HP rp5800 Base Model Retail System Installation Guide
Add to my manuals
2 Pages
HP rp5800 Retail System is a versatile and powerful device designed to enhance your retail operations. It features 12-volt Powered USB expansion cards that can be installed in the PCI Express x1 or x16 slots, allowing you to connect various peripherals such as barcode scanners, receipt printers, and external storage drives. With its dual 12-volt USB connectors, you can easily power and utilize multiple devices simultaneously, streamlining your workflow and increasing efficiency.
advertisement
▼
Scroll to page 2
12V Powered USB Card Installation Guide HP rp5800 Retail System © Copyright 2011 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice.The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Printed in Installing the Card 1. Turn off power to the system and disconnect the power cord from the power outlet. 2. Slide the access panel handle toward the rear of the computer 1 then lift the access panel up and off the computer 2. 3. Release the half-height slot cover retention latch by lifting the green tab on the latch and rotating the latch to the open position. 5. Hold the card just above the PCI Express expansion socket on the system board then align the bracket on the card with the open slot on the rear of the chassis 1. Press the card straight down into the expansion socket on the system board 2. 6. Before installing the Powered USB card be sure to power off the rp5800 and disconnect the power cord from the power outlet. 4. If you are installing two cards, connect the single end of each cable to the rear of the cards 1. Connect the green connectors on the other end of the cables to the green 12-volt USB connectors on the system board that are coupled together 2. Connect the black connectors to the two black 12-volt USB connectors on the system board 3. 8. Rotate the slot cover retention latch back in place to secure the expansion card. 9. Slide the lip on the front end of the access panel under the lip on the front of the chassis 1 then press the back end of the access panel onto the unit so that it locks into place 2. NOTE: You can install the Powered USB expansion card in the PCI Express x1 slot or the PCI Express x16 slot, or both. Two 12-volt Powered USB expansion cards are supported. First Edition: May 2011 Before You Begin 7. The cable included with the card has a single connector on one end and dual connectors on the other end. Connect the single end of the cable to the rear of the card 1. Connect the green connector on the other end of the cable to the green 12-volt USB connector on the system board 2. The cable will plug on one side of the green connector only. Connect the black connector to one of the two black 12-volt USB connectors on the system board 3. Remove the appropriate expansion slot cover on the back of the chassis. Pull the slot cover straight up then away from the inside of the chassis. WARNING! To avoid the risk of serious injury, ensure that the power cord is unplugged from the electrical outlet at the wall before installing the card. Failure to do so may expose you to the risk of electric shock. CAUTION: To avoid the risk of damage to the system, ensure that the power cord is unplugged from the electrical outlet at the wall before installing the card. NOTE: You can install the Powered USB expansion card in the PCI Express x1 slot or the PCI Express x16 slot, or both. Two 12-volt Powered USB expansion cards are supported. NOTE: The system board connectors allow you to install two 12volt Powered USB expansion cards. The green connectors on the system board are coupled together as one connector. The black connectors on the system board are separate connectors. 10. Reconnect the power cord and any external devices, then turn on the computer. Federal Communications Commission Notice European Union Regulatory Notice Localized Versions of this Document This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Products bearing the CE marking comply with the following EU Directives: Localized versions of this document are available at http://www.hp.com for the following languages: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio or television technician for help. • Low Voltage Directive 2006/95/EC • Brazilian Portuguese • EMC Directive 2004/108/EC • Dutch • Ecodesign Directive 2009/125/EC, where applicable • English CE compliance of this product is valid if powered with the correct CEmarked AC adapter provided by HP. • French • German Compliance with these directives implies conformity to applicable harmonized European standards (European Norms) that are listed in the EU Declaration of Conformity issued by HP for this product or product family and available (in English only) either within the product documentation or at the following web site: www.hp.eu/certificates (type the product number in the search field). • Bahasa Indonesian • Italian • Japanese • Korean The compliance is indicated by one of the following conformity markings placed on the product: • Simplified Chinese • Spanish • Traditional Chinese • Thai For non-telecommunications products and for EU harmonized telecommunications products, such as Bluetooth® within power class below 10mW. For EU non-harmonized telecommunications products (If applicable, a 4-digit notified body number is inserted between CE and !). Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the user's authority to operate the equipment. Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and Regulations. Declaration of Conformity for Products Marked with the FCC Logo (United States Only) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. For questions regarding the product, contact: Hewlett Packard Company P. O. Box 692000, Mail Stop 530113 Houston, Texas 77269-2000 Or, call 1-800-HP-INVENT (1-800 474-6836) Please refer to the regulatory label provided on the product. The point of contact for regulatory matters is Hewlett-Packard GmbH, Dept./MS: HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, GERMANY. German Ergonomics Notice HP products which bear the “GS” approval mark, when forming part of a system comprising HP brand computers, keyboards and monitors that bear the “GS” approval mark, meet the applicable ergonomic requirements. The installation guides included with the products provide configuration information. Japanese Notice For questions regarding this FCC declaration, contact: Hewlett Packard Company P. O. Box 692000, Mail Stop 510101 Houston, Texas 77269-2000 Or, call (281) 514-3333 To identify this product, refer to the Part, Series, or Model number found on the product. Korean Notice Canadian Notice This Class B digital apparatus complies with Canadian ICES-003. Avis Canadien Cet appareil numérique de la classe B est conforme à la norme NMB003 du Canada. Online Technical Support For the online access to technical support information, self-solve tools, online assistance, community forums or IT experts, broad multivendor knowledge base, monitoring and diagnostic tools, go to http://www.hp.com/support.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project