advertisement
Leica DISTO
TM
D510
The original laser distance meter
The original laser distance meter
Table of Contents
Instrument Set-up
- - - - - - - - - - - - - - - - - - - - - - - - - - 2
Introduction - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2
Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2
Basic measuring screen - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3
Selection screen- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3
Pointfinder (Viewscreen)- - - - - - - - - - - - - - - - - - - - - - - - - - - 4
Insert batteries - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4
Operations
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5
Switching ON/OFF - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5
Clear - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5
Message Codes - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5
Multifunctional endpiece - - - - - - - - - - - - - - - - - - - - - - - - - - - 5
Permament / Minimum-Maximum measuring- - - - - - - - - - - - - 5
Add / Subtract - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
Pointfinder (Viewscreen)- - - - - - - - - - - - - - - - - - - - - - - - - - - 6
Settings
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7
Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7
Tilt units - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7
Distance units - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8
Beep ON/OFF - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8
Digital level ON/OFF - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8
De-/Activate keylock - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9
Switch on with keylock - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9
Smart - - - - - - - - - - - - - - - - - - - - - - 9
Calibration of tilt sensor (Tilt Calibration) - - - - - - - - - - - - - - 10
Personalized favorites - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11
Illumination - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11
Offset- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12
Reset - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12
Functions
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 13
Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 13
Timer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 13
Calculator - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 13
Adjusting measuring reference/tripod - - - - - - - - - - - - - - - - - 14
Leica DISTO TM D510 792312c
EN
Memory- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 15
Measuring single distance - - - - - - - - - - - - - - - - - - - - - - - - - - 15
Smart Horizontal Mode - - - - - - - - - - - - - - - - - - - - - - - - - - - 15
Inclination tracking- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 16
Area - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 16
Volume - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 17
Triangular area - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 18
Long range mode - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 18
Height-profile measurement - - - - - - - - - - - - - - - - - - - - - - - - 19
Sloped objects - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 20
Height tracking - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 21
Trapezium - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 22
Stake out - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 23
Pythagoras (2-point) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 24
Pythagoras (3-point) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 25
Technical Data
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 26
Message Codes
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 27
Care
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 27
Warranty
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 27
Safety Instructions
- - - - - - - - - - - - - - - - - - - - - - - - - 27
Areas of responsibility - - - - - - - - - - - - - - - - - - - - - - - - - - - - 27
Permitted use - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 28
Prohibited use - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 28
Hazards in use - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 28
Limits of use - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 28
Disposal- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 28
Electromagnetic Compatibility (EMC) - - - - - - - - - - - - - - - - - 29
Use of the product with Bluetooth® - - - - - - - - - - - - - - - - - - 29
Laser classification - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 29
Labelling - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 29
1
Instrument Set-up
Introduction
The safety instructions and the user manual should be read through carefully before the product is used for the first time.
The person responsible for the product must ensure that all users understand these directions and adhere to them.
The symbols used have the following meanings:
WARNING
Indicates a potentially hazardous situation or an unintended use which, if not avoided, will result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation or an unintended use which, if not avoided, may result in minor injury and/or appreciable material, financial and environmental damage.
i
Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner.
Overview
Display
On/Measure
Pointfinder
(Viewscreen)
Navigation
Clear / Off
Leica DISTO TM D510 792312c
EN
Selection keys linked to symbols above
Function screen
Return /
Equal
Add /
Subtract
2
Instrument Set-up
Basic measuring screen
Status bar
Main line
Active function
Favorites
Leica DISTO TM D510 792312c
Selection screen
Page indicator
FUNC
Function /
Settings
Settings Help function
EN
3
Instrument Set-up
Pointfinder (Viewscreen)
Zoom stage
1x
Illumination adjustment with navigation keys left and right
Active function
Favorites
Crosshair
Zoom (1x, 2x, 4x) with navigation keys up and down
Insert batteries
EN i
To ensure a reliable use, do not use zinccarbon batteries.
We recommend using high quality batteries.
Change batteries when battery symbol is flashing.
Leica DISTO TM D510 792312c
4
Operations
Switching ON/OFF
ON OFF
2 sec
Device is turned
OFF.
i
If no key is pressed for 180 sec, the device switches off automatically.
Clear
1x
Undo last action.
2x
Leave actual function, go to default operation mode.
EN
Message Codes
If the info icon appears with a number, observe the instructions in section "Message Codes".
Example:
Multifunctional endpiece
i
The orientation of the endpiece is automatically detected and the zero point is accordingly adjusted.
Permament / Minimum-Maximum measuring
min.
max.
1 2
2 sec
Used to measure room diagonals (maximum values) or horizontal distance (minimum values)
Leica DISTO TM D510 792312c
The minimum and maximum distance measured is displayed (min, max.). The last value measured is displayed in the main line.
3
8.532 m
Stops permanent / minimummaximum measuring.
5
Operations
Add / Subtract
1
2x
7.332 m
2
The next measurement is added to the previous one.
The next measurement is sub-
tracted from the previous one.
3
Pointfinder (Viewscreen)
1x
1 2
4x
4x
2x
2x
1x
1x
7.332 m
12.847 m
4
3
20.179 m
EN i
This process can be repeated as required. The same process can be used for adding or subtracting areas or volumes.
1x
4
Exit pointfinder
(viewscreen).
i
This is a great help for outdoor measuring. The integrated pointfinder (viewscreen) shows the target on the display.
The device measures in the middle of the cross hair, even if the laser dot is not visible.
Parallax errors occur when the pointfinder camera is used on close targets, with the effect that the laser appears displaced in the crosshair. In this case rely on the real laser dot.
Leica DISTO TM D510 792312c
6
Settings
Overview
1 2
1
Tilt units
2 3
Tilt units
Distance units
Beep
Digital level
Keypad lock
Bluetooth
®
Tilt calibration
Favorites
Illumination
Offset
Reset
Information
Switch between the following units:
360.0°
± 180.0°
± 90.0°
0.00 %
0.0 mm/m
0.00 in/ft
4
Confirm setting.
5
Exit settings.
Leica DISTO TM D510 792312c
EN
7
Settings
Distance units
1 2 3
Switch between the following units:
0.00 m
0.000 m
0.0000 m
0.0 mm
0.00 ft
0.00 in
0 1/32 in
0'00" 1/32
4
Confirm setting.
5
Exit settings.
1
Beep ON/OFF
2 3
To switch ON, repeat procedure.
Exit settings.
1
ON
OFF
Digital level ON/OFF
2 3
To switch ON, repeat procedure.
Exit settings.
i
The digital level is displayed in the status bar.
ON
Leica DISTO TM D510 792312c
OFF
EN
8
1
Settings
De-/Activate keylock
2
To deactivate, repeat procedure. The keylock is active if device is switched off.
3
Exit settings.
Switch on with keylock
1 2
within
2 sec
EN
OFF ON
De-/Activate Bluetooth
®
Smart
1 2 3
i
Default mode:
Bluetooth
®
is switched on.
Bluetooth
®
icon in status line is displayed if device is connected with Bluetooth
®
.
To switch ON, repeat procedure.
Exit settings.
i
ON
OFF
Switch on Bluetooth ® Smart in Settings.
Connect the device with your smart phone, pad, laptop,…
The actual measurement is transferred automatically if Bluetooth
®
connection is established. To transfer a result from the main line, press =.
Bluetooth
®
switches off as soon as the laser distance meter is switched off.
The efficient and innovative Bluetooth
Bluetooth
®
®
Smart module (with the new
standard V4.0) works together with all Bluetooth
®
Smart
Ready devices. All other Bluetooth ® devices do not support the energy saving Bluetooth
®
Smart Module, which is integrated in the device.
We provide no warranty for free DISTO ™ software and offer no support for it. We accept no liability whatsoever arising from the use of the free software and we are not obliged to provide corrections nor to develop upgrades. A wide range of commercial software can be found on our homepage. Apps for Android
®
or Mac iOS can be found in special internet shops.
For more details, see our homepage.
Leica DISTO TM D510 792312c
9
1
Settings
Calibration of tilt sensor (Tilt Calibration)
2 3 4
EN
180°
Place device on absolutely flat surface.
180°
5 6 7
8
Turn the device horizontally by 180° and place it again on absolutely flat surface.
180°
9
180°
Turn the device horizontally by 180° and place it again on absolutely flat surface.
10
Place device on absolutely flat surface.
i
After 2 sec the device goes back to the basic mode.
Leica DISTO TM D510 792312c
10
1
Settings
Personalized favorites
Favorite
2
1
Illumination
2
1/6
3
EN
3
Select favorite function.
4
Press selection key left or right.
Function is set as favorite above the corresponding selection key.
5
Exit settings.
i
Select your favorite functions for quick access.
Short cut:
Press 2 sec on a selection-key in the measuring mode.
Select brightness.
4 5
Confirm setting.
Exit settings.
i
To save power reduce brightness if not necessary.
Leica DISTO TM D510 792312c
11
1
Settings
Offset
1 2 3
Select digit.
6
Exit settings.
i
An offset adds or subtracts a specified value automatically to or from all measurements. This function allows tolerances to be taken into account. The offset icon is displayed.
1.012 m
Reset
2
4
Adjust digit.
1.012 m
5
Approve value.
EN
3
Second confirmation with selection keys:
Refuse:
Confirm:
4
Exit settings.
i
Reset returns the instrument to the factory settings. All customized settings and memories are lost.
Leica DISTO TM D510 792312c
12
1
1
Functions
Overview
Timer
2
Timer
Calculator
Adjusting measuring reference
Memory
Single Distance Measurement
Smart Horizontal Mode
3
Inclination Tracking
Area
Volume
Triangle area
Long Range Mode
Height-profile Measurement
Measuring on sloped objects
Height Tracking
Trapezium
Stake out
Pythagoras 1
Pythagoras 2
30 sec
5 sec
2 sec
Off
Select release time.
4
Confirm setting.
i
The self release starts if
ON/Measure key is pressed.
EN
Calculator
2
Leica DISTO TM D510 792312c
3
C/CE
=
Select key on display.
i
The measurement result from the main line is taken over to the calculator and can be used for further calculations.
Ft/in fractions are converted into ft/in decimal.
Confirm every key.
Use selection keys for clear or result.
13
1
Functions
Adjusting measuring reference/tripod
2 3
Distance is measured from the rear of the device (standard setting).
Distance is measured from a Leica DISTO
Adapter FTA 360 (lock symbol = permanently)
Distance is measured from the tripod thread permanently.
Distance is measured from the front of the device (lock symbol = permanently).
4
Confirm setting.
i
If device is switched off, reference goes back to standard setting
(rear of the device).
If you use an original Leica DISTO adapter, the reference does not need to be adapted to tripod thread!
Leica DISTO TM D510 792312c
EN
14
1
Functions
Memory
2 3
1
Measuring single distance
2 3
12.208 m
6.554 m
23.889 m
Switch between measurements.
4
Delete memory.
Take over value for further actions.
Use Up/Down navigation keys to show more detailed results of the specific measurement.
i
Short cut
EN
Aim active laser at target.
4
8.532 m
i
Target surfaces:
Measuring errors can occur when measuring to colourless liquids, glass, styrofoam or semi-permeable surfaces or when aiming at high gloss surfaces. Against dark surfaces the measuring time increases.
1
Smart Horizontal Mode
2 3 4
Leica DISTO TM D510 792312c
Aim laser at target.
40.8 °
5.204 m
0.032 m
4.827 m
x y x z z
(up to 360° and a transverse tilt of ±10°)
15
1
Functions
Inclination tracking
2 3
89.3°
90°
0°
i
Inclination is permanently displayed.
Instrument beeps at 0° and 90°. Ideal for horizontal or vertical adjustments.
6
1
Area
2
6.228 m
3.9I0 m
20.276 m
24.352 m
2
3
Aim laser at first target point.
4
First distance
Second distance
Circumference
Area
5
Aim laser at second target point.
i
The result is shown in the main line and the measured value above.
Partial Measurements / Painter function:
Press + or - before starting the first measurement. Measure and add or subtract distances. Finish with =. Measure 2nd length.
EN
Leica DISTO TM D510 792312c
16
1
8
Functions
Volume
2 3
Aim laser at first target point.
4
5.744 m
2.338 m
2.431 m
32.653 m
3
First distance
Second distance
Third distance
Volume
9
EN
5 6 7
Aim laser at second target point.
Aim laser at third target point.
Use Up/Down navigation keys to show more results.
13.430 m
2
39.300 m
2
16.164 m
Ceiling/floor area
Wall areas
Circumference
Leica DISTO TM D510 792312c
17
1
Functions
Triangular area
2
EN
3
Aim laser at first target point.
4 5
Aim laser at second target point.
6 7
Aim laser at third target point.
8
1
4.248 m
4.129 m
2.425 m
4.855 m
2
First distance
Second distance
Third distance
Triangular area
Long range mode
2
9
i
The long range mode allows measuring of difficult targets in unfavorable conditions e.g. bright ambient light or bad target reflectivity. The measuring time is increased.
An icon in the status line shows if the function is active.
Use Up/Down navigation keys to show more results. Switch off
Pointfinder if activated.
33.60°
10.802 m
Angle between first and second measurement
Circumference
Leica DISTO TM D510 792312c
18
1
6
Functions
Height-profile measurement
EN
2 3
2.042 m
0.054 m
0
REF
Aim at reference point (REF).
2x d
Horizontal distance to device
7
Exit function.
h
Height difference to reference point (REF).
4
i
5
0
1
REF
Aim at additional points 1-x.
Ideal for measuring of height differences to a reference point. Can be also used to measure profiles and terrain sections. After measuring the reference point, the horizontal distance and height is displayed for each following point.
3
4
h
2
d
5
Leica DISTO TM D510 792312c
19
1
Functions
Sloped objects
2 3 4 5
EN i
6
P2 angle
11.00 °
30.367 m
-3.440 m
5.452 m
P2 distance
Vertical height between both points
Distance between both points
Indirect distance measuring between 2 points with additional results. Ideal for applications such as length and slope of roof, height of chimneys,…
It is important, that the instrument is positioned in the same vertical plane as the 2 measured points. The plane is defined of the line between the 2 points.
7
Aim laser at upper target point.
Use Up/Down navigation keys to show more results. Switch off
Pointfinder if activated.
Aim laser at lower target point.
39.10 °
-4.230 m
Included angle between both points
Horizontal distance between both points
Leica DISTO TM D510 792312c
20
1
6
8
Functions
Height tracking
EN
Px
Px
2 3 4 5
-10.55 °
6.271 m
29.89 °
3.475 m
Use Up/Down navigation keys to show more results. Switch off
Pointfinder if activated.
7.160 m
P0
Aim laser at lower point.
P0
= Tracking angle if device is turned on tripod
y
= Tracking height if device is turned on tripod
z
P0
Aim laser at upper points and angle/ height tracking starts automatically.
z
Px
7
Stops height tracking.
P0 i
Heights of buildings or trees without suitable reflective points can be determined. At the bottom point, distance and tilt is measured - which needs a reflective laser target. The upper point can be targeted with the pointfinder / crosshair and does not need a reflective laser target as only the inclination is measured.
-10.55 °
6.271 m
44.80 °
8.478 m
Leica DISTO TM D510 792312c
21
6
7
1
Functions
Trapezium
2 3
Aim laser at upper point.
x
13.459 m
16.440 m
70.80
°
5.790 m
x h
y
h y
Use Up/Down navigation keys to show more results. Switch off
Pointfinder if activated.
78.383 m 2
20.9
°
Trapezium area
4 5
Aim laser at 2nd point.
EN
Leica DISTO TM D510 792312c
22
i
Functions
Stake out
Two different distances (a and b) can be entered to mark off defined measured lengths.
a = b
3
3
Select digit.
7
Approve value "b" and start measurement.
8
1.012 m
b
2
1 b a a = b
3
2
1 b b a
5 4
Adjust digit.
1.012 m
Approve value "a".
Move device slowly along the stake-out line.
The distance to the next stake out point is displayed.
0.240 m is missing up to next 0.625 m distance.
Next stake out distance
0.625 m
0.240 m
1
6
Adjust value "b".
2
0.625 m
EN i
When approaching a stake out point to less than 0.1 m the instrument starts to beep.
The function can be stopped by pressing the CLEAR/OFF button.
Leica DISTO TM D510 792312c
23
1
Functions
Pythagoras (2-point)
2 3
6
25.133 m
21.383 m
13.207 m
EN
4 5
Aim laser at first target.
Aim laser at second target.
i
The result is shown in the main line.
Pressing the measuring key for 2 sec in the function activates automatically Minimum or Maximum measurement.
We recommend to use the pythagoras only for indirect horizontal measuring.
For height measuring (vertical) it is more precise to use a function with the inclination measuring.
Leica DISTO TM D510 792312c
24
8
1
Functions
Pythagoras (3-point)
2 3
Aim laser at first target.
4
24.298 m
21.264 m
23.018 m
20.571 m
EN
5 6 7
Aim laser at second target.
Aim laser at third target.
i
The result is shown in the main line.
Pressing the measuring key for 2 sec in the function activates automatically Minimum or Maximum measurement.
We recommend to use the pythagoras only for indirect horizontal measuring.
For height measuring (vertical) it is more precise to use a function with inclination measurement.
Leica DISTO TM D510 792312c
25
Technical Data
Distance measurement
Typical Measuring Tolerance* ± 1.0 mm / ~1/16" ***
Maximum Measuring
Tolerance**
± 2.0 mm / 0.08 in ***
Typical Range*
Range at unfavourable condition ****
200 m / 660 ft
80 m / 260 ft
Smallest unit displayed
Power Range Technology
™
Ø laser point at distances
0.1 mm / 1/32 in yes
6 /30 / 60 mm
(10 / 50 / 100 m)
Tilt measurement
Measuring tolerance to laser beam*****
Measuring tolerance to housing*****
Range
± 0.2°
± 0.2°
360°
General
Laser class
Laser type
Protection class
Autom. laser switch off
Autom. power switch-off
Bluetooth® Smart
Range of Bluetooth®
Bluetooth®
- Power
- Frequency
Battery durability (2 x AA)
Dimension (H x D x W)
2
635 nm, < 1 mW
IP65 (dust tight and jet water protected) after 90 s after 180 s
Bluetooth v4.0
10 m
0.6 mW
2402 - 2480 MHz up to 5000 measurements
143 x 58 x 29 mm
5.6 x 2.28 x 1.14 in
198 g / 6.37 oz
Weight (with batteries)
Temperature range:
- Storage
- Operation
-25 to 70 °C
-13 to 158 °F
-10 to 50 °C
14 to 122 °F
* applies for 100 % target reflectivity (white painted wall), low background illumination, 25 ºC
** applies for 10 to 100 % target reflectivity, high background illumination, - 10 ºC to + 50 ºC
*** Tolerances apply from 0.05 m to 10 m with a confidence level of 95%. The maximum tolerance may deteriorate to
0.1 mm/m between 10 m to 30 m, to 0.20 mm/m between
30 m to 100 m and to 0.30 mm/m for distances above 100 m
**** applies for 100 % target reflectivity, background illumination of approximately 30'000 lux
***** after user calibration. Additional angle related deviation of +/- 0.01° per degree up to +/-45° in each quadrant.
Applies at room temperature. For the whole operating temperature range the maximum deviation increases by
+/-0.1°.
i
For accurate indirect results, the use of a tripod is recommended. For accurate tilt measurements a transverse tilt should be avoided.
Functions
Distance measuring
Min/Max measuring
Permanent measuring
Stake-out
Addition/Subtraction
Area
Triangle area
Volume
Trapezium
Painter function (area with partial measurem.)
Pythagoras
Smart Horizontal Mode /
Indirect height
Height-profile measurement
Inclination tracking
Sloped objects
Height tracking
Memory
Beep
Illuminated colour display
Multifunctional endpiece
Pointfinder (Viewscreen)
Digital Level
Bluetooth
®
Smart
Personalized Favorites
Timer
Long Range Mode
Calculator
yes yes yes yes
30 displays yes yes yes
4xZoom yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes yes
2-point, 3-point yes
EN
Leica DISTO TM D510 792312c
26
Message Codes
If the message Error does not disappear after switching on the device repeatedly, contact the dealer.
If the message InFo appears with a number, press the Clear button and observe the following instructions:
No.
Cause
156 Transverse tilt greater than 10°
Correction
Hold the instrument without any transverse tilt.
162 Calibration mistake Make sure, the device is placed on a absolutely horizontal and flat surface.
Repeat the calibration procedure. If the mistake still occurs, contact your dealer.
204 Calculation error Perform measurement again.
240 Data transfer error Repeat procedure.
252 Temperature too high Let device cool down.
253 Temperature too low Warm device up.
255 Received signal too weak, measuring time too long
Change target surface
(e.g. white paper).
256
257
Received signal too high
Too much background light
Change target surface
(e.g. white paper).
Shadow target area.
258 Measurement outside of measuring range
Correct range.
260 Laser beam interrupted
Repeat measurement.
Care
• Clean the device with a damp, soft cloth.
• Never immerse the device in water.
• Never use aggressive cleaning agents or solvents.
Warranty
International Limited Warranty
The Leica DISTO™ comes with a two year warranty from Leica Geosystems AG. To receive an additional year warranty, the product must be registered on our website at http://myworld.leica-geosystems.com within eight weeks of the purchase date.
If the product is not registered, our two year warranty applies.
More detailed information about the International Limited Warranty can be found on the internet at: www.leica-geosystems.com/internationalwarranty.
Safety Instructions EN
The person responsible for the instrument must ensure that all users understand these directions and adhere to them.
Areas of responsibility
Responsibilities of the manufacturer of the original equipment:
Leica Geosystems AG
Heinrich-Wild-Strasse
CH-9435 Heerbrugg
Internet: www.disto.com
The company above is responsible for supplying the product, including the User
Manual in a completely safe condition.
The company above is not responsible for third party accessories.
Responsibilities of the person in charge of the instrument:
• To understand the safety instructions on the product and the instructions in the
User Manual.
• To be familiar with local safety regulations relating to accident prevention.
• Always prevent access to the product by unauthorised personnel.
Leica DISTO TM D510 792312c
27
Safety Instructions
Permitted use
• Measuring distances
• Tilt measurement
• Data transfer with Bluetooth
®
Prohibited use
• Using the product without instruction
• Using outside the stated limits
• Deactivation of safety systems and removal of explanatory and hazard labels
• Opening of the equipment by using tools
(screwdrivers, etc.)
• Carrying out modification or conversion of the product
• Use of accessories from other manufacturers without express approval
• Deliberate dazzling of third parties; also in the dark
• Inadequate safeguards at the surveying site
(e.g. when measuring on roads, construction sites, etc.)
• Deliberate or irresponsible behaviour on scaffolding, when using ladders, when measuring near machines which are running or near parts of machines or installations which are unprotected
• Aiming directly in the sun
Hazards in use
WARNING
Watch out for erroneous measurements if the instrument is defective or if it has been dropped or has been misused or modified.
Carry out periodic test measurements.
Particularly after the instrument has been subject to abnormal use, and before, during and after important measurements.
CAUTION
Never attempt to repair the product yourself. In case of damage, contact a local dealer.
WARNING
Changes or modifications not expressly approved could void the user’s authority to operate the equipment.
Limits of use
i
Refer to section "Technical data".
The device is designed for use in areas permanently habitable by humans. Do not use the product in explosion hazardous areas or in aggressive environments.
EN
Disposal
CAUTION
Flat batteries must not be disposed of with household waste. Care for the environment and take them to the collection points provided in accordance with national or local regulations.
The product must not be disposed with household waste.
Dispose of the product appropriately in accordance with the national regulations in force in your country.
Adhere to the national and country specific regulations.
Product specific treatment and waste management can be downloaded from our homepage.
Leica DISTO TM D510 792312c
28
Safety Instructions
Electromagnetic Compatibility
(EMC)
WARNING
The device conforms to the most stringent requirements of the relevant standards and regulations.
Yet, the possibility of causing interference in other devices cannot be totally excluded.
Use of the product with Bluetooth
®
WARNING
Electromagnetic radiation can cause disturbances in other equipment, in installations
(e.g. medical ones such as pacemakers or hearing aids) and in aircraft. It can also affect humans and animals.
Precautions:
Athough this product conforms to the most stringent standards and regulations, the possibility of harm to people and animals cannot totally excluded.
• Do not use the product near petrol stations, chemical plants, in areas with a potentially explosive atmosphere and where blasting takes place.
• Do not use the product near medical equipment.
• Do not use the product in airplanes.
• Do not use the product near your body for extended periods.
EN
Laser classification
The device produces visible laser beams, which are emitted from the instrument:
It is a Class 2 laser product in accordance with:
• IEC60825-1 : 2014 „Radiation safety of laser products“
Laser Class 2 products:
Do not stare into the laser beam or direct it towards other people unnecessarily. Eye protection is normally afforded by aversion responses including the blink reflex.
WARNING
Looking directly into the beam with optical aids (e.g. binoculars, telescopes) can be hazardous.
CAUTION
Looking into the laser beam may be hazardous to the eyes.
Description
Wavelength
Value
620 - 690 nm
Maximum radiant output power for classification < 1mW
Pulse repetition frequency 320 MHz
Pulse duration
Beam divergence
> 400 ps
0.16 x 0.6 mrad
Labelling
Subject to change (drawings, descriptions and technical data) without prior notice.
Leica DISTO TM D510 792312c
29
Leica Geosystems AG
CH-9435 Heerbrugg
(Switzerland) www.disto.com
Leica Geosystems AG, Heerbrugg, Switzerland has been certified as being equipped with a quality system which meets the International Standards of
Quality Management and Quality Systems (ISO standard 9001) and Environmental Management Systems (ISO standard 14001).
Total Quality Management - Our commitment to total customer satisfaction.
Ask your local Leica Geosystems agent for more information about our TQM program.
Copyright Leica Geosystems AG, Heerbrugg,
Switzerland 2017
Original text (792312c EN)
Pat. No.: WO 9427164, WO 9818019, WO 0244754, WO 0216964,
US 5949531, EP 1195617, US 7030969, US 8279421 B2,
Patents pending
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Instrument Set-up
- 3 Introduction
- 3 Overview
- 4 Basic measuring screen
- 4 Selection screen
- 5 Pointfinder (Viewscreen)
- 5 Insert batteries
- 6 Operations
- 6 Switching ON/OFF
- 6 Clear
- 6 Message Codes
- 6 Multifunctional endpiece
- 6 Permament / Minimum-Maximum measuring
- 7 Add / Subtract
- 7 Pointfinder (Viewscreen)
- 8 Settings
- 8 Overview
- 8 Tilt units
- 9 Distance units
- 9 Beep ON/OFF
- 9 Digital level ON/OFF
- 10 De-/Activate keylock
- 10 Switch on with keylock
- 10 De-/Activate Bluetooth® Smart
- 11 Calibration of tilt sensor (Tilt Calibration)
- 12 Personalized favorites
- 12 Illumination
- 13 Offset
- 13 Reset
- 14 Functions
- 14 Overview
- 14 Timer
- 14 Calculator
- 15 Adjusting measuring reference/tripod
- 16 Memory
- 16 Measuring single distance
- 16 Smart Horizontal Mode
- 17 Inclination tracking
- 17 Area
- 18 Volume
- 19 Triangular area
- 19 Long range mode
- 20 Height-profile measurement
- 21 Sloped objects
- 22 Height tracking
- 23 Trapezium
- 24 Stake out
- 25 Pythagoras (2-point)
- 26 Pythagoras (3-point)
- 27 Technical Data
- 28 Message Codes
- 28 Care
- 28 Warranty
- 28 Safety Instructions
- 28 Areas of responsibility
- 29 Permitted use
- 29 Prohibited use
- 29 Hazards in use
- 29 Limits of use
- 29 Disposal
- 30 Electromagnetic Compatibility (EMC)
- 30 Use of the product with Bluetooth®
- 30 Laser classification
- 30 Labelling