Altronix R615DC1016CB Installation manual


Add to my manuals
4 Pages

advertisement

Altronix R615DC1016CB Installation manual | Manualzz

Rack Mount Series

CCTV Power Supplies

Installation Guide

Models Include:

• R615DC1016

- 6-15VDC @ 10A.

- Sixteen (16) Fuse Protected Outputs.

• R615DC1016CB

- 6-15VDC @ 10A.

- Sixteen (16) PTC Protected Outputs.

Rev. 110909

Overview:

Altronix R615DC1016 Series Rack Mount CCTV Power Supplies provide 6-15VDC distributed via sixteen (16) fuse or

PTC protected outputs for powering CCTV cameras, heaters, and other video accessories.

Sixteen (16) Output Rack Mount Configuration Reference Chart:

Altronix

Model Number

R615DC1016

R615DC1016CB

Total

Output

Current

10A

Output

Voltage

6-15VDC

Number of

Outputs

16

PTC Protected

Outputs

(auto-resettable)

-----

P

Fuse

Protected

Outputs

P

-----

Output

Current

(max per output)

3.5A

2.5A

115VAC

50/60Hz

Input

Current

1.9A

Input:

• 115VAC, 50/60Hz, 1.9A.

Output:

• Sixteen (16) fuse or PTC protected outputs.

• 6-15VDC @ 10A total output current.

(0.625A per device, 3.5A max.)

• Outputs are rated @ 3.5A (fused) or 2.5A (PTC).

• Filtered and electronically regulated outputs.

• Short circuit and thermal overload protection.

Electrical:

• System AC input VA requirement: 218.5VA.

Specifications:

Features:

• Sixteen (16) power LEDs.

• Illuminated master power disconnect circuit breaker

with manual reset.

• 3-wire grounded line cord.

• Removable terminal blocks with locking screw flange.

• Spare fuses provided.

Rack Dimensions (H x W x D approximate):

• 2U rack mount chassis for use in standard EIA 19” rack.

3.26” x 19.125” x 8.5” (83mm x 486mm x 216mm).

Installation Instructions:

1. Unit is factory set at 12VDC. To adjust the output voltage remove the bottom cover to access trimpot on the power supply board (Fig. 1b, pg. 3).

2. Mount unit in the desired rack location (Space unit at least 3” from any video monitors).

3. Set power switch on the back of the unit to the OFF position (Fig. 1e, pg. 3).

4. Plug power cord into a grounded 115VAC, 50/60 Hz receptacle (Fig. 1d, pg. 3).

5. Set power switch to the ON (RESET) position and measure output voltage before connecting devices

(Fig. 1e, pg. 3). This helps avoiding potential damage.

6. Set power switch on the back of the unit to the OFF position (Fig. 1e, pg. 3).

7. Connect devices to the removable terminal blocks marked [1P & 1N through 16P & 16N] (Fig. 1c, pg. 3).

When wiring is completed on terminal blocks, they can be locked down by tightening screw flanges.

All terminals with common suffix (P) “1P, 2P...” are the same polarity (positive).

All terminals with common suffix (N) “1N, 2N...” are the same polarity (negative).

8. Upon completion of the wiring set power switch on the back of the unit to the ON (RESET) position (Fig. 1e, pg. 3).

9. Green power LEDs on faceplate will illuminate when AC power is present. When an output is in a trouble condition

(blown fuse or tripped PTC), the corresponding LED will not be illuminated (Fig. 1, pg. 3).

a. Blown fuse (R615DC1016) - Set power switch on the back of the unit to the OFF position (Fig. 1e, pg. 3).

Remove front faceplate to access fuses. Replace with fuses rated @ 3.5A/250VA (Altronix model # Fuse1).

b. Tripped PTC (R615DC1016CB) - To reset PTC set power switch on back of unit to the OFF position.

After approximately 30 secs. set power switch to the ON (RESET) position (Fig. 1e, pg. 3).

10. Power switch with built-in circuit breaker:

OFF position - Switch not illuminated. Outputs not powered.

RESET (ON) position - Switch illuminated. Outputs powered.

Circuit breaker tripped - Switch not illuminated. Power LEDs on faceplate are not illuminated. Outputs not powered.

To reset circuit breaker set power switch to the ON (RESET) position (Fig. 1e, pg. 3).

WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture. This installation should be made by qualified service personnel and should conform to the National Electrical

Code and all local codes.

- 2 - R615DC1016 Series

Fig. 1

Used on PTC

Models

Power

LED's

Power

LED's

Power

LED's

Power

LED's

PTC1

+ AC -+ DC --

Power Supply

Board

ALTRONIX CORP.

BKLYN, NY 11220

MADE IN U.S.A.

Trimpot

ALTRONIX CORP.

BROOKLYN, NY 11220

MADE IN USA

XFMR

Fig. 1a

(Green Wire

Earth GND)

XFMR

Trimpot

Fig. 1b

Removable Terminal

Block

Fig. 1c

Strain Relief

Line Cord

Fig. 1d

Power Switch

Fig. 1e

The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may be of sufficient magnitude to constitute an electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION: To reduce the risk of electric shock do not open enclosure. There are no user serviceable parts inside. Refer servicing to qualified service personnel.

R615DC1016 Series - 3 -

3.26"

83mm

Rack Mechanical Drawing and Dimensions (H x W x D approximate):

3.26” x 19.125” x 8.5” (83mm x 486mm x 216mm)

View from back

BACK

17.625"

447.7mm

8.5"

216mm

BOTTOM

0.75"

19.05mm

Altronix is not responsible for any typographical errors.

View from front

FACEPLATE

19.125"

486mm

E12Q MEMBER

R615DC1016 Series

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Key Features

  • 16 PTC protected outputs
  • 6-15VDC @ 10A total output current
  • Short circuit and thermal overload protection
  • Illuminated master power disconnect circuit breaker with manual reset
  • Removable terminal blocks with locking screw flange

Related manuals

Frequently Answers and Questions

How many outputs does the power supply have?
16
What is the total output current of the power supply?
10A
What type of protection does the power supply have?
Short circuit and thermal overload protection
Does the power supply have a master power disconnect circuit breaker?
Yes, with manual reset
Are the terminal blocks removable?
Yes, with locking screw flange
Download PDF

advertisement