CN2) and (LED to M/B)(CN6)
2
1. Remove 4 screws from M/B
3
1. Remove M/B and EMI chassis
3/30/2007
21/55
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
1. Remove 2 heat pads
4
2. Remove mylar from M/B
1
2
5
1. Turn
to front side. Remove 4
screws from LCD chassis
6
1.
Remove LCD cable
2. Replace with another LCD
2.1.3 LCD Chassis
Item
Photo
Description
1
Follow 2.1.2 item 1 to 4
2. Remove 4 screws on LCD
3. Pull out 3 LED frames from
LCD chassis
1.
3
2
3/30/2007
22/55
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
1. Replace with another LCD
2
chassis
2.1.4 M/B
Item
Photo
Description
4
1
1. Follow 2.1.1 item 1 to 16
2. Remove fan cable(CN11) and switch
3
cable(CN13)
5
3. Remove touch panel cable(CN29)
CN2
and pull up the black tape
CN6
CN29
4. Remove cable (inverter to M/B)(CN1)
5. Remove LCD cable(CN2) and LED
2 CN11
cable (CN6)
CN13
6. Remove USB cable *2 and audio
cable(CN17)
7. Remove COM 3 cable
8. Remove COM2 cable(CN27)
9. Remove power cable(CN32)
6
9
7
CN17
CN32
CN27
3/30/2007
8
23/55
Rev. 1.1
EBN Technology Corp.
Item
Photo
2
Description
1. Remove 4 screws
2. Remove RAM from M/B(CN9)
1
3. Remove CF from M/B(CN8)
4. Replace with another M/B
3
2
2.1.5 EMI A/D Cover
Item
Photo
Description
1
1.
2.
3.
4.
3
4
Follow 2.1.1 item 1 to 14
Remove 4 screws
Remove inverter cable
Remove 8 screws from
speaker
2
2
1
2
3
1. Remove 2 screws from
inverter cover
2. Remove inverter cover
1. Remove I/O cable from I/O
board
2. Pull out 2 speakers
1
2
3/30/2007
24/55
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
4
1. Remove 2 screws from I/O
board
3
2. Remove I/O board from EMI
cover
2
3. Replace with another EMI
cover
2.1.6 Speaker Module
Item
1
Photo
Description
1. Follow 2.1.1 item 1 to 14
2. Remove inverter cable
3. Remove 8 screws from
speaker
4. Remove 4 screws
5. Open EMI cover
2
3
4
2
1. Remove audio cable(CN17)
from M/B
3
1. Replace with another speaker
module
Note: The white cable goes to left
hand side, while red cable goes to
right hand side
3/30/2007
25/55
Rev. 1.1
EBN Technology Corp.
2.1.7 Inverter
Item
1
Photo
Description
1. Follow item 2.1.1 item 1 to 14
2
2. Remove inverter cable
3. Remove 1 screw from inverter
cover
3
2
1
2
1. Remove 2 screws from
inverter cover
3
1. Remove 2 screws from
inverter
4
1. Replace with another inverter
3/30/2007
26/55
Rev. 1.1
EBN Technology Corp.
2.1.8 Inverter Cover
Item
Photo
Description
1
1. Follow item 2.1.7 item 1 to 3
2. Replace with another inverter
cover
2.1.9 51 I/O Board
Item
1
Photo
Description
1.
2.
3.
4.
2
Follow 2.1.1 item 1 to 14
Remove inverter cable
Remove 4 screws
Open EMI cover
3
2
1. Remove I/O cable from EMI
cover
3
1. Turn the EMI cover to the
other side
2. Remove 2 screws from 51 I/O
board
3. Replace with another 51 I/O
board
3/30/2007
27/55
Rev. 1.1
EBN Technology Corp.
2.1.10
LCD Rear Cover
Item
Photo
Description
1
1. Follow 2.1.1 item 1 to 13
2. Replace with another LCD
rear cover
2.1.11
Item
I/O Cover
Photo
Description
1
1. Follow 2.1.1 item 1 to 6
2. Replace with another I/O
Cover
2.1.12
Item
MSR Module Base+ Power Button
Photo
Description
1
3/30/2007
1. Follow 2.1.1 item 1 to 10
2. Replace with another MSR
module
28/55
Rev. 1.1
EBN Technology Corp.
2.1.13
Item
1
MSR Reader Module Cover
Photo
Description
1. Follow 2.1.1 item 1 to 5
1
2. Remove MSR reader module
cover
2
1. Replace with another MSR
reader module cover
2.1.14
Item
52 I/O Board
Photo
Description
1
2. Follow 2.1.1 item 1 to 8
3. Replace with another 52 I/O
Board
2.1.15
Item
Battery Module
Photo
Description
1
3/30/2007
1. Follow 2.1.1 item 1 to 3
2. Replace with another Battery
module
29/55
Rev. 1.1
EBN Technology Corp.
2.1.16
Item
Handheld Belt
Photo
Description
1
1. Unpack handheld belt
2
1. Remove 4 screws from MSR
reader module cover
3
1. Replace with another
handheld belt
2.2 Cables
2.2.1 Cable, M/B to Inverter
Item
Photo
Description
1
3/30/2007
1. Follow 2.1.1 item 1 to 15
2. Push up the EMI cover
30/55
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
2
1. Remove inverter to M/B
cable(CN1)
3
1.
Replace with another inverter
cable
2.2.2 Cable, M/B To LCD
Item
Photo
Description
1
1. Follow 2.1.2 item 1 to 6
2. Remove LCD cable
1
1. Replace with another LCD
cable
3/30/2007
31/55
Rev. 1.1
EBN Technology Corp.
2.2.3 Cable, M/B To LED
Item
Photo
1
Description
1. Follow 2.1.1 item 1 to 16
3
2
2. Pull out the 2 LED from LED
frames
3. Cut plastic belt (Green at the
4
left / white in the middle)
4. Remove LED cable (CN6)
2
3/30/2007
1. Replace with another LED
cable
32/55
Rev. 1.1
EBN Technology Corp.
2.2.4 Cable, M/B To I/O Connector
Item
Photo
Description
1
1. Follow 2.1.1 item 1 to 16
2. Remove fan cable(CN11) and switch
3
cable(CN13)
5
3. Remove touch panel cable(CN29) and
CN2
pull up the black tape
CN6
CN29
4. Remove inverter cable(CN1)
5. Remove LCD cable (CN2) and LED
2 CN11
cable (CN6)
CN13
6. Remove USB cable *2 and audio
cable(CN17)
7. Remove COM 3 cable
8. Remove COM2 cable(CN27)
9. Remove power cable(CN32)
6
9
7
CN17
CN32
CN27
8
1. Remove the I/O connector
cable
2
3/30/2007
33/55
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
1. Replace with another I/O
Connector cable
3
2.3 Accessories
2.3.1 MSR
HW Installation
Item
Photo
Description
1
1. Take out MSR module
2
1. Follow 2.1.1 item 1 to 5
2. Put MSR module at upper
position
3. Fasten 2 screws to tighten
MSR module
4. Plug MSR cable to I/O board
5. Follow steps back to 2.1.1
item 1
2
3
Verification: RS232 type
Item No.
Photo
Description
1. Enter to “All Programs” “Communication” “Hyper Terminal”
1
3/30/2007
34/55
Rev. 1.1
EBN Technology Corp.
Item No.
Photo
Description
1. Click “Yes” to continue
2
1. Set “area code” and click OK
3
1. Click OK
4
1. Enter a name and Click OK
5
3/30/2007
35/55
Rev. 1.1
EBN Technology Corp.
Item No.
Photo
Description
1. Select on using COM2 port for MSR
(Select COM3 if scanner installed)
2. Click “OK”
6
1. Set Bits per second to be 9600 bps.
7
1. Test OK
8
3/30/2007
36/55
Rev. 1.1
EBN Technology Corp.
2.3.2 Smart Card
HW Installation
Item
Photo
Description
1
2
1. Take out smart card module
1
2
3
1. Put smart card in the reader
module
2. Fasten 2 screws to tighten
smart card
2
4
3/30/2007
1. Follow 2.1.1 item 1 to 5
2. Remove MSR reader module
cover
3. Turn MSR reader module cover
to the other side
1. Plug smart card cable on I/O
board
2. Follow steps back to 2.1.1 item
1
37/55
Rev. 1.1
EBN Technology Corp.
Verification
Item
Photo
Description
1
1. Click “start””Setting””Control
Panel””System”
2
1. Click “Hardware”
2. Click “Device Manager”
3
1. Click “”Detect plug in device..”
2. Double click “USB Device”
4
1. Click “Update Driver”
3/30/2007
38/55
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
5
1. Click “Yes, this time only”
2. Click “Next”
6
1. Click “Install from a list or
specific location…”
2. Click “Next”
7
1. Click “Browse”
8
1. Choose the location where the
driver is stored
2. Click “OK”
3/30/2007
39/55
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
9
1. Click “Next”
10
1. Click “Finish” and the installation
process is completed
11
1. Click “Shortcut to
SYN_PcSc_Test”
12
1. Click “STD2000”
3/30/2007
40/55
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
13
1. Insert any smart card into smart
card reader
14
1. The test result “PASS” will show
on the screen
2. The installation is completed
2.3.3 Barcode Scanner
Item
Photo
Description
1
2
3/30/2007
1. Take out smart card module
2
3
41/55
1. Follow 2.1.1 item 1 to 5
2. Remove MSR reader module
cover
3. Remove handheld belt
Rev. 1.1
EBN Technology Corp.
Item
Photo
Description
1. Put barcode scanner module on
3
MSR module base
2. Fasten 2 screws to tighten
2
barcode scanner
3. Turn Mobile POS 90° to the left
3
4
1. Put the cable into the connector
on I/O board
5
1. Push in the cable
2. Lock the cable by pushing in
black clicker
3. Follow steps back to 2.1.1 item
1
2
1
Verification:
Item No.
Photo
Description
1. Enter to “All Programs” “Communication” “Hyper Terminal”
1
3/30/2007
42/55
Rev. 1.1
EBN Technology Corp.
Item No.
Photo
Description
1. Click “Yes” to continue
2
1. Set “area code” and click OK
3
1. Click OK
4
1. Enter a name and Click OK
5
3/30/2007
43/55
Rev. 1.1
EBN Technology Corp.
Item No.
Photo
Description
3. Select on using COM3 port for
barcode scanner (Select COM2 if
MSR installed)
4. Click “OK”
6
1. Set Bits per second to be 9600 bps.
7
1. Test OK
8
2.3.4 WLAN IEEE
Item
Photo
1
Description
1. Follow 2.1.1 item 1 to 11
2. Use adhesive tape to stick
WLAN IEEE with rear cover
3. Plug in the WLAN IEEE cable to
USB port
4. Follow steps back to 2.1.1 item
1
5. Follow the steps in driver CD for
installation process
3
2
3/30/2007
44/55
Rev. 1.1
EBN Technology Corp.
2.3.5 WLAN Bluetooth
Item
Photo
1
Description
1. Follow 2.1.1 item 1 to 11
3
2. Use adhesive tape to stick blue
tooth with rear cover
2
3. Plug in the WLAN IEEE cable to
USB port
4. Follow steps back to 2.1.1 item
1
1. Follow the steps in driver CD for
installation process
2.3.6 Compact Flash
Item
Photo
Description
1
1. Follow 2.1.1 item 1 to 16
2. Put CF in the CF slot
3. Follow steps back to 2.1.1 item
1
3
2.3.7 Memory
Item
Photo
Description
1
1. Follow 2.1.1 item 1 to 16
2. Put RAM in the RAM slot
3. Follow steps back to 2.1.1 item
1
2
3/30/2007
45/55
Rev. 1.1
EBN Technology Corp.
CHAPTER
3
Chapter 3
Spare Parts
3/30/2007
46/55
Rev. 1.1
EBN Technology Corp.
Chapter 3
Spare Parts
3.1 Main Unit
3.1.1 Explode of Main Unit
3.1.2 Main Unit Parts List & Quotation
Item
1+2
Part No.
A10400237RH
Description
Q’ty
Plastic Bezel: 8.4"LCD W/ Water proof
sealed stick
1
Touch Panel: 8.4", Resistive,
HT-084F-5RA-002N-18
1
Price (USD)
Call Sales
3
21100011RH
AUO 8.4" LCD PANEL
1
Call Sales
4
30100061RH
LCD chassis (AL=1.0mm)
1
Call Sales
5
10100047RH
LX-800 M/B
1
Call Sales
3/30/2007
47/55
Rev. 1.1
EBN Technology Corp.
Item
Part No.
Description
Q’ty
Price (USD)
7+8+
9+10
A10400561RH
EMI Chassis Module
1
Call Sales
12
30200061BRH
Cover: 8.4 LCD rear cover, Black
1
Call Sales
13
30200051BRH
Cover: I/O Cover, Black
1
Call Sales
+11
3/30/2007
48/55
Rev. 1.1
EBN Technology Corp.
3.2 Battery Module
3.2.1 Explode of Battery Module
3.2.2 Battery Module Parts List & Quotation
Item
Part No.
1+16
30200058BRH
+21600116RH
Plastic Base: Reader Module Base,
PC+ABS, Black
1
Call Sales
5
10100039RH
52 I/O Board
1
Call Sales
10
30200057BRH
+30500026RH
Cover: Reader Module Cover, Black W/
Len LED
1
Call Sales
11
30200059BRH
Cover: Scanner Cover, Black
1
Call Sales
12
30200060BRH
Cover: Smart Card Cover, Black
1
Call Sales
15
A10400199RH
Battery Module: 11.1V, 2400mA, Li-ion
3P1S SONY Cell, 68 x 55 x 23.5(mm)
1
Call Sales
3/30/2007
Description
49/55
Q’ty
Price (USD)
Rev. 1.1
EBN Technology Corp.
3.3 Recharge Cradle
3.3.1 Explode of Recharge Cradle
3.3.2 Recharge Cradle Part List & Quotation
Item
Part No.
1+2+
3+5+
6
A10400116RH
3/30/2007
Description
Recharge Cradle Module
50/55
Q’ty
1
Price (USD)
Call Sales
Rev. 1.1
EBN Technology Corp.
Part No.
21600094RH
Description
Photo
Inverter cable
Price(USD)
Call Sales
I/O CONNECTOR cable,
P=2.0 44Pin , MOLEX
21600103RH
21600095RH
P=1.25 4Pin+MOLEX
P=1.25 4Pin+MOLEX
P=1.25 15Pin+MOLEX
P=1.25
LCD CABLE for AUO panel
21600041RH
LED cable
31400003RH
Heat pad 40*40*2(mm)
3/30/2007
Call Sales
Call Sales
Call Sales
Call Sales
51/55
Rev. 1.1
EBN Technology Corp.
Part No.
31400004RH
Description
Photo
Heat pad 23*23*2(mm)
Price(USD)
Call Sales
31700001RH
+31700002R
H
Hand Held Belt
Call Sales
40200016RH
Carton: Inner Packing
Carton 321 *228 *585 (mm)
Call Sales
40200024RH
Carton: Outer Packing
Carton 700*310*210(mm)
Call Sales
3/30/2007
52/55
Rev. 1.1
EBN Technology Corp.
Part No.
Description
Photo
Price(USD)
EPE Sponge for Mobile
40800014RH
40800023RH
31800001RH
+31800002R
H
3/30/2007
POS Main Unit(Left and
Call Sales
Right)
EPE Sponge for Mobile
POS Recharge Cradle(Left
and Right)
Leather Bag: Bag w/ Belt
Call Sales
Call Sales
53/55
Rev. 1.1
EBN Technology Corp.
3.4 Accessories
3.4.1 Power Cord
Part No.
Description
Photos
Price(USD)
POWER CORE FOR USA
Call Sales
20700001RH
POWER CORD FOR UK
Call Sales
20700005RH
POWER CORD FOR EUR
Call Sales
20700002RH
POWER CORD FOR Australia
Call Sales
20700004RH
3.4.2 Memory
Part No.
Description
Photo
Price(USD)
20300005RH
400MHz DDR MODULE
128M(200PIN-SO DIMM)
Call Sales
20300006RH
400MHz DDR MODULE
256M(200PIN-SO DIMM)
Call Sales
20300007RH
400MHz DDR MODULE
512M(200PIN-SO DIMM)(
Call Sales
3/30/2007
54/55
Rev. 1.1
EBN Technology Corp.
3.4.3 Compact Flash
Photo
Price(USD)
Part NO.
Description
20600001RH
Compact Flash 128MB
Call Sales
20600002RH
Compact Flash 256MB
Call Sales
20600003RH
Compact Flash 512MB
Call Sales
20600005RH
Compact Flash 1G
Call Sales
20600007RH
Compact Flash 2G
Call Sales
3.4.4 MSR
Part NO.
Description
20400008RH
MSR 3 Tracks, RS232
Photo
Price(USD)
Call Sales
3.4.5 Smart Card
PART NO.
Description
Price(USD)
A10400198RH Smart Card Module for Mobile POS
Call Sales
3.4.6 Barcode Scanner
PART NO.
Description
Price(USD)
A10400197RH Barcode Scanner Module: Laser Engine W/
RS-232+130mm FPC CABLE
Call Sales
3.4.7 OS
PART NO.
Description
Price(USD)
20900001RH
WinXP Professional, English Version
Call Sales
20900002RH
WEPOS, English Ver.
Call Sales
3.4.8 Wireless LAN
PART NO.
Description
60900002RH
WiFi
WLAN:WiFi
802.11b/g USB
61000001RH
Bluetooth
V1.2
DONGLE(BT-01UD1)
3/30/2007
Photo
WLAN
USB
55/55
Price(USD)
Call Sales
Call Sales
Rev. 1.1

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement